XL 575 PR-2590/PR-2590M

Transcription

1 XL 575 PR-2590/PR-2590M This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. LT.

2 INEX SFE USGE OF THE PROJETOR 3 INSTLLING THE PROJETOR 4 FITTING THE LMP 4 POWER SUPPLY MINS 5 ONTROL ONNETIONS 5 MX TERMINTOR 6 SETUP OPTIONS-PROJETOR ONFIGURTION 6 TO SET THE MX STRT RESS 6 OPERTION MENU 7 ERROR MESSGES 10 REPLING GOOS 10 MX PROTOOL 11 LE INITION 16 MINTENNE 16 LURITION 16 KEEPING THE PROJETOR LEN 16 TROULESHOOTING 17 TEHNIL T 18 ELETRIL IGRM 21 OMPONENT ORER OES 23 Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence arising from them. Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the unit. ny damage caused by improper use will not be assumed by the manufacturer and / or dealer. ESSORIES These items are packed together with the projector: Name Quantity Unit Remark G clamps 2 Pcs XLR cable 1 Pc 3-pin plug Safety cord 2 Pcs Spare gobos 4 Pcs This manual 1 Pc Ω clamps 2 Pcs Options 2/2

3 SFE USGE OF THE PROJETOR When unpacking and before disposing of the carton check there is no transportation damage before using the projector. Should there be any damage caused by transportation, consult your dealer and do not use the apparatus. The projector is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture, excessive heat, humidity and dust. o not allow contact with water or any other liquids. The projector is not designed or intended to be mounted directly on to inflammable surfaces. The projector is only intended for installation, operation and maintenance by qualified personnel. The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent wall surfaces. e sure that no ventilation slots are blocked. o not project the beam onto inflammable surfaces, minimum distance is 5m. 5m void direct exposure to the light from the lamp. The light is harmful to the eye. o not attempt to dismantle and/or modify the projector in any way. Electrical connection must only be carried out by qualified personnel. efore installation, ensure that the voltage and frequency of power supply match the power requirements of the projector. It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards. o not connect this device to any other types of dimmer apparatus. Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord. Keep the lamp clean. o not touch the lamp glass with bare hand. The projector should always be installed with a secondary safety fixing. safety cord is supplied for this; it should be attached as shown in installing the projector section. The lamp used in this projector is a discharge lamp. fter switching off don t attempt to restart the projector until lamp has cooled, this will require approx 15 minutes. Switching the lamp on and off at short intervals will reduce the life of both the lamp and the projector. ut occasional breaks will prolong the life of the lamp and projector. Never run the projector without a lamp. There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the covers removed. lways disconnect from the mains, when the device is not in use or before cleaning it or before attempting any maintenance work! If you have any questions, don t hesitate to consult your dealer or manufacturer. 3/3

4 INSTLL THE PROJETOR SFETY OR (2PS) WRNING To pass 2 SFETY ORS through the TRUSS for safety! LMPS (2PS) HNLES (2PS) TRUSS 339 Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WRNING on the underside of the base as shown above) To pass 2 SFETY ORS through the TRUSS for safety! lways ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. lways ensure that the structure that you are going to mount the projector is secure and is strong enough to support a weight of XL 575. WRNING: 1. Unlock the PN and TILT before the 1 st application of projector for safety. 2. The projector MUST be lifted or carried by the HNLES instead of clamps. 3. For safety the safety cord should afford 10 times of the unit s weight. 106 FITTING THE LMP LMP REFLETER NUT Lock the yoke before fitting/replacing the lamp. Loosen 4 screws and open the back covers, you can see the structure as shown in the figure above. Loosen 2 nuts at the both ends of lamp and take out the worn-out lamp. Suggest to free one end after another. Fit new lamp and fasten 2 screws at the both ends of lamp. Note: don t touch the bulb of the new lamp with bare hand so as not to influence the beam output; the PST (pumping stem tip off) on the bulb facing the rear cover with fans perpendicularly and being not in the beam s way is a must and aids cooling. lose the rear cover and fasten 4 screws. NOTE: The convex of the nuts should face to the side when fitting the lamp. WRNING: The MSI series are high-pressure lamps with external igniters ( ). are should always be taken when handling these lamps. lways read the manufacturers "Instructions for use" enclosed with the lamp. 4/4

5 POWER SUPPLY-MINS onnect the power cord as follows: L (live) =brown E (earth) =yellow/green N (neutral) =blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector. It is recommended that each projector be supplied separately so that they may be individually switched on and off. IMPORTNT It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards. ONTROL ONNETION onnection between controller and projector and between one projector and another must be made with a 2 core-screened cable, with each core having at least a 0.5mm diameter. onnection to and from the projector is via cannon 3 pin (which are included with the projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above. Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of the plug is not connected in any way. The XL 575 accepts digital control signals in protocol MX512 (1990). onnect the controller s output to the first fixture s input, and connect the first fixture s output to the second fixture s input and connect the rest fixtures in the same way. Eventually connect the last fixture s output to a MX terminator as shown in the figure below. No.1 No.2 No. n MX IN MX OUT MX IN MX OUT MX IN MX OUT MX IN ONTROLLER TERMINTER 5/5

6 MX TERMINTOR In the ontroller mode, at the last fixture in the chain, the MX output has to be connected with a MX terminator. This prevents electrical noise from disturbing and corrupting the MX control signals. The MX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is then plugged into the output socket on the last projector in the chain. The connections are illustrated below MX TERMINTOR ONNETION onnect a 120 (OHM) resistor across pins 2 and 3 in an XLR plug and insert into the MX out socket on the last unit in the chain. PIN 2 PIN 3 SETUP OPTIONS-PROJETOR ONFIGURTION OER UTTON UP Projector configuration can be set conveniently via pressbutton switch and L display. Turn the projector on and the L display will show MX address you set and save last time and it can be reset and saved again as you please. Launch the projector. Press button ENTER more than 5 seconds to unlock panel. Press button UP or OWN if you want to browse through the various Setup Options. There are 8 option codes from MX ddress to Lamp Manual ontrol, and each code has a specific function. If you turn the coder knob clockwise, the function like as button UP. On the contrary, the function like as button OWN. Press button ENTER to save your settings or enter the next menu. There is same function if you push the coder knob. Press button UP or OWN to shift. Press button FUN, it will return to the upper menu one by one. If you stay for minutes defaulted will show display status automatically. UP TO SET THE MX STRT RESS Each XL 575 must be given a MX start address so that the correct projector responds to the correct control signals. This MX start address is the channel number from which the projector starts to listen to the digital control information being sent out from the controller. The XL 575 has 3 MX modes. There are stand mode, extended mode and short mode. For example stand mode has 19 channels, so set the No. 1 projector s address 001, No. 2 projector s address 020, No. 3 projector s address 039, No. 4 projector s address 058, and so on. Launch the projector. Press button ENTER or coder knob more than 5 seconds to unlock panel. Press button FUN to display MX address; Press button UP and OWN, you can set the address; Press button ENTER to confirm; In the same time. The GREEN LE will flash one time. It means the setting has been enabled. Press button FUN, it will return to the upper menu one by one. 6/6

7 OPERTION MENU 1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL XL SERIES XL 575 MX ddress Reset onfig Settings Option Settings MX ddress=001 MX ddress Reset re You Sure? MX Mode Lamp ontrol Fixture type (WRNING Never change the fixture type or the system will be damaged!) olour Positions F-Gobo Positions Pan MX Invert MX Mode Standard 16 MX Mode Extended 16 MX Mode Short 8 Lamp ontrol y ontrol hannel Lamp ontrol y Power On Lamp ontrol y MX Present Fixture type= XL 1200 Fixture type= XL 700 Fixture type= XL 575 Fixture type= XL 1200 FS Fixture type= XL 1200 Wash Fixture type= XL 700 Wash olour Positions STEPPE olour Positions LINER F-Gobo Positions STEPPE F-Gobo Positions LINER Pan MX Invert OFF Pan MX Invert ON 7/7

8 isplay Options Tilt MX Invert Pan Tilt Swap immer Invert Iris Invert Zoom Invert efaults isplay Mode isplay imming Tilt MX Invert OFF Tilt MX Invert ON Pan Tilt Swap OFF Pan Tilt Swap ON immer Invert OFF immer Invert ON Iris Invert OFF Iris Invert ON Zoom Invert OFF Zoom Invert ON efaults OFF efaults Restore efaults isplay On lways isplay Off fter elay isp im Level Min isp im Level 1 isp im Level 2 isp im Level 3 isp im Level 4 isp im Level 5 isp im Level 6 isp im Level 7 isp im Level 8 8/8

9 Information Test Modes Lamp Manual ontrol isplay ontrast isplay Language Lamp Hours Total Hours Temperature Software Version Factory Setup Self Test Lamp Status Turn Lamp On Turn Lamp Off isp im Level 9 isp im Level Full isplay ontrast XXX(1~36, efault is 16) Language = English Language = hinese Lamp Hours = XX Total Hours = XX isplay oard river oard 1 river oard 2 Pan and Tilt isplay oard river oard 1 river oard 2 Pan and Tilt Power oard Factory Setup OFF Factory Setup ON Self Test OFF self test ON Status = XXX ontrol = X Reset Lamp Hours re You Sure? isplay oard = XX river oard 1 = XX river oard 2 = XX Pan and Tilt = XX isplay oard = X.X.X river oard 1 = X.X.X river oard 2 = X.X.X Pan and Tilt = X.X.X Power oard = X.X.X 9/9

10 ERROR MESSGES In the course of launch, XL 575 examines automatically whether there are errors and if there are, it will display information as follows: isplay Sensor Err S1-M1 Sensor Err S1-M2 Sensor Err S1-M3 Sensor Err S1-M4 Sensor Err S2-M1 Sensor Err S2-M2 Sensor Err S2-M3 Sensor Err S2-M5 Sensor Err S2-M6 Message olour wheel 1 (1# drive board motor 1) error Prism (1# drive board motor 2) error Prism rotation (1# drive board motor 3) error olour wheel 2 (1# drive board motor 4) error Rotating Gobo wheel 1 (2# drive board motor 1) error Gobo rotation 1 (2# drive board motor 2) error Fixed Gobo wheel (2# drive board motor 3) error Focus (2# drive board motor 5) error Zoom (2# drive board motor 6) error REPLING GOOS FIXE GOO WHEEL PRISM/FROST ROTTING GOO WHEEL 1 OLOUR WHEEL 1 OLOUR WHEEL 2 isconnect the fixture from power. Lock Tilt. arefully lift off the cover by undoing the 6 screws. For gobos replacement on the fixed gobo: Remove the gobo and insert the new one into the position by hands. For gobos replacement on the rotating gobo wheel: Remove the gobo holder with gobo from gobo wheel by hands. Pull out the spring and drop the old gobo out of the holder. Insert the new gobo into the holder, and then insert the spring with the narrow end against the gobo. Push the end of the spring in under lip of the holder. Pick the spring clip up and put the gobo holder back into the position, if necessary, a small screwdriver will be helped. Note: If the gobo is a glass one, it should be touched with glabrous, clean and soft tissue or cloth matted between hand and glass instead of with bare hand. lose the rear cover and fasten 6 screws. 10/10

11 MX PROTOOL Short mode Standard mode Extended mode Strobe immer FUNTION MX ESRIPTION lack Open Strobe speed from slow to fast Open lack imming from dark to light (0-100%) 3 immer Fine immer in 16 it precision olour Wheel White (Note: stop in MX value 5,6 or 7 for 5s to activate the reset function) White/colour 1 11/ olour olour 1/colour olour olour 2/colour olour olour 3/colour olour olour 4/colour olour olour 5/colour olour olour 6/colour white Rainbow rotation speed 1 (slowest) Rainbow rotation speed Rainbow rotation speed Rainbow rotation speed Rainbow rotation speed Rainbow rotation speed Rainbow rotation speed Rainbow rotation speed Rainbow rotation speed Rainbow rotation speed Stop in current position Rainbow reverse rotation speed 1(slowest) Rainbow reverse rotation speed Rainbow reverse rotation speed Rainbow reverse rotation speed Rainbow reverse rotation speed 5

12 4 4 5 olour Wheel Rainbow reverse rotation speed Rainbow reverse rotation speed Rainbow reverse rotation speed Rainbow reverse rotation speed Rainbow reverse rotation speed White White/colour olour olour 1/colour olour olour 2/colour olour olour 3/colour olour olour 4/colour olour olour 5/colour olour olour 6/colour white Rainbow rotation speed 1 (slowest) Rainbow rotation speed Rainbow rotation speed Rainbow rotation speed Rainbow rotation speed Rainbow rotation speed Rainbow rotation speed Rainbow rotation speed Rainbow rotation speed Rainbow rotation speed Stop in current position Rainbow reverse rotation speed 1(slowest) Rainbow reverse rotation speed Rainbow reverse rotation speed Rainbow reverse rotation speed Rainbow reverse rotation speed Rainbow reverse rotation speed Rainbow reverse rotation speed Rainbow reverse rotation speed Rainbow reverse rotation speed Rainbow reverse rotation speed Iris from large to small (0-100%) Iris Macro Minimal 7 Iris Fine Iris n 16 it precision 12/12

13 6 6 8 Fixed Gobo Wheel Rotating Gobo Wheel lear Gobo Gobo Gobo Gobo Gobo Gobo Gobo Reverse rotation speed 1 (slowest) Reverse rotation speed Reverse rotation speed Reverse rotation speed Reverse rotation speed Reverse rotation speed Reverse rotation speed 7(fastest) Rotation speed 1 (slowest) Rotation speed Rotation speed Rotation speed Rotation speed Rotation speed Rotation speed 7(fastest) Gobo 1 shake 1(slowest) Gobo 1 shake Gobo 1 shake Gobo 1 shake 4 fastest Gobo 2 shake 1(slowest) Gobo 2 shake Gobo 2 shake Gobo 2 shake 4 fastest Gobo 3 shake 1(slowest) Gobo 3 shake Gobo 3 shake Gobo 3 shake 4 fastest Gobo 4 shake 1(slowest) Gobo 4 shake Gobo 4 shake Gobo 4 shake 4 fastest Gobo 5 shake 1(slowest) Gobo 5 shake Gobo 5 shake Gobo 5 shake 4 fastest Gobo 6 shake 1(slowest) Gobo 6 shake Gobo 6 shake Gobo 6 shake 4 fastest Gobo 7 shake 1(slowest) Gobo 7 shake Gobo 7 shake Gobo 7 shake 4 fastest white Gobo Gobo Gobo Gobo Gobo Rotation speed 1 (slowest) Rotation speed Rotation speed Rotation speed 4 (fastest) 13/13

14 Gobo rotation 9 11 Gobo rotation Fine Prism / Frost Prism rotation Reverse rotation speed 1 (slowest) Reverse rotation speed Reverse rotation speed Reverse rotation speed 4(fastest) Gobo 1 shake slow Gobo 1 shake fast Gobo 2 shake slow Gobo 2 shake fast Gobo 3 shake slow Gobo 3 shake fast Gobo 4 shake slow Gobo 4 shake fast Gobo 5 shake slow Gobo 5 shake fast ~540 index Rotation speed 1 (slowest) Rotation speed Rotation speed Rotation speed Rotation speed Rotation speed Rotation speed Rotation speed 8 (fastest) Stop rotating Reverse rotation speed 1 (slowest) Reverse rotation speed Reverse rotation speed Reverse rotation speed Reverse rotation speed Reverse rotation speed Reverse rotation speed Reverse rotation speed 8 (fastest) Gobo rotation in 16 it precision lear TO Frost Prism Prism Prism index 0~ Reverse rotation speed 1 (slowest) Reverse rotation speed Reverse rotation speed Reverse rotation speed Reverse rotation speed Reverse rotation speed Reverse rotation speed Reverse rotation speed 8 (fastest) Stop in current position Rotation speed 1 (slowest) Rotation speed Rotation speed Rotation speed Rotation speed Rotation speed Rotation speed Rotation speed 8 (fastest) Wheel full into beam gradually Stop in current position Reverse rotation speed from slow to fast 14/14

15 Focus Linearly focusing 15 Focus Fine Focus in 16 precision Zoom From large to small 17 Zoom Fine Zoom in 16 precision Pan Pan rotation Pan Fine Pan rotation in 16 precision Tilt Tilt rotation Tilt Fine Tilt rotation in 16 precision Pan & Tilt speed ontrol Pan&Tilt speed from fast to slow Reserved Reset Reserved Lamp off ( stop in MX value for 10 s) Reserved Lamp power reduced to 50% Reserved Lamp on (See remark below) Remark: If you intend to turn on/off the lamp via the last channel of the controller, don t attempt to push the channel to value immediately after turning it off, or push the slide bar to value to wait it cooling. Under these 2 circumstances, the lamp can not be turned on. The right operation is: turn it off---cool down---push the slide bar to turn it on. 15/15

16 LE INITION On MX signal OK Green Off No MX signal Flash MX signal error Red On Running self test mode Yellow On Setting the panel lue On Power MINTENNE If the projector s lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in any way it must be replaced. If the light from the lamp appears dim this would normally indicate that it is reaching the end of its life and it should be changed at once, aged lamps run to the extremity of their life might explode. If the projector does not function, check the fuses on the power socket of the projector, they should only be replaced by fuses of the same specification. Should these be damaged call a qualified technician before replacement. The projector has thermal protection device that will switch off the projector in case of overheating, should either of these operate, check that the fans are not blocked, and if they are dirty clean them before switching on the projector again. heck that the fans are operational, if not call a qualified technician. ny maintenance work should only be carried out by qualified technicians. LURITION To ensure the continuous rotation of the rotating gobos and linear motion of the lens for focusing, it is recommended that the bearings for the rotating gobos and the 2 shafts for the focusing lens holder be lubricated periodically, preferably every two months. Use only high quality, high-temperature resistant grease instead of any type of oil. When lubricating the bearings, a syringe with a fine needle is the easiest way to introduce the grease to the bearings around each gobo. KEEPING THE PROJETOR LEN To ensure the reliability of the projector it should be kept clean. It is recommended that the fans should be cleaned every 15 days. The lens and dichroic colour filters should also be regularly cleaned to maintain an optimum light output. o NOT use any type of solvent on dichroic colour filters. leaning frequency depends on the environment in which the fixture operates: damp, smoke or particularly dirty surroundings can cause greater accumulation of dirt on the unit s optics. soft cloth and typical glass cleaning products should be used in cleaning. It is recommended to clean the external optics at least once every 20 days and clean the internal optics at least once every 30 / 60 days. o not use any organic solvent, e.g. alcohol, to clean the reflector mirror, dichroic colour filters or housing of the apparatus. 16/16

17 TROULESHOOTING PROLEM The projector doesn t switch on The lamp comes on but the projector doesn t respond to the controller TION heck the fuse on the power socket. Replace the lamp. Make sure that the projector is correctly configurated. Replace or repair the MX cable. The projector only functions intermittently Make sure the fan is working and not dirty. efective projection The project image appears to have a halo The beam appears dim heck the lenses are not broken. Remove dust or grease from the lenses. Make sure the lamp is installed correctly. arefully clean the optical group lenses and the projector components. heck the optics is clean. Replace with a new lamp of the specified type and rating. 17/17

18 TEHNIL T VOLTGES: Electronical ballast PR-2590 : 100V/120V/200V/220V/230V/240V 50/60Hz Magnetic ballast PR-2590M : 100V/120V/200V/220V/230V/240V 50/60Hz POWER ONSUMPTION: Electronical ballast PR-2590 : Magnetic ballast PR-2590M : 650W@220V 710W@220V LMP: PHILIPS MSI 575 HR olour Temperature 6000 K Socket SFc10-4 double ended Manufacturers Rated Lamp Life 750 Hours replacement Or OSRM HMI 575 W/GS olour Temperature 6000 K Socket SFc10-4 double ended Manufacturers Rated Lamp Life 1000 Hours replacement OLOURS: 2 wheel each with 6 dichroic colour filters plus white With variable speed bi-directional rainbow effect Step/linear colour changing is available OLOUR TEMPERTURE ORRETION: Linearly colour temperature correction GOOS: 1 Rotating gobo wheel: 5 interchangeable gobos+ white, glass or metal gobos can be fixed Indexable, bi-directionally rotatable at variable speeds 1 Fixed gobo wheel : 7 interchangeable gobos+ white bi-directional wheel scrolling at variable speeds Gobo diameter: Φ36.3mm Gobo image diameter: Φ31.5mm PRISM/ FROST: 1x linear lens, 1x3 facet prism, indexable, bi-directionally rotatable at variable speeds 1xfrost, 1xTO 18/18

19 FOUS: MX controlled focus IMMER: 0-100% linearly adjustable SHUTTER: ouble shutter blades, 0.3~12 F.P.S Macros HE MOVEMENT: Pan 450º, Tilt 270º with auto position correction EM NGLE: 12 34, linearly adjustable ONTROL: MX512, 3 pin interface 15 channels in short mode, 19 channels in stand mode, and 23 channels in extended mode. Self-test mode OTHER FUNTIONS: djustable Pan & Tilt speed Fixture and lamp usage time display L display with English and hinese language menu Energy saving function of the ballast uilt-in analyzer for easy fault finding, error messages uilt-in demo sequences Setup options by chargeable battery inside without power connection. Input signal isolating protection Network interface (Reserved) HOUSING: omposite plastic, IP20 WEIGHT: Electronical ballast PR-2590 : Magnetic ballast PR-2590M : 29Kg 34Kg 19/19

20 SIZES: See at below LIGHT OUTPUT: 34 lux 12 lux m 8m 0m 8m 16m 20m 12m 4m 4m 12m 20m ISTNE (m) IMETER (m) IMETER (m) /20

21 Thermostat OX FN P FN HE FN 1 HE FN n N ap-1 ap-2 FN1 FULL FN2 FULL FN3 3 / 4 FN4 HLF PITOR IGNITER LLST MX-SENS2 MX-SENS1 GN GN 12V + 230V N +12V G G +24V +24V FG ELETRONI TRNSFORMER 60Hz 50Hz LMP L INPUT N E SWITH Filter - L L GN FN-POWER -SELET GN FN-POWER HIGH allast N6 Thermostat H N P P H L FN & LIGHTING P V V Ph 60Hz 50Hz L LOW allast Ph GN FN-POWER MOTOR1 MOTOR2 MOTOR3 MOTOR4 MOTOR5 MOTOR6 SLVE #1 P MX-SENS2 MX-SENS1 V V GN GN V G S V G S V G S SENS5 SENS6 SENS3 SENS4 SENS1 SENS2 V G S V G S V G S HLL 1-3 HLL 1-1 HLL 1-4 HLL 1-2 MOTOR1 MOTOR2 MOTOR3 MOTOR4 MOTOR5 MOTOR6 MX-SENS2 MX-SENS1 V V GN GN SLVE #2 P V G S V G S V G S SENS5 SENS3 SENS1 SENS6 SENS4 SENS2 V G S V G S V G S HLL 2-5 HLL 2-3 HLL 2-6 HLL 2-1 HLL 2-2 PN ENOE MX-IN MX-OUT MX-IN MX-OUT MLE FEMLE MLE FEMLE T+ T- GN PN TILT TILT ENOE G S2 S1 V V + S1 S2 PN & TILT P G V S G G S V ELETRIL IGRM PR-2590M LE4 LE1 GN GN V V MX-SENS1 MX-SENS2 LE3 LE2 M1-1 OLOUR-1 M1-2 M1-3 PRISM PRISM ROTTING M1-4 OLOUR-2 M1-6 IMMER M2-1 ROTTING-GOO M2-2 GOO ROTTING M2-3 FIXE GOOS M2-4 IRIS L ISPLY FUNTION OWN UP ENTER + - attery J1 J2 PN TILT MX-SENS2 MX-SENS1 V V GN GN 6V GN M1-5 STROE M1-6 IMMER M1-5 STROE M2-5 FOUS M2-6 ZOOM M2-5 FOUS M2-6 ZOOM FUSE 21/21

22 + MOTOR1 MOTOR2 MOTOR3 MOTOR4 MOTOR5 MOTOR6 SLVE #1 P MX-SENS2 MX-SENS1 V V GN GN SENS5 SENS3 SENS1 SENS6 SENS4 SENS2 V G S V G S V G S MOTOR1 MOTOR2 MOTOR3 MOTOR4 MOTOR5 MOTOR6 SLVE #2 P MX-SENS2 MX-SENS1 V V GN GN SENS5 SENS3 SENS1 SENS6 SENS4 SENS2 V G S V G S V G S TILT ENOE PN & TILT P Title - - V G S V G S V G S HLL 1-3 HLL 1-1 HLL 1-4 HLL 1-2 V G S V G S V G S HLL 2-5 HLL 2-3 PN ENOE MX-IN MX-OUT MX-IN MX-OUT MLE FEMLE MLE FEMLE T+ T- GN PN TILT G S2 S1 V V G S V S1 S2 G S G V L INPUT N E Filter LE4 LE1 GN GN V V MX-SENS1 MX-SENS2 LE3 LE2 M1-1 M1-2 M1-3 M1-4 M1-5 M1-6 OLOUR-1 PRISM PRISM ROTTING OLOUR-2 STROE IMMER M2-1 M2-2 M2-3 M2-4 M2-5 M2-6 ROTTING-GOO GOO ROTTING FIXE GOOS IRIS FOUS ZOOM L ISPLY MX-SENS2 MX-SENS1 V V GN GN 6V GN FUNTION OWN UP ENTER + - attery HE FN J1 PN J2 TILT SWITH ELETRONI TRNSFORMER +12V G G +24V +24V FG HE FN OX FN GN FN-POWER GN FN-POWER STROE IMMER LMP IGNITOR GROUN ELETRONI LLST N TO IGNITOR Thermostat MX-SENS2 MX-SENS1 GN GN FN1 G G FULL FN & LIGHTING P 12V + - FN2 FULL FN3 3 / 4 FN4 HLF L ELETRIL IGRM PR-2590 M2-5 M2-6 FOUS ZOOM HLL 2-1 HLL 2-6 HLL 2-2 FUSE 22/22

23 OMPONENT ORER OES NME PRT NO. QUNTITY REMRK POWER SUPPLY V/12V THERMOSTT SWITH V PITOR**** µF/370V LLST**** W/ 95V 3.6 LLST W 90~264V IGNITOR**** ~1200W 6~8KV IGNITOR ~1200W LMP MSI 575W HR FUSE /250V 6.35*30 TILT RIVE ELT HT-750-3M PN RIVE ELT HT501-3M FN IN FRONT SIE K1208PTS1-6 12V/2.6W FN NER THE LMP V 0.38 FN IN SE**** V /1.9W FN IN K SIE V 0.3 FN NER THE YM KE1205PFV1 11MS PN MOTOR 1 23HS2039L 6.35* TILT MOTOR 1 23HS2039L 6.35*25 PRISM ROTTION MOTOR HY L 5*24 ROTTING GOO WHEEL MOTOR PRISM/FROST MOTOR 1 17H L 5*7 FOUS MOTOR ZOOM MOTOR 2 17HS *20 OLOUR WHEEL MOTOR1 1 OLOUR WHEEL MOTOR IMMER MOTOR 2 17H L 5*23 GOO ROTTION MOTOR 1 FIXE GOO WHEEL MOTOR HY *18 SHUTTER LE MOTOR HY L 5*15 IRIS MOTOR YG *24 PN/TILT RIVE P MOTOR RIVE P MOTOR RIVE P ISPLY P POWER P POWER P**** NOTE: **** Only apply to Magnetic ballast. 23/23

24 LT. 571 Yingbin Road, ashi, Panyu, Guangzhou , hina TEL: FX: /24 P/N: Last Revision: 13:10:2006