USB-IF Product Order Form Please use the following information to select the test hardware from the USB-IF estore. Low-speed Functional Compliance Test Device The LS Functional Compliance Test Device is used by high-speed hub vendors to validate transaction translators. Please use product code USBLSTD to order. Member Price: $90.00 Non-Member Price: $110.00 Full-speed Functional Compliance Test Device The FS Functional Compliance Test Device is used by high-speed hub vendors to validate transaction translators. Please use product code USBFSTD to order. Member Price: $250.00 Non-Member Price: $300.00 The USB 3.0 xhci-based Peripheral Development Kit (PDK) provides a host-side solution. It is intended to assist companies who are developing peripherals. This kit ships with a 1-meter SuperSpeed USB cable to be used in conjunction with the PDK. Please use product code USB3PDK_FL to order the Fresco Logic host-side solution. Member Price: $800.00 Non-Member Price: $1000.00 - NOT accepting new orders at this time Please use product code USB3PDK_REN to order the Renesas host-side solution. Member Price: $800.00 Non-Member Price: $1000.00 USB 3.0 Electrical Test Fixture Kit The USB 3.0 Electrical Test Fixture Kit provides a worst case, ISI hardware channel for PHY s. It is intended to assist companies in testing transmitter signal quality and receiver sensitivity for either hosts or peripherals. This kit ships with the necessary cables to be used in conjunction with the fixtures. Please use product code USB3ET to order. Member Price: $700.00 Non-Member Price: $950.00 USB 3.0 Cable Kit The USB 3.0 Cable Kit provides five (5) SuperSpeed USB (USB 3.0) cables: - Standard A to Standard B, 3 meter - Standard A to Micro B, 1 meter - Standard A to Standard B, 8 inch - Standard A to Standard B, 4 inch - Standard A to Micro B, 4 inch Please use product code USB3CABLES to order. Member Price: $150.00 Non-Member Price: $200.00 USB 2.0 Link Power Management (LPM) Peripheral Development Kit (PDK) - NOT accepting new orders at this time The USB 2.0 Link Power Management (LPM) Peripheral Development Kit (PDK) provides a host-side solution. It is intended to assist companies who are developing USB peripherals with the LPM feature Please use product code LPM_PDK to order. Member Price: $800.00 Non-Member Price: $1000.00 Page 1 of 6
USB 2.0 / 3.0 Drop-Droop Fixture The USB 2.0 / 3.0 Drop-Droop Fixture is intended to assist companies in testing voltage drop and droop levels for hosts or hubs. The cables required to be used in conjunction with the fixture are included. Please use product code USB2/3_DD to order. Member Price: $450.00 Non-Member Price: $500.00 Over Current Test Fixture The over-current test fixture can be used to test and trigger current fault protection on a USB port by creating an over-current condition. The fixture is capable of drawing a variable load from 300mA to 1.8A and also includes a safety shut down to prevent overheating. Please use product code USBOVER to order. Member Price: $350.00 Non-Member Price: $450.00 USB 2.0 Hi-Speed Signal Quality Test Fixture Set The USB 2.0 Hi-Speed Signal Quality Test Fixtures are used for testing signal quality of hi-speed hosts and peripherals. The fixtures eliminate the need for probes and require quality SMA cables for direct connection to the scope. The fixtures include USB cables but do not include SMA cables. Please use product code USB2SIGQUAL to order. Member Price: $650.00 Non-Member Price: $900.00 Page 2 of 6
Product Order Form Please PRINT and FAX the completed order form including payment information to the USB-IF at 503-644-6708. Or mail with payment to: USB Implementers Forum 3855 SW 153 rd Dr. Beaverton, Oregon 97003 Phone: 503-619-0426 The following table is for use by Members of the USB Implementers Forum only: Company Name: Vendor ID: (Decimal) Product Code: Description: Quantity: Members Unit Price: USBLSTD Low Speed Functional Compliance Test Device $90.00 USD USBFSTD Full Speed Functional Compliance Test Device $250.00 USD USB3PDK_FL (Fresco Logic host) $800.00 USD USB3PDK_REN (Renesas host) $800.00 USD USB3ET USB 3.0 Electrical Test Fixture Kit $700.00 USD USB3CABLES USB 3.0 Cable Kit $150.00 USD LPM_PDK USB 2.0 Link Power Management (LPM) Peripheral Development Kit (PDK) $800.00 USD USB2/3_DD USB 2.0 / 3.0 Drop-Droop Fixture $450.00 USD USBOVER Over Current Fixture $350.00 USD USB2SIGQUAL USB 2.0 Hi-Speed Signal Quality Test Fixture Set $650.00 USD Total Payment Due: Extended Price: Shipping and Handling Fees are included in the prices above. Duties, customs and other taxes are not included within the above prices. You should receive an invoice from the carrier and/or customs for any additional expense incurred. It is your responsibility, and not that of USB-IF, to pay these taxes. See next page for Non-Member pricing. Page 3 of 6
The following table is for use by Non-Members of the USB Implementers Forum: Company Name: Vendor ID: (Decimal) Product Code: Description: Quantity: Non-Members Unit Price: USBLSTD Low Speed Functional Compliance Test Device $110.00 USD USBFSTD Full Speed Functional Compliance Test Device $300.00 USD USB3PDK_FL (Fresco Logic host) $1,000.00 USD USB3PDK_REN (Renesas host) $1,000.00 USD USB3ET USB 3.0 Electrical Test Fixture Kit $950.00 USD USB3CABLES USB 3.0 Cable Kit $200.00 USD LPM_PDK USB 2.0 Link Power Management (LPM) Peripheral Development Kit (PDK) $1,000.00 USD USB2/3_DD USB 2.0 / 3.0 Drop-Droop Fixture $500.00 USD USBOVER Over Current Fixture $450.00 USD USB2SIGQUAL USB 2.0 Hi-Speed Signal Quality Test Fixture Set $900.00 USD Total Payment Due: Extended Price: Shipping and Handling Fees are included in the prices above. Duties, customs and other taxes are not included within the above prices. You should receive an invoice from the carrier and/or customs for any additional expense incurred. It is your responsibility, and not that of USB-IF, to pay these taxes. Page 4 of 6
Payment information: Please indicate the form of payment to be used. Orders will be processed upon receipt of properly completed order form and payment in full. Check enclosed in U.S. Funds drawn on U.S. bank, payable to: USB Implementers Forum Wire transfer (contact admin@usb.org to request bank details) Credit Card (complete the information below) Card Holder Information: Card Holder Name: Telephone: Email: Billing Address: Mail Stop: City: Zip / Postal Code: Credit Card Information: Fax: State/Province: Country: Card Type: (Please select one) VISA MASTERCARD AMERICAN EXPRESS Card Number: Expiration: CVV code: (for Visa & MasterCard: 3-digit code on back of card; for American Express: 4-digit code on front of card) Card Holder Name (As is appears on the card): I hereby authorize the USB Implementers Forum to charge the amount of $ to the credit card listed above for this purchase. Card Holder Signature: Date: Shipping Information: Orders must contain a complete shipping address and phone numbers for items to be fulfilled. No P.O. Boxes. Recipient's Contact Information: Ship Attention to: Company Name: Address: City: Zip / Postal Code: Email: Mail Stop: State/Province: Country: Telephone: ALL PRODUCTS AND DOCUMENTS OFFERED FOR SALE BY USB-IF ARE PROVIDED "AS IS" AND WITHOUT ANY WARRANTY OF ANY KIND, EXPRESS OF IMPLIED. WITHOUT LIMITATION, THERE IS NO WARRANTY OF NON- INFRINGEMENT, NO WARRANTY OF MERCHANTABILITY, AND NO WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ALL WARRANTIES ARE EXPRESSLY DISCLAIMED. USER ASSUMES THE FULL RISK OF USING SUCH PRODUCTS AND DOCUMENTS. IN NO EVENT SHALL USB-IF BE LIABLE FOR ANY ACTUAL, DIRECT, INDIRECT, PUNITIVE, OR CONSEQUENTIAL DAMAGES ARISING FROM SUCH USE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SALE OF PRODUCTS AND TESTING COMPONENTS THROUGH THIS ORDER FORM DOES NOT IMPLY SUCH PRODUCTS AND TESTING COMPONENTS ARE CERTIFIED AND/OR ENDORSED BY USB-IF. THESE PRODUCTS ARE FOR TESTING PURPOSES ONLY AND NOT FOR RESALE. Page 5 of 6
Purchasing/Return Policy If you wish to purchase products described on the usb.org web site, you will be asked to supply certain information, including but not limited to credit card or other payment information. You agree all information you provide to the USB-IF will be accurate, complete and current. You agree to pay all charges incurred by authorized users of your account and credit card or other payment mechanism at the prices in effect when such charges are incurred. You will also be responsible for paying any applicable taxes, and shipping and handling charges relating to your purchases. Non-Defective Products We will not accept returns on non-defective products. Defective Products Defective products may be returned for either exchange or repair (at the discretion of the USB-IF) within 30 days from the shipment date. No defective product will be accepted without a return authorization (RA) number. To request a RA number, please contact a USB-IF Customer Service Specialist; please see the contact information below. RA numbers are valid for ten business days after issue. Your RA number(s) must appear clearly on the shipping label of the return shipment. Affix a label to the box: PLEASE DO NOT MARK THE BOX ITSELF IN ANY WAY. If you have questions, please contact us at: USB Implementers Forum 3855 SW 153 rd Dr. Beaverton, OR 97003 Phone: 1-503-619-0426 Fax: 1-503-644-6708 Email: admin@usb.org Page 6 of 6