Electrotechnology Training Package UEE11 Refrigeration, Air Conditioning and Appliance Servicing Qualifications Skill Sets Competency Standard Units This national training package endorsed in December 11 and it contains qualifications from Certificate 1 to Advanced Diploma level and over 600 competency standard units. It replaced the majority of existing Refrigeration, Air Conditioning and Appliance Servicing Qualifications and Competency Standards Units to meet National Quality Council requirements for flexibility and sustainable work practices. The full training package is available on the EE-Oz website @ http://elt.ee-oz.com.au/content/view/128/265 and on www.training.gov.au 119_eeozRACA4_2b.indd 1
Refrigeration, Air Conditioning and Appliance Servicing Qualifications UEE111 Certificate II in Split Air-conditioning and Heat Pump Systems This qualification covers competencies for the installation, commissioning and de-commissioning of single head, split air conditioning and heat pumps to a prescribed routine where the maximum plant capacity for each system does not exceed 18 kwr. This includes wall hung, floor and ceiling suspended, cassette and ducted fan coil split and water heating heat pump. This qualification excludes competencies required for service, repair, maintenance, diagnostic/fault finding and electrical work or the safe and proper installation of commercial refrigeration, air conditioning and heat pump plant and equipment. UEE211 Certificate II in Electrotechnology (Career Start) This qualification covers competencies for work entry program providing grounding in safety and basic skills and knowledge for work in any electrotechnology discipline. UEE32111 Certificate III in Appliance Service This qualification provides competencies to set-up, service and repair electrical and refrigerated appliances with electives in gas appliances. UEE32211 Certificate III in Air-conditioning and Refrigeration This qualification provides competencies to select components, install, set up, test, fault find, repair and maintain and equipment that apply to food storage and preservation, air conditioning and air distribution equipment in buildings and premises. It includes regulatory requirements for purchasing and handling refrigerants. UEE42711 Certificate IV in Air-conditioning and Refrigeration Servicing This qualification provides competencies in high level fault diagnosis and rectification, commissioning and maintenance of and equipment that apply to commercial food storage and preservation, air-conditioning, air distribution equipment and/or special applications. It includes regulatory requirements for purchasing and handling refrigerants. UEE42811 Certificate IV in Air-conditioning Systems Energy Management and Control This qualification provides competencies to develop strategies for the reduction of energy in buildings and to recommend changes in the way in which energy is controlled in the building either by the installation of new control equipment or by the modification or re-programming of that existing. It includes regulatory requirements for purchasing and handling refrigerants. UEE42911 Certificate IV in Refrigeration and Air-conditioning Systems This qualification provides the competencies to determine heat loads and select equipment for basic commercial refrigeration or residential air conditioning applications. It includes regulatory requirements for purchasing and handling refrigerants. UEE50311 Diploma of Electrical and Refrigeration and Air-conditioning This qualification provides competencies to select, install, commission, maintain and diagnose faults/malfunctions on and equipment that apply to commercial food storage and preservation and air conditioning and air distribution equipment and special applications and associated electrical. It includes ERAC requirements for an Electrician s licence and regulatory requirements for purchasing and handling refrigerants. UEE51111 Diploma of Engineering Technology - Refrigeration and Air-conditioning This qualification provides enabling competencies to develop and select equipment for heating, ventilation, air conditioning and/or. UEE51211 Diploma of Air-conditioning and Refrigeration Engineering This qualification provides competencies to develop, select equipment, and commission, maintain and diagnose faults/malfunctions of and equipment that apply to commercial food storage and preservation and air conditioning and air distribution equipment and special applications. It includes regulatory requirements for purchasing and handling refrigerants. UEE62411 Advanced Diploma of Engineering Technology Air-conditioning and Refrigeration This qualification provides competencies to design and validate/evaluate refrigeration and air conditioning equipment and and provide technical advice/sales. UEE62511 Advanced Diploma of Air-conditioning and Refrigeration Engineering This qualification provides competencies to design and validate/evaluate refrigeration and air conditioning equipment and, manage risk, estimate and manage projects and provide technical advice/sales. It includes regulatory requirements for purchasing and handling refrigerants. It develops competencies in the ethical and responsible application of mathematics, science, engineering techniques, Standards and Codes of Practice, engineering design practices, supervision and management of physical, human and financial resources in Refrigeration and Air Conditioning engineering. The core competencies of this qualification meet the prescribed requirements for Engineering Associate membership of Engineers Australia. 119_eeozRACA4_2b.indd 2
Certificate III in Air-conditioning and Refrigeration National Qualification Number UEE32211 Scope This qualification provides competencies to select components, install, set up, test, fault find, repair and maintain and equipment that apply to food storage and preservation, air conditioning and air distribution equipment in buildings and premises. It includes regulatory requirements for purchasing and handling refrigerants. Note: The Ozone Protection and Synthetic Greenhouse Gas Legislation Amendment Bill 03 apply to this qualification. Prior to planning the delivery of any training and/or assessment activities all legislative and regulatory requirements shall be identified and included. Completion requirements The requirements for granting this qualification will be met when competency is demonstrated and achieved for: All the Core competency standard units, and A combination of Elective competency standard units to achieve a total weighting of 60 points, and All the required pre-requisite competency standard units. Core Competency Standard Units All Core competency standard units to be achieved UEENEEC025B Participate in refrigeration and air conditioning work and competency development activities UEENEEE101A Apply Occupational Health and Safety regulations, codes and practices in the workplace UEENEEE102A Fabricate, assemble and dismantle utilities industry components UEENEEE003B Solve problems in extra-low voltage single path circuits UEENEEE105A Fix and secure electrotechnology equipment UEENEEE107A Use drawings, diagrams, schedules, standards, codes and specifications UEENEEE137A Document and apply measures to control OHS risks associated with electrotechnology work UEENEEJ102A Prepare and connect refrigerant tubing and fittings 30 UEENEEJ103A Establish the basic operating conditions of vapour compression 60 UEENEEJ104A Establish the basic operating conditions of air conditioning UEENEEJ106A Install refrigerant pipe work, flow controls and accessories 60 UEENEEJ107A Install air conditioning and, major components and UEENEEJ108A Recover, pressure test, evacuate, charge and leak test refrigerants 60 UEENEEJ109A Verify functionality and compliance of refrigeration and air conditioning installations UEENEEJ110A Select refrigerant piping, accessories and associated controls 50 UEENEEJ111A Diagnose and rectify faults in air conditioning and and components UEENEEJ113A Commission air conditioning and UEENEEJ153A Find and rectify faults motors and associated controls in refrigeration and air conditioning UEENEEJ170A Diagnose and rectify faults in air conditioning and refrigeration control 70 UEENEEJ194A Solve problems in low voltage refrigeration circuits UEENEEK142A Participate in environmentally sustainable work practices UEENEEP012A Disconnect / reconnect composite appliances connected to low voltage installation wiring UEENEEP017A Locate and rectify faults in low voltage composite appliances using set procedures UEENEEP024A Attach cords and plugs to electrical equipment for connection to a single phase 230 Volt supply UEENEEP025A Attach cords, cables and plugs to electrical equipment for connection to 1000 Va.c. or 1500 Vd.c. supply Total points in core 1000 Weighting points 60 80 50 60 119_eeozRACA4_2b.indd 3
Elective Competency Standard Units Complete Elective units to achieve a total of weighting of 60 points from the following groups: Group A B Imported and Common Elective Units Imported units from other training packages and/or state accredited courses can be added to this group, but they must be selected from qualifications where the unit is first packaged at AQF level 3. If units have not being assigned a weighting in the Electrotechnology Training Package, their weighting will be 10 points. Qualification Electives - Schedule 3 Units You may select all your elective units from this Group Group A Imported and Common Elective Units Minimum points 0 30 30 60 UEENEEC001B Maintain documentation UEENEEC002B Source and purchase material/parts for installation or service jobs UEENEEC003B Provide quotations for installation or service jobs UEENEEC010B Deliver a service to customers UEENEED001B Use basic computer applications relevant to a workplace UEENEEE009B Comply with scheduled and preventative maintenance program processes UEENEEE0B Provide basic instruction in the use of electrotechnology apparatus CPCCOHS1001A Work safely in the construction industry 10 CPCPCM23A Carry out OHS requirements CPCPMS3015A Install and test ducting 10 HLTCPR1B Perform CPR 10 HLTFA301C Apply first aid 10 Imported units from other training packages and/or state accredited courses can be added to this group, but they must be selected from qualifications where the unit is first packaged at AQF level 3. If units have not being assigned a weighting in the Electrotechnology Training Package, their weighting will be 10 points. Note: For further information see Application of NQC Flexibility Formula, UEE11 Electrotechnology Training Package, Version 1, Volume 1 Qualification Framework. Maximum points Weighting Points Up to 30 points 119_eeozRACA4_2b.indd 4
Group B Qualification Electives - Schedule 3 Units You may select all your elective units from this Group Weighting Points UEENEEI150A Develop, enter and verify programs for programmable logic controllers using ladder instruction set 60 UEENEEJ114A Resolve problems in hydronic UEENEEJ115A Resolve problems in beverage dispensers UEENEEJ116A Resolve problems in transport UEENEEJ117A Resolve problems in ultra-low temperature UEENEEJ118A Resolve problems in post mix UEENEEJ119A Resolve problems in ice making UEENEEJ166A Resolve problems in dairy UEENEEJ167A Resolve problems in central plant air conditioning UEENEEJ168A Maintain microbial control of refrigeration and air conditioning UEENEEJ171A Resolve problems in refrigerated beverage vending cabinets UEENEEJ174A Apply safety awareness and legal requirements for hydrocarbon refrigerants 10 UEENEEJ175A Service and repair self contained hydrocarbon air conditioning and refrigeration UEENEEJ176A Install and commission hydrocarbon, components and UEENEEJ178A Apply safety awareness and legal requirements for ammonia refrigerant 10 UEENEEJ179A Repair and service ammonia UEENEEJ180A Install and commission ammonia, components and UEENEEJ182A Repair and service secondary UEENEEJ184A Apply safety awareness and legal requirements for carbon dioxide refrigerant 10 UEENEEJ185A Repair and service carbon dioxide UEENEEJ186A Install and commission carbon dioxide, components and UEENEEJ188A Repair and service self contained carbon dioxide refrigeration and heat pump UEENEEJ196A Operate ammonia refrigeration plant Note: 1. Pre-requisite pathways shall be identified and met for all elective units selected. 2. In selecting elective units considerations to career planning advice should be given to units that form part of a pre-requisite pathway for the progression to achieve particular competencies or qualification at a higher level. END OF QUALIFICATION 119_eeozRACA4_2b.indd 5
Refrigeration, Air Conditioning and Appliance Servicing Skill Sets Design Ammonia Refrigeration Systems Design Complex Carbon Dioxide Refrigeration Install and Commission Ammonia Refrigeration Systems Systems Install and Commission Carbon Dioxide Refrigeration Operate Ammonia Refrigeration Plant Systems Service and Repair Ammonia Refrigeration Systems Service and Repair Carbon Dioxide Refrigeration and Heat Pump Systems Service and Repair Carbon Dioxide Refrigeration Systems Design Hydrocarbon Refrigeration Systems Install and Commission Hydrocarbon Refrigeration Systems, Major Components and Associated Equipment Service and Repair Hydrocarbon Refrigeration and Air Conditioning Systems Design Secondary Refrigeration Systems Service and Repair Secondary Refrigeration Systems Refrigeration, Air Conditioning and Appliance Servicing Competency Standard Units UEENEEJ0B Manage refrigeration and air conditioning projects UEENEEJ0B Manage refrigeration and air conditioning projects UEENEEJ069B UEENEEJ103A UEENEEJ105A UEENEEJ107A UEENEEJ109A UEENEEJ111A UEENEEJ113A UEENEEJ115A UEENEEJ117A Plan refrigeration and air conditioning projects Establish the basic operating conditions of vapour compression Position, assemble and start up single head split air conditioning and water heating heat pump Install air conditioning and refrigeration, major components and Verify functionality and compliance of refrigeration and air conditioning installations Diagnose and rectify faults in air conditioning and and components Commission air conditioning and Resolve problems in beverage dispensers Resolve problems in ultra-low temperature UEENEEJ102A UEENEEJ104A UEENEEJ106A UEENEEJ108A UEENEEJ110A UEENEEJ112A UEENEEJ114A UEENEEJ116A UEENEEJ118A Prepare and connect refrigerant tubing and fittings Establish the basic operating conditions of air conditioning Install refrigerant pipe work, flow controls and accessories Recover, pressure test, evacuate, charge and leak test refrigerants Select refrigerant piping, accessories and associated controls Diagnose and rectify faults in complex air conditioning/ Resolve problems in hydronic Resolve problems in transport Resolve problems in post mix UEENEEJ119A Resolve problems in ice making UEENEEJ121A Monitor and adjust refrigeration energy management UEENEEJ122A Diagnose faults in complex HVAC / refrigeration control UEENEEJ124A Commission refrigeration/ air conditioning hydronic UEENEEJ126A Commission complex refrigeration/air conditioning control UEENEEJ128A UEENEEJ130A UEENEEJ132A UEENEEJ134A UEENEEJ136A Produce HVAC/R system design drawings Produce HVAC/R control system diagrams Design commercial refrigeration and select components Design heating, ventilation and air conditioning (HVAC) and select components Evaluate and report on building services energy management UEENEEJ123A UEENEEJ125A UEENEEJ127A UEENEEJ129A UEENEEJ131A UEENEEJ133A UEENEEJ135A UEENEEJ137A Commission complex (HVAC) heating, ventilation and air conditioning Commission complex refrigeration and equipment Establish the thermodynamic parameters of refrigeration and air conditioning Establish heat loads for commercial refrigeration and/or air conditioning applications Determine noise and vibration encountered in HVAC/R applications Design industrial and select components Design control for refrigeration or heating, ventilation and air conditioning Evaluate and report on the indoor air quality of buildings 119_eeozRACA4_2b.indd 6
Refrigeration, Air Conditioning and Appliance Servicing Competency Standard Units UEENEEJ138A Analyse vibration and noise in refrigeration and air conditioning UEENEEJ139A Develop specifications and prepare drawings for HVAC/Refrigeration projects UEENEEJ141A UEENEEJ143A UEENEEJ145A UEENEEJ147A UEENEEJ149A UEENEEJ151A UEENEEJ154A UEENEEJ156A Design complex commercial and select equipment Design complex air conditioning and select equipment Design hydronic and select equipment Audit energy use for commercial HVAC/Refrigeration Develop heat exchanger design specifications Service small electrical appliances and power tools Find and rectify faults in appliance control and devices Service clothes washing machines and dryers UEENEEJ142A UEENEEJ144A UEENEEJ146A UEENEEJ148A UEENEEJ150A UEENEEJ153A UEENEEJ155A UEENEEJ157A Design complex industrial refrigeration and select equipment Design mechanical ventilation/exhaust and select equipment Design complex control for refrigeration, heating ventilation or air conditioning Audit HVAC/R control for compliance with regulations and standards Evaluate new and alternative technologies applicable to electrotechnology applications Find and rectify faults motors and associated controls in refrigeration and air conditioning Service refrigeration appliances Service electrical heating appliances UEENEEJ158A Service dishwasher machines UEENEEJ159A Service gas heating appliances UEENEEJ161A Verify functionality and compliance of appliances UEENEEJ162A Recover, pressure test, evacuate, charge and leak test refrigerants appliances UEENEEJ164A UEENEEJ166A UEENEEJ168A UEENEEJ171A Analyse the operation of HVAC air and hydronic Resolve problems in dairy Maintain microbial control of refrigeration and air conditioning Resolve problems in refrigerated beverage vending cabinets UEENEEJ165A UEENEEJ167A UEENEEJ170A UEENEEJ172A Evaluate thermodynamic and fluid parameters of Resolve problems in central plant air conditioning Diagnose and rectify faults in air conditioning and refrigeration control Recover, pressure test, evacuate, charge and leak test refrigerants split UEENEEJ173A Service and repair microwave ovens UEENEEJ174A Apply safety awareness and legal requirements for hydrocarbon refrigerants UEENEEJ175A UEENEEJ177A UEENEEJ179A Service and repair self contained hydrocarbon air conditioning and Design hydrocarbon refrigerated Repair and service ammonia UEENEEJ176A UEENEEJ178A UEENEEJ180A Install and commission hydrocarbon, components and Apply safety awareness and legal requirements for ammonia refrigerant Install and commission ammonia, components and UEENEEJ181A Design ammonia refrigerated UEENEEJ182A Repair and service secondary UEENEEJ183A Design secondary refrigerant UEENEEJ184A Apply safety awareness and legal requirements for carbon dioxide refrigerant UEENEEJ185A UEENEEJ188A Repair and service carbon dioxide Repair and service self contained carbon dioxide refrigeration and heat pump UEENEEJ186A UEENEEJ189A Install and commission carbon dioxide, components and Service room air conditioners 119_eeozRACA4_2b.indd 7
Refrigeration, Air Conditioning and Appliance Servicing Competency Standard Units UEENEEJ190A Select basic commercial refrigeration system equipment, components and accessories UEENEEJ191A Select residential air conditioning system equipment, components and accessories UEENEEJ192A UEENEEJ194A UEENEEJ196A Analyse the psychrometric performance of HVAC/R Solve problems in low voltage refrigeration circuits Operate Ammonia Refrigeration Plant UEENEEJ193A UEENEEJ195A Analyse the thermodynamic performance of HVAC/R Establish the basic operating conditions of vapour compression appliances ABOUT EE-Oz Training Standards EE-Oz Training Standards is the Australian Government declared Industry Skills Council for the Australian ElectroComms and EnergyUtilities Industries. EE-Oz Training Standards has primary responsibillty for developing and maintaining Training Packages for the industries under its coverage. These include the Electrotechnology, Gas, Electricity Supply Industry - Transmission, Distribution and Rail and the Electricity Supply Industry - Generation Training Packages. The Refrigeration, Air Conditioning and Appliance Servicing are part of the Electrotechnology industry. Contact Details * PO Box 12 Dickson ACT 2602 + Unit 2, 48 Mort Street, Braddon ACT 2612 8 ee-oz@ee-oz.com.au : ee-oz.com.au ) 02 6262 7055 7 02 6257 4222 August 12 119_eeozRACA4_2b.indd 8