Risk Assessment for Use of Alcohol-Based Hand Rubs in Healthcare Facilities



Similar documents
Hazard/Risk Identification and Control Procedure

MATERIAL SAFETY DATA SHEET DATE: 2009, revised July 2011 PRODUCT NAME: BOSTON BRAKE & PARTS CLEANER PRODUCT CODE: 78200

PRODUCT SAFETY DATA SHEET According to 91/155 EC 1. IDENTIFICATION OF THE SUBSTANCE / PREPARATION AND OF THE COMPANY / UNDERTAKING

Material Safety Data Sheet

This guide is prepared by the Occupational Safety and Health Branch, Labour Department. This edition March 2010

Date: 22 June 2005 Version: 2 Revision: Identification of the substance/preparation and company/undertaking

Material Safety Data Sheet

MATERIAL SAFETY DATA SHEET. PRODUCT NAME: BOSTON AEROSOL ENAMEL PAINT PRODUCT CODE: BT dependant on colour

SAFETY SIGNAGE PROCEDURE

FLAMMABLE LIQUIDS COMPLIANCE NOTE

MATERIAL SAFETY DATA SHEET OF EPOXY ESTER KU 95 1/5

Safety Data Sheet Steam Cylinder Oil C 460

Technical Data Sheet

SECTION 1 - PRODUCT IDENTIFICATION

MATERIAL SAFETY DATA SHEET

Laboratory Work Risk Assessment

JOINT CBA AND SIA GUIDANCE FOR THE STORAGE OF FLAMMABLE LIQUIDS IN SEALED PACKAGES IN SPECIFIED EXTERNAL STORAGE AREAS

SAFETY DATA SHEET Sorex Wasp Nest Destroyer MK II

SAFETY DATA SHEET BOSTIK AQUAGRIP 536

February 2014 Alberta Fire Code Page 1 of 5. Fire Safety and Hand Hygiene in Healthcare Facilities

Material Safety Data Sheet

REVISION NO : 3 August 2010

Wilkins Safety Group

WORKING IN ISOLATION PROCEDURE

Mechanical Systems Competency 1.20

Material Safety Data Sheet

SAFETY DATA SHEET. Trade name: Master Clear Seal-5 Revised: 5/29/2015

CONFINED SPACE PROCEDURE

Material Safety Data Sheet

Beware that ordinary prescription glasses do not provide adequate protection. This is also true with poorly fitting safety glasses.

SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING. Enzymatic Drain Cleaner and Maintainer

SAFETY DATA SHEET LIGHT NEUTRAL BASE OIL

In addition, flammable solvents and thinners are often mixed with the above substances.

Sample Written Program. For. Flammable Liquids

Manufacturer/supplier information. Street/postbox: P.O. Box 15408

Title: OHS Risk Management Procedure

6 STEPS TO RISK MANAGEMENT

MATERIAL SAFETY DATA SHEET

CHEMICAL SPILL MANAGEMENT GUIDELINES

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING.

SITE CONTRACTOR PROCEDURES

Vita (Europe) Limited. Corresponding to EC Directive 93/112/EC. Date Issued: 08 March 2006 Replaces Version of: 15 November 2001

Ingredient % content Hazard data Cross linked Sodium Polyacrylite CAS No: Non chemical fillers Zeolite 1-10

Trade Name of this Product Isopropyl Rubbing Alcohol 91% USP. Corporate Compliance Team 1666 East Touhy Avenue

Presented by: Rich Perry Marsh Risk Consulting

HAZARDOUS MATERIALS MANAGEMENT ISSUE 2

OFF! DEEP WOODS SPORTSMEN INSECT REPELLENT I (PUMP SPRAY)

SAFETY DATA SHEET CAM SUYU ANTIFRIZI

SAFETY DATA SHEET. according to 1907/2006/EC, Article 31 CYTOFIXX (CYTOLOGICAL FIXATIVE)

Hazard Identification, Risk Assessment and Control Procedure

: GLADE Aerosol - Lavender

SAFETY DATA SHEET EVO-STIK PLUMBERS MAIT

WINDEX ORIGINAL GLASS CLEANER

Swallowed Do not induce vomiting give 250 ml water to drink. Seek immediate medical attention.

SDS. GHS Safety Data Sheet. Wechem, Inc. Extract All PRODUCT AND COMPANY IDENTIFICATION. Manufacturer HAZARDS IDENTIFICATION

SAFETY DATA SHEET INSTANT HAND SANITIZER GEL / SANTI-GEL

Standard Operating Procedure

Material Safety Data Sheets (MSDS), Spill Clean-Up

No. Name of Legislation Applicable Issues and Requirements Demonstration of Compliance 1. Health and Safety at Work Act 1974

Independent Forensics of Illinois

Risk Assessment Tool (example only)

Section 1 - Identification of The Material and Supplier

MATERIAL SAFETY DATA SHEET TOILET BOWL SANITIZER

SAFETY DATA SHEET BLUECOL SCREENWASH

Safety Data Sheet. according to WHMIS. SECTION 1: Identification of the substance/mixture and of the company/undertaking

MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET

: WOLF RADIATOR SEALER & CONDITIONER

BiO-STiX Drain Cleaner & Deodorizer

NFPA Hazard Class: * Physical Form: Solid. Health: 0 (Least) * Appearance: Yellow Flammability: 1 (Slight)

SAFETY DATA SHEET. according to 1907/2006/EC, Article 31. Zenith 2B Machine Rinse Aid (020000, )

Material Safety Data Sheet

Guidance sheet 4: Chemical Spill Management

SAFETY DATA SHEET DOUBLE TT MAINTENANCE SPRAY

Current version : 2.0.1, issued: Replaced version: 2.0.0, issued: Region: GB

Installation Instructions for Alarm Module Kit A043F059

SAFETY DATA SHEET BLOOD & PROTEIN REMOVER

SAFETY DATA SHEET Knock Out Drain Cleaner

The EU-GHS Hazard statements in English (Precautionary statements: from page 5)

SAFETY DATA SHEET TIDYFOAM E2 HAND CLEANER SANITIZER

SAFETY DATA SHEET BLUE STAR DE-ICER AEROSOL

Risk Management Program March 2015

MATERIAL SAFETY DATA SHEET

CHAPTER 12 Occupational Safety & Health and Environmental Protection Programs

SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING SULPHURIC ACID DRAIN CLEANER

Hazard Identification, Risk Assessment And Control Procedure

Risk management a practical approach

SAFETY DATA SHEET BENZOIN TINCTURE

Version 1. Print Date 12/01/2009 Revision Date 11/30/2009 MSDS Number SITE_FORM Number

WORKING IN CONFINED SPACES GUIDELINES

SAFETY DATA SHEET LIQUITEX PROFESSIONAL SPRAY PAINT

AXIRON (AXE-e-RON) CIII

SAFETY DATA SHEET BUTANE CARTRIDGE

Autofoam SAFETY DATA SHEET

CLEANING AND SANITIZING

SAFETY DATA SHEET Sterling Label Remover LS184

Six steps to Occupational Health and Safety

Elements of an Occupational Health and Safety Program

Transcription:

Introduction Improving hand hygiene among healthcare workers (HCW) is currently the single most effective intervention to reduce the risk of hospital-acquired infections in Australian hospitals. One way in which HCWs improve their hand hygiene practices is through the regular use of alcohol-based hand rubs at the point-of-care. There are a number of risks to patients and staff associated with the use of alcohol hand rub, however the benefits in terms of its use far outweigh the risks. Risk assessment should be undertaken and a management plan put in place. This particularly applies to clinical areas managing patients with alcohol use disorder and patients at risk of deliberate self harm. The Risk Assessment below is provided as a generic guide and includes common issues that need to be addressed in all healthcare facilities. Use of this Risk Assessment may assist in addressing these issues to ensure appropriate use and placement of alcohol-based hand rubs at the point-of-care. Risk Assessment Worksheet Task Date assessed January 2009 Storage & use of generic alcohol based hand rubs (ABHR) Risk Assessment Completed by: HHA Team Potential Hazards Splash Unlikely Likelihood (Rare/Almost Certain?) Consequence (What can happen?) Minor/moderate Risk Rating (Inherent) Risk Treatment Risk Rating (Residual) Considered unlikely during normal use. Minor injury Irritation of eyes Moderate Corneal damage (refer to WHO Guidelines 1 ) Engineering: Design and placement of hand dispensers minimises the risk of a splash incident. Consider: Metered dose dispenser Splash/drip tray Appropriate dispenser locations, (i.e. dispensers can be mounted on walls out of the reach of children or in supervised locations. Refer HHA manual Appendix 3). Avoid placing at eye level Do not place on head of bed Maximum bottle size of 500mL, no decanting of bottles is allowed Page 1 of 9

Administrative: Education educate staff on safe use and handling of ABHR. Comments If a splash occurs don t rub, flush eye and seek help ASAP. Ingestion Unlikely Minor/Moderate Considered unlikely during normal use. Alcohol Toxicity Minor - Intoxication Signs include: headache, dizziness, lack of coordination, hypoglycaemia, abdominal pain, nausea, vomiting and haematemesis Moderate Severe toxicity Signs include: respiratory depression, hypotension, and coma. (refer to WHO Guidelines 1 ) Substitution: Engineering: Design of hand dispensers minimises the risk of accidental ingestion. Careful consideration for placement of ABHR in mental health facilities, and alcohol withdrawal units. Instead of ABHR being mounted in rooms, staff could be issued personal pocket bottles instead Also consider Lockable dispenser holders Metered dose bottles Labelling dispensers to make the alcohol content less clear at a casual glance Adding a warning label against consumption Inclusion of an additive in the product formula to make it unpalatable Appropriate dispenser locations, (i.e. dispensers can be mounted on walls out of the reach of children or in supervised locations. Refer HHA manual Appendix 3). Administrative: Educate staff on correct use/handling of ABHR. Ensure all ABHR containers are appropriately labelled. Page 2 of 9

Fire Possible Moderate Medium Considered unlikely during normal use. Burns to person Damage to property Incidents involving fire and ABHR have been reported, however the incidence is extremely low (refer to articles by Kramer 2 and Boyce 3 ) Engineering: Ensure appropriate safety (fire fighting) equipment is in use (i.e. smoke alarms, sprinkler systems, extinguishers etc. Ensure appropriate dispenser locations, (i.e. dispensers should be mounted on walls out of the reach of children, in supervised locations, and in areas fitted with working sprinklers) (Refer HHA manual Appendix 3). Administrative: Do not store or use hand rubs near open flames or ignition sources. No smoking should be permitted in these areas. Ensure appropriate emergency procedures are in place and communicated to all staff. Educate staff on correct use/handling ABHR to rub hands together until alcohol has evaporated and hands are dry before moving on to another activity. (i.e. not to smoke immediately after decontaminating hands.) Comments The overall risk of fires associated with ABHR is extremely low Consult MSDS, local OH&S requirements & HHA guidelines for product placement. Consult local fire standards Spillage / Splash onto Floor Possible/Likely Considered likely with solution Insignificant / Minor Insignificant discoloration of floor surfaces / Medium Unlikely but possible with a gel Minor potential for a slip hazard Engineering: Design of hand dispensers minimises the risk of spillage by having a drip tray underneath Page 3 of 9

Administrative: Ensuring staff use both hands to dispense ABHR, and that spills are cleaned up immediately. Educate staff that 1-2 pumps from dispenser will release an appropriate amount of ABHR, and that excessive pumping is not required. Deliberate or unintentional misuse Possible Potential for deliberately or unintentional misuse of ABHR (i.e. children or the mentally ill). Moderate (refer to splash, ingestion, flammability) Medium Engineering: Design of hand dispensers minimises the risk of a splash injury. Consider: Dispenser locations, (i.e. dispensers can be mounted on walls out of the reach of small children or in supervised locations) Administrative: Do not store or use hand rubs near open flames or ignition sources. Consider: Education - Correct use of hand rub/potential hazards Alcohol Absorption Concern of skin absorption for religious or other reasons Unlikely ABHR with isopropanol appears more predictable in its lack of cutaneous alcohol absorption when compared with an ethanol-based ABHR 1 Insignificant Local studies have demonstrated minimal rates of cutaneous alcohol absorption. Engineering: N/A Administrative: N/A Page 4 of 9

Bulk Storage of ABHR (Dangerous Goods Class 3 - Flammable liquid) Intense use of an ethanol based ABHR has shown blood ethanol concentrations were far below levels that would result in noticeable symptoms (Kramer ref 787 in new WHO) Rare You cannot absorb enough through your skin to lose you drivers license (refer to article by Brown 4 ) Moderate (fire hazard) Burns to person Damage to property Incidents involving fire and ABHR have been reported, however the incidence is extremely low (refer to articles by Kramer 2 and Boyce 3 ) Engineering: Ensure that bulk storage complies with state fire regulations and apply standard precautions for flammable liquids (DG class 3): Store in a cool, well ventilated environment away from flammable gases, explosives, oxidising agents, halogens, aldehydes, foodstuff and sources of heat or ignition. A designated flame proof cabinet will be required for situations where it is necessary to store more than 50L The storage of ABHR in a ward or department should be kept to a minimum (as is reasonably practicable) for day-to-day purposes only. Administrative: N/A Disposal Rare Minor Engineering: used containers will contain residue and flammable vapours rinsing out used containers with copious amounts of cold water will reduce the risk of fire and the containers may then be recycled (but not reused) or disposed of in general waste (ref new WHO) Page 5 of 9

Administrative: Ensure staff know the correct procedures for disposal of ABHR bottles Skin Irritation Rare Minor Substitution: Trial alternative HH products. Engineering: Ensure a compatible skin moisturiser is readily available for all hospital staff in all areas Administrative: Ensure part of the HH education package includes advice on moisturising a minimum of 3 times a shift Ensure that there is procedure for staff to report skin irritations for assessment and treatment. Infection from poor compliance with HH product regimes Almost Certain On baseline HH compliance audits 7-20% compliance is normal Major-Severe HH compliance is associated with higher HCAIs (refer to WHO Guidelines 1 ) Extreme! Engineering: Ensure ABHR products are widely available with easy and unobstructed access and logical placement. Medium Ensure appropriate logistics of regular procurement and replenishment of consumables Administrative: Ensure hospital wide education program on HH and correct use of HH products PPE: Appropriate use of ABHR when working with patients Page 6 of 9

References 1. World Alliance for Patient Safety. Who Guidelines on Hand Hygiene in Healthcare (Advanced Draft): Global patient safety challenge 2005-2006: Clean care is safer care. World Health Organisation; 2005. 2. Kramer A, Kampf G. Hand rub-associated fire incidents during 25,038 hospital years in Germany. Infection control and epidemiology 2007;28(6):745-746. 3. Boyce JM, Pearson ML. frequency of fires from alcohol hand rub dispensers in health care facilities. Infection control and hospital epidemiology 2003;24:618-619. 4. Brown TL, Gamon S, Tester P, Martin R, Hosking K, Bowkett GC, Gerostamoulos D, O Brien M, Grayson ML. Can alcohol-based hand-rub solutions cause you to lose your driver s licence? Comparative cutaneous absorption of various alcohols. Antimicrobial Agents Chemotherapy 2007; 51:1107-8. Page 7 of 9

5. Risk Consequence, Likelihood & Matrix Tables: Adapted from the Risk Management Standard AS/NZS 4360: 2004 Table 1 Consequence Table 2 Likelihood Level Descriptor Examples of Description 1 Insignificant Injuries not requiring first aid. 2 Minor First aid required (only), minor property damage 3 Moderate Medical treatment required, moderate damage to property 4 Major Hospital admission required, major damage to property 5 Severe Death or permanent disability to one or more persons, total loss of property. Level Descriptor Examples of Description A Almost certain The event is expected to occur in most circumstances. B Likely The event will probably occur in most circumstances. C Possible The event could occur at some time. D Unlikely The event is not likely to occur in normal circumstances. E Rare The event may occur only in exceptional circumstances. Table 3 Risk Rating Matrix Likelihood Consequence Insignificant Minor Moderate Major Severe Almost certain Medium High Extreme Extreme Extreme Likely Medium High Extreme Extreme Possible Medium High Extreme Unlikely Medium High Rare Medium Page 8 of 9

Hierarchy of Risk Controls The risks must be minimised to the lowest reasonably practicable level by taking the following measures in the following order and as determined by the risk assessment. Elimination Substitution Engineering controls Administrative controls Personal Protective Equipment The job is redesigned so as to remove the hazard. However, the alternative method should not lead to a less acceptable product or less effective process. Replace the material or process with a less hazardous one. For example, replace mercury thermometers with spirit thermometers. Install or using additional machinery such as local exhaust ventilation to control the risk. Separating the hazard from operators by methods such as enclosing or guarding dangerous items of machinery. Reduce the time the worker is exposed to the hazard. Provide training. Perform risk assessments. Increase safety awareness signage. Only after all the previous measures have been tried and found to be ineffective in controlling the risks should Personal Protective Equipment be considered. If chosen, PPE should be selected and fitted to the person who uses it. Workers must be trained in the function and limitation of each item of PPE. For example, an operator should know how long the compressed supply in a self contained breathing apparatus will last. PPE may be used as a temporary control measure until other alternatives are installed. In most cases a combination of engineering controls, administrative controls and PPE are chosen to effectively control the risks. Page 9 of 9