Cisco 3600 Series Gateway-PBX Interoperability: Lucent Definity G3 with E1 R2 Signaling This document describes the interoperability and configuration of a Cisco3600 series voice gateway with a Lucent Definity G3 PBX using E1 R2 signaling. It includes the following sections: System Components Configuration Tasks Caveats System Components PBX Model Lucent DEFINITY G3 PBX Release G3V7i.01.0.343.7 Telephony Signaling E1 R2 Voice Gateway Cisco 3640 Gateway Release Cisco IOS TM 12.1.2XH VoX Protocol H.323 Configuration Tasks See the following sections for configuration tasks for this feature: Set Up Lucent PBX Configuration Cisco 3640 Gateway Configuration Page 1
Set Up This section includes the following information: Connectivity Diagrams Set Up Notes Connectivity Diagrams Figure 1: Test Configuration Figure 1 represents the configuration used for testing: a Lucent Definity G3 PBX connected to a Cisco 3640 voice gateway via an E1 R2 connection. Set Up Notes Lucent Definity G3 has no provision for the E1 interface to receive a clock. Because it always wants to provide clock on the interface, the Cisco 3640 E1 interface must be set to line clock to work with it. Lucent Definity G3 uses the same TN464F DS1 INTFC 24/32 card for both T1 and E1 trunking. To select E1 functionality, some database entries are made in the Lucent trunk configuration screen, and there are two DIP switches on the card itself: o 24CH/30CH Set to 24CH for T1, 30CH for E1. o 120Ω/75Ω -- Set to 120Ω to use with a twisted pair E1 circuit. If set to 75Ω to use with a coaxial wire E1 circuit, an external adapter provided by Lucent must be used. Lucent DEFINITY G3 PBX does not support R2-Digital Line Signaling (ITU-T Q.421). It supports R2-Analog version (ITU-T Q.411). Lucent DEFINITY G3 PBX has specific country settings for the R2 forward and backward multifrequency combinations. For each country specific settings, refer to: DEFINITY Enterprise communications Server Manual Application Notes for Type Approval Comcode 108343302 Issue 1 June 1999 Page 2
Table 1 summarizes E1 R2 country variant setting on both the Lucent Definity PBX and the Cisco 3640 gateway. Table 1: Country Variant Settings LUCENT V7 SETTING # 3640 SETTING COMMENTS Country Code 16 parameters. 1 country Argentina send-ani signal must be defined as A-5 tone for incoming backward signal types in Lucent MF-signaling-related Sys. Param. Country Code 2 Country Code 1 parameters. 2 Country Code 16 parameters. 3 Country Code 1 Chile parameters. 4 country Australia country Bolivia country Brazil country ITU 5 Australia on Lucent PBX free signal must be defined as B-6 (not B-1) tone for incoming backward signal types in Lucent MF-signaling-related Sys. Param. Country code 16 is used for Brazil per Lucent Application Notes for Type Approval free signal must be defined as B-6 (not B-1) tone for incoming backward signal types in Lucent MF-signaling-related Sys. Param. for Chile Country Code 14 parameters. 6 Country Code 18 parameters. 7 Country Code 1 parameters. 8 country Bulgaria country China country Costa Rica Use Lucent MF-signaling-related Sys. Param. for Czech Repulic Country code 1 is used for Costa Rica per Lucent Application Notes for Type Approval # Refer to Lucent s Application Notes for Type Approval, Comcode 108343302 document, Issue 1, for details on MF-signaling-related System Parameters. 1 Refer to page 29 for details on MF-signaling-related System Parameters for Argentina. 2 Refer to page 60, for details on MF-signaling-related System Parameters for Bolivia. 3 Refer to page 73, for details on MF-signaling-related System Parameters for Brazil. 4 Refer to page 93, for details on MF-signaling-related System Parameters for Chile. 5 3640 router does not have country option for Chile. Use ITU defaults. 6 Refer to page 141, for details on MF-signaling-related System Parameters for Bulgaria. 7 Refer to page 110, for details on MF-signaling-related System Parameters for China. 8 Refer to page 124, for details on MF-signaling-related System Parameters for Costa Rica. Page 3
Country Code 14 parameters. 9 Country Code 17 Country Code 19 Country Code 1 parameters. 10 Country Code 13 parameters. 11 Country Code 2 country Croatia country Ecuador country Greece country Guatemala country Hong-Kong-China country India country Indonesia country Israel country ITU country Korea country Laos country Malaysia country Malta country New Zealand country Paraguay Use Lucent MF-signaling-related Sys. Param. for Czech Repulic Call is completed after ~19 seconds delay from end of signaling. Ecuador on Lucent PBX Greece on Lucent PBX Guatemala on Lucent PBX Hong Kong on Lucent PBX Country code 1 is used for India per Lucent Application Notes for Type Approval Indonesia on Lucent PBX Israel on Lucent PBX Used Lucent MF-signalingrelated Sys. Param. for Argentina (ITU variant) Korea on Lucent PBX Laos on Lucent PBX Malaysia on Lucent PBX Malta on Lucent PBX New Zealand on Lucent PBX Paraguay on Lucent PBX 9 Refer to page 141, for details on MF-signaling-related System Parameters for Croatia. 10 Refer to page 254, for details on MF-signaling-related System Parameters for India. 11 Refer to page 29 for details on MF-signaling-related System Parameters for Argentina. Page 4
Country Code 9 parameters. 12 Country Code 6 parameters. 13 Country Code 13 parameters. 14 Country Code 7 parameters. 15 Country Code 7 parameters. 16 Country Code 20 country Peru country Philippines country Saudi Arabia country Singapore country South Africa country Telmex Corporation (Mexico) country Telnor Corporation (Mexico) country Thailand country Uruguay country Venzuela country Vietnam Peru on Lucent PBX Philippines on Lucent PBX Used Lucent MF-signalingrelated Sys. Param. for Mexico Used Lucent MF-signalingrelated Sys. Param. for Mexico Thailand on Lucent PBX Uruguay on Lucent PBX Venzuela on Lucent PBX Vietnam on Lucent PBX 12 Refer to page 370 for details on MF-signaling-related System Parameters for Saudi Arabia. 13 Refer to page 378, for details on MF-signaling-related System Parameters for Singapore. 14 Refer to page 407, for details on MF-signaling-related System Parameters for South Africa. 15 Refer to page 313, for details on MF-signaling-related System Parameters for Mexico. 16 Refer to page 313, for details on MF-signaling-related System Parameters for Mexico. Page 5
Lucent PBX Configuration PBX Version Information G3V7i.01.0.343.7 Sample PBX Configuration See the following figures for sample PBX configuration: Figure 2: Country Code Argentina Figure 3: Dial Plan Record Figure 4: Pattern Number Figure 5: Signaling-Related System Parameters Figure 6: Signaling-Related System Parameters II Figure 7: Signaling-Related Parameters III Figure 8: Signaling-Related Parameters IV Figure 9: Trunk Group Figure 10: Trunk Features Figure 11: Trunk Group II Figure 12: ATMS Thresholds Figure 13: Trunk Group III Page 6
Figure 2: Country Code Argentina Page 7
Figure 3: Dial Plan Record Page 8
Figure 4: Pattern Number Page 9
Figure 5: Signaling-Related System Parameters Page 10
Figure 6: Signaling-Related System Parameters II Page 11
Figure 7: Signaling-Related Parameters III Page 12
Figure 8: Signaling-Related Parameters IV Page 13
Figure 9: Trunk Group Page 14
Figure 10: Trunk Features Page 15
Figure 11: Trunk Group II Page 16
Figure 12: ATMS Thresholds Page 17
Figure 13: Trunk Group III Cisco 3640 Gateway Configuration The following is the configuration of the Cisco 3640 gateway connected to the Lucent Definity G3 PBX E1 R2 interface. Cisco 3640 Voice Gateway Version Information Cisco_3640# show version Cisco Internetwork Operating System Software IOS (tm) 3600 Software (C3640-JS-M), Experimental Version 12.1(20000530:031732) [liha-v121_2_xd_throttle.latest 104] Copyright (c) 1986-2000 by cisco Systems, Inc. Compiled Tue 30-May-00 08:18 by liha Image text-base: 0x600088F0, data-base: 0x61444000 ROM: System Bootstrap, Version 11.1(19)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc 1) Cisco_3640 uptime is 4 days, 7 hours, 35 minutes System returned to ROM by power-on System image file is "flash:c3640-js-mz" cisco 3640 (R4700) processor (revision 0x00) with 60416K/5120K bytes of memory. Page 18
Processor board ID 09195735 R4700 CPU at 100Mhz, Implementation 33, Rev 1.0 Channelized E1, Version 1.0. Bridging software. X.25 software, Version 3.0.0. SuperLAT software (copyright 1990 by Meridian Technology Corp). TN3270 Emulation software. Primary Rate ISDN software, Version 1.1. 2 Ethernet/IEEE 802.3 interface(s) 2 Channelized E1/PRI port(s) 2 Voice FXO interface(s) 2 Voice FXS interface(s) DRAM configuration is 64 bits wide with parity disabled. 125K bytes of non-volatile configuration memory. 16384K bytes of processor board System flash (Read/Write) Configuration register is 0x0 Cisco 3640 Voice Gateway Sample Configuration Cisco_3640# show configuration Using 1338 out of 129016 bytes version 12.1 service timestamps debug uptime service timestamps log uptime no service password-encryption no service dhcp hostname Cisco_3640 voice-card 1 ip subnet-zero no ip domain-lookup ip host whiz 171.69.1.162 ip host dirt 171.69.1.129 ip host danube 171.69.17.14 lane client flush isdn voice-call-failure 0 cns event-service server controller E1 1/0 controller E1 1/1 framing NO-CRC4 ds0-group 1 timeslots 1 type r2-analog r2-compelled ani cas-custom 1 country argentina use-defaults metering interface Ethernet0/0 ip address 192.168.71.6 255.255.255.0 no ip mroute-cache no cdp enable interface Ethernet0/1 ip address 100.100.100.2 255.255.255.0 Page 19
no ip mroute-cache no cdp enable ip classless no ip http server no cdp run voice-port 1/1:1 no modem passthrough voice-port 2/0/0 voice-port 2/0/1 voice-port 2/1/0 voice-port 2/1/1 dial-peer voice 1 pots destination-pattern 9000 port 2/0/0 dial-peer voice 4 voip destination-pattern 2... session target ipv4:100.100.100.1 dial-peer voice 2 pots destination-pattern 4... direct-inward-dial port 1/1:1 prefix 4 dial-peer voice 7 voip destination-pattern 5... session target ipv4:100.100.100.1 line con 0 transport input none line aux 0 line vty 0 4 no login end Caveats Lucent Definity G3 PBX does not support R2-Digital Line Signaling (ITU-T Q.421). It supports R2-Analog version (ITU-T Q.411). Page 20