Can Extending Ethernet, GigE, DS1 and DS3 Service Be This Easy? Yes. It can. Enable Ethernet, Gigabit Ethernet, DS3, DS1 Services Each Pulsecom access module is self-contained and functionally optimized for the service you want, without high-cost systems, common cards or provisioning steps. As your customers needs grow, so can your service. Simply add or switch out modules. Simplify Installation and Turn-up Installation and turn-up can be completed in minutes with Pulsecom s Optionless SONET (patent pending) technology and extensive mounting options. Modules can plug directly into Industry Standard shelves or in racks, locking wall enclosures or outdoor pole-mounted cabinets. Extend Range of Services and Facility Capacity Pulsecom s access modules allow you to extend services up a riser, across a campus, across a metro area or across the country. Integrated CWDM and DWDM optics are available to boost capacity without increasing facility costs.
10/100Mb Ethernet OC3 1 x STS3c OE Ethernet cell site service Metro Ethernet Dedicated internet access VoIP Network Interface Device (NID) O3-4D1A/O3-12D1 DS1 cell site service DS1 business service Building/campus extensions Network Interface Device (NID) 1 to 12 DS1s CO/PoP CO/PoP OC3 VT1.5 CO/PoP Ethernet DS1s GigE GigE G2HC Network links High-speed LAN extensions Drop-and-continue rings Network Interface Device (NID) OC48 21 STS1s 4 copper pairs GigE GigE DS3 CO/PoP NETWORK Remote Terminal with SONET mux OC3 STS-1 D3-28D1/D3-14D1 DS1 service 3/1 cross-connect Used alone or with O3-3D3 optical transport 1 to 14 DS1s or 1 to 28 DS1s DS3 DS3-EXPRESS DS3 business service Building/campus extensions DS3 extensions from a fiber ring DS3 cell site service Router access Network Interface Device (NID) 1 to 3 DS3s O3-3D3/O3D3-MO DS3 cell site service DS3 business service Virtual coax across campus or intra-building Drop-and-continue rings Router access Network Interface Device (NID)
Your Choice Existing systems are a great fit for high-volume applications. Pulsecom solutions are designed for emerging lower line count sites. Pick and Choose Every Pulsecom card works independently: Mix any combination of DS1, DS3, 10/100/1000Mb Ethernet. Use 1 card. Use 2 cards. Use 100 cards. Use anywhere. Temperature hardened. Use a rack or no rack. Use your existing cabinet. Use a Westell cabinet. Use a Pulsecom cabinet. Use your NCTE mounting. Use a Pulsecom mounting or locking enclosure. Use local power, remote power, or subscriber 24V. Use a single fiber, CWDM, standard 1310nm or multimode for intra-site. No common cards. And no software. OC3 to 12 DS1s OC3 to DS3 4 Cu pairs to DS3 OC3 to 10/100 BT OC48 to 2 GigEs
Pulsecom SONET Extension Modules Function Model Name Description Application DS1 Extensions DS3 Extensions Ethernet Extensions Gigabit Ethernet Extensions DS3/DS1 Mini Muxes O3-4D1A O3-12D1 O3D3-MO O3-3D3 DS3-EXPRESS-RU DS3-EXPRESS-LU OE G2HC D3-14D1 D3-28D1 4 DS1s carried over OC3 fiber (also available in Type 3192 mechanics) Bookend or integrated operation 12 DS1s carried over OC3 fiber Bookend or integrated operation Single DS3 carried over OC3 fiber Type 200 Mechanics Bookend or integrated operation 3 DS3s carried over OC3 fiber Bookend or integrated operation Drop and continue support Single DS3 carried over 4 copper pairs Ready for O3D3-MO fiber upgrade 10/100Mb Ethernet carried over OC3 fiber Type 200 Mechanics Climate hardened 2 Gigabit Ethernet signals carried over OC48 14 DS1s carried over a DS3 Integral 3/1 cross-connect 28 DS1s carried over a DS3 Integral 3/1 cross-connect Type 600 mechanics Cell site access DS1 delivery to businesses Extensions across a campus Extensions up a riser Cell site access DS1 delivery to businesses Extensions across a campus Extensions up a riser Cell site access DS3 delivery to businesses Extensions across a campus Cell site access DS3 delivery to businesses DS3 extensions across a campus OC3/DS3 rings DS1 delivery (when used in conjunction with D3-14D1 and D3-28D1 modules) DS3 delivery to locations with no fiber DS3 extensions up a riser when facilities are owned by a 3 rd party Ethernet to cell sites Transparent LAN across a campus Transparent LAN between distant buildings Dedicated Internet Access VoIP GigE delivery to businesses OC48/GigE rings GigE trunking DS1 delivery DS1 and DS3 delivery (when used with O3-3D3) DS1 delivery DS1 and DS3 delivery (when used with O3-3D3)
Other Modules Function Model Name Description Applications Span Powering Units SP-CO and SP-RT Span powering units Type 200 Mechanics Powering far-end or mid-span equipment over copper pairs Broadband Audio Test Units PCAU HD PCAU DS1-BOB Transports high-quality audio over twisted pair and TDM Transports HD Radio TM and RDS Transmission over twisted pair and TDM DS1 Break-out board used with O3-4D1A and O3-12D1 to access DS1 ports Studio-to-transmitter links between radio station and transmission tower Studio-to-transmitter links between radio station and transmission tower for High Definition Radio Pre-test of O3-4D1A or O3-12D1 circuits prior to a flash cut from copper to fiber Span Powering Units HD Radio TM Transport
Power Systems Function Model Name Description Application AC/DC Converter 2100-0300 DC/DC Converter 24-48DC Power Node/6A OSP Power Systems Power Node/6AU Converts AC to -48V @1A Includes wall mount bracket Converts +/-24V to -48V Power source and 8 hr. battery back-up (at 0.7A rate) in an OSP cabinet Same as Power Node/6A without batteries installed Powering telco equipment on a customer premise Powering telco equipment at a cell site where 24V is typically available Stand-alone power source with battery backup Stand-alone power source 24-48DC Power Node/6AU
Mountings Model Name Application Description 3O3D3-CPL2C CPE Locking, wall-mount enclosure Integral DS1, DS3 and 10/100/10000Mb bulkhead demarcation jacks Climate hardened 24 or 48VDC operation CPL2C RT, CPE Wall mounting accommodating: 3 Type 200 Mechanics modules 2 Type 400 modules 1 Type 400 + 2 Type 200 Mechanics modules or 1 Type 600 + 1 Type 200 Mechanics modules 2O3D3-19A 2-position rack mounting accommodating: 2 Type 200 Mechanics modules 2 Type 400 modules or 1 Type 400 + 1 Type 200 Mechanics modules Mounts in 19 or 23 racks 3O3D3-23L2A 3-position rack mounting accommodating 3 Type 200 Mechanics modules Mounts in 23 racks 3O3D3-CPL2C with integral bulkhead demarcs O3D3-RT Single-position rack or wall mounting accommodating: 1 Type 200 Mechanics module or 1 Type 400 module 2O3D3-RT 2-position rack or wall mounting accommodating: 2 Type 200 Mechanics module or 1 Type 400 modules 3GME EXPRESS-RH RT 3-position rack or wall mounting accommodating: 1 Type 600 + 1 Type 400 modules or 2 Type 400 + 1 Type 200 modules Outdoor cabinet accommodating: 2 Type 400 modules + 1 Span powering module 2O3D3-19A 3GME-PN RT Outdoor cabinet accommodating: 1 Type 600 + 1 Type 400 modules or 2 Type 400 + 1 Type 200 Mechanics modules 120V powered Battery back-up CSSI RT Snap-in Retrofit Kit for existing Westell CP528DP cabinets
Enable DS1 DS3 Ethernet Gigabit Ethernet Simplify Installation Turn-up Migration Extend Range Facility capacity Each Pulsecom module is: Self-contained Functionally optimized Environmentally hardened Extensive mounting options Industry standard shelves Locking wall enclosures Outdoor pole-mounted cabinets Add or replace a card for new services Extend services: Up a riser Across a campus Across a metro area SFP optics on fiber-based products support single fiber, CWDM and DWDM No high-cost systems No common cards Easy migration to higher-rate services Mounting options enable placement in various locations both indoor and out. No service islands or service restrictions Increase revenue by expanding service offerings to areas that were previously cost-prohibitive to reach. 45 Years Telecom Excellence Established in 1963, Pulsecom became a subsidiary of Hubbell Incorporated (NYSE: HUBA, HUBB) ten years later. Pulsecom designs and manufactures Telecommunications Access Products at its Herndon, Virginia headquarters. Pulsecom s mission is to develop products that simplify last mile access by leveraging existing facilities, minimizing provisioning requirements and accelerating service delivery via a unique, standard mechanics, building block architecture. Pulsecom s innovation grows from its decades of network experience and committed employees. www.pulse.com 2900 Towerview Road, Suite 100 Herndon, VA 20171 Headquarters: 703-471-2900 Customer Service: 800-381-1997 Pulsecom is a registered trademark of Hubbell Incorporated. HD Radio is a trademark of ibiquity Digital Corporation. 200 Mechanics is a registered trademark of Westell Technologies, Inc. Information contained in this publication is subject to change without notice. 2008 Pulse Communications, Inc.