HDMI05-02F3 5-line IPAD, HDMI control line ESD protection Features Low line capacitance: 12 pf max. High efficiency in ESD protection Lead-free package Very thin package High reliability offered by monolithic integration High reduction of parasitic elements through integration and wafer level packaging Complies with the standards: IEC 61000-4-2 Level 4 ± 15 kv (air discharge) ± 8 kv (contact discharge) IEC 61000-4-2 Level 1 ± 2 kv (air discharge) ± 2 kv (contact discharge) Application Where ESD protection for HDMI control lines (,, S and ) is required: Mobile phones and communication systems Portable multimedia players Camcorder, digital still cameras Description The HDMI05-02F3 chip is a low capacitance ESD protection for HDMI control pins. It also integrates pull-up resistor for I²C bus and pulldown resistor for hot plug detect and pull-up resistor for line. The ESD protection circuitry prevents damage to the protected device when subjected to ESD surges up to 15 kv. Figure 1. Figure 2. A2 A3 B3 C3 S A1 Flip Chip 9 bumps Pin configuration (bump side) 3 S 2 GND GND Schematic TM: IPAD is a trademark of STMicroelectronics. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. 1 RPU2 RPU B2 and C2 are ground pins R3 A B C R2 C1 R1 R4 B1 April 2010 Doc ID 15516 Rev 2 1/9 www.st.com 9
Characteristics HDMI05-02F3 1 Characteristics Table 1. Absolute maximum ratings (T amb = 25 C) Symbol Parameter Value Unit V PP External pins (A1, A2, A3, B3 and C3): ESD IEC 61000-4-2, level 4 - air discharge ESD IEC 61000-4-2, level 4 - contact discharge Internal pins (B1, C1): ESD IEC 61000-4-2, level 1 - air discharge ESD IEC 61000-4-2, level 1 - contact discharge Pd Line resistance power dissipation at 70 C 60 mw T op Operating temperature range -30 to + 85 C T stg Storage temperature range -55 to + 150 C 15 8 2 2 kv Figure 3. Electrical characteristics (definitions) Symbol Parameter V BR = Breakdown voltage I RM = Leakage current @ VRM V RM = Stand-off voltage V = Clamping voltage R d = Dynamic impedance I PP = Peak pulse current I R = Breakdown current αt = Voltage temperature coefficient V F = Forward voltage drop C line = Line capacitance R = Series resistance between Input I/O V BR V V RM I F Slope = 1/Rd I I RM I R I PP V F V Table 2. Electrical characteristics (T amb = 25 C) Symbol Test condition Min. Typ. Max. Unit V BR I R = 1 ma 6 20 V I RM V RM = 3 V per line 50 200 na R 1, R 2 1575 1750 1925 Ω R 3 80 100 120 kω R 4 22 27 32 kω C line V line = 0 V, V osc = 30 mv, F = 1 MHz to GND with R PU2 not connected S and to GND with R PU not connected (measured under zero light conditions) 14 24 17 29 pf C line (1) V line = 0 V, V osc = 30 mv, F = 1 MHz, S and to GND with R PU and R PU2 grounded (measured under zero light conditions) 10 12 pf 1. This is the line capacitance seen by the data signals in the application conditions 2/9 Doc ID 15516 Rev 2
HDMI05-02F3 Characteristics Figure 4. S21(dB) versus frequency Figure 5. Analog crosstalk measurements db db 0.00 0.00-5.00 S - 40.00-10.00-80.00-15.00 F(Hz) - 20.00 300.0k 1.0M 3.0M 10.0M 30.0M 100.0M 300.0M 1.0G 3.0G - 120.00 F(Hz) - RPU2 - S S - RPU - S S - - 160.00 300.0k 1.0M 3.0M 10.0M 30.0M 100.0M 300.0M 1.0G 3.0G Figure 6. ESD response to IEC 61000-4-2 on line 7 1 5 2 Figure 7. ESD response to IEC 61000-4-2 on line 39 V 3-17 V 2-1 3-5 1 Figure 8. ESD response to IEC 61000-4-2 on S line Figure 9. ESD response to IEC 61000-4-2 on S line 70 V 1 48 V 2 39 V 3-1 3-5 1-17 V 2 Doc ID 15516 Rev 2 3/9
Characteristics HDMI05-02F3 Figure 10. ESD response to IEC 61000-4-2 on line Figure 11. ESD response to IEC 61000-4-2 on line 79 V 1 5 2 39 V 3-2 2-14 V 3-57 V 1 Figure 12. ESD response to IEC 61000-4-2 on line Figure 13. ESD response to IEC 61000-4-2 on line 65 V 1 49 V 2 40 V 3-43 V 1-17 V 2-1 3 Figure 14. ESD response to IEC 61000-4-2 on 5 V line Figure 15. ESD response to IEC 61000-4-2 on 5 V line 7 1 5 2 3 V @ 60 ns: clamping voltage @ 60 ns 39 V 3-14 V 3-20 V 2-5 1 4/9 Doc ID 15516 Rev 2
HDMI05-02F3 Typical application schematic 2 Typical application schematic Figure 16. Implementation with HDMI Host (Mobile (Mobile Phone) Phone) video Multimedia audio controller Ctrl / status V DD_ HDMI HDMIULC6-4F3 HDMI05-02F3 TX2- TX2+ TX1- TX1+ TX0- TX0+ TC- - TC+ S TX2- TX2+ TX1- TX1+ TX0- TX0+ TC- - TC+ S V DD_ video Display (TV, flat panel, monitor, projector) audio Multimedia controller Ctrl / status Type Type Type C C Connector Connector connector Pin-out Pin -out B2 E2 4 TMDS channel HDMIULC6-4F3 A1 A3 C1 C3 D1 D3 F1 F3 VDD_ A1 A3 C1 C3 D1 D3 F1 F3 27K 2 x 1K75 S HDMIULC6-4F3 B2 E2 100K J4 1 TMDS DATA2 SHIELD 2 TMDS DATA2 + 3 TMDS DATA2-4 TMDS DATA1 SHIELD 5 TMDS DATA1 + 6 TMDS DATA1-7 TMDS DATA0 SHIELD 8 TMDS DATA0 + 9 TMDS DATA0-10 TMDS K SHIELD 11 TMDS K + 12 TMDS K- 13 DDC / EEC GROUND 14 15 S 16 17 RESERVED 18 + POWER 19 HOT PLUG DETECT HDMI05-02F3 Doc ID 15516 Rev 2 5/9
Ordering information scheme HDMI05-02F3 3 Ordering information scheme Figure 17. Ordering information scheme HDMI 05-02 F3 Function HDMI = HDMI Protection Number of lines 05 = 5 lines Application = Control lines Version 02 = with Pull-up integrated Package F3 = Flip Chip 0.4 mm pitch 4 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. Figure 18. Flip Chip dimensions 400 µm ± 40 255 µm ± 40 605 µm ± 55 400 µm ± 40 1.14 mm ± 30 µm 1.14 mm ± 30 µm 6/9 Doc ID 15516 Rev 2
HDMI05-02F3 Package information Figure 19. Footprint Figure 20. Marking Copper pad Diameter: 220 µm recommended 260 µm maximum Solder mask opening: 300 µm minimum Solder stencil opening : 220 µm recommended Dot, ST logo xx = marking z = manufacturing location yww = datecode (y = year ww = week) x y x w E z w Figure 21. Flip Chip tape and reel specification 4.0 ± 0.1 Ø 1.5 ± 0.1 8.0 ± 0.3 1.75 ± 0.1 1.24 STE xxz yww STE xxz yww STE xxz yww 3.5 ±- 0.1 0.69 ± 0.05 1.24 4.0 ± 0.1 All dimensions in mm User direction of unreeling Doc ID 15516 Rev 2 7/9
Ordering information HDMI05-02F3 5 Ordering information Table 3. Ordering information Order code Marking Package Weight Base qty Delivery mode HDMI05-02F3 JG Flip Chip 1.76 mg 5000 Tape and reel (7 ) 6 Revision history Table 4. Document revision history Date Revision Changes 24-Mar-2009 1 First issue. 07-Apr-2010 2 Updated Figure 18. 8/9 Doc ID 15516 Rev 2
HDMI05-02F3 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 15516 Rev 2 9/9