Page 1 sur 11 PEUGEOT 605 XU10J2Z ENGINE BOSCH MOTRONIC MP3.1 INJECTION IGNITION CHECKS REPAIRS ADJUSTMENTS Ref. KA AI 01 CONTENTS GENERAL ENGINE IDENTIFICATION REMINDER OF THE PRINCIPLE OF OPERATION NOMENCLATURE - WIRING DIAGRAMS FAULT FINDING PROCEDURE SEQUENCE TO BE FOLLOWED PRECAUTIONS TO BE TAKEN FAULT FINDING CHARTS GENERAL ENGINE IDENTIFICATION The engine is identified by plates riveted to the cylinder block: (a) Riveted plate bearing the engine type: RFZ (b) Riveted plate bearing the engine number REMINDER OF THE PRINCIPLE OF OPERATION The management of petrol injection is identical to that of the XU10J2Z engine (brochure ref. KA IR 01). The mapped type ignition is managed by the same control unit as the injection. The information transmitted by the various sensors, exploited by the control unit, is used to control ignition and injection. The double coil (two primary and two secondary circuits) with four high tension outlets is controlled by the ignition amplifier module. This is not yet integral with the control unit, and controls each of the two circuits alternately.
Page 2 sur 11 The system is made up of: 1. Control unit 2. Inlet manifold pressure sensor 3. Throttle potentiometer 4. Oxygen sensor 5. Catalytic converter 6. Injection-ignition test warning lamp 7. Injection-ignition test connector 8. Fuel tank 9. Fuel pump 10. Fuel filter 11. Pulsation damper 12. Distribution pipe 13. Pressure regulator 14. Injector 15. Inlet air thermistor 16. Coolant thermistor 17. Engine speed sensor 18. Ignition coil 19. Spark plug 20. Injection relay 21. Fuel pump relay 22. Ignition module 23. Canister 24. Canister purge valve 25. Canister purge cut-off solenoid valve 26. Idle regulation valve For further information on the operation of this system, refer to the "principle of operation" brochure ref. LE AD 02.
Page 3 sur 11
Page 4 sur 11
Page 5 sur 11 NOMENCLATURE - WIRING DIAGRAMS COMPONENTS BB0 Battery BB1 Battery plus unit CA Ignition switch PSF Connection board - Fuse box C1300 Injection-ignition test connector V1300 Injection-ignition text warning lamp 1000 Starter inhibitor switch (automatic transmission)* 1105 Ignition amplifier module 1135 Ignition coil 1200 Fuel pump relay 1210 Fuel pump 1215 Canister purge solenoid valve 1217 Canister purge cut-off solenoid valve 1220 Coolant thermistor 1239 Idle regulation valve 1240 Inlet air thermistor 1302 Injection supply relay 1313 Engine speed sensor 1317 Throttle potentiometer 1319 Injection coding resistor (not fitted) 1320 Injection-ignition control unit 1330 Injectors 1345 Oxygen sensor heater relay 1350 Oxygen sensor 4 Instrument panel 4210 Tachometer 8000 Air conditioning switch* 8005 Compressor supply relay* NOTE
Page 6 sur 11 Sealed foolproof connectors with different colours fitted to the oxygen sensor 1350: red connector in place of black for the heater white connector in place of blue for the signal This modification will not take effect at the same time for the connectors at the harness and sensor ends. * According to equipment SEQUENCE TO BE FOLLOWED FAULT FINDING PROCEDURE When fault finding on this system, it is imperative to follow the sequence shown on page 10 of brochure ref. KA IR 01, taking account of the modifications. PRECAUTIONS TO BE TAKEN Use EUROSUPER unleaded petrol RON 95 minimum FAULT FINDING CHARTS Introduction of the double coil entails changes to some charts to some charts because of modifications to the harnesses and components: Checking the presence of high tension at cylinders 1-4 and 2-3: see page 7 Check of ignition coil 1 1135: see page 8 Check of ignition coil 2 1135: see page 8 Check of the ignition amplifier module 1105: see page 11 There is no change to the fault codes and the other fault finding charts: see the list in brochure ref. KA IR 01 page 26 NOTE When brochure ref. KA IR 01 calls for an ignition check, refer to pages 7, 8 and 11 of this supplement
Page 7 sur 11 IGNITION SYSTEM SPARK PLUGS Type: EYQUEM RFC 52LS or CHAMPION RC 9YCC Electrode gap: 0,8+ 0,05 mm Tightening torque : 2,75 m.dan ( 20 Ibf ft) CHECKS Prior conditions Supply to control unit 1320 correct: see pages 28 and 31 KA IR 01 Check of injection relay 1302 correct: see page 31 KA IR 01 Engine speed sensor 1313 correct: see page 45 KA IR 01
Page 8 sur 11
Page 9 sur 11
PEUGEOT 605 - XU10J2Z ENGINE BOSCH MOTRONIC MP3.1 INJECTION I... Page 10 sur 11
PEUGEOT 605 - XU10J2Z ENGINE BOSCH MOTRONIC MP3.1 INJECTION I... Page 11 sur 11 12.02.2000