8 MM SQUARE DRIVE ROLLER DOOR LOCK This lock is ideal for use on truck shutters and applications that require a T handle to provide 2-point locking. The lock can be secured with a pair of dome nuts (optional), which are fitted from the front of the panel, enabling the screws to secure the lock from the rear. The hole centre fixing allows the A/HT8F mini T handle or A/HG-R large T handle to be fitted to drive the arms. A/V3RP 8 mm square drive ion A / V 3 R P / - - / 1 - / L - 4 Ordering example: A / V 3 R P / - - / 1 - / L - 4 D1
V1 ROLLER DOOR LOCK This lock is ideal for use on roll-up doors. It is used mainly as a replacement for damaged locks fitted to older doors. The fascia is a traditional design, wrapping around the rib on the door. Zinc alloy diecast fascia - chrome finish Zinc alloy die cast lock - clear zinc-plated Key series 19-100 combinations Non-master keying Operation of this lock is described below Unlocked (arms retracted) A/V1PB Latch operation Position Locked (arms extended) This lock can be operated from the front using a key, or from the rear using the latch. The latch can be operated at all times, independently of any key operation. Key removable in horizontal position only. A / V 1 P B / 1 9 / 3 H / L - 6 Ordering example: A / V 1P B / 1 9 /3 H / L - 6 D2
V4 ROLLER DOOR LOCK This lock is ideal for use on roll-up doors. The fascia features two pockets which provide grip to lift or lower the door. Zinc alloy diecast fascia - black finish Operation of this lock is described below Unlocked (arms retracted) Latch operation position Locked (arms extended) Code Information This lock can be operated from the front, using a key, or from the rear using the latch. The latch can be operated at all times, independently of any key operation. Key removable in horizontal position only. A/V4P- Fascia KEY SERIES 19 100 combinations - non-master keying A / V 4 P - / KEY SERIES / 6 H / L - 6 Ordering example: A / V 4 P- / 1 9 / 6 H / L - 6 D3
V5 ROLLER DOOR LOCK This lock is ideal for use on roll-up doors. The fascia features one pocket which provides grip to lift or lower the door. A/VP-- Zinc alloy diecast fascia - black finish Operation of this lock is described below Unlocked (arms retracted) Latch operation position Locked (arms extended) This lock can be operated from the front, using a key, or from the rear using the latch. The latch can be operated at all times, independently of any key operation. Key removable in horizontal position only. Fascia Shown at 40% Code Information KEY SERIES 19 100 combinations - non-master keying A / V P - - / KEY SERIES / 6 H / L - 8 Ordering example: A / V P - - / 1 9 / 6 H / L - 8 D4
V9 ROLLER DOOR LOCK Front view of lock This lock is ideal for use on roll-up doors. Key series 23-400 combinations Double-entry - non-master keying Plastic latch allowing internal lock operation Operation of this lock is described below A/V9P- Latch operation position Unlocked (arms retracted) Locked (arms extended) This lock can be operated from the front using a key or from the rear using the latch. The latch can be operated at all times, independently of any key operation. Key removable in horizontal position only. Latch operation from rear Side view on lock A / V 9 - - / 2 3 / 6 H / L - A Ordering example: A / V 9 - - / 2 3 / 6 H / L - A D5
V9 C4 ROLLER DOOR LOCK This lock is ideal for use on roll-up doors but can also be mounted vertically for sliding door applications. It is mainly used as a replacement for damaged locks fitted to older doors, and for shutters that require either a restricted or master key system. A/V9C4 Front view of lock The fascia has a 14 mm projection and is secured from the rear of the panel by two screws. Zinc alloy diecast fascia - satin chrome finish 5-pin brass cylinder (supplied separately) For conversion of existing locks, contact Lock Focus for details Code Information KEYING DETAIL KA Keyed alike KD Keyed to differ NB No barrel (pre-loaded cylinder) ## No cylinder Fascia To unlock To lock A / V 9 C 4 / KEYING DETAIL / 4 - / - L L Ordering example: A / V 9 C 4 / K D / 4 - / - L L D6
V9 ROLLER DOOR LOCK LOW PROFILE VERSION This lock is ideal for use on roll-up grilles/doors where the minimum external fascia projection is required. It is mainly used for shutters that require either a restricted or master key system. The fascia has a 7.8 mm projection and is secured from the rear of the panel by two screws. Zinc alloy diecast fascia - satin chrome finish 5-pin brass cylinder (supplied separately) Low profile fascia Suitable for mounting on 1.4 mm thick extrusions A/V9LP To unlock To lock Code Information KEYING DETAIL KA Keyed alike KD Keyed to differ NB No barrel (pre-loaded cylinder) ## No cylinder A / V 9 L P / KEYING DETAIL / 4 - / - L L Ordering example: A / V 9 L P / K D / 4 - / - L L D7
ROLLER SHUTTER LOCK This lock is ideal for use on roller shutters. It is supplied with a pair of dome nuts (optional), which are fitted from the front of the panel, enabling screws to secure the lock from the rear. Zinc alloy diecast fascia - chrome-plated nozzle and clear zinc housing Key series 19-100 combinations Non-master keying Optional dome nuts and screws Operation of this lock is described below Unlocked (arms retracted) A/V2-- Latch Operation from Rear Latch operation position Locked (arms extended) This lock can be operated from the front using a key, or from the rear using the latch. The latch can be operated at all times, independently of any key operation. Dome Nuts and Screws Key removable in horizontal position only. A / V 2 - - / 1 9 / 3 H / L - 6 Ordering example: A / V 2 - - / 1 9 / 3 H / L - 6 D8
T SHAPE HANDLE FRONT AND REAR FIXING This lock is ideal for use on garage doors. An 8 mm square drive is operated by unlocking, then rotating the handle. There are two versions: a rear fix and a front fix. The rear fix has 3/16 W tapped holes concealed underneath the rose. The front fix is designed to be used with 3/16 coach bolts fitted from the front of the rose. A/HG-F Front fix Zinc alloy diecast handle and rose Chrome-plated finish One pair of keys per lock A/HG-R Rear fix Code Information KEY SERIES -- Non-locking handle 01 200 combinations - non-master keying 02 200 combinations - master keying 11 2000 combinations - non-master keying 12 2000 combinations - master keying CL Special combinations ES Special combinations FS Special combinations 30,0 24,0 100,0 FINISH 3 Bright chrome MOVEMENT B Handle lockable at both positions 180º A and S Handle lockable at both positions 90º C 90º clockwise rotation of handle to unlock Key removable in both positions SPINDLE - Refer to page D11 CAM TYPE - - Refer to page D10 54,0 44,5 8,0 Square drive spindle Note: Spindles and movements can be changed by customer - refer to page D11 ø12,0 Min. 2 Holes ø5,5 Fixing Details A / HG-R/ KEY SERIES / FINISH + MOVEMENT / SPINDLE + CAM TYPE (Rear fix) A / HG-F/ KEY SERIES / FINISH + MOVEMENT / SPINDLE + CAM TYPE (Front fix) Ordering example: A / H G - R/ 0 1/ 3 B / E - - ADVISE Keying requirements, e.g. keyed alike D9
HANDLE SPINDLES AND CAMS FOR T SHAPE HANDLES Spindle Type E Spindle type E is a standard 8 mm square drive which is 75 mm long from the base of the lock. Spindle Type E and Cam Type 99 The cam type 99 is secured to spindle type E by an M8 grub screw. The distance from the base of the rose to the cam can be adjusted by loosening the grub screw and sliding the cam along the spindle. 16,0 8,0 Sq. 74,05 68,0 10,0 8,0 74,05 Spindle Type T and Cam Type 89 The cam type 89 is fixed to spindle type T by being sandwiched between two M10 nuts. 30º 7,0 Caulk The distance from the base of the rose to the cam can be adjusted by loosening the nuts and sliding the cam along the spindle. 25,0 36,0 51,5 50,05 8,0 Sq. drive Spindle Type Q and 3-Point Locking Cams Spindle type Q is designed to be used with a range of 3-point locking cams (refer to table). SPINDLE TYPE CAM TYPE DIM L DIM B (FLAT) DIM C (STEPPED) END DETAIL The 3-point locking cam has two versions: a flat cam and a stepped cam. The flat cams are spaced at 10 mm from the base of the lock. The stepped cams are spaced at 13.2 mm to 26 mm from the base of the lock, depending on the type. The 3-point locking cam is designed to be used with locking rods. To fit the locking rods, the saddle must be removed. To do this, remove the split pin and take off the saddle. Fit the locking bars, then refit the saddle. Feed the split pin through the hole in the spindle, then spread the pin legs. B 2,0 Q 71 37 10,0 FLAT Q 72 65 10,0 FLAT Q 73 63.5 13,2 CAULKED Q 74 57.5 19,5 CAULKED Q 75 54.5 22,7 CAULKED Q 76 51 26,0 CAULKED 16,0 C L 18,0 35,0 45,0 2,0 3,0 16,0 18,8 Flat Cam 18,8 Stepped Cam Caulk Detail (Stepped Cam Only) D10
LARGE T HANDLE A/HG ASSEMBLY INSTRUCTIONS PLAIN SPINDLES THREADED SPINDLES PLAIN NO THREADED LENGTH L T/SPIN/B2 T/SPIN/L2 31.5 T/SPIN/M2 39.5 T/SPIN/C2 43.5 T/SPIN/D2 T/SPIN/T2 50.5 T/SPIN/E2 74.5 T/SPIN/H2 100.5 T/SPIN/F2 136.5 T/SPIN/N2 62.5 ASSEMBLY PROCEDURE 1. Assemble handle to rose and rotate clockwise over 1/4 turn. 2. Assemble detent bush locating over lug on handle shaft. 3. Assemble spindle to retainer plate by inserting into centre hole and moving spindle sideways to locate in groove. 4. Assemble retainer plate/spindle to handle/rose by inserting spindle into square hole in detent bush and locating retainer plate in rose, with location hole aligned with boss. 5. Insert screw into one of the 3 holes to suit movement required and tighten maximum torque 1.0 Nm. 6. Check function and assemble barrel to handle as required. D11