LT30/LT30-3.3/LT30-5 Micropower DC/DC Converters with Low-Battery Detector Active in Shutdown FEATRES at 200mA from Two Cells 0µA Quiescent Current in Shutdown Operates with as Low as. Low-Battery Detector Active in Shutdown Low Switch V CESAT : 370mV at A Typical 20µA Quiescent Current in Active Mode Switching Frequency p to 300kHz Programmable Peak Current with One Resistor 8-Lead SO Package APPLICATIONS 2-, 3-, or -Cell to or 3.3V Step-p Portable Instruments Bar Code Scanners Palmtop Computers Diagnostic Medical Instrumentation Personal Data Communicators/Computers DESCRIPTION The LT 30 is a micropower step-up DC/DC converter ideal for use in small, low voltage, battery-operated systems. The devices operate from a wide input supply range of. to 8V. The LT30-3.3 and LT30-5 generate regulated outputs of 3.3V and and the adjustable LT30 can deliver output voltages up to 2. Quiescent current, 20µA in active mode, decreases to just 0µA in shutdown with the low-battery detector still active. Peak switch current, internally set at A, can be reduced by adding a single resistor from the pin to ground. The high speed operation of the LT30 allows the use of small, surface-mountable inductors and capacitors. The LT30 is available in an 8-lead SO package., LTC and LT are registered trademarks of Linear Technology Corporation. TYPICAL APPLICATION 2-Cell to Step-p Converter with Low-Battery Detect 2 CELLS * SMIDA CD5-220 ** N587 LBI 3 99k 60k LT30-5 6 LBO 7 5 22µH* 8 2 D** 200mA 00k LBO LOW WHEN V BAT < 2.2V 30 TA0 EFFICIEY (%) 90 80 70 60 50 Efficiency 0 0. 0 00 500 LOAD CRRENT (ma) = 3.3V = 2. =.8V 30 TA02
LT30/LT30-3.3/LT30-5 ABSOLTE MAXIMM RATINGS W W W Voltage... 8V Voltage... 0.V to 2 FB Voltage (LT30)... 0.3V Sense Voltage (LT30-3.3/LT30-5)... 8V Voltage... Voltage... 6V LBI Voltage... LBO Voltage... 8V Maximum Power Dissipation... 500mW Junction Temperature... 25 C Operating Temperature Range... 0 C to 70 C Storage Temperature Range... 65 C to 50 C Lead Temperature (Soldering, 0 sec)... 300 C PACKAGE/ORDER INFORMATION LBI LBO 2 3 TOP VIEW S8 PACKAGE 8-LEAD PLASTIC SO *FIXED OTPT VERSION T JMAX = 25 C, θ JA = 50 C/W 8 FB ()* 7 6 5 Consult factory for Industrial and Military grade parts. W ORDER PART NMBER LT30CS8 LT30CS8-3.3 LT30CS8-5 S8 PART MARKING 30 303 305 ELECTRICAL CHARA CTERISTICS = 2V, V = 2V unless otherwise noted. PARAMETER CONDITIONS MIN TYP MAX NITS Minimum Operating Voltage.5.65 V Operating Voltage Range 8 V Quiescent Current V = 2V, Not Switching 20 200 µa Quiescent Current in Shutdown V = 0V, = 2V 7 5 µa V = 0V, = 27 50 µa Comparator Trip Point LT30.22.2.26 V FB Pin Bias Current LT30 0 25 na Sense Pin Leakage in Shutdown V = 0V, Fixed Output Versions 0.002 µa Output Sense Voltage LT30-3.3 3.7 3.3 3.3 V LT30-5.80 5.05 5.25 V Line Regulation.8V 8V 0.0 0.5 %/V LBI Input Threshold Falling Edge.0.7.25 V LBI Bias Current 6 20 na LBI Input Hysteresis 35 65 mv LBO Output Voltage Low I SINK = 500µA 0.2 0. V LBO Output Leakage Current LBI =., LBO = 0.0 0. µa Input Voltage High. V Input Voltage Low 0. V Pin Bias Current V = 5 8 µa V = 0V 5 2 µa Switch OFF Time.5 2 µs Switch ON Time Current Limit Not Asserted 6 8 µs Maximum Duty Cycle Current Limit Not Asserted 76 80 88 % Peak Switch Current Pin Open, = 0.8.2 A 20k from to 500 ma 2
ELECTRICAL CHARA CTERISTICS The denotes specifications which apply over the 0 C to 70 C operating temperature range. LT30/LT30-3.3/LT30-5 = 2V, V = 2V unless otherwise noted. PARAMETER CONDITIONS MIN TYP MAX NITS Switch Saturation Voltage I = A 0.37 V I = 700mA 0.26 0.35 V Switch Leakage Switch Off, V = 0.0 7 µa TYPICAL PERFORMAE CHARACTERISTICS W SATRATION VOLTAGE (mv) Switch Saturation Voltage 500 T A = 25 C 00 300 200 00 PEAK CRRENT (A).3.2..0 0.9 0.8 0.7 Peak Switch Current Limit TIME (µs) On- and Off-Times 8 7 MAXIMM ON-TIME 6 5 3 2 OFF-TIME 0 0 0.2 0. 0.6 0.8 ITCH CRRENT (A).0.2 0.6 50 25 0 25 50 75 00 TEMPERATRE ( C) 0 50 25 0 25 50 75 00 TEMPERATRE ( C) 30 G0 30 G02 30 G03 FEEDBACK VOLTAGE (V).250.25.20.235.230.225.220.25.20.205 Feedback Voltage BIAS CRRENT (na) 20 8 6 2 0 8 6 2 Feedback Pin Bias Current SPPLY CRRENT (µa) 300 250 200 50 00 50 Supply Current T A = 25 C V = NOT ITCHING V = 0V.200 50 25 0 25 50 TEMPERATRE ( C) 75 00 0 50 25 0 25 50 TEMPERATRE ( C) 75 00 0 0 2 3 5 6 7 8 INPT VOLTAGE (V) 30 G0 30 G05 30 G06 3
LT30/LT30-3.3/LT30-5 TYPICAL PERFORMAE CHARACTERISTICS W V OT 00mV/DIV AC COPLED Load Transient Response V OT 00mV/DIV AC COPLED V /DIV Burst Mode TM Operation I LOAD 200mA 0 I L 500mA/DIV 00µs/DIV 30 G07 = 2. 20µs/DIV 30 G08 V OT = I LOAD = 85mA L = 22µH Burst Mode is a trademark of Linear Technology Corporation. PIN FTIONS LBI (Pin ): Low-Battery Detector Input. When voltage on this pin is less than.7v, detector output is low. LBO (Pin 2): Low-Battery Detector Output. Open collector can sink up to 500µA. Low-battery detector remains active when device is shut down. (Pin 3): Input Supply. Must be bypassed close (<0.2") to the pin. See required layout in the Typical Applications. (Pin ): Collector of Power NPN. Keep copper traces on this pin short and direct to minimize RFI. (Pin 5): Device Ground. Must be low impedance; solder directly to ground plane. (Pin 6): Current Limit Set Pin. Float for A peak switch current; a resistor to ground will lower peak current. (Pin 7): Shutdown Input. When low, switching regulator is turned off. The low-battery detector remains active. The input should not be left floating. If is not used, tie the pin to. FB/ (Pin 8): On the LT30 (adjustable) this pin goes to the comparator input. On the fixed-output versions, the pin connects to the resistor divider which sets output voltage. The divider is disconnected from the pin during shutdown.
LT30/LT30-3.3/LT30-5 BLOCK DAGRA I W S C L D C2 V OT 2 LB0 3 LBI. NDERVOLTAGE LOCKOT 36mV A3 A2 R2 k R 7.2Ω R3 R 8 FB.7V A ENABLE OFF TIMERS 6µs ON.5µs OFF BIAS ~V DRIVER Q3 k Q2 Q 200.2V V REF 7 6 5 30 F0 Figure. LT30 Block Diagram. Independent Low-Battery Detector A3 Remains Alive When Device Is in Shutdown LBI LB0 2 3 8. NDERVOLTAGE LOCKOT 36mV A3 A2 R2 k R 7.2Ω 590k.7V OFF BIAS ~V Q3 R A ENABLE TIMERS 6µs ON.5µs OFF DRIVER k Q2 Q 200.2V V REF R = 355k (LT30-3.3), 95k (LT30-5) 7 6 5 30 F02 Figure 2. LT30-3.3/LT30-5 Block Diagram 5
LT30/LT30-3.3/LT30-5 OPERATIO The LT30 s operation can best be understood by examining the block diagram in Figure. Comparator A monitors the output voltage via resistor divider string R3/R at the FB pin. When V FB is higher than the.2v reference, A2 and the timers are turned off. Only the reference, A and A3 consume current, typically 20µA. As V FB drops below.2v plus A s hysteresis (about 6mV), A enables the rest of the circuit. Power switch Q is then cycled on for 6µs, or until current comparator A2 turns off the ON timer, whichever comes first. Off-time is fixed at approximately.5µs. Q s switching causes current to alternately build up in inductor L and discharge into output capacitor C2 via D, increasing the output voltage. As V FB increases enough to overcome C s hysteresis, switching action ceases. C2 is left to supply current to the load until V OT decreases enough to force A s output high, and the entire cycle repeats. If switch current reaches A, causing A2 to trip, switch ON time is reduced. This allows continuous mode operation during bursts. A2 monitors the voltage across 7.2Ω resistor R, which is directly related to the switch current. Q2 s collector current is set by the emitter-area ratio to 0.5% of Q s collector current. R s voltage drop exceeds 36mV, corresponding to A switch current, A2 s output goes high, truncating the ON time part of the switch cycle. The A peak current can be reduced by tying a resistor between the pin and ground, causing a voltage drop to appear across R2. The drop offsets some of the 36mV reference voltage, lowering peak current. A 22k resistor limits current to approximately 550mA. A capacitor connected between and ground provides soft start. Shutdown is accomplished by grounding the pin. The low-battery detector A3 has its own.7v reference and is always on. The open collector output device can sink up to 500µA. Approximately 35mV of hysteresis is built into A3 to reduce buzzing as the battery voltage reaches the trip level. Inductor Selection Inductors used with the LT30 must be capable of handling the worst-case peak switch current of.2a without saturating. Open flux rod or drum core units may be biased into saturation by 20% with only a small reduction in efficiency. For the majority of 2-cell or 3-cell input LT30 applications, a 22µH or 20µH inductor such as the Sumida CD5-220 (drum) or Coiltronics CTX20- (toroid) will suffice. If switch current is reduced using the pin, smaller inductors such as the Sumida CD3 series or Coilcraft DO608 series can be used. Minimizing DCR is important for best efficiency. Ideally, the inductor DCR should be less than 0.05Ω, although the physical size of such an inductor makes its use prohibitive in many space conscious applications. If EMI is a concern, such as when sensitive analog circuitry is present, a toroidal inductor such as the Coiltronics CTX20- is suggested. A special case exists where the V OT / differential is high, such as a 2V to 2V boost converter. If the required duty cycle for continuous mode operation is higher than the LT30 can provide, the converter must be designed for discontinuous operation. This means that the inductor current decreases to zero during the switch OFF time. For a simple step-up (boost) converter, duty cycle can be calculated by the following formula: DC = [( V SAT )/(V OT V D )] where, = Minimum input voltage V SAT = Switch saturation voltage (0.3V) V OT = Output voltage V D = Diode forward voltage (0.V) If the calculated duty cycle exceeds the minimum LT30 duty cycle of 76%, the converter should be designed for discontinuous mode operation. The inductance must be low enough so that current in the inductor reaches the peak current in a single cycle. Inductor value can be calculated by: L = ( V SAT )(t ON /A) where, t ON = Minimum on-time of LT30 (µs) One advantage of discontinuous mode operation is that inductor values are usually quite low so very small units can be used. Ripple current is higher than with continuous mode designs and efficiency will be somewhat less. 6
LT30/LT30-3.3/LT30-5 OPERATIO Table lists inductor suppliers along with appropriate part numbers. Table. Recommended Inductors VENDOR SERIES PHONE NMBER Sumida CD5, CD3 (708) 956-0666 Coiltronics CTX20- (07) 2-7876 Dale LPT55 (605) 665-930 Coilcraft DO336, DO608, DO3308 (708) 639-600 Capacitor Selection Low ESR (Equivalent Series Resistance) capacitors should be used at the output of the LT30 to minimize output ripple voltage. High quality input bypassing is also required. For surface mount applications AVX TPS series tantalum capacitors are recommended. These have been specifically designed for switch mode power supplies and have low ESR along with high surge current ratings. A, 0V AVX TPS surface mount capacitor typically limits output ripple voltage to 70mV when stepping up from 2V to at a 200mA load. For through hole applications Sanyo OS-CON capacitors offer extremely low ESR in a small package size. Again, if peak switch current is reduced using the pin, capacitor requirements can be eased and smaller, higher ESR units can be used. Suggested capacitor sources are listed in Table 2. Function The LT30 s current limit ( ) pin can be used for soft start. pon start-up, the LT30 will draw maximum current (about A) from the supply to charge the output capacitor. Figure 3 shows V OT and waveforms as the device is turned on. The high current flow can create IR drops along supply and ground lines or cause the input supply to drop out momentarily. By adding R and C as shown in Figure, the switch current is initially limited to well under A as detailed in Figure 5. Current flowing into C from R and the pin will eventually charge C and R effectively takes C out of the circuit. R also provides a discharge path for C when is brought low for turn-off. V OT 2V/DIV I IN 500mA/DIV V 0V/DIV ms/div 30 F03 Figure 3. Start-p Response. Input Current Rises Quickly to A. V OT Reaches in Approximately ms. Output Drives 20mA Load Table 2. Recommended Capacitors 22µH* MBRS30L VENDOR SERIES TYPE PHONE NMBER AVX TPS Surface Mount (803) 8-9 Sanyo OS-CON Through Hole (69) 66-6835 Sprague 595D Surface Mount (603) 225-96 LBI LT30-5 200mA Diode Selection Best performance is obtained with a Schottky rectifier such as the N588. Motorola makes the MBRS30L Schottky which is slightly better than the N588 and comes in a surface mount package. For lower switch currents, the MBR0530 is recommended. It comes in a very small SOD-23 package. Multiple N8s in parallel can be used in a pinch, although efficiency will suffer. 2 CELLS *SMIDA CD5-220 LB0 C µf Figure. 2-Cell to /200mA Boost Converter Takes Four External Parts. Components with Dashed Lines Are for Soft Start (Optional) R M 30 F0 7
LT30/LT30-3.3/LT30-5 OPERATIO If the full power capability of the LT30 is not required, peak switch current can be limited by connecting a resistor R LIM from the pin to ground. With R LIM = 22k, peak switch current is reduced to approximately 500mA. Smaller power components can then be used. The graph in Figure 6 shows switch current vs R LIM resistor value. V OT 2V/DIV I IN 500mA/DIV bypass capacitor is required. If the input supply is close to the IC, a µf ceramic capacitor can be used instead. The LT30 switches current in A pulses, so a low impedance supply must be available. If the power source (for example, a 2 AA cell battery) is within or 2 inches of the IC, the battery itself provides bulk capacitance and the µf ceramic capacitor acts to smooth voltage spikes at switch turn-on and turn-off. If the power source is far away from the IC, inductance in the power source leads results in high impedance at high frequency. A local high capacitance bypass is then required to restore low impedance at the IC. V 0V/DIV ms/div 30 F05 Figure 5. Start-p Response with µf/mω Components in Figure 2 Added. Input Current Is More Controlled. V OT Reaches in 6ms. Output Drives 20mA Load 8 2 LT30 7 000 3 6 900 5 PEAK CRRENT (ma) 800 700 600 V OT C OT C IN 500 00 0 00 000 R LIM (kω) 30 F06 Figure 6. Peak Switch Current vs R LIM Value (BATTERY AND LOAD RETRN) 30 F07 Figure 7. Suggested Layout for Best Performance. Input Capacitor Placement as Shown Is Highly Recommended. Switch Trace (Pin ) Copper Area Is Minimized Layout/Input Bypassing The LT30 s high speed switching mandates careful attention to PC board layout. Suggested component placement is shown in Figure 7. The input supply must have low impedance at AC and the input capacitor should be placed as indicated in the figure. The value of this capacitor depends on how close the input supply is to the IC. In situations where the input supply is more than a few inches away from the IC, a 7µF to solid tantalum Low-Battery Detector The LT30 contains an independent low-battery detector that remains active when the device is shut down. This detector, actually a hysteretic comparator, has an open collector output that can sink up to 500µA. The comparator also operates below the switcher s undervoltage lockout threshold, operating until reaches approximately.v. Figure 8 illustrates the input/output characteristic of the detector. Hysteresis is clearly evident in the figure. 8
OPERATIO LT30/LT30-3.3/LT30-5 000 V LBO 2V/DIV HORS (H) 00 0 V LBI 200mV/DIV 30 F08 Figure 8. Low-Battery Detector Transfer Function. Pull-p R = 22k, = 2V, Sweep Frequency = 0Hz 0 00 200 LOAD CRRENT (ma) 30 F0 Battery Life How may hours does it work? This is the bottom line question that must be asked of any efficiency study. AA alkaline cells are not perfect power sources. For efficient power transfer, energy must be taken from AA cells at a rate that does not induce excessive loss. AA cells internal impedance, about 0.2Ω fresh and 0.5Ω end-of-life, results in significant efficiency loss at high discharge rates. Figure 0 illustrates battery life vs load current of Figure 9 s LT30, 2-cell to DC/DC converter. Note the accelerated decrease in hours at higher power levels. Figure plots total watt hours vs load current. Watt hours are determined by the following formula: WH = I LOAD ()(H) L 22µH D Figure 0. Battery Life vs Load Current. Dots Specify Actual Measurements WATT HORS (WH) 6 5 3 2 0 0 00 LOAD CRRENT (ma) 30 F 200 Figure. Output Watt Hours vs Load Current. Note Rapid Fall-Off at Higher Discharge Rates B 2 CELLS C LB B = 2 EVEREADY INDSTRIAL ALKALINE AA CELLS #EN9 C, C2 = AVX TPSD07M00R000 D = MOTOROLA MBRS30L L = SMIDA CD5-220 LT30-5 LB0 V OT 200mA C2 30 F09 Figure s graph varies significantly from electrical efficiency plot pictured on the first page of this data sheet. Why? As more current is drawn from the battery, voltage drop across the cells internal impedance increases. This causes internal power loss (heating), reducing cell terminal voltage. Since the regulator input acts as a negative resistance, more current is drawn from the battery as the terminal voltage decreases. This positive feedback action compounds the problem. Figure 9. 2-Cell to Converter sed in Battery Life Study 9
OPERATIO LT30/LT30-3.3/LT30-5 Figure 2 shows overall energy conversion efficiency, assuming availability of 6.5WH of battery energy. This efficiency approximates the electrical efficiency at load current levels from ma to 0mA, but drops severely at load currents above 0mA (load power above 50mW). The moral of the story is this: if your system needs at more than 0mA to 50mA, consider using a NiCd battery (/0 the internal impedance) instead of a AA cell alkaline battery. ELECTROCHEMICAL EFFICIEY (%) 00 90 80 70 60 50 0 30 20 0 0 0 00 LOAD CRRENT (ma) 200 30 F2 Figure 2. Overall System Efficiency Including Battery Efficiency vs Load Current. Internal Impedance of Alkaline AA Cells Accounts for Rapid Drop in Efficiency at Higher Load Current TYPICAL APPLICATIONS Super Burst TM Low I Q DC/DC Converter I Q 0µA 33µH** MBR0530 90 Super Burst Efficiency 2N3906 200k 0.0µF 80 = 3V 2 CELLS 7k LBO FB LT30 LBI 3.83M*.2M* 00mA 220µF EFFICIEY (%) 70 60 50 = 2V 7k 22k *% METAL FILM ** SMIDA CD5-330 30 TA03 0 0.0 0..0 0 LOAD CRRENT (ma) 00 30 TA0 0 Super Burst is a trademark of Linear Technology Corporation.
LT30/LT30-3.3/LT30-5 TYPICAL APPLICATIONS 2-Cell to 3.3V Boost Converter L* 22µH MBRS30L 90 2-Cell to 3.3V Converter Efficiency 2 CELLS C** *SMIDA CD5-220 **AVX TPSD07M00R000 LT30-3.3 3.3V 300mA C2** 0V 30 TA05 EFFICIEY (%) 80 70 60 50 0 = 3.3V = 2. = 2..8V 30 0. 0 00 000 LOAD CRRENT (ma) 30 TA06 3.3V SEPIC (Step-p/Step-Down Converter) 3.3V SEPIC Efficiency 2. TO 8V LA* 2 C** µf 80 75 C2 7µF 6V LT30-3.3 * COILTRONICS CTX20- ** TOKIN E05ZY5-C03-F AVX TPSD76M06R050 AVX TPSD07M00R000 3 LB* MBRS30L C3 0V 30 TA07 3.3V 300mA EFFICIEY (%) 70 65 60 55 50 =. = 3. = 2. 0 00 500 LOAD CRRENT (ma) 30 TA08 SEPIC (Step-p/Step-Down Converter) SEPIC Efficiency 3V TO 8V LA* 2 C** µf 80 75 7µF 6V LT30-5 3 LB* MBRS30L 200mA 0V EFFICIEY (%) 70 65 60 55 = 6V = = V = 3V * COILTRONICS CTX20- ** TOKIN E05ZY5-C03-F AVX TPSD76M06R050 AVX TPSD07M00R000 30 TA09 50 0 00 500 LOAD CRRENT (ma) 30 TA0
LT30/LT30-3.3/LT30-5 TYPICAL APPLICATIONS to 2V DC/DC Converter to 2V Converter Efficiency L* 22µH D 90 7µF** LT30 FB.07M % 2k % 2V 200mA 7µF** 6V EFFICIEY (%) 85 80 75 70 * SMIDA CD5-220 30 TA ** AVX TPSD76M06R050 MOTOROLA MBRS30L 65 0 00 300 LOAD CRRENT (ma) 30 TA2 Single Li-Ion Cell to Converter with Load Disconnect at < 2.7V (2.7V to.2v) 6V 562k % 220k 22µH** MBRS30LT3 () V OT V OT µf SINGLE Li-Ion CELL* 32k % LT30CS8-5 LBI LBO 0V S EN LTC77 2 3 30 TA3 * PRIMARY Li-Ion BATTERY PROTECTION MST BE PROVIDED BY AN INDEPENDENT CIRCIT ** SMIDA CD5-220 AVX TPSD07M00R000 2
LT30/LT30-3.3/LT30-5 TYPICAL APPLICATIONS Negative LCD Bias Generator L* 0µH 2 CELLS 7µF FB LT30 22k 90.9k % M % 3.3µF.69M % 0k % ** 000pF µf CERAMIC ** ** V OT V TO 22V ma TO 0mA 0µF 3 EFFICIEY = 70% TO 75% AT I LOAD 2mA * SMIDA CD3-00 ** MOTOROLA MBR0530 VOLTAGE ADJST khz PWM INPT 0V TO 30 TA Electroluminescent Panel Driver with 200Hz Oscillator = OPERATE 0V = 2N3906 3.3k 22k 75k 2V TO 7V 22k nf 0.0µF 200Hz LBO LBI 7µF :2* 3 6 MBR0530 FB MR60 600V LT30 5k 22k * DALE LPE3325-A205 TRANSFORMER MEASRES 6.5mm 8.2mm 5.2mm (H) (605) 665-930 DANGER! HIGH VOLTAGE 50k INTENSITY ADJST 0M (3.3M 3) /2 BAW56 µf 200V FMMT58 22k /2 BAW56 22k EL PANEL C PANEL 20nF 30 TA5 3
LT30/LT30-3.3/LT30-5 TYPICAL APPLICATIONS 2- to -Cell to kv Step-p Converter 0.0µF 0.0µF 0.0µF 0.0µF 0.0µF 2V TO 6V 0.µF 7µF LT30 T* 3 0.0µF 0.0µF 0.0µF 0.0µF 6 FB MBR0530 R** 500M R2 620k DANGER! HIGH VOLTAGE V OT kv 250µA ( ) V OT =.2V R R2 * DALE LPE3325-A205 TRANSFORMER MEASRES 6.5mm 8.2mm 5.2mm (H) (605) 665-930 ** IRC CGX-/2 ALL 0.0µF CAPACITORS 250WVDC BAS2 OR MR30 30 TA6 2- to -Cell to Converter with Output Disconnect 2k 2V TO 6V L** 22µH MBRS30L ZTX788B 7µF* LT30-5 22µF* 00mA 220µF* *AVX TPS SERIES TANTALM OR SANYO OS-CON **SMIDA CD5-220 30 TA7
LT30/LT30-3.3/LT30-5 TYPICAL APPLICATIONS 2-Cell to Converter with Auxiliary 0V Output µf CERAMIC MBR0530 MBR0530 0µF 0V 20mA L* 22µH MBRS30L 2 CELLS LT30-5 50mA *SMIDA CD5-220 30 TA8 2-Cell to Converter with Auxiliary Output L* 22µH MBRS30L 2 CELLS LT30-5 µf CERAMIC MBR0530 50mA 20mA MBR0530 0µF *SMIDA CD5-220 30 TA9 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of circuits as described herein will not infringe on existing patent rights. 5
LT30/LT30-3.3/LT30-5 PACKAGE DESCRIPTION Dimension in inches (millimeter) unless otherwise noted. S8 Package 8-Lead Plastic Small Outline (Narrow 0.50) (LTC DWG # 05-08-60) 0.89 0.97* (.80 5.00) 8 7 6 5 0.228 0.2 (5.79 6.97) 0.50 0.57** (3.80 3.988) 2 3 0.008 0.00 (0.203 0.25) 0.00 0.020 (0.25 0.508) 5 0 8 TYP 0.053 0.069 (.36.752) 0.00 0.00 (0.0 0.25) 0.06 0.050 0.06.270 *DIMENSION DOES NOT ILDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.52mm) PER SIDE ** DIMENSION DOES NOT ILDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.00" (0.25mm) PER SIDE 0.0 0.09 (0.355 0.83) 0.050 (.270) BSC SO8 0695 RELATED PARTS PART NMBER DESCRIPTION COMMENTS LTC 63 Triple High Side Driver for 2-Cell Inputs.8V Minimum Input, Drives N-Channel MOSFETs LT239 Backup Battery Management System Easy-to-se, Fail-Safe Backup Protection LT30 Fixed /2V Step-p Micropower DC/DC Converter 2V/200mA from, 20µA I Q, 88% Efficiency LT302 High Output Current Micropower DC/DC Converter /600mA from 2V, 2A Internal Switch, 200µA I Q LT303 Micropower DC/DC Converter Low-Battery Detector Inactive in Shutdown LTC77 Protected Switch ltralow R DS(ON) Switch: 0.07Ω LT52 300mA, 2µA I Q Low Dropout Regulator 500mV Dropout at Full Load 6 Linear Technology Corporation 630 McCarthy Blvd., Milpitas, CA 95035-77 (08) 32-900 FAX: (08) 3-0507 TELEX: 99-3977 LT/GP 95 0K PRINTED IN SA LINEAR TECHNOLOGY CORPORATION 995