GALFAN Superir Crrsin Prtectin 5% aluminum, 95% zinc
GALFAN General Infrmatin 5% Aluminum, mischmetal (rare earth elements Ce, La), balance zinc ASTM A875/A875M-10 Eutectic Lamellar Micrstructure very thin ally layer with alternating plates f zinc rich and aluminum rich areas creating sacrificial and barrier prtectin against crrsin GF Cating Steel Substrate Surface Appearance N traditinal spangle faint cellular hneycmb structure Lw Cefficient f Frictin very smth surface cnducive t deep draws Physical Prperties Cating Density Thickness Catings Galvanized 0.258 lb/in 3 1 z/ft 2 = 0.00168 G60 = 0.60 z/ft 2, etc. Galfan 0.238 lb/in 3 1 z/ft 2 = 0.00175 GF60=0.60 z/ft 2, etc. Cating GF20 GF30 GF45 GF60 GF75 GF90 Thickness 0.0004 0.0005 0.0008 0.0011 0.0013 0.0016 2
Crrsin Perfrmance Apprximately 50% mre white rust prtectin cmpared t standard Galvanized Duble white rust crrsin prtectin at same z/ft 2 galvanic prtectin Increased red rust crrsin prtectin at same z/ft 2 barrier prtectin Salt spray studies cnducted n Techs prduced Galfan (phts attached) Equivalent Crrsin Prtectin GF20 t G40 GF30 t G60 GF45 t G90 Envirnmental / Cst Benefit Reduced cating weight fr same crrsin perfrmance Reductin in use f zinc resurces Lwer cating cst Reductin f finished gauge by cating thickness can be achieved n many enduses n lss f mechanical/physical prperties, increased ftage per tn Paint Adhesin Excellent paint adhesin Techs-prduced Galfan painted at several lcatins, different paint systems Passed all quality testing withut issue Zinc phsphate pretreatments nt recmmended fr extended runs at this time pssible issues with elevated aluminum in bath under review Cracking / Flaking Perfrmance Very thin ally layer and lamellar micrstructure resists crack prpagatin Lubricity f smth surface resists flaking in frming and drawing applicatins 3
Sustainability Excerpt belw frm EPA Resurce Cnservatin website: http://www.epa.gv/smm/basic.htm Sustainable materials management (SMM) is a systemic apprach t using and reusing materials mre prductively ver their entire lifecycles. It represents a change in hw ur sciety thinks abut the use f natural resurces and envirnmental prtectin. By examining hw materials are used thrughut their lifecycle, an SMM apprach seeks t: Use materials in the mst prductive way with an emphasis n using less; Reduce txic chemicals and envirnmental impacts thrughut the material life cycle; Assure we have sufficient resurces t meet tday s needs and thse f the future. The Case fr a Lifecycle Apprach t Materials Management Hw ur sciety uses materials is fundamental t ur ecnmic and envirnmental future. Glbal cmpetitin fr finite resurces will intensify as wrld ppulatin and ecnmies grw. Mre prductive and less impactful use f materials helps ur sciety remain ecnmically cmpetitive, cntributes t ur prsperity and prtects the envirnment in a resurce-cnstrained future. 4
Galfan and Sustainability Galfan truly epitmizes the gals f SMM Use materials in the mst prductive way with an emphasis n using less and Assure we have sufficient resurces t meet tday s needs and thse f the future thrugh the fllwing: Zinc cnsumptin reduced by fifty percent with, at least, equal crrsin prtectin Equivalent Catings (based n standard ASTM cating weights) GF20 vs. G40 0.20 z/ft 2 Galfan / 0.40 z/ft 2 standard Galvanized GF30 vs. G60 0.30 z/ft 2 Galfan / 0.60 z/ft 2 standard Galvanized GF45 vs. G90 0.450 z/ft 2 Galfan / 0.90 z/ft 2 standard Galvanized Achieve duble the white rust (sacrificial) prtectin at same z/ft 2 Delayed white rust means even greater red rust (barrier) prtectin at same z/ft 2 Reduced electricity cnsumptin fr Galfan bath (lwer melting pint) GF 820 F average bath temperature GI 870 F average bath temperature 6% higher sustained temperature needed versus Galfan Increased zinc usage = increased charging f zinc pigs = increased electricity cnsumptin f bath t maintain temperature In sme cases, reductin in finished gauge (decreased by cating thickness) can increase lineal ftage / square ftage per tn, thereby reducing cnsumptin f ttal weight needed fr a given prject. Examples based n 0.020 x 48.00 100 tn, 61,275 lineal feet G40 cnverted t GF20 Cating thickness change f 0.0003 New finished gauge f 0.0197 New lineal ftage f 62,208 r 1.5% increase G90 cnverted t GF45 Cating thickness change f 0.0007 New finished gauge f 0.0193 New lineal ftage f 63,492 r 3.6% increase 5
22304018.012 GF20-1008 hrs Salt Spray ASTM B117 22311054.0117 G40U - 1008 hrs Salt Spray ASTM B117 6
22304005.0125 GF30-1008 hrs Salt Spray ASTM B117 22311056.0142 G60-1008 hrs Salt Spray ASTM B117 7
22305013.0139 GF45 Acrylic 1008 hrs Salt Spray ASTM B117 220332031.0140 G90 Acrylic 1008 hrs Salt Spray ASTM B117 8
12329026.0545 GF30 1008 hrs Salt Spray ASTM B117 12336057.057 G60 1008 hrs Salt Spray ASTM B117 9
12329031.0688 GF45 1008 hrs Salt Spray ASTM B117 12338019.071 G90 1008 hrs Salt Spray ASTM B117 10
12163050.0142 GF30 White Plyester Paint System 1000 hrs Salt Spray ASTM B117 11
Galfan Prductin Capabilities at The Techs NexTech Gauge: 0.008 t 0.020 Width: 28 t 43 Cating Weights: Surface Treatments: Temper Pass: GF20, GF30, GF45, GF60, GF75, GF90 Oil, SFT (Hexavalent Chrmium), RHS, Acrylic Available in-line n all gauges GalvTech Gauge: 0.014 t 0.046 Width: 28 t 60 Cating Weights: Surface Treatments: Temper Pass: GF20, GF30, GF45, GF60, GF75, GF90 Oil, SFT (Hexavalent Chrmium), RHS Available in-line n all gauges MetalTech Gauge: 0.023 t 0.110 Width: 24 t 52 Cating Weights: Surface Treatments: Temper Pass: GF30, GF45, GF60, GF75, GF90, GF115 Oil, SFT (Hexavalent Chrmium), RHS Nt available n-line Secndary prcessing available all gauges up t 49.5 width 12