Hydraulic Caliper Disc Brakes SF Series 40 0 00 480 460 SF 0 440 40 SF 40 SF 30 SF 1 SF SF 4 400 380 360 340 30 80 60 40 0 00 160 140 10 0 80 60 Brake torque in knm PINTSCH BUBENZER is certified according to DIN EN ISO 01:008 00 100 1400 1600 0 000 00 400 600 800 40 0 Brake disc diameter in mm Reliable High Performance Robust Design Easy Maintenance B1s
Description SF Main Features - Steel Mill Execution Two identical caliper halves, ready for operation, with spring packs set to nominal force and limit switch for release control (heat resistant) Up to mm airgap between linings and brake disc Easy, manual pad wear compensation Organic, non-asbestos linings Special seals for flame-proof liquids Viton seals Options Heat resistant wiring of limit switches Limit switch wear control (special execution) Heat resistant piping Completely piped supports for one or more calipers Hydraulic power units Cleaning pad pplications Hydraulic power unit - Steel Mill Execution Dead man s circuit Stainless steel tank Non flammable oil Oil temperature switch utomatic emergency release system Stainless steel cover The high capacity of these brakes makes them particularly suitable as secondary emergency brakes on main hoists (ladle cranes) Other applications are possible in material hand ling, requiring power and compact design in either direction of rotation, particularly in replacing band brakes Use of the brakes for applications with high duty cycles should be specifically indicated during technical selection procedure Operating Restrictions Brakes of this range are tested both mechanically and hydraulically and are set to nominal force. This setting can only be changed by the manufacturer. Operating conditions other than described in this brochure require the manufacturer s approval and may influence the function of the caliper and its components Please Note We supply a detailed operating manual with every order. Nevertheless, we would point out that brakes are only as safe as the servicing and maintenance performed while they are in operation. The guarantee for the correct functioning of our brakes is therefore only valid if the user adheres to the German DIN standard 1434 part (drum and disc brakes, servicing and maintenance in operation), or to comparable standards in his own country. PINTSCH BUBENZER Service This includes the verification of the brake selection, if required. detailed questionnaire is provided for this purpose. Installation and commissioning on site is possible by PINTSCH BUBENZER service engineers. Drawings as DWG/DXF files for your engineering department are available upon request. Bs
Disc Brake SF Dimensions and technical data Rev. 1-06 Bleeder valve Pressure connection SF30 *) verage friction factor of standard material combination ll dimensions in mm. lterations reserved without notice. Brake torque MBr in Nm = F (kn) x µ x d1 (mm) 7 8 1 3 Data per caliper half Type SF 1 4 30 40 b b3 b4 b b6 b7 b8 b9 b c1 d d6 d7 d8 h1 h h3 l1 l l3 l4min Bolt ø M4 Bolt material.9 Tighten. torque, Nm Contact force F kn 0 0 Op. pressure bar 140 Max. pressure bar 00 Release stroke mm Oil volume l 0,03 Pad surface cm 47 Theor. friction µ* Weight (kg) 00 368 760 1 Brake disc data SF SF1 SF4 SF30 SF40 d1 = 16 4 1 11 8 60 8 17 1 70 0 60 9 0 40 16 4 1 11 8 60 8 17 1 70 0 6 9 0 1 19 480 0 70 0 31 1 30 70 8 34 1 80 640 1 00 1 1 140 10 38 1 400 0 940 40 70 17 0 1 1 160 170 3 0 1 480 37 1 981 0 1 00 M4.9 0 10 00 0,03 47 M30.9 0 40 00 0,03 70 M36.9 300 40 0,00 0 M48.9 6400 400 40 0,0 1360 d-170 mm d-170 mm d-00 mm d- mm d-30 mm d4 = d-40 mm d-40 mm d-4 mm d-60 mm d-700 mm N 6 Please indicate required mounting position. 4 d = Brake disc diameter in mm d1 = Friction diameter in mm d4 = Max. permissible drum or hub diameter in mm b1 = Disc thickness in mm (min. 30) B3
Disc Brake SF 0 Dimensions and technical data Rev. 0-14 C L d4 = d-4 d1 = d-06 d (min. 0mm) ca. 813 + b1 1 3 46 6 17 0 440 d/-117 - b1 140 3 min. ca. 73 + b1 38 60 F7 M4 1 ±0,3 3 ±0,0 46 ±0,3 19 6 0 Brake Torque MBr in Nm = F (kn) x µ x d1 (mm) *) Theor. friction factor of standard material combination ll dimensions in mm lterations reserved without notice min. Data per caliper half Type SF 0 Contact force F kn Operating pressure p bar Max. pressure p max. bar 00 Release stroke mm Oil volume I 0,07 Pad surface cm 10 Theor. friction factor μ* Weight (without bracket) kg ca. 730 d = Brake disc diameter in mm d 1 = Friction diameter in mm d 4 = Max. permissible drum or hub diameter in mm b 1 = Brake disc thickness in mm (min. 30) BX3
Disc Brake SF Hydraulic power unit for one and more calipers (example) Rev. 03-09 d Example: Standard configuration up to 8 SF/SF1 up to 4 SF4 Motor: 4 kw Pump: 1,3 l/min Pressure: bar Tank: 40 l Weight: 11 kg P The flow diagram shows the general arrangement of the hydraulic power unit, including handpump and dead man circuit for emergency manual release of the brakes. The two solenoid valves are switched in parallel (redundancy). fter the nominal pressure is reached, the idler valve switches into idle running. B 170 bar fallend B 3 1 B P R bar P bar 3 M P S ll dimensions in mm lterations reserved without notice N With every order we supply a complete hydraulic and electric diagram according to the order specification. B4s
Piping Samples Disc brakes SF and BSC Rev. 09-0 Example: Piping of one brake unit one hydraulic power unit Equal Tee Distributor Brake Power Unit Pipe Example: Piping of two brake units - one hydraulic power unit Equal Tee Distributor Pipe Brake Equal Tee Power Unit N ttention: For operating two brake units with one power unit please note, that the power unit should be installed between the brakes in the centre to achieve almost equal pipe length on both sides (equal apply time of brakes). B