INTRODUCTION - CASEWORK CONSTRUCTION DETAILS AND SPECIFICATIONS Overview Cabinets Standard cabinet is manufactured to AWI Premium Grade flush overlay construction. Each cabinet is constructed from premium grade lumber and panel product of the species of wood specified. A variety of panels and glues are available to meet just about any environmental, appearance, or durability requirement. Cabinets are framed and fastened using AWI Premium Grade dowel pin construction. Each base cabinet has 3/4 side and bottom panels as well as 3/4 front, top, rear, and intermediate frames, joined together with concealed hardwood dowels and NAUF glue. The front exposed edge is hardwood edgebanded in the same species as the face veneer. Wall and floor cabinets have 1 top panels and wall cabinets also have 1 bottom panels. Toe spaces are 3 deep by 4 high. All door cabinets have a full height removable back panel. Drawer cabinets have an optional split back panel. Sink cabinets have a partial back panel to facilitate plumbing. Open and glazed cabinets have veneered back panels. BASE CABINET DETAIL CABINET SIDE REMOVABLE BACK REAR RAIL DRAWER SUPPORTS -14 GA GALV. TOP RAIL DRAWER LINER DRAWER WITH INTEGRAL SIDES & BACK DOOR FRONT Doors and Drawers Doors and drawers are manufactured to AWI Premium Standards. Solid doors and drawers are 3/4 particle board. Glazed doors are framed and made from the same species as the face veneer. Drawer bodies are 1/2 9-ply Baltic Birch dovetailed at all 4 corners. NAUF 1/2 plywood panels, painted cold rolled steel or stainless steel are other drawer body options available. Drawer bottoms are 1/4 hardboard or veneered panel that are let into routed slots on all four sides of the drawer body and hot glued along the entire perimeter on the bottom. Drawers and doors are edgebanded with hardwood of the same species as the face veneer. Hardware Doors that are 48 high and higher have at least three hinges and doors that are less then 48 high have two hinges. Standard hinges include five knuckle stainless steel hinge, three knuckle barrel hinge, and concealed European style hinge. Drawer suspension is 100# nylon tire or 100# full extension. File drawers are always 150# full extension. Glazed doors are 1/4 clear laminated safety glass or float glass held in place with a removable brown plastic retainer. Sliding doors shall be set in an extruded aluminum track. ROLLER CATCHES Shelves All shelves are made from veneer core panel product of the same species specified for the face veneer. Shelves 36 or less in width are 3/4 thick and shelves greater than 36 wide are 1 thick. Shelves are adjustable on 1-1/4 increments and held in place via single pin supports or seismic plastic twin pin supports. The front is hardwood edgebanded in the same species as the face veneer. Table Frames and Apron Panels Frames are 3-3/4 high and 3/4 thick lumber. Legs are 2 by 2 solid lumber with 2-1/2 high flexible shoes. Frames are bracketed and securely bolted together. HINGE (See Page H7) DRAWER FRONT BOTTOM ADJUSTABLE SHELF ENCLOSED TOE SPACE FSC certified sustainable materials and no added urea-formaldehyde (NAUF) are available options. Mott Maufacturing wood casework division is working towards registering to the ISO 9001-2008 standard. H1
INTRODUCTION - TYPICAL WORK AREAS Details The following details are provided to illustrate how base cabinets, filler panels and countertops combine to construct a laboratory work area. 60" 1524mm 12 11-1/2" 292mm 18 Or 71mm 60" 1524mm 1" 22" 14" 25.4mm 559mm 356mm 22" 559mm 1" 25.4mm 1" 25.4mm 22" 14" 559mm 356mm 22" 559mm 1" 25.4mm 30", 33 & 36" Or 762mm, 838mm & 914mm 30", 33 & 36" Or 762mm, 838mm & 914mm Above is an island type configuration with 60 wide counter top, (2) 22 deep cabinets, a 14 removable filler panel and 12 reagent shelf. The area covered by the 14 removable filler panel provides a large accessible space for required services. Both base cabinet side panels can also be extended to 29 deep to eliminate the use of a 14 filler and provide a continuous cabinet look, cabinet interior will remain 22 deep. Above is an island type configuration with 60 wide counter top, (2) 22 deep cabinets, and a 14 removable filler panel. The area covered by the 14 removable filler panel provides a large accessible space for required services. Both base cabinet side panels can also be extended to 29 deep to eliminate the use of a 14 filler and provide a continuous cabinet look, cabinet interior will remain 22 deep. 24" 609mm 30" 762mm 25.4mm 7" 22" 1" 1" 22" 1" 559mm 177.8mm 25.4mm 559mm 25.4mm 30", 33 & 36" Or 762mm, 838mm & 914mm 30", 30 & 36" Or 762mm, 838mm & 914mm Above is a standard base cabinet configuration with 24 deep counter top, 22 deep base cabinet and 1 filler panel. Base cabinet side panels can also be extended to 23 deep to eliminate the use of a 1 filler and provide a continuous cabinet look, cabinet interior will remain 22 deep. Above is a base cabinet configuration with 30 deep counter top, 22 deep base cabinet and 7 removable filler panel. The area covered by the 7 removable filler panel provides accessible space for required services. Base cabinet side panels can also be extended to 29 deep to eliminate the use of a 7 filler and provide a continuous cabinet look, cabinet interior will remain 22 deep. H2
INTRODUCTION - OPTIONAL METRIC SIZES Base Cabinets Mott base cabinets are also available in metric widths of 513mm or 1000mm. The information below indicates the dimensions of metric base cabinets. To order metric base cabinets contact your nearest Mott dealer. 883mm (standing height) or 730mm (sitting height) 883mm (standing height) or 730mm (sitting height) 513mm 1000mm 559mm or 457mm Note: 457mm available on selected specialty cabinets only. Wall Cabinets Mott wall cabinets are also available in metric widths of 513mm or 1000mm. The information below indicates the dimensions of metric wall cabinets. To order metric wall cabinets contact your nearest Mott dealer. 1219mm 914mm 762mm 610mm 1219mm 914mm 762mm 610mm 513mm 1000mm 356mm 457mm H3
INTRODUCTION - OPTIONAL METRIC SIZES Floor Cabinets Mott floor cabinets are also available in metric widths of 513mm or 1000mm. The information below indicates the dimensions of metric floor cabinets. To order metric floor cabinets contact your nearest Mott dealer. 2133mm 2133mm 513mm 1000mm 457mm or 559mm Aprons and Tables Mott aprons and tables are also available in metric widths of 513mm, 1000mm and 1513mm. The information below indicates the dimensions of metric aprons and tables. To order metric aprons and tables contact your nearest Mott dealer. 883mm 730mm 513mm 1000mm 1513mm 559mm 711mm Miscellaneous Items Mott miscellaneous items such as filler panels, service drops etc. are also available in metric widths. To order these items contact your nearest Mott dealer. H4
Standard Options OVERLAY STYLE: REVEAL OVERLAY Standard No notching on doors with balanced reveals. GRAIN DIRECTION: LIPPED OVERLAY Lipped Overlay cabinet fronts have a combination grain direction. FULL FLUSH OVERLAY Flush Overlay cabinet fronts provide tight reveals by notching around the hinge. VERTICAL MATCHED Standard Both drawers and doors have a vertical matched grain direction. CABINET CORE: COMBINATION Drawer grain direction is horizontal and door grain direction is vertical. VENEER CORE PLYWOOD Standard On the sides and bottom. PARTICLEBOARD CORE PLYWOOD On the sides and bottom. REMOVABLE BASE CABINET BACK PANEL: ONE PIECE Standard One piece behind cupboard units. Open behind drawers. TWO PIECE Allows for easy access to portions of the cabinet. CABINET TOP FRAME: FRONT AND BACK RAILS Standard Front horizontal and rear vertical rail. EDGEBANDING: ROLL TYPE EDGE BAND Standard 100% hardwood. FULL TOP FRAME Front, rear and side vertical rails. STICK EDGE BAND 1/8 thick. STICK EDGE BAND 1/4 thick. H5
Standard Options FIXED BACK AT TALL CASE/WALL CASE/UPPER CASE ONLY (solid doors only): TEMPERED HARDBOARD Standard BASE - CONSTRUCTION: INTEGRAL WITH END PANELS, WITHOUT LEVELERS Standard VENEER MDF CORE PLYWOOD INTEGRAL WITH END PANELS, WITH LEVELERS VENEERED BACK SEPARATE Factory attached or field furnished/ fabricated FINISHES: SEFA 8 Standard DRAWER CONSTRUCTION: OTHER DOVETAIL DRAWER BODIES Standard All four wood sides connected by multiply dovetail joints. Sides slotted for bottom panel. DRAWER SUSPENSION: PAINTED STEEL DRAWER BODIES One full piece of powder coated 20ga rolled steel with reinforcing bend on all top edges. STAINLESS STEEL DRAWER BODIES Drawer with integral sides and back, constructed using 20ga 304 stainless steel with a number 4 finish. FULL EXTENSION SLIDES Standard OPTION 01 for full extension 100 lb, 14ga galvanized steel slides. BASE CABINET SHELF DEPTH: 3/4 EXTENSION SLIDES Standard 3/4 extension 14ga galvanized steel slides. FULL EXTENSION SLIDES OPTION 25 for 150lb OPTION 26 for 200lb FULL DEPTH SHELF Standard Spans from back panel to door. SHELF CLIPS: HALF DEPTH SHELF Accommodates storage of tall apparatus in front of shelf. SPLIT DEPTH SHELF Capable being a Half Depth and a Full Depth shelf. GLASS: PLASTIC TWIN-PIN Standard Seismic Suited. FLOAT GLASS Standard 3mm glass with ground flush pull. PLATED PIN AND SOCKET Allows for easy adjustability. LAMINATED SAFETY GLASS 6mm TEMPERED SAFETY GLASS 6mm H6
Standard Options DRAWER/DOOR PULL DIRECTION: CONFIGURATION 1 Standard Pulls are horizontal on all drawers, and vertical on all doors. CONFIGURATION 2 Pulls are horizontal on all drawers and doors. Floor cabinets have vertical pulls. DRAWER/DOOR PULLS: OPTION 62 - Standard 4 Brushed Aluminum Pull DOOR HINGES: OPTION 61 4 Tubular Stainless Steel Pull OPTION 68 4 Aluminum Wire Pull OPTION 6B 4 Black Wire Pull OPTION 63 4 Chrome Pull OPTION 60 4 Black Nylon Pull OPTION 20 - Standard Dull Chrome Overlay Hinge OPTION 24 Stainless Steel Overlay Hinge OPTION 2A Black Overlay Hinge OPTION 27 Three Knuckle Hinge OPTION 28 165 Degree Euro Concealed Self-Closing Hinge LOCK TYPE: OPTION 30 Standard 5-Disc Master with removable core OPTION BS 5-Pin Master, 8 week lead time. FRONT RAILS & SECURITY PANELS: WITHOUT FRONT RAILS Standard When no locks are selected. DOOR CATCHES: WITH FRONT RAILS When cabinets are to be keyed alike. WITH FRONT RAILS & SECURITY PANEL When cabinets are to be keyed different. ROLLER CATCH Standard LABEL HOLDER: MAGNETIC CATCH NONE Standard OPTION 02 Stainless Steel label holder - one per door, one per drawer head H7
Ordering Special Features STEP TWO - OPTIONAL FEATURES Select any of the following options as the application requires. Option # Description Cabinet & Miscellaneous Options 00 Required cabinet has drawer and/or door configuration similar to basic part noted. A minor configuration change is required with no changes in the cabinets outside dimensions from the basic part number specified - see note 1 02 Label holders on all doors/drawers 03 Numeric or alpha identification disks on all doors/drawers - see note 2 04 Standard louver configuration on doors - see note 3 05 Non-standard louver configuration on doors - see note 1 06 One table non-removable shelf 07 Cut-outs for electrical and/or plumbing services - see note 1 08 Security panel installed in cabinet complete with locks - see note 14 09 Stainless steel waste flap 10 One drawer divider per drawer - see note 12 11 Multiple drawer dividers per drawer - see note 1 12 Pull out writing board 13 Pull out writing board with high pressure laminate writing surface 14 Ventilation grill in toe kick base - see note 1 15 Finished back on cabinet 17 Nylon coated levelers 19 Full width drawer on 5 high apron 48 Keyboard tray (replace drawer) 82 FRP liner for acid cabinets - see note 4 83 Self closing and latching doors for solvent cabinets 84 Galvanized bin insert 85 PVC bin insert- see note 7 89 Lazy susan storage unit for corner cabinets 90 Sink supports - see note 6 BL Base Label (use this option code to replace standard label on Acid cabinets) DL Fluorescent light for specialty recessed drawer desk unit DA 1 Double angle F1 Finished top F2 Finished top and back FL Fusible Link for Insulated Solvent Unit - see note 7 LA Bilingual label (English/French) LF Longitudinal file NB No base on cabinet NF No cabinet floor and toekick is integral with door PC Foot pedal cutouts centered PL Foot pedal cutout left hand side PR Foot pedal cutout right hand side PP Pre-plumbed (option code not to be used for fume hoods) PW Pre-wired (option code not to be used for fume hoods) RB Removable back on drawer cabinet RL Remote LED light for narcotic cabinet SK Skid item H8
Ordering Special Features STEP TWO - OPTIONAL FEATURES Select any of the following options as the application requires. Option # Description Cabinet & Miscellaneous Options SP Silk Screen Printing (to replace standard labels on Acid and/or Flammable cabinets) VK Corrugated polyolefin vent kit for acid cabinets WS Supply hose to hook up with facility water supply XL7 Left side of base cabinet to be extended 7 XR7 Right side of base cabinet to be extended 7 XB7 Both sides of base cabinet to be extended 7 Wall Cabinet Options SL ZR DS FR HR Seismic lip Z mounting rail Double sided wall cabinet Hang wall cabinet on Sigma Flex style systems Add hanging rail to cabinet Floor Cabinet Options 80 Full height doors for wardrobe unit for floor cabinets 81 Coat rod for wardrobe for floor cabinets Shelf Options AR Rear shelf angle AF Front shelf angle AB Front and rear shelf angle 40 One extra cabinet shelf - see note 5 41 Two extra cabinet shelves - see note 5 42 One interior cabinet shelf on pull-out runners - see note 13 43 Two interior cabinet shelves on pull-out runners - see note 13 44 Three interior cabinet shelves on pull-out runners - see note 13 Glass Options 45 DuoLite safety glass - see note 11 46 Tempered glass - see note 11 47 Customer specified glass - see note 11 4A Glass Tint 44% (Grey Smoke) Removable Base Options 70 Removable base - front toe kick - see note 15 71 Toe kick - front & left side - see note 15 72 Toe kick - front & right side - see note 15 73 Toe kick - front & 2 sides - see note 15 74 Toe kick - front & back - see note 15 75 Toe kick - front, back, & 2 sides - see note 15 76 Replace toe kick base with 4 legs 77 Replace cabinet toe kick base tip proof casters 78 Replace cabinet toe kick base with customer specified casters 79 Other customer specified base and/or toe kick - see note 1 H9
Ordering Special Features STEP TWO - OPTIONAL FEATURES Select any of the following options as the application requires. Option # Description Table Options 48 Keyboard tray (replaces drawer) 49 Adjustable height legs. Legs are adjustable in 1 increments, from 28-3/4 high to 34-3/4 high (work top not included). 87 Mobile table complete with casters - see note 10 88 Mobile table complete with customer specified casters 91 Table with no supports 92 U frame style table with rear & side supports 93 Left side leg table - no supports 94 Right side leg table - no supports 95 Front table legs - no supports HU U frame table with floating rail to hang cabinets EXPLANATORY NOTES FOR OPTION CODES 1. Full dimensional and descriptive details (preferably including a sketch) must be included with the order. 2. Full descriptive details must be included with the order. 3. Standard louver configuration is one block of 6 louvers located near the bottom center of each door, each louver is approximately 3 inches wide by 5.5 inches long. 4. Use this option code to have cabinet lined with FRP instead of molded liner. 5. Standard number of removable shelves per base cabinet with door(s) or wall cabinet is noted in the cabinet drawings of this catalog. 6. Sink support kit is required for under-counter mounted sinks used with Imperial Stone or Epoxy counter tops. Sink support kit not normally required for self rimming or integrally welded sinks. 7. Designed for use on solvent cabinets with self-closing option (-83). A fusible link holds doors open during use and melts at 165 F to automatically close doors in the event of a fire. 8. Provide complete specification and source for all special option ordered. 9. Standard lock is cam lock. Every lock on every cabinet on order will be keyed alike unless otherwise specified. 10. Standard 4 high casters are swivel with rolling brake. 11. Standard glass is as follows: All framed glass and sliding glass Floor Cabinets 1/4 (6mm) float glass Sliding glass door Wall Cabinets 1/4 (6mm) float glass Framed glass door Wall Cabinets 1/8 (3mm) float glass 12. Drawer divider runs depth of drawer. 13. Pull-out shelves replace standard removable shelf in base cabinets with door(s). 14. Lock option must be specified from cabinet locking options section. 15. Cabinet left and right are determined when facing the cabinet front. H10
Ordering Double Sided Wall Units Mott laboratory furniture is available with a wide variety of features to meet specific application requirements. The full range of our Mott wall cabinets are available in our double sided design. To specify double sided wall cabinets, select the two digit part number suffix from below and add this suffix after the standard part number, separated with a dash. OVERVIEW EXAMPLE To order double sided wall cabinets. 5410060W-DS Double sided wall cabinet option Wall cabinet - 30 high from page K4 Note: Steel cabinet drawings shown. 5410060W 5410060W-DS Ordering Special Features Mott laboratory furniture is available with a wide variety of features to meet specific application requirements. To specify any feature, select the two digit part number suffix from the list below and add this suffix after the standard part number, separated with a dash. OVERVIEW EXAMPLE To order chrome hinges, brushed aluminum pulls, and a pull-out shelf on a drawer/door cabinet. 1410022W-21-62-42 HOW TO SPECIFY FEATURES One interior cabinet shelf on pull out runners - page H9 Brushed aluminum pulls - page H7 Chrome hinges - page H7 Base cabinet - standing height from page I1 Two steps are required to specify the chosen option for each furniture component. If dimensional changes are required please see section "Ordering Special Features; Non-Standard Sizes" on page H12. H11
Ordering Double Sided Wall Units NON-STANDARD SIZES Specifying the part number of a non-standard size for a cabinet, table, and miscellaneous items is accomplished through the following steps: 1. Identify the required product configuration from the catalog drawings. 2. Identify the next largest or the largest standard product size from the catalog charts. 3. Identify the standard part number from steps 1 and 2 above. 4. Determine the non-standard part number by placing S at the beginning of the standard part number identified in 3 above. 5. After the non-standard part number, list options required according to the special features ordering codes in the Ordering Special Features section. 6. After the non-standard part number that includes all option codes, list in the noted sequence, the product s required: Width, Height, Depth Part numbers that relate to imperial units will have dimensions noted in inches, to the nearest quarter of an inch and noted to two decimal places. Part numbers that relate to metric units will have dimensions noted in millimeters. S-1510093W(W44)-23-61-01-42 One interior cabinet shelf on pull-out runners Full extension drawer runners Stainless steel wire pulls Stainless steel hinges Non-standard width of 44 inches (next larger size specified) standard height and depth 48" wide standing height base cabinet - Additional Info noted by "S" H12