RF-TVMP20 TV Wall Mount For wood-stud and concrete wall installations Safety information and specifications...2 Tools needed...2 Package contents: parts...3 Package contents: hardware...4 Installation instructions...5 Assembly Guide Before using your new product, please read these instructions to prevent any damage.
Safety information and specifications IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS CAUTION: Do not use this product for any purpose not explicitly specified by Rocketfish. Improper installation may cause property damage or personal injury. If you do not understand these directions, or have doubts about the safety of the installation, contact Customer Service or call a qualified contractor. Rocketfish is not responsible for damage or injury caused by incorrect installation or use. The included hardware is designed for use on vertical walls constructed of wood studs or solid concrete. A wood stud wall is defined as consisting of a minimum of 2x4 wooden studs (2 wide by 4 deep) with a maximum of 5/8 drywall. The included hardware is not designed for use with metal studs or cinderblock walls. If you re uncertain about the construction of your wall, then please consult a qualified contractor or installer for assistance. For a safe installation, the wall you are mounting to must support 4 times the weight of the total load. If not, then the surface must be reinforced to meet this standard. The installer is responsible for verifying that the wall structure and hardware used in any installation method will safely support the total load. The weight of your TV must not exceed 20 lbs. (9.1 kg). Rocketfish recommends that the wall be capable of supporting five times the weight of your TV and wall mount combined, or approximately 125 lbs. (57 kg). This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children! Tools needed You will need the following tools to assemble your new TV wall mount: Maximum TV weight: 20 lbs. (9.1 kg) Minimum TV weight: 7 lbs. (3.2 kg) Maximum TV Screen size: 32 in. diagonal Overall dimensions (W H ): 2.9 x 7.2 in. (7.3 x 18.3 cm) Wall-mount weight: 5 lbs. (2.27 kg) We re here for you www.rocketfishproducts.com For customer service, call: 1-800-620-2790 (U.S. and Canada) or 01-800-926-3010 (Mexico) Pencil Level Edge-to-edge stud finder Phillips screwdriver Drill Measuring tape 7/32" (5.5 mm) wood drill bit for wood stud wall OR 3/8" (9.5 mm) masonry drill bit (concrete only) Socket wrench with 1/2" (13 mm) socket or adjustable wrench Hammer 2
Package contents: parts Make sure that you have all the parts necessary to assemble your new TV wall mount: F Threaded cap (1) D Top cover (1) C Adapter (4) B Arm assembly (1) A Wall plate (1) E Bottom cover (1) 3
RF-TVMP20_13-0707_MAN_V2_ENG.fm Page 4 Wednesday, July 10, 2013 6:23 AM RF-TVMP20 TV Wall Mount Package contents: hardware Make sure that you have all the hardware necessary to assemble your new TV wall mount: TV Hardware Bag Label M-A M-B M-C Hardware M4 12 mm screw M5 12 mm screw Qty. Label 4 P-E 4 M6 12 mm screw Hardware 2 Cable tie Washer P-F Qty. 1 4 W-A 2 5/16" 2 3/4" lag bolt P-A 1 4 mm Allen wrench W-B 2 Concrete anchor P-B 1 2.5 mm Allen wrench M8M5 KIT P-C 4 Adapter kit 1 M6 x 60 mm screw P-D 4 M5 7 mm screw 1 10 4 20 2 30 40 50 3 60 70 4in 80 90 100mm
Installation instructions STEP 1- Select screws 1 Select the screws for your TV. A limited number of TVs come with mounting hardware included. (If there are screws that came with the TV, they are usually in the holes on the back of the TV.) If you don't know the correct diameter of the mounting screws your TV requires, test various sizes by hand threading the screws. Select one of the following types of screws: M4 12 mm screws (M-A) M5 12 mm screws (M-B) M6 12 mm screws (M-C) NOTE: For Samsung TVs with size M8 mounting holes, use the hardware included in the Adapter Kit. Follow the instructions printed on the Adapter Kit bag to install the hardware. CAUTION: To avoid potential personal injuries and property damage, make sure that there are adequate threads to secure the brackets to your TV. If you encounter resistance, stop immediately and contact customer service. Using hardware that is too long may damage your TV. However, using a screw that is too short may cause your TV to fall from the mount. Screw fits correctly Screw is too long Screw is too short 2 Remove the screws. 5
STEP 2 - Determining your mounting configuration 1 Carefully place your TV screen face down on a cushioned, clean surface to protect the screen from damage and scratches. 2 If your TV has a table top stand attached, remove the stand. See the documentation that came with your TV for instructions. 3 Temporarily hold the flat surface of the arm assembly (B) against the back of your TV. 4 Identify the type of mounting configuration by determining if your arm assembly (B) lines up with the screw holes on the back of your TV or if you will need to install the adapters (C). 5 Remove the arm assembly. 100mm (3-15/16 ) 75mm (2-15/16 ) 75 x 75mm 100 x 100 mm 100mm (3-15/16 ) 75mm (2-15/16 ) 100mm (3-15/16 ) 100 x 200 mm 200mm (7-7/8 ) 200mm (7-7/8 ) 200 x 200 mm 200mm (7-7/8 ) 200mm (7-7/8 ) 200 x 100 mm 100mm (3-15/16 ) For 75 x 75mm or 100 x 100 mm mounting configurations, go to "STEP 3: Option 1- Attaching the arm assembly without the adapters" on page 7. -OR- For a 100 x 200 mm, 200 x 200 mm, or 200 x 100 mm configuration, go to "STEP 3: Option 2 - Attaching the adapters to the arm assembly" on page 8. 6
STEP 3: Option 1- Attaching the arm assembly without the adapters 1 Align the arm assembly (B) with the screw holes on the back of the TV. 2 Install screws (M-A, M-B, or M-C) securely into the four holes in the back of the TV. Do not over-tighten. Note: The arm assembly (B) should be level on the back of the TV. Proceed to Step 4 Determine wall mount location. 75 x 75mm 100 x 100mm 100mm (3-15/16 ) 75mm (2-15/16 ) 100mm (3-15/16 ) 75mm (2-15/16 ) TV B M-A OR M-B OR M-C Screws OR OR M-A (4) M-B (4) M-C (4) Level Phillips screwdriver B Arm assembly 7
STEP 3: Option 2 - Attaching the adapters to the arm assembly 1 Install the four adapters (C) onto the arm assembly (B) using four M5 x 7mm screws (P-D). Do not over-tighten. 2 Adjust the adapters (C) to fit your TV configuration, determined in Step 2. B P-D C 100 x 200 mm 200 x 200 mm 200 x 100 mm P-D (4) Phillips screwdriver B Arm assembly C Adapters (4) 8
STEP 3: Option 2 - Attaching the arm assembly with adapters 3 Align the adapters (C) with the screw holes on the back of your TV. 4 Install screws determined in Step 1 (M-A, M-B, or M-C) securely into the four holes in the back of the TV. Do not over-tighten. 5 Proceed to Step 4 Determine wall mount location. Note: The arm assembly (B) should be level on the back of the TV. C TV B M-A OR M-B OR M-C Screws OR OR M-A (4) M-B (4) M-C (4) Level Phillips screwdriver B Arm assembly C Adapters (4) 9
STEP 4 - Determine wall-mount location Note: For more detailed information on determining where to drill your holes, visit our online height-finder at: http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder Your TV should be high enough so your eyes are level with the middle of the screen. Normally, 40 to 60 inches from the ground. When your television is in a position closest to the wall and the arm assembly is horizontal, the center of your television will be 13" to the left or right of the center of the wall plate (A). Before you drill holes in the wall: 1 Measure the distance from the bottom of your TV to the middle (half of the height of the TV). This is measurement a. 2 Measure the distance from the floor to where you want the bottom of the TV to be positioned on the wall when the arm assembly is horizontal. Keep in mind that this TV mount allows for 13" of travel in all directions from the center of the wall plate. Your TV should be mounted in a position that will not cause it to come in contact with furniture, or items placed on top of furniture (like a Blu-ray player or cable box). This is measurement b. 3 Add a + b. This measurement is the height where you want the center of your TV to be. 4 Measure 13" to the left OR right of the a + b measurement position. This will be the desired position for the center of the wall plate. This is measurement c. 5 Use a pencil to mark this spot on the wall. 13 13 c c a b Measuring tape Pencil 10
STEP 5 - Option 1: Installing on a wood stud wall Note: Any wallboard or material covering the wall must not exceed 5/8" (16 mm). 1 Locate the stud. Verify the center of the stud with an edge-to-edge stud finder. 2 Align the wall plate (A) at the height you determined in the previous step and make sure that it is level. Use a pencil to mark the lag bolt hole locations (2) on the stud centers. Remove the wall plate. 3 Drill pilot holes to a depth of 2-3/4 in. (70 mm) using a 7/32 in. (5.5 mm) diameter drill bit. 4 Align the wall plate (A) with the pilot holes, insert the lag bolts (W-A) through the holes in the wall plate, then tighten the lag bolts only until they are firm against the wall plate. CAUTION: Avoid potential injuries or property damage! DO NOT over-tighten the lag bolts (W-A). Center pencil mark made in Step 1. W-A A 2-3/4 in. (70 mm) W-A (2) Level A Wall plate Edge-to edge stud finder Drill Pencil 1/2" socket wrench 7/32" wood drill bit 11
RF-TVMP20_13-0707_MAN_V2_ENG.fm Page 12 Wednesday, July 10, 2013 6:23 AM RF-TVMP20 TV Wall Mount STEP 5 - Option 2: Installing on a solid concrete wall 1 2 3 4 Align the wall plate (A) at the height you determined in the previous step and make sure that it is level. Use a pencil to mark the lag bolt hole locations (2). Remove the wall plate. Drill pilot holes to a depth of 2-3/4 in. (7 mm) using a 3/8 in. (10 mm) diameter masonry drill bit. Insert the concrete wall anchors (W-B) into the pilot holes and use a hammer to make sure the anchors are flush with the concrete surface. Align the wall plate (A) with the anchors, insert the lag bolts (W-A) through the holes in the wall plate, then tighten the lag bolts only until they are firm against the wall plate. CAUTION: Avoid potential injuries or property damage! DO NOT over-tighten the lag bolts (W-A). 2-3/4 in. (70 mm) A W-B W-A W-A (2) W-B (2) 12 Level A Wall plate 3/8" masonry drill bit Edge-to edge stud finder 1/2" socket wrench Pencil Drill Hammer
STEP 6 - Attach your TV to the wall plate 1 Holding the TV level, with the screen parallel to the wall. Place the arm assembly (B) over the wall plate (A) as shown below. 2 Place the theaded cap (F) over the wall plate (A) and install the washer (P-F) and M6 x 60 mm screw (P-C). HEAVY! You will need assistance with this step. P-C (1) Level F Threaded Cap P-F (1) Phillips screwdriver 13
STEP 7 - Installing the covers and cable ties 1 Install the top and bottom covers (D & E) onto the wall plate (A). 2 Connect the cable to your TV, then secure the cable to the underside of the arm assembly (B) with two cable ties (P-E). D P-E E P-E Cable ties (2) D & E Wall plate covers 14
STEP 8 - Adjusting the vertical position, the tilt, and the horizontal position Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before adjusting. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffcult or if product does not stay in desired position, follow the adjustment instructions to create smooth and easy movements. NOTE: Depending on your product and the type of adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation. 1 To increase or decrease the lift tension setting, use the 4mm Allen wrench (P-A). 2 To increase or decrease the tilt tension setting, use the 4mm Allen wrench (P-A). 3 Using the 2.5mm Allen wrench (P-B) adjust the tension of the horizontal movement. If this product moves too easily from side-to-side, increase the tension (+). If the product is too difficult to move from side-to-side, decrease the tension (-). Adjusting the factory-set tension Increase If TV weight exceeds product s factory setting, it won t stay up when raised. To prevent TV from sagging downward, increase tension setting. 1 P-A Decrease If TV weight is lower than product s factory setting, it won t stay down when lowered. To prevent TV from drifting upward, decrease tension setting. 2 3 P-A 4 mm Allen wrench P-B 2.5 mm Allen wrench For customer service, call: 1-800-620-2790 (U.S. and Canada) or 01-800-926-3010 (Mexico) 15
www.rocketfishproducts.com 1-800-620-2790 (U.S. and Canada) or 01-800-926-3010 (Mexico) Distributed by Best Buy Purchasing, LLC 7601 Penn Avenue South, Richfield, MN 55423-3645 USA 2013 BBY Solutions, Inc. All rights reserved. ROCKETFISH is a trademark of BBY Solutions, Inc. All other products and brand names are trademarks of their respective owners. Part number: 888-61-044-W-01 V2 ENGLISH 13-0707