TECHNICAL SPECIFICATIONS Model: IDT20 Generator set with manual or automatic control panel. Image for guidance purposes. ENGINE MAKE DEUTZ F3M 2011 CONTINUOUS POWER: (PRP Prime Power norma ISO 8528-1) 20 kva ALTERNATOR MECC-ALTE ECO 28-1L/4 STAND-BY POWER: (LTP Limited Time Power norma ISO 8528-1) 22 kva Amperes in the different voltages: VOLTAGE HZ PHASE COS Ø PRP KVA/KW LTP KVA/KW AMPERAGE 415/240 50 3 0,8 20/16 22/18 30,64 400/230 50 3 0,8 20/16 22/18 31,79 380/220 50 3 0,8 20/16 22/18 33,47 240/139 50 3 0,8 20/16 22/18 52,99 230/133 50 3 0,8 20/16 22/18 55,29 220/127 50 3 0,8 20/16 22/18 57,8
ENGINE CHARACTERISTICS MAKE DEUTZ F3M 2011 GENERAL DATA Power PRP (kwm) Power LTP (kwm) No. cylinders Cylinder capacity (L) Diameter per stroke (mm) Compression ratio Cooling system Injection Suction Series regulator Steering wheel coupling 19.00 20.40 3-94 x 112 19 OIL DIRECT NATURAL MECHANICAL - Lubrication system Oil capacity (L) Oil consumption (%) Min. alarm oil pressure (bar) 5 0.30 1.50 Ventilation system Air cooling flow (m3/h) Combustion air flow (m3/h) Max. back pressure for fan (mbar) 1800 122 0 Exhaust system Exhaust gas flow (m3/h) Exhaust back pressure (mbar) Temp. exhaust gases (ºC)) 337 30 599 Electrical system VDC (V) Battery (Ah) Engine start-up (kw) 12 70 3
ALTERNATOR CHARACTERISTICS MECC-ALTE ECO 28-1L/4 GENERAL DATA Power PRP (kva) Power LTP (kva) Efficiency Alt. 3/4 % Efficiency Alt. 4/4 % No. Poles Voltage regulator No. wires Insulation Xd (%) X d (%) X Degree of protection 20.00 22.00 88.00 87.60 4 DSR 12 H 175.00 16.50 9.40 IP23 GENERATOR SET CONSUMPTION % POWER USED LITRES/HOUR 50% 3.20 75% 4.70 100% 6.70 DIMENSIONS, CAPACITIES AND APPROXIMATE WEIGHT DIMENSIONS (MM) LENGTH WIDTH HEIGHT 1400 760 1560 FUEL TANK (LITRES) 67 WEIGHT (KG) 540.00
INMESOL GENERATOR SET GENERAL DESCRIPTION The INMESOL generator set is an electrical energy generating machine which is used in places where there is no mains supply or when there is a MAINS failure. The mobile elements, distribution belt, fan, etc., and those parts which reach high temperatures during operation, exhaust manifold, etc, include their corresponding protections, in compliance with the requirements of the Machinery Directive 2006/42. REGULATIONS The machine holds the CE marking, and the corresponding Declaration of Conformity is issued with each of them, in which it specifies that the machine complies with R.D 842/2002 Low Voltage Regulations and with the European Directives: 2006/42 on Safety in Machinery. 2006/95/CE on Electrical Safety. 2004/108/CE on Electromagnetic Compatibility. 2005/88/CE on NOISE EMISSIONS by equipment for outdoor use (for SOUNDPROOF GENERATOR SETS).
IN INDUSTRIAL GENSETS / SCOPE OF SUPPLY ENGINE/ALTERNATOR MONOBLOC DIRECTLY CONECTED AND INSTALLED VIA SILENT BLOCKS ON A FRAME MADE FROM HIGH TENSILE ELECTRO WELDED STEEL PROFILES THAT ARE TREATED WITH DEGREASING LIQUIDS AND APLICATED WITH A ZINK COAT AND EPOXI PAINT. CANOPY OF STEEL SHEET SOUND PROOFED WITH FIREPROOF ROCKWOOL, AND TREATED WITH DEGREASING LIQUIDS AND APLICATED WITH A ZINK COAT AND EPOXI PAINT. FUEL TANK INTEGRATED IN THE CHASSIS PROVIDED WITH FUEL LEVEL METER AND FUEL LINES TO THE ENGINE. ENGINE WITH MECHANICAL ENGINE DRIVEN PUSHER FAN. OPEN SOUNDP. INDUSTRIAL SILENCER WITH -15 db(a) NOICE REDUCTION AND EXHOUST OUTLET TUBE. RESIDENCIAL SILENCER WITH -35 db(a) NOICE REDUCTION WITH EXHAUST TUBE AND PROTECTION CAP. ELECTRIC CONTROL CUBICLE WITH CONTROL MODULE INCLUDING PROTECTION AND READING OF ELECTRICAL MEASSURES ENGINE INSTRUMENTATION FUEL LEVEL AND ENGINE RUNNING HOURS ETC. 4 POLE TERMAL AND MAGNETIC CIRCUIT BREAKER and TERMAL AND MAGNETIC CIRCUIT BREAKER AND EARTH FAULT RELAY BATTERY CHARGE ALTERNATOR. STARTER BATTERY COMPLETE WITH CABLES TO THE ENGINE POLE PROTECTION. INSTALLATION PREPARED FOR EARTHING SPIKE (SPIKE NOT INCLUDED) SECURITY PROTECTION FOR HOT AND MOVING PARTS AS WELL AS LIVE ELECTRICAL COMPONENTS. EMERGENCY STOP PUSH BUTTON IN THE EXTERIOR. MANUAL ENGINE OIL EXTRACTION PUMP SELF EXCITED AND AUTO REGULATED ALTERNATOR. INTEGRATED LIFTING HOOK FOR SINGLE POINT LIFTING WITH CRANE, GENSETS UP TO 450 KVA. PREPARED FOR CONECTION OF OPTIONAL EXTERNAL EXTRA LARGE FUEL TANK INCLUDING BUNDED BASE FRAME FOR PROTECTION AGAINST LEAKS TO AMBIENCE. THE CHASIS IS PREPARED FOR THE INSTALATION OF A TRAILER KIT. STANDARD ELECTRONIC SPEED GOVERNOR ON ENGINES FROM 220 KVA AND UP.
OPEN SKID GENERATOR SETS DSE 3110 MANUAL CONTROL PANEL DSE 3110 MANUAL CONTROL PANEL MANUAL CONTROL, PROTECTION AND DISTRIBUTION panel, assembled on the generator set in metal cabinet with a DSE 3110 engine protection unit. Image for guidance purposes. CONTACT US FOR DETAILED DATA SHEETS AND OTHER CONTROL PANEL OPTIONS
OPEN SKID GENERATOR SETS DSE 6020 AUTOMATIC CONTROL PANEL DSE 6020 AUTOMATIC CONTROL PANEL PROTECTION, DISTRIBUTION AND AUTOMATIC CONTROL panel which starts the generator set when it detects a mains failure and stops it when the mains is restored with the control unit DSE 6020. It also starts and stops the group manually via a pushbutton or remote start-up by contact Image for guidance purposes. CONTACT US FOR DETAILED DATA SHEETS AND OTHER CONTROL PANEL OPTIONS