HVLP Spray Systems Raising Performance to a New Level
New CAPspray Features: Patented noise reduction system makes the CAPspray line the quietest available. Dual filtration is the most advanced on the market. Includes easy-clean filters and filter warning system. Maxum II gun, integrated gun holder, one-quart cup with rotating pick-up tube and flex air hose are included. CS8100 Model No. 0277030 CS9100 Model No. 0277047 CS5100 Model No. 0277032 Unit Specifications Max. Noise Filter Turbine Turbine Unit Level Dual Cup Hose Warning Model Amps PSI Stages Hose Weight (Decibels) Filtration Holder w/unit Light CS5100 9.0 5.0 2 30' 18.0 76.0 X X 15' CS8100 10.5 6.0 3 60' 22.5 71.2 X X 30' X CS9100 12.4 8.5 4 60' 23.5 70.0 X X 30' X PSI is the key factor when judging HVLP sprayers. Simply stated, higher PSI allows you to break up thicker, higher viscosity materials. An HVLP gun requires only 5-20 CFM to atomize virtually any coating. ALL manufacturers turbines provide enough air flow. Make sure they provide the PSI you need for your job.
Better Performance. CAPspray s new line offers the best atomization in the industry. When coupled with the new, versatile and accurate Maxum II gun, the CAPspray System provides 15% improved atomization. Quiet Operation. With CAPspray, more power doesn t mean more noise. CAPspray provides quiet, dependable operation to ensure you get the job done with less hassles and no headaches. Patented noise-reduction system. The CS9100 four-stage turbine is as quiet as competitive two-stage units! Smaller. Tougher. You ll appreciate CAPspray s lightweight design and its heavyweight features! Gun holders on all models so you ll have less to carry. The largest, CS9100 four-stage unit, is lighter than most competitive two-stage turbines. Stands up to the toughest handling with a cast aluminum and drawn-steel housing. Unit handle is centered for balanced load and improved portability. Maximum Filtration. CAPspray s Dual Filtration System is the most advanced on the market. It uses separate filters for atomizing and cooling air. Clogged filter warning light. Two-stage, fine mesh filter on atomizing air chamber provides cleaner, smoother finish. Single-stage cooling air filter optimizes air flow while ensuring clean operation and longer life. Filter warning light lets you know when it's time to clean or replace the filters.
HVLP Accessories CAPspray Portable Cart Model No. 0277063 Cart. Includes 2.5 gallon pressure pot and compressor Model No. 0277077 Cart with CS9100 For increased production, portability and gun maneuverability. Accommodates CS5100, CS8100 or CS9100 units. Compressor filtered for longer life and less downtime. Wide cart for better stability. Handle folds down easily for transport. Comes with 30' material hose. CAPspray CS3000 Two-quart Remote System Model No. 0277045 Allows you to reach small, tight areas quickly and easily. Provides greater capacity and maneuverability. Reduces user fatigue. Accommodates CS5100, CS8100 or CS9100 units. Increases paint supply capacity. Hang from your belt or use with shoulder strap accessory. Standard and Deluxe HVLP Maintenance Kits For basic maintenance needs of HVLP Systems Standard Maintenance Kit includes: Model No. 0279942 #2 Projector Set, #4 Projector Set, gun wrench, 6 check valve seals, needle packing, replacement check valve assembly, cup gasket, and an air plug. Deluxe Maintenance Kit includes: Model No. 0279941 #2 Projector Set, #4 Projector Set, #5 Projector Set, gun wrench, 6 check valve seals, needle packing, 2 check valve assemblies, 2 cup gaskets, cup filter, air-tight lid, and an air plug. Standard HVLP Maintenance Kit Deluxe HVLP Maintenance Kit
CAPspray Maxum II Gun The highest standard in HVLP CAPspray s new Maxum II gun provides the finest atomization in the industry and gives contractors the ability to atomize a wider variety of coatings, work at greater speeds, experience less operator fatigue, and get quality results that meet the demands of any job. Click-in air cap for quick pattern adjustment and no guesswork. Optional air inlets provide non-bleed to bleed conversion for greater versatility. Stainless steel needle and nozzle. Patented dual pivot trigger for reduced pull. Solvent-proof Teflon seals. External packing nut adjustments. Increased internal air passages for greater flow, higher pressure and the ability to handle heavier coatings. 15% Improved Performance Patented stay-cool handle. Multi-position pick-up tube for longer use without refill. Patented bleeder to non-bleeder conversion feature Non-bleed eliminates constant air discharge that can blow dust onto newly painted surfaces. The bleed configuration gives maximum air flow for breaking up highly viscous materials. SoftPull trigger By removing the upper pin as shown above, the gun can be converted to the SoftPull trigger, giving you maximum comfort when spraying light viscosity materials such as stains and sealers.
Pro Set Recommendation Chart Material Percent Minimum Unit Projector Set Projector Set Reduction Recommended Recommended Orifice Size (in.) Stain 0 5100 #2 to #3.031 to.051 Varnish 0 5100 #2 to #3.031 to.051 Sealer 0 5100 #2 to #3.031 to.051 Primer 5-15 5100 #2 to #3.031 to.051 Polyurethane 0 5100 #2 to #3.031 to.051 Nitrocellulose Lacquer Mfg. Rec. 5100 #2 to #3.031 to.051 Water Base Epoxy 5% 9100 #3 to #4.051 to.070 Water Reducible Lacquer 0-10 8100 #3 to #4.051 to.070 Epoxy 10-15 8100 #4 to #5.070 to.086 Interior Alkyd 5-15 5100 #3 to #4.051 to.070 Exterior Oil 5-15 8100 #3 to #4.051 to.070 Quick Dry Enamel 5-15 5100 #3 to #4.051 to.070 Industrial Enamel 5-15 5100 #3 to #4.051 to.070 Interior Finish Latex 10-15 8100 #4 to #5.070 to.086 Metal Latex 5-10 9100 #4 to #5.070 to.086 Contact Cement 0 8100 #4 to #5.070 to.086 Multi-Color Finishes 0 8100 #4 to #5.070 to.086 Note: Because of variations in materials, recommendations in this chart should be used as starting points. You may achieve acceptable results using different unit and projector set combinations. Other HVLP Accessories Projector Sets #2 Pro Set (Fine Finish).........................................0276254 #3 Pro Set (All Purpose).......................................0276227 #4 Pro Set (High Output).......................................0276228 #5 Pro Set (Higher Output)......................................0276229 #6 Pro Set (Highest Output).....................................0276245 HVLP Maxum II Guns Maxum II Non-Bleeder with #3 Pro Set and cup......................0277034 Maxum II Non-Bleeder with #3 Pro Set for pressure feed...............0277057 Maxum II Non-Bleeder with #3 Pro Set and Gravity Cup...............0277055 Maxum II Non-Bleeder with #3 Pro Set, Maxum II Top Feed Cup and Regulator.............................0277075 Maxum II Non-Bleeder with #3 Pro Set and Regulator.................0277076 HVLP Spray Gun Extensions 12 Extension (12" needle included)................................0276102 24 Extension (12" needle included)...............................0276103 Check Valve Kits Replacement Check Valve Assemblies (Package of 3)..................0297051 Check Valve Disks (Package of 10)................................0276257 Cup Gaskets White Cup Gasket for Hot Solvents (Package of 6)....................0297052 Replacement Filters (all models) Air Filter Kit..................................................0279937 2 1 /2 Gallon Pressure Pot Accessories Pressure Pot Liner.............................................0275702 Solvent Resistant Gasket..........................................18206 Cups and Accessories 1-Quart Replacement Cup.......................................0275573 2-Quart Remote Cup with 6" hose.................................0277067 Air-Tight Lid for Paint Cups (retains paint for long periods).............104-0073 Hoses and Fittings Air Hose 2' x 3 /4" Flex Whip Hose.........................................0277901 15' x 3 /4" Flex Air Hose..........................................0275275 30' x 3 /4" Flex Air Hose..........................................0277337 2 Gun Adapter for Air Hose......................................0275286 Quick Disconnect (F)...........................................0275625 External Air Control Valve.......................................0279968 Material Hose 30' x 3 /8" Material Hose.........................................0277348 2 Gun Adapter for Material Hose..................................0275287 Warranty Information On every job, your reputation is on the line. Protect it with the proven reputation of our CAPspray products. We ll stand behind you with the best service and support program in the industry. 30-day satisfaction guarantee. One year of free maintenance. Our Painter Down Program sends replacement parts to the nearest service center within 24 hours. Over 500 authorized service centers are conveniently located throughout the United States. For more information, call 1-800-292-4637 Spray Tech Corporation 1770 Fernbrook Lane, Minneapolis, MN 55447 Form No. SL25684 1999, Spray Tech Corp. All Rights Reserved. Printed in U.S.A. (49920K) For more information, visit our Web site: www.spraytechinc.com