Long-distance type CSM DS_E_4_ Long-distance Capacitive Sensor with djustable Sensitivity CE Marking for DC 3-wire models and C/DC 2-wire models. Noise-resistant models are also available for environments with strong noise. Be sure to read Safety Precautions on page 7. Ordering Information Sensors [Refer to Dimensions on page 8.] Model ppearance distance Output configuration mode Standard Models Unshielded 3 to 2 mm DC 3-wire, NPN 2ME 2M 2ME2 2M C 2-wire 2MY 2M 2MY2 2M Noise-resistant Models 34 dia. 3 to 2 mm DC 3-wire, NPN 2MC 2M 2MC2 2M C/DC 2-wire 2MT 2M 2MT2 2M ccessories (Order Separately) Mounting Brackets Mounting Bracket is provided. [Refer to Dimensions on page 8.] ppearance Model Quantity Remarks Y92E-34 Provided with the product.
Ratings and Specifications Standard Models Item Model 2ME 2ME2 2MY 2MY2 distance * area 2 mm 3 to 2 mm Detectable Conductors and dielectrics Standard sensing Differential travel Response frequency Power supply (operating range) Current consumption Leakage current Control output current Grounded metal plate: mm % max. of sensing sensing distance (when adjusted to 2 mm ±% with standard sensing ) 7 Hz Hz 2 to 24 DC ( to 4 DC), ripple (p-p): % max. to 22 C (9 to 2 C), /6 Hz E Models: m max. at 2 DC, 6 m max. at 24 DC Y Models: m max. at C (/6 Hz) with output turned, 2 m max. at 2 C (/6 Hz) with output turned 2 m max. to 2 m (resistive load) 2 max. ( current: 2 m, Cable length: 2 m) Refer to Engineering Data on page 4. Indicators Detection indicator (red) indicator (red) mode (with sensing approaching) Protection circuits mbient temperature range mbient humidity range Temperature influence oltage influence E/Y Models: E2/Y2 Models: Refer to the timing charts under I/O Circuit Diagrams on page for details. Reverse polarity protection, Surge suppressor Operating/Storage: 2 to 7 C (with no icing or condensation) Operating/Storage: 3% to 9% (with no condensation) Surge suppressor ±% max. of sensing distance at 23 C in the temperature range of to C ±2% max. of sensing distance at 23 C in the temperature range of 2 to 7 C ±2% max. of sensing distance at the rated in rated ±% range ±2% max. of sensing distance at the rated in rated +2%, % range at C, ±2% range at 2 C Insulation resistance MΩ min. (at DC) between current-carrying parts and case Dielectric strength, C, /6 Hz for min between current-carrying parts and case, C, /6 Hz for min between current-carrying parts and case ibration resistance Destruction: to Hz,.-mm double amplitude for 2 hours each in X, Y, and Z directions Shock resistance Destruction: m/s 2 times each in X, Y, and Z directions Degree of protection IEC 629 IP66 Connection method Pre-wired Models (Standard cable length: 2 m) Weight (packed state) pprox. 2 g Case Materials surface Heat-resistant BS ccessories Mounting Bracket, M4 screws, Instruction manual * The set distances are sensing distances applicable to standard sensing s. Refer to Engineering Data on page 4 for other materials. 2
Noise-resistant Models Item Model 2MC 2MC2 2MT 2MT2 distance 2 mm * area Detectable Standard sensing Differential travel Response frequency *2 Power supply (operating range) Current consumption 3 to 2 mm Conductors and dielectrics Grounded metal plate: mm % max. of sensing distance (when adjusted to 2 mm ±% with standard sensing ) 4 Hz C power: 2 Hz, DC power: 4 Hz 2 to 24 DC ( to 36 DC), ripple (p-p): % max. 24 to 24 C (2 to 2 C), /6 Hz; 24 to 24 DC (2 to 2 DC) 3 m max. at 24 DC --- Leakage current --- Control output Indicators current mode (with sensing approaching) 2 m max. to 2 m (resistive load) 2. max. ( current: 2 m, Cable length: 2 m) indicator (yellow) C/T Models: C2/T2 Models:. m max. at 24 DC,.7 m max. at C (/6 Hz), 2. m max. at 2 C (/6 Hz) Refer to Engineering Data on page 4. C power: max., DC power: 8 max. Refer to Engineering Data on page 4. Refer to the timing charts under I/O Circuit Diagrams on page for details. Protection circuits Reverse polarity protection, short-circuit protection --- mbient temperature range Operating/Storage: 2 to 7 C (with no icing or condensation) mbient humidity range Operating/Storage: 3% to 9% (with no condensation) Temperature influence ±% max. of sensing distance at 23 C in the temperature range of to C ±2% max. of sensing distance at 23 C in the temperature range of 2 to 7 C oltage influence ±2% max. of sensing distance at the rated in rated ±% range Insulation resistance MΩ min. (at DC) between current-carrying parts and case Dielectric strength, C, /6 Hz for min between current-carrying parts and case, C, /6 Hz for min between current-carrying parts and case ibration resistance Destruction: to Hz,.-mm double amplitude for 2 hours each in X, Y, and Z directions Shock resistance Destruction: m/s 2 times each in X, Y, and Z directions Degree of protection IEC 629 IP6 Connection method *3 Pre-wired Models (Standard cable length: 2 m) Weight (packed state) pprox. 24 g Case Materials surface PBT ccessories Mounting Bracket, M4 screws, Instruction manual *. The set distances are sensing distances applicable to standard sensing s. Refer to Engineering Data on page 4 for other materials. *2. The response frequency is an average value. *3. Only 2-m cables are available. Use a cable with a conductor cross section of. mm 2 or greater to extend the cable. 3
Engineering Data (Typical) Common Mode Continuous Noise Distance Change by Object 2M 2M@@ 2M@@ Noise (p-p) 6 4 2 2M Distance X (mm) 2 2 Distance X (mm) 2 2 8 OMR product (2M) 6 4 2 Frequency (khz) Standard sensing ( t) ml milk (pure water) Flour Sugar Salt Phenolic resin ( ) Neoprene rubber ( t) Output oltage Leakage Current 2MY at C 2MY at 2 C 2MY () 9 8 7 6 4 3 2 oltage output C 2 current (m) () 2 oltage output 2MT at C 2MT at 2 C 2MT Glass (2 t3) Lavan plate (6 2 t) Resin pellet (Duracon) 2 C 2 current (m) Leakage current (m) 3. 2. 2.... Standard sensing ( t) 8 ml milk (pure water) Flour Sugar Salt Phenolic resin ( ) Neoprene rubber (2 t3) Glass (2 t3) Lavan plate (6 2 t) Resin pellet (Duracon) 2 4 6 8 2 22 24 26 Power supply () () 9 8 7 output () 2 output Leakage current (m) 2. 2.. C power 6 4 3 2 oltage C 2 2 current (m) oltage 2 C 2 2 current (m).. 2 DC power 2 2 Power supply () 4
rea (Grounded Metal Plate) Object Size vs. area Distance 2M@@ 2M@@ 2M@@ Distance X (mm) 3 2 2 Standard sensing X head Sensitivity adjustment 2 mm 2 mm mm Distance X (mm) 3 2 2 X Square sensing Grounded metal plate Ungrounded metal plate ( t) distance X (mm) 3 3 2 2 Standard sensing X head Y mm mm Phenolic resin plate (6 t) head 2 2 2 2 Distance Y (mm) 2 3 4 6 7 8 9 Side length of sensing (mm) 2 head 2 Distance Y (mm) I/O Circuit Diagrams DC 3-Wire Models mode Model Timing chart Output circuit 2ME 2ME2 (between brown and black leads) Output (between black and blue leads) Detection indicator (red) (between brown and black leads) Output (between black and blue leads) Detection indicator (red) High Low High Low Proximity Sensor main circuit 4.4 kω Brown Black * Output *2 Blue *. current: 2 m max. *2. When a transistor is connected. Tr + 2MC 2MC2 (between brown and black leads) Indicator (yellow) (between brown and black leads) Indicator (yellow) Proximity Sensor main circuit Brown Black Blue * current: 2 m max. * 2 to 24 DC
C 2-Wire Models mode Model Timing chart Output circuit 2MY Brown indicator (red) Proximity Sensor main circuit Blue 2MY2 indicator (red) C/DC 2-Wire Models mode Model Timing chart Output circuit 2MT Brown* 24 to 24 DC 24 to 24 C indicator (yellow) Proximity Sensor main circuit Blue 2MT2 indicator (yellow) * current: 2 m max. 6
Safety Precautions Refer to Warranty and Limitations of Liability. This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. Do not use this product under ambient conditions that exceed the ratings. Design Influence of Surrounding Metal When mounting a Proximity Sensor, be sure to provide a distance of 8 mm min. from surrounding metal s to prevent the Sensor from being affected by metal s other than the sensing. When mounting the Sensor with the L-shaped Mounting Bracket, be sure to provide a distance of 2 mm min. between the face of the sensing head and the Mounting Bracket. Be sure to ground. WRNING Precautions for Correct Use 2 mm min. 8 mm min. surface Metal Surrounding conductive s 8 mm min. 8 mm min. 8 mm min. Surrounding conductive s Mutual Interference When installing Sensors face-to-face or side-by-side, ensure that the minimum distances given in the following table are maintained. Effects of a High-frequency Electromagnetic Field The may malfunction if there is an ultrasonic washer, highfrequency generator, transceiver, portable telephone or inverter nearby. For major measures, refer to Noise of Warranty and Limitations of Liability for Photoelectric Sensors. Objects Object Material The can detect almost any type of. The sensing distance of the, however, will vary with the electrical characteristics of the, such as the conductance and inductance of the, and the water content and capacity of the. The maximum sensing distance of the will be obtained if the is made of grounded metal. Indirect Detection To detect s in metal containers, each metal container must have a nonmetallic window. Power Conditions is enabled within 2 ms for the 2M@@. Design the system so that the power for the Sensor is turned before the power for the load. Miscellaneous Organic Solvents The Sensor has a case made of heat-resistant BS resin or PBT resin. Be sure that the case is free from organic solvents or solutions containing organic solvents. Face-to-face Mounting Parallel Mounting B Mutual Interference (Unit: mm) Dimension B Model 2M@@ 2M@@ 7
Dimensions Sensors 2M@@ (Unit: mm) Tolerance class IT6 applies to dimensions in this data sheet unless otherwise specified. 82 7 Cap 3 Screw hole for sensitivity adjustment - 34 dia. + 2 Cable clamp E Models: 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section:. mm 2, Insulator diameter:.9 mm), Standard length: 2 m Y Models: 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section:. mm 2, Insulator diameter:.9 mm), Standard length: 2 m Indicator* * E Models: Detection indicator (red) Y Models: indicator (red) 2M@@ 8 8 indicator (yellow) Sensitivity adjuster 34 dia. 9 C Models:.-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section:. mm 2, Insulator diameter:. mm), Standard length: 2 m T Models:.-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section:. mm 2, Insulator diameter:. mm), Standard length: 2 m ccessories (Order Separately) Mounting Bracket (ccessory) Y92E-34.2 4 R2.6 43 6.3 Two elliptic holes for bracket mounting 2 23. 3 42 4.4 Two, M4 Sensor clamping screws Sensor mounting hole With Mounting Bracket ttached E2K Material: Polyacetal Two,.-dia. mounting holes* Note: Provided with the product. 3 4 4 7.6 * The holes are not drilled completely through. Drill through the holes before using them. 3 3 6 8
Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMR representative if you have any questions or comments. Warranty and Limitations of Liability WRRNTY OMR's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMR. OMR MKES WRRNTY OR REPRESENTTI, EXPRESS OR IMPLIED, REGRDING N-INFRINGEMENT, MERCHNTBILITY, OR FITNESS FOR PRTICULR PURPOSE OF THE PRODUCTS. NY BUYER OR USER CKWLEDGES THT THE BUYER OR USER LE HS DETERMINED THT THE PRODUCTS WILL SUITBLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMR DISCLIMS LL OTHER WRRNTIES, EXPRESS OR IMPLIED. LIMITTIS OF LIBILITY OMR SHLL T BE RESPSIBLE FOR SPECIL, INDIRECT, OR CSEQUENTIL DMGES, LOSS OF PROFITS OR COMMERCIL LOSS IN NY WY CNECTED WITH THE PRODUCTS, WHETHER SUCH CLIM IS BSED CTRCT, WRRNTY, NEGLIGEE, OR STRICT LIBILITY. In no event shall the responsibility of OMR for any act exceed the individual price of the product on which liability is asserted. IN EENT SHLL OMR BE RESPSIBLE FOR WRRNTY, REPIR, OR OTHER CLIMS REGRDING THE PRODUCTS UNLESS OMR'S NLYSIS CFIRMS THT THE PRODUCTS WERE PROPERLY HNDLED, STORED, INSTLLED, ND MINTINED ND T SUBJECT TO CTMINTI, BUSE, MISUSE, OR INPPROPRITE MODIFICTI OR REPIR. pplication Considerations SUITBILITY FOR USE OMR shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. t the customer's request, OMR will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEER USE THE PRODUCTS FOR N PPLICTI ILING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THT THE SYSTEM S WHOLE HS BEEN DESIGNED TO DDRESS THE RISKS, ND THT THE OMR PRODUCTS RE PROPERLY RTED ND INSTLLED FOR THE INTENDED USE WITHIN THE OERLL EQUIPMENT OR SYSTEM. PROGRMMBLE PRODUCTS OMR shall not be responsible for the user's programming of a programmable product, or any consequence thereof. Disclaimers CHNGE IN SPECIFICTIS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMR representative at any time to confirm actual specifications of purchased products. DIMENSIS ND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. PERFORME DT Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMR s test conditions, and the users must correlate it to actual application requirements. ctual performance is subject to the OMR Warranty and Limitations of Liability. ERRORS ND OMISSIS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. OMR Corporation Industrial utomation Company http://www.ia.omron.com/ 2.8 In the interest of product improvement, specifications are subject to change without notice. (c)copyright OMR Corporation 2 ll Right Reserved.