[1] Submitted by Ana White [2] on Wed, 2013-01-23 13:59 [1] Additional Photos [3] [4] Page 1 of 19
[5] [6] Hello DIY Friends! Today we have such a very special post for you. My dear friend Brooke from Killer b. Designs [7] is building a new house, and they are DIYing much of it themselves. Brooke is already an amazing builder, and when it came time to tackle the kitchen, she decided to DIY the kitchen cabinets! Page 2 of 19
Yep, It's all DIY! Page 3 of 19
Right down to the bright red island custom fit for a microwave! Page 4 of 19
And the paper towel holder built right into the kitchen design! Amazed already? There are tons tons tons more pictures and details on Brooke's kitchen, but it would be unfair to you to not go visit Brooke and read from her all about her DIY kitchen. [7] Page 5 of 19
From Brooke: Handbuilt Vintage Country Kitchen [7] Customizing 21" Drawer and Paper Towel Cabinets [8] Customizing 24" Open Cabinets [9] Customizing 30" Bases [10] Tips and Tricks [11] Must reads if you are even considering redoing your kitchen or any cabinetry in your home! Why not save hundreds (if not thousands) of dollars, build your cabinets with PureBond Formaldehyde [12]-free 3/4" thick plywood, and get EXACTLY what you want? Thank you so much Brooke for sharing your DIY kitchen with us today! And OF COURSE we've got you covered with the plans as well if you want to build your own kitchen cabinets. In today's plan, I'll show you how to make a base cabinet carcass. You can customize the width to any width you like, but I recommend staying under 36" to avoid having saggy shelves or having to reinforce the countertop for support. We'll get into specific drawer posts and door options later on. Read on! NOTE: I do work with (and love) the folks at PureBond Plywood [12], but this here post is not sponsored by them. Summary: How to build your own kitchen cabinet base plans from ana-white.com CategoriesProject Type: Kitchen Cabinets [13] Room: kitchen [14] Skill Level: Intermediate [15] Page 6 of 19
Style: farmhouse [16] Kitchen Plans: Base Cabinet [17] Dimensions: Can be customized to any width - standard height is 34 1/2" Dimensions: 3/4" cabinet plywood (PureBond shown) ripped into 22 1/2" widths 1x4 boards (can be pine) for bottom supports and top supports 1x2 boards for face frames in wood species matching cabinet plywood 1/4" plywood for backs if desired and also can be used to finish off exposed kitchen cabinet ends and ripped into strips to finish off toekick after cabinet installation 1 1/4" pocket hole screws Tools: Page 7 of 19
[18] [19] Page 8 of 19
[20] [21] Cut List: [22] (click to expand [22]) General Instructions: Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck! Page 9 of 19
Step 1 [23] Rip plywood into 22 1/2 wide strips. Save the leftover scrap piece, you can use it as a support board in step 3, or use it to make corner bracing. For each base cabinet, you will need two sides. Cross cut the 22 1/2 strips down to 34 1/2. Notch out toekick with jigsaw. NOTE: If you wish to attach face frames with pocket holes, drill 3/4 pocket holes on inside front edges of the sides. Step 2 Page 10 of 19
[24] Cut shelves from 22 1/2 wide strips. You will need at minimum a bottom shelf. You can cut additional shelves as well. For all fixed shelves, drill 3/4 pocket holes on 22 1/2 long sides and attach to sides with 1 1/4 pocket hole screws. Note that your carcass is 1/2 less in overall width than your desired finished cabinet dimensions. NOTE: for face frames attached with pocket holes, also drill 3/4 PHs facing forward for attaching face frames in later steps on underside of bottom shelf. Step 3 Page 11 of 19
[25] You can use the scrap plywood strips here. This just helps you square up your cabinet and gives you something to attach countertop plywood to. Place 3/4 pocket holes and 1 1/4 pocket hole screws to top - they will get covered in later steps. NOTE: For attaching face frame with pocket holes, also drill 3/4 pocket holes facing forward on top of front support. Step 4 Page 12 of 19
[26] You can again use scrap plywood here. Also attach to top support. You will use this board to attach base cabinet to wall, and it also helps square up the back of the cabinet. A back can be attached, but it may be easier to wait to attach the backs until after you install drawers or shelves. Step 5 Page 13 of 19
[27] Footer is 1x4 board. You can use any material here as the finished toe kick will be installed over top when cabinet installation is complete. For wide width cabinets or cabinets with expected heavy loads, a back 1x4 is also recommended. Step 6 Page 14 of 19
[28] Build face frames first with pocket holes and glue. If you have trouble with wood splitting, try setting pocket holes for 1/2 stock and using 1 pocket hole screws. Note that your face frames are 1/2 wider than the carcass, or the desired with of your cabinet. This gives you some wiggle room when you install the cabinets to get your face frames to line up perfectly level. For end cabinets, you can also finish off ends with 1/4 plywood if desired (ie if you were using Melamine for carcasses and Maple for face frames and doors, you would finish off ends and toe kick with maple hardwood plywood to hide all Melamine) Page 15 of 19
I love how Brooke [7]finished off her kitchen island ends with beadboard. Step 7 Page 16 of 19
[29] To give you an idea of the placement of face frame boards for drawers/doors here is the diagram I sent Brooke. Step 8 [30] And then here is the diagram I sent Brooke for the door sizes. You'll want a finished reveal gap of 1/2" between everything for full overaly doors/drawers, so between cabinets, that's 1/4" per cabinet, but between doors/drawers on the same cabinet it's 1/2" gap. Page 17 of 19
I'll get into this more when we do plans for drawers and doors and accessories and of course wall cabinets. Finishing InstructionsPreparation Instructions: Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed. Source URL: http://www.ana-white.com/2013/01/plans/face-frame-ba se-kitchen-cabinet-carcass Links [1] http://www.ana-white.com/2013/01/plans/face-frame-base-kitchen-c abinet-carcass [2] http://www.ana-white.com/users/ana-white [3] http://www.ana-white.com/sites/default/files/3154820821_13589711 41.jpg [4] http://www.ana-white.com/sites/default/files/3154820818_13589711 41.jpg [5] http://www.ana-white.com/sites/default/files/3154820822_13589711 41.jpg [6] http://www.ana-white.com/sites/default/files/3154820823_13589711 41.jpg [7] http://www.killerbdesigns.com/a-handbuilt-vintage-country-kitchen/ [8] http://www.killerbdesigns.com/21-cabinets-pinterest-style/ [9] http://www.killerbdesigns.com/24-open-cabinets/ [10] http://www.killerbdesigns.com/customizing-my-30-base-cabinets-a nd-28-upper-cabinets/ [11] http://www.killerbdesigns.com/tips-and-tricks-for-building-your-own -cabinets/ [12] http://www.purebondplywood.com [13] http://www.ana-white.com/category/plans/project-type/kitchen-cabinets [14] http://www.ana-white.com/category/plans/room/kitchen [15] http://www.ana-white.com/category/plans/skill-level/intermediate Page 18 of 19
[16] http://www.ana-white.com/category/plans/style/farmhouse [17] http://www.ana-white.com/category/plans/kitchen-plans/base-cabinet [18] http://www.kregtool.com/files/anawhite/anawhite.asp [19] https://www.ryobitools.com/power-tools/products/details/92 [20] https://www.ryobitools.com/power-tools/products/details/552 [21] https://www.ryobitools.com/power-tools/products/details/187 [22] https://lh5.googleusercontent.com/-fmrlp282n3i/uqboyy7pkji/aaa AAAAANVk/6JE12k19D3c/s582/base-carcass-cut-list.jpg [23] http://www.ana-white.com/sites/default/files/3154820825_1358971 141.jpg [24] http://www.ana-white.com/sites/default/files/3154820827_1358971 141.jpg [25] http://www.ana-white.com/sites/default/files/3154820826_1358971 141.jpg [26] http://www.ana-white.com/sites/default/files/3154820828_1358971 141.jpg [27] http://www.ana-white.com/sites/default/files/3154820829_1358971 141.jpg [28] http://www.ana-white.com/sites/default/files/3154820830_1358971 141.jpg [29] http://www.ana-white.com/sites/default/files/3154820831_1358971 141.jpg [30] http://www.ana-white.com/sites/default/files/3154820832_1358971 141.jpg Page 19 of 19