DXL Group QUALITY ASSURANCE MANUAL

DXL Group QUALITY ASSURANCE MANUAL July 2014

DXL Group QUALITY ASSURANCE MANUAL TABLE OF CONTENTS INTRODUCTION ------------------------------------------------------------------------------------------------------------- 3 REGULATORY COMPLIANCE NOTICE ---------------------------------------------------------------------------------- 4 DXL GROUP POLICY STATEMENT --------------------------------------------------------------------------------------- 5 TESTING PROCEDURES ---------------------------------------------------------------------------------------------------- 6 I. DXL GROUP RESPONSIBILITY ----------------------------------------------------------------------------------------------- 6 II. VENDOR RESPONSIBILITY --------------------------------------------------------------------------------------------------- 6 III. BVCPS RESPONSIBILITY ------------------------------------------------------------------------------------------------------ 8 SAMPLE SUBMISSION GUIDELINE -------------------------------------------------------------------------------------- 9 VENDOR CONFIRMATION FORM ------------------------------------------------------------------------------------- 10 PROTOCOL INDEX -------------------------------------------------------------------------------------------------------- 11 Page 2 of 61 Revised Date

INTRODUCTION This DXL Group Quality Assurance Manual provides the administrative procedures and quality assurance requirements under the testing program. The Consumer Products Services Division of Bureau Veritas (BVCPS) is the approved laboratory under this program and will perform testing on all items as requested by DXL Group and its suppliers as outlined in this manual. DXL Group performance standards are based on past experience. The Performance Standards are used as a guideline for the evaluation of DXL Group acceptability. Most test methods and test procedures are originated from: ASTM (American Society of Testing and Materials) AATCC (American Association of Textile Chemists and Colorists) CPSC (Consumer Product Safety Commission) FTC (Federal Trade Commission) Page 3 of 61 July 2014

REGULATORY COMPLIANCE NOTICE In addition, all products or product components sold to DXL Group, must meet the provisions of all U.S. Federal, State and Local Regulations. These include, but are not limited to: Code of Federal Regulations - Standard for the Flammability of Clothing Textiles FTC Trade Regulation Rule for Care Labeling of Textile Wearing Apparel FTC Rules and Regulations under the Textile Fiber Products Identification Act FTC Rules and Regulations under the Wool Products Labeling Act State Regulations for the Feather and Down Products Industry FTC Rules and Regulations under the Fur Products Labeling Act CPSC Rules and Regulations for Child Safety State & Federal Regulations for Restricted Substances Fabric Mills and Trim Suppliers must provide a continuing guarantee of compliance or test results assuring that requirements of all U.S. Federal, State and Local Regulations are met. Page 4 of 61 July 2014

DXL Group POLICY STATEMENT 1. DXL Group is committed to delivering quality merchandise to the DXL Group customer. 2. This program is based on the mandate that all merchandise purchased by DXL Group must be tested to meet all applicable laws and regulatory requirements, in addition to ensuring compliance with DXL Group customer satisfaction and acceptability. 3. DXL Group accepts test reports from BVCPS or a BVCPS affiliate. Any exceptions must be agreed to in advance with DXL Group. 4. This testing or any subsequent result does not limit DXL Group rights or diminish or remove vendor or manufacturer's responsibilities and obligations under the Purchase Order Terms and Conditions. Page 5 of 61 July 2014

TESTING PROCEDURES I. DXL GROUP RESPONSIBILITY Provide the vendor with a copy of the DXL Group Vendor Guide, Chapter 5 and protocols. When a product fails testing, DXL Group will determine the disposition as to retest or cancellation of the order, etc. II. VENDOR RESPONSIBILITY See Chapter 5-DXLG QA program for vendor testing policy. As a vendor to DXL Group, you are fully responsible for all fabric and garment testing of production merchandise. You must guarantee that fabric and garments pass all tests before production and shipment. The best timing for fabric testing is upon the initial run of production. The best timing for garment testing is upon receipt of our order with the correct samples. It is the vendor s responsibility to ensure that all necessary tests are done to meet DXL Group requirements. All initial or first tests will be paid by the DXL Group. All retest will be paid by the Vendor. Sample submission to BVCPS : Fabric Testing: For initial bulk fabric testing, a minimum of two (2) square yards must be submitted for full testing in one (1) colorway along with a minimum of one (1) square yard fabric in each additional colorway. Fabric must be identical in every aspect to bulk production piece goods including color and prints. Pre-Production Garment Testing: Send four (4) garments in each style in the largest size available for complete garment testing. Pre-Production Garments must be made on production machinery and must represent bulk production. If additional garment / fabric is required, BVCPS will immediately contact the vendor. A completed DXL Group Test Request Form should be submitted with garment / fabric. BVCPS will not accept a sample if the form is incomplete. The Vendor may obtain Test Request Forms directly from BVCPS (See Enclosed Test Request Form). Garments must include all bulk trim, accessories and embellishments. Findings and Functional / Decorative Trim Number of Samples Required Zippers 6 Zippers Buttons and Snaps 10 Samples (To be tested on garment stage) Elastic 3 Samples Applied Trim: Lace, Bows, Ribbon, Patches, Etc. 8 Samples, 1 Yard OR 4 Garments Screenprint, Embroidery / Appliqué 5 Samples OR 4 Garments VISUALLY UNSATISFACTORY SAMPLES (stains, tears, and missing pieces) WILL NOT BE ACCEPTED FOR TESTING! Page 6 of 61 July 2014

II. VENDOR RESPONSIBILITY (Continued) Samples Required for Testing Garment Retests: All retests are the vendor s responsibility. Note: On product re-tests, the previous test report number must be referenced on the Test Request Form. If a previous report number is not referenced, the full fabric and garment tests may be performed on the submission. All retested fees are vendor s responsibility. Ongoing Programs: Products that are purchased on an ongoing basis must be tested in accordance with the appropriate packages at least once every 6 months, and/or when changes have been made in production. Page 7 of 61 July 2014

III. BVCPS RESPONSIBILITY When the Test Request Form is incomplete, the laboratory will notify the originating vendor. Until proper information is received, testing will be delayed. Complete testing and evaluate the test results (See DXL Group Standard Test Package). Rate the product by: o Pass The product provides good overall consumer serviceability and requires no improvement. o Fail The product has deficiencies of such severity that the customer dissatisfaction will likely result and / or noncompliance or regulatory requirements. The product cannot be sold until improvements are made Reports will be emailed to DXL Group and submitter as well as posted on BVOS. Page 8 of 61 July 2014

SAMPLE SUBMISSION GUIDELINE Sample Preparation Guidelines: Collect production quality sample Each sample must fulfill the minimum sample size requirement Fill out the Test Request Form completely Send Test Application to Testing Lab Laboratory Test Turnaround Time: Regular: 5 working days after receipt of sample Express: Within 3 working days after receipt of sample at surcharge of 40% Nest Business Day: Next working day are available for some tests at surcharge of 100% Some test standards require specified testing period, default service turnaround time may not be applicable, no express and emergency services provided. Testing Working Day Calculation: Sample arrived laboratory Sample log-in Service level available From 9:00 am to 11:00 am Same day morning Emergency service Express service Regular service From 11:00 am to 15:00 pm Same day afternoon Regular service After 15:00 pm Next working day Emergency service Express service Regular service Test Sample Receipt & Hold Memo Test Sample Receipt provides information of test selected and expected report available date for regarding test submission. Hold Memo indicates testing halt when encountering situation of insufficient / inadequate information or samples. Report Distribution To: Applicant (Test Submitter) Cc: Per Test Request From Test report copy will be sent to Client by email when completed. Third Party Billing Official confirmation from Invoice recipient is required Page 9 of 61 July 2014

VENDOR CONFIRMATION FORM I acknowledge receipt of DXL Group Quality Assurance Manual. I have read and understand the policies and procedures set forth and agree to comply with them. Company Name (Type or Print) Company Officer s Signature (Type or Print Name Signed Above) Title Date Page 10 of 61 July 2014

Protocol Index Protocol Name Page 100F Woven Fabric (Shirts & Pants) 12 100G Woven Garment (Shirts & Pants) 14 101F Woven Denim Fabric 15 101G Denim Garment 17 102F Woven Twill Fabric 18 102G Twill Garment 20 200F Knit Fabric 21 200G Knit Garment 23 201F Loungewear / Underwear / Terry Robe / Sleepwear Fabric 24 201G Loungewear / Underwear / Terry Robe / Sleepwear Garment 26 202F Swim Fabric 27 202G Swimwear 29 300G Sweaters 30 400F Leather & Suede Hides 32 400G Leather & Suede Garments 33 500F Lining Fabric (Applies for all Textile Items) 34 600G Textile Hats & Caps 36 601G Socks & Hosiery 38 700 F Outerwear Fabric (Shell Only) 40 700G Outerwear Garment (With or Without Lining) 42 701F Sports Coats / Jackets, Suits Fabric (Shell Only) 43 701G Sports Coats / Jackets, Suits (With or Without Lining) 45 EU Market Requirements 46 800 Components 47 Buttons, Shank Buttons, Snaps, Zippers, Other Hardware 801 Elastic 49 803 Belts 50 804 Suspenders 52 802 Special Claims 55 Zipper Requirements 59 Page 11 of 61 July 2014

100F Woven Fabric (Shirts & Pants) Page 1 of 2 Analytical ph value AATCC 81 6-8 Flammability Flammability Of Clothing Textiles 16 CFR 1610 Class 1 (if not exempt) All Colors Physical Characteristics *Fiber Analysis AATCC 20/20A 0% Single Fiber ± 3% Blends Fabric Weight ASTM D3776 ± 5% from claim Fabric Count ASTM D3775 ± 5% from claim Special Fabric Type As claimed Yarn Size (If Claimed) (If Claimed) ASTM D1059 ± 5% from claim Defects Report all defects Performance 100% Cotton: -4% Dimensional Stability-Home AATCC 135 All others: -3% Laundering (3 washes) Growth: +1% Dimensional Stability-Drycleaning (1 cycle) AATCC 158 Note: Mandatory for dress pants Shrinkage: -2% No growth No distortion, defects, excessive puckering Pilling: Class 4.0 No distortion defects General Appearance after care (3HL or 1 DC) CPSD-SL-31055-MTHD Appearance after Ironing Hand Iron Skew/Torque AATCC 179 Method 1, Option 1 5% or ½ maximum Tensile Strength ASTM D5034 < 6.0 oz/yd 2 : 30 lbs min. 6.0 oz/yd 2 : 40 lbs min. < 6.0 oz/yd 2 : 2.5 lbs min. Tear Strength ASTM D1424 6.0-7.9 oz/yd 2 : 3.0 lbs min. 8.0 oz/yd 2 : 4.0 lbs min. Seam Slippage ASTM D1683 20 lbs min @ ¼ Stretch & Recovery ASTM D3107 5% spandex in stretch direction only Stretch: 15% min. Growth: 5% max. Page 12 of 61 July 2014

100F Woven Fabric (Shirts & Pants) Page 2 of 2 Colorfastness CF to Home Laundering AATCC 135 CF to Commercial Dry-cleaning AATCC 132 CF to Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Non-Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 CF to Light AATCC 16, Option 3 Provide ratings after 10 & 20 AFU Pass/Fail based on 20 AFU rating only Class 4.0 @ 20 AFU CF to Water AATCC 107 Color block / Contrast trims only CF to Perspiration AATCC 15 *Phenolic Yellowing ISO 105-X18 White, Ivory if 50% coverage Class 3.5 Note: Please refer to special claims protocol as applicable. Page 13 of 61 July 2014

Labeling Textile Fiber Products Identification Act Care Labeling Rule Wool Products Labeling Act Analytical *Lead in surface coating (If Requested) 100G Woven Garment (Shirts & Pants) Page 1 of 1 CPSC-CH-E1003-09.1 / AOAC 974.02 (mod.) Fiber Content Label RN# or WPL # Country of Origin Care Label Size Physical Characteristics Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) Dimensional Stability-Drycleaning (1 cycle) General Appearance after care (3HL or 1 DC) AATCC 150 AATCC 158 CPSD-SL-31055-MTHD Shall not exceed 90 ppm (0.009% by weight) Seam Skew/Torque AATCC / ASTM TS-004 5% or ½ maximum Seam Strength ASTM D1683 < 6.0 oz/yd 2 : 20 lbs min. 6.0 oz/yd 2 : 25 lbs min. Seam Slippage** ASTM D1683 20 lbs min @ ¼ Component Attachment Strength Refer to protocol 800 Pocket Attachment Strength ASTM D1683 mod 15 lbs min. Note: 1. Any components not previously tested are required to test to appropriate standard 2. Please refer to special claims protocol as applicable. 100% Cotton: -4% All others: -3% Growth: +1% Note: Mandatory for dress pants Shrinkage: -2% No growth No distortion, defects, damaged components, excessive puckering Pilling: Class 4.0 **Seam Slippage: test the following seams: Tops: Side, Shoulder, Yoke, Armhole, Sleeve, Collar & Pocket Bottoms: Side, Inseam, Back Rise, Crotch, Zipper stress area, all pockets Page 14 of 61 July 2014

101F Woven Denim Fabric Page 1 of 2 Analytical ph value AATCC 81 6-8 Flammability Flammability Of Clothing Textiles 16 CFR 1610 Class 1 (if not exempt) All Colors Physical Characteristics *Fiber Analysis AATCC 20/20A 0% Single Fiber ± 3% Blends Fabric Weight ASTM D3776 ± 5% from claim Fabric Count ASTM D3775 ± 5% from claim Special Fabric Type As claimed Yarn Size (If Claimed) ASTM D1059 ± 5% from claim Defects Report all defects Performance Fabric Wash: -2.5% Dimensional Stability-Home AATCC 135 Rigid: -4% Laundering (3 washes) Growth: +1% Dimensional Stability-Drycleaning (1 cycle) AATCC 158 Shrinkage: -2% No growth General Appearance after care (3HL or 1 DC) CPSD-SL-31055-MTHD No distortion, defects, excessive puckering Pilling: Class 4.0 Appearance after Ironing Hand Iron No distortion defects Skew/Torque AATCC 179 Method 1, Option 1 5% or ½ maximum Tensile Strength Tear Strength ASTM D5034 (Warp x Weft) ASTM D1424 (Warp x Weft) 8-10 oz/yd 2 : 55 x 35 min 10.1-12.0 oz/yd 2 : 65 x 40 min >12.0 oz/yd 2 : 85 x 70 min 8-10 oz/yd 2 : 4.0 x 3.0 min 10.1-12.0 oz/yd 2 : 4.0 x 3.5 min >12.0 oz/yd 2 : 6.5 x 4.0 min Seam Slippage ASTM D1683 20 lbs min @ ¼ Stretch & Recovery ASTM D3107 5% spandex in stretch direction only Stretch: 15% min. Growth: 5% max. Recovery (30 sec/30 min): 90% min Abrasion Resistance ASTM D3886 Stretch Denim: 100 cycles min Unwashed: 500 cycles min Washed: 200 cycles min Page 15 of 61 July 2014

101F Woven Denim Fabric Page 2 of 2 Colorfastness CF to Home Laundering AATCC 135 CF to Commercial Dry-cleaning AATCC 132 CF to Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Non-Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 CF to Light AATCC 16, Option 3 Provide ratings after 10 & 20 AFU Pass/Fail based on 20 AFU rating only Class 4.0 @ 20 AFU CF to Water AATCC 107 Color block / Contrast trims only CF to Ozone AATCC 109 Class 3.5 1 cycle CF to Burnt Gas Fumes AATCC 23 Class 3.5 1 cycle *Phenolic Yellowing ISO 105-X18 Solid White or Ivory Class 3.5 Note: Please refer to special claims protocol as applicable. Page 16 of 61 July 2014

Labeling Textile Fiber Products Identification Act Care Labeling Rule Wool Products Labeling Act 101G Denim Garment Page 1 of 1 Fiber Content Label RN# or WPL # Country of Origin Care Label Size Analytical *Lead in surface coating (If CPSC-CH-E1003-09.1 / Requested) AOAC 974.02 (mod.) Shall not exceed 90 ppm (0.009% by weight) ph value AATCC 81 6-8 Physical Characteristics Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) Dimensional Stability-Drycleaning (1 cycle) General Appearance after care (3HL or 1 DC) AATCC 150 AATCC 158 CPSD-SL-31055-MTHD Seam Skew/Torque AATCC TS-004 5% or ½ maximum Seam Strength ASTM D1683 8-10 oz/yd 2 : 35 min 10.1-12.0 oz/yd 2 : 40 min >12.0 oz/yd 2 : 50 min Seam Slippage** ASTM D1683 20 lbs min @ ¼ Component Attachment Strength Refer to protocol 800 Pocket Attachment Strength ASTM D1683 MOD 20 lbs min. Colorfastness CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 Dark Indigo / Black: Dry Class 4.0 Wet Class 2.0 Fabric Wash: -2.5% Rigid: -4% Growth: +1% Shrinkage: -2% No growth No distortion, defects, damaged components, excessive puckering Pilling: Class 4.0 Note: 1. Any components not previously tested are required to test to appropriate standard 2. Please refer to special claims protocol as applicable. **Seam Slippage: test the following seams: Tops: Side, Shoulder, Yoke, Armhole, Sleeve, Collar & Pocket Bottoms: Side, Inseam, Back Rise, Crotch, Zipper stress area, all pockets Page 17 of 61 July 2014

102F Woven Twill Fabric Page 1 of 2 Analytical ph value AATCC 81 6-8 Flammability Flammability Of Clothing Textiles 16 CFR 1610 Class 1 (if not exempt) All Colors Physical Characteristics *Fiber Analysis AATCC 20/20A 0% Single Fiber ± 3% Blends Fabric Weight ASTM D3776 ± 5% from claim Fabric Count ASTM D3775 ± 5% from claim Special Fabric Type As claimed Yarn Size (If Claimed) ASTM D1059 ± 5% from claim Defects Report all defects Performance 100% Cotton: -4% Dimensional Stability-Home AATCC 135 All others: -3% Laundering (3 washes) Growth: +1% Dimensional Stability-Drycleaning (1 cycle) AATCC 158 Shrinkage: -2% No growth General Appearance after care (3HL or 1 DC) CPSD-SL-31055-MTHD No distortion, defects, excessive puckering Pilling: Class 4.0 Appearance after Ironing Hand Iron No distortion defects Skew/Torque AATCC 179 Method 1, Option 1 5% or ½ maximum Tensile Strength Tear Strength ASTM D5034 (Warp x Weft) ASTM D1424 (Warp x Weft) <6.0 oz/yd 2 : 30lb min 6.0-7.9 oz/yd 2 : 40 x 30 lb min 8.0 oz/yd 2 : 60 x 50 min <6.0 oz/yd 2 : 2.5 lb min 6.0-7.9 oz/yd 2 : 3.0 lb min 8.0 oz/yd 2 : 4.0 min Seam Slippage ASTM D1683 20 lbs min @ ¼ Stretch & Recovery ASTM D3107 5% spandex in stretch direction only Stretch: 15% min. Growth: 5% max. Recovery (30 sec/30 min): 90% min Page 18 of 61 July 2014

102F Woven Twill Fabric Page 2 of 2 Abrasion Resistance ASTM D3886 Stretch Twill: 100 cycles min Unwashed: 8.0 oz/yd 2 : 300 cycles min >8.0 oz/yd 2 : 500 cycles min Washed: 8.0 oz/yd 2 : 100 cycles min >8.0 oz/yd 2 : 200 cycles min Colorfastness CF to Home Laundering AATCC 135 CF to Commercial Dry-cleaning AATCC 132 CF to Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Non-Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 CF to Light AATCC 16, Option 3 Provide ratings after 10 & 20 AFU Pass/Fail based on 20 AFU rating only Class 4.0 @ 20 AFU CF to Water AATCC 107 Color block / Contrast trims only CF to Perspiration AATCC 15 *Phenolic Yellowing ISO 105-X18 Solid White or Ivory Class 3.5 Note: Please refer to special claims protocol as applicable. Page 19 of 61 July 2014

Labeling Textile Fiber Products Identification Act Care Labeling Rule Wool Products Labeling Act Analytical *Lead in surface coating (If Requested) 102G Twill Garment Page 1 of 1 CPSC-CH-E1003-09.1 / AOAC 974.02 (mod.) Fiber Content Label RN# or WPL # Country of Origin Care Label Size Physical Characteristics Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) Dimensional Stability-Drycleaning (1 cycle) General Appearance after care (3HL or 1 DC) AATCC 150 AATCC 158 CPSD-SL-31055-MTHD Shall not exceed 90 ppm (0.009% by weight) Seam Skew/Torque AATCC TS-004 5% or ½ maximum Seam Strength ASTM D1683 <6.0 oz/yd 2 : 25 min 6.0-7.9 oz/yd 2 : 30 min 8.0 oz/yd 2 : 35 min Seam Slippage** ASTM D1683 20 lbs min @ ¼ Component Attachment Strength Refer to protocol 800 Pocket Attachment Strength ASTM D1683 MOD 15 lbs min. 100% Cotton: -4% All other: -3% Growth: +1% Shrinkage: -2% No growth No distortion, defects, damaged components, excessive puckering Pilling: Class 4.0 Note: 1. Any components not previously tested are required to test to appropriate standard 2. Please refer to special claims protocol as applicable. **Seam Slippage test the following seams: Tops: Side, Shoulder, Yoke, Armhole, Sleeve, Collar & Pocket Bottoms: Side, Inseam, Back Rise, Crotch, Zipper stress area, all pockets Page 20 of 61 July 2014

200F Knit Fabric Page 1 of 2 Analytical ph value AATCC 81 6-8 Flammability Flammability Of Clothing Textiles 16 CFR 1610 Class 1 (if not exempt) All Colors Physical Characteristics *Fiber Analysis AATCC 20/20A 0% Single Fiber ± 3% Blends Fabric Weight ASTM D3776 gm/m 2 ± 5% from claim Fabric Count ASTM D3887 ± 5% from claim Special Fabric Type As claimed Yarn Size (If Claimed) ASTM D1059 ± 5% from claim Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) AATCC 135-5% Growth: +1% Dimensional Stability-Drycleaning (1 cycle) AATCC 158 Shrinkage: -2% No growth General Appearance after care (3HL or 1 DC) Appearance after Ironing Skew/Torque Bursting Strength Pilling Stretch & Recovery CPSD-SL-31055-MTHD Hand Iron AATCC 179 Method 1, Option 1 ASTM D3786 ASTM D3512 ASTM D2594 No distortion, defects, excessive puckering Pilling: Class 4.0 Satisfactory for Double Face Fleece No distortion defects 5% or ½ maximum <120 gm/m 2 : 40 psi 120 gm/m 2 : 55 psi Double Face Fleece with Anti-Pilled treatment claim Satisfactory @ 30 min Refer to Appendix 2 for rating of specimen 5% spandex in stretch direction only Stretch: 15% min. Growth: 5% max. Page 21 of 61 July 2014

200F Knit Fabric Page 2 of 2 Colorfastness CF to Home Laundering AATCC 135 CF to Commercial Dry-cleaning AATCC 132 CF to Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Non-Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 CF to Light AATCC 16, Option 3 Provide ratings after 10 & 20 AFU Pass/Fail based on 20 AFU rating only Class 4.0 @ 20 AFU CF to Water AATCC 107 Color block / Contrast trims only CF to Perspiration AATCC 15 *Phenolic Yellowing ISO 105-X18 Solid White or Ivory Class 3.5 Note: Please refer to special claims protocol as applicable. Page 22 of 61 July 2014

Labeling Textile Fiber Products Identification Act Care Labeling Rule Wool Products Labeling Act Analytical *Lead in surface coating (If Requested) 200G Knit Garment Page 1 of 1 CPSC-CH-E1003-09.1 / AOAC 974.02 (mod.) Fiber Content Label RN# or WPL # Country of Origin Care Label Size Shall not exceed 90 ppm (0.009% by weight) Physical Characteristics Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) AATCC 150-5% Growth: +1% Dimensional Stability-Drycleaning (1 cycle) AATCC 158 Shrinkage: -2% No growth General Appearance after care (3HL or 1 DC) CPSD-SL-31055-MTHD No distortion, defects, damaged components, excessive puckering Satisfactory for Double face fleece Pilling: Class 4.0 Seam Skew/Torque AATCC TS-004 5% or ½ maximum Seam Stretchability AATCC TS-015 <120 gm/m 2 : 35% and/or 6 lbs 120 gm/m 2 : 50% and/or 7 lbs Component Attachment Strength Refer to protocol 800 Note: 1. Any components not previously tested are required to test to appropriate standard 2. Please refer to special claims protocol as applicable. Page 23 of 61 July 2014

201F Loungewear / Underwear / Terry Robe / Sleepwear Fabric Page 1 of 2 Analytical ph value AATCC 81 6-8 Flammability Flammability Of Clothing Textiles 16 CFR 1610 Class 1 (if not exempt) All Colors Physical Characteristics *Fiber Analysis AATCC 20/20A 0% Single Fiber ± 3% Blends Fabric Weight ASTM D3776 gm/m 2 ± 5% from claim Fabric Count Woven: ASTM D3775 Knit: ASTM D3887 ± 5% from claim Special Fabric Type As claimed Yarn Size (If Claimed) ASTM D1059 ± 5% from claim Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) AATCC 135 Woven: 100 Cotton: -4% All others: -3% Knit: -5% Growth: +1% General Appearance after care (3HL) CPSD-SL-31055-MTHD No distortion, defects, excessive puckering Pilling: Class 4.0 Appearance after Ironing Hand Iron No distortion defects Skew/Torque AATCC 179 Method 1, Option 1 5% or ½ maximum Seam Slippage (Woven) ASTM D1683 20 lb min @ ¼ Tensile Strength (Woven) ASTM D5034 <6.0 oz/yd 2 : 30 lb min 6.0 oz/yd 2 : 40 lb min Tear Strength (Woven) ASTM D1424 <6.0 oz/yd 2 : 2.5 lb min 6.0-7.9 oz/yd 2 : 3.0 lb min 8.0 oz/yd 2 : 4.0 lb min Bursting Strength (Knit) ASTM D3786 <120 gm/m 2 : 40 psi 120 gm/m 2 : 55 psi Page 24 of 61 July 2014

201F Loungewear / Underwear / Terry Robe / Sleepwear Fabric Page 2 of 2 5% spandex in stretch direction only Stretch & Recovery Woven: ASTM D3107 Stretch: 15% min. Knit: ASTM D2594 Growth: 5% max. Recovery (30 sec/30 min): Min 90% Absorbency ASTM D4772 Terry Robe Only Ultra-absorbency: 75% min Two-sided terry: 65% min One-sided terry: 35% min Colorfastness CF to Home Laundering AATCC 135 CF to Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Non-Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 CF to Light AATCC 16, Option 3 Provide ratings after 10 & 20 AFU Pass/Fail based on 20 AFU rating only Class 4.0 @ 20 AFU CF to Water AATCC 107 Color block / Contrast trims only CF to Perspiration AATCC 15 Excludes Robe Fabric *Phenolic Yellowing ISO 105-X18 Solid White or Ivory Class 3.5 Note: Please refer to special claims protocol as applicable. Page 25 of 61 July 2014

Labeling Textile Fiber Products Identification Act Care Labeling Rule Wool Products Labeling Act Analytical *Lead in surface coating (If Requested) 201G Loungewear / Underwear / Terry Robe / Sleepwear Garment Page 1 of 1 CPSC-CH-E1003-09.1 / AOAC 974.02 (mod.) Fiber Content Label RN# or WPL # Country of Origin Care Label Size Physical Characteristics Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) General Appearance after care (3HL) AATCC 150 CPSD-SL-31055-MTHD Shall not exceed 90 ppm (0.009% by weight) Woven: 100 Cotton: -4% All others: -3% Knit: -5% Growth: +1% No distortion, defects, damaged components, excessive puckering Pilling: Class 4.0 Seam Skew/Torque AATCC TS-004 5% or ½ maximum Loss of Lint No Noticeable Loss (For Terry Robe) Seam Strength (Woven) ASTM D1683 <6.0 oz/yd 2 : 20 lb min 6.0 oz/yd 2 : 25 lb min Seam Slippage (Woven)** ASTM D1683 20 lb min @ ¼ Seam Stretchability AATCC TS-015 <120 gm/m 2 : 35% and/or 6 lbs 120 gm/m 2 : 50% and/or 7 lbs Component Attachment Strength Refer to protocol 800 Pocket Attachment Strength ASTM D1683 mod Woven: 15 lb min Knit: <120 gm/m 2 : 35% and/or 6 lbs 120 gm/m 2 : 50% and/or 7 lbs Note: 1. Any components not previously tested are required to test to appropriate standard 2. Please refer to special claims protocol as applicable. **Seam Slippage: test the following seams: Tops: Side, Shoulder, Yoke, Armhole, Sleeve, Collar & Pocket Bottoms: Side, Inseam, Back Rise, Crotch, Zipper stress area, all pockets Page 26 of 61 July 2014

202F Swim Fabric Page 1 of 2 Analytical ph value AATCC 81 6-8 Flammability Flammability Of Clothing Textiles 16 CFR 1610 Class 1 (if not exempt) All Colors Physical Characteristics *Fiber Analysis AATCC 20/20A 0% Single Fiber ± 3% Blends Fabric Weight ASTM D3776 Woven: oz/yd 2 ; Knit: gm/m 2 ± 5% from claim Fabric Count Woven: ASTM D3775 Knit: ASTM D3887 ± 5% from claim Special Fabric Type As claimed Yarn Size (If Claimed) ASTM D1059 ± 5% from claim Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) AATCC 135 Woven: 100 Cotton: -4% All others: -3% Knit: -5% Growth: +1% General Appearance after care (3HL) CPSD-SL-31055-MTHD No distortion, defects, excessive puckering Pilling: Class 4.0 Appearance after Ironing Hand Iron No distortion defects Skew/Torque AATCC 179 Method 1, Option 1 5% or ½ maximum Seam Slippage (Woven) ASTM D1683 20 lb min @ ¼ Tensile Strength (Woven) ASTM D5034 <6.0 oz/yd 2 : 30 lb min 6.0 oz/yd 2 : 40 lb min Tear Strength (Woven) ASTM D1424 <6.0 oz/yd 2 : 2.5 lb min 6.0-7.9 oz/yd 2 : 3.0 lb min 8.0 oz/yd 2 : 4.0 lb min Bursting Strength (Knit) ASTM D3786 <120 gm/m 2 : 40 psi 120 gm/m 2 : 55 psi Page 27 of 61 July 2014

202F Swim Fabric Page 2 of 2 5% spandex in stretch direction only Stretch & Recovery Woven: ASTM D3107 Stretch: 15% min. Knit: ASTM D2594 Growth: 5% max. Recovery (30 sec/30 min): Min 90% Colorfastness CF to Home Laundering AATCC 135 CF to Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Non-Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 CF to Light AATCC 16, Option 3 Provide ratings after 20 & 40 AFU Pass/Fail based on 40 AFU rating only Class 4.0 @ 40 AFU CF to Water AATCC 107 CF to Perspiration AATCC 15 CF to Sea Water AATCC 106 CF to Pool water AATCC 162 *Phenolic Yellowing ISO 105-X18 Solid White or Ivory Class 3.5 Note: Please refer to special claims protocol as applicable. Page 28 of 61 July 2014

Labeling Textile Fiber Products Identification Act Care Labeling Rule Wool Products Labeling Act Analytical *Lead in surface coating (If Requested) 202G Swimwear Page 1 of 1 CPSC-CH-E1003-09.1 / AOAC 974.02 (mod.) Fiber Content Label RN# or WPL # Country of Origin Care Label Size Physical Characteristics Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) General Appearance after care (3HL or 1 DC) AATCC 150 CPSD-SL-31055-MTHD Shall not exceed 90 ppm (0.009% by weight) Woven: 100 Cotton: -4% All others: -3% Knit: -5% Growth: +1% No distortion, defects, damaged components, excessive puckering Pilling: Class 4.0 Seam Skew/Torque AATCC TS-004 5% or ½ maximum Seam Strength (Woven) ASTM D1683 <6.0 oz/yd 2 : 20 lb min 6.0 oz/yd 2 : 25 lb min Seam Slippage (Woven)** ASTM D1683 20 lb min @ ¼ Seam Stretchability (Knit) AATCC TS-015 <120 gm/m 2 : 35% and/or 6 lbs 120 gm/m 2 : 50% and/or 7 lbs Component Attachment Strength Refer to protocol 800 Pocket Attachment Strength ASTM D1683 mod Woven: 15 lb min Knit: <120 gm/m 2 : 35% and/or 6 lbs 120 gm/m 2 : 50% and/or 7 lbs Note: 1. Any components not previously tested are required to test to appropriate standard 2. Please refer to special claims protocol as applicable. **Seam Slippage: test the following seams: Tops: Side, Shoulder, Yoke, Armhole, Sleeve, Collar & Pocket Bottoms: Side, Inseam, Back Rise, Crotch, Zipper stress area, all pockets Page 29 of 61 July 2014

Labeling Textile Fiber Products Identification Act Care Labeling Rule Wool Products Labeling Act Analytical *Lead in surface coating (If Requested) Flammability 300G Sweaters Page 1 of 2 CPSC-CH-E1003-09.1 / AOAC 974.02 (mod.) Fiber Content Label RN# or WPL # Country of Origin Care Label Size Shall not exceed 90 ppm (0.009% by weight) Flammability Of Clothing Textiles 16 CFR 1610 Class 1 (if not exempt) All Colors Physical Characteristics *Fiber Analysis AATCC 20/20A 0% Single Fiber ± 3% Blends Weight per dozen ASTM D3887 mod ± 5% from claim Fabric Count ASTM D3887 ± 5% from claim Special Fabric Type As claimed Yarn Size (If Claimed) ASTM D1059 ± 5% from claim Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) AATCC 150-5% Growth: +1% Dimensional Stability-Drycleaning (1 cycle) AATCC 158 Shrinkage: -2% No growth No distortion, defects, damaged components, excessive General Appearance after care puckering (3HL or 1 DC) CPSD-SL-31055-MTHD Pilling: Class 4.0 Appearance after Ironing Hand Iron No distortion defects Seam Skew/Torque AATCC TS-004 5% or ½ maximum Seam Stretchability AATCC TS-015 <120 gm/m 2 : 35% and/or 6 lbs 120 gm/m 2 : 50% and/or 7 lbs Bursting Strength ASTM D3786 <120 gm/m 2 : 40 psi 120 gm/m 2 : 50 psi Stretch & Recovery ASTM D2594 5% spandex in stretch direction only Stretch: 15% min. Growth: 5% max. Page 30 of 61 July 2014

300G Sweaters Page 2 of 2 *Pilling Resistance-Wool & Wool blends ICI Pilling box method BS NE ISO 12945-1 Wool blends Class 3.5 @ 4 hours (14,400 revolutions) Cashmere / Luxury fibers: Class 3.5 @2 hours (7,200 revolutions) Component Attachment Strength Refer to protocol 800 Colorfastness CF to Home Laundering AATCC 135 CF to Dry-cleaning Commercial Dryclean CF to Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Non-Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 CF to Light AATCC 16, Option 3 Provide ratings after 10 & 20 AFU Pass/Fail based on 20 AFU rating only Class 4.0 @ 20 AFU CF to Water AATCC 107 Color Block / Contrast Trims only CF to Perspiration AATCC 15 *Phenolic Yellowing ISO 105-X18 Solid White orivory Class 3.5 Note: 1. Any components not previously tested are required to test to appropriate standard 2. Please refer to special claims protocol as applicable. Page 31 of 61 July 2014

400F Leather & Suede Hides Page 1 of 1 Flammability Flammability Of Clothing Textiles 16 CFR 1610 Class 1 (if not exempt) All Colors Physical Characteristics *Fiber Analysis AATCC 20/20A Textile components / lining 0% Single Fiber ± 3% Blends Leather thickness ASTM D1813 report in millimeters ± 5% from claim Defects Report all defects Performance Dimensional Stability- Professional Leather Clean General Appearance after care Professional Leather Clean CPSD-SL-31055-MTHD -2% No Growth No distortion, defects, excessive puckering Pilling: Class 4.0 Seam Slippage ASTM D1683 20 lb min @ ¼ Tensile Strength ASTM D5034 40 lb min Tear Strength ASTM D1424 <6.0 oz/yd 2 : 2.5 lb min 6.0-7.9 oz/yd 2 : 3.0 lb min 8.0 oz/yd 2 : 4.0 lb min Colorfastness CF to Professional Leather Clean Leather Clean-1 cycle CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 CF to Light AATCC 16, Option 3 Provide ratings after 10 & 20 AFU Pass/Fail based on 20 AFU rating only Class 4.0 @ 20 AFU CF to Water AATCC 107 Color block / Contrast trims only *Phenolic Yellowing ISO 105-X18 Solid White or Ivory Class 3.5 Note: Please refer to special claims protocol as applicable. Page 32 of 61 July 2014

400G Leather & Suede Garments Page 1 of 1 Labeling Guide for Select Leather & Imitation Leather Products Textile Fiber Products Identification Act (If Textile lining) Wool Products Labeling Act (if wool lining) Care Labeling Rule Analytical *Lead in surface coating (If Requested) CPSC-CH-E1003-09.1 / AOAC 974.02 (mod.) Leather Identification Fiber Content Label RN# or WPL # Country of Origin Care Label Size Physical Characteristics Defects Report all defects Performance Dimensional Stability- Professional Leather Clean General Appearance after care Professional Leather Clean CPSD-SL-31055-MTHD Seam Strength ASTM D1683 25 lb min Seam Slippage (Woven)** ASTM D1683 20 lb min @ ¼ Component Attachment Strength Refer to protocol 800 Pocket Attachment Strength ASTM D1683 mod 15 lb min Shall not exceed 90 ppm (0.009% by weight) -2% No Growth Differential Shrinkage (Shell/Lining): 2% No distortion, defects, damaged components, excessive puckering Pilling: Class 4.0 Note: 1. Any components not previously tested are required to test to appropriate standard 2. Please refer to special claims protocol as applicable. **Seam Slippage test the following seams: Tops: Side, Shoulder, Yoke, Armhole, Sleeve, Collar & Pocket Bottoms: Side, Inseam, Back Rise, Crotch, Zipper stress area, all pockets Page 33 of 61 July 2014

500F Lining Fabric (Applies for all Textile Items) Page 1 of 2 Analytical ph value AATCC 81 6-8 Flammability Flammability Of Clothing Textiles 16 CFR 1610 Class 1 (if not exempt) All Colors Physical Characteristics *Fiber Analysis AATCC 20/20A 0% Single Fiber ± 3% Blends Fabric Weight Woven: ASTM D3776 Woven: oz/yd 2 ; Knit: gm/m 2 Knit: ASTM D3887 ± 5% from claim Fabric Count Woven: ASTM D3775 Knit: ASTM D3887 ± 5% from claim Special Fabric Type As claimed Yarn Size (If Claimed) ASTM D1059 ± 5% from claim Defects Report all defects Performance Woven: 100 Cotton: -4% All others: -3% Dimensional Stability-Home AATCC 135 Knit: -5% Laundering (3 washes) Growth: +1% Differential Shrinkage (shell/lining): 2% Dimensional Stability-Drycleaning (1 cycle) AATCC 158 Shrinkage: -2% No growth General Appearance after care (3HL or 1 DC) CPSD-SL-31055-MTHD No distortion, defects, excessive puckering Pilling: Class 4.0 Appearance after Ironing Hand Iron No distortion defects Seam Slippage (Woven) ASTM D1683 20 lb min @ ¼ Seam Strength (Woven) ASTM D1683 20 lb min Seam Stretchability AATCC TS-015 <120 gm/m 2 : 35% and/or 6 lbs 120 gm/m 2 : 50% and/or 7 lbs Tensile Strength (Woven) Tear Strength (Woven) ASTM D5034 (Warp x Weft) ASTM D1424 <3.5 oz/yd 2 : 20 lbs min 3.5-6.0 oz/yd 2 : 30 lb min 6.0-7.9 oz/yd 2 : 40 x 30 lb min 8.0 oz/yd 2 : 60 x 50 lb min <3.5 oz/yd 2 : 1.5 lbs min 3.5-6.0 oz/yd 2 : 2.5 lb min 6.0-7.9 oz/yd 2 : 3.0 lb min 8.0 oz/yd 2 : 4.0 lb min Page 34 of 61 July 2014

500F Lining Fabric (Applies for all Textile Items) Page 2 of 2 Bursting Strength (knit) ASTM D3786 <120 gm/m 2 : 40 psi 120 gm/m 2 : 55 psi Component Attachment Strength Refer to protocol 800 Colorfastness CF to Home Laundering AATCC 135/143 CF to Dry-cleaning AATCC 132 CF to Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Non-Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 CF to Light AATCC 16, Option 3 Provide ratings after 10 & 20 AFU Pass/Fail based on 20 AFU rating only Class 4.0 @ 20 AFU CF to Water AATCC 107 Color block / Contrast trims only CF to Perspiration AATCC 15 CF to Sea Water AATCC 106 Swimwear Only CF to Pool Water AATCC 162 Swimwear Only *Phenolic Yellowing ISO 105-X18 Solid White or Ivory Class 3.5 Note: Please refer to special claims protocol as applicable. Page 35 of 61 July 2014

Labeling 600G Textile Hats & Caps Page 1 of 2 Wool Products Labeling Act (if wool lining) Analytical *Lead in surface coating (If Requested) Flammability CPSC-CH-E1003-09.1 / AOAC 974.02 (mod.) Fiber Content Label (If Wool) RN# or WPL # Country of Origin Care Label Shall not exceed 90 ppm (0.009% by weight) Flammability Of Clothing Textiles 16 CFR 1610 Class 1 (if not exempt) All Colors Physical Characteristics *Fiber Analysis AATCC 20/20A 0% Single Fiber ± 3% Blends Fabric Weight ASTM D3776 ± 5% from claim Fabric Count ASTM D3775 ± 5% from claim Yarn Size (If Claimed) ASTM D1059 ± 5% from claim Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) AATCC 150 Woven: 100 Cotton: -4% All others: -3% Knit: -5% Growth: +1% Differential Shrinkage (shell/lining): 2% No distortion, defects, excessive puckering Pilling: Class 4.0 General Appearance after care (3HL) CPSD-SL-31055-MTHD Seam Strength ASTM D1683 10 lb min Seam Stretchability AATCC TS-015 <120 gm/m 2 : 35% and/or 6 lbs 120 gm/m 2 : 50% and/or 7 lbs Bursting Strength (knit) ASTM D3786 <120 gm/m 2 : 40 psi 120 gm/m 2 : 55 psi Component Attachment Strength Refer to protocol 800 Page 36 of 61 July 2014

600G Textile Hats & Caps Page 2 of 2 Colorfastness CF to Home Laundering AATCC 143 CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 CF to Light AATCC 16, Option 3 Provide ratings after 20 & 40 AFU Pass/Fail based on 40 AFU rating only Class 4.0 @ 40 AFU CF to Water AATCC 107 Color block / Contrast trims only CF to Perspiration AATCC 15 *Phenolic Yellowing ISO 105-X18 Solid White or Ivory Class 3.5 Note: Please refer to special claims protocol as applicable. Page 37 of 61 July 2014

Labeling Textile Fiber Products Identification Act Care Labeling Rule Wool Products Labeling Act Analytical *Lead in surface coating (If Requested) Flammability 601G Socks & Hosiery Page 1 of 2 CPSC-CH-E1003-09.1 / AOAC 974.02 (mod.) Flammability Of Clothing Textiles 16 CFR 1610 Physical Characteristics *Fiber Analysis (If requested / Claimed) AATCC 20/20A Fiber Content Label Care Label Country of Origin RN# or WPL # Size Shall not exceed 90 ppm (0.009% by weight) Class 1 (if not exempt) All Colors 0% Single Fiber ± 3% Blends Weight per Dozen Standard Measure ± 5% from claim Fabric Count-Knit ASTM D3887 ± 5% from claim Yarn Size (If Claimed) ASTM D1059 ± 5% from claim Yarn Construction ASTM D1244 As Claimed Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) General Appearance after care (3HL) Abrasion Resistance of Socks (Heel Area) Fit Properties-After Laundering AATCC 150 CPSD-SL-31055-MTHD ASTM D4966 (Mod) CPSD-SL-31006-MTHD *Antifungal (If Claimed) AATCC 30 (Test III) Qualitative Only Subjective evaluation on all sizes after wash No more than 7% shrinkage & the ability to fit NAHM form No distortion, defects, excessive puckering Pilling: Class 4.0 Athletic: 400 cycles minimum Casual / Dress: 200 cycles minimum Sock Stretch: Biaxial stretch: 0.5 lb min 9 lb max Cuff Support: 0.25 lb/in min 4.25 ln/in max Cuff: Correspond to maximum heel girth (inches) Page 38 of 61 July 2014

601G Socks & Hosiery Page 2of 2 Colorfastness CF to Home Laundering AATCC 143 CF to Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Non-Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 CF to Light AATCC 16, Option 3 Provide ratings after 5 & 10 AFU Pass/Fail based on 10 AFU rating only Class 4.0 @ 10 AFU CF to Water AATCC 107 Color block / Contrast trims only CF to Perspiration AATCC 15 *Phenolic Yellowing ISO 105-X18 Solid White or Ivory Class 3.5 Note: Please refer to special claims protocol as applicable. Page 39 of 61 July 2014

700 F Outerwear Fabric (Shell Only) Page 1 of 2 Analytical ph value AATCC 81 6-8 Flammability Flammability Of Clothing Textiles 16 CFR 1610 Class 1 (if not exempt) All Colors Physical Characteristics *Fiber Analysis AATCC 20/20A 0% Single Fiber ± 3% Blends Fabric Weight Woven: ASTM D3776 Woven: oz/yd 2 / Knit: gm/m 2 Knit: ASTM D3887 ± 5% from claim Fabric Count Woven: ASTM D3775 Knit: ASTM D3887 ± 5% from claim Yarn Size (If Claimed) ASTM D1059 ± 5% from claim Defects Report all defects Performance 100% Cotton: -4% All others: -3% Dimensional Stability-Home AATCC 135 Knit: -5% Laundering (3 washes) Growth: +1% Differential shrinkage (Shell/lining): 2% Dimensional Stability-Drycleaning (1 cycle) General Appearance after care (3HL or 1 DC) Appearance after Ironing Skew/Torque AATCC 158 CPSD-SL-31055-MTHD Hand Iron AATCC 179 Method 1, Option 1 Note: Mandatory for outerwear Shrinkage: -2% No growth No distortion, defects, excessive puckering Pilling: Class 4.0 No distortion defects 5% or ½ maximum Tensile Strength (Woven) ASTM D5034 <3.5 oz/yd 2 : 25 lb min 3.5-5.9 oz/yd 2 : 30 lb min 6.0-7.9 oz/yd 2 : 40x 30 lb min 8.0 oz/yd 2 : 60x 50 lb min Tear Strength (Woven) ASTM D1424 <3.5 oz/yd 2 : 1.5 lb min 3.5-5.9 oz/yd 2 : 2.5 lb min 6.0-7.9 oz/yd 2 : 3.0 lb min 8.0 oz/yd 2 : 4.0 lb min Seam Slippage (Woven) ASTM D1683 20 lbs min @ ¼ Page 40 of 61 July 2014

700 F Outerwear Fabric (Shell Only) Page 2 of 2 Bursting Strength (Knit) ASTM D3786 <120 gm/m 2 : 40 psi 120 gm/m 2 : 55 psi Stretch & Recovery ASTM D3107 5% spandex in stretch direction only Stretch: 15% min. Growth: 5% max. Woven: Recovery (30 sec/30 min): Min 90% Colorfastness CF to Home Laundering AATCC 135 CF to Commercial Dry-cleaning AATCC 132 CF to Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Non-Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 CF to Light AATCC 16, Option 3 Provide ratings after 10/20 & 20/40 AFU Pass/Fail based on 20/40 AFU rating only Shell: Class 4.0 @ 40 AFU Lining: Class 4.0 @ 20 AFU CF to Water AATCC 107 Color block / Contrast trims only *Phenolic Yellowing ISO 105-X18 Solid White or Ivory Class 3.5 Note: Please refer to special claims protocol as applicable. Page 41 of 61 July 2014

Labeling Textile Fiber Products Identification Act Care Labeling Rule Wool Products Labeling Act Analytical *Lead in surface coating (If Requested) 700G Outerwear Garment (With or Without Lining) Page 1 of 1 CPSC-CH-E1003-09.1 / AOAC 974.02 (mod.) Fiber Content Label Care Label Country of Origin RN# or WPL # Size Physical Characteristics Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) Dimensional Stability-Drycleaning (1 cycle) General Appearance after care (3HL or 1 DC) AATCC 150 AATCC 158 CPSD-SL-31055-MTHD Shall not exceed 90 ppm (0.009% by weight) Woven: 100% Cotton: -4% All others: -3% Knit: -5% Growth: +1% Differential Shrinkage (Shell/lining): 2% Note: Mandatory for outerwear Shrinkage: -2% No growth No distortion, defects, damaged components, excessive puckering Pilling: Class 4.0 Seam Skew/Torque AATCC TS-004 5% or ½ maximum Seam Strength ASTM D1683 25 lbs min. Seam Slippage** ASTM D1683 20 lbs min @ ¼ Seam Stretchability AATCC / ASTM TS-015 <120 gm/m 2 : 35% and/or 6 lb 120 gm/m 2 : 50% and/or 7 lb Component Attachment Strength Refer to protocol 800 Pocket Attachment Strength ASTM D1683 mod <120 gm/m 2 : 35% and/or 6 lb 120 gm/m 2 : 50% and/or 7 lb Note: Please refer to special claims protocol as applicable. **Seam Slippage test the following seams: Tops: Side, Shoulder, Yoke, Armhole, Sleeve, Collar & Pocket Bottoms: Side, Inseam, Back Rise, Crotch, Zipper stress area, all pockets Page 42 of 61 July 2014

701F Sports Coats / Jackets, Suits Fabric (Shell Only) Page 1 of 2 Analytical ph value AATCC 81 6-8 Flammability Flammability Of Clothing Textiles 16 CFR 1610 Class 1 (if not exempt) All Colors Physical Characteristics *Fiber Analysis AATCC 20/20A 0% Single Fiber ± 3% Blends Fabric Weight Woven: ASTM D3776 Woven: oz/yd 2 / Knit: gm/m 2 Knit: ASTM D3887 ± 5% from claim Fabric Count Woven: ASTM D3775 Knit: ASTM D3887 ± 5% from claim Special Fabric Type As claimed Yarn Size (If Claimed) ASTM D1059 ± 5% from claim Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) AATCC 135 100% Cotton: -4% All others: -3% Knit: -5% Suede Fleece Thermal: -5% x -8% Growth: +1% Differential shrinkage (Shell/lining): 2% Dimensional Stability-Drycleaning (1 cycle) General Appearance after care (3HL or 1 DC) Appearance after Ironing Skew/Torque AATCC 158 CPSD-SL-31055-MTHD Hand Iron AATCC 179 Method 1, Option 1 Mandatory Shrinkage: -2% No growth No distortion, defects, excessive puckering Pilling: Class 4.0 No distortion defects 5% or ½ maximum Tensile Strength (Woven) ASTM D5034 <3.5 oz/yd 2 : 25 lb min 3.5-5.9 oz/yd 2 : 30 lb min 6.0-7.9 oz/yd 2 : 40x 30 lb min 8.0 oz/yd 2 : 60x 50 lb min Tear Strength (Woven) ASTM D1424 <3.5 oz/yd 2 : 1.5 lb min 3.5-5.9 oz/yd 2 : 2.5 lb min 6.0-7.9 oz/yd 2 : 3.0 lb min 8.0 oz/yd 2 : 4.0 lb min Seam Slippage (Woven) ASTM D1683 20 lbs min @ ¼ Page 43 of 61 July 2014

701F Sports Coats / Jackets, Suits Fabric (Shell Only) Page 2 of 2 Bursting Strength (Knit) ASTM D3786 <120 gm/m 2 : 40 psi 120 gm/m 2 : 55 psi Stretch & Recovery ASTM D3107 5% spandex in stretch direction only Stretch: 15% min. Growth: 5% max. Woven: Recovery (30 sec/30 min): Min 90% Colorfastness CF to Home Laundering AATCC 135 CF to Commercial Dry-cleaning AATCC 132 CF to Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Non-Chlorine Bleach AATCC TS-001 With Suppressor for pastels only Class 4.0 CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 CF to Light AATCC 16, Option 3 Provide ratings after 10 & 20 AFU Pass/Fail based on 20 AFU rating only Class 4.0 @ 20 AFU CF to Water AATCC 107 Color block / Contrast trims only *Phenolic Yellowing ISO 105-X18 Solid White or Ivory Class 3.5 Note: Please refer to special claims protocol as applicable. Page 44 of 61 July 2014

Labeling Textile Fiber Products Identification Act Care Labeling Rule Wool Products Labeling Act Analytical *Lead in surface coating (If Requested) 701G Sports Coats / Jackets, Suits (With or Without Lining) Page 1 of 1 CPSC-CH-E1003-09.1 / AOAC 974.02 (mod.) Fiber Content Label Care Label Country of Origin RN# or WPL # Size Physical Characteristics Defects Report all defects Performance Dimensional Stability-Home Laundering (3 washes) Dimensional Stability-Drycleaning (1 cycle) General Appearance after care (3HL or 1 DC) AATCC 150 AATCC 158 CPSD-SL-31055-MTHD Shall not exceed 90 ppm (0.009% by weight) 100% Cotton: -4% All others: -3% Knit: -5% Suede Fleece Thermal: -5% x -8% Growth: +1% Differential shrinkage (Shell/lining): 2% Mandatory Shrinkage: -2% No growth No distortion, defects, damaged components, excessive puckering Pilling: Class 4.0 Seam Skew/Torque AATCC TS-004 5% or ½ maximum Seam Strength (Woven) ASTM D1683 25 lbs min. Seam Slippage** (Woven) ASTM D1683 20 lbs min @ ¼ Seam Stretchability (Knit) AATCC / ASTM TS-015 <120 gm/m 2 : 35% and/or 6 lb 120 gm/m 2 : 50% and/or 7 lb Component Attachment Strength Refer to protocol 800 Pocket Attachment Strength ASTM D1683 mod <120 gm/m 2 : 35% and/or 6 lb 120 gm/m 2 : 50% and/or 7 lb Note: Please refer to special claims protocol as applicable. **Seam Slippage test the following seams: Tops: Side, Shoulder, Yoke, Armhole, Sleeve, Collar & Pocket Bottoms: Side, Inseam, Back Rise, Crotch, Zipper stress area, all pockets Page 45 of 61 July 2014

EU Market Requirements By Request Only or if indicated as Country of Destination Page 1 of 1 EU Market if requested Analytical Azo Colourants EN 14362-1:2012 / ISO 17234-1:2010 <30 mg/kg Nickel Spot Test PD CR 12471 Negative Nickel Leaching EN1811:2011 / If Requested EN12472:2005+A1:2009 <0.2 µg /cm 2 /week Formaldehyde Spot Test AATCC 94 Negative Formaldehyde Quantitative EN ISO 14184-1:2011 If Requested or Nylon fiber included <75 mg/kg Sleepwear Flammability Nightwear (Safety Regulations) Comply Fiber Label Verification Determined by general garment testing procedures Comply Care Symbol / Wording Verification Determined by general garment testing procedures Comply Page 46 of 61 July 2014

800 Components Page 1 of 2 Button Effects of Washing / Dry-cleaning AATCC 150 3 washes or 1 commercial dryclean No Chipping, cracking, paint loss No color transfer No corrosion *Lead in surface coatings CPSC-CH-E1003-09.1 / If Requested AOAC 974.02 (mod.) Shall not exceed 90 ppm (0.009% by weight) *Lead in substrate CPSD-AN-00185-MTHD / If Requested CPSD-AN-00196-MTHD Shall not exceed 100 ppm (0.01% by weight) Attachment strength ASTM D7142 15 lbs @ 10 seconds Manufacturing Qualities No sharp points or edges Shank Button Effects of Washing / Dry-cleaning AATCC 150 3 washes or 1 commercial dryclean No Chipping, cracking, paint loss No color transfer No corrosion *Lead in surface coatings CPSC-CH-E1003-09.1 / If Requested AOAC 974.02 (mod.) Shall not exceed 90 ppm (0.009% by weight) *Lead in substrate CPSD-AN-00185-MTHD / If Requested CPSD-AN-00196-MTHD Shall not exceed 100 ppm (0.01% by weight) Attachment strength Pull Method Straight position: Min 80 lbs Slant position @ 60 : Min 80 lbs Report actual data until break, specify if shank broke or fabric rupture Manufacturing Qualities No sharp points or edges Snap Effects of Washing / Dry-cleaning AATCC 150 3 washes or 1 commercial dryclean No Chipping, cracking, paint loss No color transfer No corrosion *Lead in surface coatings CPSC-CH-E1003-09.1 / If Requested AOAC 974.02 (mod.) Shall not exceed 90 ppm (0.009% by weight) *Lead in substrate CPSD-AN-00185-MTHD / If Requested CPSD-AN-00196-MTHD Shall not exceed 100 ppm (0.01% by weight) Attachment strength ASTM D7142 15 lbs @ 10 seconds Manufacturing Qualities No sharp points or edges Page 47 of 61 July 2014

Zipper 800 Components Page 2 of 2 Effects of Washing / Dry-cleaning AATCC 150 *Lead in surface coatings *Lead in substrate Attachment strength CPSC-CH-E1003-09.1 / AOAC 974.02 (mod.) CPSD-AN-00185-MTHD / CPSD-AN-00196-MTHD ASTM D2061 3 washes or 1 commercial dryclean No Chipping, cracking, paint loss No color transfer No corrosion If Requested Shall not exceed 90 ppm (0.009% by weight) If Requested Shall not exceed 100 ppm (0.01% by weight) Top Stop, Zip/Unzip, Bottom Stop, Slider Lock & Tab See Zipper Requirements Manufacturing Qualities No sharp points or edges Other Hardware (Including Fabric with two layers) Effects of Washing / Dry-cleaning AATCC 150 3 washes or 1 commercial dryclean No Chipping, cracking, paint loss No color transfer No corrosion Attachment strength Pull Method Report data Manufacturing Qualities No sharp points or edges *Lead in substrate CPSD-AN-00185-MTHD / If Requested CPSD-AN-00196-MTHD Shall not exceed 100 ppm (0.01% by weight) Page 48 of 61 July 2014

801 Elastic Page 1 of 1 Physical Characteristics Elastic Width (mm) Standard Measure As claimed Elastic Weight ASTM D3776 Report actual data Elastic Construction ASTM D37775 Report actual data Yarn Size (If Claimed) ASTM D1059 Report actual data Number of Elastic Yarns Report actual data Wrapped Yarns Report actual data Construction/workmanship No Major defects Performance Dimensional Stability-Home Laundering (3 washes) AATCC 150-4% +1% growth Dimensional Stability-Drycleaning (1 cycle) AATCC 158 Shrinkage: -2% No growth General Appearance after care (3HL or 1 DC) Elastic Memory (Narrow Elastic) Stretch & Recovery CPSD-SL-31055-MTHD ASTM D5278 ASTM D3107 No distortion, defects, excessive puckering Pilling: Class 4.0 Stretch at 20 lbf: Length 120-185% Recovery at 60 sec: Length min 85% Stretch: One Way stretch: 20% min Two way stretch: 15% min Growth: 4% maximum Recovery: <5% spandex: 85% recovery @ 60 min 5% spandex: 90% recovery @ 60 min Colorfastness CF to Home Laundering AATCC 135 CF to Commercial Dry-cleaning AATCC 132 CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.0 CF to Perspiration AATCC 15 ph Value AATCC 81 6-8 *Phenolic Yellowing ISO 105-X18 Solid White or Ivory Class 3.5 Page 49 of 61 July 2014

Labeling 803 Belts Page 1 of 2 Uniform Packaging and Labeling Regulations (Applicable to the Packaging Materials) NIST Uniform Laws and Regulations Handbook 130 Country of Origin Marking 19 CFR 134 Use labeling Manufacturer, Packer, or Distributor s Name & Address (City, State & Zip). Product Identification Net quantity of contents shall be expressed in terms of weight or mass, measure, numerical count, or combination so as to give accurate information to facilitate consumer comparison (U.S. and metric units). Shall indicate country of origin legibly, permanently, and in comparable size and close proximity to any mention of country other than country in which the article was manufactured or produced. Must be visible at point of purchase. Use/Care instructions that are clear and understandable shall be provided in language appropriate to destination Claim verification - level 2 CPSD-GB-08612-MTHD Examine the retail packaging (or submitted artwork). Record each objective (factual) claim which can be substantiated by the testing within the protocols and rate accordingly. Record testing that extends beyond existing net quantity / dimensional testing on this protocol. Record all other objective (factual) and subjective (opinion) claims as NT and rate as DATA. Record information evaluated between the graphic imagery and the product. Analytical *Lead in surface coating (If Requested) Physical Characteristics Dimensions Number of Holes CPSC-CH-E1003-09.1 / AOAC 974.02 (mod.) CPSD-HL-01056-MTHD (Standard Measurement) CPSD-HL-01056-MTHD (Standard Measurement) Material Weight ASTM D3776-96 Sharp Point/ Edges Defects / Workmanship 16 CFR 1500.48/ 1500.49 (Modified) CPSD-HL-01057-MTHD () Shall not exceed 90 ppm (0.009% by weight) Report overall dimensions; shall meet label claims -0% / +2% Report all. Shall meet specification oz/yd 2 ±3.0% from claim Shall Have No Sharp Points/ Edges, Other Than Those Required For Function Shall have no discernible surface degradation, including crazing, shivering Shall have no components missing, malformed and / or fractured Page 50 of 61 July 2014

803 Belts Page 2 of 2 Performance Functionality CPSD-GB-01058-MTHD Shall function as intended. Effects Of Extreme Temperature CPSD-HL-01012-MTHD No failure @ 24 Hours at 0 F and 140 F Effects of Humidity CPSD-HL-01007-MTHD No change after 48 hours @ 95% RH @ 95 F Buckle Strength/Buckle Durability Actual Use No failure after 500 cycles of operation Buckle/Strap Strength ASTM D5034-95 Original, After Humidity & After Cold (0 F) 100 lbs / In (min) Belt hole rupture resistance ASTM D5034 mod 20 Lbs Minimum Bonding Strength CPSD-SL-81003-MTHD 22 Lbs/4 in Tensile Strength ASTM D5034 mod 40 Lbs Minimum Tear Strength (Textile only) ASTM D1424 mod 3 Lbs x 3 Lbs Minimum Belt Loop Attachment ASTM D5034 mod 15 Lbs Minimum Stitch Reinforcement Strength CPSD-SL-81005-MTHD 35 Lbs Minimum (Functional) Flexing CPSD-SL-81002-MTHD 50,000 cycles minimum Cycling Test ASTM D5034 mod 50 cycles @ 175 lbf and 0 lbf Buckle / Clasp Functionality Actual Use No fractures / breakage of buckle / clasp Colorfastness CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.5 CF to Perspiration AATCC 15 (mod) Back side of belt at the front area: Class 3.0 minimum Buckle: No discoloration or degradation of surface finish/color Page 51 of 61 July 2014

Labeling 804 Suspenders Page 1 of 2 Uniform Packaging and Labeling Regulations (Applicable to the Packaging Materials) NIST Uniform Laws and Regulations Handbook 130 Country of Origin Marking 19 CFR 134 Use labeling Manufacturer, Packer, or Distributor s Name & Address (City, State & Zip). Product Identification Net quantity of contents shall be expressed in terms of weight or mass, measure, numerical count, or combination so as to give accurate information to facilitate consumer comparison (U.S. and metric units). Shall indicate country of origin legibly, permanently, and in comparable size and close proximity to any mention of country other than country in which the article was manufactured or produced. Must be visible at point of purchase. Use/Care instructions that are clear and understandable shall be provided in language appropriate to destination Claim verification - level 2 CPSD-GB-08612-MTHD Examine the retail packaging (or submitted artwork). Record each objective (factual) claim which can be substantiated by the testing within the protocols and rate accordingly. Record testing that extends beyond existing net quantity / dimensional testing on this protocol. Record all other objective (factual) and subjective (opinion) claims as NT and rate as DATA. Record information evaluated between the graphic imagery and the product. Analytical *Lead in surface coating (If Requested) Physical Characteristics Total Length Total Width Thickness Total Weight Fit/Measurements Sharp Point/ Edges CPSC-CH-E1003-09.1 / AOAC 974.02 (mod.) CPSD-HL-01056-MTHD (Standard Measurement) CPSD-HL-01056-MTHD (Standard Measurement) CPSD-HL-01056-MTHD (Standard Measurement) CPSD-HL-01056-MTHD (Standard Measurement) CPSD-HL-01056-MTHD (Standard Measurement) 16 CFR 1500.48/ 1500.49 (Modified) Shall not exceed 90 ppm (0.009% by weight) Shall meet label claims (-0% / +2%) Shall meet label claims (-0% / +2%) Shall meet label claims (-0% / +2%) Shall meet label claims (-0% / +2%) Tape measure end to end Shall Have No Sharp Points/ Edges, Other Than Those Required For Function Page 52 of 61 July 2014

Defects / Workmanship 804 Suspenders Page 2 of 2 CPSD-HL-01057-MTHD () Shall have no discernible surface degradation, including crazing, shivering Shall have no components missing, malformed and / or fractured Performance Functionality CPSD-GB-01058-MTHD Shall function as intended. Effects Of Extreme Temperature CPSD-HL-01012-MTHD No failure @ 24 Hours at 0 F and 140 F Effects of Humidity CPSD-HL-01007-MTHD No change after 48 hours @ 95% RH @ 95 F Spirality / torque (If washable) AATCC 179 5% maximum Seam stretchability - knit ASTM D3786 mod Original, After Humidity & After Extreme Temperature <3.5 oz/yd 2 : Minimum 30% Elongation or 6.0lb load 3.5 oz/ yd 2 :Minimum 50% Elongation or 7.0lb Load Abrasion Resistance ASTM D3886 Original, After Humidity & After Extreme Temperature Min. 300 Cycles Stretch and Recovery ASTM D4964 Original, After Humidity & After Extreme Temperature Calculate 95% (min) recovery when stretch to max or over 100% of original length Strength at Elastic and other Original, After Humidity & After Extreme Temperature ASTM D 1683 (Mod) joining area 100 Lbs. / In. (Min) Clip attachment strength ASTM D5034 mod. Original, After Humidity & After Extreme Temperature 75 lbs/in. Minimum Clip Durability Actual Use Original, After Humidity & After Extreme Temperature Shall be no failure or loose in serviceability after 500 cycles Open/closed. (Clip and unclip) Clip performance strength ASTM D5034 mod Original, After Humidity & After Extreme Temperature Shall be able to clip and hold on the 2 layer of 8 oz/sqyd woven fabric when 50 lbs force is applied Resistance To Corrosion ASTM B117 (Modified) Metal Components Shall withstand 24 hours in 1% salt spray (fog) with no corrosion or visual change. Modification = 1% salt (fog) spray. Also report if entire item was placed in the chamber or if only certain pieces/sections. If pieces/sections were tested, list which piece/section, indicate pass or fail for each piece/section, and include before and after pictures of each piece/section Colorfastness CF to Crocking AATCC 8/116 Dry Class 4.0 Wet Class 3.5 CF to Perspiration AATCC 15 Back side of suspenders: Class 3.0 minimum Buckle: No discoloration or degradation of surface finish/color Page 53 of 61 July 2014

802 Special Claims Page 1 of 4 *Antibacterial activity assessment of textile materials *Water Vapor transmission *Air Permeability AATCC 147 ASTM E96 (b) Upright Cup Method ASTM D737 *Absorbency AATCC 79 *Water wicking test AATCC 197 *Water repellency: Spray test AATCC 22 *Oil repellency AATCC 118 *Water Resistance: rain test AATCC 35 *Waterproof AATCC 127 option 2 or ASTM D751 option A *Soil release: oily stain method AATCC 130 If Claimed Anti-Microbial or Anti-Bacterial No bacterial colonies in contact area Test Original & after 20 HL All colors must be tested Test Original & after 3 HL-Breathable Fabrics 500 g/m 2 / 24 hours Test Original & after 3 HL-Windproof claim 1.0 mm/s max. Moisture management Test Original only Maximum 30 seconds Moisture management-if claimed Test Original & after 5 HL All colors 3 inches minimum at 30 minutes Test Original & after 5 HL Original: ISO 90 minimum After 5 washes: ISO 70 minimum Test all colors for 3 in 1 or 4 in 1 premium pants Stain proof claims Test Original & after 5 HL Original: minimum 6 After 5 washes: minimum 4 If claimed water resistant Less than 1 gram Customs test on garments: no more than 1 gm of water penetration at 600 mm pressure for a 2 min duration If claimed Waterproof 2000 mm w.c. (200 cm w.c. or 196 mbar or 2.86 psi) Test Original & after 5 HL If claimed Original: Grade 3.5 After 5 washes: Grade 3.0 Test all colors for 3 in 1 or 4 in 1 premium pants Page 54 of 61 July 2014

802 Special Claims Page 2 of 4 *Wrinkle resistance / durable press Evaluate Original & after 5 HL Test all colors for 3 in 1 or 4 in 1 premium pants AATCC 143 Formaldehyde Spot Test AATCC 94 *Formaldehyde *Size Sticker Evaluation JIS L1041 Lab method Heat: 120 ±2 degrees for 300 hours Durability & Residue: 120 ±2 degrees, 95% relative humidity for 6 hours *Anti-Fade AATCC 150 *Anti-pill AATCC 150 Wrinkle Free or Non Iron Claims Post-cure process Smoothness: Grade 4 min Pocket Seam: Grade 4 min #Seams: Grade 4 min Pleats/Creases: Grade 4 min Wrinkle Resistant Claims Pre-Cure Process Smoothness: Grade 3.5 min Pocket Seam: Grade 3.5 min Seams: Grade 3.5 min Post-cure process Smoothness: Grade 3.5 min Pocket Seam: Grade 3.5 min #Seams: Grade 3.5 min Pleats/Creases: Grade 3.5 min Easy Care Claims Smoothness: Grade 3 min Pocket Seam: Grade 3 min #Seams: Grade 3 min Pleats/Creases: Grade 3 min #Seams include collar, yoke, shoulder, cuffs, center placket, front closure, fly, side seams, inseam) Wrinkle Free / Durable Press Garment Only Negative If spot is positive only <75 ppm Effects of heat on sticker: no wrinkling, de-bonding or curling Rate stickers durability & residue on fabrics No heavy amount of fiber fills on stickers No amount of adhesive residue remaining on stickers Color change on fabric: Class 4.0 If claimed All Colors Evaluate after 5 / 10 / 15 / 20 washes minimum If claimed Evaluate after 5 / 10 / 15 / 20 washes Pilling: Class 4.0 minimum Page 55 of 61 July 2014

802 Special Claims Page 3 of 4 *Non Roll Collar AATCC 150 If claimed Evaluate after 5 / 10 / 15 / 20 washes Collar retains without rolling defect *Unbreakable Buttons AATCC 143 If claimed AATCC 143: Evaluate 30 buttons after 5 / 10 / 15 / 20 washes No chips, cracks or breakage ASTM D5171: Evaluate 30 buttons under 5.5 in-oz impact energy No chips, cracks or breakage If claimed *Durability of Flocking Rate after 3 washes AATCC 150 No obvious defects/observations affecting the end Per Care instructions performance / appearance, color change, staining, satisfactory performance of the components and trims *Tagless Labels AATCC 150 Screen Print, Pad Print & Heat-Set transfer Wash or dryclean according to proposed care method. Evaluate and record comments after 5,10,15,20 wash/dry cycle or 5 dryclean cycles Appearance: No fraying, unraveling, cracking, peeling, text must be legible *Ultra violet protection factor (UPF) *Thermal transmittance of textile materials *Feather & down: Content Analysis AATCC 183-2004 / ASTM D6544-00 (2007) / ASTM D6603-10 ASTM D1518 ASTM D4524-86 (2005 / IDFB 3 If claimed Perform on original and after simulated use & care (as prepared per ASTM D6544) Report UPF rating only The UPF rating shall be given as per ASTM D6603 as below: 15-24: Good UV protection 25-39: Very good UV protection 40-50+: Excellent UV protection If claimed Report result or verify claim (1 rep) 0.6 CLO Original As specified (for labeling for the USA (ADA) Textile Labeling Guidelines for Feather & Down) 2-3% tolerance *Feather and down: Fill Power IDFB 10-B Original Steam conditioning If no claim is made report value only If claimed(min): + or 5% Page 56 of 61 July 2014

802 Special Claims Page 4 of 4 *Feather and down: Turbidity IDFB 11-A Original 300 mm minimum US measurement Hypoallergenic/Super Clean Claim: 500 mm minimum *Feather and down: oxygen number IDFB 21/IDFB 7 JIS 6.6 EN 1162 *Feather and down: odor IDFL Original No putrid odor *Feather and down: fat and oil IDFB 4 Original 0.7% min 2.0% max *Feather and down: downproofness FTM 191-A Method 5530 (mod) Original Less than 10 Hypoallergenic/Super Clean Claim: Less than 5 Original Grade 4 min Page 57 of 61 July 2014

Zipper Requirements Page 1 of 4 Fastener Class (Chain Width: inch) Zipper Item Chain Width: inch) Chain Crosswise Strength Separating Unit Crosswise Strength Element Pull Off Strength Element Slippage Strength Slider Lock Holding Strength 1-2 (0.125-0.180) 3-4 (0.125-0.180) 0.169 0.169 0.163 0.193 0.177 0.177 0.185 0.163 Brass Aluminum CEF CEF Brass Aluminum Plastic CEF kgf N lbs kgf N lbs kgf N lbs kgf N lbs kgf N lbs kgf N lbs kgf N lbs kgf N lbs 35.0 343.0 77.2 25.0 245.0 55.1 35.0 343.0 77.2 40.0 392.0 88.2 55.0 539.0 121.3 35.0 343.0 77.2 27.0 264.6 59.5 40.0 392.0 88.2 9.0 88.2 19.8 9.0 88.2 19.8 - - - - - - 9.0 88.2 19.8 9.0 88.2 19.8 9.0 88.2 19.8 6.0 58.8 13.2 3.5 34.3 7.7 2.4 23.5 5.3 - - - - - - 6.0 58.8 13.2 3.5 34.3 7.7 2.5 24.5 5.5 - - - 2.7 26.5 6.0 2.4 23.5 5.3 - - - - - - 4.5 44.1 9.9 2.7 26.5 6.0 3.5 34.3 7.7 - - - 4.0 39.2 8.58 3.3 37.2 8.4 2.0 19.6 4.4 2.5 24.5 5.5 9.0 88.2 19.8 4.0 39.2 8.8 3.0 29.4 6.6 2.0 19.6 4.4 Tab Pull Off (90 ) 15.0 147.0 33.1 15.0 147.0 33.1 8.0 78.4 17.6 8.0 78.4 17.6 18.0 176.4 39.7 15.0 147.0 33.1 12.0 117.6 26.5 8.0 78.4 17.6 Tab Twist Off 3.0 29.4 2.6 3.0 29.4 2.6 1.5 14.7 1.3 1.5 14.7 1.3 4.6 45.1 4.0 3.0 29.4 2.6 3.0 29.4 2.6 2.0 19.6 1.7 Operability 0.30 2.94 0.66 0.30 2.94 0.66 0.50 4.90 1.10 0.50 4.90 1.10 0.35 3.43 0.77 0.35 3.43 0.77 0.50 4.90 1.10 0.40 3.92 0.88 (open/close) Top Stop Holding Strength Bottom Stop Holding, Stringer Separation 7.0 68.6 15.4 7.0 68.6 15.4 7.0 68.6 15.4 9.0 88.2 19.8 9.0 88.2 19.8 8.0 78.4 17.6 8.0 78.4 17.6 8.0 78.4 17.6 5.0 49.0 11.0 4.5 44.1 9.9 3.0 29.4 6.6 3.5 34.3 7.7 8.0 78.4 17.6 6.0 58.8 13.2 5.0 49.0 11.0 7.0 Plastic Bottom 5.0 49.0 Slider Type DA DA DA DA GS DA DA DA 68.6 15.4 11.0 Page 58 of 61 July 2014

Zipper Requirements Page 2 of 4 Fastener Class (Chain Width: inch) Zipper Item Chain Width: inch) Chain Crosswise Strength Separating Unit Crosswise Strength Element Pull Off Strength Element Slippage Strength Slider Lock Holding Strength Tab Pull Off (90 ) 5-7 (A) (0.180-0.310) 0.197 0.226 0.226 0.226 0.224 0.203 0.203 0.256 Brass Brass Brass Aluminum Plastic Plastic CEF CEF kgf N lbs kgf N lbs kgf N lbs kgf N lbs kgf N lbs kgf N lbs kgf N lbs kgf N lbs 60.0 588.0 132.3 65.0 637.0 143.3 50.0 490.0 110.3 50.0 490.0 110.3 40.0 392.0 88.2 32.0 313.6 70.6 55.0 539.0 121.3 65.0 637.0 143.3 10.0 98.0 22.1 12.0 117.6 26.5 12.0 117.6 26.5 12.0 117.6 26.5 12.0 117.6 26.5 11.0 107.8 24.3 6.0 78.4 17.6 12.0 117.6 26.5 7.5 73.5 16.5 9.0 88.2 19.8 6.0 58.8 13.2 6.0 58.8 13.2 5.0 49.0 11.0 3.5 34.3 7.7 - - - - - - 4.5 44.1 9.9 5.0 49.0 11.0 4.5 44.1 9.9 4.0 39.2 8.8 5.0 49.0 11.0 4.0 39.2 8.8 - - - - - - 10.0 98.0 22.1 11.0 107.8 24.3 6.0 58.8 13.2 6.0 58.8 13.2 3.5 34.3 7.7 4.0 39.2 8.8 3.0 29.4 6.6 5.0 49.0 11.0 20.0 196.0 44.1 25.0 245.0 55.1 18.0 176.4 39.7 18.0 176.4 39.7 18.0 176.4 39.7 15.0 147.0 33.1 18.0 176.4 39.7 25.0 245.0 55.1 Tab Twist Off 4.6 45.1 4.0 5.0 49.0 4.3 5.0 49.0 4.3 5.0 49.0 4.3 5.0 49.0 4.3 4.0 39.2 3.5 4.5 44.1 3.9 5.0 49.0 4.3 Operability 0.45 4.41 0.99 0.50 4.90 1.10 0.50 4.90 1.10 0.40 3.92 0.88 0.70 6.86 1.54 0.70 6.86 1.54 0.50 4.90 1.10 0.70 6.86 1.54 (open/close) Top Stop Holding Strength Bottom Stop Holding, Stringer Separation 10.0 98.0 22.1 11.0 107.8 24.3 10.0 98.8 22.1 10.0 98.0 22.1 10.0 98.0 22.1 9.0 88.2 19.8 9.0 88.2 19.8 12.0 117.6 26.6 9.0 88.2 19.8 11.0 107.8 24.3 8.0 78.4 17.6 9.0 88.2 19.8 9.0 88.2 19.8 6.0 58.8 13.2 10.0 98.0 22.1 12.0 117.6 26.6 Plastic Bottom 8.0 78.4 17.6 10.0 98.0 Slider Type GS GS DA DA DA DA DA DA 22.1 Page 59 of 61 July 2014

Zipper Requirements Page 3 of 4 Fastener Class (Chain Width: inch) Zipper Item Chain Width: inch) 5-7 (B) (0.180-0.310) 0.252 0.252 0.283 Brass Aluminum CEF kgf N lbs kgf N lbs kgf N lbs Chain Crosswise Strength 65.0 637.0 143.3 40.0 392.0 88.2 80.0 784.0 176.4 Separating Unit Crosswise 15.0 147.0 33.1 15.0 147.0 33.1 15.0 147.0 33.1 Strength Element Pull Off Strength 8.0 78.4 17.6 5.0 49.0 11.0 - - - Element Slippage Strength 5.5 53.9 12.1 4.5 44.1 9.9 - - - Slider Lock Holding Strength 6.0 58.8 13.2 6.0 58.8 13.2 6.0 58.8 13.2 Tab Pull Off (90 ) 20.0 196.0 44.1 20.0 196.0 44.1 25.0 245.0 55.1 Tab Twist Off 6.0 58.8 5.2 6.0 58.8 5.2 7.0 68.6 6.1 Operability (open/close) 0.60 5.88 1.32 0.60 5.88 1.32 0.70 6.86 1.54 Top Stop Holding Strength 13.0 127.4 28.7 13.0 127.4 28.7 13.0 127.4 28.7 10.0 98.0 22.1 10.0 98.0 22.1 14.0 137.2 30.9 Bottom Stop Holding, Stringer Separation Plastic Bottom Slider Type DA DA DA Page 60 of 61 July 2014

Fastener Class (Chain Width: inch) Zipper Item Chain Width: inch) Chain Crosswise Strength Separating Unit Crosswise Strength Element Pull Off Strength Element Slippage Strength Slider Lock Holding Strength Zipper Requirements Page 4 of 4 5.7 (B) (0.180 0.310) 8.9 (0.310-0.390) 10 (0.320-0.500) 0.291 0.291 0.291 0.335 0.335 0.346 0.425 Brass Aluminum Plastic Brass Aluminum Plastic CEF kgf N lbs kgf N lbs kgf N lbs kgf N lbs kgf N lbs kgf N lbs kgf N lbs 65.0 637.0 143.3 40.0 392.0 88.2 50.0 490.0 110.3 80.0 784.0 176.4 50.0 490.0 110.3 60.0 588.0 132.3 100.0 980.0 220.5 15.0 147.0 33.1 15.0 147.0 33.1 17.0 166.6 37.5 22.0 215.6 48.5 22.0 215.6 48.5 22.0 215.6 48.5 22.0 215.6 48.5 8.5 83.3 18.7 5.5 53.9 12.1 8.0 78.4 17.6 11.0 107.8 24.3 7.5 73.5 16.5 9.0 88.2 19.8 - - - 6.0 58.8 13.2 5.5 53.9 12.1 7.0 68.6 15.4 8.5 83.3 18.7 7.5 73.5 16.5 10.0 98.0 22.1 - - - 7.0 68.6 15.4 7.0 68.6 15.4 6.0 58.8 13.2 7.0 68.6 15.4 7.0 68.6 15.4 7.0 68.6 15.4 7.0 68.6 15.4 Tab Pull Off (90 ) 25.0 245.0 55.1 25.0 245.0 55.1 20.0 196.0 44.1 30.0 294.0 66.2 30.0 294.0 66.2 30.0 294.0 66.2 30.0 294.0 66.2 Tab Twist Off 7.0 68.6 6.1 7.0 68.6 6.1 7.0 68.6 6.1 8.0 78.4 6.9 8.0 78.4 6.9 8.0 78.4 6.9 8.0 78.4 6.9 Operability 0.70 6.86 1.54 0.70 6.86 1.54 0.70 6.86 1.54 0.80 7.84 1.76 0.80 7.84 1.76 0.90 8.82 1.98 0.90 8.82 1.98 (open/close) Top Stop Holding Strength Bottom Stop Holding, Stringer Separation Plastic Bottom 15.0 147.0 33.1 15.0 147.0 33.1 15.0 147.0 33.1 18.0 176.4 39.7 18.0 176.4 39.7 18.0 176.4 39.7 18.0 176.4 39.7 12.0 117.6 26.5 12.0 117.6 26.5 14.0 137.2 30.9 15.0 147.0 33.1 15.0 147.0 33.1 17.0 166.6 37.5 18.0 176.4 39.7 Slider Type DA DA DA DA DA DA DA Methods: Chain Crosswise Strength ASTM D2061; 14.1 Separating Unit Crosswise Strength ASTM D2061; 30.3 Element Pull Off Strength ASTM D2061; 14.2 Element Slippage Strength ASTM D2061; 14.3 Slider Lock Holding Strength ASTM D2061; 87.1 Tab Pull Off (90 ) ASTM D2061; 68.1 Tab Twist Off ASTM D2061; 52.1 Operability (open/close) ASTM D2062; 16 Top Stop Holding Strength ASTM D2061; 22.2 Bottom Stop Holding, Stringer Separation ASTM D2061; 22.5 Note: 1 kgf=9.8n 1 kgf=2.206 lbs 1 cm=0.3937 inch Page 61 of 61 July 2014