VX279 Series LCD Monitor User Guide
First Edition August 2013 Copyright 2013 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ( ASUS ). Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners benefit, without intent to infringe. ii
Table of contents Notices... iv Safety information... v Care & Cleaning... vi Takeback Services... vii 1.1 Welcome!... 1-1 1.2 Package contents... 1-1 1.3 Monitor introduction... 1-2 1.3.1 Front view... 1-2 1.3.2 Back view... 1-4 1.3.3 QuickFit Function... 1-5 1.3.4 GamePlus Function... 1-6 2.1 Assembling the monitor base... 2-1 2.1.1 Assembling the base... 2-1 2.1.2 Detaching the base... 2-2 2.2 Adjusting the monitor... 2-3 2.3 Connecting the cables... 2-3 2.4 Turning on the monitor... 2-5 3.1 OSD (On-Screen Display) menu... 3-1 3.1.1 How to reconfigure... 3-1 3.1.2 OSD Function Introduction... 3-1 3.2 Specifications Summary... 3-5 3.3 Troubleshooting (FAQ)... 3-7 3.4 Supported operating modes... 3-8 iii
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. This product implements power management functionality. In case of no signal input after 10 seconds, the product automatically goes to sleep/ standby mode. As an Energy Star Partner, our company has determined that this product meets the Energy Star guidelines for energy efficiency. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003. iv
Safety information Before setting up the monitor, carefully read all the documentation that came with the package. To prevent fire or shock hazard, never expose the monitor to rain or moisture. Never try to open the monitor cabinet. The dangerous high voltages inside the monitor may result in serious physical injury. If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer. Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately. Slots and openings on the back or top of the cabinet are provided for ventilation. Do not block these slots. Never place this product near or over a radiator or heat source unless proper ventilation is provided. The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supply to your home, consult your dealer or local power company. Use the appropriate power plug which complies with your local power standard. Do not overload power strips and extention cords. Overloading can result in fire or electric shock. Avoid dust, humidity, and temperature extremes. Do not place the monitor in any area where it may become wet. Place the monitor on a stable surface. Unplug the unit during a lightning storm or if it will not be used for a long period of time. This will protect the monitor from damage due to power surges. Never push objects or spill liquid of any kind into the slots on the monitor cabinet. To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100-240V AC. If you encounter technical problems with the monitor, contact a qualified service technician or your retailer. This product contains chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. v
Care & Cleaning Before you lift or reposition your monitor, it is better to disconnect the cables and power cord. Follow the correct lifting techniques when positioning the monitor. When lifting or carrying the monitor, grasp the edges of the monitor. Do not lift the display by the stand or the cord. Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed with a cloth dampened with mild cleaner. Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended for use with the LCD. Never spray cleaner directly on the screen, as it may drip inside the monitor and cause an electric shock. The following symptoms are normal with the monitor: The screen may flicker during the initial use due to the nature of the fluorescent light. Turn off the Power Switch and turn it on again to make sure that the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use. When the same image is displayed for hours, an afterimage of the previous screen may remain after switching the image. The screen will recover slowly or you can turn off the Power Switch for hours. When the screen becomes black or flashes, or cannot work anymore, contact your dealer or service center to fix it. Do not repair the screen by yourself! Conventions used in this guide WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Information that you MUST follow to complete a task. NOTE: Tips and additional information to aid in completing a task. vi
Where to find more information Refer to the following sources for additional information and for product and software updates. 1. ASUS websites The ASUS websites worldwide provide updated information on ASUS hardware and software products. Refer to http://www.asus.com 2. Optional documentation Your product package may include optional documentation that may have been added by your dealer. These documents are not part of the standard package. Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for our customers to be able to responsibly recycle our products, batteries and other components as well as the packaging materials. Please go to http://csr.asus.com/english/takeback.htm for detail recycling information in different region. vii
1.1 Welcome! Thank you for purchasing the ASUS LCD monitor! The latest widescreen LCD monitor from ASUS provides a crisper, broader, and brighter display, plus a host of features that enhance your viewing experience. With these features, you can enjoy the convenience and delightful visual experience that the monitor brings to you! 1.2 Package contents Check your package for the following items: LCD monitor 1 x Adapter 1 x Power cable 1 x cable 1 x DVI cable (*depends on regions) 1 x DVI-HDMI cable (*depends on regions) 1 x HDMI cable (*depends on regions) 1 x MHL cable (*depends on regions) 1 x Audio cable (*depends on regions) 1 x Quick start guide 1 x Warranty card If any of the above items is damaged or missing, contact your retailer immediately. CAUTION ASUS LCD Monitor VX279 1-1
1.3 Monitor introduction 1.3.1 Front view VX279Q / H 4 6 7 VX279N 4 2 7 1. Button: Activates the QuickFit function. (Please refer to 1.3.3 QuickFit Function). 2. 3.,, Button: Press this hotkey to switch from six video preset modes (Scenery Mode, Standard Mode, Theater Mode, Game Mode, Night View Mode, and srgb Mode) with SPLENDID Video Intelligence Technology. Exit the OSD menu or go back to the previous menu as the OSD menu is active. Automatically adjusts the image to its optimized position, clock, and phase by pressing this button for 2~4 seconds (for mode only). / Button: Decreases values or moves your selection left/down. Volume hotkey (only available in VX279Q/H models) Contrast hotkey (only available in VX279N models) 1-2 Chapter 1: Product Introduction
4. MENU Button: Turns on the OSD menu. Enacts the selected OSD menu item. Press this button for 5 seconds to activate the Key Lock function. Press it again for 5 seconds to disactivate the function. 5. Button: Increases values or moves your selection right/up. Brightness hotkey 6. Input Select Button: Selects an available input source(only available in VX279Q/H models). Press (Input Select button) to display /HDMI/DisplayPort signals after you connect a, HDMI/MHL, or DisplayPort cable with the monitor. 7. Power Button/Power Indicator: Press this button to turn the monitor on/off. The color definition of the power indicator is as the table below. Status White Orange OFF Description ON Standby / Power saving OFF ASUS LCD Monitor VX279 1-3
HDMI / MHL-1 HDMI / MHL HDMI / MHL-2 DVI 1.3.2 Back view VX279Q HDMI / MHL 7 1 2 3 4 5 VX279H 6 HDMI / MHL-1 HDMI / MHL-2 4 VX279N 6 DVI 8 2 5 6 1. HDMI/MHL port: This port is for connection with an HDMI/MHL compatible device. 2. port: This 15-pin port is for PC connection. 3. Audio-in port: This port connects PC audio source by the bundled audio cable. 4. Earphone jack: This port connects to an earphone. 5. DC-in port: This port connects the adapter. 6. Kensington Lock: This port connects a lock-and-cable apparatus for security purposes. 7. DisplayPort: This port is for connection for a DisplayPort compatible device. 8. DVI port: This 24-pin port is for PC (Personal Computer) DVI-D digital signal connection. 1-4 Chapter 1: Product Introduction
EXIT EXIT QuickFit QuickFit EXIT QuickFit EXIT EXIT QuickFit QuickFit 1.3.3 QuickFit Function The QuickFit function allows users to have a preview of the document or photo layout directly on screen without printing test copies. QuickFit has three patterns: a. Grid pattern: Facilitates designers and users to organize content and layout on one page and achieve a consistent look and feel. Alignment Grid b. Paper size: Provides users to view their documents in real size on the screen. A4 Letter c. Photo size: Provides photographers and other users to accurately view and edit their photos in real size on the screen. 4x6 3x5 2x2 8x10 5x7 To activate QuickFit, press the QuickFit hotkey repeatedly to switch between different pattern sizes. When QuickFit is activated, press the control buttons to make adjustments. The QuickFit OSD displayed in the lower right corner of the screen will guide users to make selections. EXIT QuickFit EXIT QuickFit VX279H/Q VX279N ASUS LCD Monitor VX279 1-5
1.3.4 GamePlus Function VX279 The GamePlus Function provides a toolkit and creates a better gaming environment for users when playing different types of games. In addition, Aimpoint function is specially designed for new gamers or beginners who are interested in First Person Shooter (FPS) games. To activate GamePlus: 1. Press the MENU button to activate the OSD menu. 2. Press / and to select System Setup and press the MENU button to enter the System Setup sub-menu. 3. Press / and to select GamePlus and press the MENU button to enter its sub-menu. 4. Press / and to select ON and press the MENU button to enter its sub-menu. VX279 Splendid Color Image Input Select System Setup GamePlus ON OFF Move Menu Exit 5. Press / to select Aimpoint or Timer and press the MENU button to confirm the selection. 6. To exit the OSD menu, press the button. GamePlus Main Menu GamePlus - Aimpoint GamePlus Aimpoint Timer (Practice Mode) : Exit / Off : Select MENU : OK GamePlus - Timer : Exit / Off : Select MENU : OK GamePlus - Timer - Position Position : Exit / Off : Select MENU : OK : Exit / Off : Select MENU : OK To exit the GamePlus function, do one of the following: - Press the button. - Press the MENU button and select System Setup > GamePlus > OFF. 1-6 Chapter 1: Product Introduction
2.1 Assembling the monitor base 2.1.1 Assembling the base 1. Have the front of the monitor face down on a table. 2. Attach the base to the arm and fix with the screw to join them tightly. You can easily tighten the screw by fingers. 3. Adjust the monitor to the angle that is most comfortable for you. We recommend that you cover the table surface with soft cloth to prevent damage to the monitor. ASUS LCD Monitor VX279 2-1
2.1.2 Detaching the base 1. Disconnect power and signal cables. Carefully put the front of the monitor face down on a clean table. 2. Use your fingers to loosen the screw located at the bottom of the base, and remove the base from the stand. 3. Or, you may directly use a screwdriver to remove the screw that secures the base to the stand, and detach the base from the stand. We recommend that you cover the table surface with soft cloth to prevent damage to the monitor. Hold the base while removing the screw. 2-2 Chapter 2: Setup
HDMI / MHL-1 HDMI / MHL-2 2.2 Adjusting the monitor For optimal viewing, we recommend that you look at the full face of the monitor, then adjust the monitor to the angle that is most comfortable for you. Hold the stand to prevent the monitor from falling while changing its angle. You can adjust the monitor s angle from -5 to 20. -5 to +20 It is normal that the monitor slightly shakes while you adjust the viewing angle. 2.3 Connecting the cables VX279H Connect the cables according to the following instructions: HDMI / MHL-1 HDMI / MHL-2 HDMI / MHL Audio-in DC-IN Earphone jack ASUS LCD Monitor VX279 2-3
HDMI / MHL DVI VX279Q HDMI / MHL HDMI / MHL Audio-in DC-IN DisplayPort Earphone jack VX279N DVI DVI DC-IN To connect the power cord: a. Connect the adapter to the monitor's DC input. b. Connect one end of the power cable to the adapter, and the other end to a power outlet. To connect the /DVI, HDMI/MHL, or DisplayPort cable: a. Plug one end of the /DVI, HDMI/MHL, or DisplayPort cable to the monitor's /DVI, HDMI/MHL, or DisplayPort port. b. Connect the other end of the /DVI, HDMI/MHL, or DisplayPort cable to your computer's /DVI, HDMI/MHL, or DisplayPort port. c. Tighten the two screws to secure the or DVI connector. To connect the audio cable: connect one end of the audio cable to the monitor s Audio-in port, the other end to the computer s audio-out port. 2-4 Chapter 2: Setup
To use the earphone: a. When an HDMI/MHL or DisplayPort cable is connected, connect the end with plug type to the monitor s earphone jack. b. When /DVI and Audio-in-line is connected, connect the end with plug type to the monitor's earphone jack. When multiple video cable signals are connected, you can choose the desired input by pressing the Input Select key or select from the Input Select item in the OSD menu. HDMI port only available in VX279Q/H models. DVI port only available in VX279N models. DisplayPort only available in VX279Q models. 2.4 Turning on the monitor Press the power button. See 1.3.1 Front view for the location of the power button. The power indicator lights up in white to show that the monitor is ON. ASUS LCD Monitor VX279 2-5
3.1 OSD (On-Screen Display) menu 3.1.1 How to reconfigure VX279 1. Press the MENU button Splendid Scenery Mode to activate the OSD menu. Color Standard Mode Image Theater Mode 2. Press / and to Input Select Game Mode System Setup Night View Mode navigate through the functions. srgb Mode Highlight and activate the desired function by pressing the MENU Move Menu Exit button. If the function selected has a sub-menu, press / and again to navigate through the sub-menu functions. Highlight and activate the desired sub-menu function by pressing the MENU button. 3. Press / and to change the settings of the selected function. 4. To exit the OSD menu, press the button. Repeat step 2 and step 3 to adjust any other function. 3.1.2 OSD Function Introduction 1. Splendid VX279 This function contains six subfunctions that you can select for Splendid Scenery Mode Color Standard Mode Image Theater Mode your preference. Each mode has Input Select Game Mode System Setup Night View Mode the Reset selection, allowing you srgb Mode to maintain your setting or return to the preset mode. Move Menu Exit Scenery Mode: best choice for scenery photo display with SPLENDID Video Enhancement. Standard Mode: best choice for document editing with SPLENDID Video Enhancement. Theater Mode: best choice for movies with SPLENDID Video Enhancement. Game Mode: best choice for games playing with SPLENDID Video Enhancement. Night View Mode: best choice for dark-scene games or movies with SPLENDID Video Enhancement. srgb Mode: best choice for viewing photos and graphics from PCs. 3-1 Chapter 3: General Instruction
2. Color 3. Image In the Standard Mode, the Saturation, Skin Tone, Sharpness, and ASCR functions are not user-configurable. In the srgb Mode, the Brightness, Contrast, Saturation, Color Temp., Skin Tone, Sharpness, and ASCR functions are not userconfigurable. You can adjust Brightness, Contrast, Saturation, Color Temp., and Skin Tone from this menu. Brightness: the adjusting System Setup Skin Tone Smart View range is from 0 to 100. button is a hotkey to activate Move Menu Exit this function. Contrast: the adjusting range is from 0 to 100. Saturation: the adjusting range is from 0 to 100. Color Temp.: contains four modes including Cool, Normal, Warm and User Mode. Skin Tone: contains three color modes including Reddish, Natural, and Yellowish. SmartView: provides better display quality under big viewing angle. In the User Mode, colors of R (Red), G (Green), and B (Blue) are user-configurable; the adjusting range is from 0 ~ 100. You can adjust Sharpness, Aspect Control, Vivid Image, ASCR, Position ( only), and Focus ( only) from this menu. Sharpness: the adjusting range is from 0 to 100. Splendid Color Image Input Select Brightness 100 Contrast 80 Saturation 50 Color Temp. User Mode VividPixel: enhances the outline of the displayed picture and generates high-quality images on screen. ASCR: turns on/off the ASCR (ASUS Smart Contrast Ratio) function (only available in Scenery Mode, Theater Mode, Game Mode, and Night View Mode). Position: adjusts the horizontal postition (H-Position) and the vertical position (V-Position) of the image. The adjusting range is from 0 to 100 (only available for input). VX279 Splendid Color Image Input Select System Setup Move Menu Exit Natural OFF Sharpness 60 Trace Free Aspect Control VividPixel ASCR Position Aspect Control: adjust the aspect ratio to full, 4:3, 1:1 or OverScan VX279 4:3 is only available when input source is in 4:3 format OverScan is only available for the HDMI input source 60 Full 25 OFF 1/2 ASUS LCD Monitor VX279 3-2
Focus: reduces the Horizonal-line noise and Vertical-line noise of the image by adjusting (Phase) and (Clock) separately. The adjusting range is from 0 to 100. Phase adjusts the phase of the pixel clock signal. With a wrong phase adjustment, the screen shows horizontal distrubances. Clock (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the image i not proportional. 4. Input Select VX279 VX279 VX279 Splendid Splendid Splendid Color HDMI/MHL-1 Color HDMI/MHL Color DVI Image HDMI/MHL-2 Image DISPLAYPORT Image Input Select Input Select Input Select System Setup System Setup System Setup Move Menu Exit VX279H Move Menu Exit VX279Q Move Menu Exit VX279N In this menu, you can select your desired input source: - VX279H:, HDMI/MHL-1 or HDMI/MHL-2. - VX279Q:, HDMI/MHL or DISPLAYPORT. - VX279N:, or DVI. 5. System Setup VX279 Allows you to adjust the system. Splendid Splendid Demo Mode OFF Splendid Demo Mode: Color Volume 50 Image GamePlus splits the screen into two for Input Select ECO Mode OFF Splendid mode comparison System Setup OSD Setup Language English (only available in Scenery 1/2 Mode, Theater Mode, Game Move Menu Exit Mode, and Night View Mode). Volume: Adjust the earphone output volume level. The adjusting range is from 0 to 100. GamePlus: Activate the GamePlus function. ECO Mode: Activate the ecology mode for power saving. (Some gray levels may not be distinguished if ECO is ON. Its brightness is lower than that when setting the Contrast Ratio to 100.) OSD Setup: Adjust the horizontal postition (H-Position), vertical position (V-Position), OSD Timeout, DDD/CI, and Transparency of the OSD screen. 3-3 Chapter 3: General Instruction
Language: Select OSD language. The selections are English, French, German, Spanish, Italian, Dutch, Russian, Traditional Chinese, Simplified Chinese, and Japanese. Key Lock: Enable/Disable the Key Lock function. Information: Display the monitor information of Input Port, Resolution, H-freq., V-freq, and Model Name. All Reset: Set to Yes to revert all settings to the factory default status. ASUS LCD Monitor VX279 3-4
3.2 Specifications Summary Model Name VX279H VX279Q Panel Type TFT LCD Panel Size 27 (16:9, 68.6 cm) wide screen Max. Resolution 1920 x 1080 Brightness (Typ.) 250 cd/m 2 (Center 1 point, type) Contrast Ratio (Typ.) 1000:1 (Typical) ASUS Smart Contrast Ration (ASCR) 80,000,000:1 (with ASCR on) Color Saturation (NTSC) 72 % (Typ) Viewing Angle (H/V) CR>10 178 (H) / 178 (V) Display Colors 16.7 M colors (6 bits + Advanced-FRC) Response Time 5ms GTGσ Pixel Pitch 0.3114* (H) mm x 0.3114 (V) mm Full HD 1080P SPLENDID TM Video Enhancement Yes SPLENDID TM selection 6 video preset modes (by hotkey) Auto adjustment Yes (by hotkey) Color temperature selection 4 color temperatures Skin-Tone selection 3 skin tones VX279N Digital input HDMI/MHL (X2) HDMI/MHL, Displayport Analog input D-Sub Audio-in port 3.5 mm Mini-jack NA Earphone jack Yes NA Kensington Lock Slot Yes Auto Adjustment Hotkey Yes Brightness Adjustment Hotkey Yes Volume Adjustment Hotkey Yes NA Input Selection Hotkey Yes NA Contrast Adjustment Hotkey NA Yes Colors VX279H/Q/N VX279H-W/Q-W/N-W : Black White Speaker (Built-in) 1.5 W (x2) Power LED White (On) / Orange (Standby) Tilt -5 ~ +20 /DVI NA 3-5 Chapter 3: General Instruction
Model Name Voltage Rating (VX279H/Q) Voltage Rating(VX279N) Power Consumption(VX279H/Q) Power Consumption(VX279N) Temperature (Operating) Temperature (Non-operating) Dimensions (W x H x D) Weight (Esti.) Multi-languages Accessories Regulation approvals 65W Adaptor DC 19V 3.42A,100~240V at 50/60Hz 40W Adaptor DC 19V 2.10A,100~240V at 50/60Hz Power On: 46 W (max) Standby: < 0.5W at AC110V~ AC220V Power Off: < 0.5W at AC110V~ AC220V Power On: 32.5W (max) Standby: < 0.5W at AC110V~ AC220V Power Off: < 0.5W at AC110V~ AC220V 0 ~ 40 C -30 ~ 65 C VX279 H / Q / N 441.3 x 622.6 x 210.1 mm (monitor) 680.0 x 550.0 x 119.0 mm (package) 4.6 ± 1.0 kg (Net), 7.0 ± 1.0 kg (Gross) 21 languages (English, French, German, Spanish, Italian, Dutch, Russian, Poland, Czech, Croatia, Hungary, Romania, Portuguese, Turkey, Traditional Chinese, Simplified Chinese, Japanese, Korean Persian, Thai, Indonesian) Adapter, Power cable, cable, DVI cable, (*depends on regions ), DVI-HDMI cable (*depends on regions ), HDMI cable (*depends on regions ), MHL cable ( *depends on regions ), Audio cable (*depends on regions ), Quick Start Guide, Warranty card UL/cUL, CB, CE, FCC, CCC, BSMI, CU, c-tick, VCCI, Win 7 & 8 WHQL, EuP, RoHS, WEEE, EPEAT, HDMI, Energy Star 6.0, China Energy Label, J-Moss *Adaptor has PSE Regulation approvals. *Specifications subject to change without notice. ASUS LCD Monitor VX279 3-6
3.3 Troubleshooting (FAQ) Problem Possible Solution Power LED is not ON Press the button to check if the monitor is in the ON mode. Check if the adapter and power cable are properly connected to the monitor and the power outlet. The power LED lights amber and there is no screen image Screen image is too light or dark Check if the monitor and the computer are in the ON mode. Make sure the signal cable is properly connected the monitor and the computer. Inspect the signal cable and make sure none of the pins are bent. Connect the computer with another available monitor to check if the computer is properly working. Adjust the Contrast and Brightness settings via OSD. Screen image is not centered or Press the button for two seconds to sized properly automatically adjust the image. Adjust the H-Position or V-Position settings via OSD. Screen image bounces or a wave Make sure the signal cable is properly connected to pattern is present in the image the monitor and the computer. Move electrical devices that may cause electrical interference. Screen image has color defects Inspect the signal cable and make sure that none of (white does not look white) the pins are bent. Perform Reset via OSD. Adjust the R/G/B color settings or select the Color Temperature via OSD. Screen image is blurry or fuzzy Press the button for two seconds to automatically adjust the image (for mode only). Adjust the Phase and Clock settings via OSD. No sound or sound is low Make sure the audio cable is properly connected to the monitor. Adjust the volume settings of both your monitor and computer. Make sure the computer sound card driver is properly installed and activated. 3-7 Chapter 3: General Instruction
3.4 Supported operating modes Mode Resolution Refresh Rate Horizontal Frequency (KHz) Vertical Frequency (Hz) Pixel (MHz) DOS 720x400@70Hz 900x449 31.469 70.087 28.322 640x480@60Hz 800 x 525 31.469 59.940 25.175 640x480@72Hz 832 x 520 37.861 72.809 31.500 640x480@75Hz 840x500 37.500 75.000 31.500 800x600@56Hz 1024 x 625 35.156 56.250 36.000 S 800x600@60Hz 1056 x 628 37.879 60.317 40.000 800x600@72Hz 1040 x 666 48.077 72.188 50.000 800x600@75Hz 1056 x 625 46.875 75.000 49.500 1024x768@60Hz 1344x806 48.363 60.004 65.000 XGA 1024x768@70Hz 1328x806 56.476 70.069 75.000 1024x768@75Hz 1312x800 60.023 75.029 78.750 VESA 1152x864@75Hz 1600x900 67.5 75.000 108.00 1280x1024@60Hz 1688x1066 63.981 60.020 108.000 SXGA 1280x1024@75Hz 1688x1066 79.976 75.025 135.00 1280x960@60Hz 1800x1000 60.000 60.000 108.00 1280x800@60Hz 1680x831 49.702 59.810 83.500 1280x720@60Hz 1650x750 45.00 60.000 74.25 WXGA 1280x768@60Hz 1664x798 47.776 59.870 79.5 1360x768@60Hz 1792x795 47.712 60.015 85.500 1366x768@60Hz 1792x798 47.712 59.790 85.500 WXGA+ 1440x900@60Hz 1904x934 55.935 59.887 106.500 UXGA 1600x1200@60Hz 2160x1250 75.000 60.000 162.000 WSXGA+ 1680x1050@60Hz 2240x1089 65.290 59.954 146.250 WUXGA 1920x1080@60Hz 2200x1125 67.500 60.000 148.500 1920x1080@60Hz 2080x1111 66.587 59.934 138.500 MAC 640x480@66.66Hz 864x525 35 66.66 30.24 S 832x624@75Hz 1152x667 49.714 74.533 57.27 * Modes not listed in the table may not be supported. For optimal resolution, we recommend that you choose a mode listed in the table above. * This monitor supports full HD (480p, 576p, 720p, 1080i/p) video content from game consoles, DVD players and other consumer video devices via HDMI. ASUS LCD Monitor VX279 3-8