Plastic pipe clamp CLIC 8 64 Technical data sheet 1/2015 1 1. Product description The most efficient mounting system for pipes, cables and many other applications. Diameter dimensions ranging from 8 to 64 mm for the indoor area. 2. Application areas Electrical instaation of a kinds in the indoor area Instaation technology Instaations within the chemical industry Sanitary instaations / hot and cold water pipes 3. Features One-piece, self locking plastic pipe clamp Tool-free instaation system Very high dynamic load and stress corrosion crack stability Very low moisture absorption Chloride- and weather UV (for the exterior) Wide range of mounting temperature from -25 C to +90 C Mounting with metrical or wood screws Approved by: KIWA, UL (1565/2043) 100 % made in Switzerland 4. Material data Material quality Polymerblend Density at +20 C 1.21 g/cm 3 Elongation at yield 5 % E-Modulus in tension 2100 MPa Water absorption at 23 C 0.50 % Moisture absorption (23 C / 50 % r.f.) 0.15 %
TDS Plastic pipe clamp CLIC 8 64 1/2015 2 4. Material data (cont.) Dielectric strength 32 kv/mm Weather proof 25 C up to +90 C Maximum service temperature short term +120 C Maximum service temperature long term +90 C Flammability HB according to UL 94 Impact value (Charpy, +23 C) 56 kj/m 2 Impact value (Charpy, 30 C) 29 kj/m 2 Halogen halogen free as per IEC 754-2 Petrol, diesel, oil Corrosion Chloride salt UV stabilized as per ISO 4892-2 Standard colours light grey (similar to RAL 7035) 5. Technical data Type Clamping range [mm] A [mm] B [mm] C [mm] D [mm] E [mm] F [mm] H* Breaking load [N] min. max. wood [mm] metric Fy/Fx** 8 7.8 9.5 17.1 17.5 26.4 17.1 14.5 7.5 3.5 M6 450 10 9.5 11.8 17.1 17.5 26.2 17.1 14.5 7.5 3.5 M6 470 12 11.8 14.3 20.2 19.5 28.3 17.2 14.5 7.5 3.5 M6 500 15 14.3 16.8 20.6 18.8 32.0 17.1 14.5 7.5 3.5 M6 650 17 16.8 19.5 22.5 23.7 35.4 19.5 16.0 7.8 4.5 M6 700 20 19.5 21.8 24.8 24.9 39.4 20.0 16.3 7.8 4.5 M6 750 22 21.8 24.8 27.8 26.0 42.0 20.0 16.5 7.8 4.5 M6 800 25 24.8 27.8 30.4 28.0 45.1 20.0 17.0 8.8 4.5 M6 900 28 27.8 31.2 33.4 31.7 48.9 20.2 17.0 8.8 4.5 M6 950 32 31.2 35.5 38.0 34.5 54.4 21.0 17.5 9.0 4.5 M6 / M8 1100 36 35.5 39.5 41.8 36.5 59.4 21.0 18.0 9.1 4.5 M6 / M8 1200 40 39.5 43.5 46.2 38.2 64.2 21.0 18.6 9.4 4.5 M6 / M8 1350 47 46.5 50.5 53.5 43.0 72.8 22.0 19.5 9.8 4.5 M6 / M8 1400 51 50.5 55.5 58.6 46.8 78.7 23.0 20.0 10.2 4.5 M6 / M8 1500 59 58.5 64.0 66.3 52.0 88.2 23.2 21.0 10.7 4.5 M6 / M8 1600 * H = screw diameter; wood screw (wood) / metal screw (metric) ** with screw DIN 96 at +20 C, safety factor must be considered! Fy Fx Bottom view CLIC flange M6 CLIC flange M8
TDS Plastic pipe clamp CLIC 8 64 1/2015 3 6. Selection guide Type Steel pipe Copper pipe Cast iron pipe PE pipe PVC pipe Cable-ducts Coaxial cable Certification Breaking load [N] mm inch mm mm mm mm metric measures M inch Kiwa UL Fy/Fx* 8 8 450 10 10 10 470 12 13.5 ¼" 12 12 500 15 15 16 16 ½" 650 17 17.2 ⅜" 18 700 20 21.3 ½" 20 20 ⅝" 750 22 22 800 25 26.9 ¾" 25 25 900 28 28 ⅞" 950 32 33.7 1" 35 32 32 32 1100 36 1 ¼" 1200 40 42.4 1 ¼" 42 40 40 1350 47 48.3 1 ½" 48 50 50 50 1 ⅝" 1400 51 54 1500 59 60.3 2" 64 63 1600 * with screw DIN 96 at +20 C, safety factor must be considered! 7. Chemical resistance Acetic acid 5 % Acetone Acetylene Ammonia liquid Benzine Brake fluid l Butane Butanol Butyl acetate Carbon monoxide Carbon tetrachloride Carbonic acide Caustic potash 10 % Chlorbenzene Chlorine gas Chloroform Citric acid 10 % Decalin Dibutylphthalate Diesel fuel l Dimethyl formamide Dimethylether Dioctylphthalate Dioxan l Engine oil l Ethanol Ethyl acetate Ethyl ether l Ethylene oxide Fatty acide Fatty alcohol Formic acide 10 % l Glycerine Glycol Glysantine l Heating oil Heptane, Hexane Hydraulic oil Hydrochloric acid 10 % Hydrogen fluoride Inert gas Iso-octane l Isopropanol Ketone aliphatic Lacquer Methanol Methyene chloride Mineral oil Naphaline Nitric acid 10 % Nitrohydrochloric acid Oleum Ozone Paraffin Perchloric acid Petroleum ether Phosphoric acid 10 % Potassium hypochlorite l Silicon oils Sodium hydroxide 10 % Soldering water Styrol Sulphuric acid 10 % Tetradydrofurene Toluene Transmission oil Trichlorethane Trychlorethylene Turpentine Turpentine oilreplacem. Xylene limited resistance not
TDS Plastic pipe clamp CLIC 8 64 1/2015 8. Instaation/mounting Simply mount CLIC, push pipe in by hand, grips and locks by applying slight pressure. To open: unlock the CLIC latch with screwdriver. Examples of concrete base-materials wood screew, TILCA anchor bolt, CLIC flange or TILCA fire resisting anchor, CLIC flange or TILCA nail plug, CLIC flange TILCA fire resisting anchor, CLIC flange Examples of brickwork base-materials or TILCA nail plug 9. Testings/authorizations/specifications/compliance KIWA UL REACH, RoH 10. Safety data sheet not required 4
TDS Plastic pipe clamp CLIC 8 64 1/2015 5 11. Manufacturer/brand/production Gotthardstrasse 6 Post Box 2265 8022 Zurich Switzerland CLIC is a registered international trademark of Egli Fischer and is 100 % Swiss made. The CLIC technology is protected by Swiss and international patents held by Egli Fischer. 12. Accessories Further accessories, e.g. spacers, base plates for multiple mountings, are available at the EF Shop (online) or are listed in the EF catalogue (print or PDF). 13. Links/downloads For further information: EF Shop EF Website CLIC-Website http://shop.efco.ch http://www.efco.ch http://www.clic-original.com The recommendations and data given are based on our experience to date and are standard values. No liability can be assumed in connection with their usage and processing. In individual cases the chemical resistance has to be verified by your own testings. For further technical information please refer to Egli Fischer.