DET NORSKE VERITAS TYPE APPROVAL CERTIFICATE CERTIFICATE NO. P-13405 This Certificate consists of 5 pages This is to certify that the Pipe System with Couplings with type designation(s) Mapress Copper;Mapress Cunife Manufactured by Geberit Mapress GmbH LANGENFELD RHEINLAND, Germany is found to comply with Det Norske Veritas' Rules for Classification of Ships Offshore Standard DNV-OS-D101, Marine and Machinery Systems and Equipment Det Norske Veritas' Standards for Certification 2.9 No. 5-792.20 Application The application of the piping systems and couplings is depending upon the type, and only for Class III piping systems, see certificate. Type: Temperature range: Max. pressure: Design: Mapress Copper -20 to 120 C 10-16 bar (dep. size, see cert.) pressfitting Mapress Copper -20 to 120 C 10-16 bar (dep. size, see cert.) pressfitting Place and date This Certificate is valid until Høvik, 2010-02-19 2013-12-31 for DET NORSKE VERITAS AS Helge Drange Local Office Øyvind Skåra Head of Section DNV Essen Surveyor Notice: This Certificate is subject to terms and conditions overleaf. Any significant change in design or construction may render this Certificate invalid. The validity date relates to the Type Approval Certificate and not to the approval of equipment/systems installed. If any person suffers loss or damage which is proved to have been caused by any negligent act or omission of Det Norske Veritas, then Det Norske Veritas shall pay compensation to such person for his proved direct loss or damage. However, the compensation shall not exceed an amount equal to ten times the fee charged for the service in question, provided that the maximum compensation shall never exceed USD 2 million.in this provision Det Norske Veritas shall mean the Foundation Det Norske Veritas as well as all its subsidiaries, directors, officers, employees, agents and any other acting on behalf of Det Norske Veritas. DET NORSKE VERITAS AS VERITASVEIEN 1, 1322 HØVIK, NORWAY TEL: (+47) 67 57 99 00 FA: (+47) 67 57 99 11 Form No.: 20.90a Issue: January 98 Page 1 of 5
Product description Press fittings with o-ring seal Material: Type Fitting O-ring Mapress Copper Mapress Cunife Copper WNo. 2.0090 acc. DIN EN 1057 and WNo. 2.1096.01 acc. DIN 1705 CuNi10Fe1.6Mn (WNo. 2.1972.11) acc. DIN 86019 Butyl+FPM/FKM Fitting types: Product Description Mapress Copper Mapress Cunife Sleeve, straight, short Sleeve, straight, long Reducer Elbow Elbow, one plain end transition, plain ends Elbow, plain ends 75 adaptor, male threads, one end adaptor, female threads, one end tap connector Adaptor, male threads, one end Adaptor, female threads, one end Adaptor, with union nut Adaptor union, with male threads Adaptor union, with female threads Adaptor, male threads one end, one plain end DET NORSKE VERITAS AS VERITASVEIEN 1, 1322 HØVIK, NORWAY TEL: (+47) 67 57 99 00 FA: (+47) 67 57 99 11 Form No.: 20.90a Issue: January 98 Page 2 of 5
Adaptor, female threads one end, one plain end adaptor union with female threads adaptors with wall plate, female threads Tee Tee, reduced Tee, outlet with female threads Pipe cross Pipe cross End cap Radiator connectors Flange PN 6 Flange PN 10/16 Collar for loose flange, PN 6 Collar for loose flange, PN 10/16 Deck- and bulkhead penetration Application/Limitation The couplings may be used in the following systems: Mapress Copper: domestic fresh- and potable water and air-conditioning systems (media: condensed water and water with ethylene glycol) and non essential systems Mapress Cunife: Sea water, fire main and water spray, foam and sprinkler systems, ballast systems, fresh- and seawater cooling systems, tank cleaning service, bilge, non essential systems, compressed air, service air, inert gas, flammable luquids. Maximum working pressure: DN Mapress Cunife Mapress Copper Pressing tool 10 NA 12 13 bar 15 NA 20 25 32 40 50 65 80 100 13 bar 16 bar 12 bar 10 bar 10 bar NA Jaw Collar DET NORSKE VERITAS AS VERITASVEIEN 1, 1322 HØVIK, NORWAY TEL: (+47) 67 57 99 00 FA: (+47) 67 57 99 11 Form No.: 20.90a Issue: January 98 Page 3 of 5
The fittings are to be used with pipes of the following minimum dimensions: DN Mapress Copper/Cunife 10 12 15 20 25 32 40 50 65 80 1.0 mm 1.5 mm 2.0 mm 100 Copper pipes according to EN 1057 and DVGW GW 392 The piping system can not be used: - through ballast or fuel oil tanks - as air, overflow and sounding pipes for structural tanks - in locations where it might be subject to heavy and/or double sided corrosion Pipe penetrations through watertight bulkheads or fire bulkheads or decks shall be approved in each separate case. The components are to be mounted according to manufacturer's instructions. Type Approval documentation Tests carried out Mapress Copper: Burst- and vacuum tests Mapress Cunife: Assembly-, Leakage-, Vacuum-, Pullout-, Pressure pulsation and vibration-, fire- and burst pressure tests Marking of product For traceability with this type approval, each fitting is at least to be marked with: - Manufacturers name or trademark - Size DET NORSKE VERITAS AS VERITASVEIEN 1, 1322 HØVIK, NORWAY TEL: (+47) 67 57 99 00 FA: (+47) 67 57 99 11 Form No.: 20.90a Issue: January 98 Page 4 of 5
Certificate retention survey For retention of the Type Approval, a DNV Surveyor shall perform a survey - every second year and before the expiry date of this certificate - to verify that the conditions for the type approval are complied with and to witness burst testing on samples of fittings selected at random from stock or from the running production. END OF CERTIFICATE DET NORSKE VERITAS AS VERITASVEIEN 1, 1322 HØVIK, NORWAY TEL: (+47) 67 57 99 00 FA: (+47) 67 57 99 11 Form No.: 20.90a Issue: January 98 Page 5 of 5