VID-ALARM-8CH-COM Reference Manual Please read these instructions and keep for later reference. NOTES: 1. Do not use in extreme heat or cold temperatures. 2. Do not expose to rain or moisture 3. Do not expose to flammable, explosive, or corrosive gas. 4. Avoid exposure to dust or other particles that may get inside the equipment. 5. Use of extension cords may significantly increase risk of fire, electric shock, and damage to the equipment. 6. To avoid risk of electric shock and damage to equipment do not open the device. 7. Professional installation is required.
VID ALARM 8CH COM Reference Manual 2 Additional Items Included A B C a. 9 Pin DIN Female to Female Serial Adapter b. Terminating Resisters c. Phoenix Type Connectors (1x4Screw/4x8Screw) d. Power Adapter D Back Panel Front Panel Brief Introduction Alarm in: 8 port Normal Open / Normal Close Input Voltage 0 ~ +15V Alarm out: 8 port Normal Open / Normal Close connector Power Supply: 12 VDC 10 W Output Power: 10 A at 28 VDC or 7 A at 220 VAC Communication type: RS485, RS232 Working temperature: 10 degree C 70 degree C (inside)
VID ALARM 8CH COM Reference Manual 3 1.General The DV7608 alarm box is a 8 channel alarm inputs, 8 channel controllable normally open relay outputs alarm box, connected with digital video recorder to conduct single or full arm, disarm, enquiry and switch controlling function. 2.Main Features 8 channel alarm inputs, 8 channel relay outputs (NO) Alarm linkage function Watchdog function, auto reset function in strong reference environment. Open circuit and short circuit arm function Provide protocol, 16 ID setting, connect up to 128 alarm probes at maximum. 3.Specification Power Supply Power output Auxiliary relay Communication Protocol Operating Environment DC13.5V DC12V/400mA 8 normally open relay, AC220V/2A RS485, RS232 Multi protocol setting upon requirement, such as DCTRLS, W110, RM110, SE600, etc. 10 ~70 indoor 4. Connection Diagram
VID ALARM 8CH COM Reference Manual 4 5.Board LED Indication Alarm out LED, light means relay closed, off means relay open Alarm in LED, long light means in arm setup status, blinking means arming Communication LED, LED blinks when the communication mode is in accordance with the host computer protocol. 6.Connection Operate as following figure to connect alarm probe,and connect a resistance(2k)in series connection at NO contact. S=signal, =ground wire 7.Protocol setting You will see J1&j2 on the board as you open the box (the number1 means open circuit, number 0 means short circuit) No. Protocol J1 J2 Note 0 DCTRLS 0 0 Setting from address 0 1 RM110 0 1 2 W110 1 0 3 SE600 1 1 The address of channel 1~8 is 0,channel 9~16 is 1
VID ALARM 8CH COM Reference Manual 5 8.Setting the alarm box ID The alarm box ID number is set by setting the 1 4 bits of DIPswitch. Detailed setting please refers to the table below. The number 1 means the DIP switch setting should be ON, and the number 0 means OFF. Note: the ID number is binary digit ID Switch number 1 2 3 4 0 0 0 0 0 1 0 0 0 1 2 0 0 1 0 3 0 0 1 1 4 0 1 0 0 5 0 1 0 1 6 0 1 1 0 7 0 1 1 1 8 1 0 0 0 9 1 0 0 1 10 1 0 1 0 11 1 0 1 1 12 1 1 0 0 13 1 1 0 1 14 1 1 1 0 15 1 1 1 1
VID ALARM 8CH COM Reference Manual 6 PROTOCOL Control code, which send out from DVR Command format: 9600,N, 8,1 NO. Function Data1 Data2 Data3 Data4 Data5 Data6 Format Start bit ID Command Parameter1 Parameter 2 Check sum Note 1 Alarm state enquiry E0 00 0F 3F 00 00 2 Relay state enquiry E0 00 0F 3B 00 00 3 Output ON/OFF E0 00 0F 3D B0 B7 B8 B15 Bits (0 15) is the relay control bits of 1 16 channel, 1=ON, 0=OFF Data send back No. Function Data1 Data2 Data3 Data4 Data5 Note 1 Alarm state send back 2 Relay state send back F0 00 0F D0 A0 A7 A8 A15 A (0 15) is corresponding to alarm inputs 1 16,1=alarm, 0=dis alarm F0 00 0F D2 A0 A7 A8 A15 A (0 15) is corresponding to outputs 1 16,1=ON, 0=OFF Note: 1.The data4&data5 of this alarm box is 0 NOTES:
VID ALARM 8CH COM Reference Manual 7 Technical Support For difficulties using this unit please contact Aventura technical support at 631 300 4000 or toll free at 1 877 707 9600. Online support is available at www.aventuracctv.com or email techsupport@ati247.com When contacting technical support be certain to have full details about your Aventura products available, including model and invoice numbers. Service Any service required by this unit should be performed by Aventura or authorized service personnel. Unauthorized service may invalidate warranties or service agreements. Some service may require equipment to be returned to Aventura s offices for evaluation and repair. Be certain to follow proper packing and shipping instructions for all equipment to prevent damage during transport.