17865 1. Product and Company Identification Product Name: Product Code: Application: Supplier: Emergency Telephone: 2. Composition/Information on Ingredients This chemical product is a preparation. Anti-Gel & Performance Improver See Attachment Diesel fuel additive Ford Motor Company Attention: MSDS Information, P.O. Box 18 Dearborn, Michigan 48121 1-800-32-3673 Poison Control Center: 1-800-5-3673 CHEMTREC: U.S. and Canada: 1-800-424-300 CHEMTREC: International: 1-703-527-3887 Chemical Name CAS Number Percent Concentration HYDROTREATED LIGHT DISTILLATE (PETROLEUM) NAPHTHA (PETROLEUM), HEAVY AROMATIC NAPHTHALENE 1,2,4-TRIMETHYLBENZENE 64742-47-8 64742-4-5 1-20-3 5-63-6 60-100 1-5 0.1-1 0.1-1 Hazard Classification HAZCOM HAZCOM IARC 2B (NA) NTP (SUSP) PEL/TLV-US RSMS_D_ALL SARA 313 CAA-HAP ACGIH/OSHA RQ RSMS_D_ALL WHMIS 0.1 3. Hazards Identification WARNING Health: Physical and Chemical Hazards: Environment: This product may cause irritation to the eyes and skin. This product is irritating to the respiratory system. Exposure to oil mist/fume/vapor may cause respiratory tract irritation. Aspiration hazard if swallowed; can enter lungs and cause damage. Prolonged or repeated contact with this product may dry and/or defat the skin. Combustible liquid. Material contains a chemical which is a Hazardous Air Pollutant (HAP), regulated by the United States Clean Air Act. Page: 1 /
4. First-Aid Measures Inhalation: Skin Contact: Eye Contact: Ingestion: Notes to a Physician: 17865 If gas/fume/vapor/dust/mist from the material is inhaled, remove the affected person immediately to fresh air. If irritation persists, get medical attention. Immediately take off all contaminated clothing. For skin contact, wash immediately with soap and water. If irritation persists, get medical attention. In case of contact with eyes, rinse immediately with plenty of water for at least 15 minutes and seek medical attention. If irritation persists, get medical attention. If the material is swallowed, get immediate medical attention or advice -- Do not induce vomiting. If the affected person is not breathing, apply artificial respiration. If the affected person's breathing is difficult, give oxygen. This material, if aspirated into the lungs, may cause chemical pneumonitis; treat the affected person appropriately. 5. Fire-Fighting Measures Extinguishing Media: Specific Methods: Specific Hazards: Protection of Firefighters: Dry chemical, foam, carbon dioxide, water fog. Use water to cool fire-exposed containers, structures, and to protect personnel. Water may be used to cool exposed containers to prevent pressure build-up and explosion when exposed to extreme heat. Vapors emitted may form a flammable mixture with air. Vapors are heavier than air and may travel along the ground to some distant source of ignition and flash back. Water or foam may cause frothing if the product is heated above 3 degrees C (200 degrees F). Empty containers may retain product residue including Flammable or Explosive vapors. Do not cut, drill, grind, or weld near full, partially full, or empty product containers. Upon decomposition, this product emits carbon monoxide, carbon dioxide and/or low molecular weight hydrocarbons. Fire fighters should be equipped with NIOSH-approved, self-contained breathing apparatus (SCBA) and full protective clothing. Page: 2 /
17865 6. Accidental Release Measures Personal Precautions: Environmental Precautions: Methods for Cleaning Up: Avoid inhalation of vapors and contact with skin and eyes. Do not smoke or use open fire or other sources of ignition. Eliminate all sources of ignition or flammables that may come into contact with a spill of this material. Ventilate the contaminated area. Wear appropriate protective equipment and clothing during clean-up. Do not allow the spilled product to enter public drainage system or open water courses. Do not allow this material to drain into sewers/water supplies. Contain the discharged material. Absorb the spilled material with an inert absorbent (nonflammable) material. 7. Handling and Storage Handling: Technical Measures: Precautions and Advice for Safe Handling: Keep this product from heat, sparks, or open flame. Avoid breathing vapor, mist or gas. Avoid contact with skin, eyes and clothing. Avoid prolonged or repeated skin contact with this material. Keep away from heat, spark and open flame. Storage: Do not store at temperatures above 120 F (4 C) Technical Measures: Storage Conditions: No special precautions necessary. Ground all containers of this material. Store in a cool, well-ventilated area away from sources of heat. Store this product away from strong oxidizing agents. Page: 3 /
17865 8. Exposure Controls/Personal Protection Engineering Measures: Control Parameters: General (mechanical) room ventilation is expected to be satisfactory if handled at low temperatures or in covered equipment. Local ventilation is needed in the presence of airborne mists. If oil mist is generated, observe the OSHA exposure limit of 5 mg/m3. Ford Motor Company recommends an exposure limit of 1.0 mg/m3. Exposure Limits: Chemical Name TWA STEL/C References NAPHTHALENE 10(ppm) 15(ppm) ACGIH 10(ppm) 50(ppm) OSHA Personal Protective Equipment: Respiratory Protection: Hand Protection: Eye Protection: Skin and Body Protection: Hygiene Measures: If engineering controls do not maintain airborne concentrations to a level which is adequate to protect worker health, an approved respirator must be worn. Respirator selection, use and maintenance should be in accordance with the requirements of OSHA Respiratory Protection Standard 2 CFR 110.134 and/or Canadian Standard CSA Z4.4. Use of impervious gloves is recommended, such as neoprene. Wear chemical goggles; face shield (if splashing is possible). Remove contaminated clothing and wash before reuse. Use good personal hygiene. When using this material, do not eat, drink or smoke. Page: 4 /
17865. Physical and Chemical Properties Specific Gravity: Physical State: Odor: Color: ph: Temperature Range During which Changes in Physical State Occur: Flash Point: Explosion Properties: LEL: Vapor Pressure: Solubility: Viscosity: Evaporation Rate: Boiling Point: UEL: 0.82 LIQUID SOLVENT AMBER N.AP 182.2 C 66 C ASTM D56 6 % 0.7 % 0.1@20 C mmhg NEGLIGIBLE IN WATER 2-4@40 C cst ASTM D445 N.AP 10. Stability and Reactivity Stability: Conditions and Materials to Avoid: Hazardous Decomposition Products: This is a stable material. Hazardous polymerization will not occur. This product may react with strong oxidizing agents (bleach--sodium hypochlorite, calcium hypochlorite, hydrogen peroxide, permanganate, nitric acid, concentrated OXYGEN, perchlorates). Carbon monoxide, carbon dioxide, and other low molecular weight hydrocarbons. Page: 5 /
17865 11. Toxicological Information Inhalation: Skin Contact: Chronic (Long Term) Toxicity: Exposure to oil mist/fume/vapor may cause respiratory tract irritation. Prolonged and/or repeated skin contact with this product may cause irritation/dermatitis. Base oil severely refined: Not carcinogenic in animal studies. Representative material passes IP-346, Modified Ames test, and/or other screening tests. This material contains an ingredient which is a cancer hazard based on tests with laboratory animals. Overexposure may create a cancer risk. This product contains naphthalene. A U.S. National Toxicology Program (NTP) report states that a lifetime inhalation exposure to naphthalene resulted in increases in tumors of the nose in rats. In a previous U.S. NTP study, lifetime inhalation exposure to naphthalene increased lung tumors in female mice. The relevance of the rodent findings to humans is questionable. 12. Ecological Information No specific aquatic data available for this product. 13. Disposal Considerations Waste from Residues: Contaminated Packaging: Dispose of waste material according to Local, State, Federal, and Provincial Environmental Regulation. Empty containers may contain hazardous residues (vapors, liquid, and/or solid). Do not reuse the empty container without commercial cleaning or reconditioning. No consideration given when disposed of according to local, state, and Federal regulations. Page: 6 /
14. Transport Information 17865 U.S. Department of Transportation (DOT) 4 - CFR 172.101 Canadian Transportation of Dangerous Goods (T.D.G.) - TDGR Schedule II Secretary of Communication and Transportation (SCT) - NOM-002-SCT2/14 (Mexico) International and Domestic Air Transportation - ICAO & IATA Section 4.2 International Water Transportation - IMDG Code Amendment 31-02 15. Regulatory Information California Proposition 65: WARNING: This product contains a chemical known to the State of California to cause cancer. This product contains a toxic chemical or chemicals subject to the reporting requirements of Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 186 and 40 CFR Part 372. Material contains a chemical which is a Ford Motor Company Material of Concern. Use and release of this material should be minimized to the greatest extent possible. 16. Other Information Key/Legend: N.AP = Not applicable; N.AV = Not available; ND = Not determined or No data; TLV = Threshold limit value; TWA = Time-weighted average; STEL = Short-term exposure limit; C = Ceiling limit HMIS and NFPA Hazard Class Information: HMIS Hazard Class: NFPA Hazard Class: Health: 2 (Moderate) Flammability: 2 (Moderate) Physical Hazard: 0 (Least) Health: 2 (Moderate) Flammability: 2 (Moderate) Instability: 0 (Least) The following sections contain revisions OR NEW statements. Preparation Information: 2 16 The chemical identification and properties for this material were provided by the manufacturer. For Canadian locations, a manufacture's MSDS is available upon request. Health and safety information has been evaluated by the Occupational and Environmental Health Sciences Department, Ford Motor Company, Diagnostic Service Center II, 1800 Fairlane Drive, Allen Park, MI 48101, USA. Page: 7 /
Disclaimer: 17865 The information on this data sheet represents our current data and is accurate to the best of our knowledge as to the proper handling of this product under normal conditions and in accordance with the application specified on the packaging and/or technical guidance literature. Any other use of the product which involves using the product in combination with any other product or any other process is the responsibility of the user. Page: 8 /
17865 Attachment Product Code Container Size Part of Kit Kit Product Code PM-23-A PM-23-ASU PM-23-GAL 20 fl. oz. (51 ml) 6 fl. oz. (177 ml) 1 U.S. gal. (3.78 L) Page: /