USB-IF Product Order Form Please use the following information to select the test hardware from the USB-IF estore. USB 3.1 (10 GT/s) Type-C Electrical Test Fixture Kit The USB 3.1 USB (10 GT/s) Type-C Electrical Test Fixture Kit provides a worst case, ISI hardware channel for PHY s. It is intended to assist companies in testing transmitter signal quality and receiver sensitivity for either hosts or peripherals. The current kit contains sixteen test fixtures, 1 meter Type-C to cable, 2 meter Type-C cable, one 5 Volt DC power supply. Due to high demand each company is allowed a maximum order of two (2) kits at this time. Please use product code USB31CET to order. Member Price: $2400.00 Non-Member Price: $2900.00 USB 3.1 (10 GT/s) Type-A and Micro-B Electrical Test Fixture Kit The USB 3.1 (10 GT/s) USB Type-A and Micro-B Electrical Test Fixture Kit provides a worst case, ISI hardware channel for PHY s. It is intended to assist companies in testing transmitter signal quality and receiver sensitivity for either hosts or peripherals. The kit contains fifteen test fixtures, 1 meter Standard-A to Micro-B cable, one 5 Volt DC power supply to provide V-Bus to peripherals, and a jumper (for two pin header). Due to high demand each company is allowed a maximum order of two (2) kits at this time. Please use product code USB31AET to order. Member Price: $1800.00 Non-Member Price: $2200.00 Low-speed Functional Compliance Test Device The LS Functional Compliance Test Device is used by high-speed hub vendors to validate transaction translators. Please use product code USBLSTD to order. Member Price: $90.00 Non-Member Price: $110.00 Full-speed Functional Compliance Test Device The FS Functional Compliance Test Device is used by high-speed hub vendors to validate transaction translators. Please use product code USBFSTD to order. Member Price: $250.00 Non-Member Price: $300.00 USB 3.0 Electrical Test Fixture Kit - OUT OF STOCK The USB 3.0 Electrical Test Fixture Kit provides a worst case, ISI hardware channel for PHY s. It is intended to assist companies in testing transmitter signal quality and receiver sensitivity for either hosts or peripherals. This kit ships with the necessary cables to be used in conjunction with the fixtures. Please use product code USB3ET to order. Member Price: $700.00 Non-Member Price: $950.00 USB 2.0 Hi-Speed Signal Quality Test Fixture Set The USB 2.0 Hi-Speed Signal Quality Test Fixtures are used for testing signal quality of hi-speed hosts and peripherals. The fixtures eliminate the need for probes and require quality SMA cables for direct connection to the scope. The fixtures include USB cables but do not include SMA cables. Please use product code USB2SIGQUAL to order. Member Price: $650.00 Non-Member Price: $900.00 Page 1 of 6
Product Order Form Please email the completed order form including payment information to admin@usb.org. You may also fax or mail your completed order form. USB Implementers Forum 3855 SW 153rd Drive Beaverton, OR 97003 USA Tel: 503-619-0426 Fax: 503-644-6708 The following table is for use by Members of the USB Implementers Forum only: Product Code: Description: Quantity: Members Unit USB31CET USB 3.1 USB (10 GT/s) Type-C Electrical Test Fixture Kit $2400.00 USD Extended Price: USB31AET USB 3.1 USB (10 GT/s) Type-A and Micro-B Electrical Test Fixture Kit $1800.00 USD USBLSTD Low Speed Functional Compliance Test Device $90.00 USD USBFSTD Full Speed Functional Compliance Test Device $250.00 USD USB3ET USB 3.0 Electrical Test Fixture Kit OUT OF STOCK $700.00 USD OUT OF STOCK USB2SIGQUAL USB 2.0 Hi-Speed Signal Quality Test Fixture Set $650.00 USD Total Payment Due: Shipping and Handling Fees are included in the prices above. Duties, customs and other taxes are not included within the above prices. You should receive an invoice from the carrier and/or customs for any additional expense incurred. It is your responsibility, and not that of USB-IF, to pay these taxes. See next page for Non-Member pricing. ALL PRODUCTS AND DOCUMENTS OFFERED FOR SALE BY USB-IF ARE PROVIDED "AS IS" AND WITHOUT ANY WARRANTY OF ANY KIND, EXPRESS OF IMPLIED. WITHOUT LIMITATION, THERE IS NO WARRANTY OF NON- INFRINGEMENT, NO WARRANTY OF MERCHANTABILITY, AND NO WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ALL WARRANTIES ARE EXPRESSLY DISCLAIMED. USER ASSUMES THE FULL RISK OF USING SUCH PRODUCTS AND DOCUMENTS. IN NO EVENT SHALL USB-IF BE LIABLE FOR ANY ACTUAL, DIRECT, INDIRECT, PUNITIVE, OR CONSEQUENTIAL DAMAGES ARISING FROM SUCH USE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SALE OF PRODUCTS AND TESTING COMPONENTS THROUGH THIS ORDER FORM DOES NOT IMPLY SUCH PRODUCTS AND TESTING COMPONENTS ARE CERTIFIED AND/OR ENDORSED BY USB-IF. THESE PRODUCTS ARE FOR TESTING PURPOSES ONLY AND NOT FOR RESALE. Page 2 of 6
The following table is for use by Non-Members of the USB Implementers Forum: Please email the completed order form including payment information to admin@usb.org. You may also fax or mail your completed order form. USB Implementers Forum 3855 SW 153rd Drive Beaverton, OR 97003 USA Tel: 503-619-0426 Fax: 503-644-6708 Product Code: Description: Quantity: Non- Members USB31CET USB 3.1 USB (10 GT/s) Type-C Electrical Test Fixture Kit $2900.00 USD Extended Price: USB31AET USB 3.1 USB (10 GT/s) Type-A and Micro-B Electrical $2200.00 USD Test Fixture Kit USBLSTD Low Speed Functional Compliance Test Device $110.00 USD USBFSTD Full Speed Functional Compliance Test Device $300.00 USD USB3ET USB 3.0 Electrical Test Fixture Kit OUT OF STOCK $950.00 USD OUT OF STOCK USB2SIGQUAL USB 2.0 Hi-Speed Signal Quality Test Fixture Set $900.00 USD Total Payment Due: Shipping and Handling Fees are included in the prices above. Duties, customs and other taxes are not included within the above prices. You should receive an invoice from the carrier and/or customs for any additional expense incurred. It is your responsibility, and not that of USB-IF, to pay these taxes. ALL PRODUCTS AND DOCUMENTS OFFERED FOR SALE BY USB-IF ARE PROVIDED "AS IS" AND WITHOUT ANY WARRANTY OF ANY KIND, EXPRESS OF IMPLIED. WITHOUT LIMITATION, THERE IS NO WARRANTY OF NON- INFRINGEMENT, NO WARRANTY OF MERCHANTABILITY, AND NO WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. ALL WARRANTIES ARE EXPRESSLY DISCLAIMED. USER ASSUMES THE FULL RISK OF USING SUCH PRODUCTS AND DOCUMENTS. IN NO EVENT SHALL USB-IF BE LIABLE FOR ANY ACTUAL, DIRECT, INDIRECT, PUNITIVE, OR CONSEQUENTIAL DAMAGES ARISING FROM SUCH USE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SALE OF PRODUCTS AND TESTING COMPONENTS THROUGH THIS ORDER FORM DOES NOT IMPLY SUCH PRODUCTS AND TESTING COMPONENTS ARE CERTIFIED AND/OR ENDORSED BY USB-IF. THESE PRODUCTS ARE FOR TESTING PURPOSES ONLY AND NOT FOR RESALE. Page 3 of 6
Shipping Information: Orders must contain a complete shipping address and phone numbers for items to be fulfilled. No P.O. Boxes. Ship Attention To: Address 1: Address 2: City: Zip / Postal Code: State/Province: Country: Payment Options and Information: Payment in full is required before items will ship. The USB-IF does NOT consider receipt of a purchase order to be payment in full. The USB-IF accepts credit card, check, ACH transfer, and wire transfer. All funds must be in USD. Remittance Address: USB Implementers Forum 3855 SW 153rd Drive Beaverton, OR 97003 Credit Card: The USB-IF accepts VISA, MasterCard, and American Express. Please find a credit card authorization form on the next page. Check: Please make checks (drawn/payable from a United States Bank only) payable to USB Implementers Forum. Wire/ACH Transfer: If you wish to conduct a wire/ach transfer, please contact us at admin@usb.org. The sender is responsible for wire fees charged by the transferring bank and must include sufficient funds for payment of these fees in the amount transferred. Please ensure that your company name, the contact person s name and invoice number (if applicable) are included on all payments to ensure that your request can be efficiently processed. Payment in full is required before items will ship. The USB-IF does not consider receipt of a purchase order to be payment in full. Page 4 of 6
USB Implementers Forum 3855 SW 153 rd Drive Beaverton, OR 97003 USA Tel: 503-619-0426 Fax: 503-644-6708 Email: admin@usb.org Credit Card Charge Authorization Form Company Information: Address 1: Address 2: City: Zip / Postal Code: State/Province: Country: Card Holder Information: Card Holder Name: Telephone: Email: Fax: Billing Address 1: Billing Address 2: City: Zip / Postal Code: State/Province: Country: Credit Card Information: Card Type: (Please select one) VISA MASTERCARD AMERICAN EXPRESS Card Number: Expiration: / CVV code: (for Visa & MasterCard: 3-digit code on back of card; for American Express: 4-digit code on front of card) Card Holder Name (as it appears on the card): I authorize USB Implementers Forum to charge US$ Card Holder Signature: Date: ALL of the above information must be completed. Incomplete forms WILL NOT be accepted. Page 5 of 6
Purchasing/Return Policy If you wish to purchase products described on the usb.org web site, you will be asked to supply certain information, including but not limited to credit card or other payment information. You agree all information you provide to the USB-IF will be accurate, complete and current. You agree to pay all charges incurred by authorized users of your account and credit card or other payment mechanism at the prices in effect when such charges are incurred. You will also be responsible for paying any applicable taxes, and shipping and handling charges relating to your purchases. Non-Defective Products We will not accept returns on non-defective products. Defective Products Defective products may be returned for either exchange or repair (at the discretion of the USB-IF) within 30 days from the shipment date. No defective product will be accepted without a return authorization (RA) number. To request a RA number, please contact a USB-IF Customer Service Specialist; please see the contact information below. RA numbers are valid for ten business days after issue. Your RA number(s) must appear clearly on the shipping label of the return shipment. Affix a label to the box: PLEASE DO NOT MARK THE BOX ITSELF IN ANY WAY. If you have questions, please contact us at: USB Implementers Forum 3855 SW 153 rd Dr. Beaverton, OR 97003 Phone: 1-503-619-0426 Fax: 1-503-644-6708 Email: admin@usb.org Page 6 of 6