Parts list "RS 7"-Look Edition for Audi A8 + S8 Typ D4 4H Facelift - Model (A8 from 09.2013 - / S8 from 2014 - ) A8 D4 4H Facelift-model, from 09.2013 onwards - / S8 from 2014 onwards Product Parts-No. Mat. Exterior Parts Front bumper "RS 7"-Look Facelift for cars with or without headlight washer system and with Parking sensors (PDC / Parktronic), with or without ACC Distance Radar. Into this front bumper the serial front grill of the Audi A8 D4 4H Facelift-front grill and the S8 Facelift-front grille can be inserted (they are not part of delivery). This new front bumper is suitable for the S8 D4 4H Facelift. But only, if you use and order the headlamp washer caps 8775. Additionally needed are the lamella mesh inserts 8752, or 8772 or 8772-CB and - only for the S8 model- the article 8775. 8771 HPC Top Material: HPC - High-Performance-Composite - Material, from BASF- Chemical.
Rear skirt "Diffusor RS 7-Look" Facelift with openings for double tail pipes (not for the serial square tail pipes from original bumper). Replaces the lower part of the serial rear bumper, with one big opening on the left & right side for the oval double tailpipes 8782 or the 4-tube sports muffler 8740. The kit consists of two pieces, the lower diffuser can be removed. This diffuser is also available as Carbon version (Option), see the listing "Carbon parts" below. Top Material: HPC - High-Performance-Composite - Material, from BASF- Chemical. 8773 HPC 1 set Side Skirts "RS 7"-Look. Set for A8 normale (shorter) wheel base (not 'A8 L') For the left & right side. The sills are glued onto the car underneath the doors. Sportive "RS7-Look" and less dirt on the doors. Not for Audi S8 and not for Audi A8 L! Or you use for your S8 the original Audi-base side skirt of the normale A8 as your base, with this base you can fit the new Side Skirt 8774 at a S8. Top Material: HPC - High-Performance-Composite - Material, from BASF- Chemical. 8774 HPC 1 set Rear Spoiler Facelift for the trunk / boot. The spoiler is optional available as Carbon version, see the listing "Carbon parts" below. 8777 HPC This Rear Spoiler is suitable for S8, too. Top Material: HPC - High-Performance-Composite - Material, from BASF-Chemical. Alternative zu Seitenscheller-Satz 8774: Side Sills set for A8 normale (shorter) wheel base (not 'A8 L'). For the left & right side. The sills are glued onto the car underneath the doors. The car looks "longer" and "flat" and less dirt on the doors. Not suitable for the S8 model and not for Audi A8 L! 8754 PKG 1 set Accessories for Front bumper 8771
Version Basic: "RS" Lamella mesh inserts "RS 5"-Look - needed for Hofele-Design Front bumper 8771. 8752 OEM 1 set Set for left & right side. Only for cars without ACC. Version 1: "RS" Lamella mesh inserts with "Air-Vent"- side air intakes. "RS 7"-Look For cars with or without ACC Distance Radar. 8772-CB1 OEM + CB 1 set Carbon Air-Vents, raw, unpainted - needed for Hofele-Design Front bumper 8771. Set for left and right side. Version 2: "RS" Lamell a mesh inserts with "Air-Vent"-air intakes. For cars with or without ACC distance radar control. "RS 7"-Look. Carbon Air-Vents, 8772-CB2 OEM + HPC 1 set -Painted in several layers of Clear Coat - Suitable for Hofele-Design Front bumper 8771. Set for left and & right side. Version 1: Carbon- Centre Front Lip / Flipper - Carbon unpainted - no clear coat painted. In RS7-Look 8779-CB1 Could be installed on the HOFELEfront bumper 8751 (all versions) Version 2: Carbon- Centre Front Li / Flipper - Carbon painted with several layers of clear coat. In RS7-Look 8779-CB2 Could be installed on the HOFELEfront bumper 8751 (all versions) Front grille For your information: The original Front grills of your Audi A8 V6, V8, W12, S8 could be still used in the Hofele bumper 8771. The below offered Front grills are alternatives to up-grade A8 V6 / V8 models.
Front grill "W12" model 2014 Facelift Optionally for the Hofele-Design front bumpers 8771. 8776-W12 OEM Front grill "S8" model 2014 Facelift 8776-S8 OEM Optionally for the Hofele-Design front bumpers 8771. Front grill "RS8"-Look model 2014 Facelift 8776-RS8 ABS 1 Stück Optionally for the Hofele-Design front bumpers 8771. Extras and TUEV-Certificate / homologation TUEV approval papers for the front bumpers needed to get the car through the TUEV inspection and to get the kit approved for your car, not needed for export. Because of the new pedestrian safety requirements a lot of tests incl. a crash-test have been made to get the TUEV papers for this body kit. These additional costs are charged with this fee. 8770-TÜV Headlight washer caps and towing hook cover needed only for the S8 model for the use of the front bumpers H 8771. 8775 OEM 1 set CARBON Parts Rear Skirt with Carbon-Diffusor "RS 7-Look" Facelift with openings for the double tailpipes. Replaces the lower part of the serial rear bumper, with one big opening on the left & right side for the oval double tailpipes 8782 or the 4-tube Sport muffler system 8780. The kit consists of two pieces, the lower diffuser can be removed. This diffuser is made of a cover of real Carbon and multiple layers of clear coat. 8773-CB HPC + CB 1 set Carbon Rear Spoiler Facelift for the trunk / boot. The spoiler is made of a cover of real Carbon and multiple layers of clear coat. This Rear Spoiler is suitable for S8, too. 8777-CB HPC + CB
Carbon Mirror housing the serial mirror glas and electrics has to be inserted. Two pieces, one for the left & one for the right side. Made with a cover of real Carbon and multiple layers of clear coat. 8778-CB CB 1 set Sport Tail Pipes SportTail pipes Set "Double Oval interlaced" Made of polished stainless steel. Set of double tubes for the left & right side, the tailpipes have to be welded onto the serial A8 mufflers. Tailpipe diameter 250 x 95 mm. 8782 E 1 set Especially made for the combination with the Hofele-Design rear aprons 8773 & 8773-CB. Suitable for Petrol / Gasoline & Diesel engines. Suitable for A8 (short wheel base) and A8 L (Long wheel base)! Interior Luxury HOFELE leather interior "StarLight Seats" Bi-colour in combination with different colours. High-quality Nappa-Leather, for example the Bentley leather colour "Fawn". Set for the front & rear seats. Also includes the covering of - door panels and door arm rests - arm rest between the front seats - arm rest between the rear seats - leather parts of the steering wheel in the same colour as the seats 1 set These high-qulity seat covers can be installed onto the original Audi seat frames by a professional upholsterer instead of the original Audi seat covers. Another option is to send the original seats for the conversion to Hofele-Design in Germany. Installation costs for the "StarLight Seats" leather interior - removal of the sets, door panels and arm rests - removal of the original seat covers from the frames - installation of the new "Bi-Colour" leather seat covers - installation of the seats, door panels and arm rests Sport Wheel Program
HOFELE "Rotiss-18" Designer wheel with five double spokes size: 8,0 x 18" offset 35, PCD/H: 5x112, CH 66,6 Colour silver polished. TÜV-approved for the following tire sizes: 235/55, 245/50 & 255/50 RO80185 SP HOFELE "Rotiss-19" Designer wheel with five double spokes size: 8,0 x 19" offset 35, PCD/H: 5x112, CH 66,6 Colour silver polished. TÜV-approved for the following tire sizes: 235/50, 245/45 & 255/45 RO80195 SP HOFELE "Reverso-II-20" Designer wheel in 5-star-design size: 9,0 x 20" PCD/H: 5x112 offset 35 CH 66,6 Colour Sterlingsilver-met. TUEV approved for the following tire sizes: 235/45, 245/40, 255/40, 265/40 & 275/35 RVII90205 SP HOFELE "Reverso-II-20" BLACK or TITAN-GREY RS Designer wheel in 5-star-design size: 9,0 x 20" PCD/H: 5x112 offset 35 CH 66,6 Colour black or Titan-Grey RS TUEV approved for the following tire sizes: 235/45, 245/40, 255/40, 265/40 & 275/35 RVII90205 BP HOFELE "Reverso-I-21" size: 9,5 x 21" PCD/H: 5x112 offset 35 CH 66,6 Colour Sterlingsilver-met. TUEV approved for the following tire sizes: 245/35, 255/35, 265/35, 275/30 & 275/35 RVI95215 SP HOFELE "Reverso-I-21" size: 9,5 x 21" PCD/H: 5x112 offset 35 CH 66,6 Colour Black or free colour choice. TUEV approved for the following tire sizes: 245/35, 255/35, 265/35, 275/30 & 275/35 RVI95215 BP
HOFELE "Reverso-II-22" size: 10J x 22" PCD/H: 5x112 offset 50 CH 66,6 Colour Sterlingsilver-met. The wheel can only be used on the A8 D4 4H in combination with wheel spacers, minimum Spacers with 15 mm thickness each side (Spacer Package 1). See the "Chassis" listing below. Single-TUEV for the tire size 265/30x22" RVII100225 11266650 SP Designerfelge im 5-Stern-Design HOFELE "Reverso-II-22" BLACK or TITAN-GREY RS size: 10J x 22" PCD/H: 5x112 offset 50 CH 66,6 Colour black or Titan-Grey RS The wheel can only be used on the A8 D4 4H in combination with wheel spacers, minimum Spacers with 15 mm thickness each side (Spacer Package 1). See the "Chassis" listing below. Single-TUEV for the tire size 265/30 x 22" RVII100225 11266650 BP HOFELE Typ R-600 Alloy-wheel in " 5 -Y-Spokes" design, 1-part wheel. size: 9,5J x 22", PDC/H: 5x112, CH: 66,6, offset 50 Colour: Sterling Silver-met. For following tyre size for A8: 265/30 R 22 97Y axle load maximum 1400 kg. The wheel can only be used on the A8 D4 4H in combination with wheel spacers, minimum Spacers with 15 mm thickness each side (Spacer Package 1). See the "Chassis" listing below Single registration with TUEV Wheel Strength Test Certificate. R-600-9,5x22-5x112 Wheels complete with fitted Tire - price per piece - Wheel + Tire "Rotiss-18" Designer wheel with five double spokes size: 8,0 x 18" offset 35, PCD/H: 5x112, CH 66,6 Colour silver polished. Incl. quality tire in the size 245/50 Wheel +Tire "Rotiss-19" Designer wheel with five double spokes size: 8,0 x 19" offset 35, PCD/H: 5x112, CH 66,6 Colour silver polished. Incl. quality tire in the size 245/45
Wheel + Tire "Reverso-II- 20" Designer wheel in 5-star-design size: 9,0 x 20" PCD/H: 5x112 offset 35 CH 66,6 Colour Sterlingsilver-met. Incl. quality tire in the size 265/40 Wheel + tire "Reverso-II- 20" BLACK or TITAN-GREY RS Designer wheel in 5-star-design size: 9,0 x 20" PCD/H: 5x112 offset 35 CH 66,6 Colour Black or Titan-Grey RS Incl. quality tire in the size 265/40 Wheel + Tire "Reverso-II- 22" size: 10J x 22" PCD/H: 5x112 offset 50 CH 66,6 Colour Sterlingsilver-met. The wheel can only be used on the A8 D4 4H in combination with wheel spacers, minimum Spacers with 15 mm thickness each side (Spacer Package 1), see the "Chassis" listing below. Incl. quality tire in the size 265/30 Wheel + tire "Reverso-II- 22" BLACK or TITAN-GREY RS size: 10J x 22" PCD/H: 5x112 offset 50 CH 66,6 Colour Black or Titan-Grey RS The wheel can only be used on the A8 D4 4H in combination with wheel spacers, minimum Spacers with 15 mm thickness each side (Spacer Package 1), see the "Chassis" listing below. Incl. quality tire in the size 265/30 Chassis Package 1: Wheel spacers for Reverso II 22" wheels Set with four pieces, incl. 20 longer wheel bolts M14x1,5x?? In combination with the Reverso II-wheels in the size 10 x 22" you need the following spacers: front 15 mm / each side rear 15 mm / each side 8762 St 1 set Package 2: Wheel spacers Attetion to the space and offset in combination with your wheel size. Set with four pieces, incl. 20 longer wheel bolts M14x1,5x47 In combination with the Reverso II-wheels in the size 10 x 22" you need the following spacers: front 20 mm / each side rear 22,5 mm / each side 8763 St 1 set
ETS-System "A8 Facelift" Electronic Lowering module for the front & rear axle of the Audi A8. Speed-related electronic chassis optimization. Only for cars with air suspension! Only for cars with Parking Assistent or Parktronic Plus (works order code 7X2, 7X5), both items are standard in S8 and in W12. Lowering of approx. 30mm at the front & 20mm at the rear axle, additionally each axle can be independently fine-adjusted another +/- 20mm so the maximum lowering is 50mm at the front & 40mm at the rear axle. - speed-related lowering (when driving more than 70 km/h the lowering is deactivated to get the full comfort & safety) - the serial settings in the menue can still be chosen but each setting is lowered - the module has a switch with which the module can be deactived in case you need the serial height. - the module has a long wire with which the switch can be guided and installed directly in the drivers compartment for easy control access - easy "Plug&Play" installation, takes approx. 30 minutes. The installation of the switch in the drivers compartment takes approx. 1,5 to 2 hours. - TUEV approved 8791 1 set Motortuning "Hofele Dynamic Pro" More Power - More HP / kw - More Torque / Nm - Faster Acceleration - Higher end speed (if not regulated or at limits) Electronical increase of power by installation of an additional engine power control unit, to activate the engine reserves and for the optimization of the fuel consumption. With controlled driving a reduction of the gasoline / diesel consumption of up to 1 liter is possible. Plug-In-system, easy installation, the tuning kit can be shipped. If needed the tuning kit can be easily removed by driver - only plug-off. No TUEV approval. 2 years warranty on the "Dynamic Pro"- power control unit. An additional engine and gear box warranty / guarantee is available with extra charge. car type and engine version für A8 D4 (4H) Facelift 3,0 TDI 'Clean Diesel' V6 3,0l Diesel, 2967 ccm³, für A8 D4 (4H) Facelift 4,2 TDI Clean Diesel, V8 Diesel 4,2l Diesel, 4134 ccm³, für A8 D4 (4H) 3,0 TFSI, V6 Benziner 3,0l Benziner, 2995 ccm³, für A8 D4 (4H) 4,0 TFSI, V8 Benziner Singel-Turbo 4,0l Benziner, 3993 ccm³, für S8 D4 (4H) 4,0 TFSI, V8 Benziner Bi-Turbo 4,0l Benziner, 3993 ccm³, serial output 190 kw 258 PS 580 Nm 283 kw 385 PS 850 Nm 213 kw 290 PS 420 Nm 320 kw 435 PS 600 Nm 382 kw 520 PS 650 Nm 221 KW 300 HP 660 Nm 340 KW 460 HP 998 Nm 256 KW 348 HP 504 Nm 385 KW 520 HP 680 Nm 415 KW 565 HP 740 Nm increase of power output about: HP / KW torque about: NM
For "Dynamic Pro" and "Performance Package": Attention: The here above declared increased motor power is "approx.-data". The real increase depends on the serial basic motor and its scattering of the final individual basic power of each motor. This scattering could be significant and as result of this, the power increase could be more or less than the above offered power data. stainless steel alloy wheels steel verzinkt und pulverbeschichtet original parts from car manufacturer ABS plastic polyurethane foam flexible RIM plastic combination of plastic and fibreglas Material: HPC High Performance Composite, Special HOFELE-Material from German Chemical-Group BASF Compount Polyester material. Higher Cold and Heat resistant CompositeCompound-Material on Polyester-Base (BASF) with smooth internal layers of fibre mats liners. Highest Quality. Often used for Racecars and production of Air Plane gliders. Carbon Covered Parts With real Carbon covered basic HPC plastic parts. Painted additionally with several layers of Clear Coat. Highest Quality. abbreviation E ST MVP OEM ABS PU RIM PKG HPC CB "Audi" + "A8" +"S8" + "RS5" + "RS7" are registered trademarks of the Audi AG Ingolstadt errors excepted Hofele-Design GmbH Hermann-Schwarz-Str. 11 73072 Donzdorf / Germany Tel. 07162-912390 Fax 07162-91239-25 Email: info@hofele.com Homepage: www.hofele.com "Copyright -C- 2014 for all products, by HOFELE-DESIGN GmbH, Address: Hermann-Schwarz-Str. 11, D-73072 Donzdorf, GERMANY www.hofele.com, E-mail: info@hofele.com International Registered -R- Parts, Design and Trademark!" All Copies of Hofele-products or unallowed using of Hofele-Trademarks, will be punished by intensive costs worldwide by lawyers. Stand 11. November 2014