Vickers PVM Piston Pumps

Vickers PVM Piston Pumps 18-141cc 3 (1.1-8.6in 3 ) M-Series Industrial Variable Displacement M-Series Mobile Variable Displacement

Table of Contents M Series Variable Displacement Piston Pumps Principles of Operation... 3 Hydraulic System Design Calculations... 4 Introduction... 5 Model Code Selection.... 6 Model Code Options... 7 Specifications and Performance............................................................................... 9 Control Options... 12 Performance Industrial & Mobile PVM18... 16 PVM2... 21 PVM45... 26 PVM5... 31 PVM57... 36 PVM63... 41 PVM74... 46 PVM81... 51 PVM98... 56 PVM16... 61 PVM131... 66 PVM141... 71 Dimensions PVM18/2........................................................................................ 76 PVM45/5........................................................................................ 83 PVM57/63........................................................................................ 9 PVM74/81........................................................................................ 95 PVM98/16........................................................................................ 99 PVM131/141....................................................................................... 13 Mounting Flange Options.... 18 Shaft Options.... 19 Shaft Selection Data... 112 Port Options.... 113 Operating Requirements and Recommendations... 115 Installation and Start-up.... 116 2 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Principles of Operation In axial piston pumps, the pistons reciprocate parallel to the axis of rotation of the cylinder block. The simplest type of axial piston pump is the swash plate in-line design. The cylinder block in this pump is turned by the drive shaft. Pistons fitted to bores in the cylinder block are connected through piston shoes and a shoe plate, so that the shoes bear against an angled swash plate. As the block turns, the piston shoes follow the swash plate, causing the pistons to reciprocate. The ports are arranged in the valve plate so that the pistons pass the inlet as they are pulled out and pass the outlet as they are forced back in. The displacement of axial piston pumps is determined by the size and number of pistons, as well as the stroke length which is determined by the angle of the swash plate. In variable displacement models of the in-line pump, the swash plate is installed in a movable yoke. Pivoting the yoke on pintles changes the swash plate angle to increase or decrease the piston stroke. Piston Pump Operation EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 3

Hydraulic System Design Calculations Basic Formulas Output Flow (Q) cm 3 /r x rpm in 3 /r x rpm lpm = gpm = 1 231 Power (P) l/min x gpm x psi kw = hp = 6 1714 Shaft Torque (M) x cm N-m = 3 /r psi x in lb-in = 3 /r 62.8 6.28 Shaft Speed (n) Efficiencies gpm actual Volumetric Nv = gpm theorectical lb-in actual Mechanical Nm = lb-in theorectical Total Nt = Nv x Nm Q n P M p 1 x 1/min 231 x gpm rpm = RPM = cm 3 /r in 3 /r Output Power (P) N-m x RPM lb-in x rpm kw = hp = 9549 63,25 Volumetric Displacement lpm x 1 gpm x 231 cm 3 /r = in 3 /r = rpm rpm Basic Formulas = 1 Newtons/cm 2 gpm = gallons per minute hp = horsepower lb-in = pound inch lb-ft = pound feet kw = kilowatt kgf = kilograms force l/min = liters per minute N-m = Newton meters psi = pounds per square inch rpm = revolutions per minute Commonly Used Conversions To Convert Into Multiply by psi 14.5 cm 3 in 3.612 C F ( C x 1.8) +32 gallons (US) liters 3.785 kg lbs 2.25 kgf/cm 2 psi 14.2 kw hp 1.341 liters US Gallons.2642 mm inches.3937 N-m lb-in 8.85 N-m lb-ft.7375 F C ( F-32)/1.8 hp kw.7457 inch mm 2.54 in 3 cm 3 16.39 lb-in N-m.113 lb-ft N-m 1.356 lbs kg.4535 psi.6896 psi kgf/cm 2.737 Note: Performance charts can be found on subsequent pages. 4 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Introduction Eaton Vickers M Series mobile pumps are open circuit, axial piston designs. A variety of controls provides the ability to match the pumps to each application. Efficiency of the pump controls allows downsizing of system cooling needs, allowing a smaller and less expensive design to be used. Alternatively, cooling capacity could be kept the same and the flow capability of the system increased, thus improving performance and customer satisfaction. A strong proven rotating group allows the pumps to handle pressures to 28 (4 continuous and 32 (46 intermittent with less maintenance cost. High-load bearings and a stiff drive shaft help provide a pump life of 5 hours at rated mobile conditions, reducing operating costs and extending operating life. M Series pumps feature a saddle-type yoke with steel-backed polymer bearings. The stiff yoke reduces deflection and allows even loading of bearings, improving life. A single control piston reduces loading on the yoke, resulting in reduced pump size which allows installation in tighter locations. M Series pumps operate at a level of quietness that exceeds the requirements of today s demanding work conditions. The pumps feature a unique three-piece envelope (flange, housing and valve block) specifically created for low fluid-borne and structure-borne noise levels. Another pump feature a bimetal timing plate improves pump filling characteristics which, in turn, reduce fluid-borne noise and extend pump life. Proximity of the pump to the vehicle operator demands a low noise level in the cab. M Series pumps reduce, or in some cases remove, the need for damping riers between the noise source and the operator. This saves money on the installed cost of the system while improving customer comfort. An adjustable maximum stop provides a means of tuning flow to your system, while gauge ports allow monitoring of inlet and outlet conditions. These standard features reduce system complexity and cost. Mounting flanges are offered in SAE and ISO con figurations, and ports are offered in SAE, ISO, and BSPP in both tube and flange versions. This provides a wide variety of installation opportunities for global machine design. Side- or end-ported models are available to facilitate plumbing and help fit the pump to your machine space needs. Multiple drain ports allow many mounting orientations, reducing installed costs. M Series pumps are capable of operating with many types of hydraulic fluids used in industrial and mobile systems. High-water-content and phosphate ester fluids can be accommodated, in addition to the typical petroleum based and synthetic fluids. Typical Applications Loader backhoes Vibratory cable plows Mining machinery Dump truck lifts Agriculture tractors Chemical applicator trucks Railroad equipment Container handling, all-terrain, and truck cranes Vibratory cable plows Mining machinery and tunnel boring equipment Utility boom, off-road dump, and refuse trucks Material handling trucks and rough terrain fork lifts Concrete and asphalt pavers Feller/bunchers, forwarders, and log loaders Crawler dozers Articulate haulers Mini-excavators Features and Benefits Long pump life Quiet pump operation Inlet and outlet gauge ports and adjustable maximum displacement stops standards Astonishingly low 4% pressure ripple Low installed and operating costs Reduced maintenance Flexibility in machine design Compact size saves space Design promotes leak-free system EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 5

Model Code Selection PVM 18 M R 1 A E 1 AA A 28 A A 1, 2, 3 4, 5, 6 7 8 9, 1 11 12 13, 14 15, 16 17 18, 19 2, 21 22, 23 24 25 26 27 28 1, 2, 3 Product Series PVM M Series Variable Piston Pump 4, 5, 6 Displacement Fourteen displacements available 23 and 28 continuous ratings 7 Valve Plate M Mobile Equipment Speeds (Higher Speed) 8 Rotation R Clockwise (Righthand) L* Counter-clockwise (Lefthand) 9, 1 Shaft Standard SAE and ISO splined versions (Other configurations optional) 11 Mounting Flange Thirteen options in SAE and ISO mounts 12 Main Port Location E** End Ported S Side Ported 13, 14 Main Port Type SAE & ISO tube ports and 4-bolt flange (Other configurations optional) 15, 16 Pump Special Features None AA Adjustable Maximum Displacement Stop and single shaft (standard) AB Double Shaft Seal, Two Way 17 Control None A Pressure Compensator B Pressure and Flow Compensator with Bleed Orifice C Pressure and Flow Compensator with Plugged Orifice E Industrial Control (57cc through 141 cc only) 18, 19 Pressure Compensator Setting None 7 7 (Adjustable between 4 and 13 ) 23 23 (Adjustable between 13 and 32 ) 28 28 (Adjustable between 13 and 32 ) 2, 21 Flow Compensator Setting None 11 11 setting 2 2-2 setting 24 24-24 setting 22, 23 Torque Limiter Setting None (Not available on M Series) 24 Compensator Special Features None 25 Auxiliary Mounting Pad *** None (Auxiliary mounting available on all frame sizes) 26 Paint No Paint A Standard Blue Paint 27 Customer Identification None (Contact Eaton for Options) 28 Design Code A A (Initial Release) * Not available on 74, 81, 98 and 16 End Port ** Not available on 74, 81, 98 and 16 LH *** Through drive not available on the LH 6 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Model Code Options 4,5,6 Maximum geometric displacement Displacement Code 18 2 45 5 57 63 74 81 98 16 131 141 cm 3 /r 18, 21,1 45,1 5, 57,4 63,1 73,7 81, 98,3 16,5 131,1 141, in 3 /r 1.1 1.29 2.75 3.5 3.5 3.85 4.5 4.94 6. 6.5 8. 8.6 9,1 Shaft-end type at electric motor end Shaft Code Description PVM18/2 PVM45/5 PVM57/63 PVM74/81 PVM98/16 PVM131/141 SAE, SAE A, Straight Keyed 1 SAE, SAE 19-1, Straight Keyed 2 SAE, SAE A, 9T Spline 3 SAE, SAE A, 11T Spline 4 SAE, SAE B, Straight Keyed 5 5 SAE, SAE B-B, Straight Keyed 6 6 6 SAE, SAE B, 13T Spline 7 7 7 SAE, SAE B-B, 15T Spline 8 8 8 SAE, SAE C, Straight Keyed 9 9 9 9 SAE, SAE C-C, Straight Keyed 1 1 1 SAE, SAE C, 14T Spline 11 11 11 11 SAE, SAE C-C, 17T Spline 12 12 12 SAE, SAE D, Straight Keyed 13 SAE, SAE D, 13T Spline 14 ISO E2N, Straight Keyed 15 ISO E25N, Straight Keyed, Short Spigot 16 ISO E25N, Straight Keyed 17 17 17 ISO E32N, Straight Keyed, Short Spigot 18 18 18 18 ISO E4N, Straight Keyed, Short Spigot 19 19 19 11 Mounting flange specifications Code Description PVM18/2 PVM45/5 PVM57/63 PVM74/81 PVM98/16 PVM131/141 A SAE A, 2-bolt l B ISO 8A2HW l C SAE B, 2-bolt l l l D ISO 1A2HW l l l E SAE C, 2-bolt l l l l F ISO 125-A2HW l l l l G SAE C, 4-bolt l l l l H ISO 125B4HW l l l l J SAE D, 4-bolt l K ISO 16B4HW l l = Available = Not Available EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 7

Model Code Options 13,14 Main Port Options Inlet Code Description Outlet PVM18/2 PVM45/5 PVM57/63 PVM74/81 PVM98/16 PVM131/141 Inlet 2 24 24 1 SAE J1926 (End ports only) Tube Ports Outlet 12 16 16 (End ports only) 2 SAE J518 Inlet 1.25 inch 2. inch 2. inch 2. inch 2.5 inch 2.5 inch Flange Ports Outlet.75 inch 1. inch 1. inch 1. inch 1. inch 1.25 inch* Inlet M42 M48 M48 3 ISO 6149-1 (End ports only) Tube Ports Outlet M27 M33 M33 (End ports only) 4 ISO 6162 Inlet 32mm 51mm 51mm 51mm 64mm 64mm Flange Ports Outlet 19mm 25mm 25mm 25mm 25mm 32mm* British Standard 5 Parallel Pipe Inlet G 1-1/4 G 1-1/2 Tube Ports Outlet G 3/4 G 1 *SAE Code 62, high pressure series, or ISO 4. Other flange ports are SAE Code 61, standard pressure series, or ISO 25-35. 25 Thru-Drive Options Code Description PVM18/2 PVM45/5 PVM57/63 PVM74/81* PVM98/16 PVM131/141 O Single pump, non-thru-drive l l l l l l A SAE A, 2-bolt, 9T spline l l l l l l B SAE A, 2-bolt, 11T spline l l l l l C SAE B, 2-/4-bolt, 13T spline l l l l l D SAE B-B, 2-/4-bolt, 15T spline l l l l l E SAE C, 2-/4-bolt, 14T spline l l l l F SAE C-C, 2-/4-bolt, 17T spline l l l G ISO 8-A2HW, 9T SAE spline l l l l l l H ISO 8-A2HW, 11T SAE spline l l l l l J ISO 1-A2/B4HW, 13T SAE spline l l l l l K ISO 1-A2/B4HW, 15T SAE spline l l l l L ISO 125-A2/B4HW, 14T SAE spline l l l l M ISO 125-A2/B4HW, 17T SAE spline l l l l = Available = Not Available * Not available on the 74/81 LH 8 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Specifications and Performance Industrial Displacement, Pressure and Flow Ratings At 5 C (12 F), SAE 1W oil, 1 absolute ( psig) inlet Maximum Maximum Flow at 21 (3 Geometric Maximum Pressure ( l/min (USgpm) Displacement @18 @15 @12 @1 Model Series cm /r (in /r) 3 3 Continuous Intermittent* Peak** r/min r/min r/min r/min PVM18 18 (1.1) 28 (4) 32 (46) 35 (5) 31 (8.2) 26 (7) 21 (5.5) 17 (4.5) PVM2 21,1 (1.29) 23 (33) 25 (36) 28 (4) 35 (9) 29 (8) 23 (6) 19 (5) PVM45 45,1 (2.75) 28 (4) 32 (46) 35 (5) 76 (2) 65 (17) 49 (13) 42 (11) PVM5 5, (3.5) 23 (33) 25 (36) 28 (4) 87 (23) 75 (2) 62 (16) 49 (13) PVM57 57,4 (3.5) 28 (4) 32 (46) 35 (5) 12 (27) 85 (22.4) 66 (17.4) 54 (14.3) PVM63 63,1 (3.85) 23 (33) 25 (36) 28 (4) 111 (29) 93 (24) 74 (19) 6 (16) PVM74 73,7 (4.5) 28 (4) 32 (46) 35 (5) 127 (33.5) 16 (28) 86 (22.7) 7 (18.5) PVM81 81, (4.94) 23 (33) 25 (36) 28 (4) 139 (37) 116 (31) 93 (25) 76 (2) PVM98 98,3 (6.) 28 (4) 32 (46) 35 (5) 17 (45) 141 (37) 112 (29.6) 92 (24.3) PVM16 16,5 (6.5) 23 (33) 25 (36) 28 (4) 187 (49) 155 (41) 123 (32) 12 (27) PVM131 131,1 (8.) 28 (4) 32 (46) 35 (5) 215 (57) 178 (47) 141 (37) 118 (31) PVM141 141, (8.6) 23 (33) 25 (36) 28 (4) 238 (63) 199 (53) 158 (42) 131 (35) **Less than 1% of duty cycle. **Momentary system pressure spikes only. Speed, Power and Torque Ratings At 5 C (12 F), SAE 1W oil, 1 absolute ( psig) inlet Maximum Maximum Torque at Operating 21 Approximate Model Speed Maximum Power at 21 (3 kw (hp) (3 Weight Series r/min @18 r/min @15 r/min @12 r/min @ 1 r/min Nm (lb-ft) kg (lb) PVM18 18 16 (22) 13 (18) 11 (15) 9 (12) 84 (62) 15 (33) PVM2 18 14 (18) 11 (15) 9 (12) 8 (1) 73 (54) 15 (33) PVM45 18 41 (55) 34 (46) 27 (37) 23 (31) 221 (163) 24 (52) PVM5 18 35 (47) 3 (4) 28 (38) 23 (31) 19 (14) 24 (52) PVM57 18 52 (7) 44 (59) 36 (49) 29 (39) 272 (21) 36 (79) PVM63 18 42 (57) 36 (48) 29 (39) 24 (32) 228 (168) 36 (79) PVM74 18 63 (84) 52 (7) 42 (56) 35 (47) 334 (246) 45 (99) PVM81 18 56 (75) 46 (62) 35 (47) 28 (37) 286 (211) 45 (99) PVM98 18 88 (118) 72 (97) 58 (78) 48 (64) 464 (342) 55 (121) PVM16 18 72 (97) 6 (8) 48 (64) 4 (54) 383 (282) 55 (121) PVM131 18 113 (152) 94 (126) 75 (11) 63 (85) 596 (44) 66 (145) PVM141 18 94 (126) 79 (16) 63 (85) 53 (71) 497 (367) 66 (145) Standard Response Times* Model Series On Stroke (msec) Off Stroke (msec) PVM18 3 25 PVM2 39 26 PVM45 14 4 PVM5 14 4 PVM57 65 2 PVM63 85 2 Standard Response Times* Model Series On Stroke (msec) Off Stroke (msec) PVM74 85 3 PVM81 85 3 PVM98 65 25 PVM16 72 29 PVM131 135 3 PVM141 1 3 *Values with pressure compensator control. EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 9

Specifications and Performance Mobile Displacement, Pressure and Flow Ratings At 93 C (2 F), SAE 1W oil, 1 absolute ( psig) inlet Geometric Maximum Pressure ( Maximum Flow at 28 (4 Displacement Flange Ports Tube Ports Model Series cm 3 /r (in 3 /r) Continuous Intermittent* Peak** l/min (USgpm) @ 1 inlet l/min (USgpm) @ 1 inlet PVM18 18, (1.1) 28 (4) 32 (46) 35 (5) 46 (12) @ 28 r/min 46 (12) @ 28 r/min PVM2 2,1 (1.22) 23 (33) 25 (36) 28 (4) 53 (14) @ 28 r/min 53 (14) @ 28 r/min PVM45 45,1 (2.75) 28 (4) 32 (46) 35 (5) 115 (3) @ 26 r/min 16 (28) @ 24 r/min PVM5 5, (3.5) 23 (33) 25 (36) 28 (4) 125 (33) @ 26 r/min 116 (31) @ 24 r/min PVM57 57,4 (3.5) 28 (4) 32 (46) 35 (5) 14 (37) @ 25 r/min 128 (34) @ 23 r/min PVM63 63,1 (3.85) 23 (33) 25 (36) 28 (4) 15 (4) @ 25 r/min 14 (37) @ 24 r/min PVM74 73,7 (4.5) 28 (4) 32 (46) 35 (5) 163 (43) @ 24 r/min PVM81 81, (4.94) 23 (33) 25 (36) 28 (4) 181 (48) @ 24 r/min PVM98 98,3 (6.) 28 (4) 32 (46) 35 (5) 2 (53) @ 22 r/min PVM16 16,5 (6.5) 23 (33) 25 (36) 28 (4) 222 (59) @ 22 r/min PVM131 131,1 (8.) 28 (4) 32 (46) 35 (5) 233 (62) @ 2 r/min PVM141 141, (8.6) 23 (33) 25 (36) 28 (4) 258 (68) @ 2 r/min **Less than 1% of duty cycle. **Less than.5 second. Standard Response Times* Model Series On Stroke (msec) Off Stroke (msec) PVM18 5 2 PVM2 57 22 PVM45 14 4 PVM5 14 23 PVM57 65 2 PVM63 94 2 Standard Response Times* Model Series On Stroke (msec) Off Stroke (msec) PVM74 95 3 PVM81 135 3 PVM98 85 24 PVM16 9 25 PVM131 1 3 PVM141 128 28 *Values with pressure compensator control. 1 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Specifications and Performance Mobile Speed, Power and Torque Ratings At 93 C (2 F), SAE 1W oil, 1 absolute ( psig) inlet Minimum Operating Speed and Pressure r/min Max. Power at Max. Torque at Approximate 1 Inlet,85 Inlet Max. Speed and 28 28 (4 Weight (dry) Model Series Flange Ports Tube Ports Flange Ports (4 kw (hp) Nm (lb-ft) kg (lbs) 28 r/min 24 (32) PVM18 28 r/min 24 (32) 82 (6) 15 (33) 26 r/min 22 (3) 28 r/min 21 (28) PVM2 28 r/min 21 (28) 72 (53) 15 (33) 26 r/min 2 (27) 26 r/min 56 (75) PVM45 24 r/min 53 (71) 198 (46) 24 (52) 22 r/min 48 (64) 26 r/min 51 (68) PVM5 24 r/min 48 (64) 24 (15) 24 (52) 22 r/min 44 (59) 25 r/min 68 (91) PVM57 23 r/min 62 (83) 262 (193) 36 (79) 21 r/min 56 (75) 25 r/min 59 (79) PVM63 24 r/min 57 (76) 225 (166) 36 (79) 22 r/min 52 (69) PVM74 24 r/min 84 (113) 19 r/min 69 (93) 334 (246) 45 (99) PVM81 24 r/min 69 (93) 19 r/min 55 (74) 276 (24) 45 (99) PVM98 22 r/min 15 (141) 18 r/min 86 (115) 457 (337) 55 (121) PVM16 22 r/min 87 (117) 18 r/min 7 (94) 377 (278) 55 (121) PVM131 2 r/min 122 (164) 16 r/min 98 (131) 581 (429) 66 (145) PVM141 2 r/min 12 (137) 16 r/min 81 (19) 483 (356) 66 (145) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 11

Control Options Pressure Compensator Control Code A The pump will provide a continuously modulated flow to meet changing load demands at a preadjusted compensator pressure. At pressures below the compensator setting, the pump will operate at maximum displacement. See model code on page 4 for compensator pressure ranges. Warning: The pressure compensator may be adjusted beyond the rated pressure of the pump. When adjusting the pressure limiter, install a -35 (-5 gage in the outlet gage port and limit the pressure setting to the continuous rated pressure for the pump displacement shown on page 7. Change in Flow B F case drain K inlet gage port K outlet gage port B inlet To load Pressure Cut-off Characteristics of ressure Cut-off Characteristics of Code A Pressure Compensator Control ode A Pressure Compensator Control @ 5 C (12 F), 18 r/min, static conditions 5ϒC (12ϒF), 18 r/min, static conditions Industrial Pressure Cut-off Change in Characteristics Change of Code in A Pressure A Pressure Compensator Pressure A Q Control at 5 C (12 F), static Q conditions. Outlet Flow Outlet Flow Change in Flow B See model code on page spring (pressure) adjustm See model code on page xx for spring (pressure) adjustment ranges. B inlet F case drain C outlet K inlet gage port K outlet gage port To load C outlet Outlet Pressure P Outlet Pressure P Pressure Cut-off Characteristics of Pressure Compensator Control @ 5 C (12 F), static conditions P Outlet Max. Speed Q Outlet Flow Pressure A B Model Series r/min l/min (USgpm) ( ( L/min (USgpm) PVM18 18 32 (8.5) 28 (4) 2,8 (4) 4,5 (1.2) PVM2 18 35 (9.25) 23 (33) 2,8 (4) 4,5 (1.2) PVM45 18 76 (2) 28 (4) 1 (15) 4,5 (1.2) PVM5 18 87 (23) 23 (33) 1 (15) 4,5 (1.2) PVM57 18 12 (27) 28 (4) 3,5 (51) 14 (3.7) PVM63 18 113 (29) 23 (33) 7,4 (17) 7,6 (2.) PVM74 18 127 (33.5) 28 (4) 1,5 (22) 37 (9.8) PVM81 18 141 (37) 23 (33) 1,5 (22) 37 (9.8) PVM98 18 179 (47) 28 (4) 1,5 (22) 25 (6.6) PVM16 18 195 (51.5) 23 (33) 1,5 (22) 2 (5.3) PVM131 18 229 (6.5) 28 (4) 3,5 (51) 19 (5.) PVM141 18 238 (63) 23 (33) 3,5 (51) 14 (3.7) 12 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Control Options K outlet gage port + To load C outlet Mobil Pressure Cut-off Characteristics of Pressure Compensator Control at 93 C (2 F), static conditions. Q Change in Pressure A Change in Flow B Outlet Flow Outlet Pressure P Pressure Cut-off Characteristics of Pressure Compensator Control @ 93 C (2 F), static conditions P Outlet Rated Speed Q Outlet Flow Pressure A B Model Series r/min l/min (USgpm) ( ( L/min (USgpm) PVM18 28 42 (11) 28 (4) 2,8 (4) 4,5 (1.2) PVM2 28 52 (14) 23 (33) 2,8 (41) 4,5 (1.2) PVM45 26 115 (3) 28 (4) 1 (15) 4,5 (1.2) PVM5 26 125 (33) 23 (33) 1 (15) 4,5 (1.2) PVM57 25 14 (37) 28 (4) 3,5 (5) 14 (3.7) PVM63 25 159 (42) 23 (33) 7,4 (17) 11,4 (3.) PVM74 24 174 (46) 28 (4) 1,5 (2) 37 (9.8) PVM81 24 185 (49) 23 (33) 1,5 (22) 37 (9.8) PVM98 22 217 (57) 28 (4) 1,5 (2) 32 (8.4) PVM16 22 234 (62) 23 (33) 1,5 (22) 24 (6.33) PVM131 2 253 (67) 28 (4) 1, (15) 23 (6.) PVM141 2 258 (68) 23 (33) 7, (1) 14 (3.7) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 13

Control Options Load Sensing and Pressure Compensator Control Code B or C The pump will provide power matching of pump output to system load demand, maximizing efficiency and improving load metering characteristics of any directional control valve installed between the pump and the load. Load sensing ensures that the pump always provides only the amount of flow needed by the load. At the same time, the pump operating pressure adjusts to the actual load pressure plus a pressure differential required for the control action. When the system is not demanding power, the load sense control will operate in an energy-saving stand-by mode. Typically, the differential pressure is that between the pressure inlet and service port of a proportionally controlled directional valve, or a load sensing directional control valve. See the model code on page 4 for differential pressure settings for load sensing. If the load pressure exceeds the system pressure setting, the pressure compensator destrokes the pump. The load sensing line must be as short as possible and can also be used for remote control or unloading of the pump pressure. For remote control purposes, it is recommended that you contact your Eaton representative for the correct configuration of the control. Warning: The pressure compensator may be adjusted beyond the rated pressure of the pump. When adjusting the pressure limiter, install a -35 (-5 gage in the outlet gage port and limit the pressure setting to the continuous rated pressure for the pump displacement shown on page 7. F case drain K inlet gage port K outlet gage port Optional bleed-down orifice in Code B control.,4 mm (.16 in.) Orifice is plugged for no bleed down in control Code C. B inlet To load C outlet J load sense signal port 14 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Control Options Industrial Control Compensator Code E & F (Model 57-141 only) This pump is intended for use when multiple, remote, or electronically controlled compensating settings, with or without load sensing, are desired. With Pressure & Flow Compensator (E) Inlet Pressure compensation is obtained when an internal plug is removed, the load-sense signal port is kept plugged, and internal pilot pressure is applied to the spring chamber of the control spool. For pressure compensation with load sensing, the internal plug stays, the loadsense signal port is unplugged, and pilot pressure is externally applied. An external relief valve (not supplied) controls spring chamber pressure. The externally adjustable spring determines the differential pressure setting of the control. Outlet pressure is limited to the valve of the spring chamber (pressure port) pressure, plus control differential pressure. Spring chamber (pilot) pressure is separated from outlet pressure by an internal orifice. Outlet pressure shifts the spool when pressure drop across the orifice reaches the differential pressure setting, and the pump de-strokes. The relief valve can be mounted to an NFPA-D3/ISO 441-3 pad on the pump control, or remotely located via tapping and blanking plates installed on the pad. See Ordering Procedure, page 27, for more on valves and plates. The standard factory-set differential pressure setting of the pump control is 2 (29 and is not specified in the pump model number. Any other ordered differential pressure, within the control s adjustable pressure range of 17-35 (247-58, will be specified in the model number. Inlet To load To load Outlet Outlet Load sense signal port Inlet Outlet Load sense signal port To load Pressure Compensating Without Load Sensing (F) Inlet To load Outlet Load sense signal port Load sense signal port Pressure port Tank port Pressure port Tank port Pressure port Tank port Pressure port Tank port Case drain Case drain Case drain Case drain EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 15

Performance Industrial PVM18 Noise Level Noise dba Level dba Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 66 Typical Noise Levels at 18 and 12 r/min with 64 Petroleum 18 r/min Oil (1W) at 5 C (12 F) and 1. max. flow absolute ( psi gauge) Inlet 66 62 64 6 62 58 6 56 58 54 56 52 54 5 18 r/min max. flow 12 r/min max. flow 12 r/min max. flow 12 r/min min. flow 52 48 18 r/min min. flow 5 46 5 1 15 2 25 3 35 48 18 (7) r/min(15) (22) (29) 12 r/min (36) (44) (5) Sound pressure min. flowdata min. flow equivalent to NFPA. 46 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Sound pressure data equivalent to NFPA. Delivery and Efficiency at 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency at 18 r/min 5 C Volumetric (12 F) and Efficiency 1. absolute ( psi gauge) Inlet 1 9 Volumetric Efficiency 8 9 7 8 Efficiency Efficiency % % 6 7 5 6 4 (11) 4 5 4 (11) 3 (8) 3 4 3 (8) 2 (5) 2 3 2 (5) 1 2 1 (3) 1 (3) 1 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 Outlet 1 Pressure 15 2 25 ( 3 35 (7) (15) (22) (29) (36) (44) (5) Delivery Delivery l/min l/min (USgpm) (USgpm) Noise Level Noise dba Level dba Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 62 Typical Noise Levels at 15 and 1 r/min with 6 Petroleum Oil (1W) at 5 C (12 F) and 1. 15 r/minabsolute ( psi gauge) Inlet 62 58 max. flow 6 56 15 58 54 1 r/min max. flow 56 52 54 5 1 r/min max. flow 52 48 15 r/min min. flow 5 46 1 r/min 48 44 15 r/min min. flow 46 42 min. flow 5 1 15 2 25 3 35 1 r/min 44 (7) (15) (22) (29) (36) (44) (5) min. flow 42 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque and Power at 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 (885) Torque and Power at 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 9 (796) (885) Torque, 8 9 (78) (796) Torque, 7 8 (619) (78) 6 7 (531) (619) 5 6 (442) (531) 4 5 (354) (442) 3 4 (265) (354) 2 3 (177) (265) 21 (177) (88) Torque, 51 (7) (13) 1 (88) Cut-off 5 1 15 2 25 3 Torque, 5 (7) 35 (7) (15)(22)(29)(36) Cut-off (44)(5) 5 Outlet 1 Pressure 15 2 25 ( 3 35 (7) (15)(22)(29)(36)(44)(5) 16 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 Torque Torque Nm (in-lb) Nm (in-lb) Power, Power, 2 (27) 15 2 (2) (27) 1 15 (13) (2) Power Power kw (hp) kw (hp)

Performance Industrial PVM18 Torque Torque Nm Nm (in.lb.) (in.lb.) Efficiency % % Delivery and Efficiency at 15 r/min 5 C (12 Delivery F) and and 1. Efficiency absolute at 15 ( psi r/min gauge) Inlet 1 5 C Volumetric (12 F) and Efficiency 1. absolute ( psi gauge) Inlet 1 9 Volumetric Efficiency 8 9 7 8 6 7 5 6 4 5 3 4 2 3 1 2 3 (8) 2 3 (5) (8) 1 2 (3) (5) 1 1 (3) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 1 Outlet 15 Pressure 2 25 ( 3 35 (7) (15) (22) (29) (36) (44) (5) Torque and Power at 15 r/min 5 C (12 F) Torque and 1. and Power absolute at ( 15 psi r/min gauge) Inlet 1 (885) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 9 (796) (885) Torque, 8 9 (78) (796) Torque, 7 8 (619) (78) 6 7 (531) (619) 5 6 (442) (531) 5 4 (442) (354) Power, 2 (27) 3 4 (265) (354) Power, 15 2 (2) (27) 2 3 (177) (265) 1 15 (13) (2) 2 1 (177) (88) 5 1 (7) (13) 1 (88) 5 (7) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 1 Outlet Pressure 15 2 25 ( 3 35 (7) (15) (22) (29) (36) (44) (5) Delivery Delivery l/min l/min (USgpm) (USgpm) Power Power kw kw (hp) (hp) Delivery and Efficiency at 12 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency at 12 r/min 5 C Volumetric (12 F) and Efficiency 1. absolute ( psi gauge) Inlet 1 9 Volumetric Efficiency 8 9 7 8 6 7 5 6 4 5 3 4 3 (8) 2 3 2 3 (5) (8) 1 2 1 2 (3) (5) 1 1 (3) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 Outlet 1 Pressure 15 2 25 ( 3 35 (7) (15) (22) (29) (36) (44) (5) Efficiency Efficiency % % Torque Torque Nm Nm (in.lb.) (in.lb.) Torque and Power at 12 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 (885) Torque and Power at 12 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Torque, 9 (796) (885) Torque, 8 9 (78) (796) 7 8 (619) (78) 6 7 (531) (619) 5 6 (442) (531) 4 5 (354) (442) 2 (27) Power, 3 4 (265) (354) 15 2 (2) (27) Power, 2 3 (177) (265) 1 15 (13) (2) 2 1 (177) (88) 51 (7) (13) 1 (88) 5 1 15 2 25 3 (7) (15)(22)(29)(36)(44)(5) 35 5 (7) 5 Outlet 1 Pressure 15 2 25 ( 3 (7) (15)(22)(29)(36)(44)(5) 35 Delivery Delivery l/min l/min (USgpm) (USgpm) Power Power kw (hp) kw (hp) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 17

Performance Industrial PVM18 Efficiency Efficiency % % torque torque Nm Nm (in.lb.) (in.lb.) Delivery and Efficiency at 1 r/min 5 C (12 F) Delivery and and 1. Efficiency absolute at 1 ( psi r/min gauge) Inlet 1 5 C (12 F) and 1. absolute ( psi gauge) Inlet Volumetric Efficiency 1 9 Volumetric Efficiency 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 2 (5) 2 1 (5) (3) 1 1 (3) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 1 Outlet Pressure 15 2 25 ( 3 35 (7) (15) (22) (29) (36) (44) (5) Torque and Power at 1 r/min 5 C (12 F), Torque and 1. and Power absolute at 1 ( psi r/min gauge) Inlet 1 (885) 5 C (12 F), and 1. absolute ( psi gauge) Inlet 1 9 (885) (796) Torque, 9 Torque, 8 (796) (78) 8 7 (78) (619) 7 6 (619) (531) 6 5 (531) (442) 5 4 (442) (354) 2 (27) 4 3 (354) (265) 2 (27) Power, 15 (2) 3 (265) 2 (177) Power, 15 1 (2) (13) 2 1 (177) (88) 1 5 (7) (13) 1 (88) 5 (7) 5 1 15 2 25 3 (7) (15) (22) (29)(36) (44)(5) 35 5 1 15 2 25 3 (7) (15) (22) (29)(36) (44)(5) 35 Delivery Delivery l/min l/min (USgpm) (USgpm) Power Power kw kw (hp) (hp) Case Flow Versus Outlet Pressure at 18 r/min, Full Flow 5 C (12 F) and 1. absolute ( psi gauge) Inlet Case 1,4 Flow (.37) Versus Outlet Pressure at 18 r/min, Full Flow 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1,4 1,2 (.37) (.32) Case Flow l/min (USgpm) Case Flow l/min (USgpm) 1,2 1, (.32) (.26) 1,,8 (.26) (.21),8,6 (.21) (.16),6,4 (.16) (.11),4,2 (.11) (.5),2 (.5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 1 Outlet Pressure 15 2 25 ( 3 35 (7) (15) (22) (29) (36) (44) (5) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet Case 5 (1.32) Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet Case Flow l/min (USgpm) Case Flow l/min (USgpm) 5 (1.32) 4 (1.6) 4 (1.6) 3 (.79) 3 (.79) 2 (.53) 2 (.53) 1 (.26) 1 (.26) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 1 Outlet 15 Pressure 2 25 ( 3 35 (7) (15) (22) (29) (36) (44) (5) 18 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Efficiency Efficiency % % Delivery Delivery l/min l/min (USgpm) (USgpm) Torque Torque Nm Nm (in.lb.) (in.lb.) Performance Mobile PVM18 Noise Noise Level Level dba dba Typical Noise Levels Petroleum Oil (1W) at 93 C (2 F), 1. Typical absolute Noise ( psi Levels gauge) Inlet (Sound Petroleum pressure Oil (1W) data equivalent at 93 C (2 F), to NFPA) 76 1. absolute ( psi gauge) Inlet 28 (Sound r/min pressure data equivalent to NFPA) 76 72 Max. Flow 28 r/min 68 72 Max. Flow 68 64 64 6 28 r/min Min. Flow 56 6 28 r/min Min. Flow 6 r/min 56 52 Max. Flow 6 r/min 48 52 Max. Flow 48 6 r/min 44 Min. Flow 6 r/min 4 44 Min. 5 1 (7) (15)(22) 15 Flow 2 25 3 35 4 (29) (36) (44)(5) 5 Outlet 1 Pressure ( (7) (15)(22) 15 2 25 3 35 (29) (36) (44)(5) Versus Speed at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 95 Versus Speed at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 95 9 9 1 (15 85 1 (15 15 (22 85 2 15 (29 (22 8 2 8 (29 25 (36 75 25 (36 28 75 (4 28 32 (4 (46 7 32 5 (46 1 15 2 25 3 7 Speed r/min 5 1 15 2 25 3 Speed r/min Delivery Delivery and and Case Case Flow Flow Versus Versus Speed Speed @ 93 C 93 C (2 F), (2 F), full full flow flow and and 1. 1. absolute absolute ( ( gauge gauge Inlet Inlet 5 5 (13.2) (13.2) 45 45 (11.9) (11.9) 4 4 (1.6) (1.6) 35 35 (9.2) (9.2) 3 3 (7.9) (7.9) 25 25 (5.3) (5.3) 25 25 (365 (365, Delivery, Delivery 25 25 (36 (36, Delivery, Delivery 2 2 (5.3) (5.3) 4, 4, (1.1) (1.1) 15 15 (4.) (4.) 3, 3, (.8) 25 (.8) 25 (36 (36,, Case Case flow 1 1 (2.6) flow (2.6) 2, 2, (.5) (.5) 5 5 (1.3) (1.3) 1, 1, (.3) 25 (.3) 25 (365 (365,, Case Case flow flow 5 5 1 1 15 15 2 2 25 Speed 25 3 3 Speed r/min r/min Torque Torque Versus Versus Speed Speed @ 93 C 93 C (2 F), (2 F), full full flow flow and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) inlet inlet 11 11 (973) (973) 1 1 (885) (885) 9 9 (796) (796) 8 8 (78) (78) 7 7 (619) (619) 6 6 (531) (531) 32 32 (46 (46 28 28 (4 (4 25 25 (36 (36 2 2 (29 (29 5 5 (442) (442) 15 15 (22 (22 4 4 (354) (354) 3 3 (265) (265) 1 1 (15 (15 2 2 (177) (177) 1 1 (88) (88) 25 25 (365 (365 5 5 1 1 15 Speed 15 2 2 Speed r/min r/min 25 25 3 3 Case Case Flow Flow l/min l/min (USgpm) (USgpm) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 19

Torque - Nm (in.lb.) Case Flow (l/min (USgpm) Torque - Nm (in.lb.) Case Flow (l/min (USgpm) Performance Mobile PVM18 Power @ Full Flow kw (hp) 28 (37.5) 26 (34.9) 24 (32.2) 22 (29.5) 2 (26.8) 18 (24.1) 16 (21.4) 14 (18.8) 12 (16.1) 1 (13.4) 8 (1.7) 6 (8.) 4 (5.4) 2 (2.7) 3 (27) Power Versus Speed @ 93 C (2 F), full flow and 1. absolute ( psi gauge) inlet 28 (37.5) Power Versus Speed 32 @ 93 C (2 F), full flow and 1. absolute ( psi gauge) 26 inlet (34.9) (46 24 (32.2) 28 32 (4 22 (29.5) (46 25 2 (26.8) 28 (36 (4 18 (24.1) 2 25 16 (21.4) (29 (36 14 (18.8) 2 15 12 (16.1) (29 (22 1 (13.4) 1 8 (1.7) 15 (15 (22 6 (8.) 4 (5.4) 1 (15 25 2 (2.7) (365 5 1 15 2 25 3 25 Speed r/min (365 Power @ Full Flow kw (hp) Torque and Case Flow Versus Speed 5 1 15 2 25 3 @ 93 C (2 F), load sense standby Speed r/min and 1. absolute ( psi gauge) inlet 3 (27) Torque and Case Flow Versus Speed @ 93 C (2 F), load sense standby and 1. absolute ( psi gauge) inlet 2 (18) 2 (3 differential, Torque 2 (3 differential, 1 (9) Case Flow 5 (1.32) 11 (16 4 (1.6) differential, 3 (.79) Torque 11 (16 differential, 2 (.53) Case Flow 1 (.26) 5 1 15 2 25 3 Speed r/min Torque and Case Flow Versus Speed @ 93 C (2 F), cut-off and 1. absolute 2 (18) ( psi gauge) inlet 5 (442) 45 (398) 2 (3 28 (4 differential, Torque 4 (354) Torque 2 (3 differential, 1 (9) 35 (31) Case Flow 5 (1.32) 11 (16 4 (1.6) 3 (265) differential, 3 (.79) Torque 11 (16 25 (221) differential, 2 (.53) 15 (22 Case Flow 1 (.26) 2 (177) 5 Torque 1 15 2 25 3 15 (135) Speed r/min 9 (2.4) 28 (4, Case Flow 1 (88) 6 (1.6) 5 (45) 15 (22 3 (.8) Case Flow 5 1 15 2 25 Speed r/min 2 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Performance Industrial PVM2 Noise Level Noise dba Level dba Noise Level Noise dba Level dba 64 62 6 64 58 62 56 6 Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet Typical Noise Levels at 18 and 12 r/min 18 r/min Max. with Petroleum Flow Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 18 12 r/min r/min Max. Max. Flow Flow 54 58 12 r/min Max. Flow 52 56 18 r/min 5 54 Min. Flow 48 52 46 18 r/min 5 Min. Flow 44 48 12 r/min 42 46 Min. Flow 4 44 5 1 15 2 25 (7) (15) (22) 12 (29) r/min 42 (36) Outlet Pressure Min. ( Flow 4 Typical 5 Noise Levels 1 at 15 and 1 2 r/min 25 with (7) Petroleum (15) Oil (1W) (22) at 5 C (29) (12 F) (36) and 1. Outlet absolute Pressure ( psi gauge) ( Inlet 64 Typical Noise Levels at 15 and 1 r/min 62 with Petroleum Oil (1W) at 5 C (12 F) 15 and 1. r/min absolute ( psi gauge) Inlet 6 64 Max. Flow 58 62 15 56 6 Max. 1 Flowr/min 54 Max. Flow 58 52 56 1 r/min 5 54 Max. Flow 15 r/min 48 52 Min. Flow 46 5 44 15 r/min 1 r/min 48 Min. Flow Min. Flow 42 46 4 44 1 r/min 5 1 15 Min. Flow 2 25 42 (7) (15) (22) (29) (36) 4 Sound pressure 5 data 1 15 2 25 equivalent (7) to NFPA (15) (22) (29) (36) Sound pressure data equivalent to NFPA Efficiency Efficiency % % torque torque Nm (in.lb.) Nm (in.lb.) Delivery and Efficiency at 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency at 18 r/min, 5 C (12 F), 1 and Volumetric 1. Efficiency absolute ( psi gauge) Inlet 1 9 1 Volumetric Efficiency 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 5 1 15 2 (7) (15) (22) (29) 5 Outlet Pressure 1 15 ( 2 (7) (15) (22) (29) 5 (13) 5 4 (13) (11) 4 3 (11) (8) 3 2 (8) (5) 2 1 (5) (3) 1 (3) 25 (36) 25 (36) Torque and Power at 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet Torque and Power at 18 r/min, 5 C (12 F), 12 (162) and 1. absolute ( psi gauge) Inlet 12 11 (162) (973) 11 1 (973) (885) 1 9 (885) (796) 9 8 (796) (78) 8 7 (78) (619) 7 6 (619) (531) Torque, 6 5 (531) (442) Torque, 25 (34) 5 4 (442) (354) 2 25 (27) (34) Power, 4 3 (354) (265) 15 2 (2) (27) Power, 3 2 (265) (177) Torque, 1 15 (13) (2) 21 (177) (88) Cut off 5 Torque, 1 (7) (13) 1 (88) Cut off 5 (7) 5 1 15 2 25 (7) (15) (22) (29) (36) Outlet 5 Pressure 1 15 ( 2 25 (7) (15) (22) (29) (36) Delivery Delivery l/min l/min (USgpm) (USgpm) Power Power kw (hp) kw (hp) Efficiency Efficiency % % EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 21

Performance Industrial PVM2 Delivery and Efficiency at 15 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet Delivery and Efficiency at 15 r/min, 5 C (12 F), 1 Volumetric and 1. Efficiency absolute ( psi gauge) Inlet 91 Volumetric Efficiency 89 78 Efficiency % Efficiency % 67 56 45 34 23 12 1 5 (13) 45 (11) (13) 34 (8)(11) 23 (5)(8) 12 (3)(5) 1 (3) 5 1 15 2 25 (7) (15) (22) (29) (36) 5 Outlet Pressure 1 15 ( 2 25 (7) (15) (22) (29) (36) Delivery and and Efficiency at at 12 12 r/min, r/min, 5 C 5 C (12 F), and and 1. 1. absolute ( ( psi psi gauge) Inlet Inlet 1 1 Volumetric Efficiency 9 9 8 8 7 7 Efficiency % Efficiency 6 6 5 5 4 4 3 3 2 2 1 1 5 5 (13) (13) 4 4 (11) (11) 3 3 (8) (8) flow) 2 2 (5) (5) 1 1 (3) (3) 5 5 1 1 15 15 2 2 25 25 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) Outlet Outlet Pressure ( ( Delivery l/min (USgpm) Deliver a 1 1 V 9 9 8 8 7 7 Efficiency % Efficiency 6 6 5 5 4 4 3 3 2 2 1 1 Power kw (hp) Torque and Power at 15 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet Torque and Power at 15 r/min, 5 C (12 F), 12 (162) and 1. absolute ( psi gauge) Inlet 11 12 (973) (162) torque Nm (in.lb.) torque Nm (in.lb.) 111 (885) (973) 91 (796) (885) 89 (78) (796) 78 (619) (78) 67 (531) (619) Torque, 56 (442) (531) Torque, 25 (34) 45 (354) (442) 225 (27) (34) 34 (265) (354) Power, 15 (2) (27) 23 (177) (265) Power, 115 (13) (2) 12 (88) (177) 5 (7) 1 (13) 1 (88) 5 (7) 5 1 15 2 25 (7) (15) (22) (29) (36) 5 1 15 2 25 Outlet (7) Pressure (15) (22) ( (29) (36) Power kw (hp) Power kw (hp) torque Nm (in.lb.) torque Nm (in.lb.) Torque and and Power Power at at 12 12 r/min, r/min, 5 C 5 C (12 F), and and 1. 1. absolute ( ( psi psi gauge) Inlet Inlet 12 12 (162) (162) 11 11 (973) (973) 1 1 (885) (885) 9 9 (796) (796) 8 8 (78) (78) 7 7 (619) (619) 6 6 (531) (531) Torque, Full 5 5 (442) Stroke (442) 25 25 (34) (34) 4 4 (354) (354) 2 2 (27) (27) Power, 3 3 (265) (265) Full 15 Stroke 15 (2) (2) 2 2 (177) (177) 1 1 (13) (13) 1 1 (88) (88) 55 (7) (7) 5 5 1 1 15 15 2 2 25 25 (7) (7)(15) (15)(22) (22)(29) (29)(36) (36) Outlet Outlet Pressure ( ( Power kw (hp) Power kw (hp) torque Nm (in.lb.) torque Nm (in.lb.) InI 12 111 11 9 8 7 6 5 4 3 2 22 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Performance Industrial PVM2 13) 11) 8) 5) 3) Efficiency % Delivery Delivery and and Efficiency Efficiency at 1 at 1 r/min, r/min, 5 C 5 C (12 F), (12 F), and and 1. 1. absolute absolute ( psi ( gauge) psi gauge) Inlet Inlet 1 1 Volumetric Volumetric Efficiency Efficiency 9 9 Overall Efficiency 8 8 7 7 6 6 5 5 4 4 3 3 2 2 Delivery Delivery (effective (effective flow) flow) 1 1 Efficiency % 5 (13) 5 (13) 4 (11) 4 (11) 3 (8) 3 (8) 2 (5) 2 (5) 1 (3) 1 (3) 5 5 1 1 15 15 2 2 25 25 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) Outlet Outlet Pressure Pressure ( ( Case Flow l/min (USgpm) Case Flow versus Outlet Pressure at 18 r/min, Full Flow, Case Flow versus Outlet Pressure at 18 r/min, Full Flow, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 5 C (12 F), and 1. absolute ( psi gauge) Inlet 2.5 (.66) 2.5 (.66) 2.3 (.59) 2.3 (.59) 2. (.53) 2. (.53) 1.8 (.46) 1.8 (.46) 1.5 (.4) 1.5 (.4) 1.3 (.33) 1.3 (.33) 1. (.26) 1. (.26).8 (.2).8 (.2).5 (.13).5 (.13).3 (.7).3 (.7) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Outlet Pressure ( F), Torque Torque and and Power Power at 1 at 1 r/min, r/min, 5 C 5 C (12 F), (12 F), and and 1. 1. absolute absolute ( psi ( gauge) psi gauge) Inlet Inlet 12 (162) 12 (162) 11 (973) 11 (973) 1 (885) 1 (885) (34) (27) (2) (13) 7) Power kw (hp) Power kw (hp) torque Nm (in.lb.) 9 (796) 9 (796) torque Nm (in.lb.) 8 (78) 8 (78) 7 (619) 7 (619) 6 (531) 6 (531) Torque, Torque, 5 (442) 5 (442) 25 (34) 25 (34) 4 (354) 4 (354) 2 (27) 2 (27) 3 (265) 3 (265) Power, Power, 15 (2) 15 (2) 2 (177) 2 (177) 1 (13) 1 (13) 1 (88) 1 (88) 5 (7) 5 (7) 5 51 115 152 225 25 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) Outlet Outlet Pressure Pressure ( ( Power kw (hp) Case Flow l/min (USgpm) Power kw (hp) Case Flow versus Outlet Pressure at Cutoff, 18 r/min, Case Flow versus Outlet Pressure at Cutoff, 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 5 C (12 F), and 1. absolute ( psi gauge) Inlet 1 (2.64) 1 (2.64) 9 (2.38) (2.38) 8 (2.11) (2.11) 7 (1.85) (1.85) 6 (1.59) (1.59) 5 (1.32) (1.32) 4 (1.6) (1.6) 3 (.79) (.79) 2 (.53) (.53) 1 (.26) (.26) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Outlet Pressure ( EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 23

Performance Mobile PVM2 Noise Level dba Noise Level dba 77 77 74 74 71 71 68 68 65 65 62 62 59 59 56 56 53 53 5 5 47 47 44 44 Typical Noise Levels at at 28 28 & & 6 6 r/min with with Petroleum Oil Oil (1W) at at 93 C 93 C (2 F) and and 1. 1. absolute ( ( psi psi gauge) Inlet Inlet 41 41 5 5 Sound pressure data data(7) equivalent to to NFPA. 28 28 r/min r/min Typical Noise Levels at 28 & 6 r/min with Petroleum Oil (1W) max. max. flow flow at 93 C (2 F) and 1. absolute ( psi gauge) Inlet Noise Level dba 77 74 71 68 65 62 28 r/min max. flow 28 28 r/min r/min min. min. flow flow 28 r/min min. flow 59 6 6 r/min r/min max. max. flow flow56 6 6 r/min r/min 53 min. min. flow flow 5 6 r/min max. flow 1 1 47 15 15 2 2 6 r/min min. 25 25 flow (15) 44 (22) (29) (36) Outlet Pressure ( ( 41 5 1 15 2 25 (7) (15) (22) (29) (36) Sound pressure data equivalent to NFPA. versus Speed Delivery and and Case Flow Flow versus Speed at at 93 C 93 C (2 F), at at 93 C 93 C (2 F) and and 1. 1. absolute ( ( psi psi gauge) inlet inlet Full Full Flow Flow 1. 1. absolute ( ( psi psi gauge) inlet inlet 1 1 6 6 (15.9) (15.9) versus Speed 95 95 55 55 (14.5) (14.5) 15 15 at 93 C (2 F) and 1. absolute ( psi gauge) inlet (22 1 5 5 (13.2) (13.2) 6 (15.9) 9 9 21 21 (3 45 45 (11.9) (11.9) 95 55 (14.5) 5 5 (725 (725 85 85 1 1 (15 4 15 4 (1.6) (1.6) (22 Delivery 5 (13.2) 8 8 9 21 (3 35 35 (9.2) (9.2) 45 (11.9) 5 5 (7 (7 21 21 (3 75 85 3 3 (7.9) (7.9) 75 1 (15 Delivery 4 (1.6) 23 23 (33 25 25 (6.6) (6.6) 8 35 (9.2) 7 7 52 (5.3) (5.3) (7 3 (7.9) 4 4 (1.6) 65 65 75 15 15 (4.) (4.) 23 (33 25 (6.6) 3 3 (.79) 6 6 7 1 1 (2.6) (2.6) 21 21 (3 Case Flow 2 Flow (5.3) 2 2 (.53) 55 55 65 5 (1.3) 5 (1.3) 5 5 (725 (725 Case Flow Flow15 (4.) 1 1 (.26) 6 5 5 1 (2.6) 5 5 1 1 15 15 2 2 25 25 3 3 5 5 1 115 152 225 253 3 55 5 (1.3) Speed r/min r/min Speed (r/min) (%) (%) (%) 5 5 1 15 2 25 Speed r/min 3 Delivery and Case Flow v Full Flow 1. abs Case Flow l/min (USgpm) Case Flow l/min (USgpm) 5 b 21 b 5 5 1 S 24 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Torque Nm (lb.in.) Torque Torque Nm Nm (lb.in.) (lb.in.) Torque Nm (lb.in.) Power kw (hp) Power Power kw kw (hp) (hp) Power kw (hp) Performance Mobile PVM2 Torque versus Speed at 93 C (2 F), Power versus Speed at 93 C (2 F), Full Flow Torque and Torque versus 1. versus Speed absolute Speed at 93 C ( psi at (2 F), 93 C gauge) (2 F), Inlet Full Flow Power and Power versus 1. versus Speed absolute Speed at 93 C ( at psi (2 F), 93 C gauge) (2 F), Inlet Full Flow Full and Flow 1. and 1. absolute absolute ( psi ( gauge) psi gauge) Inlet Inlet Full Flow Full and Flow 1. and 1. absolute absolute ( psi ( gauge) psi gauge) Inlet Inlet 11 (973) 24 (32) 11 (973) 11 (973) 23 (33 1 (885) 24 (32) 22 (3) 24 (32) 23 23 (33 (33 1 (885) 1 (885) 22 (3) 9 (796) 2 (27) 22 (3) 21 (3 9 (796) 9 (796) 23 (33 2 (27) 2 (27) 8 (78) 18 (24) 21 (3 23 23 (33 (33 21 (3 8 (78) 8 (78) 18 (24) 18 (24) 7 (619) 16 (21) 21 (3 7 (619) 7 (619) 16 14 (21) (19) 16 (21) 6 (531) 21 21 (3 (3 15 (22 15 (22 14 (19) 6 (531) 14 (19) 6 (531) 12 (16) 15 (22 5 (442) 15 15 (22 (22 15 (22 12 (16) 12 (16) 5 (442) 5 (442) 1 (13) 4 (354) 1 (15 1 (15 1 (13) 1 (13) 4 (354) 4 (354) 1 1 (15 (15 8 (11) 1 1 (15 (15 3 (265) 8 (11) 8 (11) 3 (265) 3 (265) 5 (725 6 (8) 2 (177) 5 (725 6 (8) 5 (725 4 (5) 6 (8) 5 (725 2 (177) 2 (177) 4 (5) 5 (725 4 (5) 5 (725 1 (88) 2 (3) 1 (88) 1 (88) 2 (3) 2 (3) 5 1 15 2 25 3 5 1 15 2 25 3 5 5 1 1 15 Speed 15 2 (r/min) 2 25 25 3 3 5 1 5 1 Speed 15 15 (r/min) 2 2 25 25 3 3 Speed Speed (r/min) (r/min) Speed Speed (r/min) (r/min) Torque Nm (lb.in.) Torque Torque Nm Nm (lb.in.) (lb.in.) Torque Nm (lb.in.) Torque and Case Flow versus Speed at 93 C Torque (2 F), Torque and Load Case and Sense Case Flow Standby versus Flow versus Speed and 1. Speed at at 93 C (2 F), 93 C (2 F), absolute Load Load Sense ( psi Sense Standby gauge) Standby Inlet 1. and 1. 3.2 (28) absolute absolute ( psi ( gauge) psi gauge) Inlet Inlet 3.23. (28) (27) 3.2 (28) 3.2.8 (27) (25) 3. (27) 2.8 (25) 2 (29 diff. 2.6 (23) 2.8 (25) 2 (29 diff. 2.6 (23) 2 Torque (29 diff. 2.4 (21) 2.6 (23) Torque Torque 2.42.2 (21) (19) 2.4 (21) 2.2 (19) 2 (18) 2.2 (19) 11 (16 diff. 21.8 (18) (16) 2 (18) 11 11 (16 Torque (16 diff. diff. 1.81.6 (16) (14) 1.8 (16) Torque Torque Case Flow 1.6 (14) 1.6 (14) Case l/min Flow 1.4 (12) Case Flow l/min (USgpm) 1.41.2 (12) (11) l/min 1.4 (12) (USgpm) (USgpm) 1.2 (11) 1 1.2 (9) (11) 5. (1.32) 1 (9).8 (7) 1 (9) 5.4. (1.32) 5. (1.6) (1.32) 11 (16 diff..8 (7).6 (5) 4. (1.6).8 (7) 11 Case (16 diff. 4. (1.6) 11 Flow 3. (.79) (16 diff..6 (5).6 (5) Case Flow 2 (29 diff..4 (4) Case Flow 3.2. (.79) 3. (.53) (.79) 2 Case (29 diff..4 (4) 2 Flow.2 (2) (29.4 (4) 2. diff. 1. (.53) 2. (.26) (.53) Case Flow Case Flow.2 (2).2 (2) 1. (.26) 1. (.26) 5 1 15 2 25 3 5 1 5 1 Speed 15 15 2 (r/min) 2 25 25 3 3 Speed Speed (r/min) (r/min) Torque and Case Flow versus Speed at 93 C Torque (2 F), Torque and Case Pressure and Case Flow Limit versus Flow Cut-off versus Speed and Speed at 93 C at 1. (2 F), 93 C absolute (2 F), Pressure Pressure ( psi Limit gauge) Limit Cut-off Inlet Cut-off and and 3 (265) 1. 1. absolute absolute ( psi ( gauge) psi gauge) Inlet Inlet 3 (265) 3 (265) 21 (3 24 (212) 21 21 Torque (3 (3 24 (212) 24 (212) Torque Torque 21 (186) 21 (186) 21 (186) 18 (159) 18 (159) 18 (159) 15 (133) Case 15 (133) 15 (133) 15 Case Flow l/min 12 (16) 15 (22 Case 15 Flow (USgpm) l/min Flow l/min 12 (16) 12 (16) (22 (22 Torque 9 (8) (USgpm) (USgpm) Torque Torque 9 (2.4) 9 (8) 9 (8) 9 (2.4) 9 (2.4) 6 (53) 21 (3 Case Flow 6 (1.6) 6 (53) 6 (53) 21 21 (3 (3 Case Flow Case Flow 6 (1.6) 6 (1.6) 3 (27) 15 (22 Case Flow 3 (.8) 3 (27) 3 (27) 15 15 (22 (22 Case Flow Case Flow 3 (.8) 3 (.8) 5 1 15 2 25 3 5 5 1 Speed 1 15 (r/min) 15 2 2 25 25 3 3 Speed Speed (r/min) (r/min) (239) (239) (239) (lb.in.)27 (lb.in.)27 (lb.in.)27 (lb.in.)27 Torque Nm Torque Nm Torque Nm EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 25

Performance Industrial PVM45 Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) Delivery and Efficiency at 18 r/min Typical and Noise 1. Levels absolute at 18 ( psi and gauge) 12 Inlet r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 72 with Petroleum Oil (1W) at 5 C (12 F) 1 and 1. absolute ( psi gauge) Inlet 727 Volumetric Efficiency 18 r/min 9 Delivery and Efficiency at 18 r/min 768 Max. Flow 5 C (12 F) and 1. absolute ( psi gauge) Inlet 18 r/min 8 1 6866 Max. Flow 7 Volumetric Efficiency 9 6664 62 18 r/min 64 6 Min. Flow 8 62618 r/min Min. Flow 5 7 658 12 r/min Max. Flow 4 6 12 (27) 5856 12 r/min Max. Flow 3 5 76 (2) 54 12 r/min 56 Min. Flow 2 4 49 (13) 12 (27) 5452 12 r/min Min. Flow 1 3 27 (7) 525 76 (2) 548 2 5 1 (7) (15)(22) 15 49 (13) 5 1 15 2 25 3 2 25 3 35 48 (7) (15) (22) (29) (36) (44) (29) (36) (44) (5) 1 27 (7) Sound pressure 5 data Outlet 1 Pressure 15 2 ( 25 3 equivalent to (7) NFPA (15) (22) (29) (36) (44) 5 Torque 1 and Power at 18 r/min 5 C (12 F) (7) and (15) 15 Sound pressure data 2 25 3 35 equivalent to NFPA 1. (22) absolute (29) ( psi (36) gauge) (44) Inlet (5) Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) 24 (2125) Typical and Noise 1. Levels absolute at 15 ( psi and gauge) 1 Inlet r/min 72 with Petroleum Oil (1W) at 5 C (12 F) 21 (186) Torque and Power at 18 r/min and 1. absolute ( psi gauge) Inlet 5 C (12 F) and 1. Torque, absolute ( psi gauge) Inlet 727 15 r/min 24 (2125) Max. Flow 15 r/min 18 (1595) 7 15 r/min Min. Flow 68 Max. Flow 15 1 r/min r/min 21 (186) Power, Min. Max. Flow 15 (1325) Torque, 5 (67) 68 Flow 66 1 r/min 18 (1595) Max. Flow 66 12 (16) 4 (54) 64 Power, 15 (1325) 5 (67) 6462 9 (795) 3 (4) 1 r/min 626 Min. Flow 12 (16) 4 (54) 1 r/min 6 (53) Torque, 2 (27) 658 Min. Flow 9 (795) Cut-off 3 (4) 3 (265) 1 (13) 5856 6 (53) Torque, 2 (27) 56 54 5 1 15 2 Cut-off 25 3 35 3 (265) (7) (15) (22) (29) (36) (44) (5) 1 (13) 5452 5 1 15 2 25 3 52 (7) (15) (22) (29) (36) (44) 5 Outlet 1 Pressure 15 2 ( 25 3 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (7) (15) (22) (29) (36) (44) (5) Noise Level dba Noise Level dba Noise Level dba Noise Level dba torque Nm (in.lb.) torque Nm (in.lb.) Efficiency % Efficiency % Power kw (hp) Power kw (hp) 26 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Power kw (hp) Power kw (hp) Performance Industrial PVM45 torque Nm (in.lb.) torque Nm (in.lb.) Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. Overall absolute Efficiency ( psi gauge) Inlet 81 Volumetric Efficiency 79 68 57 46 35 12 (27) 76 (2) 24 12 49 (13) (27) 13 76 27 (2) (7) 2 49 (13) 5 1 15 2 25 3 35 1 (7) (15) (22) (29)(36) (44) (5) 27 (7) 5 1 15 2 25 3 35 (7) Torque (15) and (22) Power (29) at (36) 15 (44) r/min (5) 5 C (12 F) and Outlet 1. Pressure absolute (( gauge) Inlet 24 (2125) 21 (186) Torque and Power at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 24 (2125) 18 (1595) Torque, 21 (186) 15 (1325) 18 (1595) Torque, 12 (16) 4 (54) Power, 15 (1325) 9 (795) 3 (4) 12 (16) 4 (54) Power, 6 (53) 2 (27) 9 (795) 3 (4) 3 (265) 6 (53) 1 (13) 2 (27) 3 (265) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 1 (13) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Efficiency % Efficiency % Delivery Delivery l/min (USgpm) l/min (USgpm) Power kw Power (hp) kw (hp) Delivery and Efficiency at 12 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Volumetric Delivery Efficiency and Efficiency at 12 r/min 9 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 8Volumetric Efficiency 9 7 8 6 7 5 6 4 76 (2) 5 3 57 (15) 4 76 (2) 2 38 (1) 3 57 (15) 1 19 (5) 2 38 (1) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44)(5) 35 1 19 (5) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) 35 (5) Torque Outlet Pressure and Power at ( 12 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 24 (2125) Torque and Power at 12 r/min 21 (186) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 24 (2125) Torque, 18 (1595) 21 (186) 15 (1325) Torque, 18 (1595) 12 (16) 15 (1325) Power, 9 (795) 3 (4) 12 (16) Power, 6 (53) 2 (27) 9 (795) 3 (4) 3 (265) 1 (13) 6 (53) 2 (27) 3 (265) 5 1 15 2 25 3 35 1 (13) (7) (15) (22) (29) (36)(44) (5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36)(44) (5) Efficiency % Efficiency % EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 27

Case Flow Case Flow l/min (USgpm) l/min (USgpm) Case Flow Case Flow l/min (USgpm) l/min (USgpm) Performance Industrial PVM45 Torque Torque Nm (in.lb.) Nm (in.lb.) Delivery and Efficiency at 1 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency at 1 r/min 95 C (12 F) and Overall 1. Efficiency absolute ( psi gauge) Inlet 1 Volumetric Efficiency 8 9 7 Volumetric Efficiency 8 6 7 5 6 4 76 (2) 5 3 57 (15) 4 76 (2) 2 38 (1) 3 1 57 (15) 19 (5) 2 38 (1) 5 1 15 2 25 3 35 1 (7) (15) (22) (29) (36) (44) (5) 19 (5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque Outlet and Pressure Power at 1 ( r/min 5 C (12 F), and 1. absolute ( psi gauge) Inlet 24 (2125) Torque and Power at 1 r/min 21 (186) 5 C (12 F), and 1. absolute ( psi gauge) Inlet 24 (2125) Torque, 18 (1595) 21 (186) Torque, 15 (1325) 18 (1595) 12 (16) 15 (1325) 9 (795) Power, 3 (4) 12 (16) 6 (53) 2 (27) 9 (795) Power, 3 (4) 3 (265) 1 (13) 6 (53) 2 (27) 3 (265) 5 1 15 2 25 3 35 1 (13) (7) (15) (22) (29) (36) (44)(5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Efficiency Efficiency % % Power kw (hp) Power kw (hp) Case Flow Versus Outlet Pressure at 18 r/min, Full Flow 5 C (12 F) and 1. absolute ( psi gauge) Inlet 2, (.53) Case Flow Versus Outlet Pressure at 18 r/min, Full Flow 1,8 (.47) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 2, (.53) 1,6 (.42) 1,8 (.47) 1,4 (.37) 1,6 (.42) 1,2 (.32) 1,4 (.37) 1, (.26) 1,2 (.32),8 (.21) 1, (.26),6 (.16),8 (.21),4 (.1),6 (.16),2 (.5),4 (.1),2 (.5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44)(5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44)(5) Case Flow Versus Outlet Outlet Pressure Pressure at ( Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 6 (1.59) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 65 (1.59) (1.32) 54 (1.32) (1.6) 43 (1.6) (.79) 3 2 (.79) (.53) 21 (.53) (.26) 1 (.26) 5 1 15 2 25 3 35 (7) (15) (22) (29)(36) (44)(5) 5 1 15 2 25 3 35 (7) (15) (22) (29)(36) (44)(5) 28 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Case Flow l/min (USgpm) Case Flow l/min (USgpm) Performance Mobile PVM45 Noise Noise Level Level dba dba Efficiency Efficiency % % Typical Noise Levels Petroleum Oil (1W) at 93 C (2 F), Typical Noise Levels 1. absolute ( psi gauge) Inlet Petroleum Oil (1W) at 93 C (2 F), (Sound pressure data equivalent to NFPA) 82 1. absolute ( psi gauge) Inlet 26 (Sound r/min pressure data equivalent to NFPA) 82 Max. Flow 78 26 r/min Max. Flow 78 74 74 7 6 r/min 7 26 r/min Min. Flow 66 Min. Flow 6 r/min 26 r/min Min. Flow 66 Min. Flow 62 62 58 6 r/min Max. Flow 58 6 r/min 54 Max. Flow 54 5 5 1 15 2 25 3 5 (7) (15) (22) (29) (36) (44) 5 Outlet 1Pressure 15 2 ( 25 3 (7) (15) (22) (29) (36) (44) Versus Speed at 93 C (2 F) and 1. absolute ( psi gauge) Inlet Versus Speed 95 at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 95 1 (15 9 1 (15 9 15 (22 15 85 (22 5 2 (7 85 5 (29 2 (7 8 (29 8 25 (36 75 25 17 (36 (25 75 28 17 (4 28 (25 7 (4 5 1 15 2 25 3 7 5 Speed r/min 1 15 2 25 3 Speed r/min Delivery and Case Flow Versus Speed @ 93 C (2 F), full flow and 1. absolute ( gauge Inlet 12 (32) 11 (29) Delivery and 5 Case (7 Flow, Versus Speed @ 93 C (2 F), full flow 1 (26) Delivery and 1. absolute ( gauge Inlet 12 (32) 9 (24) 11 (29) 5 (7, 28 (4, 8 (21) 1 (26) Delivery Delivery 7 (18) 9 (24) 6 (16) 28 (4, 8 (21) Delivery 2,5 (.7) 5 (13) 7 (18) 4 (11) 28 (4, 2, (.5) 6 (16) Case flow 3 (8) 1,5 2,5 (.4) (.7) 5 (13) 2 (5) 1, (.3) 4 (11) 5 28 (7 (4,, 2, (.5) 1 (3) Case Case flow flow,5 (.1) 3 (8) 1,5 (.4) 2 (5) 1, (.3) 5 1 15 2 25 3 Speed r/min5 (7, 1 (3) Case flow,5 (.1) 5 Torque 1 Versus 15 Speed 2 25 3 @ 93 C (2 F), full flow and Speed 1. r/min absolute ( psi gauge) inlet 225 (1991) 21 (1858) 28 (4 Torque Versus Speed 195 (1726) @ 93 C (2 F), full flow and 1. absolute ( psi gauge) inlet 25 (36 18225 (1593) (1991) 165 21 (146) (1858) 28 (4 2 (29 15 195 (1327) (1726) 25 (36 135 18 (1195) (1593) 15 (22 12 165 (162) (146) 2 (29 15 15 (929) (1327) 1 (15 9 135 (796) (1195) 15 (22 75 12 (664) (162) 615 (531) (929) 5 1 (7 (15 45 9 (398) (796) 25 (365 3 75 (265) (664) 17 (25 6 (531) 5 (7 45 (398) 5 1 15 2 25 25 (365 3 Speed r/min 3 (265) 17 (25 5 1 15 2 25 3 Speed r/min EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 29

Performance Mobile PVM45 Power @ Full Power Flow @ kw Full (hp) Flow kw (hp) Case Flow l/min Case (USgpm) Flow l/min (USgpm) Case Flow l/min Case (USgpm) Flow l/min (USgpm) Power Versus Speed 93 C (2 F), 1. absolute ( psi gauge) Inlet 56 (75) 28 (4) 52 (7) 25 (36) 48 (64) Power Versus Speed 44 (59) 93 C (2 F), 1. absolute ( psi gauge) Inlet 4 56 (54) (75) 2 (29) 28 (4) 36 52 (48) (7) 25 (36) 32 48 (43) (64) 15 (22) 28 44 (38) (59) 24 4 (32) (54) 2 (29) 1 (15) 2 36 (27) (48) 16 32 (21) (43) 15 12 (16) 5 (7) (22) 28 (38) 248 (32) (11) 25 (365) 4 (5) 17 1 (25) (15) 2 (27) 16 (21) 5 1 15 2 25 3 12 (16) Speed r/min 5 (7) 8 (11) 1.Case Flow at 26 r/min, Full Flow 25 (365) 4 (5) 93 C (2 F), 1. absolute ( psi gauge) 17 Inlet (25) 6 (1.6) 5 (1.3) 5 1 15 2 25 3 4 (1.1) Speed r/min 3 (.8) 1.Case Flow at 26 r/min, Full Flow 2 (.5) 93 C (2 F), 1. absolute ( psi gauge) Inlet 61 (1.6) (.3) 5 (1.3) 4 (1.1) 3 (.8) 2 (.5) 1 (.3) 5 (7) 1 15 2 25 3 35 (15) (22) (29)(36) (44) (5) Case Flow at Cutoff at 26 r/min 93 C (2 F), 1. absolute ( psi gauge) Inlet 42 (11.1) 5 1 15 2 25 3 35 38 (1.) (7) (15) (22) (29)(36) (44) (5) 34 (9.) 3 (7.9) Case Flow at Cutoff at 26 r/min 26 (6.9) 93 C (2 F), 1. absolute ( psi gauge) Inlet 422 (11.1) (5.8) 3818 (1.) (4.8) 14 34 (3.7) (9.) 1 3 (2.6) (7.9) 26 (6.9) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) 22 (5.8) 18 (4.8) 14 (3.7) 1 (2.6) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) 35 (5) 35 (5) Pressure Pressure ( ( 3 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Torque Torque Nm (in-lb) Nm (in-lb) Efficiency Efficiency % % Delivery Delivery l/min l/min (USgpm) (USgpm) Performance Industrial PVM5 Noise Level Noise dba Level dba Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 72 18 r/min Typical max. Noise flow Levels at 18 and 12 r/min with 68Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 72 64 12 r/min max. 18 flow r/min max. flow 68 6 64 56 6 52 56 48 52 44 48 44 12 r/min max. 18 flow r/min min. flow 18 r/min min. flow 5 (7) 5 (7) 1 (15) 1 (15) 15 (22) 15 (22) 12 r/min min. flow 12 r/min min. flow 2 (29) 2 (29) 25 (36) 25 (36) Delivery and Efficiency at 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet Delivery and Efficiency at 18 r/min, 5 C (12 F), 1 and 1. absolute ( psi gauge) Inlet Volumetric Efficiency 1 9 Volumetric Efficiency 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 5 1 15 2 (7) (15) (22) (29) 5 Outlet 1 Pressure 15 ( 2 (7) (15) (22) (29) 125 (33) 125 1 (33) (26) 1 75 (2) (26) 75 5 (2) (13) 5 25 (13) (7) 25 25 (7) (36) 25 (36) Noise Level Noise dba Level dba Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 72 Typical Noise Levels at 15 and max. 1 flow r/min with 68Petroleum Oil (1W) at 5 C (12 F) and 1. 15 absolute r/min max. flow ( psi gauge) Inlet 72 64 1 r/min max. flow 68 6 64 56 6 52 56 48 52 44 48 44 15 r/min max. flow 5 (7) 15 r/min min. flow 15 r/min min. flow equivalent 5 to NFPA. (7) 1 (15) 1 r/min 1 r/min min. flow 1 r/min 1 min. 15 flow (15) (22) Sound pressure data 15 (22) Sound pressure data 2 (29) 2 (29) 25 (36) 25 (36) Torque and Power at 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet Torque and Power at 18 r/min, 5 C (12 F), 24 (2124) and 1. absolute ( psi gauge) Inlet 22 (1947) 24 (2124) 2 (177) 22 (1947) 18 (1593) 2 (177) Torque, 16 (1416) 18 (1593) 14 (1239) Torque, 16 (1416) 12 (162) 14 (1239) 1 (885) 12 (162) 5 (67) 8 (78) Power, 1 (885) 4 (54) 6 (531) 5 (67) 8 (78) 3 (4) Power, 4 (54) 4 (354) Torque, 2 (27) 6 (531) Cut-off 3 (4) 2 (177) 1 (13) 4 (354) Torque, 2 (27) Cut-off 2 (177) 5 1 15 2 251 (13) (7) (15) (22) (29) (36) 5 1 15 2 25 (7) Outlet (15) Pressure (22) (29) ( (36) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 Power Power kw (hp) kw (hp) 31

Efficiency Efficiency % % Torque Torque Nm Nm (in.lb.) (in.lb.) Performance Industrial PVM5 Delivery and Efficiency at 15 r/min, 5 C (12 F), Delivery and and 1. Efficiency absolute at 15 ( psi r/min, gauge) 5 C Inlet (12 F), 1 and 1. absolute ( psi gauge) Inlet Volumetric Efficiency 1 9 Volumetric Efficiency 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 125 (33) 125 (33) 1 (26) 1 75 (2) (26) 75 (2) 5 (13) 5 25 (13) (7) 1 5 1 15 2 (7) (15) (22) (29) 25 25 (7) (36) 5 1 15 2 (7) Outlet (15) Pressure (22) ( (29) 25 (36) Delivery Delivery l/min l/min (USgpm) (USgpm) Delivery and Efficiency at 12 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 8 Efficiency % 7 6 5 4 3 2 1 75 (2) 5 (13) 25 (7) 5 1 15 2 25 (7) (15) (22) (29) (36) 125 (33) 1 (26) De 1 9 8 7 Efficiency % 6 5 4 3 2 1 Torque Torque Nm Nm (in-lb) (in-lb) Torque and Power at 15 r/min, 5 C (12 F), Torque and 1. and Power absolute at 15 ( psi r/min, gauge) 5 C Inlet (12 F), 24 (2124) and 1. absolute ( psi gauge) Inlet 24 22 (2124) (1947) 22 2 (1947) (177) Torque, 2 18 (177) (1593) Torque, 18 16 (1593) (1416) 16 14 (1416) (1239) 14 12 (1239) (162) 12 1 (162) (885) 5 (67) 1 8 (885) (78) Power, 5 4 (67) (54) 8 6 (78) Power, (531) 4 3 (54) (4) 6 4 (531) (354) 3 2 (4) (27) 4 2 (354) (177) 2 1 (27) (13) 2 (177) 1 (13) 5 1 15 2 25 (7) (15) (22) (29) (36) 5 1 15 2 25 (7) Outlet (15) Pressure (22) (29) ( (36) Power Power kw kw (hp) (hp) Torque and Power at 12 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 24 (2124) 22 (1947) 2 (177) 18 (1593) 16 (1416) Torque, 14 (1239) 12 (162) 1 (885) 5 (67) 8 (78) 4 (54) Power, 6 (531) 3 (4) 4 (354) 2 (27) 2 (177) 1 (13) 5 1 15 2 25 (7) (15) (22) (29) (36) Power kw (hp) 32 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Case Case Flow Flow l/min l/min (USgpm) (USgpm) Case Case Flow Flow l/min l/min (USgpm) (USgpm) Performance Industrial PVM5 ) ) Delivery Delivery and and Efficiency Efficiency at at 1 1 r/min, r/min, 5 C 5 C (12 F), (12 F), and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 1 1 Volumetric Efficiency 9 Volumetric Efficiency 9 8 8 7 7 Efficiency % Efficiency % 6 6 5 5 4 4 3 3 Delivery Delivery (effective (effective flow) flow) 2 2 1 1 125 125 (33) (33) 75 75 (2) (2) 5 5 (13) (13) 25 25 (7) (7) 5 5 1 1 15 15 2 2 25 25 (7) (7) (15) (15)(22) (22)(29) (29)(36) (36) Outlet Outlet Pressure Pressure ( ( 1 1 (26) (26) Case Flow versus Outlet Pressure at 18 r/min, Full Flow, Case Flow versus Outlet Pressure at 18 r/min, Full Flow, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 1. (.26) 5 C (12 F), and 1. absolute ( psi gauge) Inlet 1. (.26).9 (.24).9 (.24).8 (.21).8 (.21).7 (.18).7 (.18).6 (.16).6 (.16).5 (.13).5 (.13).4 (.11).4 (.11).3 (.8).3 (.8).2 (.5).2 (.5).1 (.3).1 (.3) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Outlet Pressure ( Power kw (hp) Power kw (hp) Torque Torque and and Power Power at at 1 1 r/min, r/min, 5 C 5 C (12 F), (12 F), and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 24 24 (2124) (2124) 22 22 (1947) (1947) 2 2 (177) (177) 18 18 (1593) (1593) Torque, Torque, 16 16 (1416) (1416) Full Stroke 14 14 (1239) (1239) 12 12 (162) (162) 1 1 (885) (885) 5 5 (67) (67) 8 8 (78) (78) 4 4 (54) (54) 6 6 (531) (531) Power, Power, 3 3 (4) (4) 4 (354) 4 (354) 2 2 (27) (27) 2 2 (177) (177) 1 1 (13) (13) 5 5 1 1 15 15 2 2 25 25 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) Outlet Outlet Pressure Pressure ( ( Power kw (hp) Power kw (hp) Case Flow versus Outlet Pressure at Cutoff, 18 r/min, Case Flow versus Outlet Pressure at Cutoff, 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 5 C (12 F), and 1. absolute ( psi gauge) Inlet 1 (2.64) 1 (2.64) 9 (2.38) (2.38) 8 (2.11) (2.11) 7 (1.85) (1.85) 6 (1.59) (1.59) 5 (1.32) (1.32) 4 (1.6) (1.6) 3 (.79) (.79) 2 (.53) (.53) 1 (.26) (.26) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Outlet Pressure ( EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 33

(%) (%) (%) Noise Level dba Noise Level dba Noise Level dba Performance Mobile PVM5 88 86 84 82 8 78 76 74 72 7 68 88 86 84 82 8 78 76 74 72 7 68 Typical Typical Noise Noise Levels Levels at 26 at 26 & 6 & r/min 6 r/min with with Petroleum Petroleum Oil (1W) Oil (1W) at 93 C at 93 C (2 F) (2 F) and 1. and 1. absolute absolute ( psi ( gauge) psi gauge) inlet inlet 26 26 r/min r/min max. max. flow flow 88 66 66 6 r/min 6 r/min 76 min. flow min. flow 64 64 74 5 5 1 1 15 15 Sound Sound pressure pressure data data(7) (7) (15) (15) 72 (22) (22) equivalent equivalent to NFPA. to NFPA. Outlet Outlet Pressure Pressure 7 ( ( 86 84 82 8 78 68 66 64 Typical Noise Levels at 26 & 6 r/min with Petroleum Oil (1W) at 93 C (2 F) and 1. absolute ( psi gauge) inlet 26 26 r/min r/min min. flow min. flow 26 r/min max. flow 2 2 (29) (29) 6 r/min min. flow 6 r/min 6 r/min max. max. flow flow 26 r/min min. flow 5 1 15 2 (7) (15) (22) (29) Sound pressure data equivalent to NFPA. 25 25 (36) (36) 6 r/min max. flow 25 (36) Overall Efficiency versus versus Speed Speed at 93 C at 93 C (2 F) (2 F) and 1. and 1. absolute absolute ( psi ( gauge) psi gauge) inlet inlet 1 1 14 (37) 14 (37) 95 95 13 (34) 13 (34) 1 1 (15 (15 12 (32) 12 (32) 9 9 11 (29) 11 versus (29) 5 5 (725 (725 Speed Delivery Delivery Delivery and Case Flow 85 85 2 2 at 93 C (2 F) and 1.1 (26) 1 absolute (26) ( psi gauge) inlet Full Flow and 1. a (29 (29 21 21 (3 (3 9 (24) 9 (24) 8 1 Delivery Delivery 8 8 (21) 8 (21) 14 (37) 95 13 (34) 75 75 7 (18) 7 (18) 21 21 (3 (3 1 (15 6 (16) 6 (16) 12 (32) 7 7 9 21 21 (3 (3 11 (29) 5 23 23 (33 (33 5 (13) 5 (13) Case Case Flow Flow 5 (1.32) 5 (1.32) ps 65 65 85 2 4 (11) 4 (11) 1 (26) 4 (1.6) 4 (1.6) (29 9 (24) 6 6 3 (8) 3 (8) 3 (.79) 3 (.79) 8 2 (5) 2 (5) 5 5 (725 (725 8 (21) 2 (.53) 2 (.53) 55 55 75 7 (18) 21 1 (3 (3) 1 (3) Case Case Flow Flow 1 (.26) 1 (.26) 6 (16) 5 5 7 5 5111515222525 3 3 23 (33 5 5 1 1 15 15 2 2 255 25 3 (13) 3 Speed Speed (r/min) (r/min) 65 Speed Speed (r/min) (r/min) 4 (11) 6 3 (8) 2 (5) 55 1 (3) 5 5 1 15 2 25 Speed (r/min) 34 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 Delivery Delivery and Case and Case Flow Flow versus versus Speed Speed at 93 C at 93 C (2 F), (2 F), Full Flow Full Flow and 1. and 1. absolute absolute ( psi ( gauge) psi gauge) inlet inlet 3 Case Flow l/min (USgpm) Case Flow l/min (USgpm) 5 1 S

Torque Torque Nm Nm (in.lb.) (in.lb.) Performance Mobile PVM5 Torque Torque versus versus Speed Speed at 93 C at at (2 F), 93 C (2 F), Full Flow Full Full and Flow 1. and and 1. 1. absolute absolute ( psi ( gauge) ( psi psi gauge) Inlet Inlet 3 (2655) 3 3 (2655) 275 (2434) 275 275 (2434) 25 (2212) 25 25 (2212) 23 23 23 (33 (33 225 (1991) 225 225 (1991) 21 21 21 (3 (3 2 (177) 2 2 (177) Torque Nm (in.lb.) 175 (1549) 175 175 (1549) 15 (1327) 15 15 (1327) 125 (116) 125 125 (116) 1 (885) 1 1 (885) 75 (664) 75 75 (664) 2 2 2 (29 (29 1 1 1 (15 (15 5 (442) 5 5 (442) 17 17 17 (25 (25 25 (221) 25 25 (221) 5 5 5 1 1 15 15 2 2 25 25 3 3 Speed Speed (r/min) (r/min) Power kw (hp) Power Power versus versus Speed Speed at 93 C at at (2 F), 93 C (2 F), Full Flow Full Full and Flow 1. and and 1. 1. absolute absolute ( psi ( gauge) ( psi psi gauge) Inlet Inlet 6 (8) 6 6 (8) (8) 55 (74) 55 55 (74) (74) 5 (67) 5 5 (67) (67) 45 (6) 45 45 (6) (6) Power kw (hp) Power kw (hp) 4 (54) 4 4 (54) (54) 35 (47) 35 35 (47) (47) 3 (4) 3 3 (4) (4) 25 (34) 25 25 (34) (34) 2 (27) 2 2 (27) (27) 15 (2) 15 15 (2) (2) 1 (13) 1 1 (13) (13) 5 (7) 55 (7) (7) 23 23 23 (33 (33 21 21 21 (3 (3 2 2 2 (29 (29 1 1 1 (15 (15 17 17 (25 17 (25 5 5 1 5 15 1 2 15 25 2 3 25 3 Speed Speed (r/min) (r/min) Torque Torque and Case and and Flow Case versus Flow versus Speed Speed at at at 93 C (2 F), 93 C (2 F), Load Sense Load Sense Standby Standby 1. and and 1. 1. absolute absolute ( psi ( gauge) ( psi psi gauge) Inlet Inlet 8 (71) 88 (71) (71) 7 (62) 77 (62) (62) 6 (53) 66 (53) (53) Torque Nm (in.lb.) 5 (44) 55 (44) (44) 4 (35) 44 (35) (35) 2 2 2 (3 (3 diff. diff. diff. Case Flow Case Flow Torque Torque l/min l/min (USgpm) (USgpm) 5. (1.32) 5. 5. (1.32) 11 11 11 (16 (16 diff. diff. diff. Torque Torque 4. (1.6) 4. 4. (1.6) 3 (27) 33 (27) (27) 2 2 2 (3 (3 diff. Case diff. diff. Flow Case Flow 2 (18) 22 (18) (18) 11 11 11 (16 (16 diff.case diff.case Flow Flow 1 (9) 11 (9) (9) 3. (.79) 3. 3. (.79) 2. (.53) 2. 2. (.53) 1. (.26) 1. 1. (.26) 5 5 5 1 1 15 15 2 2 25 25 3 3 Speed Speed (r/min) (r/min) Torque Torque and Case and and Flow Case versus Flow versus Speed Speed at 93 C at at (2 F), 93 C (2 F), Pressure Pressure Limit Cut-off Limit Cut-off and and and 1. 1. 1. absolute absolute ( psi ( gauge) ( psi psi gauge) Inlet Inlet 55 (487) 55 55 (487) 5 (442) 5 5 (442) 21 21 21 (3 (3 Torque Torque 45 (398) 45 45 (398) 4 (354) 4 4 (354) 21 21 21 35 (31) 35 35 (3 (31) (3 3 (265) 3 3 Case (265) Flow Case Flow Case Case Flow l/min Flow l/min 25 (221) 25 25 (221) (USgpm) (USgpm) 2 (177) 2 2 (177) 12 (3.2) 12 12 (3.2) 15 (133) 15 1515 (133) 15 15 (22 (22 Torque Torque 9 (2.4) 99 (2.4) 1 (88) 1 1 (88) (88) 6 (1.6) 66 (1.6) 5 (44) 55 (44) (44) 15 15 15 (22 (22 Case Flow Case Flow 3 (.8) 33 (.8) 5 5 5 1 1 15 15 2 2 25 25 3 3 Speed Speed (r/min) (r/min) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 35

Power kw (hp) Power kw (hp) Performance Industrial PVM57 Noise Level dba Noise Level dba Noise Level dba Noise Level dba Typical Noise Levels at 18 and 12 r/min Typical with Petroleum Noise Levels Oil (1W) at 18 at 5 C and (12 F) 12 r/min Delivery and Efficiency at 18 r/min and with 1. Petroleum absolute Oil (1W) ( psi at gauge) 5 C (12 F) Inlet 5 C (12 F) and 1. absolute ( psi gauge) Inlet 74 and 1. absolute ( psi gauge) Inlet 1 74 Volumetric Efficiency Delivery and Efficiency at 18 r/min 9 5 C (12 F) Overall and 1. Efficiency absolute ( psi gauge) Inlet 18 r/min 1 7 8 Volumetric Efficiency Max. 18 Flow r/min 7 Max. Flow 18 r/min 9 Min. 18 Flow r/min 7 Min. Flow 8 66 6 66 7 5 13 (34) 12 r/min Max. 6 62 12 Flow r/min 4 14 (28) Max. Flow 62 5 13 (34) 3 78 (21) 4 14 (28) 58 2 52 (14) 58 12 r/min 3 78 (21) Min. 12 Flow r/min 1 26 (7) Min. Flow 2 52 (14) 54 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44)(5) 35 54 5 1 15 2 25 3 1 26 (7) (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (44) 3 (7) (15) (22) (29) (36) (44) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) 35 (Sound pressure Outlet data Pressure ( (5) equivalent (Sound pressure to NFPA) data equivalent to NFPA) Torque and Power at 18 r/min Typical Noise Levels at 15 and 1 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet Typical with Petroleum Noise Levels Oil (1W) at 15 at 5 C and (12 F) 1 r/min 3 (2655) and with 1. Petroleum absolute Oil (1W) ( psi at gauge) 5 C (12 F) Inlet Torque and Power at 18 r/min 7 and 1. absolute ( psi gauge) Inlet 27 (239) 5 C (12 F) and 1. Torque, absolute ( psi gauge) Inlet 7 3 (2655) 24 (2124) 15 r/min Max. 27 (239) 15 Flow r/min Torque, 21 (1859) 66 Max. Flow 24 (2124) 66 18 (1593) 6 (8) 1 r/min 21 (1859) Max. 1 Flow r/min 15 (1328) 5 (67) 15 r/min Max. Flow Min. 18 (1593) 12 (162) Power, 6 (8) 62 15 Flow r/min 4 (54) Min. Flow 62 15 (1328) 5 (67) 9 (797) 3 (4) 12 (162) Power, 4 (54) 6 (531) 2 (27) 58 1 r/min 9 (797) 3 (4) 58 Min. 1 Flow r/min 3 (266) Torque, 1 (13) Min. Flow 6 (531) Cut-off 2 (27) 5 1 15 2 25 3 35 3 (266) (7) (15) (22) (29) (36) (44) (5) Torque, 1 (13) 54 Cut-off 54 5 1 15 2 25 3 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (44) 3 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (7) (15) (22) (29) (36) (44)(5) Efficiency % Efficiency % 36 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Power kw (hp) Power kw (hp) Performance Industrial PVM57 Efficiency % Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency at 15 r/min Volumetric Efficiency 5 C (12 F) and 1. absolute ( psi gauge) Inlet 91 Volumetric Efficiency 8 9 7 8 6 7 5 6 1 (26) 4 5 81 (21) (26) 3 4 2 3 1 2 68 (16) (21) 46 (11) (16) 24 (5) (11) 1 2 (5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 Outlet 1 Pressure 15 2 ( 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque and Power at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 33 (2921) Torque and Power at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 3 (2655) 33 (2921) 27 3 (239) (2655) Torque, 24 (2124) 27 (239) 21 (1859) Torque, 24 (2124) 18 21 (1593) (1859) 6 (8) Power, 15 (1328) 18 (1593) 5 6 (67) (8) Power, 12 (162) 15 (1328) 4 5 (54) (67) 9 12 (797) (162) 3 (4) 4 (54) 6 (531) 9 (797) 2 3 (27) (4) 3 (266) 6 (531) 1 (13) 2 (27) 3 (266) 5 1 15 2 25 3 35 1 (13) (7) (15)(22) (29) (36) (44)(5) 5 Outlet 1 Pressure 15 2 ( 25 3 35 (7) (15)(22) (29) (36) (44)(5) Efficiency % Efficiency % Delivery and Efficiency at 12 r/min 5 C (12 F) Delivery and 1. and Efficiency absolute ( at psi 12 gauge) r/min Inlet 1 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Volumetric Efficiency 9 8 8 7 6 5 4 7 6 5 4 1 (26) 1 (26) 8 (21) 8 (21) 3 6 (16) 3 6 (16) 2 4 (11) 2 4 (11) 1 1 2 (5) 2 (5) 5 1 15 2 25 3 35 (7) (15) 1 (22) 15 (29) 2 (36) 25 (44) 3 (5) 35 (7) Outlet (15) Pressure (22) (29) ( (36) (44)(5) Efficiency % Torque and Power at 12 r/min 5 C (12 F) and Torque 1. and absolute Power ( at psi 12 gauge) r/min Inlet 33 (2921) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 33 (2921) 3 (2655) 3 (2655) 27 (239) 27 (239) Torque, 24 (2124) Torque, 24 (2124) 21 (1859) 21 (1859) 18 (1593) 18 (1593) 15 (1328) Power, 15 (1328) Power, 4 (54) 12 (162) 4 (54) 12 (162) 3 (4) 9 (797) 3 (4) 9 (797) 6 (531) 2 (27) 6 (531) 2 (27) 3 (266) 1 (13) 3 (266) 1 (13) 5 1 15 2 25 3 35 (7) (15) 1 (22) 15 (29) 2 (36) 25 (44) 3 (5) 35 (7) Outlet (15) Pressure (22) (29) ( (36) (44) (5) Power kw (hp) Power kw (hp) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 37

Efficiency % Efficiency % Power kw (hp) Power kw (hp) Performance Industrial PVM57 Delivery and Efficiency at 1 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency Volumetric at 1 Efficiency r/min 9 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 8 Volumetric Efficiency 9 7 6 5 8 7 6 4 3 5 4 8 (21) 6 (16) 8 (21) 2 3 4 (11) 6 (16) 1 2 2 (5) 4 (11) 1 5 1 15 2 25 3 35 2 (5) (7) (15) (22) (29) (36) (44) (5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque Outlet and Pressure Power at 1 ( r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 33 (2921) Torque and Power at 1 r/min 3 (2655) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 33 (2921) 27 (239) 3 (2655) Torque, 24 (2124) 27 (239) 21 (1859) Torque, 24 (2124) 18 (1593) 21 (1859) 15 (1328) 18 (1593) 12 (162) Power, 4 (54) 15 (1328) 9 (797) 3 (4) 12 (162) Power, 4 (54) 6 (531) 2 (27) 9 (797) 3 (4) 3 (266) 1 (13) 6 (531) 2 (27) 3 (266) 5 1 15 2 25 3 35 1 (13) (7) (15) (22) (29) (36) (44) (5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Case Case Flow Flow Versus Versus Outlet Outlet Pressure at at Full Full Flow, Flow, 18 18 r/min r/min 5 C 5 C (12 F) (12 F) and and 1. 1. absolute ( ( psi psi gauge) gauge) Inlet Inlet 5 (1.32) 5 (1.32) 4 (1.6) 4 (1.6) 3 (.79) 3 (.79) 2 (.53) 2 (.53) 1 (.26) 1 (.26) 5 5 1 1 15 15 2 2 25 25 3 3 35 35 (7) (7)(15) (15) (22) (22) (29) (29) (36) (36) (44) (44) (5) (5) Outlet Outlet Pressure ( ( Case Case Flow Flow Versus Versus Outlet Outlet Pressure at at Cutoff, Cutoff, 18 18 r/min r/min 5 C 5 C (12 F) (12 F) and and 1. 1. absolute ( ( psi psi gauge) gauge) Inlet Inlet 1,1 1,1 (.29) (.29) 1, 1, (.26) (.26),9,9 (.24) (.24),8,8 (.21) (.21),7,7 (.18) (.18),6,6 (.16) (.16),5,5 (.13) (.13) 5 5 1 1 15 15 2 2 25 25 3 3 35 35 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) (44) (44) (5) (5) Outlet Outlet Pressure ( ( 38 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Efficiency % Case Flow l/min (USgpm) Case Flow l/min (USgpm) Performance Mobile PVM57 Noise Level dba Typical Noise Levels Delivery and Case Flow Versus Speed Petroleum Oil (1W) at 93 C (2 F), @ 93 C (2 F), full flow and 1. absolute ( gauge Inlet 1. absolute ( psi gauge) Inlet 15 (4) 82 14 (37) Delivery and Case 5 Flow (7 Versus, Speed 13 (34) @ 93 C (2 F), full flow and 78 25 r/min Delivery 1. absolute ( gauge Inlet 1215 (32)(4) Max. Flow 25 r/min Min. Flow 1114 (29)(37) 74 5 (7, 113 (26)(34) Delivery 912 (24)(32) 7 28 (4, 811 (21)(29) Delivery 66 71 (18)(26) 6 (16) 9 (24) 28 (4, Case flow 28 (4 6,, (1.6) 62 5 (13) 8 (21) Delivery 5, (1.3) 6 r/min 4 (11) 7 (18) 4, (1.1) Max. Flow 58 36 (8)(16) 28 (4, 3, (.8) 6, (1.6) 6 r/min Case flow 25 (5)(13) 5 (7, 2, (.5) 5, (1.3) Min. Flow 54 14 (3)(11) Case flow 1, (.3) 4, (1.1) 3 (8) 3, (.8) 5 2 (5) 5 1 15 5 2 (7 25, 2, (.5) 5 1 15 2 25 3 Speed r/min Case flow (7) (15) (22) (29) (36) (44) 1 (3) 1, (.3) Torque Versus Speed (Sound pressure 5 1 15 2 25 @ 93 C (2 F), full flow and data equivalent to NFPA) Speed r/min 1. absolute ( psi gauge) inlet 32 (2832) Torque Versus Speed 32 Versus Speed 3 (2655) @ 93 C (2 F), full flow and (46 at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 28 (2478) 1. absolute ( psi gauge) inlet 95 2632 (1858) (2832) 5 32 (7 243 (2124) (2655) 25 (46 22 (1947) 9 28 (2478) (36 1 226 (177) (1858) (15 2 1824 (1593) (2124) 15 (29 25 85 1622 (1416) (1947) (22 (36 14 (1239) 15 2 (177) (22 2 1218 (162) 2 (1593) 8 (29 116 (885) (1416) 1 (29 (15 814 (78) (1239) 15 612 (531) (162) 5 (22 75 (7 25 41 (354) (885) 1 (36 17 (15 2 (177) 8 (78) (25 7 6(531) 5 5 1 15 2 25 3 28 (7 4 (354) Speed r/min (4 17 2 (177) 65 (25 5 1 15 2 25 5 1 15 2 25 3 Speed r/min Speed r/min 28 (4 28 (4 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 39

Case Flow l/min (USgpm) Performance Mobile PVM57 Power Versus Speed 93 C (2 F), 1. absolute ( psi gauge) Inlet 78 (15) 32 (46) 72 (97) 66 (89) 28 (4) 6 (8) 25 (36) 54 (72) 48 (64) 2 (29) 42 (56) 36 (48) 15 (22) 3 (4) 24 (32) 1 (15) 18 (24) 12 (16) 5 (7) 6 (8) 17 (25) 5 1 15 Speed r/min 2 25 Torque and Case Flow Versus Speed @ 93 C (2 F), load sense standby and 1. absolute ( psi gauge) inlet 6 (53) 2 (3 5 (44) differential, 11 (16 Torque 4 (35) differential, 8. (2.11) 3 (27) Torque 6. (1.58) 2 (18) 4. (1.6) 11 (16 differential, 1 (9) Case Flow 2. (.53) 2 (3 differential, Case Flow 5 1 15 2 25 Speed r/min Torque and Case Flow Versus Speed @ 93 C (2 F), cut-off and 1. absolute ( psi gauge) inlet 1 (885) 9 (796) 28 (4 Torque 8 (78) 7 (619) 28 6 (531) (4 5 (442) Case Flow 1 (2.6) 4 (354) 8 (2.1) 3 (265) 15 (22, Case Flow 6 (1.6) 2 (177) 4 (1.1) 15 (22, Torque 1 (88) 5 1 15 2 25 2 (.5) Speed r/min Power @ Full Flow kw (hp) Case Flow l/min (USgpm) Pressure ( 4 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Noise Level Noise dba Level dba Efficiency % Efficiency % Performance Industrial PVM63 Typical Noise Levels at 18 and 12 r/min. with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 75 Typical 18 Noise r/minlevels at 18 and 12 r/min. with max. flow Petroleum Oil (1W) at 5 C (12 F) and 1. 7 absolute ( psi gauge) Inlet 75 12 r/min 18 r/min max. flow min. 18 flowr/min 65 max. flow 7 6 65 55 6 18 r/min min. flow 12 r/min max. flow 12 r/min min. flow 5 12 r/min 5 1 15 min. 2 flow 25 55 (7) (15) (22) (29) (36) 5 5 1 15 2 (7) (15) (22) (29) 25 (36) Delivery and Efficiency at 18 r/min, 5ϒC (12ϒF), Delivery and and 1. Efficiency absolute at ( 18 psi r/min, gauge) 5ϒC Inlet (12ϒF), and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency Volumetric Efficiency 9 9 8 8 7 7 6 12 (32) 6 12 (32) 5 1 (26) 5 1 (26) 4 8 (21) 4 8 (21) 3 6 (16) 3 6 (16) 2 4 (11) 2 4 (11) 1 2 (5) 1 2 (5) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) D Noise Level Noise dba Level dba 75Typical Noise Levels at 15 and 1 r/min. with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute 15 r/min ( psi gauge) Inlet 7 75 65 7 6 65 55 Typical Noise Levels at 15 and 1 r/min. with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 15 r/min min. flow 15 r/min min. flow max. flow 15 r/min max. flow 6 5 1 r/min 5 1min. flow 15 2 55 (7) (15) (22) (29) Sound pressure data 5 equivalent 5 to NFPA. 1 15 2 (7) (15) (22) (29) Sound pressure data 1 r/min min. flow 1 r/min max. flow 1 r/min max. flow 25 (36) 25 (36) Torque and Power at 18 r/min, 5ϒC (12ϒF), and Torque 1. and absolute Power at ( 18 psi r/min, gauge) 5ϒC Inlet(12ϒF), and 1. absolute ( psi gauge) Inlet 27 (239) 27 (239) 24 (2124) 24 (2124) 21 (1859) 21 (1859) Torque, Full Stroke Torque, 18 (1593) 18 (1593) 15 (1328) 5 (67) 15 (1328) 5 (67) 12 (162) 4 (54) 12 (162) 4 (54) 9 (1327) Power, 3 (4) 9 (1327) Full Stroke Power, 3 (4) 6 (531) 2 (27) 6 (531) 2 (27) Torque, 3 (226) Cut-off Torque, 1 (13) 3 (226) Cut-off 1 (13) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 Power kw (hp) Power kw (hp) 41

Torque Torque Nm Nm (in.lb.) (in.lb.) Performance Industrial PVM63 Delivery and Efficiency at 15 r/min, 5ϒC (12ϒF), Delivery and and 1. Efficiency absolute at 15 ( psi r/min, gauge) 5ϒC Inlet (12ϒF), and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency Volumetric Efficiency 9 9 8 8 7 7 Efficiency % 6 6 5 5 4 4 3 3 1 (26) 1 (26) 8 (21) 8 (21) 6 (16) 6 (16) 2 2 4 (11) 4 (11) 1 1 2 (5) 2 (5) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Outlet Pressure ( Delivery l/min (USgpm) Delivery Delivery and and Efficiency Efficiency at at 12 12 r/min, r/min, 5ϒC 5ϒC (12ϒF), (12ϒF), and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 1 1 Volumetric Volumetric Efficiency Efficiency 9 9 Overall Overall Efficiency Efficiency 8 8 Efficiency % 7 7 6 6 5 5 4 4 3 3 2 2 Delivery Delivery (effective (effective flow) flow) 5 5 1 1 15 15 2 2 (7) (7) (15) (15) (22) (22) (29) (29) Outlet Outlet Pressure Pressure ( ( 25 25 (36) (36) 1 1 (26) (26) 8 8 (21) (21) 6 6 (16) (16) 4 4 (11) (11) 1 1 2 2 (5) (5) Delivery -l/min -l/min (USgpm) Delive Delive 1 1 9 9 8 8 Efficiency % 7 7 6 6 5 5 4 4 3 3 2 2 1 1 Torque Nm Nm (in.lb.) Torque and Power at 15 r/min, 5ϒC (12ϒF), Torque and 1. and Power absolute at 15 ( psi r/min, gauge) 5ϒC Inlet (12ϒF), and 1. absolute ( psi gauge) Inlet 27 (239) 27 (239) 24 (2124) 24 (2124) 21 (1859) 21 (1859) 18 (1593) 18 (1593) 15 (1328) 15 (1328) 12 (162) 12 (162) Torque, Torque, 5 (67) 5 (67) 4 (54) 4 (54) 9 (1327) 3 (4) 9 (1327) 3 (4) 6 (531) Power, 2 (27) 6 (531) Power, 2 (27) 3 (226) 1 (13) 3 (226) 1 (13) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Outlet Pressure ( Power kw kw (hp) (hp) Torque Torque Nm Nm (in.lb.) (in.lb.) Torque Torque and and Power Power at at 12 12 r/min, r/min, 5ϒC 5ϒC (12ϒF), (12ϒF), and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 27 27 (239) (239) 24 24 (2124) (2124) 21 21 (1859) (1859) 18 18 (1593) (1593) 15 15 (1328) (1328) 12 12 (162) (162) 9 9 (1327) (1327) 6 6 (531) (531) 3 3 (226) (226) Torque, Torque, Full Full Stroke Stroke Power, Power, Full Full Stroke Stroke 5 5 1 1 15 15 2 2 25 25 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) Outlet Outlet Pressure Pressure ( ( 5 5 (67) (67) 4 4 (54) (54) 3 3 (4) (4) 2 2 (27) (27) 1 1 (13) (13) Power Power kw kw (hp) (hp) In In 27 27 24 24 21 21 18 18 15 15 12 12 9 42 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Performance Industrial PVM63 6) Delivery -l/min (USgpm) Delivery -l/min (USgpm) ) ) ) Delivery and Efficiency at 1 r/min, 5ϒC (12ϒF), Delivery and Efficiency at 1 r/min, 5ϒC (12ϒF), and 1. absolute ( psi gauge) Inlet and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency Volumetric Efficiency 9 9 8 8 Efficiency % Efficiency % 7 7 6 6 5 5 4 4 3 3 2 2 1 1 8 (21) 8 (21) 6 (16) 6 (16) 4 (11) 4 (11) 2 (5) 2 (5) 5 1 15 2 25 5 1 15 2 25 (7) (15) (22) (29) (36) (7) (15) (22) (29) (36) 1 (26) 1 (26) Case Flow l/min - (USgpm) Case Flow versus Outlet Pressure at 18 r/min, Full Flow, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 5 (1.32) 4 (1.6) 3 (.79) 2 (.53) 1 (.26) 5 (7) 1 (15) 15 (22) 2 (29) Outlet Pressure - ( 25 (36) ), 7) Power kw (hp) Power kw (hp) 4) ) 7) 3) Torque and Power at 1 r/min, 5ϒC (12ϒF), Torque and Power at 1 r/min, 5ϒC (12ϒF), and 1. absolute ( psi gauge) Inlet and 1. absolute ( psi gauge) Inlet 27 (239) 27 (239) 24 (2124) 24 (2124) 21 (1859) 21 (1859) 18 (1593) 18 (1593) 15 (1328) 15 (1328) 12 (162) 12 (162) 9 (1327) 9 (1327) Torque, Full Stroke Torque, 5 (67) 5 (67) 4 (54) 4 (54) 3 (4) 3 (4) 6 (531) 6 (531) 2 (27) 2 (27) 3 (226) 3 (226) Power, Full Stroke Power, 1 (13) 1 (13) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Power kw (hp) Power kw (hp) Case Flow l/min - (USgpm) Case Flow versus Outlet Pressure at Cutoff, 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 12 (3.17) 11 (2.91) 1 (2.64) 9 (2.38) 8 (2.11) 7 (1.85) 6 (1.59) 5 (1.32) 4 (1.6) 3 (.79) 2 (.53) 1 (.26) 5 1 15 2 (7) (15) (22) (29) Outlet Pressure - ( 25 (36) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 43

Case Flow l/min (USgpm) Case Flow l/min (USgpm) Performance Typical Typical Noise Levels Noise at Levels 25 at & 25 6 r/min & 6 with r/min Petroleum with Petroleum Oil (1W) Oil (1W) Mobile at 93 C at (2 F) 93 C (2 F) and 1. and 1. absolute absolute ( psi gauge) ( psi gauge) Inlet Inlet PVM63 85 85 25 r/min 25 r/min min. flowmin. flow 8 8 25 r/min 25 r/min max. flow max. flow 75 75 Typical Noise Levels at 25 & 6 r/min with Petroleum Oil (1W) at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 85 Noise Level dba 7 65 6 55 Noise Level dba 7 65 6 55 8 6 r/min 6 r/min max. flow max. flow 75 6 r/min 6 r/min min. flowmin. flow 7 5 5 5 51 1 15 15 2 2 2565 25 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) Outlet Pressure ( Sound pressure Sound pressure data data 6 equivalent equivalent to NFPA. to NFPA. Noise Level dba 55 25 r/min min. flow 25 r/min max. flow 6 r/min max. flow 6 r/min min. flow 5 5 1 15 2 (7) (15) (22) (29) Sound pressure data equivalent to NFPA. 25 (36) Overall Efficiency versus versus Speed Speed 93 C at (2 F) 93 C (2 F) and 1. and 1. absolute absolute ( psi gauge) ( psi gauge) inlet inlet Delivery Delivery and Case and Flow Case versus Flow versus Speed at Speed 93 C at (2 F), 93 C (2 F), Full Flow Full 1. Flow 1. absolute absolute ( psi gauge) ( psi gauge) Inlet Inlet 16 (42) 16 (42) 1 5 95 14 (37) 14 (37) 5 (725 5 (725 5 (725 5 (725 9 12 (32) 12 (32) Delivery Delivery 1 1 versus Speed Delivery and Case Flow 5 (145 85 (145 at 93 C (2 F) and 1 1. (26) 1 absolute (26) ( psi gauge) inlet Full Flow 1. ab 8 21 21 (3 (3 16 (42) 1 8 (21) 8 (21) Delivery Delivery 5 75 15 15 95 14 (37) 7 (22 5 (725 6 (16) 8 (2.11) (22 6 (16) 8 (2.11) 5 5 65 9 6 4 (11) 12 (1.59) (32) 6 (1.59) Deliver 23 (33 4 (11) 23 (33 1 21 21 (3 (3 Case Flow Case Flow 6 21 4 (1.6) 21 85 4 (1.6) (145 (3 2 (5) 1 (26) (3 2 (5) 2 (.53) 55 8 5 (725 Case Flow 5 5 (725 Case Flow 2 (.53) 8 (21) 5 75 5 5 1 1 15 15 2 2 25 25 3 153 5 1 5 15 1 2 15 25 2 3 25 7 (22 6 (16) 3 Speed Speed r/min r/min Speed (r/min) Speed (r/min) 65 4 (11) 23 (33 21 b 6 21 (3 2 (5) 55 5 ba (%) (%) 5 5 1 15 2 25 Speed r/min 44 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 3 5 1 Sp

Case Flow l/min (USgpm) Case Flow l/min (USgpm) Case Case Flow Flow l/min l/min (USgpm) (USgpm) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Case Case Flow Flow l/min l/min (USgpm) (USgpm) Performance Mobile PVM63 Torque versus Speed at at 93 C 93 C (2 F), Power versus Speed at at 93 C 93 C (2 F), Full Full Flow Flow and and 1. 1. absolute ( ( psi psi gauge) Inlet Inlet Full Full Flow Flow and and 1. 1. absolute ( ( psi psi gauge) Inlet Inlet 3 3 (2655) Torque versus Speed at 93 C (2 F), 1 1 (134) (134) Power versus Speed at 93 C (2 F), Full Flow and 1. absolute ( psi gauge) Inlet Full Flow and 1. absolute ( psi gauge) Inlet 9 9 (121) (121) 25 25 3 (2212) (2655) 1 (134) 23 23 (33 8 8 (17) (17) 9 (121) 21 21 (3 23 23 (33 7 (94) 2 2 7 (94) 25 (177) (2212) 21 21 (3 23 (33 8 (17) 21 (3 6 6 (8) (8) 23 (33 15 15 (22 7 (94) 15 15 2 (1327) (177) 21 (3 5 5 (67) (67) 6 (8) 15 15 (22 15 (22 4 4 (54) (54) 1 1 1 15 (885) (885) (1327) 1 (15 5 (67) 3 3 (4) (4) 1 1 15 (15 (22 4 (54) 5 5 1 (725 (725 (15 2 (27) 5 5 1 (442) (442) (885) 2 (27) 3 (4) 5 5 1 (725 (725 (15 17 17 (25 (25 1 1 (13) (13) 5 (725 2 (27) 17 17 (25 (25 5 (442) 5 (725 5 51 115 152 225 253 17 3 (25 1 (13) 5 51 115 152 225 253 3 17 (25 Speed (r/min) Speed (r/min) 5 1 15 2 25 3 5 1 15 2 25 3 Speed (r/min) Speed (r/min) Torque and and Case Case Flow Flow versus Speed Torque and and Case Case Flow Flow versus Speed at at 93 C 93 C (2 F), Load Load Sense Standby and and at at 93 C 93 C (2 F), Pressure Limit Limit Cut-off and and 1. 1. 1. 1. absolute ( ( psi psi gauge) Inlet Inlet absolute ( ( psi psi gauge) Inlet Inlet Torque and Case Flow versus Speed Torque and Case Flow versus Speed 8 (71) 8 (71) at 93 C (2 F), Load Sense Standby 2. 2. and (5.28) (5.28) 8 8 (78) (78) at 93 C (2 F), Pressure Limit Cut-off and 2. 2. 1. (5.28) (5.28) 1. absolute ( psi gauge) Inlet 18. 18. (4.76) (4.76) 21 absolute 21 (3 (3 ( gauge) Torque Inlet 7 (62) 7 (619) 18. (4.76) 7 (62) 7 (619) 18. (4.76) 8 (71) 2. (5.28) 8 (78) 2. (5.28) 2 2 (3 (3 16. 16. (4.23) (4.23) 16. 16. (4.23) (4.23) 6 (53) 6 (531) Case Flow 6 (53) 6 (531) Case Flow 18. (4.76) 21 (3 Torque diff. diff. Torque 7 (62) 7 (619) 18. (4.76) 14. 14. (3.7) (3.7) 14. 14. (3.7) (3.7) 5 (44) 5 (44) 2 (3 16. (4.23) 5 5 (442) (442) 16. (4.23) 12. 12. (3.17) (3.17) 6 (53) 6 (531) 21 (3 Case Flow diff. Torque 12. 12. (3.17) (3.17) 14. (3.7) 15 15 (22 (22 14. (3.7) 4 (35) 4 (35) 11 (16 diff. 1. (2.64) 4 (354) 11 (16 diff. 1. (2.64) 4 (354) Case Case Flow Flow 1. 1. (2.64) (2.64) 5 (44) 5 (442) Torque 12. (3.17) 12. (3.17) 8. 8. (2.11) (2.11) 3 (27) 3 (265) 8. (2.11) 3 (27) 3 (265) 15 (22 8. (2.11) 4 (35) 2 2 (3 (3 11 (16 diff. 1. (2.64) 4 (354) Case Flow 1. (2.64) 6. 6. (1.59) (1.59) diff. diff. Case Case Flow Flow Torque 6. 6. (1.59) (1.59) 2 (18) 2 (18) 8. (2.11) 2 2 (177) (177) 3 (27) 3 (265) 8. (2.11) 4. 4. (1.6) (1.6) 15 15 (22 Torque 2 (3 4. 4. (1.6) (1.6) 11 11 (16 (16 diff. diff. 1 (9) 1 (9) 6. (1.59) Case Case Flow Flow 1 1 (88) (88) diff. Case Flow 6. (1.59) 2 (18) 2. 2. (.53) (.53) 2 (177) 2. 2. (.53) (.53) 4. (1.6) 15 (22 Torque 4. (1.6) 11 (16 diff. 1 (9) 5 51 115 15 Case 2 2 Flow 1 25 253 3 (88) 2. (.53) 5 5 1 115 152 225 253 3 2. (.53) Speed (r/min) Speed (r/min) 5 1 15 2 25 3 5 1 15 2 25 3 Speed (r/min) Speed (r/min) Power kw (hp) Power kw (hp) Power kw (hp) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 45

Performance Industrial PVM74 Noise Level Noise dba Level dba Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 76 Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) 74 18 r/min and 1. absolute ( psi gauge) Max. Inlet Flow 76 72 74 18 r/min Max. 18 Flow r/min 7 Min. Flow 72 68 18 r/min 7 Min. Flow 66 68 12 r/min 64 Max. Flow 66 62 12 r/min 64 Max. Flow 6 12 r/min 62 Min. Flow 58 5 1 15 2 25 6 (7) (15) 12 r/min (22) (29) (36) Min. Flow 58 Sound pressure 5 1 data 15 2 25 equivalent (7) to (15) NFPA. (22) (29) (36) Sound pressure data equivalent to NFPA. 3 (44) 3 (44) Efficiency % Delivery and Efficiency at 18 r/min 5 C (12 F) Delivery and 1. and Efficiency absolute ( at psi 18 gauge) r/mininlet 1 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Volumetric Efficiency 9 8 8 7 7 6 15 (4) 6 15 (4) 5 125 (33) 5 125 (33) 4 3 2 1 4 3 2 1 1 (26) 1 (26) 75 (2) 75 (2) 5 (13) 5 (13) 25 (7) 25 (7) 5 1 15 2 25 3 35 (7) (15) 1 (22) 15 (29) 2 (36) 25 (44) 3 (5) 35 (7) Outlet (15) Pressure (22) (29) ( (36) (44)(5) Efficiency % Noise Level Noise dba Level dba 72 7 72 68 7 66 68 64 66 62 64 6 62 58 6 56 58 56 Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) 1 Inlet r/min Min. Flow 15 r/min Max. Flow 15 r/min Max. Flow 5 (7) 5 (7) 1 r/min Min. Flow 15 r/min Min. Flow 15 r/min Min. 1 Flow r/min Max. Flow 1 r/min Max. Flow 1 15 2 25 (15) (22) (29) (36) 1 (15) 15 (22) 2 (29) 25 (36) 3 (44) 3 (44) Torque and Power at 18 r/min 5 C (12 F) and Torque 1. and absolute Power ( at psi 18 gauge) r/mininlet 4 (354) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 4 (354) 36 (3186) Torque, 36 (3186) Full Stroke Torque, 32 (2832) 32 (2832) 28 (2478) 28 (2478) 24 (2124) 24 (2124) 2 (177) 2 (177) Power, 16 (1416) Full Stroke Power, 8 (17) 16 (1416) 8 (17) 12 (162) 6 (8) 12 (162) 6 (8) 8 (78) Torque, 4 (54) 8 (78) Cut-off Torque, 4 (54) Cut-off 4 (354) 2 (27) 4 (354) 2 (27) 5 1 15 2 25 3 35 (7) (15) 1 (22) 15 (29) 2 (36) 25 (44) 3 (5) 35 (7) Outlet (15) Pressure (22) (29) ( (36) (44) (5) Power kw (hp) Power kw (hp) 46 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Performance Industrial PVM74 Efficiency % Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency at 15 r/min Volumetric 5 C (12 F) Efficiency and 1. absolute ( psi gauge) Inlet 9 1 Volumetric Efficiency 8 9 7 8 6 7 5 6 125 (33) 4 5 1 125 (26) (33) 3 2 1 4 3 2 75 1 (2) (26) 5 75 (13) (2) 25 5 (7)(13) 1 5 1 15 2 25 3 (7) (15) (22) (29)(36) (44)(5) 35 25 (7) 5 Outlet 1 Pressure 15 2 ( 25 3 (7) (15) (22) (29) (36) (44)(5) 35 Efficiency % Efficiency % Power kw (hp) Power kw (hp) Delivery and Efficiency at 12 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet Delivery and Efficiency at 12 r/min 1 5 C (12 F) and 1. absolute Volumetric ( psi gauge) Efficiency Inlet 9 8 7 6 5 1 9 8 7 6 Volumetric Efficiency 125 (33) 4 5 1 (26) 125 (33) 3 2 1 4 3 2 75 (2) 1 (26) 5 (13) 75 (2) 25 (7) 5 (13) 1 25 (7) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Outlet 5 Pressure 1 15 2 ( 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque and Power at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet Torque and Power at 12 r/min 4 (354) Torque and Power at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 5 C (12 F) and 1. absolute ( psi gauge) Inlet Torque and Power at 12 r/min 4 (354) 36 (3186) 4 (354) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 36 (3186) 4 (354) Torque, 32 (2832) Torque, 36 (3186) 32 (2832) 36 (3186) Torque, 28 (2478) 32 (2832) Torque, 28 (2478) 32 (2832) 24 (2124) 28 (2478) 24 (2124) 28 (2478) 2 (177) 24 (2124) 2 (177) 24 (2124) 16 (1416) 2 (177) Power, 8 (17) 16 (1416) 2 (177) 8 (17) 12 (162) 16 (1416) Power, 6 (8) (17) 12 (162) 16 (1416) Power, 6 (8) 8 (17) 812 (78) (162) 4 6 (54) (8) Power, 8 (78) 12 (162) 4 (54) 6 (8) 4 (354) 8 (78) 2 4 (27) (54) 4 (354) 8 (78) 2 (27) 4 (54) 4 (354) 2 (27) 5 1 15 2 25 3 35 4 (354) 2 (27) (7) (15) (22) (29) (36) (44) (5) 5 1 15 2 25 3 35 5 1 15 2 25 3 35 (7) (15) (22) (29)(36) (44)(5) (7) (15) (22) (29) (36) (44) (5) Outlet 5 Pressure 1 15 ( 2 25 3 35 (7) (15) (22) (29)(36) (44)(5) Efficiency % Power kw (hp) Power kw (hp) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 47

Performance Industrial PVM74 Torque and Power at 1 r/min 5 C (12 F) and Torque 1. and absolute Power ( at psi 1 gauge) r/min Inlet 4 (354) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 4 (354) 36 (3186) 36 (3186) Torque, 32 (2832) Torque, 32 (2832) 28 (2478) 28 (2478) 24 (2124) 24 (2124) 2 (177) 2 (177) 16 (1416) 8 (17) 16 (1416) 8 (17) 12 (162) 6 (8) Power, 12 (162) 6 (8) 8 (78) Power, 4 (54) 8 (78) 4 (54) 4 (354) 2 (27) 4 (354) 2 (27) 5 1 15 2 25 3 (7) (15)(22) (29) (36) (44)(5) 35 5 1 15 2 25 3 (7) (15)(22) (29) (36) (44)(5) 35 Efficiency % Delivery and Efficiency at 1 r/min 5 C (12 F) Delivery and 1. and absolute Efficiency ( at psi 1 gauge) r/min Inlet 1 5 C (12 F) and 1. absolute Volumetric ( psi Efficiency gauge) Inlet 1 9 Volumetric Efficiency 9 8 7 6 5 4 8 7 6 5 1 (26) 4 1 (26) 3 75 (2) 3 75 (2) 2 5 (13) 1 2 5 (13) 25 (7) 1 25 (7) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 1 15 2 25 3 35 (7) Outlet (15) Pressure (22) (29) ( (36) (44) (5) Efficiency % Power kw (hp) Case Flow - l/min (USgpm) Case Flow - l/min (USgpm) Power kw (hp) Case Flow - l/min (USgpm) Case Flow - l/min (USgpm) Case Flow Versus Outlet Pressure at Full Flow, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 5, (1.32) Case Flow Versus Outlet Pressure at Full Flow, 18 r/min 4,5 (1.19) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 5, (1.32) 4, (1.6) 3,5 4,5 (.92) (1.19) 3, 4, (.79) (1.6) 2,5 3,5 (.66) (.92) 2, 3, (.53) (.79) 1,5 2,5 (.4) (.66) 1, 2, (.26) (.53),5 1,5 (.13) (.4) 1, (.26) 5 1 15 2 25 3 35,5 (.13) (7) (15)(22) (29)(36) (44)(5) 5 1 15 2 25 3 35 Case Flow (7) Versus (15) Outlet (22) Pressure (29) at (36) Cutoff, (44) 18 r/min (5) 5 C (12 F) and Outlet 1. Pressure absolute ( ( gauge) Inlet 12 (3.17) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1112 (2.91) (3.17) 11 (2.91) 1 (2.64) 9 1 (2.38) (2.64) 8 9 (2.11) (2.38) 8 (2.11) 7 (1.85) 5 1 15 2 25 3 35 (7) (15) (22)(29) (36)(44) (5) 7 (1.85) Outlet Pressure - ( 5 1 15 2 25 3 35 (7) (15) (22)(29) (36)(44) (5) Outlet Pressure - ( 48 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Performance Mobile PVM74 Noise Level dba Efficiency % 84 84 8 8 76 76 72 72 68 68 64 64 6 6 56 56 Typical Typical Noise Noise Levels Levels Petroleum Petroleum Oil Oil (1W) (1W) at at 93 C 93 C (2 F), (2 F), 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet (Sound (Sound pressure pressure data data equivalent equivalent to to NFPA) NFPA) 24 24 r/min r/min Min. Min. Flow Flow 24 24 r/min r/min Max. Max. Flow Flow 6 6 r/min r/min Min. Min. Flow Flow 6 6 r/min r/min Max. Max. Flow Flow 52 52 5 5 1 1 15 15 2 2 25 25 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) Outlet Outlet Pressure Pressure ( ( 3 3 (44) (44) Overall Overall Efficiency Efficiency Versus Versus Speed Speed at at 93 C 93 C (2 F) (2 F) and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 95 95 9 9 5 5 (7 (7 85 85 1 1 (15 (15 8 15 8 15 (22 (22 2 75 2 75 (29 (29 25 25 7 7 (36 (36 28 28 (4 65 (4 65 32 32 (46 (46 6 6 5 5 1 1 15 15 2 2 25 25 Speed Speed r/min r/min Power @ Full Flow kw (hp) Delivery and Case Flow Versus Speed @ 93 C (2 F), full flow and 1. absolute ( gauge Inlet 18 (48) 16 (42) 5 (7, Delivery 14 (37) 12 (32) 28 (4, 1 (26) Delivery 8 (21) 8 (2.1) 6 (16) 28 (4, Case flow 6 (1.6) 4 (11) 4 (1.1) 2 (5) 5 (7, Case flow 2 (.5) 5 1 15 2 25 Speed r/min Torque Versus Speed @ 93 C (2 F), full flow and 1. absolute ( psi gauge) inlet 4 (354) 32 (46 35 (397) 28 (4 3 (2655) 25 (2212) 2 (177) 15 (1327) 1 (885) 5 (442) 1 (15 5 (7 17 (25 5 1 15 2 25 Speed r/min Case Flow l/min (USgpm) 25 (36 2 (29 15 (22 Power Versus Speed 93 C (2 F), 1. absolute ( psi gauge) Inlet 1 (134) 32 (46) 9 (121) 8 (17) 28 (4) 7 (94) 25 (36) 6 (8) 2 (29) 5 (67) 15 (22) 4 (54) 3 (4) 1 (15) 2 (27) 5 (7) 1 (13) 17 (25) 5 1 15 2 25 Speed r/min Pressure ( Pressure ( EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 49

Torque Torque Nm Nm (in.lb.) (in.lb.) Case Case Flow Flow l/min l/min (USgpm) (USgpm) Case Case Flow Flow l/min l/min (USgpm) (USgpm) Performance Mobile PVM74 7 (62) (62) Torque Torque and and Case Case Flow Flow Versus Versus Speed Speed @ 93 C 93 C (2 F), (2 F), load load sense sense standby standby and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) inlet inlet 2 2 (3 (3 differential, differential, Torque Torque 6 (53) (53) 5 (44) (44) 4 (35) (35) 3 (27) (27) 2 (18) (18) 11 11 (16) (16) differential differential Torque Torque 2 2 (3 (3 differential differential Case Case Flow Flow 8. 8. (2.11) (2.11) 6. 6. (1.58) (1.58) 4. 4. (1.6) (1.6) 1 (9) (9) 2. 2. (.53) (.53) 11 11 (16 (16 differential differential Case Case Flow Flow 5 5 1 1 15 15 2 2 25 25 Speed Speed r/min r/min 16 16 (1416) (1416) 14 14 (1239) (1239) Torque Torque and and Case Case Flow Flow Versus Versus Speed Speed @ 93 C 93 C (2 F), (2 F), cut-off cut-off and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) inlet inlet 28 28 (4 (4,, Torque Torque 12 12 (162) (162) 1 1 (885) (885) 8 8 (78) (78) 15 15 (22 (22,, Torque Torque 6 6 (531) (531) 3 3 (7.9) (7.9) 28 28 (4 (4,, Case Case Flow Flow 4 4 (354) (354) 2 2 (5.3) (5.3) 2 2 (177) (177) 1 1 (2.6) (2.6) 15 15 (22 (22,, Case Case Flow Flow 5 5 1 1 15 15 2 2 25 25 Speed Speed r/min r/min 5 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Performance Industrial PVM81 Noise Noise Level Level dba dba Typical Noise Levels at 18 and 12 r/min. with Petroleum Oil (1W) at 5 C (12 F) Typical and Noise 1. Levels absolute at 18 ( and psi 12 gauge) r/min. Inletwith 74 Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 18 r/min 74 min. flow 72 18 r/min 18 r/min min. flow 72 7 max. flow 18 r/min 7 68 max. flow 68 12 r/min 66 max. flow 12 r/min 66 64 max. flow 64 62 62 6 12 r/min min. flow 12 r/min min. flow 6 58 5 1 15 2 (7) (15) (22) (29) 58 5 Outlet 1 Pressure 15 ( 2 (7) (15) (22) (29) 25 (36) 25 (36) Delivery and Efficiency at 18 r/min, 5ϒC (12ϒF), and 1. absolute ( psi gauge) Inlet Delivery 1 and Efficiency at 18 r/min, 5ϒC (12ϒF), and Volumetric 1. Efficiency absolute ( psi gauge) Inlet 1 9 Volumetric Efficiency 8 9 7 8 Efficiency Efficiency % % 6 7 5 6 4 5 3 4 2 3 1 2 1 5 1 15 2 (7) (15) (22) (29) 5 Outlet Pressure 1 15 ( 2 (7) (15) (22) (29) 15 (4) 125 15 (33) (4) 1 125 (26) (33) 75 1 (2) (26) 5 75 (13) (2) 25 5 (7) (13) 25 (7) 25 (36) 25 (36) Delivery Delivery l/min l/min (USgpm) (USgpm) Noise Noise Level Level dba dba Typical Noise Levels at 15 and 1 r/min. with Petroleum Oil (1W) at 5 C (12 F) Typical and Noise 1. Levels absolute at 15 ( and psi 1 gauge) r/min. Inletwith 72 Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 72 7 7 68 68 66 664 64 62 62 6 6 58 15 r/min max. flow 15 r/min max. flow 1 r/min min. flow 1 r/min min. flow 1 r/min max. flow 1 r/min max. flow 15 r/min min. flow 15 r/min min. flow 58 56 5 1 15 2 56 (7) (15) (22) (29) 5 Outlet 1 Pressure 15 ( 2 Sound (7) pressure (15) data (22) (29) equivalent Outlet to NFPA. Pressure ( Sound pressure data equivalent to NFPA. 25 (36) 25 (36) Torque Torque Nm (in.lb.) Nm (in.lb.) Torque and Power at 18 r/min, 5ϒC (12ϒF), and 1. absolute ( psi gauge) Inlet Torque and Power at 18 r/min, 5ϒC (12ϒF), 35 (397) and 1. absolute ( psi gauge) Inlet 35 (397) 3 (2655) 3 (2655) 25 (2212) 25 (2212) 2 (177) Torque, Torque, Power Power kw (hp) kw (hp) 2 (177) 15 (1327) 75 (11) Power, 15 (1327) 75 (11) 1 (885) Power, 5 (67) 1 (885) 5 (67) 5 (442) Torque, 25 (34) Cut-off 5 (442) Torque, 25 (34) Cut-off 5 1 15 2 25 (7) (15) (22) (29) (36) Outlet 5 Pressure 1 15 (7) (15) 2 (22) (29) ( 25 (36) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 51

Performance Industrial PVM81 Delivery and Efficiency at 15 r/min, 5ϒC (12ϒF), and 1. absolute ( psi gauge) Inlet Delivery 1 and Efficiency at 15 r/min, 5ϒC (12ϒF), and 1. absolute ( psi gauge) Inlet Volumetric Efficiency 1 9 Volumetric Efficiency 8 9 7 8 Efficiency Efficiency % % 6 7 5 6 4 5 3 4 2 3 1 2 1 5 1 15 2 (7) (15) (22) (29) 5 1 15 2 (7) Outlet (15) Pressure (22) ( (29) 125 (33) 1 125 (26) (33) 75 1 (2) (26) 5 75 (13) (2) 25 5 (7) (13) 25 (7) 25 (36) 25 (36) Delivery Delivery l/min l/min (USgpm) (USgpm) Efficiency Efficiency % % Delivery and Efficiency at 12 r/min, 5ϒC (12ϒF), Delivery and and 1. Efficiency absolute at 12 ( psi r/min, gauge) 5ϒC Inlet (12ϒF), 1 and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Volumetric Efficiency 9 8 8 7 7 6 6 5 125 (33) 5 125 (33) 4 1 (26) 4 1 (26) 3 75 (2) 3 75 (2) 2 5 (13) 2 5 (13) 1 25 (7) 1 25 (7) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) Delivery Delivery l/min l/min (USgpm) (USgpm) Efficiency Efficiency % % Deli Deliv 1 1 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 Torque Torque Nm Nm (in.lb.) (in.lb.) Torque and Power at 15 r/min, 5ϒC (12ϒF), and 1. absolute ( psi gauge) Inlet Torque and Power at 15 r/min, 5ϒC (12ϒF), 35 (397) and 1. absolute ( psi gauge) Inlet 35 (397) 3 (2655) 3 (2655) 25 (2212) 25 (2212) 2 (177) 2 (177) 15 (1327) 15 (1327) 1 (885) Torque, Torque, Power Power kw (hp) kw (hp) 75 (11) 75 (11) 5 (67) 1 (885) 5 (67) 5 (442) 25 (34) Power, 5 (442) 25 (34) Power, 5 1 Full 15 Stroke 2 25 (7) (15) (22) (29) (36) 5 1 15 2 25 (7) Outlet (15) Pressure (22) (29) ( (36) Torque Torque Nm Nm (in.lb.) (in.lb.) Torque and Power at 12 r/min, 5ϒC (12ϒF), Torque and 1. and Power absolute at 12 ( psi r/min, gauge) 5ϒC Inlet (12ϒF), 35 (397) and 1. absolute ( psi gauge) Inlet 35 (397) 3 (2655) 3 (2655) 25 (2212) Torque, 25 (2212) Torque, 2 (177) 2 (177) 15 (1327) 75 (11) 15 (1327) 75 (11) 1 (885) 5 (67) Power, 1 (885) 5 (67) Power, 5 (442) 25 (34) 5 (442) 25 (34) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) (29) ((36) Power Power kw kw (hp) (hp) Torque Torque Nm Nm (in.lb.) (in.lb.) In Inp 35 35 3 3 25 25 2 2 15 15 1 1 5 52 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Performance Industrial PVM81 ), F), Delivery Delivery l/min l/min (USgpm) (USgpm) (33) 5 (33) (26) (26) (2) (2) (13) (13) (7) (7) Delivery and Efficiency at 1 r/min, 5ϒC (12ϒF), Delivery and and 1. Efficiency absolute at ( 1 psi r/min, gauge) 5ϒC Inlet (12ϒF), and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 1 9 Volumetric Efficiency 9 8 8 7 7 6 6 5 125 (33) 5 125 (33) 4 1 (26) 4 1 (26) 3 75 (2) 3 75 (2) 2 5 (13) 2 5 (13) 1 25 (7) 1 25 (7) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) Efficiency Efficiency % % Delivery Delivery l/min l/min (USgpm) (USgpm) Case Flow l/min - (USgpm) Case Flow versus Outlet Pressure at 18 r/min, Full Flow, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 4. (1.6) 3.5 (.92) 3. (.79) 2.5 (.66) 2. (.53) 1.5 (.4) 1. (.26).5 (.13) 5 (7) 1 (15) 15 (22) 2 (29) Outlet Pressure - ( 25 (36) F), ϒF), Power Power kw kw (hp) (hp) 11) (11) 67) (67) 34) (34) Torque Torque Nm Nm (in.lb.) (in.lb.) Torque and Power at 1 r/min, 5ϒC (12ϒF), and Torque 1. and absolute Power at ( 1 psi r/min, gauge) 5ϒC Inlet (12ϒF), 35 (397) and 1. absolute ( psi gauge) Inlet 35 (397) 3 (2655) 3 (2655) 25 (2212) 25 (2212) Torque, Full Stroke 2 (177) Torque, 2 (177) 15 (1327) 75 (11) 15 (1327) 75 (11) 1 (885) 5 (67) 1 (885) Power, 5 (67) 5 (442) Full Stroke Power, 25 (34) 5 (442) 25 (34) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 Outlet (7) Pressure (15) (22) (29) ( (36) Power Power kw kw (hp) (hp) Case Flow l/min - (USgpm) 15 (3.96) 14 (3.7) 12 (3.17) Case Flow versus Outlet Pressure at Cutoff, 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 21 (5.55) 2 (5.28) 19 (5.2) 18 (4.76) 17 (4.49) 16 (4.23) 13 (3.43) 11 (2.91) 5 (7) 1 (15) 15 (22) 2 (29) Outlet Pressure - ( 25 (36) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 53

Delivery Delivery l/min l/min (USgpm) (USgpm) Performance Mobile PVM81 Noise Level dba 82 78 74 7 66 62 58 Typical Noise Levels at 24 & 6 r/min with Petroleum Oil (1W) at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 24 r/min max. flow 6 r/min max. flow 24 r/min min. flow Noise Level dba 82 78 7 54 5 1 15 2 (7) (15) (22) (29) 66 Sound pressure data equivalent to NFPA. 62 6 r/min 74min. flow 58 Typical Noise Levels at 24 & 6 r/min with Petroleum Oil (1W) at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 25 (36) 24 r/min max. flow 6 r/min max. flow 24 r/min min. flow 6 r/min min. flow 54 5 1 15 2 (7) (15) (22) (29) Sound pressure data equivalent to NFPA. 25 (36) versus Speed at 93 C (2 F) and 1. absolute ( psi gauge) inlet Delivery and Case Flow versus Speed at 93 C (2 F), Full Flow 1. absolute ( psi gauge) Inlet (%) 1 95 9 85 15 (22 1 (145 5 (725 8 75 23 (33 1 7 2 (29 65 95 6 9 55 85 8 5 5 1 15 2 25 75 Speed r/min 7 65 (%) 6 55 2 (53) 18 (48) 16 (42) 4 (11) 2 (5) 5 (725 Case 2 (.53) 12 Flow(32) 3 23 (33 1 (26) 5 1 15 2 25 3 2 (29 Speed (r/min) 8 (21) 6 (16) 54 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 5 14 (37) versus Speed 5 (725 Delivery and Cas at 93 C (2 F) and 1. absolute Delivery at 93 C (2 F), Ful (12 psi (32) gauge) inlet 21 (3 Case Flow ( psi g Delivery l/min 1 1 (26) 2 (53) (USgpm) (145 8 (21) 5 (725 21 (3 Case 18 Flow (48) 8 (2.11) 6 (16) 16 (42) 6 (1.59) 15 (22 5 1 15 2 25 3 14 (37) 4 (1.6) 4 (11) 5 De 21 2 (5) 5 ba

Performance Mobile PVM81 Torque Torque Torque Nm Nm (in.lb.) Nm (in.lb.) Torque (in.lb.) Nm (in.lb.) Torque versus Speed at at 93 C 93 C (2 F), Full Full Flow Flow and and 1. 1. absolute ( ( psi psi gauge) Inlet Inlet 35 35 (2655) Torque versus Speed at at 93 C (2 F), Full Flow and 1. absolute ( ( psi gauge) Inlet 3 3 (2655) 35 (2655) 23 23 (33 (33 25 25 3 (2212) (2655) 2 25 2 (2212) (177) 15 15 2 (1327) (177) 1 15 1 (885) (1327) (885) 1 (15 5 5 (725 (725 5 5 1 (442) (442) (885) 17 17 (25 (25 5 5 (725 5 5 (442) 5 5 1 115 152 225 253 17 17 (25 Speed (r/min) 5 1 15 2 25 3 Speed (r/min) 21 21 (3 (3 23 (33 21 (3 15 15 (22 (22 1 15 1 (15 (22 (15 Power Power Power kw kw (hp) (hp) kw (hp) Power kw (hp) Power versus Speed at at 93 C 93 C (2 F), Full Full Flow Flow and and 1. 1. absolute ( ( psi psi gauge) Inlet Inlet Power versus Speed at at 93 C (2 F), 1 1 (134) (134) Full Flow and 1. absolute ( ( psi gauge) Inlet 9 9 (121) (121) 1 (134) 8 8 (17) (17) 9 9 (121) 23 23 (33 (33 7 7 (94) (94) 2 2 (29 (29 8 8 (17) 6 6 (8) (8) 23 (33 7 7 (94) 5 5 (67) (67) 15 2 15 (22 (29 (22 6 6 (8) 4 4 (54) (54) 1 1 5 5 (67) 15 (15 (15 (22 3 3 (4) (4) 4 4 (54) 2 2 (27) (27) 5 1 5 (725 (725 (15 3 3 (4) 1 1 (13) (13) 17 17 (25 (25 2 2 (27) 5 5 (725 1 1 (13) 5 5 1 115 15 2 225 25 17 17 3 3 (25 Speed (r/min) 5 1 15 2 25 3 Speed (r/min) Torque Torque Torque Nm Nm (in.lb.) Nm (in.lb.) Torque (in.lb.) Nm (in.lb.) Torque and and Case Case Flow Flow versus Speed at at 93 C 93 C (2 F), Load Load Sense Standby and and 1. 1. absolute ( ( psi psi gauge) Inlet Inlet Torque and Case Flow versus Speed at at 93 C 99 (8) (8) (2 F), Load Sense Standby and 1. absolute 2 2 ( (3 ((3 psi gauge) Inlet 88 (71) (71) diff. diff. Torque 99 (8) 77 (62) (62) 2 2 (3 88 (71) diff. Torque 11 11 (16 (16 diff. diff. 66 (53) (53) Torque Case Case 77 (62) Flow Flow l/min l/min 55 (44) (44) 11 11 (16 diff. (USgpm) 66 (53) Torque Case 44 (35) (35) 1. 1. Flow (2.64) (2.64) l/min 55 (44) (USgpm) 2 2 (3 (3 33 (27) (27) 8. 8. (2.11) (2.11) diff. diff. Case Case Flow Flow 44 (35) 1. (2.64) 22 (18) (18) 6. 6. (1.59) (1.59) 2 2 (3 11 11 (16 (16 diff. diff. 33 (27) 8. (2.11) 1 (9) diff. Case Flow Case Case Flow Flow 1 (9) 4. 4. (1.6) (1.6) 22 (18) 6. (1.59) 11 11 (16 diff. 2. 2. (.53) (.53) Case Flow 11 (9) (9) 5 5 1 1 15 15 2 2 25 25 3 3 4. (1.6) Speed (r/min) 2. (.53) 5 1 15 2 25 3 Speed (r/min) Torque Torque Torque Nm Nm (in.lb.) Nm (in.lb.) Torque (in.lb.) Nm (in.lb.) Torque and and Case Case Flow Flow versus Speed at at 93 C 93 C (2 F), Pressure Limit Limit Cut-off and and 1. 1. absolute ( ( psi psi gauge) Inlet Inlet Torque and Case Flow versus Speed at at 93 C 8 8 (78) (2 F), (78) Pressure Limit Cut-off and 1. absolute ( ( psi gauge) Inlet 7 7 (619) (619) 8 8 (78) 21 21 (3 Torque 15 15 6 6 (531) (531) (22 7 7 (619) 21 (3 Torque 5 5 (442) (442) 15 Torque 6 6 (531) (22 4 4 (354) (354) 5 5 (442) 21 Torque 21 (3 3 3 (265) (265) 4 4 (354) Case Case 8. 8. (2.11) (2.11) Flow 21 Flow 2 2 (177) (177) (3 6. 6. (1.59) (1.59) 3 3 (265) Case 8. (2.11) 15 15 1 (88) Flow 4. 4. (1.6) (1.6) 1 (88) 2 2 (177) (22 6. (1.59) 2. 2. (.53) (.53) Case Case Flow Flow 15 4. (1.6) 1 1 (88) (22 5 5 1 1 15 15 2 2 25 25 3 3 2. (.53) Case Flow Speed (r/min) 5 1 15 2 25 3 Speed (r/min) Case Flow Case Case Flow l/min Flow l/min (USgpm) l/min (USgpm) Case Flow (USgpm) l/min (USgpm) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 55

Performance Industrial PVM98 Noise Level dba Noise Level dba Typical Noise Levels at 18 and 12 r/min Delivery and Efficiency at 18 r/min with Petroleum Oil (1W) at 5 C (12 F) 5 C (12 F) and 1. absolute ( psi gauge) Inlet and 1. absolute ( psi gauge) Inlet 1 78 9 Volumetric Efficiency 18 r/min Delivery and Efficiency at 18 r/min 76 Max. Flow 5 C (12 F) and Overall 1. Efficiency absolute ( psi gauge) Inlet 8 1 74 18 r/min Min. Flow 7 9 Volumetric Efficiency 72 12 r/min 6 8 7 Max. Flow 68 5 7 66 4 6 2 (53) 64 3 5 15 (4) 62 2 4 1 (26) 2 (53) 6 1 3 5 (13) 15 (4) 58 12 r/min Min. Flow 2 5 1 15 2 25 3 (7) (15) (22) (29)(36) (44)(5) 35 1 (26) 56 5 1 15 2 25 3 1 5 (13) (7) (15) (22) (29) (36) (44) Outlet Pressure - ( 5 1 15 2 25 3 Torque (7) and (15) Power (22) at 18 (29) r/min (36) (44)(5) 35 Sound pressure data equivalent to NFPA) 5 C (12 F) and 1. absolute ( psi gauge) Inlet Outlet Pressure - ( 55 (4867) Typical Noise Levels at 15 and 1 r/min 5 (4425) Torque and Power at 18 r/min with Petroleum Oil (1W) at 5 C (12 F) 5 C (12 F) and 1. Torque, absolute ( psi gauge) Inlet and 1. absolute ( psi gauge) Inlet 45 (3982) 55 (4867) 72 4 (354) 5 (4425) 15 r/min 7 35 (397) Torque, Max. Flow 45 (3982) 68 3 (2655) 4 (354) 15 r/min 66 25 (2212) 35 (397) Power, Min. Flow 64 1 r/min 2 (177) 3 (2655) 1 (134) Max. Flow 62 15 (1327) 25 (2212) Power, 75 (11) 6 1 (885) 2 (177) 5 (67) 1 (134) 5 (442) 15 (1327) Torque, 25 (34) 75 (11) 58 Cut-off 1 (885) 56 5 1 15 2 25 3 35 5 (67) (7) (15) (22) (29) (36) (44) (5) 5 (442) Outlet Pressure - ( Torque, 25 (34) 54 1 r/min Cut-off Min. Flow 52 5 1 15 2 25 3 35 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) (5) (7) (15) (22) (29) (36) (44) Outlet Pressure - ( Torque - Nm (in.lb.) Efficiency - % Torque - Nm (in.lb.) Efficiency - % Delivery -l/min (USgpm) Power - kw (hp) Delivery -l/min (USgpm) Power - kw (hp) 56 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Performance Industrial PVM98 Efficiency % Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Delivery and Efficiency at 15 r/min 5 C (12 F) and Overall 1. Efficiency absolute ( psi gauge) Inlet 8 1 Volumetric Efficiency 7 6 9 8 5 4 3 2 1 2 (53) 15 (4) 1 2 (26) (53) 5 (13) 15 (4) 2 1 (26) 5 1 15 2 25 3 35 1(7) (15) (22) (29) (36) (44) (5) 5 (13) 5 Torque 1 and Power 15 2 at 1525 r/min3 35 5 C (12 F) (7) and (15) 1. (22) absolute (29) ( psi (36) gauge) (44) Inlet (5) 55 (4867) 5 (4425) Torque and Power at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 45 (3982) 55 (4867) Torque, 4 (354) 5 (4425) 35 (397) 45 (3982) 3 (2655) 4 (354) Torque, 25 (2212) 35 (397) 2 (177) Power, 1 (134) 3 (2655) 15 (1327) 75 (11) 25 (2212) 1 (885) 2 (177) 5 (442) 15 (1327) Power, 5 (67) 1 (134) 25 (34) 75 (11) 1 (885) 5 1 15 2 25 3 35 5 (67) (7) (15) (22) (29) (36) (44) (5) 5 (442) 25 (34) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Efficiency % 7 6 5 4 3 Power kw (hp) Power kw (hp) Efficiency % Delivery and Efficiency at 12 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Delivery and Efficiency at 12 r/min 5 C (12 F) Overall and 1. Efficiency absolute ( psi gauge) Inlet 8 1 Volumetric Efficiency 7 9 6 8 5 4 3 2 2 (53) 15 (4) 1 2 (26) (53) 1 3 5 (13) 15 (4) 2 1 (26) 5 1 15 2 25 3 35 1(7) (15) (22) (29) (36) (44) (5) 5 (13) 5 1 15 2 25 3 35 (7) Torque (15) and (22) Power (29) at 12 (36) r/min (44) (5) 5 C (12 F) and 1. Outlet Pressure absolute ( psi ( gauge) Inlet 55 (4867) 5 (4425) Torque and Power at 12 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 45 (3982) Torque, 55 (4867) 4 (354) 5 (4425) 35 (397) 45 (3982) Torque, 3 (2655) 4 (354) 25 (2212) 35 (397) 2 (177) 1 (134) 3 (2655) Power, 15 (1327) 75 (11) 25 (2212) 1 (885) 2 (177) 5 (442) 15 (1327) Power, 5 (67) 1 (134) 25 (34) 75 (11) 1 5 (67) (885) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44)(5) 5 (442) 25 (34) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44)(5) Efficiency % 7 6 5 4 Power kw (hp) Power kw (hp) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 57

Performance Industrial PVM98 Efficiency % Delivery and Efficiency at 1 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Volumetric Delivery Efficiency and Efficiency at 1 r/min 9 5 C (12 F) Overall and 1. Efficiency absolute ( psi gauge) Inlet 1 8 Volumetric Efficiency 7 6 5 9 8 7 4 6 2 (53) 5 3 15 (4) 4 2 (53) 2 1 (26) 1 3 15 (4) 5 (13) 2 1 (26) 5 1 15 2 25 3 35 1 (7) (15) (22) (29) (36) (44)(5) 5 (13) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44)(5) Torque Outlet and Pressure Power at 1 ( r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 55 (4867) 5 (4425) Torque and Power at 1 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 45 (3982) 55 (4867) 4 (354) 5 (4425) 35 (397) 45 (3982) 3 (2655) 4 (354) 25 (2212) 35 (397) 2 (177) 3 (2655) 1 (134) 15 (1327) 25 (2212) 75 (11) Power, 1 2 (885) (177) 5 (67) 1 (134) 5 15 (442) (1327) Power, 25 (34) 75 (11) 1 (885) 5 (67) 5 1 15 2 25 3 35 5 (442) (7) (15)(22) (29) (36) (44) (5) 25 (34) Outlet Pressure - ( 5 1 15 2 25 3 35 (7) (15)(22) (29) (36) (44) (5) Outlet Pressure - ( Efficiency % Torque, Torque, Power kw (hp) Power kw (hp) Case Flow Case - l/min Flow (USgpm) - l/min (USgpm) Case Flow Case - l/min Flow (USgpm) - l/min (USgpm) Case Flow Versus Outlet Pressure at Full Flow, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 5,5 (1.45) 5, Case (1.32) Flow Versus Outlet Pressure at Full Flow, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 4,5 (1.19) 5,5 (1.45) 4, (1.6) 5, (1.32) 3,5 (.92) 4,5 (1.19) 3, (.79) 4, (1.6) 2,5 (.66) 3,5 (.92) 2, (.53) 3, (.79) 1,5 (.4) 2,5 (.66) 1, (.26) 2, (.53),5 (.13) 1,5 (.4) 1, (.26) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44)(5),5 (.13) Outlet Pressure - ( Case Flow 5 Versus 1 Outlet 15 Pressure 2 25 at Cutoff, 318 35 r/min 5 C (7) (12 (15) F) and (22) 1. (29) absolute (36) ( psi (44) gauge) (5) Inlet 25 (6.6) Outlet Pressure - ( 24 (6.34) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 25 (6.6) 23 (6.8) 24 (6.34) 22 (5.81) 23 (6.8) 21 (5.55) 22 (5.81) 2 (5.28) 21 (5.55) 19 (5.2) 2 (5.28) 18 (4.76) 19 (5.2) 17 (4.49) 5 1 15 2 25 18 (4.76) (7) (15) (22) (29) (36) Outlet Pressure - ( 3 (44)(5) 35 17 (4.49) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44)(5) 35 Outlet Pressure - ( 58 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Overall Efficiency (%) (%) Performance Mobile PVM98 Noise Noise Level Level dba dba 86 86 84 84 82 82 8 8 78 78 76 76 74 74 72 72 7 7 68 68 66 Typical Noise Levels at 2 and 6 r/min with petroleum oil (1 W) @ 93 C (2 F) Typical Noise Levels at 2 and 6 r/min and 1. absolute ( psi gauge) inlet with petroleum oil (1 W) @ 93 C (2 F) and 1. absolute ( psi gauge) inlet 6 r/min Min. flow 6 r/min Min. flow 2 r/min Min. flow 2 r/min Min. flow 2 r/min Max. flow 2 r/min Max. flow 6 r/min Max. flow 6 r/min Max. flow 66 64 5 1 15 2 25 64 (7) (15) (22) (29) (36) 5 Outlet 1 Pressure 15 2( 25 (7) (15) (22) (29) (36) Sound pressure data equivalent Outlet to Pressure NFP ( Sound pressure data equivalent to NFP 3 (44) 3 (44) Delivery and Case Flow Versus Speed Delivery and @ 93 C Case (2 F), Flow Versus full flow Speed and @ 1. 93 C (2 F), absolute full ( flow and gauge Inlet 22 (58) 1. absolute ( gauge Inlet 22 (58) 2 (53) 5 (7, 2 (53) 5 Delivery (7, 18 (48) Delivery 18 (48) 16 (42) 16 (42) 14 (37) 28 (4, Delivery 14 (37) 28 (4, 12 (32) Delivery 12 (32) 1 (26) 1 (26) 28 (4, 8 (21) 28 Case (4 flow, 8 (2.1) 8 (21) Case flow 8 (2.1) 6 (16) 6 (1.6) 6 (16) 6 (1.6) 4 (11) 5 (7, 4 (1.1) 4 (11) 5 Case (7 flow, 4 (1.1) 2 (5) Case flow 2 (.5) 2 (5) 2 (.5) 5 1 15 2 25 5 1 Speed 15 r/min 2 25 Speed r/min Case Flow l/min (USgpm) 95 95 9 9 Versus Speed @ 93 C (2 F) and 1. absolute Versus Speed ( psi gauge) inlet @ 93 C (2 F) and 1. absolute ( psi gauge) inlet 85 1 (15 85 1 15 (15 (22 15 (22 2 (29 8 8 2 (29 5 (7 5 (7 25 (36 75 25 28 (36 (4 75 28 32 (4 (46 7 32 (46 5 1 15 2 25 7 Speed r/min 5 1 15 2 25 Speed r/min Torque Versus Speed @ Torque 93 C (2 F), Versus Speed full flow and @ 93 C 1. (2 F), absolute full ( flow psi and gauge) inlet 6 (531) 1. absolute ( psi gauge) inlet 6 (531) 54 (4779) 54 (4779) 32 (46 48 (4248) 32 (46 48 (4248) 28 (4 42 (3717) 28 (4 25 (36 42 (3717) 36 (3186) 25 (36 36 (3186) 2 (29 3 (2655) 2 (29 3 (2655) 24 (2124) 15 (22 24 (2124) 15 (22 18 (1593) 18 (1593) 12 (162) 12 (162) 1 (15 1 (15 5 (7 6 (531) 5 (7 17 (25 6 (531) 17 (25 5 1 15 2 25 3 5 1 15 Speed 2 r/min25 3 Speed r/min EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 59

Power Power KW KW (hp) (hp) Torque Torque Nm Nm (in.lb.) (in.lb.) Case Flow l/min (USgpm) Performance Mobile PVM98 Power Versus Speed @93 C Power (2 F), Versus full flow Speed and 1. @93 C absolute (2 F), ( psi full gauge) flow and inlet 13 (174) 1. absolute ( psi gauge) inlet 13 (174) 12 (161) 32 (46 12 (161) 11 (148) 32 (46 11 (148) 1 (134) 28 (4 1 (134) 28 (4 25 (36 9 (121) 25 (36 9 (121) 8 (17) 8 (17) 2 (29 7 (94) 2 (29 7 (94) 6 (8) 6 (8) 15 (22 5 (67) 15 (22 5 (67) 4 (54) 1 (15 4 (54) 3 (4) 1 (15 3 (4) 2 (27) 5 (7 2 (27) 5 (7 1 (13) 17 (25 1 (13) 17 (25 5 1 15 2 25 3 5 1 15 2 25 3 Speed r/min Speed r/min Torque and Case Flow Versus Speed @ Torque 93 C (2 F), and Case load Flow sense Versus standby Speed and @ 1. 93 C (2 F), absolute load ( psi sense gauge) standby inlet 11 (77) and 1. absolute ( psi gauge) inlet 11 (77) 1 (88) 2 (3) differential 1 (88) 2 Torque (3) differential Torque 9 (8) 9 (8) 8 (71) 8 (71) 11 (16) differential 9. (2.38) 7 (62) 11 (16) differential 9. (2.38) 7 (62) Torque Torque 8.5 (2.25) 6 (53) 8.5 (2.25) 6 (53) 8. (2.11) 5 (44) 2 (3) differential 8. (2.11) 5 (44) Case 2 Flow (3) differential 7.5 (1.98) 4 (35) Case Flow 7.5 (1.98) 4 (35) 7. (1.85) 7. (1.85) 3 (27) 6.5 (1.72) 3 (27) 11 (16) differential 6.5 (1.72) 2 (18) Case 11 Flow (16) differential 6. (1.59) 2 (18) Case Flow 6. (1.59) 1 (9) 5.5 (1.45) 1 (9) 5 1 15 2 255.5 (1.45) 5 Speed 1 r/min 15 2 25 Speed r/min Torque Nm (lb.in.) Case Case Flow Flow (l/min (l/min (USgpm) (USgpm) 24 (2124) 22 (1947) 2 (177) 18 (1593) 16 (1416) 14 (1239) 12 (162) 28 (4 3 (7.9) 1 (885) Case Flow 25 (6.6) 8 (78) 2 (5.3) 6 (531) 15 (22 15 (22, Case Flow 15 (4.) 4 (354) Torque 1 (2.6) 2 (177) 5 (1.3) 5 1 15 2 25 Case Flow l/min (USgpm) Case Flow at 22 r/min, Full Flow 93 C (2 F), 1. absolute ( psi gauge) Inlet 16 (4.2) 14 (3.7) 12 (3.2) 1 (2.6) 8 (2.1) 6 (1.6) 4 (1.) 2 (.5) Torque and Case Flow Versus Speed @ 93 C (2 F), cut-off and 1. absolute ( psi gauge) inlet 28 (4 Torque Speed r/min 5 1 15 2 25 3 (7) (15)(22) (29)(36) (44)(5) 35 Case Flow at 22 r/min, Minimum Flow 935C (25F), 1. absolute ( psi gauge) Inlet 32 (8.4) 28 (7.4) 24 (6.3) 2 (5.3) 16 (4.2) 12 (3.2) 5 1 15 2 25 3 35 (7) (15)(22) (29)(36) (44)(5) Case Flow l/min (USgpm) 6 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Performance Industrial PVM16 Noise Level dba Typical Noise Levels at 18 and 12 r/min. Typical Noise Levels at 18 and 12 r/min. with Petroleum Oil (1W) at 5 C (12 F) with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet and 1. absolute ( psi gauge) Inlet 8 8 78 18 r/min 78 max. 18 flow r/min max. flow 76 76 74 74 72 18 r/min 72 min. 18 flow r/min 12 r/min min. flow min. 12 flow r/min 7 min. flow 7 68 68 12 r/min 66 12 r/min 66 max. flow max. flow 64 64 62 62 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) Outlet Pressure ( Delivery and Efficiency at at 18 r/min, 5ϒC (12ϒF), and 1. 1. absolute ( ( psi gauge) Inlet 1 Volumetric Efficiency 9 9 8 8 7 7 6 6 Efficiency Efficiency - % 5 5 4 4 3 3 2 2 1 (26) 1 1 5 5 (13) 5 5 (7) 2 (53) 15 (4) 1 (15) 15 2 (22) (29) Outlet Pressure - - ( Delivery Delivery l/min l/min (USgpm) (USgpm) 25 (66) 25 (36) Noise Level dba 76 76 74 74 72 72 7 7 68 68 66 66 64 64 62 62 Typical Noise Levels at 15 and 1 r/min. Typical Noise Levels at 15 and 1 r/min. with Petroleum Oil (1W) at 5 C (12 F) with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet and 1. absolute ( psi gauge) Inlet 15 r/min min. 15 flow r/min min. flow 1 r/min min. 1 flow r/min min. flow 1 r/min max. 1 flow r/min max. flow 15 r/min max. 15 flow r/min max. flow 6 6 58 58 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) Sound pressure Outlet data Pressure ( Sound pressure data equivalent to NFPA. equivalent to NFPA. Torque Torque Nm Nm (in.lb.) (in.lb.) Torque and Power at at 18 r/min, 5ϒC (12ϒF), and 1. 1. absolute ( ( psi gauge) Inlet 5 (4425) 45 (3982) 4 (354) 35 (397) 3 (2655) 25 (2212) 2 (177) 15 (1327) Torque, Power, Power Power kw kw (hp) (hp) 1 (134) 75 75 (11) 1 (885) Torque, 5 5 (67) Cut-off 5 5 (442) 25 25 (34) 5 5 1 15 2 25 (7) (15) (22) (29) (36) Outlet Pressure - - ( EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 61

Performance Industrial PVM16 Delivery Delivery and and Efficiency Efficiency at at 15 15 r/min, r/min, 5ϒC 5ϒC (12ϒF), (12ϒF), and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 1 1 Volumetric Volumetric Efficiency Efficiency 9 9 Overall Efficiency 8 8 Efficiency % 7 7 6 6 5 5 4 4 3 3 2 2 5 5 1 1 15 15 2 2 (7) (7) (15) (15) (22) (22) (29) (29) Outlet Outlet Pressure Pressure ( ( 25 25 (36) (36) Delivery l/min l/min (USgpm) 25 25 (66) (66) 2 2 (53) (53) Delivery Delivery (effective (effective flow) flow) 15 15 (4) (4) 1 1 (26) (26) 1 1 5 5 (13) (13) Delivery and Efficiency at 12 r/min, 5ϒC (12ϒF), Delivery and and 1. Efficiency absolute at ( 12 psi r/min, gauge) 5ϒC Inlet (12ϒF), and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency 9 Volumetric Efficiency 9 8 8 7 7 6 6 5 25 (66) 5 4 25 (66) 2 (53) 3 4 15 2 (4) (53) 3 2 15 (4) 1 (26) 2 1 1 (26) 5 (13) 1 5 (13) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) (29) ( (36) Efficiency Efficiency % % Delivery Delivery l/min l/min (USgpm) (USgpm) Delive Deliv 1 1 V 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 Efficiency Efficiency % % ) Torque Nm Nm (in.lb.) (in.lb.) Torque Torque and and Power Power at at 15 15 r/min, r/min, 5ϒC 5ϒC (12ϒF), (12ϒF), and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 5 5 (4425) (4425) 45 45 (3982) (3982) 4 4 (354) (354) 35 35 (397) (397) 3 3 (2655) (2655) Torque, Torque, Full Full Stroke Stroke Power Power kw kw (hp) (hp) 25 25 (2212) (2212) 2 2 (177) 1 (177) 1 (134) (134) 15 15 (1327) (1327) Power, 75 75 (11) Power, (11) Full Full Stroke Stroke 1 1 (885) 5 (885) 5 (67) (67) 5 5 (442) 25 (442) 25 (34) (34) 5 5 1 1 15 15 2 2 25 25 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) Outlet Outlet Pressure Pressure ( ( Torque Torque Nm Nm (in.lb.) (in.lb.) Torque and Power at 12 r/min, 5ϒC (12ϒF), and Torque 1. and absolute Power at ( 12 psi r/min, gauge) 5ϒC Inlet (12ϒF), 5 (4425) and 1. absolute ( psi gauge) Inlet 5 (4425) 45 (3982) 45 (3982) 4 (354) 4 (354) Torque, 35 (397) Full Stroke Torque, 35 (397) 3 (2655) 3 (2655) 25 (2212) 25 (2212) 2 (177) 1 (134) 2 (177) 1 (134) 15 (1327) 75 (11) 15 (1327) Power, 1 (885) 75 (11) Power, 5 (67) 1 (885) 5 (442) 5 (67) 25 (34) 5 (442) 25 (34) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 Outlet (7) Pressure (15) (22) (29) ( (36) Power Power kw kw (hp) (hp) Torque Torque Nm Nm (in.lb.) (in.lb.) 5 5 45 4 4 4 35 3 3 3 25 2 2 2 15 1 62 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Performance Industrial PVM16 66) ) 53) ) 4) ) 26) ) 3) Delivery and Efficiency at 1 r/min, 5ϒC (12ϒF), Delivery and and 1. Efficiency absolute at 1 ( psi r/min, gauge) 5ϒC Inlet (12ϒF), and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency 9Volumetric Efficiency 9 8 8 7 7 6 6 5 25 (66) 5 25 (66) 4 2 (53) 4 2 (53) 3 15 (4) 3 15 (4) 2 1 (26) 2 1 (26) 1 5 (13) 1 5 (13) 5 1 15 2 25 5 (7) 1 (15) 15 (22) 2 (29) 25 (36) (7) Outlet (15) Pressure (22) (29) ( (36) Efficiency % Efficiency % Case Case Flow Flow l/min l/min (USgpm) (USgpm) Case Flow versus Outlet Pressure at 18 r/min, Full Flow, Case 5 C Flow (12 F), versus and Outlet 1. Pressure absolute at 18 ( psi r/min, gauge) Full Inlet Flow, 4. (1.6) 5 C (12 F), and 1. absolute ( psi gauge) Inlet 4. (1.6) 3.5 (.92) 3.5 (.92) 3. (.79) 3. (.79) 2.5 (.66) 2.5 (.66) 2. (.53) 2. (.53) 1.5 (.4) 1.5 (.4) 1. (.26) 1. (.26).5 (.13).5 (.13) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) ϒF), F), Power kw (hp) (134) 134) 11) 1) 67) 7) 34) 4) Torque and Power at 1 r/min, 5ϒC (12ϒF), Torque and 1. and Power absolute at 1 ( psi r/min, gauge) 5ϒC Inlet (12ϒF), 5 (4425) and 1. absolute ( psi gauge) Inlet 5 (4425) 45 (3982) 45 (3982) 4 (354) 4 (354) Torque, 35 (397) Full Torque, Stroke 35 (397) 3 (2655) 3 (2655) 25 (2212) 25 (2212) 2 (177) 1 (134) 2 (177) 1 (134) 15 (1327) 75 (11) 15 (1327) Power, 75 (11) 1 (885) Full Power, Stroke 5 (67) 1 (885) 5 (67) 5 (442) 25 (34) 5 (442) 25 (34) 5 1 15 2 25 5 (7) (15) 1 15 (22) 2 (29) 25 (36) (7) Outlet (15) Pressure (22) (29) ( (36) Power kw (hp) Power kw (hp) Case Case Flow Flow l/min l/min (USgpm) (USgpm) Case Flow versus Outlet Pressure at Cutoff, 18 r/min, Case 5 C Flow (12 F), versus and Outlet 1. Pressure absolute at ( Cutoff, psi gauge) 18 r/min, Inlet 5 C (12 F), and 1. absolute ( psi gauge) Inlet 21 (5.55) 21 2 (5.55) (5.28) 2 19 (5.28) (5.2) 19 18 (5.2) (4.76) 18 17 (4.76) (4.49) 17 16 (4.49) (4.23) 16 15 (4.23) (3.96) 15 14 (3.96) (3.7) 14 13 (3.7) (3.43) 13 12 (3.43) (3.17) 12 11 (3.17) (2.91) 11 (2.91) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 63

(%) (%) Noise Level dba Noise Level dba Noise Level dba Performance Mobile PVM16 86 Typical Noise Typical Levels Noise at 22 Levels & 6 at 22 r/min & 6 r/min with Petroleum with Petroleum Oil (1W) at Oil 93 C (1W) (2 F) at 93 C (2 F) and 1. and absolute 1. ( absolute psi gauge) ( psi Inlet gauge) Inlet 86 82 78 74 7 66 62 58 82 22 r/min22 r/min max. flow max. flow 78 74 7 6 r/min min. flow 66 62 58 6 r/min min. flow 22 r/min22 r/min min. flow min. flow 6 r/min max. flow 54 54 5 1 5 15 1 2 15 25 2 (7) (15) (7) (22) (15) (29) (22) (36) (29) Outlet Pressure Outlet Pressure ( ( Sound pressure Sound data pressure data equivalent equivalent to NFPA. to NFPA. 86 82 6 r/min max. flow 78 74 62 58 Typical Noise Levels at 22 & 6 r/min with Petroleum Oil (1W) at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 22 r/min max. flow 25 7 (36) 6 r/min min. flow 66 22 r/min min. flow 6 r/min max. flow 54 5 1 15 2 (7) (15) (22) (29) Sound pressure data equivalent to NFPA. 25 (36) versus Speed versus at Speed at Delivery and Delivery Case Flow and Case versus Flow Speed versus at 93 C Speed (2 F), at 93 C (2 F), 93 C (2 F) 93 C and (2 F) 1. and absolute 1. ( absolute psi gauge) ( psi inlet gauge) inlet Full Flow 1. Full Flow absolute 1. ( absolute psi gauge) ( psi Inlet gauge) Inlet 24 (63) 24 (63) 1 22 (58) 22 (58) 95 1 1 5 (725 15 (145 2 (53) 5 (725 95 15 (145 2 (53) Delivery Delivery (22 (22 9 18 (48) 9 18 (48) 85 16 (42) 16 (42) 85 2 21 (3 Case Flow 2 versus Speed at 21 (3 Case Flow Delivery and C (29 (29 8 14 (37) 14 (37) Delivery l/min 8 5 (725 93 C (2 F) and 1. absolute ( psi gauge) inlet Delivery l/min Full Flow 23 (33 5 (725 (USgpm) (USgpm) 75 23 (33 12 (32) 12 (32) 75 24 (63) 21 7 1 1 (26) 1 (2.6) 21 1 (26) 1 (2.6) 7 22 (58) (3 (3 1 65 95 8 (21) 15 (145 2 8 (53) (2.11) 65 8 (21) 8 (2.11) 6 (22 6 (16) 21 (3 Case Flow 9 186 (48) (1.59) 6 6 (16) 21 (3 Case Flow 6 (1.59) 4 (11) 55 164 (42) (1.6) 85 4 (11) 4 (1.6) 55 2 5 (725 Case Flow 5 (29 2 (5) 5 (725 Case Flow 142 (37) (.53) 5 8 2 (5) 2 (.53) 5 (725 5 1 15 2 25 3 5 1 15 2 25 3 23 (33 12 (32) 75 5 1 5 15 1 2 15 25 2 25 Speed r/min Speed r/min 21 Speed (r/min) 1 (26) 7 Speed (r/min) (3 65 8 (21) 6 6 (16) 4 (11) 55 2 (5) 5 64 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 5 1 15 2 25 3

Performance Mobile PVM16 45 45 (3982) (3982) Torque versus Speed at at 93 C (2 F), Full Full Flow and and 1. 1. absolute ( ( psi psi gauge) Inlet 4 4 (354) (354) 23 23 (33 (33 45 45 (3982) 21 21 (3 (3 35 35 4 (397) (397) 23 2 23 2 (33 (29 (29 4 (354) 3 3 (2655) (2655) 21 21 (3 35 35 (397) 2 15 2 15 (29 (22 (22 25 3 3 25 (2212) (2655) (2212) 15 15 (22 25 2 25 2 (2212) (177) (177) 1 1 (15 (15 Torque Torque Nm (in.lb.) Nm (in.lb.) Torque versus Speed Speed at 93 C at 93 C (2 F), Power Power versus Speed Speed at 93 C at 93 C (2 F), Full Full Flow Flow and and 1. 1. absolute ( psi ( psi gauge) Inlet Inlet Full Full Flow Flow and and 1. 1. absolute ( psi ( psi gauge) Inlet Inlet 2 15 2 15 (177) (1327) (1327) 15 1 1 15 (1327) (885) (885) 1 1 5 (885) 5 (442) (442) 1 1 (15 5 5 (725 (725 5 17 5 17 (725 (25 (25 5 5 (442) 5 51 1 15 15 2 2 25 17 25 17 3 (25 3 Speed Speed (r/min) (r/min) 5 5 1 15 2 25 3 Speed (r/min) Power versus Speed at at 93 C (2 F), 1 1 Full (134) (134) Full Flow and and 1. 1. absolute ( ( psi psi 23 gauge) 23 (33 Inlet (33 9 9 (121) (121) 21 21 (3 (3 1 1 (134) 8 8 (17) (17) 23 15 23 15 (33 (22 (22 9 9 (121) 21 21 (3 7 7 (94) (94) 8 15 8 (17) 15 (22 6 6 (8) (8) 1 1 (15 (15 7 7 (94) (94) 5 5 (67) (67) 6 (8) 1 6 (8) 1 (15 4 4 (54) (54) 5 5 (67) (67) 3 3 (4) (4) 4 4 (54) (54) 5 5 (725 (725 2 2 (27) (27) 3 3 (4) (4) 1 1 (13) (13) 5 17 5 17 (725 (25 (25 2 2 (27) (27) 1 1 (13) (13) 5 51 1 15 15 2 2 25 17 25 17 3 (25 3 Power Power Power kw (hp) kw (hp) kw (hp) Power kw (hp) Speed Speed (r/min) (r/min) 5 5 1 15 2 25 3 Speed (r/min) Torque and and Case Case Flow Flow versus Speed Speed at 93 C at 93 C (2 F), Load Load Sense Sense Standby and and 1. 1. absolute ( psi ( psi gauge) Inlet Inlet Torque and and Case Flow versus Speed at at 93 C 12 (2 F), 12 (16) (16) Load Sense Standby and and 1. 1. absolute ( ( psi psi gauge) Inlet 11 (97) 11 (97) 12 12 (16) 2 2 (3 (3 1 1 (88) (88) diff. diff. Torque 11 11 (97) (97) 9 (8) 9 (8) 2 1 (88) 2 (3 1 (88) 8 (71) 8 (71) diff. diff. Torque Case Case 99 (8) (8) Flow Flow l/min l/min 7 (62) 7 (62) 11 11 (16 (16 diff. diff. (USgpm) 88 (71) (71) Torque Case 6 (53) 6 (53) Flow l/min 77 (62) (62) 11 11 (16 diff. diff. 9. 9. (2.38) (2.38) (USgpm) 5 (44) 5 (44) Torque 8.5 8.5 (2.25) (2.25) 66 (53) (53) 4 (35) 4 (35) 9. 9. (2.38) 8. 8. (2.11) (2.11) 55 (44) (44) 3 (27) 3 (27) 2 2 (3 (3 8.5 8.5 (2.25) 7.5 7.5 (1.98) (1.98) 44 (35) (35) diff. diff. Case Case Flow Flow 11 11 (16 (16 diff. diff. 2 (18) 2 (18) Case Case Flow Flow 8. 8. (2.11) 7. 7. (1.85) (1.85) 33 (27) (27) 2 2 (3 1 (9) 1 (9) 7.5 diff. 7.5 (1.98) diff. Case Flow 11 11 (16 diff. diff. 6.5 6.5 (1.72) (1.72) 22 (18) (18) Case Flow 7. 7. (1.85) 6. 6. (1.59) (1.59) 11 (9) (9) 5 5 1 1 15 15 2 2 25 25 6.5 6.5 (1.72) Speed Speed (r/min) (r/min) 6. 6. (1.59) 5 5 1 15 2 25 Speed (r/min) Torque Torque Nm (in.lb.) Nm (in.lb.) Torque and and Case Case Flow Flow versus Speed Speed at 93 C at 93 C (2 F), Pressure Limit Limit Cut-off and and 1. 1. absolute ( psi ( psi gauge) Inlet Inlet Torque and and Case Flow versus Speed at at 93 C 14 (2 F), 14 (1239) (1239) Pressure Limit Cut-off and and 1. 1. absolute ( psi 13 13 (115) (115) ( psi gauge) Inlet 14 14 (1239) 21 21 (3 (3 Torque 12 12 (162) (162) 13 13 11 (115) 11 (973) (973) 21 12 21 (3 Torque 12 1 (162) 1 (885) (885) 11 11 9 (973) 9 (796) (796) Case Case Flow Flow l/min l/min 1 1 8 (885) 8 (78) (78) 15 15 (22 (22 (USgpm) 9 Case 9 (796) Torque 7 7 (619) (619) Flow l/min 8 6 8 (78) 6 (531) (531) 15 15 (22 Torque (USgpm) 3 3 (7.9) (7.9) 7 5 7 (619) 5 (442) (442) 25 25 (6.6) (6.6) 21 21 (3 (3 Case Case Flow Flow 6 4 6 (531) 4 (354) (354) 3 2 3 2 (7.9) (5.3) (5.3) 5 3 5 (442) 3 (265) (265) 25 25 (6.6) 21 21 (3 Case Flow Flow 15 15 (4.) (4.) 4 2 4 (354) (177) 15 15 (22 (22 2 (177) 2 2 (5.3) Case Case Flow Flow 1 1 (2.6) (2.6) 3 3 1 (265) 1 (88) (88) 15 15 2 2 (177) 15 (22 15 5 (1.3) 5 (4.) (1.3) 1 Case Flow 1 (2.6) 1 1 (88) (88) 5 5 1 1 15 15 2 2 25 25 55 (1.3) Speed Speed (r/min) (r/min) 5 5 1 15 2 25 Speed (r/min) ( ( ( Torque Torque Torque Nm (in.lb.) Nm (in.lb.) Nm (in.lb.) ( EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 65

Performance Industrial PVM131 Noise Noise Level Level dba dba Noise Noise Level Level dba dba Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) Typical and Noise 1. Levels absolute at 18 ( psi and gauge) 12 Inlet r/min 82 with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 82 8 18 r/min Max. Flow 8 78 18 r/min Max. Flow 78 76 18 r/min Min. Flow 76 74 18 r/min Min. Flow 74 72 12 r/min 72 7 Max. Flow 12 r/min 12 r/min 7 68 Max. Flow Min. Flow 68 66 12 r/min Min. Flow 66 64 64 62 62 6 5 1 15 2 25 3 6 (7) (15) (22) (29) (36) (44) 5 Outlet 1Pressure 15 2( 25 3 Sound (7) pressure (15) data(22) (29) (36) (44) equivalent Outlet to NFPA Pressure ( Sound pressure data equivalent Typical Noise to NFPA Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) Typical and Noise 1. Levels absolute at 15 ( psi and gauge) 1 Inlet r/min 76 with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 15 r/min 76 74 Max. Flow 74 72 15 r/min Max. Flow 72 7 7 68 68 66 66 64 64 62 62 6 6 58 1 r/min Max. Flow 1 r/min Max. Flow 15 r/min Min. Flow 15 r/min Min. Flow 1 r/min Min. Flow 1 r/min Min. Flow 58 56 5 1 15 2 25 3 56 (7) (15) (22) (29) (36) (44) 5 Outlet 1 Pressure 15 2( 25 3 (7) (15) (22) (29) (36) (44) Delivery and Efficiency at 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency at 18 r/min Volumetric 9 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Efficiency 8 Volumetric 9 Efficiency 7 8 6 7 24 (63) 5 2 (53) 6 24 (63) 4 16 (42) 5 2 (53) 3 12 (32) 4 16 (42) 2 8 (21) 3 12 (32) 1 2 4 (11) 8 (21) 1 5 1 15 2 25 3 35 (7) (15)(22) (29)(36) (44)(5) 4 (11) 5 1 15 2 25 3 35 (7) (15)(22) (29)(36) (44)(5) Torque and Power at 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 72 (6372) 66 (5841) Torque and Power at 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 6 (531) 72 (6372) 54 (4779) 66 (5841) Torque 48 (4248) 6 (531) Torque 42 (3717) 54 (4779) 14 (188) 36 (3186) 48 (4248) 12 (161) 3 (2655) 42 (3717) Power, 1 (134) 14 (188) 24 (2124) 36 (3186) 8 (17) 12 (161) 18 (1593) 3 (2655) Power, 1 (134) 6 (81) 24 (2124) Torque, 12 (162) Cut-off 4 (54) 8 (17) 6 (531) 18 (1593) 2 (27) 6 (81) Torque, 12 (162) Cut-off 4 (54) 5 1 15 2 25 3 6 (531) (7) (15) (22) (29) (36) (44)(5) 35 2 (27) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44)(5) 35 Efficiency % Efficiency % Power kw (hp) Power kw (hp) 66 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Performance Industrial PVM131 Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency at 15 r/min 5 C Volumetric (12 F) and 1. absolute ( psi gauge) Inlet 9 1Efficiency Volumetric 8 9 Efficiency 78 67 24 (63) Efficiency % Efficiency % 56 45 34 23 12 2 24 (53) (63) 16 2 (42) (53) 12 16 (32) (42) 8 12 (21) (32) 4 8 (11) (21) 1 5 1 15 2 25 3 35 4 (11) (7) (15) (22)(29) (36) (44)(5) 5 Outlet 1 Pressure 15 2 ( 25 3 35 (7) (15) (22)(29) (36) (44)(5) Delivery Delivery l/min l/min (USgpm) (USgpm) Efficiency % Delivery Delivery and Efficiency and Efficiency at 12 at 12 r/min r/min 5 C 5 C (12 F) (12 F) and 1. and 1. absolute absolute ( psi ( gauge) psi gauge) Inlet Inlet 1 1 Volumetric Volumetric 9 Efficiency 9 Efficiency 8 7 6 5 4 3 2 1 Efficiency % 8 7 6 24 (63) 24 (63) 5 4 3 2 1 2 (53) 2 (53) Delivery Delivery (effective (effective flow) flow) 16 (42) 16 (42) 12 (32) 12 (32) 8 (21) 8 (21) 4 (11) 4 (11) 5 1 15 2 25 3 (7) (15) (22) (29) 35 5 1 15 2 25 3 (7) (15) (22) (29) (36)(44)(5) 35 Outlet Outlet Pressure Pressure ( ( Torque and Power at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 72 (6372) Torque and Power at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 66 72 (5841) (6372) 6 66 (531) (5841) Torque 54 6 (4779) (531) 48 (4248) Torque 54 (4779) 42 48 (3717) (4248) 36 12 (161) 42 (3186) (3717) 3 (2655) 1 (134) 36 (3186) 12 (161) 24 (2124) 8 (17) 3 (2655) 1 (134) Power, 18 24 (1593) (2124) 6 8 (81) (17) 12 (162) Power, 4 (54) 18 (1593) 6 (81) 6 (531) 2 (27) 12 (162) 4 (54) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44)(5) 35 6 (531) 2 (27) 5 Outlet 1 Pressure 15 2 ( 25 3 (7) (15) (22) (29) (36) (44)(5) 35 Power Power kw (hp) kw (hp) Torque Torque and Power and Power at 12 at 12 r/min r/min 5 C 5 C (12 F) (12 F) and 1. and 1. absolute absolute ( psi ( gauge) psi gauge) Inlet Inlet 66 (5841) 66 (5841) 6 (531) 6 (531) 54 (4779) 54 (4779) 48 (4248) 48 (4248) 42 (3717) 42 (3717) 36 (3186) 36 (3186) 3 (2655) 3 (2655) 24 (2124) 24 (2124) Torque Torque Power, Power, 1 (134) 1 (134) Full Stroke 8 (17) 8 (17) 18 (1593) 18 (1593) 6 (81) 6 (81) 12 (162) 12 (162) 4 (54) 4 (54) 6 (531) 6 (531) 2 (27) 2 (27) 5 1 15 2 25 3 (7) (15) (22) (29) (36) 35 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44)(5) 35 Outlet Outlet Pressure Pressure ( ( Power kw (hp) Power kw (hp) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 67

Performance Industrial PVM131 Delivery and Efficiency at 1 r/min Delivery and Efficiency at 1 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 1 Volumetric 9 Efficiency Volumetric 9 Efficiency 8 8 7 7 Efficiency % Efficiency % 6 6 5 5 4 4 3 3 2 2 1 1 5 1 15 2 25 3 35 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (44) 3 (5) 35 (7) Outlet (15) Pressure (22) (29) (36) ( (44)(5) 2 (53) 2 (53) 16 (42) 16 (42) 12 (32) 12 (32) 8 (21) 8 (21) 4 (11) 4 (11) Delivery Delivery l/min l/min (USgpm) (USgpm) Case Case Flow Flow l/min l/min (USgpm) (USgpm) Case Flow Versus Outlet Pressure at Full Flow, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet Case 8 (2.1) Flow Versus Outlet Pressure at Full Flow, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 8 (2.1) 7 (1.8) 7 (1.8) 6 (1.6) 6 (1.6) 5 (1.3) 5 (1.3) 4 (1.1) 4 (1.1) 3 (.8) 3 (.8) 2 (.5) 2 (.5) 1 (.3) 1 (.3) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44)(5) 5 Outlet 1 Pressure 15 2 25 ( 3 35 (7) (15) (22) (29) (36) (44)(5) Torque and Power at 1 r/min Torque and Power at 1 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 66 (5841) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 66 (5841) 6 (531) 6 (531) Torque 54 (4779) Torque 54 (4779) 48 (4248) 48 (4248) 42 (3717) 42 (3717) 36 (3186) 36 (3186) 3 (2655) 1 (134) 3 (2655) 1 (134) 24 (2124) Power, 8 (17) 24 (2124) Full Stroke Power, 8 (17) 18 (1593) 6 (81) 18 (1593) 6 (81) 12 (162) 4 (54) 12 (162) 4 (54) 6 (531) 2 (27) 6 (531) 2 (27) 5 1 15 2 25 3 35 (7) 5(15) 1(22) 15(29) 2(36) 25 (44) 3 (5) 35 (7) (15) (22) (29) (36) (44) (5) Power Power kw kw (hp) (hp) Case Case Flow Flow l/min l/min (USgpm) (USgpm) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 24 (6.3) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 24 (6.3) 2 (5.3) 2 (5.3) 16 (4.2) 16 (4.2) 12 (3.2) 12 (3.2) 8 (2.1) 8 (2.1) 4 (1.1) 4 (1.1) 5 1 15 2 25 3 35 (7) (15)(22) (29) (36) (44) (5) 5 Outlet 1 Pressure 15 2 25 ( 3 35 (7) (15)(22) (29) (36) (44) (5) 68 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Overall Efficiency (%) (%) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Performance Mobile PVM131 Noise Noise Level Level dba dba Typical Noise Levels at 2 and 6 r/min Typical with petroleum Noise Levels oil (1 at W) 2 @ and 93 C 6 (2 F) r/min with and petroleum 1. absolute oil (1 W) ( @ psi 93 C gauge) (2 F) inlet 84 and 1. absolute ( psi gauge) inlet 84 2 r/min 82 Max. flow 2 r/min 82 8 Max. flow 8 78 78 76 76 74 74 72 72 7 7 68 68 66 66 64 64 62 62 6 2 r/min Min. flow 2 r/min Min. flow 6 r/min Min. flow 6 r/min Min. flow 6 r/min Max. flow 6 r/min Max. flow 6 58 5 1 15 2 25 3 58 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (44) 3 (7) Outlet (15) Pressure (22) (29) ( (36) (44) Sound pressure Outlet data Pressure ( Sound equivalent pressure to NFPA data equivalent to NFPA Versus Speed @ Overall 93 C (2 F) Efficiency and Versus 1. Speed absolute @ 93 C (2 F) ( psi and gauge) 1. inlet absolute 95 ( psi gauge) inlet 95 9 1 9 (15 1 85 (15 5 (7 (22 85 15 5 (7 (22 8 2 8 (29 2 (29 75 25 (36 75 25 (36 28 7 (4 28 7 (4 32 (46 65 32 (46 5 1 15 2 25 65 Speed r/min 5 1 15 2 25 Speed r/min Delivery and Case Flow Versus Speed @ 93 C (2 F), full flow and 1. absolute ( gauge Inlet 26 (69) Delivery and Case Flow Versus Speed 24 (63) @ 93 C 5 (2 F), (7, full flow and 1. absolute Delivery ( gauge Inlet 22 (58) 26 (69) 2 (53) 24 (63) 5 (7, 18 (48) Delivery 28 (4, 22 (58) Delivery 16 (42) 2 (53) 14 (37) 18 (48) 28 (4, Delivery 12 (32) 16 (42) 1 (26) 2 (5.3) 14 (37) 28 (4, 8 (21) 16 (4.2) 12 (32) Case flow 6 (16) 12 1 (26) 2 (3.2) (5.3) 4 (11) 28 (4, 6 (2.1) 8 (21) 16 (4.2) Case flow 2 (5) 5 (7, Case flow 4 (1.1) 6 (16) 12 (3.2) 4 (11) 5 1 15 2 25 6 (2.1) 2 (5) 5 Speed (7 r/min, Case flow 4 (1.1) Torque Versus Speed 5 1 15 2 25 @ 93 C (2 F), Speed full r/min flow and 1. absolute ( psi gauge) inlet 8 (78) Torque Versus Speed @ 93 C (2 F), full flow and 7 (6195) 1. absolute ( psi gauge) inlet 8 (78) 32 (46 6 (531) 7 (6195) 28 (4 5 (4425) 25 32 (36 (46 6 (531) 4 (354) 2 28 (29 (4 5 (4425) 25 (36 3 (2655) 15 (22 4 (354) 2 (29 2 (177) 1 (15 3 (2655) 15 (22 1 (885) 5 (7 2 (177) 1 (15 17 (25 1 (885) 5 1 15 2 5 25 (7 Speed r/min 17 (25 5 1 15 2 25 Speed r/min EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 69

Power Power kw kw (hp) (hp) Case Case Flow Flow (l/min (l/min (USgpm) (USgpm) Performance Mobile PVM131 Torque Torque Nm Nm (in.lb.) (in.lb.) Power Versus Speed @93 C Power (2 F), Versus full flow Speed and 1. @93 C absolute (2 F), ( psi full gauge) flow and inlet 14 (188) 1. absolute ( psi gauge) inlet 32 (46 14 13 (188) (174) 32 (46 13 12 (174) (161) 28 (4 12 11 (161) 28 (4 (148) 25 (36 1 11 (148) (134) 25 (36 1 9 (134) (121) 2 (29 9 8 (121) (17) 2 (29 8 7 (17) (94) 15 (22 7 6 (94) (8) 15 (22 6 5 (8) (67) 1 (15 5 4 (67) (54) 1 (15 4 3 (54) (4) 5 (7 3 2 (4) (27) 5 (7 2 1 (27) (13) 17 (25 1 (13) 17 (25 5 1 15 2 25 5 1 Speed r/min 15 2 25 Speed r/min Torque and Case Flow Versus Speed @ Torque 93 C (2 F), and Case load Flow sense Versus standby Speed and @ 93 C 1. (2 F), absolute load ( sense psi gauge) standby inlet 18 (159) and 1. absolute ( psi gauge) inlet 18 (159) 2 (3 16 (142) differential, 2 (3 16 (142) differential, Torque 14 (124) Torque 14 (124) 12 (16) 11 (16 12 (16) differential, 11 (16 1 (88) differential, Torque 1 (88) Torque 8 (71) 7 (1.85) 8 (71) 7 (1.85) 6 (53) 2 (3 differential 6 (1.58) 6 (53) Case 2 Flow (3 differential 6 (1.58) 4 (35) Case Flow 5 (1.32) 4 (35) 5 (1.32) 2 (18) 11 (16 differential 4 (1.6) 2 (18) 11 Case Flow (16 differential 4 (1.6) Case Flow 3 (.79) 5 1 15 2 253 (.79) 5 1 Speed r/min 15 2 25 Speed r/min Case Flow l/min (USgpm) 26 (231) 24 (2124) 22 (1947) 2 (177) 18 (1593) 16 (1416) Torque and Case Flow Versus Speed @ 93 C (2 F), cut-off and 1. absolute ( psi gauge) inlet 28 (4 Torque 14 (1239) 56 (14.8) 12 (162) 48 (12.7) 15 (22 1 (885) Torque 4 (1.6) 8 (78) 6 (531) 28 (4, Case Flow 32 (8.5) 24 (6.3) 4 (354) 16 (4.2) 2 (177) 15 (22, Case Flow 8 (2.1) 5 1 15 Speed r/min 2 25 Case Flow l/min (USgpm) Case Flow at 2 r/min, Full Flow 93 C (2 F), 1. absolute ( psi gauge) Inlet 18 (4.7) 16 (4.2) 14 (3.7) 12 (3.2) 1 (2.6) 8 (2.1) 6 (1.6) 4 (1.) 2 (.5) 5 1 15 2 25 3 35 (7) (15) (22) (29)(36) (44)(5) Case Flow at 2 r/min, Minimum Flow 93 C (2 F), 1. absolute ( psi gauge) Inlet 28 (7.4) 24 (6.3) 2 (5.3) 16 (4.2) 12 (3.2) 8 (2.1) 4 (1.) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Case Flow l/min (USgpm) 7 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Performance Industrial PVM141 Noise Level Level dba dba Typical Noise Levels at 18 and 12 r/min Typical with Petroleum Noise Levels Oil (1W) at 18 at and 5 C 12 (12 F) r/min with and Petroleum 1. absolute Oil (1W) ( psi at gauge) 5 C (12 F) Inlet 84 and 1. absolute ( psi gauge) Inlet 84 82 18 r/min 82 max. 18 flow r/min 8 max. flow 8 78 78 76 76 74 12 r/min 74 12 max. flow r/min 72 max. flow 72 18 r/min 7 min. 18 flow r/min 7 min. flow 68 68 66 66 64 12 r/min 64 min. 12 flow r/min 62 min. flow 62 6 6 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) Delivery and Efficiency at 18 r/min, 5ϒC (12ϒF), and 1. absolute ( psi gauge) Inlet Delivery 1 and Efficiency at 18 r/min, 5ϒC (12ϒF), and 1. absolute ( psi gauge) Inlet Volumetric Efficiency 1 9 Volumetric Efficiency 9 8 8 7 Efficiency Efficiency % % 7 6 6 5 5 4 4 3 3 2 2 1 1 5 1 15 2 (7) (15) (22) (29) 5 1 15 2 (7) Outlet (15) Pressure (22) (29) ( 3 (79) 3 25 (79) (66) 25 2 (66) (53) 2 15 (53) (4) 15 1 (4) (26) 1 5 (13) (26) 5 (13) 25 (36) 25 (36) Delivery Delivery l/min l/min (USgpm) (USgpm) Noise Level Level dba dba Typical Noise Levels 15 and 1 r/min Typical with Petroleum Noise Levels Oil (1W) 15 at and 5 C 1 (12 F) r/min with and Petroleum 1. absolute Oil (1W) ( psi at gauge) 5 C (12 F) Inlet 78 and 1. absolute ( psi gauge) Inlet 78 76 76 15 r/min 74 max. 15 flow r/min 74 max. flow 72 1 r/min 72 7 max. 1 flow r/min 7 max. flow 68 68 15 r/min 66 min. 15 flow r/min 66 min. flow 64 64 1 r/min 62 min. 1 flow r/min 62 6 min. flow 6 58 58 56 56 54 54 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) Sound pressure Outlet data Pressure ( equivalent Sound pressure to NFPA. data equivalent to NFPA. Torque Torque Nm (in.lb.) Nm (in.lb.) Torque and Power at 18 r/min, 5ϒC (12ϒF), and 1. absolute ( psi gauge) Inlet Torque and Power at 18 r/min, 5ϒC (12ϒF), 6 (531) and 1. absolute ( psi gauge) Inlet 6 55 (531) (4867) 55 5 (4867) (4425) 5 45 (4425) (3982) Torque, 45 4 (3982) (354) Torque, 4 35 (354) (397) 35 3 (397) (2655) 15 (21) 3 25 (2655) (2212) Power, 15 125 (21) (168) 25 2 (2212) (177) Power, 125 1 (168) (134) 15 (1327) 2 (177) 1 75 (11) (134) 15 1 (1327) (885) Torque, 75 5 (11) (67) 5 (442) Cut-off 1 (885) Torque, 5 25 (67) (34) 5 (442) Cut-off 25 (34) 5 1 15 2 25 (7) (15) (22) (29) (36) 5 1 15 2 25 (7) Outlet (15) Pressure (22) (29) ( (36) Power Power kw (hp) kw (hp) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 71

Performance Industrial PVM141 Delivery and Efficiency at 15 r/min, 5ϒC (12ϒF), and 1. absolute ( psi gauge) Inlet Delivery 1 and Efficiency at 15 r/min, 5ϒC (12ϒF), and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Volumetric Efficiency 9 8 87 Efficiency % Efficiency % 76 65 54 43 32 21 3 (79) 3 25 (79) (66) 25 2 (66) (53) 2 15 (53) (4) 15 1 (4) (26) 1 5 (26) (13) 1 5 (13) 5 1 15 2 25 (7) (15) (22) (29) (36) 5Outlet 1 Pressure 15 2 ( 25 (7) (15) (22) (29) (36) Delivery and Efficiency at 12 r/min, 5 C (12 F), Delivery and and 1. Efficiency absolute at 12 ( psi r/min, gauge) 5 C Inlet (12 F), and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency 9 Volumetric Efficiency 9 8 8 7 7 6 3 (79) 6 3 (79) 5 25 (66) 5 25 (66) 4 2 (53) 4 2 (53) 3 15 (4) 3 15 (4) 2 1 (26) 2 1 (26) 1 5 (13) 1 5 (13) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) (29) ( (36) Efficiency Efficiency % % Delivery Delivery l/min l/min (USgpm) (USgpm) Deliv Deliv Efficiency Efficiency % % 1 1 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 ) ) ) Torque and Power at 15 r/min, 5ϒC (12ϒF), and 1. absolute ( psi gauge) Inlet Torque and Power at 15 r/min, 5ϒC (12ϒF), 6 (531) and 1. absolute ( psi gauge) Inlet 6 55 (531) (4867) 55 (4867) (4425) 5 45 (4425) (3982) 45 4 (3982) (354) 4 35 (354) (397) 35 3 (397) (2655) 3 25 (2655) (2212) 25 2 (2212) (177) 2 15 (177) (1327) 151 (1327) (885) 15 (885) (442) Torque, Torque, Power, Power, Power kw (hp) Power kw (hp) 15 (21) 15 125 (21) (168) 125 1 (168) (134) 1 75 (134) (11) 75 (11) (67) 525 (67) (34) 5 (442) 25 (34) 5 1 15 2 25 (7) (15) (22) (29) (36) 5 1 15 2 25 (7) Outlet (15) Pressure (22) (29) ((36) Torque Torque Nm Nm (in.lb.) (in.lb.) Torque and Power at 12 r/min, 5 C (12 F), Torque and 1. and Power absolute at 12 ( psi r/min, gauge) 5 C Inlet (12 F), and 1. absolute ( psi gauge) Inlet 6 (531) 6 55 (531) (4867) 55 5 (4867) (4425) 5 45 (4425) (3982) 45 4 (3982) (354) Torque, 4 35 (354) Torque, (397) 35 3 (397) (2655) 15 (21) 3 25 (2655) (2212) 15 (21) 125 (168) 25 2 (2212) (177) 125 (168) 1 (134) 2 15 (177) (1327) Power, 1 75 (11) (134) 15 1 (1327) Power, (885) 75 (11) 5 (67) 1 5 (885) (442) 5 (67) 25 (34) 5 (442) 25 (34) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) (29) ( (36) Power Power kw kw (hp) (hp) Torque Torque Nm Nm (in.lb.) (in.lb.) Inp Inp 6 6 55 55 5 5 45 45 4 4 35 35 3 3 25 25 2 2 15 15 1 1 72 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Performance Industrial PVM141 9) ) 6) ) 3) ) ) ) 6) ) ) Delivery Delivery l/min l/min (USgpm) (USgpm) Delivery and Efficiency at 1 r/min, 5 C (12 F), Delivery and and 1. Efficiency absolute at 1 ( psi r/min, gauge) 5 C Inlet (12 F), and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency 9 Volumetric Efficiency 9 8 8 7 7 6 3 (79) 6 3 (79) 5 25 (66) 5 25 (66) 4 2 (53) 4 2 (53) 3 15 (4) 3 15 (4) 2 1 (26) 2 1 (26) 1 5 (13) 1 5 (13) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Efficiency Efficiency % % Delivery Delivery l/min l/min (USgpm) (USgpm) Case Flow - l/min (USgpm) Case Flow Versus Outlet Pressure at Full Flow, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 7,6 (2.) 6,6 (1.75) 5,7 (1.5) 4,7 (1.25) 3,8 (1.) 2,8 (.75) 1,9 (.5),9 (.25) 5 1 15 2 25 3 35 (7) (15)(22) (29) (36) (44)(5) Outlet Pressure - ( Power Power kw kw (hp) (hp) F), F), (21) (21) (168) (168) (134) (134) (11) 1) (67) 7) (34) 4) Torque Torque Nm Nm (in.lb.) (in.lb.) Torque and Power at 1 r/min, 5 C (12 F), Torque and 1. and Power absolute at 1 ( psi r/min, gauge) 5 C Inlet (12 F), and 1. absolute ( psi gauge) Inlet 6 (531) 6 (531) 55 (4867) 55 (4867) 5 (4425) 5 (4425) 45 (3982) Torque, 45 (3982) 4 (354) Torque, 4 (354) 35 (397) 35 (397) 3 (2655) 15 (21) 3 (2655) 15 (21) 25 (2212) 125 (168) 25 (2212) 125 (168) 2 (177) 1 (134) 2 (177) 1 (134) 15 (1327) Power, 75 (11) 15 (1327) Power, 75 (11) 1 (885) 5 (67) 1 (885) 5 (67) 5 (442) 25 (34) 5 (442) 25 (34) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Power Power kw kw (hp) (hp) Case Flow - l/min (USgpm) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 22,7 (6) 18,9 (5) 15,1 (4) 11,4 (3) 7,6 (2) 3.8 (1) 5 1 15 2 25 3 35 (7) (15)(22) (29) (36) (44)(5) Outlet Pressure - ( EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 73

(%) (%) (%) Performance Mobile PVM141 Noise Level dba Noise Level dba Typical Noise Levels at at 2 and and 1 r/min with Petroleum Oil Oil (1W) at at 93 C (2 F), Typical and Noise and Levels at 2 and 1 r/min 1. 1. absolute ( ( psi psi gauge) with Inlet Petroleum Oil (1W) at 93 C (2 F), and 88 88 1. absolute ( psi gauge) Inlet 88 86 86 86 84 84 2 r/min min. min. flow flow 84 2 r/min 82 82 min. flow 82 8 8 8 78 78 2 r/min max. flow flow 78 2 r/min max. flow 76 76 76 74 74 1 r/min min. min. flow flow 74 1 r/min 72 72 min. flow 72 7 7 7 68 1 r/min 68 max. flow flow 1 r/min 68 66 66 max. flow 66 64 64 5 5 1 1 15 15 64 2 2 25 25 (7) (15) (22) (29) 5 (36) 1 15 2 25 Outlet Pressure ( ( (7) (15) (22) (29) (36) Sound pressure data data equivalent to to NFPA. Sound pressure data equivalent to NFPA. Noise Level dba versus Speed at at 93 C (2 F), Delivery and and Case Flow versus Speed at at and and 1. 1. absolute ( ( psi psi gauge) Overall Inlet Efficiency versus Speed 93 C at 93 C (2 F), (2 F), Full Full Flow and and 1. 1. absolute Delivery and Case Flow ver and 1. absolute ( psi gauge) Inlet( ( psi psi gauge) Inlet 93 C (2 F), Full Flow and 1 1 1 28 28 (74) (74) ( psi gauge) Inl 1 28 (74) 95 26 (69) 95 26 (69) 95 26 (69) 24 24 (63) (63) 91 1 (15 1 1 9 24 (63) 9 1 (15 1 15 22 22 (58) (58) (15 15 (22 85 22 (58) (15 85 Delivery 15 (22 85 5 2 (53) 5 2 (53) Delivery 5 2 (53) 8 21 21 8 21 (3 21 (3 8 21 (3 (7 18 18 (48) (48) 2 23 (7 18 Delivery 23 (33 (48) 75 16 (42) p 75 16 (42) 23 (33 Case 75 14 (37) 16 (42) 14 (37) Flow 7 14 (37) l/min 7 7 12 12 (32) (32) (USgpm) 65 65 21 12 (32) 1 (26) 21 (3 1 (26) 1 1 (2.6) 65 Case 21 ( 1 Flow (26) 6 6 8 8 (21) (21) 8 8 (2.1) Case 6 6 6 (16) (16) 8 (21) 6 6 (1.6) 55 55 6 (16) 55 4 4 (11) (11) 4 4 (1.1) 5 5 2 (5) 4 (11) 2 (5) 2 2 (.5) 5 1 1 (15 Case Flow 2 (5) 1 (15 5 5 1 15 2 25 5 5 1 15 2 25 5 1 15 2 25 5 1 15 Speed (r/min) Speed (r/min) Speed (r/min) Speed (r/min) Delivery l/min (USgpm) 74 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Performance Mobile PVM141 Torque Torque versus Torque versus Speed versus Speed at 93 C Speed at at 93 C (2 F), 93 C (2 F), (2 F), Full Full Flow Full Flow and Flow and 1. and 1. 1. absolute absolute ( psi absolute ( ( psi gauge) psi gauge) Inlet gauge) Inlet Inlet 6 6 (531) 6 (531) (531) 55 55 (4867) 55 (4867) (4867) 23 23 23 (33 (33 (33 5 5 (4425) 5 (4425) (4425) 21 21 21 (3 (3 (3 45 45 (3982) 45 (3982) (3982) 4 4 (354) 4 (354) (354) 35 35 (2655) 35 (2655) 15 15 (2655) 15 (22 (22 (22 3 3 (2655) 3 (2655) (2655) 25 25 (2212) 25 (2212) (2212) 1 1 1 (15 (15 (15 2 2 (177) 2 (177) (177) 15 15 (1327) 15 (1327) (1327) 1 1 (885) 1 (885) (885) 5 5 5 (725 (725 (725 5 (442) 5 5 (442) 17 17 (442) 17 (25 (25 (25 5 51 5 115 1 152 15 225 2 253 25 3 3 Speed Speed (r/min) Speed (r/min) (r/min) Torque Torque Nm Nm (in.lb.) (in.lb.) Power Power versus Power versus Speed, versus Speed, 93 C Speed, 93 C (2 F), 93 C (2 F), (2 F), and and 1. and 1. 1. absolute absolute ( psi absolute ( ( psi gauge) psi gauge) Inlet gauge) Inlet Inlet 12 12 (161) 12 (161) (161) 23 23 23 11 11 (148) 11 (148) (33 (148) (33 (33 21 21 1 1 (134) 21 1 (134) (134) (3 (3 (3 9 9 (121) 9 (121) (121) 8 8 (17) 8 (17) (17) 15 15 15 (22 (22 (22 7 7 (94) 7 (94) (94) 6 6 (8) 6 (8) (8) 1 1 5 1 5 (67) 5 (67) (67) (15 (15 (15 4 4 (54) 4 (54) (54) 3 3 (4) 5 3 (4) 5 (4) 5 (7 (7 (7 2 2 (27) 2 (27) (27) 17 17 1 17 1 (13) 1 (13) (25 (13) (25 (25 Power kw (hp) Power Power kw kw (hp) (hp) 5 5 1 5 1 15 1 15 2 15 2 25 2 25 25 Speed Speed (r/min) Speed (r/min) (r/min) Torque Torque Nm Nm (in.lb.) (in.lb.) Torque Torque and Torque and Case and Case Flow Case Flow versus Flow versus Speed versus Speed at 93 C Speed at at 93 C 93 C (2 F), (2 F), Load (2 F), Load Sense Load Sense Standby Sense Standby and Standby and 1. and 1. 1. absolute absolute absolute ( psi ( ( psi gauge) psi gauge) Inlet gauge) Inlet Inlet 14 (124) 14 14 (124) (124) 13 (115) 13 13 (115) (115) 12 (16) 12 12 (16) (16) 11 (97) 11 11 (97) (97) 1 (89) 1 1 (89) (89) 9 (8) 9 9 (8) (8) 8 (71) 8 8 (71) (71) 7 (62) 7 7 (62) (62) 6 (53) 6 6 (53) (53) 5 (44) 5 5 (44) (44) 4 (35) 4 4 (35) (35) 3 (27) 3 3 (27) (27) 2 (18) 2 2 (18) (18) 1 (9) 1 1 (9) (9) 2 2 2 (29 (29 (29 diff. diff. diff. Torque Torque Torque 11 11 11 (16 (16 (16 diff. diff. diff. Torque Torque TorqueCase Case Flow Case Flow l/min Flow l/min (USgpm) l/min (USgpm) (USgpm) 6.5 6.5 (1.72) 6.5 (1.72) 2 2 (1.72) 2 (29 (29 (29 diff. diff. Case diff. Case Flow Case Flow 6. 6. (1.58) Flow 6. (1.58) (1.58) 5.5 5.5 (1.45) 5.5 (1.45) (1.45) 5. 5. (1.32) 5. (1.32) (1.32) 4.5 4.5 (1.19) 4.5 (1.19) 11 11 (1.19) 11 (16 (16 (16 4. 4. (1.6) diff. 4. (1.6) diff. Case (1.6) diff. Case Flow Case Flow Flow 3.5 3.5 (.92) 3.5 (.92) (.92) 3. 3. (.79) 3. (.79) (.79) 5 5 1 5 1 15 1 15 2 15 2 25 2 25 25 Speed Speed (r/min) Speed (r/min) (r/min) Torque Torque and Torque and Case and Case Flow Case Flow versus Flow versus Speed versus Speed Speed at 93 C at at 93 C (2 F), 93 C (2 F), Pressure (2 F), Limit Pressure Limit Cut-Off Limit Cut-Off and Cut-Off and and 1. 1. 1. absolute absolute ( psi absolute ( ( psi gauge) psi gauge) Inlet gauge) Inlet Inlet 11 11 (973) 11 (973) (973) 1 1 (885) 1 (885) (885) 9 (796) 9 9 (796) (796) 21 21 21 (3 (3 (3 8 (78) 8 8 (78) (78) Torque Torque Torque 15 15 7 15 (22 (22 7 (619) (22 7 (619) (619) Torque Torque Torque 6 (531) 6 6 (531) Case Case Flow (531) Case Flow l/min l/min Flow l/min 5 (442) 5 5 (442) (USgpm) (USgpm) (442) (USgpm) 4 (354) 4 4 (354) 2 2 (5.3) (354) 2 (5.3) (5.3) 21 21 3 21 (3 (3 (3 3 (265) 3 (265) 15 (265) Case Case Flow 15 (2.6) Case Flow Flow 15 (2.6) (2.6) 2 (177) 2 2 (177) 15 1 15 (177) 15 (22 (22 (22 1 (4.) 1 (4.) (4.) Case Case Flow 1 Case Flow 1 (88) Flow 1 (88) 5 (1.3) 5 (88) 5 (1.3) (1.3) 5 5 1 5 115 1 152 15 225 2 25 25 Speed Speed (r/min) Speed (r/min) (r/min) Torque Torque Nm Nm (in.lb.) (in.lb.) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 75

End-ported Models PVM18/2 Dimensions in millimeters (inches) Drain port F (See options on page 17.) See shaft options starting on page 12. E Alt. drain port F. (See options on page 17.) Load sense port J. (See options on page 17.) 72, (2.83) 58, (2.28) 72, (2.83) 58, (2.28) 73, (2.87) 76, (2.99) Control position for right hand (cloc kwise) shaft rotation, as viewed from shaft end. Position for left hand rotation is shown on following page. F G (with adj. max. stop) H (without adj. max. stop) Adjustable maximum displacement stop (1 turn = 1.1 cm 3 /rev). CCW reduces displacement. 37,4 (1.47) 165,7 (6.52) B M C D M 85,1 (3.35) 55,2 (2.17) A 23, (.91) J K L Inlet gauge port K. See options on page 17. Inlet port B. See options on page 16. Drain port F. See options on page 17. 34,5 (1.36) Outlet port C. See options on page 16. 34, (1.34) 76 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

End-ported Models PVM18/2 Dimensions in millimeters (inches) Dimensions in millimeters (inches) 37,4 37,4 (1.47) (1.47) Adjustable maximum displacement Adjustable stop (1 turn maximum = 1.1 cm 3 displacement /rev). CCW stop reduces (1 turn displacement. = 1.1 cm 3 /rev). CCW reduces displacement. Inlet position for right hand rotation (Position Inlet for left position hand rotation for right shown hand rotation below). (Position for left hand rotation shown below). 165,7 165,7 (6.52) (6.52) Control position for right hand Control rotation position (Load sensing for right control hand rotation shown) (Load sensing control shown) Outlet Outlet 34,5 34, (1.36) 34,5 (1.34) 34, (1.36) (1.34) Inlet/Outlet Ports and Control Positioned Inlet/Outlet for Ports Ri ght Hand Control Rotation Positioned for Ri ght Hand Rotation Control position for left hand Control rotation position (Pressure for compensated left hand rotation control shown) (Pressure compensated control shown) 37,5 (1.48) 37,5 (1.48) 14,5 14,5 (5.53) (5.53) 126,3 126,3 (4.97) (4.97) Outlet Outlet Inlet position for left hand Inlet rotation position (Position for left for hand right rotation hand rotation (Position shown for right above) hand rotation shown above) Inlet/Outlet Ports and Control Positioned Inlet/Outlet for Ports Left Hand Rotation Control Positioned for Left Hand Rotation EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 77

Side-ported Models PVM18/2 Dimensions in millimeters (inches) Load sense port J (See options on page 17) Alt. drain port F (See options on page 17) Drain port F (See options on page 17) E M C L outlet port C. Outlet port C. See options on page 16. See shaft options starting on page 12. 72, (2.83) 72, (2.83) 58, (2.28) Control position for right hand (clockwise) shaft rotation, as viewed from shaft end. Position for left hand rotation is shown on following page. F G (with adj. max. stop) H (without adj. max. stop) To pilot mtg. flg. M N Adjustable maximum displacement stop (1 turn = 1.1 cm 3 /rev). CCW reduces displacement. Outlet port C (above). See options on page 16. Inlet port B. See options on page 16. 114,7 (4.52) B A M C D M 18,8 (4.28) 85,1 (3.35) 55,2 (2.17) 23, (.91) Alt. drain port F. See options on page 17. J L K Inlet gauge port K. See options on page 17. 21,9 (.86) 62,9 (2.48) 21,6 (.85) 62,9 (2.48) Outlet gauge port K. See options on page 17. 78 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Side-ported Models PVM18/2 Dimensions in in millimeters (inches) Adjustable maximum displacement stop stop (1 (1 turn turn = = 1.1 1.1 cm cm 3 /rev). 3 CCW reduces displacement. 114,7 (4.52) Control position for for right right hand rotation (Load sensing control shown) Inlet Inlet position for for right right hand r otation r (Position for for left left hand rotation shown below) Outlet gauge port port K. K. See See options on on page 17. 17. Inlet Inlet gauge port port K. K. See See options on on page 17. 17. Outlet 21,9 21,9 (.86) (.86) 62,9 62,9 (2.48) 21,6 21,6 (.85) (.85) 62,9 62,9 (2.48) Inlet/Outlet Ports and and Control Positioned for for Ri Ri ght ght Hand Rotation Control position for for left left hand r otation r (Pressure compensated control shown) 86,5 86,5 (3.41) 72,3 72,3 (2.85) Outlet gauge port port K. K. See See options on on page 17. 17. Inlet Inlet gauge port port K. K. Seep options on on page 17. 17. Outlet Inlet Inlet position for for left left hand rotation (Position for for right right hand rotation shown above) Inlet/Outlet Ports and and Control Positioned for for Left Left Hand Rotation EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 79

Thru-drive Models PVM18/2 Dimensions in millimeters (inches) Load sense port J (See options on page 17) Alt. drain port F (See options on page 17) Drain port F (See options on page 17) 124, (4.88) 164,2 (6.46) Centerline of outlet port Outlet port C. See options on page 16 See shaft options starting on page 17. 72, (2.83) to pilot mtg. flg. 164,2 (6.46) 72, 58, (2.83)(2.28) Control position for right hand (clockwise) shaft rotation, as viewed from shaft end. Position for left hand rotation is shown on following page. 26,1 (1.3) 221,4 (8.72) with adj. max. stop 212,3 (8.36) without adj. max. stop Adjustable maximum displacement stop (1 turn = 1.1 cm 3 /rev). CCW reduces displacement. Inlet port B. See options on page 16. 114,7 (4.52) A B 85,1 (3.35) 18,1 (4.14) 23, (.91) 6, (2.36) C M D M 99, (3.9) 167,7 (6.6) 223,2 (8.79) 62,9 (2.48) 64,2 (2.53) Alt. drain port F. See options on page 17. 8 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Thru-drive Models PVM18/2 Model Code Position 25 Description A For SAE A pad with a 9T, 16/32 DP, 3 pressure angle, involute spline B For SAE A pad with a 11T, 16/32 DP, 3 pressure angle, involute spline G For ISO 8 A2HW pad with a 9T SAE spline H For ISO 8 A2HW pad with a 11T SAE spline Dimensions in millimeters (inches) Adjustable maximum displacement stop (1 turn = 1.1 cm 3 /rev). CCW reduces displacement. Inlet position for right hand rotation (Position for left hand rotation shown below) 114,7 (4.52) Outlet Control position for right hand rotation (Load sensing control shown) Inlet/Outlet Ports and Control Positioned for Right Hand Rotation 62,9 (2.48) 64,2 (2.53) Control position for left hand rotation (Pressure compensator control shown) Output shaft 21T, 32/64 DP, 3 PA involute spline. 57,49 (2.26) 86,5 (3.41) 72,3 (2.85) 4,46 (1.59) 12,25 (.48) 27, (1.6) 79,4 (3.13) K (2 places) 53,5 (2.11) 159,2 (6.27) G 89,7 (3.531) 89,6 (3.527) 2, (.79) 1,9 (.75) Outlet H H Inlet position for left hand rotation (Position for right hand rotation shown above) Inlet/Outlet Ports and Control Positioned for Left Hand Rotation 8,5 (.33) N (2 places) 2, (.79) 2, (.79) Model Code Position 25 ØG H K N A,B 82,625 (3.253) 82,575 (3.251) 53,2 (2.9) 375-16 UNC-2B thd..75 deep min 375-16 UNC-2B thd..62 deep min. G,H 8,46 (3.151) M1 x 1,5 thd. M1 x 1,5 thd. 8,2 (3.15) 54,5 (2.15) 19,5 deep min 15,88 deep min. EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 81

Flange Designations PVM18/2 A Pilot Flange Designation ØA B C D E F G H J K L M SAE J744-82-2 82,55 11,35/1,97 16,4 53,2 Model Code A (3.25) (.447/.432) (4.19) (2.9) 131,5 33,6 228,9 219,8 16,5 166,7 2,7 65,2 ISO 319/2-8A2HW 8, 11,27/11, 19, 54,5 (5.18) (1.32) (9.) (8.65) (4.19) (6.56) (7.9) (2.57) Model Code B (3.15) (.444/.433) (4.29) (2.15) B Pilot Flange Designation SAE J744-11-2 11,6 14,55/14,17 146, 73, Model Code C (4.) (.572/.557) (5.75) (2.875) 124, 26,1 221,4 212,3 99, 159,2 193,9 87, ISO 319/2-1A2HW 1, 14,27/14, 14, 7, (4.88) (1.3) (8.72) (8.36) (3.9) (6.27) (7.63) (3.43) Model Code D (3.937) (.562/.551) (5.512) (2.756) Pilot Flange Designation ØA B C D SAE J744-127-2 Model Code C 11,6 (4.) 14,55/14,17 (.572/.558) 146, (5.75) 73, (2.87) ISO 319/2-1 A2HW Model Code D 1, (3.94) 14,27/14, (.562/.551) 14, (5.51) 7, (2.76) 82 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

End-ported Models PVM45/5 Dimensions in millimeters (inches) See shaft options starting on page 12. Drain port F. See options on page 17. Alternate drain port F Inlet gauge port K 8, (3.15) 28, (1.1) 8, (3.2) 8, (3.15) 8, (3.2) Adjustable maximum displacement stop (1 turn = 2 cm 3 /rev). 44,6 (1.75) Alternate load sense port J 36,9 (1.45) Control position for left hand (countercloc kwise) shaft rotation, as viewed from shaft end. Position for right hand rotation is shown on following page. B 257, (1.12) max. 247, (9.72) 178,6 (7.3) 19,1 (.75) 134,3 (5.29) max. Load sensing control (See pressure compensated control on following page.) Load sense port J. See options on page 17. Inlet port B. See options on page 16. E 13,6 (5.14) 42, (1.65) C D 87, (3.425) 174, (6.85) A 135,4 (5.33) 47,8 (1.88) 175, (6.89) Alternate 75,1 212, (8.35) (2.96) drain port F Outlet gauge port K. See options on page 17. 87,1 (3.43) Outlet port C. See options on page 16. 53, (2.9) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 83

End-ported Models PVM45/5 Dimensions in millimeters (inches) Dimensions in millimeters (inches) 34,4 (1.35) 34,4 98,9 (1.35) (3.89) 98,9 (3.89) Control position for left hand rotation Control position for Non-maximum left hand adjustment rotation stop control cap. See preceding Non-maximum page adjustment for adjustable maximum stop control displacement cap. See stop preceding page for adjustable Inlet position maximum for displacement right hand stop Outlet rotation (Position for left hand Inlet position rotation for shown right below) hand Outlet rotation (Position for left hand rotation shown below) 53, 47,8 (1.88) (2.9) 87,1 75,1 53, (3.43) (2.96) 47,8 (1.88) (2.9) 87,1 75,1 Inlet/Outlet Ports (3.43) and Control (2.96) Positioned for Ri gh t Hand Rotation Inlet/Outlet Ports and Control Positioned for Ri gh t Hand Rotation 121,8 (4.8) max. 121,8 (4.8) max. 4, (.16) Control position for right hand rotation (Pressure compensated 4, (.16) control Control shown) position for right hand rotation (Pressure compensated control shown) 138,5 (5.45) 138,5 (5.45) Control position for left hand rotation (Load sensing Control position control shown) for left hand rotation (Load sensing control shown) Control position for right hand rotation Control position for right hand rotation Inlet position for left hand Outlet rotation (Position for right hand Inlet position rotation for shown left hand above) Outlet rotation (Position for right Inlet/Outlet Ports and Control Positioned hand rotation shown above) for Left Hand Rotation Inlet/Outlet Dimensions Ports shown and on Control preceding Positioned page. for Left Hand Rotation Dimensions shown on preceding page. 84 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Side-ported Models PVM45/5 Dimensions in millimeters (inches) 81,3 (3.2) Adjustable max. displacement stop (1 turn = 2 cm 3 /rev) Drain port F. See options on page 17. 36,9 (1.45) See shaft options starting on page 12. Inlet gauge port K Outlet gauge port K. See option on page 17. 81,3 (3.2) 134.3 (5.29) max. 57,5 (2.26) 5, (1.97) 72,5 (2.85) 69, (2.72) View Z-Z 257, (1.12) max. 168,2 (6.62) 75,5 (2.97) Load sensing control (See pressure compensated control on following page.) Alternate load sense port J 247, (9.72) 178,6 (7.3) 72,1 (2.84) 19,1 (4.3) 44,6 (1.75) 13,6 (5.14) Load sense port J. See options on page 17. 117,6 (4.63) E Control position for right hand (cloc kwise) shaft rotation, as viewed from shaft end. Position for left hand rotation is shown on following page. 19,1 (.75) B Z 42. (1.65) 23, (9.6) Outlet port C. See options on page 16. 183, (7.2) Alternate drain port F 78, (3.7) 28, (8.19) C D 87, (3.425) 174, (6.85) A 135,4 (5.33) 191,6 (7.54) Alternate drain port F Inlet port B. See options on page 16. Z 42. (1.65) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 85

Side-ported Models PVM45/5 Dimensions in millimeters (inches) Dimensions in millimeters (inches) 121,8 (4.8) max. 34,4 (1.35) 121,8 (4.8) max. 34,4 (1.35) Control position for left hand Control position for left hand 98,9 (3.89) 98,9 (3.89) rotation (Pressure compensated 4, (.16) Control position for right hand rotation rotation (Pressure compensated control shown). Inlet/outlet port 4, (.16) Control position for right hand rotation (Inlet/outlet port positions for right hand control shown). Inlet/outlet port (Inlet/outlet port positions for right hand positions for left hand rotation rotation are shown on preceding page.) positions for left hand rotation rotation are shown on preceding page.) are the opposite of those shown Non-maximum adjustment stop control are the opposite of those shown Non-maximum adjustment stop control for right hand rotation on 138,5 cap. See preceding page for adjustable for right hand rotation on preceding page. 138,5 cap. See preceding page for adjustable (5.45) maximum displacement stop. preceding page. (5.45) maximum displacement stop. Outlet gauge port Outlet gauge port K. See options K. See options Inlet gauge on page 17. Inlet gauge on page 17. port K port K 57,5 (2.26) 5, (1.97) 57,5 (2.26) 5, (1.97) 72,5 (2.85) 72,5 (2.85) 69, (2.72) 69, (2.72) Inlet/Outlet Ports and Control Positioned Inlet/Outlet for Ports Lef Hand and Control Rotation Positioned for Lef t Hand Rotation Control position for left hand rotation Control position for left hand rotation (Inlet/outlet port positions for left hand (Inlet/outlet port positions for left hand rotation are the opposite of those rotation are the opposite of those shown for right hand rotation on shown for right hand rotation on preceding page.) preceding page.) Inlet gauge Inlet gauge port K port K Control position for right hand rotation Control position for right hand rotation (Load sensing control shown). Inlet/outlet (Load sensing control shown). Inlet/outlet port positions for right hand rotation are port positions for right hand rotation are shown on preceding page. shown on preceding page. Outlet gauge port K. See Outlet gauge port K. See options on page 17. options on page 17. Inlet/Outlet Ports and Control Positioned Inlet/Outlet Ports and Control Positioned for Right Hand Rotation for Right Hand Rotation Dimensions shown on preceding page. Dimensions shown on preceding page. 86 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Thru-drive Models PVM45/5 Dimensions in millimeters (inches) 13,6 (5.14) 78,6 (3.9) Outlet port C. See options on page 16. 133,3 (5.25) 11,8 (4.36) View A-A C 87, (3.43) B 183, (7.2) 28, (8.19) 87, (3.43) 34,1 (1.34) 44,6 (1.76) See shaft options starting on page 12. D 81,3 (3.2) 81,3 (3.2) Load sense port J. See options on page 17. 168,2 (6.62) 117,6 (4.63) A Flange dependent 42, (1.65) Drain port F. See options on page 17. 197,7 (7.78) 135,8 (5.35) Alt. drain port F. See options on page 17. 68,8 (2.71) 72,3 (2.85) Drain port F. See options on page 17. 36,9 (1.45) 178,6 (7.3) 191,6 (7.54) 251, (9.88) 249, (9.8) 11, (.43) 138,5 (5.45) 121,8 (4.8) 98,9 (3.89) Control position for L.H. rotation Left Hand Rotation 34,4 (1.35) Control position for R.H. rotation Adjustable maximum displacement stop (1 turn = 2.1 cm 3 /rev) Load sense control position for L.H. rotation Inlet port B. See options on page 16. 5,4 (.21) 42, (1.65) Ri ght Han d Rotation Load sense control position for R.H. rotation A A Outlet gauge port K Ri ght Hand Rotation with Load Sensing Control and Tube Ports Inlet gauge port K. See options on page 17. 35, (1.38) 36, (1.42) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 87

Thru-drive Models PVM45/5 Dimensions in millimeters (inches) A Pad 61,74 (2.43) 4,4 (1.59) 12,24 (.482) G 31,75 (1.25) Output shaft 26T, 32/64 DP, 3 PA involute spline. 89,7 (3.531) 89,6 (3.527) N (2 places) H H Model Code Position 25 Description A For SAE A pad with a 9T, 16/32 DP, 3 pressure angle, involute spline B For SAE A pad with a 11T, 16/32 DP, 3 pressure angle, involute spline C For SAE B pad with a 13T, 16/32 DP, 3 pressure angle, involute spline D For SAE B pad with a 15T, 16/32 DP, 3 pressure angle, involute spline G For ISO 8-A2HW pad with a 9T SAE spline H For ISO 8-A2HW pad with a 11T SAE spline J For ISO 1-A2/B4HW pad with a 13T SAE spline B Pad 263,5 (1.37) Output shaft 26T, 32/64 DP, 3 PA involute spline. 276, (1.87) 86,49 (3.41) 1,28 (.4) 53, 53, (2.9) (2.9) K (2 places) L (4 places) J (2 places) 77,47 (3.5) 11,75 (.46) G 17,9 (4.248) 17,82 (4.244) 2, (.79) 1,9 (.75) 35,3 (1.39) 86, (3.39) 2 plcs 86, (3.39) 2 plcs H H J (2 places) K (2 places) N (2 places) M (4 places) Model Code Position 25 ØG H J K L M N A,B 82,58 (3.251) 82,52 (3.249) 53.2 (2.9).375-16 UNC-2B thd..6 deep min. G,H 8,46 (3.15) 8,2 (3.149) 54,5 (2.15) M1 thd. x 1,5 15, deep min. C,D 11,65 (4.2) 73, 44,9 89,8.5-13 UNC-2B thd..5-13 UNC-2B.5-13 UNC-2B 11,6 (4.) (2.87) (1.77) (3.54) 24.9 deep min. M12 x thd. thru M1 x thd. thru 1,5 thd. 24,9 deep min. 1,5 thd. thru M12 x 1,5 thd. thru J,K 1, (3.937) 99,946 (3.935) 7, (2.76) 44,2 (1.74) 88,38 (3.48) M12 thd. x 1,5 thd. 24,9 deep min. M1 x 1,5 thd. thru M12 x 1,5 thd. thru 88 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Flange Designations PVM45/5 Pilot Flange Designation ØA B C D E SAE J744-11-2 11,6/11,55 (4./3.998) 9,7/9,19 (.382/.362) 146, (5.75) 73, (2.875) 14,55/14,17 (.572/.557) ISO 319/2-1A2HW 1,/99,95 (3.937/3.935) 9,5/9, (.374/.354) 14, (5.512) 7, (2.756) 14,27/14, (.562/.551) Pilot Flange Designation ØA B C D SAE 2-bolt mount 11,6/11,55 (4./3.998) 73, (2.87) 146, (5.75) 14,55/14,17 (.572/.557) ISO 1 2-bolt mount 1,/99,95 (3.937/3.935) 7, (2.76) 14, (5.512) 14,27/14, (.562/.551) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 89

End-ported Models PVM57/63 Dimensions in millimeters (inches) See mounting flange options on page 11. See shaft options starting on page 12. 269,7 (1.62) w/o adj. max. stop 116, (4.57) 26,2 (8.12) 82,3 (3.24) 82,3 (3.24) Outlet port C. See options on page 16. SAE.5-13 UNC-2B thd. 1.6 deep min. ISO M12 x 1,75 thd. 29. deep min. 199,3 (7.85) 121,8 (4.8) 77,5 (3.5) 77,78 (3.6) 38,89 (1.53) 21,44 (.84) 42,88 (1.69) Left Hand Rotation, Tube Port with Pressure Compensator Inlet port B. See options on page 16. 88,7 (3.49) 254,3 (1,) 13,1 (.51) 75,7 (2.98) 165,6 (6.52) Ri gh t Hand Rotation, Flange Port with Load Sensing Control Inlet port B. See options on page 16. 52,38 (2.6) 26,19 (1.3) SAE.375-16 UNC-2B thd..88 deep min. ISO M1 x 1,5 thd. 23. deep min. 26,18 (1.3) Outlet port C. See options on page 16. 87, (3.43) Outlet gauge port K. Inlet gauge port K on opposite side. See options on page 17. 274,8 (1.82) 245,4 Drain port F. (9.66) Alternate drain port F on opposite side. See options on page 17. 168,2 (6.62) 292,2 w/adj. max. stop (11.5) Load sense port J. See options on page 17. 21,4 (7.93) 32,9 (1.3) 12,8 (4.5) 39, (1.54) 157, (6.18) 9 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Side-ported Models PVM57/63 Dimensions in millimeters (inches) See mounting flange options on page 11. See shaft options starting on page 12. 116, (4.57) 198,1 (7.8) 269,7 (1.62) w/o adj. max. stop 82,3 (3.24) Outlet gauge port K. See options on page 17. Inlet gauge port K. See options on page 17. 157, (6.18) 82,3 (3.24) Left Hand Rotation with Pressure Compensator 274,8 (1.82) 168,2 (6.62) 32,9 (1.3) Adjustable maximum displacement stop 1 turn = 2.98 l/min (.79 USgpm) Inlet port B. See options on page 16. Load sense port J. See options on page 17. 247,9 (9.76) 165,6 (6.52) Outlet port C. See options on page 16. 266,5 (1.49) 292,2 (11.5) w/adj. max. stop 213,4 (8.4) 241,5 (9.51) 224,4 (8.83) To mounting face 21,44 (.84) 42,88 (1.69) 38,89 (1.53) 77,78 (3.6) 199,3 (7.85) SAE.5-13 UNC-2B thd. 1.6 deep min. ISO M12 1,75 thd. 29. deep min. 121,8 (4.8) 77,5 (3.5) 61,5 (2.42) 75, (2.95) 75, (2.95) 57, (2.24) Ri gh t Hand Rotation with Load Sensing Control 87, (3.43) 52,37 (2.6) 26,2 (1.3) SAE.375-16 UNC-2B thd..88 deep min. ISO M1 x 1,5 thd. 23. deep min. 13,1 (.51) 26,19 (1.3) 12,8 (4.5) Drain port F. Alternate drain port F on opposite side. See options on page 17. 39, (1.54) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 91

Thru-drive Models PVM57/63 Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. 116, (4.57) 25, (8.7) 44,8 (1.76) S (See table next page) 8,1 (3.15) Alternate drain port F 82,3 (3.24) M12 thd. 21, deep (4 places) R T1 (2 places) Left Hand Rotation with Pressure Compensator and SAE 2-bolt A Flange (no adapter) SAE.5-13 UNC-2B thd. 1.6 deep min. ISO M12 x 1,75 thd. 29. deep min. Inlet port B. See options on page 16. 254,6 (1,) 165,6 (6.52) 157, (6.18) Load sense port J. See options on page 17. Outlet port C. See options on page 16. 168,2 (6.62) 292,2 (11.5) 284,4 (11.2) 213,4 (8.4) 32,9 (1.3) 82,3 (3.24) 21,44 (.84) 42,88 224,4 (1.69) (8.83) To mounting face 77,78 (3.6) 38,89 (1.53) 121,8 (4.8) 199,3 (7.85) Inlet gauge port K. See options on page 17. 77,5 (3.5) 12, (.47) 89, (3.5) 14, (.55) 92, (3.62) Outlet gauge port K. See options on page 17. Ri gh t Hand Rotation with Load Sensing Control and SAE 2-bolt A Flange (no adapter) 87, (3.43) 52,37 (2.6) 26,18 (1.3) 26,2 (1.3) 13,1 (.52) SAE.375-16 UNC-2B thd..88 deep min. ISO M1 x 1,5 thd. 23. deep min. 12,8 (4.5) 39, (1.54) Drain port F. Alternate drain port F on opposite side. See options on page 17. 92 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Thru-drive Models PVM57/63 Dimensions in millimeters (inches) 68,7 (2.7) S Coupling Length Code SAE A, 9T 62,5 (2.46) A,G SAE B, 13T 93, (3.66) C,J SAE B-B, 15T 93, (3.66) D,K SAE C, 14T 93, (3.66) E,L Coupling length (see table) B Adapter Flange To mounting face 39,9 (12.2) 35, (1.38) (4 plcs) Coupling (see table) T1 T2 Model Code Position 25 Description A SAE A, 9T, 16/32 DP, 3 pressure angle, involute spline C SAE B, 13T, 16/32 DP, 3 pressure angle, involute spline D SAE B-B, 15T, 16/32 DP, 3 pressure angle, involute spline E SAE C, 14T, 12/24 DP, 3 pressure angle, involute spline G For ISO 8-A2HW pad with a 9T SAE spline J For ISO 1-A2/B4HW pad with a 13T SAE spline K For ISO 1-A2/B4HW pad with a 15T SAE spline L For ISO 125-A2/B4HW pad with a 14T SAE spline 297,4 V Support mounting point (4 plcs) R 92, (3.62) (11.7) To mounting face Right hand rotation with Load Sensing Control and SAE 2-/4-bolt B adapter flange Support Model Code Position 25 Pilot Dia. Pilot Depth 2-bolt 4-bolt Mounting Points Flange Bolt R S T1 T2 V A,B SAE A 2-bolt SAE Ø82,65 (3.25±.1) 8,6/8,1 (.32/.34).375-16 UNC-2B thd. N/A N/A G,H ISO 8 ISO Ø8,5 (3.15) 9,/8, (.35/.31) M1 thd. N/A N/A C,D SAE B 2-/4-bolt SAE Ø11,65 (4.2±.1) 12,5/11,5 (.49/.45).5-13 UNC-2B thd..5-13 UNC-2B thd..5-13 UNC-2B thd..98 deep J,K ISO 1 ISO Ø1,5 (3.94) 12,5/11,5 (.49/.45) M12 thd. M12 thd. M12 thd. x 25, deep EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 93

Thru-drive Models PVM57/63 Dimensions in millimeters (inches) C Adapter Flange To mtg, face 297,4 (11.7) R 92, (3.62) W (4 plcs) 17, (4.21) 35, (1.38) (4 plcs) T2 39,9 (12.2) To mtg. face T1 Left hand rotation with Pressure Compensator and SAE 2-/4-bolt C Adapter Flange Support Model Code Position 25 Pilot Dia. Pilot Depth 2-bolt 4-bolt Mounting Points Flange Bolt R S T1 T2 V E,F SAE C 2-/4-bolt SAE Ø127,5 (5.2±.1) 15,5/14,5 (.61/.57).625-11 UNC-2B thd..5-13 UNC-2B thd..5-13 UNC-2B thd..98 deep L,M ISO 125 ISO Ø125,5 (4.92) 15,5/14,5 (.61/.57) M16 thd. M12 thd. M12 thd. x 25, deep 94 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Side-ported Models PVM74/81 *Right Hand Only Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. 12, (4.2) Lifting point.375-16 UNC thd. 1, (.39) deep with SAE drain M1 thd. 1, (.39) deep with ISO drain Alt. drain port "F". See options on page 17. Alt. drain port "F". See options on page 17. Outlet port "C". See options on page 16. Inlet port "B". See options on page 16. 87, (3.42) 2X Outlet gauge port "K". See options on page 17. Inlet port "B". See options on page 16. TO MOUNTING FACE 249,6 (9.83) Left hand rotation with Pressure Compensator 86, (3.39) 86, (3.39) Alt. drain port "F". See options on page 17. Inlet gauge port "K". See options on page 17. Inlet gauge port "K". See options on page 17. Max. Adj. stop. One rotation will change displacement 6,1-6,8 l/min (1.6-1.8 USgpm) at 18 rpm 65, (2.56) 92, (3.62) 114, (4.49) 4,3 (.17) 91, (3.58) 143,3 (5.64) 114, (4.49) 65, (2.56) Right hand rotation with Load Sensing Control Load sense port "J". See options on page 17. Outlet gauge port "K". See options on page 17. 11, (4.33) 16,8 (.66) Outlet port "C". See options on page 16. Drain port "F". See options on page 17. 113,6 (4.47) 319,1 w/o max adj stop (12.56) 334,8 (13.18) 279,6 (11.1) 246,6 (9.71) 288, (11.34) 194,8 ( 7.67) 146,1 ( 5.75) C/G location 181,6 (7.15) 33,9 (1.33) 33, (1.3) PVM74/18 is not available with left hand rotation in any port configuration. EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 95

Thru-drive Models PVM74/81 *Right-hand only Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. 12, (4.2) Lifting point.375-16 UNC thd. 1, (.39) deep with SAE drain M1 thd. 1, (.39) deep with ISO drain Alt. drain port "F". See options on page 17. Alt. drain port "F". See options on page 17. Outlet port "C". See options on page 16. Inlet port "B". See options on page 16. 87, (3.42) 2X Outlet gauge port "K". See options on page 17. Inlet port "B". See options on page 16. TO MOUNTING FACE 249,6 (9.83) Inlet gauge port "K". See options on page 17. Left hand rotation with Pressure Compensator Max. Adj. stop. One rotation will change displacement 6,1-7,4 l/min (1.7-1.9 USgpm) at 18 rpm 4,8 (.16) 143,3 (5.64) Load sense port "J". See options on page 17. 113,6 (4.47) 319,1 w/o max adj stop (12.56) 334,8 (13.18) 194,8 (7.67) 146,1 (5.75) C/G location 33,9 (1.33) Alt. drain port "F". See options on page 17. 86, (3.39) 86, (3.39) 2X T1 Inlet gauge port "K". See options on page 17. 92, (3.62) "A2" 45, (1.77) 91, (3.58) 114, 114, (4.49) (4.49) Right hand rotation with Load Sensing Control and 2-bolt A flange Outlet gauge port "K". See options on page 17. 11, (4.33) 14.5 (.57) Outlet port "C". See options on page 16. Drain port "F". See options on page 17. 277,6 (1.93) 322.6 (12.7) 246,6 (9.71) 181,6 (7.15) 33, (1.3) PVM74/18 is not available with left hand rotation in any port configuration. 96 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Thru-drive Models PVM74/81 *Right-hand only Dimensions in millimeters (inches) 68,3 (2.69) S R3 R1 R2" 43,3 (1.7) S R3 R1 R2 Coupling Length Code SAE A, 9T 64,5 (2.54) A,G SAE A, 11T 65,3 (2.57) B,H SAE B, 13T 95,3 (3.75) C,J SAE B-B, 15T 95,3 (3.75) D,K SAE C, 14T 95,3 (3.75) E,L SAE C-C, 17T 91,8 (3.61) F,M Coupling length (See table) B Adapter Flange To mtg, face To mtg, face With adapter plate 372,6 (14.68) 335,1 (13.19) View rotated 9 4X 35, (1.38) 4X W Coupling (see table) 25, (.98) A1 92, (3.62) Without adapter plate A2 Coupling (see table) Coupling length (see table) A1 T2 T1 Right hand rotation with Load Sensing Control and ISO or SAE 2-/4-bolt B adapter flange Model code Position 25 Description A SAE A, 9T, 16/32 DP, 3 pressure angle, involute spline B SAE A, 11T, 16/32 DP, 3 pressure angle, involute spline C SAE B, 13T, 16/32 DP, 3 pressure angle, involute spline D SAE B-B, 15T, 16/32 DP, 3 pressure angle, involute spline E SAE C, 14T, 12/24 DP, 3 pressure angle, involute spline F SAE C-C, 17T, 12/24 DP, 3 pressure angle, involute spline G For ISO 8-A2HW pad with a 9T SAE spline H For ISO 8-A2HW pad with a 11 T SAE spline J For ISO 1-A2/B4HW pad with a 13T SAE spline K For ISO 1-A2/B4HW pad with a 15T SAE spline L For ISO 125-A2/B4HW pad with a 14T SAE spline M For ISO 125-A2/B4HW pad with a 17T SAE spline Model Code Position 25 Pilot O-ring O-ring Pilot Support Flange Bolt Dia. Dia. Depth Depth 2-bolt 4-bolt Mounting Points 4-bolt 2-bolt R1 R2 R3 S T1 T2 W A1 A2 A,B SAE A SAE Ø82,6 Ø89,65 2, (.8) 9,/8, 375-16 UNC-2B thd. N/A N/A N/A G,H 2-bolt (3.25) (3.53) 1,9 (.7) (.35/.31) 53,2 ISO 8 ISO Ø8,5 Ø89,75 2,7 (.11) 9,/8, M1 thd. N/A N/A N/A 54,5 (3.15) (3.53) 2,6 (.1) (.35/.31) (2.15) C,D SAE B SAE Ø11,65 Ø18,5 2, (.8) 12,5/11,5.5-13 UNC-2B thd..5-13 UNC-2B thd..5-13 UNC-2B 44,9 73, J,K 2-/4-bolt (4.) (4.25) 1,9 (.7) (.49/.45) thd..98 deep (1.77) (2.87) ISO 1 ISO Ø1,5 Ø18,75 2,7 (.11) 12,5/11,5 M12 thd. M1 thd. M12 thd. 25, deep 44,19 7, (3.94) (4.28) 2,6 (.1) (.49/.45) (1.74) (2.76) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 97

Thru-drive Models PVM74/81 *Right-hand only Dimensions in millimeters (inches) C Adapter Flange To mtg, face 347,6 (13.69) 4X 35, (1.38) 4X W T1 A1 92, (3.62) To mtg, face 335,1 (13.19) T2 A1 A2 View rotated 9ϒ Left hand rotation with Pressure Compensator and ISO or SAE 2-/4-bolt C Adapter Flange Model Code Position 25 Pilot O-ring O-ring Pilot Support Flange Bolt Dia. Dia. Depth Depth 2-bolt 4-bolt Mounting Points R1 R2 R3 S T1 T2 W A1 A2 E,F SAE C SAE Ø127,5 Ø133,45 2, (.8) 15,5/14,5.625-11 UNC-2B thd..5-13 UNC-2B thd..5-13 UNC-2B 57,25 9,5 L,M 2-/4-bolt thd..98 deep (2.25) (3.56) ISO 125 ISO Ø125,5 Ø133,75 2,7 (.11) 15,5/14,5 M16 thd. M12 thd. M12 thd. 25, deep 56,57 9, (4.92) (3.26) 2,6 (.1) (.61/.57) (2.23) (3.54) 98 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Side-ported Models PVM98/16 Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. 121, (4.76) Alt. drain port F. See options on page 17. Lifting point.375-16 UNC thd.1, (.39) deep with SAE drain M1 thd. 1, (.39) deep with ISO drain Alt. drain port F. See options on page 17. 2X 95, (3.74) Outlet port C. See options on page 16. Outlet gauge port K. See options on page 17. Left hand rotation with Pressure Compensator Inlet port B. See options on page 16. Inlet gauge port K. See options on page 17. 162, (6.38) 342,4 (13.48) 115,5 (4.55) w/o max adj stop 357,8 (14.9) 33,9 (1.33) Inlet port B. See options on page 16. To mounting face 276,9 (1.9) Max. Adj. stop. One rotation will change displacement 7,9-8,7 l/min (2.1-2.3 USgpm) at 18 rpm Inlet gauge port K. See options on page 17. 16,4 (.65) 17,6 (6.72) Load sense port J. See options on page 17. 214,6 (8.45) 155,7 (6.13) C/G location 92,5 (3.64) 9, (3.54) Outlet gauge port K. See options on page 17. 17,5 (4.23) 35,5 (1.4) Outlet port C. See options on page 16. 37, (1.46) Alt. drain port F. See options on page 17. 7, 7, (2.76) (2.76) 98, 91, Drain port F. See (3.86) (3.58) options on page 17. 119, 119, (4.69) (4.69) Left hand rotation with Load Sensing Control 266,9 (1.51) 322,6 (12.7) 2X 194,5 (7.66) 35,6 (12.3) PVM98/16 is not available in left hand rotation with rear ports. EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 99

Thru-drive Models PVM98/16 Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. 121, (4.76) Alt. drain port "F". See options on page 17. Lifting point.375-16 UNC thd. 1, (.39) deep with SAE drain M1 thd. 1, (.39) deep with ISO drain Alt. drain port "F". See options on page 17. 2X 95, (3.74) 347,9 (13.7) Outlet port "C". See options on page 16. Inlet port "B". See options on page 16. 162, (6.38) Outlet gauge port "K". See options on page 17. Left hand rotation with Pressure Compensator Inlet gauge port "K". See options on page 14. 342,4 (13.48) 115,5 (4.55) w/o max adj stop 357,8 (14.9) 33,9 (1.33) Inlet port "B". See options on page 16. To mounting face 276,9 (1.9) 92,5 (3.64) Max. Adj. stop. One rotation will change displacement 7,9-8,7 l/min (2.1-2.3 USgpm) at 18 rpm 2X T1 17,3 (.68) 17,6 (6.72) Outlet gauge port "K". See options on page 17. Load sense port "J". See options on page 17. 36,6 (1.44) 15, (5.91) 17,5 (4.23) 214,6 (8.45) 164,4 (6.47) C/G location 2X 37, (1.46) 9, (3.54) Alt. drain port "F". See options on page 17. Inlet gauge port "K". See options on page 17. A2* 45, (1.77) 98, 91, (3.86) (3.58) 119, 119, (4.69) (4.69) Right hand rotation with 2-bolt A flange and Load Sensing Control 42, (1.65) Outlet port "C". See options on page 16. Drain port "F". See options on page 17. 2X 194,5 (7.66) 266,9 (1.51) PVM98/16 is not available in left hand rotation with rear ports. 1 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Thru-drive Models PVM98/16 Dimensions in millimeters (inches) 68,3 (2.69) S Coupling length (see table) With adapter plate B Adaptor Adapter Flange To mtg, face To mtg, face 372,6 (14.68) 372,9 (14.68) R3 R1 R2 R1 COMBINE WITH R2 EXISTING GRAPHIC Coupling (see table) FOR THIS PAGE 25, (.98) 35, (1.38) (4 plcs) 4X 35, A1 (1.38) 92, 4X W (3.62) Support mounting points 43,3 (1.7) S A1 92, (3.62) R3 Without adapter plate Coupling (see table) Coupling length (see table) T2 T1 T2 T1 Coupling Length Code SAE A, 9T 64,5 (2.54) A,G SAE A, 11T 65,3 (2.57) B,H SAE B, 13T 95,3 (3.75) C,J SAE B-B, 15T 95,3 (3.75) D,K SAE C, 14T 95,3 (3.75) E,L SAE C-C, 17T 91,8 (3.61) F,M Model code Position 25 Description A SAE A, 9T, 16/32 DP, 3 pressure angle, involute spline B SAE A, 11T, 16/32 DP, 3 pressure angle, involute spline C SAE B, 13T, 16/32 DP, 3 pressure angle, involute spline D SAE B-B, 15T, 16/32 DP, 3 pressure angle, involute spline E SAE C, 14T, 12/24 DP, 3 pressure angle, involute spline F SAE C-C, 17T, 12/24 DP, 3 pressure angle, involute spline G For ISO 8-A2HW pad with a 9T SAE spline H For ISO 8-A2HW pad with a 11 T SAE spline J For ISO 1-A2/B4HW pad with a 13T SAE spline K For ISO 1-A2/B4HW pad with a 15T SAE spline L For ISO 125-A2/B4HW pad with a 14T SAE spline M For ISO 125-A2/B4HW pad with a 17T SAE spline 36,4 A1 To To mtg, face (14.19) 36,4 V Support A2 (14.19) mounting A1 View Rotated 9 points (4 plcs) A2 View Rotated 9 Right hand rotation with Load Sensing Control Right hand rotation with CV compensation and ISO or SAE 2-/4-bolt B adapter flange Model Code Position 25 Pilot O-ring O-ring Pilot Support Flange Bolt Dia. Dia. Depth Depth 2-bolt 4-bolt Mounting Points 4-bolt 2-bolt R1 R2 R3 S T1 T2 W A1 A2 A,B SAE A SAE Ø82,6 Ø89,65 2, (.8) 9,/8, 375-16 UNC-2B N/A N/A N/A 53,2 G,H 2-bolt (3.25) (3.53) 1,9 (.7) (.35/.31) thd..59 deep ISO 8 ISO Ø8,5 Ø89,75 2,7 (.11) 9,/8, M1 thd. N/A N/A N/A 54,5 (3.15) (3.53) 2,6 (.1) (.35/.31) x 18, deep (2.15) C,D SAE B SAE Ø11,65 Ø18,5 2, (.8) 12,5/11,5.5-13 UNC-2B thd..5-13 UNC-2B thd..5-13 UNC-2B 44,9 73, J,K 2-/4-bolt (4.) (4.25) 1,9 (.7) (.49/.45) thd..98 deep (1.77) (2.87) ISO 1 ISO Ø1,5 Ø18,75 2,7 (.11) 12,5/11,5 M12 thd. M1 thd. M12 thd. 25, deep 44,19 7, (3.94) (4.28) 2,6 (.1) (.49/.45) (1.74) (2.76) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 11

Thru-drive Models PVM98/16 Dimensions in millimeters (inches) C Adapter Flange To mtg, face 372,9 (14.68) 4X 35, (1.38) 4X W Support mounting points T1 T2 A1 92, (3.62) To mtg, face 36,4 (14.19) View Rotated 9 A1 A2 Left hand rotation with Pressure Compensator and ISO or SAE 2-/4-bolt C adapter flange Model Code Position 25 Pilot O-ring O-ring Pilot Support Flange Bolt Dia. Dia. Depth Depth 2-bolt 4-bolt Mounting Points R1 R2 R3 S T1 T2 W A1 A2 E,F SAE C SAE Ø127,5 Ø133,45 2, (.8) 15,5/14,5.625-11 UNC-2B thd..5-13 UNC-2B thd..5-13 UNC-2B 57,25 9,5 L,M 2-/4-bolt thd..98 deep (2.25) (3.56) ISO 125 ISO Ø125,5 Ø133,75 2,7 (.11) 15,5/14,5 M16 thd. M12 thd. M12 thd. 25, deep 56,57 9, (4.92) (3.26) 2,6 (.1) (.61/.57) (2.23) (3.54) 12 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

End-ported Models PVM131/141 Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. 369,4 (14.54) 34, (1.34) 23,4 (9.7) 132,7 (5.22) 131, (5.16) B inlet port 172, (6.77) C outlet port Optional drain port F 115, (4.53) Adjustable maximum stop option. Torque locknut to 37-45 Nm (27-33 lb ft). One turn of screw wil change pump displacement 5,7 cm 3 /rev (.35 in 3 /rev). Turn CCW to destroke. K Outlet gage port Lef t hand rotation with Pressure Compensator K Inlet gage port 65, (2.56) 2 plcs. 55, (2.17) 2 plcs. 143,5 (5.65) 111,5 (4.39) 2 plcs. 346,1 (13.63) max. length w/o max. adj. stop 122,6 (4.83) 2 plcs. K Inlet gage port F2 132,7 (5.22) 11,5 (4.35) R.H. 94,5 (3.72) L.H. J Load sense signal port 18,6 (7.11) 55, (2.17) Optional drain port F F3 F drain port 192,6 (7.58) 2 plcs. 33,6 (13.2) Lifting point.5-13 UNC-2B thd. 18, (.79) dp. 2 plcs. 25, (.98) 16, (4.17) B inlet port B2 4 plcs. K Inlet gage port 49,7 (1.95) 64, (2.52) 14,2 (4.1) 91,5 (3.6) Right hand rotation with Load Sensing Control K Outlet gage port C outlet port C2 4 plcs. EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 13

Side-ported Models PVM131/141 Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. C outlet port C2 4 plcs. 341,1 (13.43) gage port spotface 318,1 (12.52) gage port spotface 28,4 (11.4) ref. View A - A Outlet port 172, (6.77) 65, (2.56) 2 plcs. 111,5 (4.39) 2 plcs. 115, (4.53) 34, (1.34) 369,4 (14.54) 28,4 (11.4) C L outlet 23,4 (9.7) port Optional drain port F 1, (3.94) Adjustable maximum stop option. Torque locknut to 37-45 Nm (27-33 lb ft). One turn of screw will change pump displacement 5,7 cm 3 /rev (.35 in 3 /rev) 55, (2.16) 2 plcs. 346,1 (13.63) max. length w/o max. adj. stop 122,6 (4.82) 2 plcs. 132,7 (5.22) 131, (5.16) Outlet gage port K Outlet port C. Inlet gage port K Left hand rotation with Pressure Compensator J Load sense signal port Inlet gage port K 132,7 (5.22) 11,5 (4.35) R.H. 94,5 (3.72) L.H. 18,6 (7.11) Inlet port B 143,5 (5.7) F2 A 55, (2.17) F3 Optional drain port F F drain port Lifting point.5-13 UNC-2B thd. 18. (.79) dp. 2 plcs. 192,6 (7.58) 2 plcs. 298.6 (11.76) B2 4 plcs. Inlet port B 16, (4.17) 7, (2.76) 7, (2.76) 95. (3.74) A Outlet gage port K Right hand rotation with Load Sensing Control 14 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Thru-drive Models PVM131/141 Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. 172, (6.77) 143,5 (5.65) 34, (1.33) 23,4 (9.7) Drain port F. See options on page 17. 122,6 (4.83) 28,4 (11.4) 347,1 (13.67) 44,7 (1.76) 369,4 (14.54) 346,1 (13.63)w/o max. adj. stop CL outlet port 8, (3.15) See coupling code below See output shaft below 8,5 (.33) 14, (.55) A9 19, (.75) A11 132,7 (5.22) Outlet port C. See options on page 16. Q2 See table below Q See table below Inlet port B. See options on page 16. Left Hand Rotation with Pressure Compensator and SAE 2-bolt A Flange (no adapter) SAE port 116,1 (4.57) ISO port 15, (5.91) 111,5 (4.39) 131, (5.16) Load sense port J. See options on page 17. 18,6 (7.11) Inlet port B. See options on page 16. SAE.5-13 UNC-2B thd. 1. deep min. or ISO M12 x 27. deep min. Outlet port C. See options on page 16. 65, (2.56) 15, (.59) 132,7 (5.22) 55, (2.16) 28,4 (11.4) 55, (2.17) 173, (6.81) 192,6 (7.58) 35,6 (12.3) 298,6 (11.76) Inlet gage port K 54,5 (2.15) 16, (4.17) 11,5 (.45) Inlet gage port K. See options on page 17. 1, (3.94) SAE.5-13 UNC-2B thd. 1.19 deep min. or ISO M12 x 31. deep min. Model Code Position 25 Q1 Thru-drive Flange Q2 2-bolt Thread A,B SAE J744-82-2.375-16 UNC-2B Ø82.625/82.575 bore thd..8 deep G,H ISO 319/2-8A2 Ø8.75/8.25 bore M1 thd. x 18, deep 95, (3.74) 4, (1.57) 4, (.16) 45, (1.77) Alt. drain port F. See options on page 17. Outlet gage port K. See options on page 17. SAE port 116,1 (4.57) ISO port 15, (5.91) 313,6 (12.35) Right Hand Rotation with Load Sensing Control and SAE 2-bolt A Flange (no adapter) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 15

Thru-drive Models PVM131/141 Dimensions in millimeters (inches) 69,7 (2.74) O-ring (furnished) Coupling (See table) 14, (.55) Model Code Position 25 Description A For SAE A pad with a 9T, 16/32 DP, 3 pressure angle, involute spline B For SAE A pad with a 11T, 16/32 DP, 3 pressure angle, involute spline Output shaft 14T 12/24 DP external involute spline C SAE B, 13T, 16/32 DP, 3 pressure angle, involute spline D SAE B-B, 15T, 16/32 DP, 3 pressure angle, involute spline E SAE C, 14T, 12/24 DP, 3 pressure angle, involute spline F SAE C-C, 17T, 12/24 DP, 3 pressure angle, involute spline G For ISO 8-A2HW pad with a 9T SAE spline H For ISO 8-A2HW pad with a 11T SAE spline J For ISO 1-A2/B4HW pad with a 13T SAE spline K For ISO 1-A2/B4HW pad with a 15T SAE spline L For ISO 125-A2/B4HW pad with a 14T SAE spline M For ISO 125-A2/B4HW pad with a 17T SAE spline B Adapter Flange 372,1 (14.65) R2-2 places 35, (1.38) 4 places R3 4 places R4 (4 plcs) 359,6 (14.16) R1 92, (3.62) 4 places Right Hand Rotation with SAE 2-/4-Bolt B Flange and ISO 1 Adapter Flange Model Code Position 25 R1 Thru-drive Flange R2 2-bolt Thread R3 4-bolt Thread R4 Support Mounting Points C,D SAE J744-11-2 & -4.5-13 UNC-2B.5-13 UNC-2B.5-13 UNC-2B Ø11,675/11.625 bore 12,5/11,5 deep.98 deep.98 deep.98 deep J,K ISO 319/2-1A2 & B2 M12 M12 M12 Ø1,75/1.25 bore 12,5/11,5 deep 25, deep 25, deep 25, deep 16 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Thru-drive Models PVM131/141 Dimensions in millimeters (inches) C Adapter Flange 359,6 (14.16) S1 92, (3.62) 4 places S4 4 places 35, (1.38) 4 places 372,1 (14.65) S2 2 places S3 4 places Left Hand Rotation with SAE 2-/4-bolt C and ISO 125 Adapter Flange Model Code Position 25 S1 Thru-drive Flange S2 2-bolt Thread S3 4-bolt Thread R4 Support Mounting Points E,F SAE J744-127-2 & -4.625-11 UNC-2B.5-13 UNC-2B.5-13 UNC-2B Ø127,75/127.25 bore 15,5/14,5 deep.98 deep.98 deep.98 deep L,M ISO 319/2-125A2 & B4 M16 M12 M12 Ø125,75/125.25 bore 15,5/14,5 deep 25, deep 25, deep 25, deep Port B * B2 C * C2 F2 F3 SAE 2.5 inch dia. SAE J518 Code 61, low pressure.5-13 UNC-2B thd. 1.19 deep minimum 1.25 inch dia. SAE J518 Code 62, high pressure.5-13 UNC-2B thd. 1. deep minimum 146,8 (5.78) 114,9 (4.52) ISO 64mm diameter. ISO 6162 Type II, 315 M12 thread 31, deep minimum 32mm diameter. ISO 6162, 4 M12 thread 27, deep minimum 148,5 (5.85) 116,6 (4.59) *4-bolt flange port. See page 11 for load sensing, drain, and gage port threads. EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 17

Mounting Flange Options Dimensions in millimeters (inches) H 2-bolt A, B & C Flange ISO & SAE E F 2-bolt B Flange 4-bolt C or D Flange ISO & SAE L G L K K G A H A 45 J pilot J pilot 2-bolt or 4-bolt Series Flange Code Flange Description A E F G H J K L PVM18 2-bolt A SAE J744-82-2 Ø11,14 53,2 16,4 Ø82,53 +.2 -.3 PVM2 A (4.38) (2.9) (4.19) (Ø3.249) +. -.1 PVM18 2-bolt B ISO 319/2-8A2HW Ø11,14 54,5 19, Ø79,98 +.2 -.3 PVM2 A (4.38) (2.15) (4.29) (Ø3.15) +. -.1 PVM18 PVM2 PVM45 2-bolt C SAE J744-11-2 14,36 73, 146, Ø11,58 +.2 PVM5 B -.3 PVM57 (.565) (2.87) (5.75) _ (Ø3.999) ±.1 PVM63 PVM18 PVM2 PVM45 2-bolt D ISO 319/2-1A2HW 14,14 7, 14, Ø1,/99,95 PVM5 B (special) (.557) (2.76) (5.51) (Ø3.937/3.935) PVM57 PVM63 E SAE J744-127-2 ( C ) 17,4 9,5 181, Ø127,/126,95 PVM57 PVM63 2-bolt (.685) (3.562) (7.125) (Ø5./4.998) PVM74 C F ISO 319/2-125A2HW 18, 9, 18, Ø125,/124,95 PVM81 (.79) (3.543) (7.9) (Ø4.921/4.919) PVM98 G SAE J744-127-4 ( C ) 14,2 57,25 114,5 Ø127,/126,95 PVM16 4-bolt (.559) (2.254) (4.58) (Ø5./4.998) PVM131 C PVM141 H ISO 319/2-125B4HW 14, Ø125,/124,95 8, 16, (.551) (Ø4.921/4.919) (3.15) (6.299) PVM131 4-bolt J SAE J744-152-4 ( D ) 2,6 8,82 161,64 Ø152,4/152,35 (.812) (3.182) (6.364) (Ø6./5.998) PVM141 D K ISO 319/2-16B4HW 18, Ø16,/159,95 1, 2, (.79) (Ø6.299/6.297) (3.937) (7.874) *Flanges for PVM2 and PVM5 are shown on pages 73 and 8, respectively. 18 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Shaft Options Dimensions in millimeters (inches) SAE Splined Shaft B spline C A D SAE Spline Shaft Max. Torque Model Series Designation Shaft Code A max. B C D Nm (lb. in.) SAE J744-16-4 SAE A (9T) 3 15,88 (.625) 9T 16/32 DP 37, (1.46) 32, (1.26) 58 (517) PVM18/2 SAE J744-19-4 SAE A (11T) 4 19,5 (.75) 11T 16/32 DP 3, (1.18) 38, (1.5) 123 (11) SAE J744-22-4 SAE B (13T) 7 21,81 (.859) 13T 16/32 DP 33, (1.31) 41, (1.61) 28 (185) SAE J744-25-4 SAE B-B (15T) 8 24,98 (.983) 15T 16/32 DP 38, (1.5) 46, (1.81) 337 (2987) PVM45/5 SAE J744-22-4 SAE B (13T) 7 21,81 (.859) 13T 16/32 DP 33, (1.31) 41, (1.61) 28 (185) SAE J744-25-4 SAE B-B (15T) 8 24,98 (.983) 15T 16/32 DP 38, (1.5) 46, (1.81) 337 (2987) SAE J744-22-4 SAE B (13T) 7 21,81 (.859) 13T 16/32 DP 33, (1.31) 41, (1.61) 28 (185) PVM57/63 SAE J744-25-4 SAE B-B (15T) 8 24,98 (.983) 15T 16/32 DP 38, (1.5) 46, (1.81) 337 (2987) SAE J744-32-4 SAE C (14T) 11 31,22 (1.23) 14T 12/24 DP 48, (1.89) 56, (2.2) 64 (566) SAE J744-32-4 PVM74/81 SAE C (14T) 11 31,22 (1.23) 14T 12/24 DP 48, (1.89) 56, (2.2) 64 (566) PVM98/16 SAE J744-38-4 SAE C-C (17T) 12 37,57 (1.479) 17T 12/24 DP 54, (2.13) 62, (2.44) 1215 (1,75) SAE J744-32-4 SAE C (14T) 11 31,22 (1.23) 14T 12/24 DP 48, (1.89) 56, (2.2) 64 (566) PVM131/141 SAE J744-38-4 SAE C-C (17T) 12 37,57 (1.479) 17T 12/24 DP 54, (2.13) 62, (2.44) 1215 (1,75) SAE J744-44-4 SAE D (13T) 14 43,71 (1.721) 13T 8/16 DP 67, (2.63) 75, (2.95) 1215 (1,75) EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 19

Shaft Options Dimensions in millimeters (inches) SAE Keyed Shaft E key C B A D Max. SAE Keyed Shaft Shaft Torque Model Series Designation Code A B C D E Nm (lb. in.) SAE J744-16-1 SAE A 1 15,88 (.625) 17,73 (.698) 24, (.94) 32, (1.26) 4, (.157) 58 (517) PVM18/2 SAE J744-19-1 SAE 19-1 2 19,5 (.75) 21,23 (.836) 24, (.94) 32, (1.26) 4,81 (.189) 14 (918) SAE J744-22-1 SAE B 5 22,22 (.875) 25,12 (.989) 33, (1.31) 41, (1.61) 6,35 (.25) 135 (12) SAE J744-25-1 SAE B-B 6 25,37 (.999) 28,22 (1.111) 38, (1.5) 46, (1.81) 6,35 (.25) 215 (19) PVM45/5 SAE J744-22-1 SAE B 5 22,22 (.875) 25,12 (.989) 33, (1.31) 41, (1.61) 6,35 (.25) 135 (12) SAE J744-25-1 SAE B-B 6 25,37 (.999) 28,22 (1.111) 38, (1.5) 46, (1.81) 6,35 (.25) 215 (19) PVM57/63 SAE J744-25-1 SAE B-B 6 25,37 (.999) 28,22 (1.111) 38, (1.5) 46, (1.81) 6,35 (.25) 215 (19) SAE J744-32-1 SAE C 9 31,75 (1.25) 35,32 (1.39) 48, (1.89) 56, (2.2) 7,93 (.312) 45 (398) SAE J744-32-1 9 31,75 (1.25) 35,32 (1.39) 48, (1.89) 56, (2.2) 7,93 (.312) 45 PVM74/81 SAE C (398) PVM98/16 SAE J744-38-1 SAE C-C 1 38,1 (1.5) 42,39 (1.67) 54, (2.13) 62, (2.44) 9,52 (.375) 765 (677) SAE J744-32-1 SAE C 9 31,75 (1.25) 35,32 (1.39) 48, (1.89) 56, (2.2) 7,93 (.312) 45 (398) PVM131/141 SAE J744-38-1 SAE C-C 1 38,1 (1.5) 42,39 (1.67) 54, (2.13) 62, (2.44) 9,52 (.375) 765 (677) SAE J744-44-1 13 44,45 (1.75) 49,46 (1.95) 67, (2.63) 75, (2.95) 11,11 (.438) 12 SAE D (1,62) 11 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Shaft Options Dimensions in millimeters (inches) D key ISO Keyed Shaft E A C B Max. ISO Keyed Shaft Shaft Torque Model Series Designation Code A B C D E Nm (lb. in.) ISO 319/2 E2N 15 19,9 (.786) 8,5 (.335) 36 (1.42) 6 (.236) 22,5 (.886) 113 (1) PVM18/2 ISO 319/2 E25N Short Spigot 16 25 (.984) 8,5 (.335) 42 (1.65) 8 (.315) 28, (1.12) 215 (19) ISO 319/2 E25N 17 25 (.984) 1 (.393) 42 (1.65) 8 (.315) 28, (1.12) 215 (19) PVM45/5 ISO 319/2 E25N 17 25 (.984) 1 (.393) 42 (1.65) 8 (.315) 28, (1.12) 215 (19) PVM57/63 ISO 319/2 E25N 17 25 (.984) 1 (.393) 42 (1.65) 8 (.315) 28, (1.12) 215 (19) ISO 319/2 E32N 18 32 (1.26) 1 (.393) 58 (2.28) 1 (.394) 35, (1.378) 45 (398) PVM74/81 ISO 319/2 E32N 18 32 (1.26) 1,5 (.413) 58 (2.28) 1 (.394) 35, (1.378) 45 (398) PVM98/16 ISO 319/2 E4N 19 4 (1.57) 1,5 (.413) 82 (3.23) 12 (.472) 43, (1.693) 87 (77) PVM131/141 ISO 319/2 E32N 18 32 (1.26) 1 (.393) 58 (2.28) 1 (.394) 35, (1.378) 45 (398) ISO 319/2 E4N 19 4 (1.57) 1 (.393) 82 (3.23) 12 (.472) 43, (1.693) 87 (77) (1)ISO 8mm pilot only B (2)ISO 8mm pilot only D *Torque of non-thru-drive PVM pump, or combined torque of PVM thru-drive pump and thru-driven pump. NOTE: In those cases where geometric tolerances of mounting are critical, or where specific tolerance ranges are required and not specified, consult Eaton Engineering for specific limits. EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 111

Shaft Selection Data SAE Splined Shafts Max. Torque Max. Thru-drive Output Torque Model Series Shaft Designation Shaft Code Nm (lb. in.) Nm (lb. in.) SAE J744-16-4 (SAE A, 9T) 3 58 (513) Exceeds maximum input torque PVM18/2 SAE J744-19-4 (SAE A, 11T) 4 123 (11) Exceeds maximum input torque SAE J744-22-4 (SAE B, 13T) 7 28 (185) 123 (11) SAE J744-25-4 (SAE B-B, 15T) 8 337 (2987) 123 (11) PVM45/5 SAE J744-22-4 (SAE B, 13T) 7 28 (185) 28 (185)* SAE J744-25-4 (SAE B-B, 15T) 8 337 (2987) 337 (2987) SAE J744-22-4 (SAE B, 13T) 7 28 (185) 28 (185)* PVM57/63 SAE J744-25-4 (SAE B-B, 15T) 8 337 (2987) 337 (2987) SAE J744-32-4 (SAE C, 14T) 11 64 (566) 337 (2987) PVM74/81 SAE J744-32-4 (SAE C, 14T) 11 64 (566) 515 (456) PVM98/16 SAE J744-38-4 (SAE C-C, 17T) 12 1215 (1,75) 515 (456) SAE J744-32-4 (SAE C, 14T) 11 64 (566) 64 (566) PVM131/141 SAE J744-38-4 (SAE C-C, 17T) 12 1215 (1,75) 64 (566) SAE J744-44-4 (SAE D, 13T) 14 1215 (1,75) 64 (566) SAE Keyed Shafts Max. Torque Max. Thru-drive Output Torque Model Series Shaft Designation Shaft Code Nm (lb. in.) Nm (lb. in.) SAE J744-16-1 (SAE A ) 1 58 (513) Exceeds maximum input torque PVM18/2 SAE J744-19-1 (SAE 19-1 ) 2 14 (92) Exceeds maximum input torque SAE J744-22-1 (SAE B ) 5 135 (12) 123 (11) SAE J744-25-1 (SAE B-B ) 6 215 (19) 123 (11) PVM45/5 SAE J744-22-1 (SAE B ) 5 135 (12) 135 (12)* SAE J744-25-1 (SAE B-B ) 6 215 (19) 215 (19)* PVM57/63 SAE J744-25-1 (SAE B-B ) 6 215 (19) 215 (19)* SAE J744-32-1 (SAE C ) 9 45 (398) 337 (2987) PVM74/81 SAE J744-32-1 (SAE C ) 9 45 (398) 45 (398)* PVM98/16 SAE J744-38-1 (SAE C-C ) 1 765 (677) 515 (456) SAE J744-32-1 (SAE C ) 9 45 (398) 45 (398)* PVM131/141 SAE J744-38-1 (SAE C-C ) 1 765 (677) 64 (566) SAE J744-44-1 (SAE D ) 13 12 (1,62) 64 (566) ISO Keyed Shafts Max. Torque Max. Thru-drive Output Torque Model Series Shaft Designation Shaft Code Nm (lb. in.) Nm (lb. in.) ISO 319/2 E2N (B mount only) 15 113 (1) Exceeds maximum input torque PVM18/2 ISO 319/2 E25N (B mount only) 16 215 (19) Exceeds maximum input torque ISO 319/2 E25N (D mount only) 17 215 (19) 123 (11) PVM45/5 ISO 319/2 E25N 17 215 (19) 215 (19)* PVM57/63 ISO 319/2 E25N 17 215 (19) 215 (19)* ISO 319/2 E32N 18 45 (398) 337 (2987) PVM74/81 ISO 319/2 E32N 18 45 (398) 45 (398)* PVM98/16 ISO 319/2 E4N 19 87 (77) 515 (456) PVM131/141 ISO 319/2 E32N 18 45 (398) 45 (398)* ISO 319/2 E4N 19 87 (77) 64 (566) Maximum total torque of the thru-drive pump and the thru-driven pump(s). Maximum torque that can be applied to the thru-driven pump(s). *This value is limited by the maximum input torque. 112 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

Port Options Inlet and Outlet Ports Inlet/Outlet Port Option Port Model Series (per model code, page 5) Code Inlet Port B Outlet Port C Inch Flange 2 SAE J518 Code 61, standard pressure. SAE J518 Code 61, standard pressure. 1.25 inch diameter,.4375-14 x 1.12 bolt holes.75 inches diameter,.375-16 x.88 bolt holes PVM18/2 Metric Flange 4 ISO 6162 Type II, 315. 31,75mm diameter, M1 x 28 bolt holes ISO 6162 Type II, 315. 19,5mm diameter, M1 x 22 bolt holes Inch Tube 1 SAE J514 O-ring 2, for 1-1/4 inch O.D. tube SAE J514 O-ring -12, for 3/4 inch O.D. tube Metric Tube 3 ISO 6149-1, M42 thread ISO 6149-1, M27 thread British Parallel Pipe 5 ISO 228-1:1994 (E), G 1-1/4 thread ISO 228-1:1994 (E), G 3/4 thread Inch Flange 2 SAE J518 Code 61, standard pressure. SAE J518 Code 61, standard pressure. 2. inch diameter,.5-13 x 1.6 bolt holes 1. inch diameter,.375-16 x.87 bolt holes PVM45/5 Metric Flange 4 ISO 6162 Type II, 315. ISO 6162 Type II, 315. 51mm diameter, M12 x 27 bolt holes 25mm diameter, M1 x 22 bolt holes Inch Tube 1 SAE J514 O-ring -24, for 1-1/2 inch O.D. tube SAE J514 O-ring -16, for 1 inch O.D. tube Metric Tube 3 ISO 6149-1, M48 thread ISO 6149-1, M33 thread British Parallel Pipe 5 ISO 228-1:1994 (E), G 1-1/2 thread ISO 228-1:1994 (E), G1 thread Inch Flange 2 SAE J518 Code 61, standard pressure. SAE J518 Code 61, standard pressure. 2. inch diameter,.5-13 x 1.6 bolt holes 1. inch diameter,.375-16 x.88 bolt holes PVM57/63 Metric Flange 4 ISO 6162 Type II, 35. 51mm diameter, M12 x 29 bolt holes ISO 6162 Type, 35. 25mm diameter, M1 x 23 bolt holes Inch Tube 1 SAE J514 O-ring -24, SAE J514 O-ring (End ported models only) for 1-1/2 inch O.D. tube -16 for 1 inch O.D. tube Metric Tube (End ported models only) 3 ISO 6149-1, M48 thread ISO 6149 1, M33 thread PVM74/81 Inch Flange 2 SAE J518 Code 61, standard pressure. SAE J518 Code 61, standard pressure. 2. inch diameter,.5-13 x 1.19 bolt holes 1. inch diameter,.375-16 x.88 bolt holes Metric Flange 4 ISO 6162 Type II, 315. ISO 6162 Type, 4. 51mm diameter, M12 x 2 bolt holes 25mm diameter, M1 x 17 bolt holes PVM98/16 Inch Flange 2 SAE J518 Code 61, standard pressure. SAE J518 Code 61, standard pressure. 2.5 inch diameter,.5-13 x 1.19 bolt holes 1. inch diameter,.375-16 x.88 bolt holes Metric Flange 4 ISO 6162 Type I, 35. ISO 6162 Type I, 35. 64mm diameter, M12 x 31 bolt holes 25mm diameter, M1 x 23 bolt holes PVM131/141 Inch Flange 2 SAE J518 Code 61, standard pressure. SAE J518 Code 62, high pressure. 2.5 inch diameter,.5-13 x 1.19 bolt holes 1.25 inch diameter,.5-13 x 1. bolt holes Metric Flange 4 ISO 6162 Type II, 315. ISO 6162 Type, 4. 64mm diameter, M12 x 31 bolt holes 32mm diameter, M12 x 27 bolt holes EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 113

Port Options Drain, Load Sensing, and Gauge Ports Inlet/Outlet Port Option Port Model Series (per model code, page 5) Code Drain Port F Load Sensing Port J Gauge Port K Inch Flange or Tube 1, 3 SAE J514 O-ring,.5 O.D. SAE J514 O-ring,.25 O.D. SAE J514 O-ring,.25 tube. tube..75-16 UNF 2B thread tube..4375-2 UNF 2B thread.4375-2 UNF 2B thread PVM18/2 Metric Flange or Tube 3, 4 ISO 6149-1 O-ring M18 x 1,5 thread ISO 6149-1 O-ring M12 x 1,5 thread ISO 6149-1 O-ring M12 x 1,5 thread British Parallel Pipe 5 ISO 228-1:1994 (E) ISO 228-1:1994 (E) ISO 228-1:1994 (E) G 1/2 thread G 1/4 thread G 1/4 thread Inch Flange or Tube 1, 3 SAE J514 O-ring,.625 O.D. SAE J514 O-ring,.25 O.D. SAE J514 O-ring,.375 O.D. tube. tube..875-14 UNF 2B thread tube..4375-2 UNF 2B thread.5625-18 UNF 2B thread PVM45/5 Metric Flange or Tube 3, 4 ISO 6149-1 O-ring M22 x 1,5 thread ISO 6149-1 O-ring M12 x 1,5 thread ISO 6149-1 O-ring M14 x 1,5 thread British Parallel Pipe 5 ISO 228-1:1994 (E) ISO 228-1:1994 (E) ISO 228-1:1994 (E) G 1/2 thread G 1/4 thread G 1/4 thread Inch Flange or Tube 1, 2 SAE J514 O-ring,.625 O.D. SAE J514 O-ring,.375 O.D. SAE J514 O-ring,.375 O.D. tube. PVM57/63 tube..875-14 UNF 2B thread tube..5625-18 UNF 2B thread.5625-18 UNF 2B thread Metric Flange or Tube 3, 4 ISO 6149-1 O-ring ISO 6149-1 O-ring ISO 6149-1 O-ring M22 x 1,5 thread M14 x 1,5 thread M14 x 1,5 thread Inch Flange 2 SAE J514 O-ring,.625 O.D. SAE J514 O-ring,.375 O.D. SAE J514 O-ring,.375 O.D. tube. PVM74/83 tube..875-14 UNF 2B thread tube..562-18 UNF 2B thread.5625-18 UNF 2B thread PVM98/16 Metric Flange 4 ISO 6149-1 O-ring ISO 6149-1 O-ring ISO 6149-1 O-ring M22 x 1,5 thread M14 x 1,5 thread M14 x 1,5 thread Inch Flange 2 SAE J514 O-ring,.625 O.D. SAE J514 O-ring,.375 O.D. SAE J514 O-ring,.375 O.D. tube. PVM131/141 tube..875-14 UNF 2B thread tube..562-18 UNF 2B thread.5625-18 UNF 2B thread Metric Flange 4 ISO 6149-1 O-ring ISO 6149-1 O-ring ISO 6149-1 O-ring M22 x 1,5 thread M14 x 1,5 thread M14 x 1,5 thread

Operating Requirements Inlet Pressure, case pressure, and operating temperature requirements Inlet Pressure Case Pressure Operating Temperature Rated Minimum Maximum Maximum Maximum Maximum Absolute, absolute Gauge Continuous Intermittent Peak Rated Intermittent ( (in. Hg) ( ( ( ( C ( F) C ( F) 1, (14.5),85 (5) 3,5 (5),5 (7) 2 (3) 3,5 (5) 82 (18) 14 (22) Hydraulic Fluids Minimum Viscosity @ Max. Recommended Operating Maximum Viscosity Intermittent Temperature of Viscosity Range at Startup 14 C (22 F) Fluid cst (SUS) cst (SUS) cst (SUS) Use antiwear hydraulic oil, or automotive type crankcase oil (designations SC, SD, SE, 16 to 4 (83 to 187) 1 (455) 1 (9) or SF) per SAE J183 FEB8 For more information, see Eaton publication 579. For operation on other alternative or environmentally friendly fluids, please contact your Eaton Representative. Fluid Cleanliness The M Series pumps are rated in anti-wear petroleum fluids with a contamination level of 2/18/13 (Eaton) or ISO 18/13. Operation in fluids with levels more contaminated than this is not recommended. Fluids other than petroleum, severe service cycles, or temperature extremes are cause for adjustment of these codes. Please contact your Eaton Representative for specific duty cycle recommendation. Eaton M Series pumps, as with any variable displacement piston pumps, will operate with apparent satisfaction in fluids up to the rating specified here. Experience has shown, however, that pump and hydraulic system life is not optimized with high fluid contamination levels (high ISO cleanliness codes). Proper fluid condition is essential for long and satisfactory life of hydraulic components and systems. Hydraulic fluid must have the correct balance of cleanliness, materials, and additives for protection against wear of components, elevated viscosity and inclusion of air. Essential information on the correct methods for treating hydraulic fluid is included in Eaton publication 561 Eaton Guide to Systemic Contamination Control Available from your local Eaton distributor. In this publication, filtration and cleanliness levels for extending the life of axial piston pumps and other system components are listed. Included is an excellent discussion of the selection of products needed to control fluid condition. Moment of Inertia (single pump rotating group) Model Moment of Inertia N-m (sec 2 ) lbf-in (sec 2 ) PVM18.12.14 PVM2.12.14 PVM45.36.32 PVM5.34.3 PVM57.52.457 PVM63.51.447 PVM74.78.691 PVM81.73.643 PVM98.132.1165 PVM16.123.186 PVM131.213.1889 PVM141.21.1856

Installation and Start-up Warning: Care should be taken that mechanical and hydraulic resonances are avoided in the application of the pump. Such resonances can seriously compromise the life and/or safe operation of the pump. Drive Data Mounting attitude can be either horizontal or vertical, using the appropriate case drain ports to ensure that the case remains full of fluid at all times. Consult your local Eaton Representative if a different arrangement is required. In those cases where geometric tolerances of mounting are critical, or where specific tolerance ranges are required and not specified, consult Eaton Engineering for specific limits. Direction of shaft rotation, viewed from the prime mover end, must be as indicated in the model designation on the pump either right hand (clockwise) or left hand (counterclockwise). Direct coaxial drive through a flexible coupling is recommended. If drives imposing radial shaft loads are considered, please consult your Eaton Representative. Start-up Procedure Make sure the reservoir and circuit are clean and free of dirt/debris prior to filling with hydraulic fluid. Fill the reservoir with filtered oil and fill to a level sufficient enough to prevent vortexing at the suction connection to pump inlet. It is good practice to clean the system by flushing and filtering, using an external slave pump. Caution: Before the pump is started, fill the case through the uppermost drain port with hydraulic fluid of the type to be used. The case drain line must be connected directly to the reservoir and must terminate below the oil level. Once the pump is started, it should prime within a few seconds. If the pump does not prime, check to make sure that there are no restrictions between the reservoir and the inlet to the pump, that the pump is being rotated in the proper direction, and that there are no air leaks in the inlet line and connections. Also check to make sure that trapped air can escape at the pump outlet. After the pump is primed, tighten the loose outlet connections, then operate for five to ten minutes (unloaded) to remove all trapped air from the circuit. If the reservoir has a sight gage, make sure the fluid is clear not milky. 116 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

This page intentionally blank. EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 117

This page intentionally blank. 118 EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29

This page intentionally blank. EATON Vickers PVM Industrial & Mobile Variable Displacement Piston Pumps V-PUPI-TM7-E February 29 119

Eaton Hydraulics Business USA 14615 Lone Oak Road Eden Prairie, MN 55344 USA Tel: 952-937-98 Fax: 952-294-7722 www.eaton.com/hydraulics Eaton Hydraulics Business Europe Route de la Longeraie 7 111 Morges Switzerland Tel: +41 () 21 811 46 Fax: +41 () 21 811 461 Eaton Hydraulics Business Asia Pacific 11th Floor Hong Kong New World Tower 3 Huaihai Zhong Road Shanghai 221 China Tel: 86-21-6387-9988 Fax: 86-21-6335-3912 29 Eaton Corporation All Rights Reserved Printed in USA Document No. V-PUPI-TM7-E Supercedes V-PP-MC-3-E, V-PP-MC-4-E February 29