Recommended with NESCAFÉ GOLD Barista Style. Experience the full range today.* TABLE OF CONTENTS SAFETY PRECAUTIONS...2-3 MACHINE OVERVIEW... 4 FIRST TIME USE & INITIAL RINSING...5 REFILLING WITH COFFEE... 6 PREPARING BEVERAGES...7-8 INDIVIDUAL ADJUSTMENTS TO YOUR PERSONAL TASTE... 9 NESCAFÉ GOLD Barista Style - Intense NESCAFÉ GOLD BLEND NESCAFÉ GOLD BLEND - Decaffeinated CLEANING...10- A premium blend of soluble coffee with added finely ground roast coffee beans. This intense blend delivers a sharp, full-bodied cup with a bouquet of deep aromas. A premium blend of Arabica beans that are golden roasted to perfection. Delivers a smooth cup with juicy aromas. With caffeine naturally removed with water, this decaffeinated version delivers the same perfect cup of NESCAFÉ GOLD BLEND with juicy aromas. DESCALING... - USER MANUAL We recommend using NESCAFÉ GOLD Barista Style coffee which is suited and tested for the NESCAFÉ GOLD BLEND Barista system. Alternatively, other freeze-dried coffee options can also be used. Fine powdered coffee is not recommended to be used in the NESCAFÉ GOLD BLEND Barista system as it will result in blockage issues. *All NESCAFÉ GOLD products are suitable for use and have been tested for the NESCAFÉ GOLD BLEND Barista system. www.nescafe.com.sg GREEN & ORANGE LIGHT SIGNALS... 17 RED ERROR SIGNALS... 18-19 TROUBLESHOOTING... 20-21
SAFETY PRECAUTIONS When using electrical appliances, basic safety precautions should always be followed, including the following: These instructions are to ensure you use this electric product safely and prevent you and associates from the risk of damage or hazard. Please read and follow carefully all indicated Warnings and instructions. Warnings : failure to follow these warnings may result in death or severe injury. Warnings: Unplug the cable immediately in a state of emergency. Do not place hands underneath the hot water jet or outlet during the preparation of the beverage (danger of burning). Always put a cup underneath the outlets when rinsing the machine. Ensure electrical plugs are clean and free of dust. It can cause an electric shock, short circuit or fire. Unplug the cable when the machine is not in use to avoid the risk of injury, burn, electric shock, electric leak or fire caused by dielectric degradation. Do not damage, destroy, remodel, bend, pull or twist the power plug forcedly. The plug can be damaged and cause fire or electric shock by placing heavy objects on it, taking it apart or modifying it. Do not handle plug with wet hands. Plug the machine only into mains voltage of 230 V - 50 Hz. Do not place coffee box near objects which could be affected by magnet. The heating element surface is subject to residual heat after use. Advised usage: Insert the plug in a socket which is properlywired. When using an extension cord, do not put many loads on one outlet. It can result in fire caused by abnormal heat. In the event that the plug and cord get hot, stop using the machine immediately (do not use the machine abroad). Do not unplug the machine by pulling the cord. It can cause a short circuit. Do not touch the plug with wet hands. It can cause an electric shock. This appliance is intended to be used in household only. It is not intended to be used in the following applications, and the guarantee may not apply for: - staff kitchen areas in shops, offices and other working environments; - farm houses; - by clients in hotels, motels and other residential type environments; This machine can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the machine in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised by an adult. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. The appliance must not be immersed. Do not put anything (hot water, milk, alcohol etc) other than potable water in the water tank. It can dirty or clog the inside of the machine and cause failure. We recommend the usage of soft water. Do not use the machine near fire or place it on hot surfaces (e.g. on top of electric hot plate). It can cause a fire. Clean machine periodically according to instructions in chapter «CLEANING». When cleaning the machine, unplug the machine and let it cool down. Do not clean the machine while it is still hot. You can burn yourself. SAFETY PRECAUTIONS The manufacturer is not liable for damage The coffee box is equipped with a permanent caused by improper use of the machine or magnet. Avoid placing the coffee box near failure to comply with the instructions of this appliances and objects that can be damaged manual. Such damages are also not covered by magnetism, e.g. credit cards, usb drives by the warranty. and other data devices, video tapes, television Children shall not play with the machine. and computer monitors with picture tubes, mechanical clocks, hearing aids and loud speakers. 2 3 Patients with pacemakers or defibrillators: Do not hold the coffee box directly over the pacemaker or defibrillator. Do not wash the power plug or the cord with water nor leave them in liquid, such as cleanser. It can cause a failure. Do not leave water in the water tank when the machine is not used over a long period of time. The water can become contaminated. Use fresh water every time you use the machine. Do not use the machine when it has a failure, does not work properly or indicates any possibility of failure. Do not put too much water in the water tank as it will spill over the power connector. Do not put a load on the machine and do not squeeze the machine in between two shelves. This could lead to damage. Further instructions: In some situations the machine requires a rinsing cycle. Before operating again, put a cup underneath the outlets. Drawer can only be inserted when the mixing chamber is inserted and locked. We recommend the use of NESCAFÉ GOLD, which has been tested with NESCAFÉ GOLD BLEND Barista system and particularly suits it. The system is not designed for fine soluble coffee (like for instance NESCAFÉ Espresso), nor agglomerated soluble coffee powder (like for instance NESCAFÉ Classic), and as well not for R&G coffee. Upon use of those coffee, the system will be blocked.
MACHINE OVERVIEW FIRST TIME USE AND INITIAL RINSING Water tank Top cover NESCAFÉ container Cleaning light see page 18-19 Mixing chamber rinsing light see page 18-19 Power button (ON/OFF) 5i Before using the machine for the first time: A initial rinse must be done. Perform a rinse with water tank filled to maximum level (approx. 1 L). Preferably use soft water. 51 52 min. 1/4 L No water indicator light see page 18-19 Place a container with a capacity of at least 1/4 L under the coffee outlet. Take water tank out. Put drinking water in the tank. Never put any liquid other than potable water in the tank! Menu icons 2 ON High velocity hot water jet Slider cover (green) Mixing chamber 53 1 54 5 ~25 sec Mixing chamber lock handle (blue) Drawer Re-attach the water tank to the main body. Plug in the power plug. CAUTION! Do not handle plug with wet hands. Plug the machine only into mains voltage of 230 V - 50 Hz. Switch machine on. Power button starts blinking green while machine is heating up for approx. 25 seconds. Power button and Espresso icon light steady green. Touch Espresso icon. Milk measuring cup Drip grid Drip tray 56 57 58 230 V 50 Hz 60 W max. bar 1 L ~3,4 kg 5-35 C C B A A = 178 mm B = 319 mm C = 285 mm Rinsing starts. Wait until it stops. Put rinsing water in the sink. After rinsing is finished all lights are steady green. Machine is now ready for use. 4 5
REFILLING WITH COFFEE PREPARING BEVERAGES 1 2 Menu icons Power button (ON/OFF) Espresso Suggested cup size: 100 ml 61 62 63 Latte Macchiato Suggested cup size: 300 ml Lungo Suggested cup size: 200 ml Push on the top cover and open it. Remove coffee box. Place coffee box as shown and remove cap. Cappuccino Suggested cup size: 300 ml Hot water function for cup preheating Americano Suggested cup size: 250 ml Black coffee options Espresso 64 65 6 Lungo Americano 71 72 Fill coffee box with suitable coffee (see indication below). Re-attach coffee box cap. Insert coffee box back to machine. The logo faces forwards. If you have difficulty to insert back coffee tank, please refer to section TROUBLESHOOTING, page 21. Place a cup. Remove drip tray when using a big mug. Touch the desired menu icon. 67 6i We recommend using NESCAFÉ GOLD Barista Style coffee which is suited and tested for the NESCAFÉ GOLD BLEND Barista system. Alternatively, other freeze-dried coffee options can also be used. Maximum filling volume for coffee tank: 0 g 73 74 7i Close top cover. Fine powdered coffee is not recommended to be used in the NESCAFÉ GOLD BLEND Barista system as it will result in blockage issues. Coffee powder is adversely affected by high temperatures and humidity. Please store it in a sealed container in a cool and dry location. Also, the coffee powder in the coffee tank should be used in good time, preferably within one month. The selected menu icon flashes. The extraction starts and stops automatically. To stop the extraction partway through, touch selected menu icon again and wait until light stops blinking. When selected menu icon stops flashing your coffee is ready. All lights are steady green. Enjoy your coffee. CAUTION! Your coffee will be hot! To heat up the cup before preparing coffee touch Cappuccino and Americano icon simultaneously. CAUTION! Hot water will flow out! Afterwards throw away water and continue with step 1. 6 7
PREPARING BEVERAGES INDIVIDUAL ADJUSTMENTS TO YOUR PERSONAL TASTE Milk coffee options You can adjust the strength of the coffee by changing the amount of hot water: Latte Macchiato Cappuccino 81 Pour milk* into the supplied measuring cup: - Latte Macchiato: 60 ml - Cappuccino: 50 ml 82 Pour milk into the cup. * NESCAFÉ recommends to use milk with at least 3 % fat. To adjust volume, please follow procedure below Menu Parameters (ml) Espresso type coffee Black coffee Mug-size black coffee Standard Initial quantity setting ~60 ml ~0 ml ~200 ml Strongest ~40 ml ~70 ml ~100 ml Minimum quantity Maximum quantity ( ) ( setting ) Weakest setting ( ) ~120 ml ~210 ml ~300 ml Note: For Latte Macchiato & Cappuccino, cup parameter can not be adjusted Latte Macchiato Cappuccino 83 84 85 2 sec 91 92 93 Place a cup. Remove drip tray when using a Latte Macchiato glass. Touch the desired menu icon. The selected menu icon starts flashing. Put a cup in place. Touch and hold the menu icon for the beverage you wish to adjust for 2 seconds. The power button light changes to orange. The selected menu icon lights green. Coffee extraction starts. When the selected menu icon stops flashing green you can adjust the amount of hot water. 86 Hot water/coffee extraction starts and stops automatically. To stop the extraction partway through, touch selected menu icon again and wait until light stops blinking. Nevertheless some coffee will continue to flow as long as the icon is flashing. 87 When selected menu icon stops flashing your coffee is ready. All lights are steady green. Enjoy your coffee. CAUTION! Your coffee will be hot! 8i To heat up the cup before preparing coffee touch Cappuccino and Americano icon simultaneously. CAUTION! Hot water will flow out! Afterwards throw away water and continue with step 1. 94 +/ When the beverage reaches the desired amount touch the menu icon to stop. If you do not touch machine will stop at the maximum water level! 9i After changing the setting... Once you have changed the setting, the new amount of hot water will be used as the standard amount when you make the next coffee. (The new amount of hot water is not reset when you turn off the power.) When a small cup is used, the coffee may overflow the cup if you set the amount of hot water too high. To adjust to a new amount of hot water, repeat the above procedure (the current setting will be overwritten). Resetting initial beverage recipes 1 Connect the power plug. 2 Check that the power is OFF. 3 Touch and hold the Cappuccino icon THEN the power button simultaneously. 4 Release the buttons when all the icon lights start flashing fast in green. 5 Machine is now back to factory settings. 6 Initial rinsing must be performed (see page 5). 8 9
CLEANING - OVERVIEW OF THE PARTS Cleaning is to be performed when the maintenance icon starts blinking ( ). Regular maintenance of the machine ensures a better in-cup quality and a longer lifetime. About the water tank: Coffee box - do not rinse! Coffee box cap CLEANING DRAWER & MIXING CHAMBER 1/2 CAUTION! Put none of the parts into a dishwasher! OFF! CAUTION! Coffee box 111 112 11 3 Do not touch the protrusion (connection part) on the bottom of the water tank. If you touch the protrusion on the bottom of tank when it has water in it, the water may spill from the tank. Dosing unit - rinsing OK! Magnet (Do not expose to magnetic sensitive appliances!) Coffee box scraper Switch machine off. Unplug power plug. Pull out the drawer. Press down the blue lock handle. Water tank connection part Dosing unit (constructed from the three parts below) Lower disk No. 2* 1 1 11 6 Inside the drawer: Upper disk No. 1* Dosing unit housing No. 3* *No. is engraved on the dosing unit housing Check that the lock handle is down. Remove the mixing chamber. Press the slider cover inwards from the both sides and pull it out. Sometimes the residue hardens, making it a little bit difficult to remove. Release the lock under the mixing chamber. High velocity hot water jet Slider cover (green) No. 4** Mixing chamber mesh Mixing chamber 117 118 min. 2 minutes 11 9 To remove the mixing chamber, pull down on the lock handle. Mixing chamber lock handle (blue) **No. is engraved on the slider cover Drawer Rinse drawer and slider cover under hot water. Wipe with a soft damp cloth. Soak mixing chamber in hot water for at least 2 minutes. If coffee is still adhered, scrape it off gently. Dry away moisture. 10 11
CLEANING DRAWER & MIXING CHAMBER 2/2 CAUTION! Put none of the parts into a dishwasher! CLEANING DRIP TRAY, TANKS & DOSING UNIT 1/2 CAUTION! Put none of the parts into a dishwasher! Check inside! Top OFF! 10 12 12 11 12 131 132 13 Bottom Check the holes inside the mixing chamber: If the holes are blocked with coffee, rinse again with hot water. Push down lever until you hear a Click. In case mesh has been removed: Check orientation of the mesh (the mesh has a top and a bottom side). Switch machine off. Unplug power cord. Rinse drip tray with hot water and clean it with a brush. Rinse and clean water tank. Afterwards refill with fresh, potable water and insert it to machine. No. 3 13 12 12 12 134 135 136 No. 1 Push mesh into original position. Ensure it is fully inserted. Align arrows on slider cover and main body. Press the slider cover in until you hear a Click. Make sure that step 11 has been correctly followed. Push mixing chamber into the main body. Ensure it is fully inserted. Make sure that coffee tank is empty. Turn the dosing unit clockwise and remove it from the coffee box. Turn over the dosing unit and remove the upper disk No. 1. Using the thumbs turn in the direction of the OPEN arrow until you hear a Click. 12 12 17 Pull up blue handle to lock mixing chamber. Slide drawer in until you feel the Click. 137 138 Put your fingers into the openings and remove lower disk No. 2. Lower disk No. 2 Dosing unit housing No. 3 Upper disk No. 1 Check whether all three parts are there. 139 Wipe away the dirt with a soft damp cloth. Soak disk No. 1 and disk No. 2 in hot water. 12 13
DESCALING 1/2 CLEANING DRIP TRAY, TANKS & DOSING UNIT 2/2 CAUTION! Put none of the parts into a dishwasher! If you don t descale your machine according to the following recommendations issues and even break down could happen. We recommend to descale your machine depending on water hardness and consumption but at least twice a year (see table below). Water hardness i 11 10 Hard water Medium Soft Remove coffee box cap and scraper. Clean cap and scraper with a soft damp cloth. Do not clean the coffee box with flowing water! Descaling after... cups 300 ppm 250 cups 180 ppm 500 cups 80 ppm 750 cups Read instructions and safety information on packaging of descaling agent. Do not wash surface of machine using descaling agent. Rinse and dry parts carefully before reassembling! Ideally let it dry for one night. Do not use a hair dryer deformation may result! No. 1 80 g 12 13 No.3 No.3 Align marks No. 3 with No. 2 and fit together. The label No. 3 gets visible. 1 Using the thumbs of both hands turn the lower disk No. 2 in the direction of the CLOSE arrow until you hear a Click. D ag es en ca t lin g No.2 2 min. 700 ml 3 No. 3 Turn over the dosing unit housing and align the triangular portions on the dosing unit housing No. 3 and upper disk No. 1. Dissolve 80 g of descaling agent in 700 ml of water. Do not use hot water! Remove drip tray. Place a container with a capacity of at least 700 ml under the coffee outlet. Take water tank out. Pour descaling solution into water tank. Insert water tank to machine. Central protrusion 7 sec 17 4 5 6 Fit the scraper with the protrusion in the centre facing inwards and insert it into the corresponding recess. Put coffee box back on dosing unit. With the dosing unit held steady at the bottom, close by turning the coffee box clockwise until it stops. To enter the descaling mode, start with machine off, then press on Espresso icon & power button for 7 seconds. All menu icons start flashing. Release the buttons. Espresso icon and power button lights up steady green. Touch Espresso icon to start descaling process (icon starts flashing green). Descaling solution is discharged: First from high velocity hot water jet, then from coffee outlet.
DESCALING 2/2 7 8 GREEN & ORANGE LIGHT SIGNALS 9 ~25 sec 5 min 5 min Wait 5 minutes to let the descaling solution work. Touch Espresso icon to start again descaling process (icon starts flashing green). Descaling solution is discharged: First from high velocity hot water jet, then from coffee outlet. Wait another 5 minutes to let descaling solution work. Throw away water from container. Carefully rinse water tank. 10 11 12 min. 700 ml Heating up mode Power button: flashing green All menu icons: OFF Initial rinse mode Power button: steady green Espresso icon: steady green (see page 5) Operation mode Power button: steady green All menu icons: steady green +/ Place a container with a capacity of at least 700 ml under the coffee outlet. Put drinking water in the tank. Insert water tank to machine. Touch Espresso icon to start rinsing process (icon starts flashing green). Water is first discharged from the high velocity hot water jet and then from the coffee outlet. Preparation mode Power button: steady green Selected menu icon: flashing green Cup warming adjustment mode Power button: steady orange Cappuccino & Americano icon: flashing green In this mode you can adjust the amount of water dispensed when preheating the cup (see page 7+8). 13 Access this mode by touching Cappuccino and Americano icon simultaneously during 2 seconds. +/ When Espresso icon stops flashing, touch Espresso icon again to start second rinsing cycle (icon starts flashing green). Water is first discharged from the high velocity hot water jet and then from the coffee outlet. Throw away water from container. Carefully rinse water tank. Fill up water tank with drinking water. Insert water tank back to machine. i To quit the descaling mode, turn off the machine. Coffee amount adjustment mode Power button: steady orange Selected menu icon: flashing green at the beginning, then steady green when adjustment possible (see page 9) When the desired amount of water is reached touch the Cappuccino and Americano icon simultaneously to stop. If you do not touch machine will stop at the maximum level! 17 ECO mode (After 5 minutes power turns OFF automatically) Power button: OFF All menu icons: OFF
RED ERROR SIGNALS 1/2 RED ERROR SIGNALS 2/2 Error signal lights ERROR SIGNAL: PROCEDURE TO SOLVE THE PROBLEM: ERROR SIGNAL: PROCEDURE TO SOLVE THE PROBLEM: Cleaning light Drawer not correctly inserted Water tank empty / descaling required If water tank is EMPTY: If water tank is NOT EMPTY: Mixing chamber rinsing light 191 192 Descaling Agent No water indicator light Americano icon: flashing green Power button: steady red Insert drawer correctly. Push firmly inside. No water indicator light: flashing red Power button: steady green Refill water tank and insert it back to machine correctly. Press green icon to finish beverage preparation. Descale the machine according to descaling procedure on page -17. Coffee box not correctly inserted Rinsing mixing chamber required 191 192 Espresso icon: flashing green Power button: steady red Remove coffee box and insert it correctly. Close top cover. If you have difficulty to insert back coffee tank, please refer to section TROUBLESHOOTING, page 21. Mixing chamber rinsing light: flashing red Espresso icon: steady green Power button: steady red Remove coffee cup and place container with a capacity of 200 ml under the coffee outlet. Touch Espresso icon. Rinsing process starts. Error has occurred ON OFF Coffee dust in machine, cleaning required/recommended Cleaning light: FLASHING RED Cleaning is recommended Cleaning light: STEADY RED Cleaning is required 20 min All menu icons: OFF Power button: fast flashing red Switch machine off and wait 20 minutes. Afterwards switch machine on. If power button still flashes red contact support desk. Cleaning light: flashing / steady red All menu icons: steady green Power button: steady green / red 18 19 Clean dosing unit (see page 13-). Put coffee box in place and make a rinse. Additionally clean mixing chamber, slider cover and drawer (see page 11-12).
TROUBLESHOOTING 1/2 TROUBLESHOOTING 2/2 CAUSE OF TROUBLE: PROCEDURE TO SOLVE THE PROBLEM: CAUSE OF TROUBLE: PROCEDURE TO SOLVE THE PROBLEM: 201 202 21 1 212 All menu icons: OFF Power button: OFF Machine cannot be switched on. Check if the power plug is plugged correctly into a mains power socket. If yes, check your electricity supply. If machine still cannot be switched on contact support desk. If machine still cannot be switched on, contact support desk through the information found on the back page. Coffee box cannot be inserted anymore. Power button: steady red Espresso icon: flashing green Clean dosing unit and its parts (see page 13-). Reassemble it with coffee box. Put coffee box back to machine. Do not push it in by force! Doing so may damage it! Remove coffee cup and place a container with a capacity of at least 200 ml under the coffee outlet. 201 202 21 3 21 4 Coffee is not being dispensed properly from the coffee outlet. Stop preparation. Clean mixing chamber, slider cover and drawer according to cleaning procedure on page 12-13. Gently swivel coffee box to the front until Espresso icon lights up. Hold coffee box in this position. Touch Espresso icon while holding coffee box in same position until coffee extraction starts. Then push coffee box down. 1 3 21 5 21 6 2 Only hot water is being dispensed. Tap on the top cover and open it. Remove coffee box and refill it according to procedure on page 7. Close top cover. 20 21 Touch Espresso icon to start the rinsing process. Afterwards throw away water from container.
www.nescafe.com.sg