HYLA NST Cleaning System

Transcription

1 Owner s Manual

2 HYLA NST Cleaning System The HYLA NST Cleaning System aspirates and cleans the air through a waterbased filtration process. The system is intended for household use only. Applications: Usual domestic dry vacuuming Deep cleaning with Electro Brush and Turbo Brushes Wet vacuuming Wet cleaning of hard floors Wet cleaning of carpeted floors and upholstery Specifications: Voltage: 110 V, 60 Hz HYLA Power: 850 W/7.7 Amps + Electro Brush: 200 W/1.65 Amps Max Air flow: 100 cu ft/min Water pan capacity: 1 gallon 2

3 3

4 Important Safety Instructions When using an electrical appliance, basic precautions should always be followed, including the following: PLEASE READ ALL INSTRUCTIONS BEFORE USING THE HYLA NST CLEANING SYSTEM 4 WARNING To reduce the risk of fire, electric shock, or injury: Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. Use indoors only. Do not allow to be used as a toy. Close attention is necessary when used by or near children. Use only as described in this manual. Use only manufacturer's recommended attachments. Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, left outdoors, or dropped into water, return it to a service center. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated rooms. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. Do not handle plug or appliance with wet hands. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. Turn off all controls before unplugging. Use extra care when cleaning on stairs. Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.

5 This appliance is provided with double insulation. Use only identical replacement parts. See Instructions for Servicing of Double-Insulated Appliances. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes. Do not use without water as filter in the water pan. Always turn off this appliance before connecting or disconnecting electro brush. The unit is intended for attended operation only. SAVE THESE INSTRUCTIONS SERVICING OF DOUBLE-INSULATED APPLIANCES A double-insulated appliance is marked with one or more of the following: The words "DOUBLE INSULATION" or "DOUBLE INSULATED" or the double insulation symbol square within a square. In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing a double-insulated appliance requires extreme care and knowledge of the system, and should be done by qualified service personnel. Replacement parts for a double-insulated appliance must be identical to the parts they replace. 5

6 Components 1 1. Motor Unit Assembly 2. Water Pan Assembly 2 3. Trolley Assembly 4. NST Separator 3 4 6

7 Preparation for Use Fill the Water Pan with fresh, clean water up to the top of the pin located in the center of the Water Pan. 7

8 HYLA Accessories 1. Flexible Hose 2. Telescopic Wand 3. Crevice Tool 4. Transparent Nozzle Set 5. Synthetic Bristle Brush 6. Natural Bristle Brush 7. Noise Reducer 8. Multi-Purpose Brush

9 NST Electro Brush Set 1. NST Electro Brush 2. Flexible Electro Hose 3. Telescopic Wand

10 Deep Cleaning of Carpeted Floors WITH ELECTRO BRUSH Set-up for the Electro Brush Set Always turn off the main switch of the HYLA system before connecting or disconnecting the Electro Brush! To assemble ensure the Electro Brush is firmly set on a flat surface and swivel neck is in parked upright locked position. Directly face the Electro Brush to align the fully extended Telescopic Wand and gently insert spring button into position. Insert the handle of the Flexible Electro Hose into the Telescopic Wand. Align the handle with cord canal. Hold the electro cord plug while sliding the electro cord upward in the cord canal. Open outlet cover and insert plug. Clip excess cord to the lower portion of the Telescopic Wand. Take loose end of Flexible Electro Hose and connect into the HYLA Water Pan Plug electro cord into the Motor Unit Assembly outlet. GETTING READY TO USE THE ELECTRO BRUSH Turn on the main switch on the HYLA. To activate Electro Brush, release from its parked upright locked position by pressing the button located to the left of the swivel neck. You will notice a green light indicating operation. Now you are ready to clean! In order to turn off the Electro Brush, place handle in parked upright locked position. Then turn off the main switch on the HYLA. TROUBLESHOOTING The Electro Brush is equipped with an electronic circuit board for safety purposes. The red light located to the right of the Electro Brush is an indication the motor has been shut off to avoid overload. Place in parked upright locked position and turn off HYLA. After clearing any objects, press the red reset button located to the rear right of the Electro Brush. You may restart by turning on the main switch on the HYLA. MAINTENANCE Disconnect power from the Electro Brush. Textile fibers can be removed from the brush by cutting them and vacuuming. 10

11 Deep Cleaning of Upholstery WITH HAND TURBO BRUSH (Optional) The Hand Turbo Brush is air driven. It is designed for dry pick up only. A crevice tool is integrated. Maintenance: Disconnect the power cord from the power source Textile fibers can be removed from the brush by carefully cutting them and vacuuming Dry Vacuuming WITH MULTI-PURPOSE BRUSH The Multi-Purpose Brush can be used for hard floors and carpeted floors. It is designed for dry pick up use only. 11

12 Wet Vacuuming Do not use the NST Electro Brush, Hand Turbo Brush or Multi-Purpose Brush on wet surfaces! Fill the Water Pan with 1 /2 the water, which will reach the middle of the center pin (approx. 1 /2 gallon). Use caution when vacuuming liquids not to exceed maximum level in the Water Pan (top of the center pin). Blowing Remove Exhaust Grid on Motor Unit Assembly, Connect Flexible Hose to the Exhaust. 12

13 After Each Use 1. Turn off the main switch and disconnect the power cord from the power source, 2. Empty the Water Pan immediately after each use and rinse with clean water, 3. Wipe the underside of the Motor Unit Assembly using a wet cloth. Do not rinse the Motor Unit Assembly with water! 4. It is important to vent and store the HYLA System as shown, which will allow it to dry quickly after every use. Warning! Disconnect the Power Cord from the power source before removing the Motor Unit Assembly from the Water Pan! DO NOT use the system without water! The HYLA NST Cleaning System is not designed for vacuuming quantities of mineral dust! DO NOT vacuum flammable liquids! 13

14 Additional Applications Vacuuming of mattresses, pillows, blankets & more Extract any dirt particles or dust Intake of any spills or water fills 14

15 Suction of dust on delicate plants, silks & more Vacuuming of upholstery, furniture & more Lighter vacuuming of curtains, drapes & more 15

16 Optional Accessories and Attachments 1. Electro Polisher 2. Floor Turbo Brush 3. Inflator/Deflator Set 4. Hand Turbo Brush 5. Natural Floor Bristle Brush Also available Long/Extended Hoses. more information on additional accessories or attachments, please contact your local distributor

17 HYLA Disinfectants HYLA Air Disinfectant is especially formulated for use with the HYLA Cleaning System. When added to the water in your Water Pan, the air is filtered, cleaned, and disinfected from germs, bacteria and mildew! HYLA Surface Disinfectant is especially formulated for use with the HYLA Cleaning System, which has the combined effect of cleaning and disinfecting while making surfaces germ, bacteria and mildew-free! HYLA Fragrances HYLA Fragrances are available in Four Seasons! Each kit includes four 2-fl oz bottles of exclusive scents. 17

18 HYLA NST Wet Cleaning System (Optional) This system is an integral part of the HYLA NST Cleaning System and is designed for the wet cleaning of: Most hard floors (ceramics, tiles, vinyl, etc.) Most kinds of carpets Upholstery & car seats Additional Spraying Function Specifications: Fresh Water Tank: 0.8 gallon Cleaning capacity per Fresh Water Tank filling: sq ft for carpeted floors sq ft for hard floors 18

19 19

20 2 Components Fresh Water Tank 2. Connection Cap with Tube 3. Flexible Suction Hose with attached Fresh Water Tube 4. Fresh Water Tube 5. Hard Floor Nozzle 6. Carpet Nozzle 7. Upholstery Nozzle 8. Spray Nozzle 9. HYLA Cleanser for hard floors 10. HYLA Cleanser for carpeted floors & upholstery 11. Telescopic Wand

21 Preparation for Use: Fill the Fresh Water Tank with maximum of 0.8 gallon of water, Fill Water Pan with 1 /2 the water, which will reach the middle of the center pin (approx. 1 /2 gallon), Mount the Fresh Water Tank on top of the Motor Unit Assembly, Screw the Connection Cap in firmly and connect the air pressure tube to the back of the Motor Unit Assembly, Connect the Flexible Suction Hose to the Water Pan and connect the Fresh Water Tube to the Fresh Water Tank Connection Cap. 21

22 Wet Cleaning of Hard Floors Connect the Fresh Water Tube to the Hard Floor Nozzle, Turn on the main switch and pull the valve trigger to start the water flow, Clean the floor by moving the Nozzle back and forth with the suction wand held at an angle allowing clearance of the squeegee strip from the floor, Release the valve trigger and dry the cleaned floor by moving the Nozzle backwards with the suction wand held at an angle allowing direct contact of the squeegee strip with the floor, Use Caution during wet cleaning so you do not exceed the maximum level in the Water Pan (top of center pin). Warning! Wet floors may be slippery! 22

23 Wet Cleaning of Carpeted Floors Connect the Fresh Water Tube to the Carpet Nozzle, Turn on the main switch and pull the valve trigger to start the water flow, Wash the carpet by moving the Nozzle back and forth with the suction wand held at an angle allowing clearance of the front edge of the Nozzle from the carpet. Do not soak the carpet! Release the valve trigger and dry the cleaned carpet by moving the Nozzle backwards with the suction wand held at an angle allowing direct contact of the front edge of the Nozzle with the carpet. Use caution during wet cleaning so you do not exceed maximum level in the Water Pan (top of center pin). 23

24 Wet Cleaning of Upholstery Connect the Upholstery Nozzle to the suction hose, Turn on the main switch and pull the valve trigger to start the water flow, Wash upholstery by moving the Upholstery Nozzle back and forth held at an angle allowing clearance of front edge from the upholstery. Do not soak the upholstery! Release the valve trigger and dry the cleaned upholstery by moving the nozzle Upholstery Nozzle backward held at an angle allowing direct contact of front edge with the upholstery. Use caution during wet cleaning so you do not exceed maximum level in the Water Pan (top of the center pin). 24

25 Spraying Remove Exhaust Grid on the back of the Motor Unit Assembly, Connect the Flexible Hose into the Exhaust, Firmly screw the Connection Cap and connect the air pressure tube to the back of the Motor Unit Assembly, Connect the Spray Nozzle to the Flexible Hose and connect the Fresh Water Tube, Turn on the main switch and pull the valve trigger to start the water flow, Use the water spray to wash or wet surfaces, Release the valve trigger to stop the water as you blow the surface with air. 25

26 Warning! Use only HYLA liquid cleansers. Using other cleansers may damage your system! Before refilling the Fresh Water Tank, empty the Water Pan and refill it with 1 /2 the water, which will reach the middle of the center pin (approx. 1 /2 gallon). Service: Refer to the Limited Factory Warranty located in your warranty card for detailed information regarding technical support. If you should have any questions regarding applications, operation or technical support for your HYLA System, please contact the local HYLA Distributor from whom your system was purchased. 26 HYLA honors the Limited Factory Warranty included with the system when purchased through an authorized independent HYLA Distributor. Warranty will not be honored for purchases from external sources! HYLA ONLY honors warranty for HYLAs purchased from authorized Distributors by in-home demonstrations not vacuum stores or via Internet. Warranty is NOT an option for unauthorized parties due to inaccessibility of parts as they are NOT qualified, authorized HYLA service personnel.

27 If your Distributor is not available or unable to service your product, contact HYLA U.S. Corporate Headquarters in Florida for assistance in locating an independent Distributor in your area or us through our website. Please be sure to have your serial number available, which is located under the handle on top of the HYLA. Distributor Stamp: Imported by HYLA U.S. Gassmann, Inc East Newport Center Drive Deerfield Beach, FL Tel: CERTIFICATE No. Q-201 ISO 9001 EMBED CorelPhotoPaint.Image.8 All rights reserved, including the right to technical modifications without impairing the quality or performance of the HYLA NST Cleaning System. US NST

28 US NST 0606