Actuators and Sensors Products
CONTENT
1 2 3 4 Pneumatic solenoid valves for mobile applications > Double Pneumatic Solenoid Valve Block 01 > Multiple Pneumatic Valve Block 02 > Pneumatic Solenoid Valve 2.2 mm 2.0 mm 0.8 mm 03-05 WET PIN SOLENOIDS FOR HYDRAULIC VALVES > Wet Pin On/Off DC Solenoids NG6 06-08 > Coil NG6 09 > Wet Pin Proportional Solenoid NG6 10 > Proportional Solenoid w/ LVDT NG6 11-12 > Wet Pin Proportional Square Solenoids NG6 13-14 > Wet Pin On/Off DC Solenoid NG10 15 > Coil NG10 16 > Wet Pin Proportional Square Solenoids NG10 17-18 > Proportional Solenoid w/ LVDT NG10 19-20 DISTANCE SENSORS FOR WET PIN SOLENOIDS > LVDT (Linear Variable Differential Transformer) 21 > Position Switch for Core Tubes 22 DC Solenoids > C-Frame Solenoid 23 > D-Frame Solenoid 24 > Push/Pull DC Solenoid, closed Type 25 5 6 pressure sensors FOR MOBILE APPLICATIONS > Pressure Sensor 26-27 CUSTOMIZED PRODUCTS > Individual and customized Products 28
Double pneumatic solenoid valve block Part No. D60 23 00X 02 Typically used for two-corner air suspension in passenger cars and light commercial vehicles. 2x 2/2 valves Prepared for chassis mounting in mobile applications Equipped with connectors for 4 mm PA tubes, others on request Proven in car air suspension systems, can be used for other s D60 23 00X 02 12 V Working Pressure 17 bar Thermal Range of Operation -40 to +80 C Max. Environmental Temperature 110 C/h Duty Cycle 33%/5 min Nozzle Width 0.9 mm Pneumatic Connectors Ports 1&2 Voss, d=4.0 mm Pneumatic Connector Port P Legris, d=4.0 mm Electrical Connector Kostal Protection Class (With Mating Connector) IP6K8 1 1 Pneumatic solenoid valves
Multiple pneumatic solenoid valve block Part No. D78 230 0X 02 Typically used for four-corner or two-corner air suspension systems in passenger cars and light commercial vehicles Integrated valve block features up to five solenoid valves and one pressure sensor integrated into one housing 5x 2/2 valves, can also be equipped with 1-4x 2/2 valves Prepared for chassis mounting in mobile applications Equipped with connectors for 4mm / 6mm PA tubes Proven in car and LCV air suspension systems, can be used for other applications D60 23 00X 02 12 V Working Pressure 15 bar Thermal Range of Operation -40 to +80 C Max. Environmental Temperature 110 C/h Duty Cycle 33%/5 min Nozzle Width 4x0.9 mm 1x1.2 mm Pneumatic Connectors Ports 1-5 Voss, d=4.0 mm Pneumatic Connector Port P Legris, d=6.0 mm Electrical Connector FEP Pressure Sensor Supply Voltage 5 ± 0.2 V Pressure Sensor Pressure Range (abs.) 0.85 to 22.85 bar Pressure Sensor Output 0.5 to 4.5 V Pressure Sensor Accuracy <1.5% (-20 to +60 C) 2
Pneumatic solenoid 3/2 STANDALONE valve, 2.2 mm Part No. Type 547 (available 2012) Pressure resistant DC solenoid valve for air and other fluids 2/2- or 3/2-Valve variants possible with different electric and pneumatic interfaces, coil with isolation class H DIN EN 175301-803A Class of protection IP67 and IP6K9K Voltage and interface variants on demand No. Type 547 12 to 24 V Nominal Power at 100% ED 6.9 W Inlet Orifice 2.2 mm Outlet Orifice 3.0 mm Working Pressure 0 to 12.5 bar Ambient Temperature -40 to + 80 C Variants 2/2-, 3/2-Valve NC or NO 3 1 Pneumatic solenoid valves
Pneumatic solenoid valve, 2.0 mm Part No. Type 531 Pressure resistant DC solenoid valve for low-pressure-fluids and vacuum Technical Data 2/2- or 3/2-Valve with different interfaces possible as NO- or NC-version, special version for medical applications with high internal corrosion protection Valve sealing of FKM, other materials are possible Different voltages possible Coil with isolation class B DIN EN 175301-803A Class of protection IP00 No. Type 531 6 to 48 V Nominal Power at 100% ED 6.5 W Inlet Orifice 2.0 mm Outlet Orifice 2.0 mm Working Pressure 0 to 1 bar Ambient Temperature +10 to + 50 C Variants 2/2-, 3/2-Valve NC or NO 4
Wet pin On/Off DC Solenoid-NG 6 Part No. C46 13 045 04 Force vs stroke curve Condition: 90% Nominal voltage and warmed up, ambient temperature 50 C. Designed for directional hydraulic valves with wet pin Quick response time Push type Mounting central thread M 20 1 Exchange of the coil without opening the hydraulic circuit Manual override function Insulation class of coil: F (H available on request) Core tube diameter = 23 mm Electrical connector acc. to DIN EN 175301-803 A Enclosure protection: IP65 C46 13 045 04 24 V Nominal Resistance at 20 C 19 Ω ± 5% Working Stroke 2.8 mm Total Stroke (min.) 6.0 mm Nominal Current 1.25 A Nominal Power at 20 C 30 W Pressure Resistance (dyn.) 210 bar Ambient Temperature -30 to +50 C NOTE: Coil and Core Tube can be ordered separately. WET PIN SOLENOIDS 2 6
Wet pin On/Off DC Solenoid-NG6 Part No. C46 13 046 04 Force vs stroke curve Designed for directional hydraulic valves with wet pin Push type Small hysteresis and quick response time Mounting central thread M 19 1 Emergency manual override Insulation class of coil: F (class H available on request) Electrical connector acc. to DIN EN 175301-803 A Enclosure protection class: IP65 Core tube diameter = 22 mm C46 13 046 04 24 V Working Stroke 4.0 mm Total Stroke 7.0 mm Nominal Solenoid Force See F-S curve Nominal Current 1.4 A Nominal Resistance at 20 C 17.6 Ω ± 5% Pressure Resistance (dyn.) 210 bar NOTE: Coil and Core Tube can be ordered separately. 7 2 WET PIN SOLENOIDS
Wet pin On/Off DC Solenoid-NG6 Part No. 106 576 XX Force vs stroke curve Designed for directional hydraulic valves with wet pin Push type Small hysteresis and quick response time Mounting central thread M 19 1 Emergency manual override Insulation class of coil: F (class H available on request) Electrical connector acc. to DIN EN 175301-803 A Enclosure protection class: IP65 Core Tube Diameter = 23 mm 106 576 XX 24 V Working Stroke 2.5 mm Total Stroke (min.) 5.6 mm Nominal Solenoid Force 35 N Nominal Current 0.8 A Nominal Resistance at 20 C 21.8 Ω ± 7,5% Pressure Resistance (dyn.) 210 bar NOTE: Coil and Core Tube can be ordered separately. 8
Coil NG6 Part No. 449 00 X08 XX Coil for On/Off Solenoid with core tube diameter = 22mm Insulation class of coil: F (class H available on request) Electrical connector acc. to DIN EN 175301-803 A Enclosure protection: IP65 449 00 X08 26 449 00 X08 27 449 00 X08 28 449 00 X08 29 From 12 to 205 V on request 9 2 WET PIN SOLENOIDS
Wet pin Proportional Solenoid-NG 6 Part No. C46 53 072 04 Force vs stroke curve The curve shows an average without hysteresis. The tolerance range refers to averages without hysteresis. Used on proportional valves for precise controlling direction, pressure and flow. Push type Small hysteresis and quick response time Mounting central thread M 19 1 Emergency manual override Insulation class of coil: F (class H available on request) Electrical connector acc. to DIN EN 175301-803 A Enclosure protection class: IP65 Force vs CURRENT curve The curve shows the force at constant stroke of 1.5mm. C46 53 072 04 24 V Working Stroke 3.0 mm Total Stroke 7.0 mm Nominal Solenoid Force 59 N Nominal Force Hysteresis <6 N Nominal Current 0.8 A Nominal Resistance at 20 C 21.3 Ω ±5% Pressure Resistance (dyn.) 210 bar NOTE: Coil and Core Tube can be ordered separately. 10
Proportional Solenoid with LVDT NG6 Part No. C46 53 073 04 Force vs STROKE curve The curve shows an average without hysteresis. The tolerance range refers to averages without hysteresis. Used in electrical-hydraulic proportional close-loop systems. LVDT detects the position of armature, the deviation of position of armature will be sent to proportional amplifier and the position of armature and spool can be precisely controlled. Small hysteresis and quick response time Insulation class of coil: F (class H available on request) Electrical connector acc. to DIN EN 175301-803 A + M12 CLVDT Enclosure protection class: IP65 Force vs CURRENT curve OUTPUT VOLTAGE VS STROKE CURVE The curve shows the force at constant stroke of 1.5mm. of proportional solenoid C46 53 073 04 24 V Working Stroke 3.0 mm Total Stroke 7.0 mm Nominal Solenoid Force 59 mm Nominal Force Hysteresis <6 N Nominal Current 0.8 A Nominal Resistance at 20 C 21.3 Ω ±5% Pressure Resistance (dyn.) 210 bar of LVDT Supply Voltage 24 V ±20% Output Voltage linear Range 12 to 3 V Measurement Range ±3 mm Gain 1.5 V/mm ±3% Offset Range (typ.) ±1 mm Linearity (max.) ±1.5 Temperature Drift Gain 200 ppm/ C Working Temperature -10 to +100 C 11 2 WET PIN SOLENOIDS
12
Wet pin Proportional Square Solenoid-NG6 Part No. C47 53 087 04 and C47 53 085 04 Force vs stroke curve Powered with nominal current Used on proportional valves for precise controlling direction, pressure and flow. Push type Small hysteresis and quick response time Emergency manual override Insulation class of coil: F (H available on request) Electrical connector: 2-pin with protection contact acc. to DIN EN 175301-803 A Enclosure protection class: IP65 C47 53 087 04 C47 53 085 04 24 V Working Stroke 2.8 mm Total Stroke 6.4 mm Nominal Solenoid Force 72 N Nominal Force Hysteresis <10 N Nominal Current 0.8 A Nominal Resistance at 20 C 20.3 Ω ±5% Pressure Resistance (dyn.) max. 250 bar Ambient Temperature -10 to +50 C Other voltages on request 13 2 WET PIN SOLENOIDS
Wet pin Proportional Square Solenoid-NG6 Part No. C47 53 084 70 Force vs stroke curve Powered with nominal current Used on proportional valves for precise controlling direction, pressure and flow. Push type Small hysteresis and quick response time Emergency manual override Insulation class of coil: F (class H available on request) Electrical connector acc. to DIN EN 175301-803 A Enclosure protection class: IP65 C 47 53 084 70 9 V Working Stroke 3.0 mm Total Stroke 6.6 mm Nominal Solenoid Force 85.9 N Nominal Force Hysteresis <10 N Nominal Current 2.45 A Nominal Resistance at 20 C 2.88 Ω ±5% Pressure Resistance (dyn.) max. 250 bar Ambient Temperature -10 to +50 C Other voltages on request 14
Wet pin On/Off DC Solenoid-NG10 Part No. C66 13 043 04 Force vs stroke curve Note: Test current is 1.2A. Designed for directional hydraulic valves with wet pin Push type Small hysteresis and quick response time Mounting central thread M 27x1.5 Emergency manual override Insulation class of coil: F (class H available on request) Electrical connector acc. to DIN EN 175301-803 A Enclosure protection class: IP65 Core Tube Diameter = 31 mm C 66 13 043 04 24 V Working Stroke 3.0 mm Total Stroke 7.0 mm Nominal Solenoid Force 59 N Nominal Force Hysteresis <6 N Nominal Current 0.8 A Nominal Resistance at 20 C 21.3 Ω ±5% Pressure Resistance (dyn.) 210 bar NOTE: Coil and Core Tube can be ordered separately. 15 2 WET PIN SOLENOIDS
Coil NG10 Part No. 936 12 8XX XX Coil for On/Off Solenoid with core tube diameter = 31mm Insulation class of coil: F (class H available on request) Electrical connector acc. to DIN EN 175301-803 A Enclosure protection: IP65 936 128 11 00 936 128 77 00 9 to 205 V on request 16
Wet pin Proportional Solenoid-NG 10 Part No. C66 53 023 04 Force vs stroke curve The curve shows an average without hysteresis. The tolerance range refers to averages without hysteresis. Used on proportional valves for precise controlling direction, pressure and flow. Push type Small hysteresis and quick response time Mounting central thread M 27 1.5 Exchange of the coil without opening the hydraulic circuit Emergency manual override Insulation class of coil: F (class H available on request) Electrical connector acc. to DIN EN 175301-803 A Enclosure protection class: IP65 Force vs current curve C66 53 023 04 24 V Working Stroke 4.0 mm Total Stroke 8.8 mm Nominal Solenoid Force See F-S curve Nominal Force Hysteresis <15 N Nominal Current 1.4 A Nominal Resistance at 20 C 13.4 Ω ±5% Pressure Resistance (dyn.) 210 bar NOTE: Coil and Core Tube can be ordered separately. 17 2 WET PIN SOLENOIDS
WET PIN PROPORTIONAL SQUARE SOLENOID NG 10 Part No. Type 462 XXX Force vs stroke curve Wet-pin Proportional Square Solenoid NG 10 for control of position, pressure and flow. Push type version, small hysteresis and quick response timecoil Insulation class H DIN EN 175301-803A class of protection IP67 and IP6K9 Different voltages, electrical interface and pressure resistances on demand Type 462 XXX 9 to 32 V Working Stroke 4.0 mm Total Stroke 8 to 9 mm Nominal Solenoid Force 50 N Nominal Force Hysteresis ±6% Nominal Current 2.0 A Nominal Resistance at 20 C 2.75 Ω ±5% Pressure Resistance 50 (max. 130) bar Ambient Temperature -10 to +50 C Fluid Temperature (max.) 120 C 18
Proportional Solenoid with LVDT-NG 10 Part No. C 66 53 025 04 Voltage vs stroke curve Note: Test current is 1.2 A. Used in electrical-hydraulic proportional close-loop systems. LVDT detects the position of armature, the deviation of position of armature will be sent to proportional amplifier and the position of armature and spool can be precisely controlled. Small hysteresis and quick response time Insulation class of coil: F (class H available on request) Electrical connector acc. to DIN EN 175301-803 A + M12 (LVDT) Enclosure protection class: IP65 Force vs STROKE curve Force vs current curve of proportional solenoid C66 53 025 04 24 V Working Stroke 4.0 mm Total Stroke 8.8 mm Nominal Solenoid Force See F-S curve Nominal Force Hysteresis <15 N Nominal Current 1.4 A Nominal Resistance at 20 C 13.4 Ω ±5% Pressure Resistance (dyn.) 210 bar of LVDT C66 53 025 04 Supply Voltage 24 V ±20% Output Voltage linear Range 12 to 3 V Measurement Range ±4 mm Gain 1.125 V/mm ±3% Offset Range (typ.) ±1 mm Linearity (max.) ±1.5 % Temperature Drift Gain 200 ppm/ C Working Temperature -20 to +100 C 19 2 WET PIN SOLENOIDS
20
Linear variable differential transformers (LVDT) Part No. F00 11 269 04, F00 11 268 41 CURRENT stroke curve F00 11 268 41 LVDT is widely used in test systems, weighing systems and hydraulic control systems, etc. LVDT can convert the linear motion of an object into a corresponding electrical signal. A complete control system can be realized by LVDT, control electronics and a proportional solenoid. Excellent linearity and gain Long service life Withstand high pressure M12 Connector VOLTAGE stroke curve F00 11 269 04 F00 11 269 04 F00 11 268 41 Supply Voltage 24 V ±20% 15 V ±5% Output Current 2 to 10 ma 4 to 20 ma Output Load Impedance min. 10 KΩ 100 Ω Gain 0.25 V/mm ±3% 0.5 ma/mm Operating Stroke ±16 mm Offset Range (typ.) ±1 mm Linearity (typ.) ± 7% F.S. Temperature Drift (typ.) 0.3 %/ C Ambient Temperature 0 to +85 C Pressure Resistance (dyn.) 315 bar 21 3 DISTANCE SENSORS
Position Switch for core tubes Part No. F00 21 088 04 Used to detect the position (0/1) of hydraulic valves to ensure safety operation. Small switching point hysteresis Excellent Reproducibility High pressure endurance Wide range of operating temperature M12 Connector Characteristic curve F00 21 088 04 Supply Voltage Ub 24 V ±20% Output Voltage (min.) Ub-2.5 V Output Current (max.) 250 ma Switching Point Hysteresis (max.) 0.06 mm Reproducibility at 25 C ±0.02 mm Operating Temperature -20 to +85 C Pressure Resistance (dyn.) max. 315 bar 22
C-FRAME SOLENOID Part No. 118 XXX Small solenoids for different industrial applications. samples: Automation Industry: Ticket Stamper, Coin- and Bill-, Checkand Sorting-Machines Electrical switching units: actuators for power switches and circuit breakers Automotive: Comfort solenoid for safety belt rollup Safety Equipment: Interlocking systems for doors and windows Textile Machinery: Tread controllers, alterable switches Use of cost-effective stamp-bent parts and molded parts for yoke and bobbin Plunger bearing in plastic tube Voltage from 6 V to 230 V DC Push/pull variants, with and without return spring Electrical interface by leads, connectors and pins Class of protection IP00 TECHNICAL DATA Dimensions 100 % ED 40 % ED 25 % ED 15 % ED 5 % ED No. B (mm) H (mm) L (mm) D (mm) Stroke (mm) Force (N) Power (W) Force (N) Power (W) Force (N) Power (W) Force (N) Power (W) Force (N) Power (W) 115 14 15 20 5 5 0,05 2,3 0,1 5 0,2 8 0,3 12 1,0 37 116 16 19,5 24 7,3 5 0,2 3,2 0,6 8 0,8 11 1,2 19 3,2 60 118 18 20,5 32 8 6 0,3 4,2 0,7 10 1,1 16 1,8 26 5,3 82 107 18 21 37 7,1 7 0,3 4,6 0,6 11 0,9 18 1,4 29 3,8 84 23 4 DC SOLENOIDS
D-FRAME SOLENOID Part No. 128 XXX Small solenoids for different industrial applications. samples: Automation Industry: Ticket Stamper, Coin- and Bill-, Checkand Sorting-Machines Electrical switching units: actuators for power switches and circuit breakers Automotive: Comfort solenoid for safety belt rollup Safety Equipment: Interlocking systems for doors and windows Textile Machinery: Tread controllers, alterable switches Use of cost-effective stamp-bent parts and molded parts for yoke and bobbin Plunger bearing in plastic tube Voltage from 6 V to 230 V DC Push/pull variants, with and without return spring Electrical interface by leads, connectors and pins Class of protection IP00 TECHNICAL DATA Dimensions 100 % ED 40 % ED 25 % ED 15 % ED 5 % ED No. B (mm) H (mm) L (mm) D (mm) Stroke (mm) Force (N) Power (W) Force (N) Power (W) Force (N) Power (W) Force (N) Power (W) Force (N) Power (W) 113 13 11 45 5 6 0,1 4 0,3 9 0,4 14 1 19 1 54 197 24 30 30 10 6 0,5 5 1,1 12 1,7 19 3 32 10 109 131 24 27 42 9,3 10 0,3 6 0,8 15 1,2 23 2 36 5 102 130 24 29 40 9,3 10 0,4 6 0,8 13 1,3 20 2 30 6 105 142 30 32 40 9,4 10 0,4 7 1,3 16 1,9 24 3 40 9 117 133 26 32 59 12 12 1,4 10 3,2 23 4,9 36 8 60 20 169 136 36 38 44 15 10 2,2 10 4,8 21 6,5 34 12 54 32 185 137 36 38 52 15 15 1,2 11 2,5 24 4,1 40 6 63 17 185 138 36 38 64 15 20 1,0 11 2,5 28 3,5 45 6 70 14 193 148 41 48 47 16 15 2,0 12 4,5 27 7,0 43 11 66 26 184 150 49 50 100 15 30 2,5 22 5 45 8,5 75 12 104 31 417 24
PUSH/PULL DC SOLENOID, CLOSED TYPE Part No. 2XX XXX Solenoids for different industrial applications with high power demand - application samples: Big Diesel Engines: Stop-Actuator, controller for Common Rail Pumps Textile Industry Machines Membrane Pumps High magnetic power Long life, maintenance free bearings Voltage from 6 to 230 V DC Push/pull variants, with and without return spring Electrical interface by leads, connectors and pins Class of protection from IP00 to IP65 possible TECHNICAL DATA Dimensions 100 % ED 40 % ED 25 % ED 15 % ED 5 % ED No. D (mm) L (mm) Stroke (mm) Force (N) Power (W) Force (N) Power (W) Force (N) Power (W) Force (N) Power (W) Force (N) Power (W) 220 20 37 3 2 5 4 11 5 16 6 27 9,5 78,5 232 32 41 5 5 8 10 18 14 30 18 50 30 125 236 36 40 6 5 8 9 18 12 31 16 52 28 128 238 38 57 8 8 12 16 27 21 41 40 70 38 191 248 48 71 10 14 17 29 39 38 62 50 102 80 279 255 55 80 13 18 22 36 57 45 84 64 146 108 396 270 70 85 15 30 29 59 65 81 102 112 181 195 477 280 80 110 20 40 40 87 92 118 140 172 240 285 660 290 90 141 25 70 44 115 95 155 152 210 273 350 780 25 4 DC SOLENOIDS
PRESSURE SENSOR Part No. Type S400 Pressure sensor used for gaseous media for integration into circuit boards in industrial applications Customizable pressure range from 0.1 to 40 bar for soldering, direct board or frame mounting For relative or absolute pressure application Pressure port contour and electrical pins upon customer requirement Absolute version for direct embedding into molded housing Designed for highest EMC requirements TECHNICAL DATA S400 Nominal Pressure 0.1 to 40 bar Pressure Relative or absolute Burst Pressure 3x nominal pressure Supply Voltage 5 V or 8 to 30 V Accuracy (-20 to 100 C) ±1.0% Operating Temperature -40 to +140 C Protection Class IP00 Electrical Solutions Soldering pins, flex strips, contact plugs or others 5 Pressure sensors 26
PRESSURE SENSOR Part No. Type E3 Pressure sensor for liquid or gaseous media in mobile applications and bayonet nut connector. Customized pressure range from 0.1 to 40 bar with individual pressure ports For relative or absolute pressure applications and supply voltage 5 V or 8 to 30 Volt Operation temperature up to 140 C possible Protection class IP67 or IP6K9K Pressure port contour upon customer requirement Technische TECHNICAL DATA Daten Type E3 Nominal Pressure 0.1 to 40 bar Pressure Relative or absolute Burst Pressure 3x nominal pressure Supply Voltage 5 V or 8 to 30 V Accuracy (-20 to 100 C) ±1,0% Operating Temperature -40 to +140 C Electrical Connector Bayonet nut according DIN 72585 Pressure Port M10x1.5 to M16x1.5, 1/4 und 1/8 NPTF 27 5 Pressure sensors
INDIVIDUAl PRODUCTS The products shown on the previous pages represent only a very small part of our product range. We are glad to develop individually designed and customized products according to your specifications. Our portfolio for customer-specific products includes: SPEED SENSORS (passive/inductive and active) PNEUMATIC AND FLUID PRESSURE SENSORS Hydraulic, Pneumatic and Mechanical Solenoids of all variations 6 INDIVIDUAL PRODUCTS 28
ETO MAGNETIC GmbH Hardtring 8 78333 Stockach GERMANY EKS Elektromagnetik GmbH Steinbeisstraße 50 71665 Vaihingen/Enz GERMANY ETO SENSORIC GmbH Löffelholzstraße 20 90441 Nürnberg GERMANY ETO MAGNETIC CORP. 4311 Patterson S. E. Grand Rapids, MI 49512 USA ETO MAGNETIC Sp. z o.o. ul. Eugeniusza Kwiatkowskiego 7 52-407 Wrocław POLAND ETO MAGNETIC TECHNOLOGIES (Kunshan) Co., Ltd. Nr. 8, Guzheng Road 215300 Kunshan CHINA www.etogroup.com