Table of Contents M Series Variable Displacement Piston Pumps Introduction.... 3 Hydraulic System Design Calculations.... 4 Model Code Selection.... 5 Model Code Options.... 6 Specifications and Performance... 8 Control Options.... 11 Performance Industrial PVM18.... 15 PVM2.... 2 PVM45.... 25 PVM5.... 3 PVM57.... 35 PVM63.... 4 PVM74.... 45 PVM81.... 5 PVM98.... 55 PVM16.... 6 PVM131.... 65 PVM141.... 7 Dimensions PVM18/2... 75 PVM45/5... 82 PVM57/63... 89 PVM74/81... 94 PVM98/16... 98 PVM131/141... 12 Mounting Flange Options.... 17 Shaft Options.... 18 Shaft Selection Data.... 111 Port Options.... 112 Operating Requirements and Recommendations.... 114 Installation and Start-up.... 115 2 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Introduction Eaton M Series pumps are open circuit, axial piston designs. A variety of control options allows the pumps to perform most efficiently in a specific application. Efficiency of the pump controls allows down-sizing of system cooling needs, saving up front cost in the machine. Alternatively, cooling capacity could be kept the same and the flow capability of the system increased, thus improving performance and customer satisfaction. The M Series also contains a strong proven rotating group allowing the pumps to handle pressures to 315 (4568 continuous with less maintenance cost. High-load bearings and a stiff drive shaft help provide a pump life of 8 hours at rated industrial conditions, reducing operating costs and extending operating life. M Series pumps feature a saddle-type yoke with steel-backed polymer bearings. The stiff yoke reduces deflection and allows even loading of bearings, improving life. A single control piston reduces loading on the yoke, resulting in reduced pump size which allows installation in tighter locations. M Series pumps operate at a level of quietness that exceeds the requirements of today s demanding work conditions. The pumps feature a unique threepiece envelope (flange, housing and valve block) specifically created for low fluid-borne and structure-borne noise levels. Another pump feature a bimetal timing plate improves pump filling characteristics which, in turn, reduce fluid-borne noise and extend pump life. M Series pumps reduce, or in some cases remove, the need for damping riers between the noise source and the operator. This saves money on the installed cost of the system while improving customer comfort. An adjustable maximum stop provides a means of tuning flow to your system, while gauge ports allow monitoring of inlet and outlet conditions. These standard features reduce system complexity and cost. Mounting flanges are offered in SAE and ISO config urations, and ports are offered in SAE, ISO, and BSPP in both tube and flange versions. This provides a wide variety of installation opportunities for global machine design. Side- or end-ported models are available to facilitate plumbing and help fit the pump to your machine space needs. Multiple drain ports allow many mounting orientations, reducing installed costs. M Series pumps are capable of operating with many types of hydraulic fluids used in industrial systems. High-water-content and phosphate ester fluids can be accommodated, in addition to the typical petroleum based and synthetic fluids. Typical Applications Mining machinery Injection molding machines Metal forming machines Oil and Gas Equipment Conveyor lines Primary metals Metal cutting equipment Features and Benefits Long pump life Quiet pump operation Inlet and outlet gauge ports and adjustable maximum displacement stops standards Astonishingly low 4% pressure ripple Low installed and operating costs Reduced maintenance Flexibility in machine design Design promotes leak-free system 3 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Hydraulic System Design Calculations Basic Formulas Output Flow (Q) lpm = cm 3 /r x rpm gpm = in 3 /r x rpm 1 231 Power (P) kw = l/min x hp = gpm x psi 6 1714 Shaft Torque (M) N-m = x cm 3 /r lb-in = psi x in 3 /r 62.8 6.28 Shaft Speed (n) Efficiencies Volumetric Nv = gpm actual gpm theorectical Mechanical Nm = lb-in actual lb-in theorectical Total Nt = Nv x Nm Q n P M p rpm = 1 x 1/min = 231 x gpm cm 3 /r in 3 /r Output Power (P) kw = N-m x hp = lb-in x rpm 9549 63,25 Volumetric Displacement cm 3 /r = in lpm 3 /r = x 1 rpm gpm x 231 rpm Basic Formulas = 1 Newtons/cm 2 gpm = gallons per minute hp = horsepower lb-in = pound inch lb-ft = pound feet kw = kilowatt kgf = kilograms force l/min = liters per minute N-m = Newton meters psi = pounds per square inch rpm = revolutions per minute Commonly Used Conversions To Convert Into Multiply by psi 14.5 cm 3 in 3.612 C F ( C x 1.8) +32 gallons (US) liters 3.785 kg lbs 2.25 kgf/cm 2 psi 14.2 kw hp 1.341 liters US Gallons.2642 mm inches.3937 N-m lb-in 8.85 N-m lb-ft.7375 F C ( F-32)/1.8 hp kw.7457 inch mm 2.54 in 3 cm 3 16.39 lb-in N-m.113 lb-ft N-m 1.356 lbs kg.4535 psi.6896 psi kgf/cm 2.737 Note: Performance charts can be found on subsequent pages. EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 4
Model Code Selection PVM 45 E R 1 A E 1 AA A 28 A A 1, 2, 3 4, 5, 6 7 8 9, 1 11 12 13, 14 15, 16 17 18, 19 2, 21 22, 23 24 25 26 27 28 1, 2, 3 Product Series PVM M Series Variable Piston Pump 4, 5, 6 Displacement Twelve displacements available 23 and 315 continuous ratings 7 Valve Plate E - Quiet version, optimized for 1-18 rpm M - Higher speed version ref speed performance data for individual dispalcements 8 Rotation R Clockwise (Righthand) L* Counter-clockwise (Lefthand) 9, 1 Shaft Standard SAE and ISO splined versions (Other configurations optional) 11 Mounting Flange Thirteen options in SAE and ISO mounts 12 Main Port Location E** End Ported S**** Side Ported 13, 14 Main Port Type SAE & ISO tube ports and 4-bolt flange (Other configurations optional) 15, 16 Pump Special Features None AA Adjustable Maximum Displacement Stop and single shaft (standard) AB Double Shaft Seal, Two Way 17 Control None A Pressure Compensator B Pressure and Flow Compensator with Bleed Orifice C Pressure and Flow Compensator with Plugged Orifice E Industrial/Remote (57cc through 141 cc only) L - Power Control with Load Sense and Pressure compensator with Plugged Orifice (74,81 cc only, other displacements 57 cc through 141cc under development) 18, 19 Pressure Compensator Setting None 7 7 (Adjustable between 4 and 13 ) 23 23 (Adjustable between 13 and 32 ) 28 28 (Adjustable between 13 and 32 ) 2, 21 Flow Compensator Setting None 11 11 setting 2 2-2 setting 24 24-24 setting 22, 23 Power control Torque Limiter Setting None 5-5% of rated torque* (adjustable from 2-9% of rated torque,*for any other values specify % of rated torque ) 24 Compensator Special Features None 25 Auxiliary Mounting Pad *** None (Auxiliary mounting available on all frame sizes) 26 Paint No Paint A Standard Blue Paint 27 Customer Identification None (Contact Eaton for Options) 28 Design Code A A (Initial Release) * Not available on 74, 81, 98 and 16 End Port ** Not available on 74, 81, 98 and 16 LH *** Through drive not available on the LH **** Not available on 18 5 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Model Code Options 4,5,6 Maximum Geometric Displacement Displacement Code 18 2 45 5 57 63 74 81 98 16 131 141 cm 3 /r 18, 21,1 45,1 5, 57,4 63,1 73,7 81, 98,3 16,5 131,1 141, in 3 /r 1.1 1.29 2.75 3.5 3.5 3.85 4.5 4.94 6. 6.5 8. 8.6 9,1 Shaft-End Type at Electric Motor End Shaft Code Description PVM18/2 PVM45/5 PVM57/63 PVM74/81 PVM98/16 PVM131/141 SAE, SAE A, Straight Keyed 1 SAE, SAE 19-1, Straight Keyed 2 SAE, SAE A, 9T Spline 3 SAE, SAE A, 11T Spline 4 SAE, SAE B, Straight Keyed 5 5 SAE, SAE B-B, Straight Keyed 6 6 6 SAE, SAE B, 13T Spline 7 7 7 SAE, SAE B-B, 15T Spline 8 8 8 SAE, SAE C, Straight Keyed 9 9 9 9 SAE, SAE C-C, Straight Keyed 1 1 1 SAE, SAE C, 14T Spline 11 11 11 11 SAE, SAE C-C, 17T Spline 12 12 12 SAE, SAE D, Straight Keyed 13 SAE, SAE D, 13T Spline 14 ISO E2N, Straight Keyed 15 ISO E25N, Straight Keyed, Short Spigot 16 ISO E25N, Straight Keyed 17 17 17 ISO E32N, Straight Keyed, Short Spigot 18 18 18 18 ISO E4N, Straight Keyed, Short Spigot 19 19 19 11 Mounting Flange Specifications Code Description PVM18/2 PVM45/5 PVM57/63 PVM74/81 PVM98/16 PVM131/141 A SAE A, 2-bolt B ISO 8A2HW C SAE B, 2-bolt D ISO 1A2HW E SAE C, 2-bolt F ISO 125-A2HW G SAE C, 4-bolt H ISO 125B4HW J SAE D, 4-bolt K ISO 16B4HW = Available = Not Available EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 6
Model Code Options 13,14 Main Port Options Inlet Code Description Outlet PVM18/2 PVM45/5 PVM57/63 PVM74/81 PVM98/16 PVM131/141 Inlet 2 24 24 1 SAE J1926 (End ports only) Tube Ports Outlet 12 16 16 (End ports only) 2 SAE J518 Inlet 1.25 inch 2. inch 2. inch 2. inch 2.5 inch 2.5 inch Flange Ports Outlet.75 inch 1. inch 1. inch 1. inch 1. inch 1.25 inch* Inlet M42 M48 M48 3 ISO 6149-1 (End ports only) Tube Ports Outlet M27 M33 M33 (End ports only) 4 ISO 6162 Inlet 32mm 51mm 51mm 51mm 64mm 64mm Flange Ports Outlet 19mm 25mm 25mm 25mm 25mm 32mm* British Standard 5 Parallel Pipe Inlet G 1-1/4 G 1-1/2 Tube Ports Outlet G 3/4 G 1 *SAE Code 62, high pressure series, or ISO 4. Other flange ports are SAE Code 61, standard pressure series, or ISO 25-35. 25 Thru-Drive Options Code Description PVM18/2 PVM45/5 PVM57/63 PVM74/81* PVM98/16 PVM131/141 O Single pump, non-thru-drive A SAE A, 2-bolt, 9T spline B SAE A, 2-bolt, 11T spline C SAE B, 2-/4-bolt, 13T spline D SAE B-B, 2-/4-bolt, 15T spline E SAE C, 2-/4-bolt, 14T spline F SAE C-C, 2-/4-bolt, 17T spline G ISO 8-A2HW, 9T SAE spline H ISO 8-A2HW, 11T SAE spline J ISO 1-A2/B4HW, 13T SAE spline K ISO 1-A2/B4HW, 15T SAE spline L ISO 125-A2/B4HW, 14T SAE spline M ISO 125-A2/B4HW, 17T SAE spline = Available = Not Available * Not available on the 74/81 LH 7 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Specifications and Performance Quiet version, optimized for 1-18 rpm (E) Displacement, Pressure and Flow Ratings At 5 C (12 F), SAE 1W oil, 1 absolute ( psig) inlet Maximum Maximum Flow at 28 (4 * Geometric Maximum Pressure ( l/min (USgpm) Average measured flow rate Displacement @18 @15 @12 @1 Model Series cm /r (in /r) 3 3 Nominal Peak** r/min r/min r/min r/min PVM18 18 (1.1) 315 (4568) 35 (5) 31 (8.2) 26 (7) 21 (5.5) 17 (4.5) PVM2 21,1 (1.29) 23 (33) 28 (4) 35 (9) 29 (8) 23 (6) 19 (5) PVM45 45,1 (2.75) 315 (4568) 35 (5) 76 (2) 65 (17) 49 (13) 42 (11) PVM5 5, (3.5) 23 (33) 28 (4) 87 (23) 75 (2) 62 (16) 49 (13) PVM57 57,4 (3.5) 315 (4568) 35 (5) 12 (27) 85 (22.4) 66 (17.4) 54 (14.3) PVM63 63,1 (3.85) 23 (33) 28 (4) 111 (29) 93 (24) 74 (19) 6 (16) PVM74 73,7 (4.5) 315 (4568) 35 (5) 127 (33.5) 16 (28) 86 (22.7) 7 (18.5) PVM81 81, (4.94) 23 (33) 28 (4) 139 (37) 116 (31) 93 (25) 76 (2) PVM98 98,3 (6.) 315 (4568) 35 (5) 17 (45) 141 (37) 112 (29.6) 92 (24.3) PVM16 16,5 (6.5) 23 (33) 28 (4) 187 (49) 155 (41) 123 (32) 12 (27) PVM131 131,1 (8.) 315 (4568) 35 (5) 215 (57) 178 (47) 141 (37) 118 (31) PVM141 141, (8.6) 23 (33) 28 (4) 238 (63) 199 (53) 158 (42) 131 (35) **Momentary system pressure spikes only. Speed, Power and Torque Ratings At 5 C (12 F), SAE 1W oil, 1 absolute ( psig) inlet Maximum Maximum Torque at Operating 28 Approximate Model Speed Maximum Power at 28 (4 kw (hp)*@88% M.E. (4 * Weight Series r/min @18 r/min @15 r/min @12 r/min @ 1 r/min Nm (lb-ft) kg (lb) PVM18 18 16 (22) 13 (18) 11 (15) 9 (12) 84 (62) 15 (33) PVM2 18 14 (18) 11 (15) 9 (12) 8 (1) 73 (54) 15 (33) PVM45 18 41 (55) 34 (46) 27 (37) 23 (31) 221 (163) 24 (52) PVM5 18 35 (47) 3 (4) 28 (38) 23 (31) 19 (14) 24 (52) PVM57 18 52 (7) 44 (59) 36 (49) 29 (39) 272 (21) 36 (79) PVM63 18 42 (57) 36 (48) 29 (39) 24 (32) 228 (168) 36 (79) PVM74 18 63 (84) 52 (7) 42 (56) 35 (47) 334 (246) 45 (99) PVM81 18 56 (75) 46 (62) 35 (47) 28 (37) 286 (211) 45 (99) PVM98 18 88 (118) 72 (97) 58 (78) 48 (64) 464 (342) 55 (121) PVM16 18 72 (97) 6 (8) 48 (64) 4 (54) 383 (282) 55 (121) PVM131 18 113 (152) 94 (126) 75 (11) 63 (85) 596 (44) 66 (145) PVM141 18 94 (126) 79 (16) 63 (85) 53 (71) 497 (367) 66 (145) Standard Response Times* Model Series On Stroke (msec) Off Stroke (msec) PVM18 3 25 PVM2 39 26 PVM45 14 4 PVM5 14 4 PVM57 65 2 PVM63 85 2 * 33 psi on overbore pumps Standard Response Times* Model Series On Stroke (msec) Off Stroke (msec) PVM74 85 3 PVM81 85 3 PVM98 65 25 PVM16 72 29 PVM131 135 3 PVM141 1 3 *Values with pressure compensator control. EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 8
Specifications and Performance Higher speed version (M) Displacement, Pressure and Flow Ratings At 93 C (2 F), SAE 1W oil, 1 absolute ( psig) inlet Geometric Maximum Pressure ( Maximum Flow at 28 (4 Displacement Flange Ports Tube Ports Model Series cm 3 /r (in 3 /r) Nominal Peak** l/min (USgpm) @ 1 inlet l/min (USgpm) @ 1 inlet PVM18 18, (1.1) 315 (4568) 35 (5) 46 (12) @ 28 r/min 46 (12) @ 28 r/min PVM2 2,1 (1.22) 23 (33) 28 (4) 53 (14) @ 28 r/min 53 (14) @ 28 r/min PVM45 45,1 (2.75) 315 (4568) 35 (5) 115 (3) @ 26 r/min 16 (28) @ 24 r/min PVM5 5, (3.5) 23 (33) 28 (4) 125 (33) @ 26 r/min 116 (31) @ 24 r/min PVM57 57,4 (3.5) 315 (4568) 35 (5) 14 (37) @ 25 r/min 128 (34) @ 23 r/min PVM63 63,1 (3.85) 23 (33) 28 (4) 15 (4) @ 25 r/min 14 (37) @ 24 r/min PVM74 73,7 (4.5) 315 (4568) 35 (5) 163 (43) @ 24 r/min PVM81 81, (4.94) 23 (33) 28 (4) 181 (48) @ 24 r/min PVM98 98,3 (6.) 315 (4568) 35 (5) 2 (53) @ 22 r/min PVM16 16,5 (6.5) 23 (33) 28 (4) 222 (59) @ 22 r/min PVM131 131,1 (8.) 315 (4568) 35 (5) 233 (62) @ 2 r/min PVM141 141, (8.6) 23 (33) 28 (4) 258 (68) @ 2 r/min **Less than.5 second. Standard Response Times* Model Series On Stroke (msec) Off Stroke (msec) PVM18 5 2 PVM2 57 22 PVM45 14 4 PVM5 14 23 PVM57 65 2 PVM63 94 2 Standard Response Times* Model Series On Stroke (msec) Off Stroke (msec) PVM74 95 3 PVM81 135 3 PVM98 85 24 PVM16 9 25 PVM131 1 3 PVM141 128 28 *Values with pressure compensator control. 9 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Specifications and Performance Higher speed version (M) Speed, Power and Torque Ratings At 93 C (2 F), SAE 1W oil, 1 absolute ( psig) inlet Operating Speed and Pressure r/min Max. Power at Max. Torque at Approximate 1 Inlet,85 Inlet Max. Speed and 28 28 (4 Weight (dry) Model Series Flange Ports Tube Ports Flange Ports (4 kw (hp) Nm (lb-ft) kg (lbs) 28 r/min 24 (32) PVM18 28 r/min 24 (32) 82 (6) 15 (33) 26 r/min 22 (3) 28 r/min 21 (28) PVM2 28 r/min 21 (28) 72 (53) 15 (33) 26 r/min 2 (27) 26 r/min 56 (75) PVM45 24 r/min 53 (71) 198 (46) 24 (52) 22 r/min 48 (64) 26 r/min 51 (68) PVM5 24 r/min 48 (64) 24 (15) 24 (52) 22 r/min 44 (59) 25 r/min 68 (91) PVM57 23 r/min 62 (83) 262 (193) 36 (79) 21 r/min 56 (75) 25 r/min 59 (79) PVM63 24 r/min 57 (76) 225 (166) 36 (79) 22 r/min 52 (69) PVM74 24 r/min 84 (113) 19 r/min 69 (93) 334 (246) 45 (99) PVM81 24 r/min 69 (93) 19 r/min 55 (74) 276 (24) 45 (99) PVM98 22 r/min 15 (141) 18 r/min 86 (115) 457 (337) 55 (121) PVM16 22 r/min 87 (117) 18 r/min 7 (94) 377 (278) 55 (121) PVM131 2 r/min 122 (164) 16 r/min 98 (131) 581 (429) 66 (145) PVM141 2 r/min 12 (137) 16 r/min 81 (19) 483 (356) 66 (145) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 1
Specifications and Performance Variable Speed Drive Variable Speed Performance- System Pressure vs Speed Model Max Speed Max Speed Min Speed Nominal Peak Inertia Series E * (rpm) M *(rpm) (rpm) Pressure () Pressure ()** (kg-cm2) PVM18 18 28 315 35 11.8 PVM2 18 28 23 28 11.8 PVM45 18 26 315 35 36.2 PVM5 18 26 23 28 33.9 PVM57 18 25 315 35 51.6 PVM63 18 25 23 28 5.5 PVM74 18 24 315 35 78.1 PVM81 18 24 23 28 72.7 PVM98 18 22 315 35 131.6 PVM16 18 22 23 28 122.7 PVM131 18 2 315 35 213.5 PVM141 18 2 23 28 29.7 * Valve plate type **Less than.5 second. 35 PVM System Pressure vs. Shaft Speed System Pressure () 3 25 2 15 1 315 (standard-bore displacements) - PVM18, 45, 57, 74, 98, 131 (max speed varies by displacement) 23 (over-bore displacements) - PVM2, 5, 63, 81, 16, 141 (max speed varies by displacement) 5 Max Speed Rating: 1. Standard speed version "E" - Optimzed for low sound, 18 for all displacements 2. High speed version "M" - up to 28 depending on displacement. See spec for details. 2 4 6 8 1 12 14 16 18 2 22 24 26 28 Shaft Speed (rpm) Test condition: Mineral oil SAE 1W, oil temperature 49º C (12º F), 1 absolute inlet pressure. 11 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Control Options Pressure Compensator Control Code A The pump will provide a continuously modulated flow to meet changing load demands at a pre-adjusted compensator pressure. At pressures below the compensator setting, the pump will operate at maximum displacement. See model code on page 4 for compensator pressure ranges. Warning: The pressure compensator may be adjusted beyond the rated pressure of the pump. When adjusting the pressure limiter, install a -35 (-5 gage in the outlet gage port and limit the pressure setting to the continuous rated pressure for the pump displacement shown on page 7. ssure Cut-off Characteristics of e A Pressure Compensator Control C (12F), 18 r/min, static conditions Outlet Flow Q Industrial Pressure Cut-off Change in Characteristics of Code A Pressure A Pressure Compensator Control at 5 C (12 F), static conditions. Change in Flow B F case drain K inlet gage port K outlet gage port Pressure Cut-off Characteristics of Code A Pressure Compensator Control @ 5 C (12 F), 18 r/min, static conditions Outlet Flow Change in Pressure A Outlet Pressure P B inlet To load Change in Flow B B inlet See model code on page xx for spring (pressure) adjustment ranges. F case drain C outlet K inlet gage port K outlet gage port To load See model code on pag spring (pressure) adjust C outlet Outlet Pressure P Pressure Cut-off Characteristics of Pressure Compensator Control @ 5 C (12 F), Static Conditions P Outlet Max. Speed Q Outlet Flow Pressure A B Model Series r/min l/min (USgpm) ( ( L/min (USgpm) PVM18 18 32 (8.5) 315 (4568) 2,8 (4) 4,5 (1.2) PVM2 18 35 (9.25) 23 (33) 2,8 (4) 4,5 (1.2) PVM45 18 76 (2) 315 (4568) 1 (15) 4,5 (1.2) PVM5 18 87 (23) 23 (33) 1 (15) 4,5 (1.2) PVM57 18 12 (27) 315 (4568) 3,5 (51) 14 (3.7) PVM63 18 113 (29) 23 (33) 7,4 (17) 7,6 (2.) PVM74 18 127 (33.5) 315 (4568) 1,5 (22) 37 (9.8) PVM81 18 141 (37) 23 (33) 1,5 (22) 37 (9.8) PVM98 18 179 (47) 315 (4568) 1,5 (22) 25 (6.6) PVM16 18 195 (51.5) 23 (33) 1,5 (22) 2 (5.3) PVM131 18 229 (6.5) 315 (4568) 3,5 (51) 19 (5.) PVM141 18 238 (63) 23 (33) 3,5 (51) 14 (3.7) 12 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Control Options K outlet gage port + åå To load C outlet Mobil Pressure Cut-off Characteristics of Pressure Compensator Control at 93 C (2 F), static conditions. Q Change in Pressure A Change in Flow B Outlet Flow Outlet Pressure P Pressure Cut-off Characteristics of Pressure Compensator Control @ 93 C (2 F), Static Conditions P Outlet Rated Speed Q Outlet Flow Pressure A B Model Series r/min l/min (USgpm) ( ( L/min (USgpm) PVM18 28 42 (11) 315 (4568) 2,8 (4) 4,5 (1.2) PVM2 28 52 (14) 23 (33) 2,8 (41) 4,5 (1.2) PVM45 26 115 (3) 315 (4568) 1 (15) 4,5 (1.2) PVM5 26 125 (33) 23 (33) 1 (15) 4,5 (1.2) PVM57 25 14 (37) 315 (4568) 3,5 (5) 14 (3.7) PVM63 25 159 (42) 23 (33) 7,4 (17) 11,4 (3.) PVM74 24 174 (46) 315 (4568) 1,5 (2) 37 (9.8) PVM81 24 185 (49) 23 (33) 1,5 (22) 37 (9.8) PVM98 22 217 (57) 315 (4568) 1,5 (2) 32 (8.4) PVM16 22 234 (62) 23 (33) 1,5 (22) 24 (6.33) PVM131 2 253 (67) 315 (4568) 1, (15) 23 (6.) PVM141 2 258 (68) 23 (33) 7, (1) 14 (3.7) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 13
Control Options Load Sensing and Pressure Compensator Control Code B or C The pump will provide power matching of pump output to system load demand, maximizing efficiency and improving load metering characteristics of any directional control valve installed between the pump and the load. Load sensing ensures that the pump always provides only the amount of flow needed by the load. At the same time, the pump operating pressure adjusts to the actual load pressure plus a pressure differential required for the control action. When the system is not demanding power, the load sense control will operate in an energy-saving stand-by mode. Typically, the differential pressure is that between the pressure inlet and service port of a proportionally controlled directional valve, or a load sensing directional control valve. See the model code on page 4 for differential pressure settings for load sensing. If the load pressure exceeds the system pressure setting, the pressure compensator de-strokes the pump. The load sensing line must be as short as possible and can also be used for remote control or unloading of the pump pressure. For remote control purposes, it is recommended that you contact your Eaton representative for the correct configuration of the control. Warning: The pressure compensator may be adjusted beyond the rated pressure of the pump. When adjusting the pressure limiter, install a -35 (-5 gage in the outlet gage port and limit the pressure setting to the continuous rated pressure for the pump displacement shown on page 7. F case drain K inlet gage port K outlet gage port Optional bleed-down orifice in Code B control.,4 mm (.16 in.) Orifice is plugged for no bleed down in control Code C. B inlet To load C outlet J load sense signal port 14 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Control Options Industrial Control Compensator Code E & F (Model 57-141 only) This pump is intended for use when multiple, remote, or electronically controlled compensating settings, with or without load sensing, are desired. Pressure compensation is obtained when an internal plug is removed, the load-sense signal port is kept plugged, and internal pilot pressure is applied to the spring chamber of the control spool. For pressure compensation with load sensing, the internal plug stays, the load-sense signal port is unplugged, and pilot pressure is externally applied. An external relief valve (not supplied) controls spring chamber pressure. The externally adjustable spring determines the differential pressure setting of the control. Outlet pressure is limited to the valve of the spring chamber (pressure port) pressure, plus control differential pressure. Spring chamber (pilot) pressure is separated from outlet pressure by an internal orifice. Outlet pressure shifts the spool when pressure drop across the orifice reaches the differential pressure setting, and the pump de-strokes. The relief valve can be mounted to an NFPA-D3/ISO 441-3 pad on the pump control, or remotely located via tapping and blanking plates installed on the pad. See Ordering Procedure, page 27, for more on valves and plates. The standard factory-set differential pressure setting of the pump control is 2 (29 and is not specified in the pump model number. Any other ordered differential pressure, within the control s adjustable pressure range of 17-35 (247-58, will be specified in the model number. With Pressure & Flow Compensator (E) Inlet Inlet To load Inlet Outlet Load sense signal port To load Pressure Compensating Without Load Sensing (F) Inlet To load To load Outlet Outlet Outlet Load sense signal port Load sense signal port Load sense signal port Pressure port Tank port Pressure port Tank port Pressure port Tank port Pressure port Tank port Case drain Case drain Case drain Case drain EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 15
Control Options Power Control-Code L The Power control limits the maximum torque output by the piston pump by reducing the displacement as pressure increases hence limiting the power rating at a given speed. As pressure increases the pump displacement is reduced such that the set torque value is not exceeded. The torque can be set between 2-9% of rated torque for given displacement at 18 rpm (model code pos 22-23, ref table below for range of torque. Warning: The pressure compensator may be adjusted beyond the rated pressure of the pump.when adjusting the pressure limiter, install a -35 (-5 gage in the outlet gage port and limit the pressure setting to the continuous rated pressure for the pump displacement shown on page 7. Displacement (1/ Dmax) Displacement (1/Dmax) 1.2 1.8.6.4.2 Flow Vs Pressure 9% 85% 65% 5% 35% 2% Torque(1/Tmax) Torque (1/Tmax) 1..8.6.4.2 Torque Vs Pressure ` 9% 85% 65% 5% 35% 2%.2.4.6.8 1 (1/ Pressure (1/Pmax)..2.4.6.8 1 Pressure (1/ (1/Pmax) Characteristics of Code L Power Control at 5 C (12 F), static conditions. Torque setting range by displacemnent Displacement (cc) Rated Torque Min torque setting Max torque setting lb-in (N-m) lb-in (N-m), 2% lb-in (N-m), 9% of rated torque* of rated torque 74 292 (33) 584 (66) 2628 (297) 81 2626 (297) 525 (59) 2363 (267) * for Minimum torque setting (2%) the pump may not deliver the flow at higher pressure. Please contact Eaton Engineering for flow generated at max pressure EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 16
Performance Quiet version, optimized for 1-18 rpm (E), PVM74/PVM81 Power Control -code L Performance curves for 74 & 81 cc with power control, at various torque setting % Pressure () 5 1 15 2 25 3 35 3 12 1 25 9% 2 8% 8 15 7% 6% 6 1 5% 4 4% 5 2% 3% 2 5 1 15 2 25 3 35 4 45 Pressure (PSI) Mineral oil SAE 1W, oil temperature 49º C (12º F), 1 absolute inlet pressure. Curves plotted at load sense delta P = 24 Flow (gpm) Flow Vs Pressure - 74cc Flow (lpm) Torque (lb - in) 3 25 2 15 1 5 Torque Vs Pressure - 74cc Pressure () 5 1 15 2 25 3 2% 9% 8% 7% 6% 5% 4% 3% 5 1 15 2 25 3 35 4 45 Pressure (PSI) Mineral oil SAE 1W, oil temperature 49º C (12º F), 1 absolute inlet pressure. Curves plotted at load sense delta P = 24 3 25 2 15 1 5 Torque (N- m) Flow (gpm) Pressure () 5 1 15 2 25 4 35 3 25 2 15 1 Flow Vs Pressure - 81cc 9% 8% 7% 6% 5% 4% 3% 5 2 2% 5 1 15 2 25 3 35 4 Pressure (PSI) Mineral oil SAE 1W, oil temperature 49º C (12º F), 1 absolute inlet pressure. Curves plotted at load sense delta P = 24 14 12 1 8 6 4 Flow (lpm) Torque (lb -in) Pressure () 5 1 15 2 25 25 9% 2 8% 7% 15 1 5 Torque Vs Pressure - 81cc Mineral oil SAE 1W, oil temperature 49º C (12º F), 1 absolute inlet pressure. Curves plotted at load sense delta P = 24 2% 6% 5% 4% 3% 5 1 15 2 25 3 35 4 Pressure (PSI) 25 2 15 1 5 Torque (N - m) 17 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Performance Industrial PVM18 Noise Level Noise dba Level dba 52 48 18 r/min min. flow 5 46 5 48 18 (7) r/min Sound pressure min. flow data equivalent to NFPA. 46 5 (7) Sound pressure data equivalent to NFPA. Noise Level Noise dba Level dba Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 66 Typical Noise Levels at 18 and 12 r/min with 64 Petroleum 18 r/min Oil (1W) at 5 C (12 F) and 1. absolute max. ( flow psi gauge) Inlet 66 62 64 6 62 58 6 56 58 54 56 52 54 5 62 6 62 58 6 56 58 54 56 52 54 5 52 48 5 46 48 44 46 42 44 42 18 r/min max. flow 12 r/min max. flow 12 r/min max. flow 1 (15) 15 (22) 2 (29) 25 (36) 3 (44) 35 (5) Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute 15 r/min ( psi gauge) Inlet 15 1 r/min max. max. flow flow 1 r/min max. flow 15 r/min min. flow 5 (7) 1 (15) 1 (15) 15 (22) 15 (22) 2 25 (29) 12 r/min (36) min. flow 15 2 (22) 1 r/min min. flow (29) 2 (29) 25 (36) 3 (44) 3 (44) 35 (5) Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet max. flow 15 r/min min. flow 5 (7) 1 (15) 1 r/min min. flow 12 r/min min. flow 25 (36) 3 (44) 35 (5) 35 (5) Efficiency % Torque Torque Nm (in-lb) Nm (in-lb) Delivery and Efficiency at 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Volumetric Delivery Efficiency and Efficiency at 18 r/min 9 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 8 Volumetric Efficiency 9 7 8 6 7 5 6 4 (11) 4 5 3 4 (8) (11) 3 4 2 (5) 2 3 (8) 3 1 1 2 (3) (5) 2 1 1 (3) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque and Power at 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 (885) Torque and Power at 18 r/min 9 (796) 5 C (12 F) and 1. absolute ( Torque, psi gauge) Inlet 1 (885) 8 (78) 9 (796) Torque, 7 (619) 8 (78) 6 (531) 7 (619) 5 (442) 6 (531) Power, 4 (354) 2 (27) 5 (442) 3 (265) Power, 15 (2) 4 (354) 2 (27) 2 (177) 3 (265) 1 (13) 15 (2) 1 (88) Torque, 5 (7) 2 (177) 1 (13) Cut-off 1 (88) 5 1 15 2 25 Torque, 3 355 (7) (7) (15) (22) (29) (36) Cut-off (44) (5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Delivery l/min (USgpm) Power Power kw (hp) kw (hp) 18 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Performance Quiet version, optimized for 1-18 rpm (E) PVM18 Torque Torque Nm (in.lb.) Nm (in.lb.) Efficiency % Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency at 15 r/min Volumetric 5 C (12 Efficiency F) and 1. absolute ( psi gauge) Inlet 1 9 Volumetric Efficiency 8 9 7 8 6 7 5 6 4 5 3 4 2 3 1 2 1 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) 5 1Outlet 15 Pressure 2 ( 25 3 (7) (15) (22) (29) (36) (44) 3 (8) 2 3 (5) (8) 1 2 (3) (5) 1 (3) 35 (5) 35 (5) Torque and Power at 15 r/min 1 (885) 5 C (12 F) and 1. absolute ( psi gauge) Inlet Torque and Power at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 9 (796) (885) 8 9 (78) (796) 7 8 (619) (78) Torque, Torque, 6 7 (531) (619) 5 6 (442) (531) 4 5 (354) (442) 3 4 (265) (354) Power, Power, 2 (27) 15 2 (2) (27) 2 3 (177) (265) 2 1 (177) (88) 1 15 (13) (2) 51 (7) (13) 1 (88) 5 (7) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 1Outlet 15 Pressure 2 ( 25 3 35 (7) (15) (22) (29) (36) (44) (5) Delivery Delivery l/min l/min (USgpm) (USgpm) Power Power kw (hp) kw (hp) Efficiency % Torque Torque Nm (in.lb.) Nm (in.lb.) Delivery and Efficiency at 12 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency at 12 r/min Volumetric 5 C (12 F) Efficiency and 1. absolute ( psi gauge) Inlet 1 9 Volumetric Efficiency 8 9 7 8 6 7 5 6 4 5 3 4 2 3 1 2 1 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) 5 1 Outlet 15 Pressure 2 ( 25 3 (7) (15) (22) (29) (36) (44) 3 (8) 2 3 (5) (8) 1 2 (3) (5) 1 (3) 35 (5) 35 (5) Torque and Power at 12 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 (885) Torque and Power at 12 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet Torque, 1 9 (796) (885) Torque, 8 9 (78) (796) 7 8 (619) (78) 6 7 (531) (619) 5 6 (442) (531) 4 5 (354) (442) 2 (27) Power, 3 4 (265) (354) 15 2 (2) (27) Power, 2 3 (177) (265) 1 15 (13) (2) 2 1 (177) (88) 51 (7) (13) 1 (88) 5 (7) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 1 Outlet 15 Pressure 2 ( 25 3 35 (7) (15) (22) (29) (36) (44) (5) Delivery Delivery l/min l/min (USgpm) (USgpm) Power Power kw (hp) kw (hp) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 19
Performance Quiet version, optimized for 1-18 rpm (E) PVM18 Efficiency % Delivery and Efficiency at 1 r/min 5 C Delivery (12 F) and and 1. Efficiency absolute at ( 1 psi gauge) r/min Inlet 1 5 C (12 F) and 1. absolute ( psi gauge) Inlet Volumetric Efficiency 1 9 Volumetric Efficiency 8 9 7 8 6 7 5 6 4 5 3 4 2 3 2 1 1 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) 5 1Outlet 15 Pressure 2 ( 25 3 (7) (15) (22) (29) (36) (44) torque torque Nm (in.lb.) Nm (in.lb.) 2 (5) 2 (5) 1 (3) 1 (3) 35 (5) 35 (5) Torque and Power at 1 r/min 5 C (12 F), Torque and 1. and Power absolute at ( 1 psi gauge) r/min Inlet 1 (885) 5 C (12 F), and 1. absolute ( psi gauge) Inlet 1 (885) 9 (796) Torque, 9 (796) Torque, 8 (78) 8 (78) 7 (619) 7 (619) 6 (531) 6 (531) 5 (442) 5 (442) 4 (354) 2 (27) 4 (354) 3 (265) 2 (27) Power, 15 (2) 3 (265) 2 (177) 2 (177) 1 (88) Power, 1 (88) 5 (7) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 1Outlet 15 Pressure 2 25 ( 3 35 (7) (15) (22) (29) (36) (44) (5) 1 15 (13) (2) 5 1 (7) (13) Delivery Delivery l/min l/min (USgpm) (USgpm) Power Power kw (hp) kw (hp) Case Flow Versus Outlet Pressure at 18 r/min, Full Flow 5 C (12 F) and 1. absolute ( psi gauge) Inlet Case 1,4 Flow (.37) Versus Outlet Pressure at 18 r/min, Full Flow 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1,4 1,2 (.37) (.32) Case Flow Case l/min Flow (USgpm) l/min (USgpm) Case Flow Case l/min Flow (USgpm) l/min (USgpm) 1,2 1, (.32) (.26) 1,,8 (.26) (.21),8,6 (.21) (.16),6,4 (.16) (.11),4,2 (.11) (.5),2 (.5) 5 1 15 2 25 (7) (15) (22) (29) (36) 5 1 Outlet Pressure 15 2 ( 25 (7) (15) (22) (29) (36) Case 5 (1.32) Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 5 (1.32) 4 (1.6) 4 (1.6) 3 (.79) 3 (.79) 2 (.53) 2 (.53) 1 (.26) 1 (.26) 5 1 15 2 (7) (15) (22) (29) 5 1 Outlet Pressure 15 2 ( (7) (15) (22) (29) 3 (44) 35 (5) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 25 (36) 25 (36) 3 (44) 3 (44) 3 (44) 35 (5) 35 (5) 35 (5) 2 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Efficiency % Delivery Delivery l/min l/min (USgpm) (USgpm) Torque Torque Nm Nm (in.lb.) (in.lb.) Performance Higher speed version (M) PVM18 Noise Noise Level Level dba dba Typical Noise Levels Petroleum Oil (1W) at 93 C (2 F), 1. Typical absolute Noise ( psi Levels gauge) Inlet (Sound Petroleum pressure Oil data (1W) equivalent at 93 C (2 F), to NFPA) 76 1. absolute ( psi gauge) Inlet 28 r/min(sound pressure data equivalent to NFPA) 76 72 Max. Flow 28 r/min 68 72 Max. Flow 68 64 64 6 28 r/min Min. Flow 56 6 28 r/min Min. Flow 6 r/min 56 52 Max. Flow 6 r/min 48 52 Max. Flow 48 6 r/min 44 Min. Flow 6 r/min 4 44 Min. Flow 5 1 15 2 25 3 35 4 (7) (15) (22) (29) (36) (44) (5) 5 1 Outlet Pressure 15 2 ( 25 3 35 (7) (15) (22) (29) (36) (44) (5) Versus Speed at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 95 Versus Speed at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 95 9 9 1 (15 85 1 (15 (22 85 15 (22 2 8 (29 2 8 (29 25 (36 75 25 (36 28 75 (4 28 32 (4 (46 7 32 5 (46 1 15 2 25 3 7 Speed r/min 5 1 15 2 25 3 Speed r/min Delivery Delivery and and Case Case Flow Flow Versus Versus Speed Speed @ 93 C 93 C (2 F), (2 F), full full flow flow and and 1. 1. absolute absolute ( ( gauge gauge Inlet Inlet 5 5 (13.2) (13.2) 45 45 (11.9) (11.9) 4 4 (1.6) (1.6) 35 35 (9.2) (9.2) 3 3 (7.9) (7.9) 25 25 (5.3) (5.3) 2 2 (5.3) (5.3) 15 15 (4.) (4.) 1 1 (2.6) (2.6) 25 25 (365 (365, Delivery, Delivery 25 25 (36 (36, Delivery, Delivery 25 25 (36 (36,, Case Case flow flow 5 (1.3) (1.3) 25 25 (365 (365,, Case Case flow flow 5 5 1 1 15 15 2 2 25 Speed 25 Speed r/min r/min 5 5 (442) (442) 15 15 (22 (22 4 4 (354) (354) 3 3 (265) (265) 1 1 (15 (15 2 2 (177) (177) 1 1 (88) (88) 25 25 (365 (365 5 5 1 Speed 15 2 Speed r/min r/min 25 25 3 3 3 3 4, 4, (1.1) (1.1) 3, 3, (.8) (.8) 2, 2, (.5) (.5) 1, 1, (.3) (.3) Torque Torque Versus Versus Speed Speed @ 93 C 93 C (2 F), (2 F), full full flow flow and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) inlet inlet 11 11 (973) (973) 1 1 (885) (885) 9 9 (796) (796) 28 28 (4 (4 8 8 (78) (78) 25 25 (36 (36 7 7 (619) (619) 2 2 (29 (29 6 6 (531) (531) 32 32 (46 (46 Case Case Flow Flow l/min l/min (USgpm) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 21
Torque - Nm (in.lb.) Torque - Nm (in.lb.) Case Flow (l/min (USgpm) Case Flow (l/min (USgpm) Performance Higher speed version (M) PVM18 Power @ Full Flow kw (hp) Power @ Full Flow kw (hp) Power Versus Speed @ 93 C (2 F), full flow and 1. absolute ( psi gauge) inlet 28 (37.5) 32 26 (34.9) Power Versus Speed (46 @ 93 C (2 F), full flow and 1. absolute ( psi gauge) inlet 24 (32.2) 28 28 (37.5) 32 (4 22 26 (29.5) (34.9) (46 25 2 24 (26.8) (32.2) 28 (36 18 (24.1) (4 22 (29.5) 2 16 (21.4) 25 (29 2 (26.8) (36 14 (18.8) 18 (24.1) 215 12 16 (16.1) (21.4) (29 (22 1 14 (13.4) (18.8) 1 8 (1.7) 15 (15 12 (16.1) (22 16 (13.4) (8.) 1 84 (1.7) (5.4) (15 25 26 (2.7) (8.) (365 4 (5.4) 5 1 15 2 25 253 2 (2.7) Speed r/min (365 5 1 15 2 25 3 Torque and Speed Case r/min Flow Versus Speed @ 93 C (2 F), load sense standby and 1. absolute ( psi gauge) inlet 3 (27) Torque and Case Flow Versus Speed @ 93 C (2 F), load sense standby and 1. absolute ( psi gauge) inlet 3 (27) 5 (442) 2 (18) 45 (398) 2 (3 4 (354) differential, Torque 2 (3 2 (18) 35 (31) differential, 1 (9) Case Flow 5 (1.32) 11 2 (3 (16 3 (265) 4 (1.6) differential, 2 3 (.79) Torque 11 (3 (16 25 (221) differential, differential, 2 (.53) 1 (9) Case Case Flow 5 (1.32) 2 (177) Flow 1 (.26) 11 (16 4 (1.6) 15 (135) differential, 5 1 15 2 25 3 3 (.79) Torque Speed r/min 11 (16 differential, 2 (.53) 1 (88) Case Flow 1 (.26) 5 (45) 5 1 15 2 25 3 Speed r/min Torque Nm (in.lb.) Torque and Case Flow Versus Speed @ 93 C (2 F), cut-off and 1. absolute ( psi gauge) inlet 15 (22 Torque 28 (4 Torque 28 (4, Case Flow 15 (22 Case Flow 5 1 15 2 25 Speed r/min 9 (2.4) 6 (1.6) 3 (.8) 22 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Performance Quiet version, optimized for 1-18 rpm (E) PVM2 Noise Level Noise dba Level dba Noise Level Noise dba Level dba 64 62 6 64 58 62 56 6 54 58 52 56 5 54 48 52 46 5 44 48 Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet Typical Noise Levels at 18 and 12 r/min 18 r/min Max. Flow with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 18 12 r/min r/min Max. Max. Flow Flow 12 r/min Max. Flow 18 r/min Min. Flow 18 r/min Min. Flow 42 46 12 r/min Min. Flow 4 44 5 1 15 2 25 (7) (15) (22) 12 r/min 42 (29) (36) Min. Flow 4 Typical 5 Noise Levels 1 at 15 and 1 2 r/min 25 (7) with Petroleum (15) Oil (1W) (22) at 5 C (12 F) (29) (36) and 1. Outlet absolute Pressure ( psi gauge) ( Inlet 64 62 Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) 15 and r/min 1. absolute ( psi gauge) Inlet 6 64 Max. Flow 58 62 15 r/min 56 6 Max. 1 Flow r/min 54 Max. Flow 58 52 56 5 54 48 52 1 r/min Max. Flow 15 r/min Min. Flow 46 5 44 15 r/min 1 r/min 48 Min. Flow Min. Flow 42 46 4 44 1 r/min 5 1 15 Min. Flow 2 25 42 (7) (15) (22) (29) (36) 4 Sound pressure 5 data 1 15 2 25 equivalent (7) to NFPA (15) (22) (29) (36) Sound pressure data equivalent to NFPA % torque torque Nm Nm (in.lb.) (in.lb.) Delivery and Efficiency at 18 r/min, 5 C (12 F), Delivery and and 1. Efficiency absolute at 18 ( psi r/min, gauge) 5 C Inlet (12 F), 1 and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Volumetric Efficiency 9 8 8 7 7 6 6 5 5 (13) 5 5 (13) 4 4 (11) 4 4 (11) 3 3 (8) 3 3 (8) 2 2 (5) 2 2 (5) 1 1 (3) 1 1 (3) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet Pressure (15) (22) ( (29) (36) Torque and Power at 18 r/min, 5 C (12 F), Torque and 1. and Power absolute at 18 ( psi r/min, gauge) 5 C Inlet (12 F), 12 (162) and 1. absolute ( psi gauge) Inlet 12 (162) 11 (973) 11 (973) 1 (885) 1 (885) 9 (796) 9 (796) 8 (78) 8 (78) 7 (619) 7 (619) 6 (531) Torque, 6 (531) Full Stroke Torque, 5 (442) 25 (34) 5 (442) 25 (34) 4 (354) 2 (27) 4 (354) Power, 2 (27) 3 (265) Full Stroke Power, 15 (2) 3 (265) 15 (2) 2 (177) Torque, 1 (13) 2 (177) Torque, 1 (13) 1 (88) Cut off 5 (7) 1 (88) Cut off 5 (7) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Delivery l/min l/min (USgpm) Power Power kw kw (hp) (hp) % torque torque Nm Nm (in.lb.) (in.lb.) Deli Deli 1 1 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 In In 12 ( 12 11 11 1 1 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 23
Performance Quiet version, optimized for 1-18 rpm (E) PVM2 3) 1) ) ) ) Delivery and Efficiency at 15 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet Delivery and Efficiency at 15 r/min, 5 C (12 F), 1 Volumetric and 1. Efficiency absolute ( psi gauge) Inlet 91 Volumetric Efficiency 8 9 7 8 6 7 5 6 4 5 3 4 2 3 1 2 1 5 (13) 4 (11) 5 (13) 3 (8) 4 (11) 2 (5) 3 (8) 1 (3) 2 (5) 1 (3) 5 1 15 2 25 (7) (15) (22) (29) (36) Outlet 5 Pressure 1 ( 15 2 25 (7) (15) (22) (29) (36) Efficiency Delivery and and Efficiency at at 12 12 r/min, r/min, 5 C 5 C (12 F), and and 1. 1. absolute ( ( psi psi gauge) Inlet Inlet 1 1 Volumetric Efficiency 9 9 Overall 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 Delivery flow) 5 5 1 1 15 15 2 2 (7) (7) (15) (15) (22) (22) (29) (29) Outlet Outlet Pressure ( ( 5 5 (13) (13) 4 4 (11) (11) 3 3 (8) (8) 2 2 (5) (5) 1 1 (3) (3) 25 25 (36) (36) Delivery ana and and1 1 1 Volum 9 9 8 8 7 7 Efficiency 6 6 5 5 4 4 3 3 2 2 1 1, F), 34) 27) 2) 13) ) Power kw (hp) Power kw (hp) Torque and Power at 15 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet Torque and Power at 15 r/min, 5 C (12 F), 12 (162) and 1. absolute ( psi gauge) Inlet 11 12 (973) (162) torque Nm (in.lb.) torque Nm (in.lb.) 111 (885) (973) 91 (796) (885) 8 (78) 9 (796) 7 (619) 8 (78) 6 (531) 7 (619) Torque, 5 (442) 6 (531) Torque, 25 (34) 4 (354) 5 (442) 2 (27) 25 (34) 3 (265) 4 (354) Power, 15 (2) (27) 2 (177) 3 (265) Power, 1 (13) 15 (2) 12 (88) (177) 5 (7) 1 (13) 1 (88) 5 (7) 5 1 15 2 25 (7) (15) (22) (29) (36) 5 1 15 2 25 Outlet (7) Pressure (15) ( (22) (29) (36) Power kw (hp) Power kw (hp) torque Nm (in.lb.) torque Nm (in.lb.) Torque and and Power Power at at 12 12 r/min, r/min, 5 C 5 C (12 F), and and 1. 1. absolute ( ( psi psi gauge) Inlet Inlet 12 12 (162) (162) 11 11 (973) (973) 1 1 (885) (885) 9 9 (796) (796) 8 8 (78) (78) 7 7 (619) (619) 6 6 (531) (531) Torque, Torque, Full 5 5 (442) Stroke (442) 25 25 (34) (34) 4 4 (354) (354) 2 2 (27) (27) Power, Power, 3 3 (265) (265) Full 15 Stroke 15 (2) (2) 2 2 (177) (177) 1 1 (13) (13) 1 1 (88) (88) 5 5 (7) (7) 5 5 1 1 15 15 2 2 25 25 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) Outlet Outlet Pressure ( ( Power kw (hp) Power kw (hp) torque Nm (in.lb.) torque Nm (in.lb.) T 12 12 (162 11 11 (973 1 1 (885 9 9 (79 (7 8 8 (7 (7 7 7 (61 (6 6 6 (53 (5 5 5 (44 (4 4 4 (35 (3 3 3 (26 (2 2 2 (17 (1 1 1(8 24 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Performance Quiet version, optimized for 1-18 rpm (E) PVM2 F), 3) 5 (13) 1) 4 (11) ) 3 (8) ) 2 (5) ) 1 (3) Delivery Delivery and and Efficiency Efficiency at 1 at 1 r/min, r/min, 5 C 5 C (12 F), (12 F), and and 1. 1. absolute absolute ( psi ( gauge) psi gauge) Inlet Inlet 1 1 Volumetric Volumetric Efficiency Efficiency 9 9 Overall Efficiency 8 8 7 7 6 6 5 5 5 (13) 5 (13) 4 3 2 1 4 3 2 Delivery Delivery (effective (effective flow) flow) 1 4 (11) 4 (11) 3 (8) 3 (8) 2 (5) 2 (5) 1 (3) 1 (3) 5 5 5 1 1 15 15 2 2 25 25 ) (7) (7)(15) (15)(22) (22)(29) (29) (36) (36) Outlet Outlet Pressure Pressure ( ( Case Flow l/min (USgpm) Case Flow versus Outlet Pressure at 18 r/min, Full Flow, Case Flow versus Outlet Pressure at 18 r/min, Full Flow, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 5 C (12 F), and 1. absolute ( psi gauge) Inlet 2.5 (.66) 2.5 (.66) 2.3 (.59) 2.3 (.59) 2. (.53) 2. (.53) 1.8 (.46) 1.8 (.46) 1.5 (.4) 1.5 (.4) 1.3 (.33) 1.3 (.33) 1. (.26) 1. (.26).8 (.2).8 (.2).5 (.13).5 (.13).3 (.7).3 (.7) 5 1 15 (7) 5 (15) 1 (22) 15 (7) (15) (22) Outlet Pressure ( 2 (29) 2 (29) 25 (36) 25 (36) 12 F), t (34) 25 (34) (27) 2 (27) (2) 15 (2) (13) 1 (13) ) 5 (7) 5 6) Power kw (hp) Power kw (hp) torque Nm (in.lb.) Torque Torque and and Power Power at 1 at 1 r/min, r/min, 5 C 5 C (12 F), (12 F), and and 1. 1. absolute absolute ( psi ( gauge) psi gauge) Inlet Inlet 12 (162) 12 (162) 11 (973) 11 (973) 1 (885) 1 (885) 9 (796) 9 (796) torque Nm (in.lb.) 8 (78) 8 (78) 7 (619) 7 (619) 6 (531) 6 (531) Torque, Torque, 5 (442) 5 (442) 25 (34) 25 (34) 4 (354) 4 (354) 2 (27) 2 (27) 3 (265) 3 (265) Power, Power, 15 (2) 15 (2) 2 (177) 2 (177) 1 (13) 1 (13) 1 (88) 1 (88) 5 (7) 5 (7) 5 51 1 15 15 2 2 25 25 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) Outlet Outlet Pressure Pressure ( ( Power kw (hp) Case Flow l/min (USgpm) Power kw (hp) Case Flow versus Outlet Pressure at Cutoff, 18 r/min, Case Flow versus Outlet Pressure at Cutoff, 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 5 C (12 F), and 1. absolute ( psi gauge) Inlet 1 (2.64) 1 (2.64) 9 (2.38) (2.38) 8 (2.11) (2.11) 7 (1.85) (1.85) 6 (1.59) (1.59) 5 (1.32) (1.32) 4 (1.6) (1.6) 3 (.79) (.79) 2 (.53) (.53) 1 (.26) (.26) 5 1 15 (7) 5 (15) 1 (22) 15 (7) (15) (22) Outlet Pressure ( 2 (29) 2 (29) 25 (36) 25 (36) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 25
Performance Higher speed version (M) PVM2 Typical Typical Noise Noise Levels Levels at 28 at 28 & 6 & 6 r/min r/min with with Petroleum Oil Oil (1W) (1W) at 93 C at 93 C (2 F) (2 F) and and 1. 1. absolute ( psi ( psi gauge) gauge) Inlet Inlet Typical Noise Levels at 7728 & 6 28 r/min 28 r/min with r/min Petroleum Oil (1W) at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 74 74 max. max. flow flow 77 28 71 r/min 71 74 max. flow 68 68 28 28 r/min r/min 71 min. min. flow flow 65 65 68 28 r/min 62 62 min. flow 65 59 59 62 56 56 59 53 53 56 5 5 6 6 r/min r/min max. max. flow flow 53 47 47 6 6 r/min r/min min. min. flow flow 5 44 446 r/min max. flow 47 41 41 6 r/min min. flow 44 5 5 1 1 15 15 2 2 25 25 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) 41 Outlet Outlet Pressure Pressure ( ( 5 Sound 1 Sound pressure pressure 15 data data 2 25 (7) (15) (22) (29) (36) equivalent to NFPA. to NFPA. Sound pressure data equivalent to NFPA. Noise Level dba Noise Level dba Noise Level dba Overall versus versus Speed Speed Delivery and and Case Case Flow Flow versus versus Speed Speed at 93 C at 93 C (2 F), at 93 C at 93 C (2 F) (2 F) and and 1. 1. absolute ( psi ( psi gauge) gauge) inlet inlet Full Full Flow Flow 1. 1. absolute ( psi ( psi gauge) gauge) inlet inlet 1 1 versus Speed Delivery and Case 6 Flow (15.9) 6 (15.9) versus Speed at 93 C (2 F), C (2 F) and 1. absolute ( psi gauge) inlet Full Flow 1. absolute ( psi gauge) inlet 95 95 55 (14.5) 55 (14.5) 15 15 6 (15.9) (22 (22 5 (13.2) 5 (13.2) 9 9 21 21 (3 (3 55 (14.5) 45 (11.9) 45 (11.9) 15 (22 5 (13.2) 5 5 (725 (725 85 85 1 1 (15 (15 4 (1.6) 4 (1.6) Delivery Delivery 21 (3 45 (11.9) 8 8 35 (9.2) 35 5 (9.2) (725 5 5 1 (7 (7 (15 4 (1.6) Delivery 21 21 (3 (3 3 (7.9) 3 (7.9) 75 75 Delivery Delivery 35 (9.2) 23 23 (33 (33 25 (6.6) 25 (6.6) 7 7 5 (7 21 (3 3 (7.9) 2 (5.3) 2 (5.3) Delivery 4 (1.6) 4 (1.6) 65 65 23 (33 25 (6.6) 15 (4.) 15 (4.) 3 (.79) 3 (.79) 6 6 2 (5.3) 1 (2.6) 1 (2.6) 21 21 (3 (3 Case 4 (1.6) Case Flow Flow 2 (.53) 2 (.53) 15 (4.) 55 55 5 (1.3) 5 (1.3) 3 (.79) 5 5 (725 (725 Case Case Flow Flow 1 (.26) 1 (.26) 1 (2.6) 21 (3 Case Flow 2 (.53) 5 5 5 5 1 1 15 15 2 2 25 25 53 (1.3) 3 5 (725 5Case 1 Flow 1151522252533 1 (.26) Speed Speed r/min r/min Speed Speed (r/min) (r/min) 5 1 15 2 25 3 5 1 15 2 25 3 Speed r/min Speed (r/min) (%) (%) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Case Flow l/min (USgpm) 26 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Torque Nm (lb.in.) Torque Torque Nm Nm (lb.in.) (lb.in.) Torque Nm (lb.in.) Torque Nm (lb.in.) Torque Torque Nm Nm (lb.in.) (lb.in.) Torque Nm (lb.in.) Power kw (hp) Power Power kw kw (hp) (hp) Power kw (hp) Performance Higher speed version (M) PVM2 Torque Torque versus versus Speed Speed at 93 C at 93 C (2 F), (2 F), Power Power versus versus Speed Speed at 93 C at 93 C (2 F), (2 F), Full Flow Full Flow and Torque 1. and versus 1. absolute Speed absolute ( at at psi 93 C ( gauge) psi (2 F), gauge) Inlet Inlet Full Flow Full Flow and Power 1. and versus 1. absolute Speed absolute ( at at psi 93 C ( gauge) psi (2 F), gauge) Inlet Inlet Full Flow and 1. 1. absolute ( ( psi psi gauge) Inlet Full Flow and 1. 1. absolute ( ( psi psi gauge) Inlet 11 (973) 11 (973) 24 (32) 24 (32) 11 11 (973) 23 23 (33 (33 1 (885) 1 (885) 24 (32) 22 (3) 24 22 (32) (3) 23 23 (33 1 1 (885) 22 (3) 9 (796) 9 (796) 2 (27) 222 (3) (27) 21 21 (3 (3 9 9 (796) 23 23 (33 (33 2 2 (27) (27) 8 (78) 8 (78) 18 (24) 18 (24) 21 23 23 (33 21 (3 8 8 (78) 18 18 (24) (24) 7 (619) 7 (619) 16 (21) 16 (21) 21 21 (3 (3 7 7 (619) 16 16 (21) (21) 21 21 (3 14 (19) 14 (19) 6 (531) 6 (531) 15 15 (22 (22 15 15 (22 (22 14 (19) 6 6 14 (19) (531) 12 (16) 12 (16) 15 5 (442) 5 (442) 15 15 (22 15 (22 12 12 (16) (16) 5 5 (442) 1 (13) 1 (13) 4 (354) 4 (354) 1 1 (15 (15 1 1 (15 (15 1 1 (13) (13) 4 4 (354) 1 1 (15 8 (11) 8 (11) 1 1 (15 3 (265) 3 (265) 88 (11) (11) 3 3 (265) 5 (725 5 (725 6 (8) 6 (8) 2 (177) 2 (177) 5 (725 6 (8) 5 (725 4 (5) 6 (8) 4 (5) 5 (725 5 (725 2 2 (177) 4 (5) 5 (725 4 (5) 5 (725 1 (88) 1 (88) 2 (3) 2 (3) 1 1 (88) (88) 22 (3) (3) 5 5 1 1 15 15 2 2 25 25 3 3 5 5 1 1 15 15 2 2 25 25 3 3 5 5 1 Speed Speed (r/min) 15 (r/min) 2 25 3 5 5 1 Speed Speed (r/min) 15 (r/min) 2 25 3 Speed (r/min) Speed (r/min) Torque Torque and Case and Case Flow Flow versus versus Speed Speed at at 93 C 93 C (2 F), Torque (2 F), Load and Load Sense Case Sense Standby Flow Standby versus 1. Speed and 1. at at 93 C (2 F), absolute absolute Load ( psi Sense ( gauge) psi Standby gauge) Inlet Inlet and 1. 1. 3.2 (28) 3.2 (28) absolute ( ( psi psi gauge) Inlet 3.3.2 (27) 3.2 (28) 3. (28) (27) 2.83. (25) 3. (27) 2.8 (27) (25) 2.8 (25) 2 2 (29 (29 diff. diff. 2.6 (23) 2.82.6 (25) (23) 2 diff. 2.6 (23) 2 Torque (29 Torque diff. 2.4 (21) 2.62.4 (23) (21) Torque 2.22.4 (19) 2.4 (21) 2.2 (21) (19) 22.2 (18) 2.2 (19) (19) 2 (18) 11 11 (16 (16 diff. diff. 1.8 (16) 22 (18) 1.8 (18) (16) 11 11 Torque (16 Torque diff. diff. 1.61.8 (14) 1.8 (16) 1.6 (16) (14) Torque Case Flow Case Flow 1.6 1.6 (14) l/min (14) Case l/min 1.4 (12) 1.4 (12) Flow (USgpm) 1.4 1.4 (12) l/min (USgpm) 1.2 (11) 1.2 (12) (11) (USgpm) 1.21 1.2 (9) (11) (11) 1 (9) 5. (1.32) 5. (1.32) 11 (9) (9).8 (7) 5. 5..8 (7) 4. (1.6) 4. (1.32) (1.6) 11 11 (16 (16 diff. diff..6 (5).8 (7) 4..8 (7).6 (5) Case 11 diff. 4.3. (1.6) (.79) 11 Flow Case (16 Flow 3. (.79) diff..6.6(5) (5).4 (4) Case 2 2 (29 (29 diff. diff..4 (4) Flow 2.3. (.53) 3. 2. (.79) (.53) Case 2 diff..4.4(4) 2 Flow Case (29 Flow.2 (2) diff. (4).2 (2) 1.2. (.26) 2. 1. (.53) (.26) Case Flow.2.2(2) (2) 1. 1. (.26) 5 5 1 1 15 15 2 2 25 25 3 3 5 5 Speed 1 Speed (r/min) 15 (r/min) 2 25 3 Speed (r/min) Torque Torque and Case and Case Flow Flow versus versus Speed Speed at 93 C at 93 C (2 F), Torque (2 F), Pressure and Case Pressure Limit Flow Limit Cut-off versus Cut-off and Speed and at at 1. 93 C 1. absolute (2 F), absolute Pressure ( psi ( gauge) psi Limit gauge) Inlet Cut-off Inlet and 3 (265) 3 (265) 1. 1. absolute ( ( psi psi gauge) Inlet 3 3 (265) 27 (239) 27 (239) 21 21 (3 (3 27 24 (212) 27 24 (239) (212) 21 21 Torque (3 Torque 24 24 (212) Torque 21 (186) 21 (186) 21 21 (186) 18 (159) 18 (159) 18 18 (159) 15 (133) 15 (133) Case Case 15 15 (133) 15 15 Flow l/min Flow 15 Casel/min 12 (16) 12 (16) (22 15 (22 (USgpm) Flow (USgpm) l/min 12 12 (16) (22 Torque Torque 9 (8) 9 (8) (USgpm) Torque 9 (2.4) 9 (2.4) 99 (8) (8) 99 (2.4) 6 (53) 6 (53) 21 21 (3 (3 Case Flow Case Flow 6 (1.6) 6 (1.6) 66 (53) (53) 21 21 (3 Case Flow 66 (1.6) 3 (27) 3 (27) 15 15 (22 (22 Case Flow Case Flow 3 (.8) 3 (.8) 33 (27) (27) 15 15 (22 Case Flow 33 (.8) 5 5 1 1 15 15 2 2 25 25 3 3 5 5 Speed 1 Speed (r/min) 15(r/min) 2 25 3 Speed (r/min) Torque Nm (lb.in.) Torque Torque Nm Nm (lb.in.) (lb.in.) Torque Nm (lb.in.) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 27
Performance Quiet version, optimized for 1-18 rpm (E) PVM45 Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) Delivery and Efficiency at 18 r/min Typical Noise and Levels 1. absolute at 18 ( and psi gauge) 12 Inlet r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 72 with Petroleum Oil (1W) at 5 C (12 F) 1 and 1. absolute ( psi gauge) Inlet Volumetric Efficiency 72 7 9 Delivery and Efficiency at 18 r/min 18 r/min 5 C (12 F) and 1. absolute Overall ( Efficiency psi gauge) Inlet 7 68 Max. Flow 8 1 18 r/min 68 66Max. Flow Volumetric Efficiency 7 9 66 64 6 62 18 r/min 8 64 Min. Flow 62 6 18 r/min 5 7 Min. Flow 6 58 12 r/min 4 12 (27) Max. Flow 6 58 5612 r/min Max. Flow 3 5 76 (2) 54 12 r/min 56 Min. Flow 2 4 49 (13) 12 (27) 54 52 12 r/min Min. Flow 1 3 27 (7) 76 (2) 52 5 2 49 (13) 5 48 5 1 15 2 25 3 35 5 1 15 2 25 3 1 (7) (15) (22) (29) (36) (44) (5) 48 (7) (15) (22) (29) (36) (44) 27 (7) Sound pressure data 5 1Outlet 15 Pressure 2 ( 25 3 equivalent to NFPA (7) (15) (22) (29) (36) (44) Sound pressure data Torque 5 1 and Power 15 at 2 1825 r/min 3 35 equivalent to NFPA 5 C (12 F) (7) and (15) 1. (22) absolute (29) ( psi gauge) (36) Inlet (44) (5) Typical Noise Levels at 15 and 1 r/min 24 (2125) with Petroleum Oil (1W) at 5 C (12 F) Typical Noise and Levels 1. absolute at 15 ( and psi gauge) 1 Inlet r/min Torque and Power at 18 r/min 72 with Petroleum Oil (1W) at 5 C (12 F) 21 (186) and 1. absolute ( psi gauge) Inlet 5 C (12 F) and 1. Torque, absolute ( psi gauge) Inlet 24 (2125) 72 7 15 r/min Max. Flow 15 r/min 18 (1595) 7 15 r/min Min. Flow 68 21 (186) Max. Flow 15 Power, 1 r/min r/min 15 (1325) Torque, 5 (67) Min. Max. Flow 68 Flow 66 1 r/min 18 (1595) Max. Flow 12 (16) 4 (54) 66 64 Power, 15 (1325) 5 (67) 9 (795) 64 3 (4) 62 1 r/min 12 (16) 4 (54) 62 6 Min. Flow 6 (53) Torque, 2 (27) 1 r/min 9 (795) Cut-off 6 3 (4) 58 Min. Flow 3 (265) 1 (13) 58 56 6 (53) Torque, 2 (27) 5 1 15 2 Cut-off 56 54 25 3 35 3 (265) (7) (15) (22) (29) (36) (44) (5) 1 (13) 54 52 5 1 15 2 25 3 52 (7) (15) (22) (29) (36) (44) 5 1 15 2 25 3 35 5 1Outlet 15 Pressure 2 ( 25 3 (7) (15) (22) (29) (36) (44) (5) (7) (15) (22) (29) (36) (44) Noise Level dba Noise Level dba Noise Level dba Noise Level dba torque Nm (in.lb.) torque Nm (in.lb.) Power kw (hp) Power kw (hp) 28 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Power kw (hp) Power kw (hp) Performance Quiet version, optimized for 1-18 rpm (E) PVM45 torque Nm (in.lb.) torque Nm (in.lb.) Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. Overall absolute Efficiency ( psi gauge) Inlet 81 Volumetric Efficiency 7 9 6 8 5 7 4 6 3 5 12 (27) 76 (2) 2 4 12 49 (13) (27) 1 3 76 27 (2) (7) 2 49 (13) 5 1 15 2 25 3 35 1 (7) (15) (22) (29) (36) (44) (5) 27 (7) 5 1 15 2 25 3 35 (7) Torque (15) and (22) Power (29) at 15 (36) r/min (44) (5) 5 C (12 F) and Outlet 1. Pressure absolute (( gauge) Inlet 24 (2125) 21 (186) 24 (2125) 18 (1595) Torque and Power at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet Torque, 21 (186) 15 (1325) 18 (1595) Torque, 12 (16) 4 (54) 15 (1325) Power, 9 (795) 3 (4) 12 (16) 4 (54) Power, 6 (53) 2 (27) 9 (795) 3 (4) 3 (265) 6 (53) 1 (13) 2 (27) 3 (265) 5 1 15 2 25 3 351 (13) (7) (15) (22) (29) (36) (44) (5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque Nm (in.lb.) Delivery l/min Delivery (USgpm) l/min (USgpm) Power kw Power (hp) kw (hp) Delivery and Efficiency at 12 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency Delivery and Efficiency at 12 r/min 9 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 8 Volumetric Efficiency 7 9 8 6 7 5 4 6 76 (2) 5 3 57 (15) 4 76 (2) 2 38 (1) 3 57 (15) 1 19 (5) 2 38 (1) 5 1 15 2 25 3 35 1 19 (5) (7) (15) (22) (29) (36) (44) (5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque Outlet and Pressure Power at 12 ( r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 24 (2125) Torque and Power at 12 r/min 21 (186) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 24 (2125) Torque, 18 (1595) 21 (186) 15 (1325) Torque, 18 (1595) 12 (16) 15 (1325) Power, 9 (795) 3 (4) 12 (16) Power, 6 (53) 2 (27) 9 (795) 3 (4) 3 (265) 6 (53) 1 (13) 2 (27) 3 (265) 5 1 15 2 25 3 35 1 (13) (7) (15) (22) (29) (36) (44) (5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque Nm (in.lb.) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 29
Case Flow Case l/min Flow (USgpm) l/min (USgpm) Case Flow Case l/min Flow (USgpm) l/min (USgpm) Performance Quiet version, optimized for 1-18 rpm (E) PVM45 Torque Nm Torque (in.lb.) Nm (in.lb.) Delivery and Efficiency at 1 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency at 1 r/min 9 5 C (12 F) Overall and 1. Efficiency absolute ( psi gauge) Inlet 1 Volumetric Efficiency 8 9 7 Volumetric Efficiency 8 6 7 5 6 4 5 3 4 2 3 1 2 5 1 15 2 25 3 1 (7) (15) (22) (29) (36) (44) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) Torque Outlet and Pressure Power at 1 ( r/min 5 C (12 F), and 1. absolute ( psi gauge) Inlet 24 (2125) Torque and Power at 1 r/min 21 (186) 5 C (12 F), and 1. absolute ( psi gauge) Inlet 24 (2125) Torque, 18 (1595) 21 (186) Torque, 15 (1325) 18 (1595) 12 (16) 15 (1325) 9 (795) Power, 12 (16) 6 (53) 9 (795) Power, 3 (265) 6 (53) 3 (265) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) Efficiency Efficiency % % 76 (2) 35 (5) 35 (5) 57 (15) 76 (2) 38 (1) 57 (15) 19 (5) 38 (1) 19 (5) 35 (5) 3 (4) 2 (27) 3 (4) 1 (13) 2 (27) 1 (13) 35 (5) Power kw (hp) Power kw (hp) Case Flow Versus Outlet Pressure at 18 r/min, Full Flow 5 C (12 F) and 1. absolute ( psi gauge) Inlet 2, (.53) Case Flow Versus Outlet Pressure at 18 r/min, Full Flow 1,8 (.47) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 2, (.53) 1,6 (.42) 1,8 (.47) 1,4 (.37) 1,6 (.42) 1,2 (.32) 1,4 (.37) 1, (.26) 1,2 (.32),8 (.21) 1, (.26),6 (.16),8 (.21),4 (.1),6 (.16),2 (.5),4 (.1),2 (.5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Case Flow Versus Outlet Pressure Pressure ( at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 6 (1.59) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 65 (1.59) (1.32) 54 (1.32) (1.6) 43 (1.6) (.79) 3 2 (.79) (.53) 21 (.53) (.26) 1 (.26) 5 1 15 2 25 (7) (15) (22) (29) (36) 5 1 15 2 25 (7) (15) (22) (29) (36) 3 (44) 3 (44) 35 (5) 35 (5) 3 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Case Flow l/min (USgpm) Case Flow l/min (USgpm) Performance Higher speed version (M) PVM45 Noise Level dba Noise Level dba Typical Typical Noise Noise Levels Levels Delivery and Case Flow Versus Speed Petroleum Petroleum Oil Oil (1W) (1W) at at 93 C 93 C (2 F), (2 F), @ 93 C (2 F), full flow and 1. absolute ( gauge Inlet 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 12 (32) (Sound (Sound pressure pressure data data equivalent equivalent to to NFPA) NFPA) 82 11 (29) 82 Delivery 5 and Case (7, Flow Versus Speed 26 26 r/min r/min @ 93 C (2 F), full flow and 1. absolute ( gauge Inlet Max. Max. Flow 1 (26) Delivery Flow 78 12 (32) 78 9 (24) 11 (29) 5 (728, (4, 74 8 (21) 74 1 (26) Delivery Delivery 7 (18) 9 (24) 7 7 6 (16) 28 (4, 6 6 r/min r/min 8 (21) 26 Delivery 26 r/min r/min Min. Min. Flow 2,5 (.7) 66 Flow 5 (13) 66 Min. Min. Flow Flow 7 (18) 4 (11) 28 (4, 2, (.5) 6 (16) 62 Case flow 62 3 (8) 1,5 (.4) 2,5 (.7) 5 (13) 2 (5) 1, (.3) 58 4 (11) 28 (4, 2, (.5) 58 6 6 r/min r/min 5 (7, Max. Max. Flow Flow 1 (3) Case flow 3 (8) Case flow,5 (.1) 1,5 (.4) 54 54 2 (5) 1, (.3) 5 1 15 2 25 3 5 (7, 5 Speed r/min 5 1 (3) Case flow,5 (.1) 5 5 1 1 15 15 2 2 25 25 3 3 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) (44) (44) Outlet Outlet Pressure Pressure ( ( 5 Torque 1 Versus 15 Speed 2 25 3 @ 93 C (2 F), full flow and 1. Speed absolute r/min( psi gauge) inlet 225 (1991) 21 (1858) 28 (4 Torque Versus Speed Overall Versus Versus Speed Speed 195 (1726) @ 93 C (2 F), full flow and 1. absolute ( psi gauge) inlet at at 93 C 93 C (2 F) (2 F) and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 225 (1991) 25 (36 18 (1593) 95 95 21 (1858) 28 (4 165 (146) 1 1 195 (1726) 2 (29 15 (1327) (15 25 (36 (15 18 (1593) 9 9 135 (1195) 15 (22 165 (146) 15 15 12 (162) 2 (29 (22 (22 15 (929) 15 (1327) 1 (15 85 135 (1195) 15 (22 85 5 5 9 (796) 2 2 (7 (7 75 (664) 12 (162) (29 (29 6 (531) 15 (929) 5 1 (7 (15 8 8 45 (398) 9 (796) 25 (365 75 (664) 25 25 3 (265) 17 (25 6 (531) (7 (36 (36 75 75 17 17 45 (398) 5 1 15 2 25 (365 3 28 (25 28 (25 Speed r/min 3 (265) 17 (25 (4 (4 7 5 1 15 2 25 3 7 5 5 1 1 15 15 2 2 25 25 3 3 Speed r/min Speed Speed r/min r/min Torque Nm (in.lb.) Torque Nm (in.lb.) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 31
Performance Higher speed version (M) PVM45 Power Versus Speed 93 C (2 F), 1. absolute ( psi gauge) Inlet 56 (75) 28 (4) 52 (7) Power Versus Speed 93 C (2 F), 1. absolute ( psi gauge) 25 Inlet (36) 4856 (64) (75) 28 (4) 4452 (59) (7) 4 (54) 2 25 (29) (36) 48 (64) 3644 (48) (59) 324 (43) (54) 2 (29) 15 (22) 2836 (38) (48) 2432 (32) (43) 1 (15) 2 (27) 15 (22) 28 (38) 1624 (21) (32) 12 (16) 5 1 (7) (15) 2 (27) 816 (11) (21) 25 (365) 12 4 (5) (16) 17 5 (25) (7) 8(11) 5 1 15 2 25 25 3 (365) 4 (5) Speed r/min 17 (25) 1.Case Flow at 26 r/min, Full Flow 93 C (2 F), 5 1.1 absolute 15 (2 psi gauge) 25Inlet 3 Speed r/min 6 (1.6) 5 (1.3) 1.Case Flow at 26 r/min, Full Flow 4 (1.1) 93 C (2 F), 1. absolute ( psi gauge) Inlet 3 (.8) 6 (1.6) 2 (.5) 5 (1.3) 1 (.3) 4 (1.1) 3 (.8) 2 (.5) 5 1 15 2 25 3 35 (7) (15)(22) (29)(36) (44)(5) 1 (.3) 5 1 15 2 25 3 35 Case (7) Flow (15) at (22) Cutoff (29) at 26 (36) r/min (44)(5) 93 C (2 F), Outlet 1. Pressure absolute ( psi ( gauge) Inlet 42 (11.1) 38 (1.) Case Flow at Cutoff at 26 r/min 34 (9.) 93 C (2 F), 1. absolute ( psi gauge) Inlet 42 (11.1) 3 (7.9) 38 (1.) 26 (6.9) 34 (9.) 22 (5.8) 3 (7.9) 18 (4.8) 26 (6.9) 14 (3.7) 22 (5.8) 1 (2.6) 18 (4.8) 5 1 15 2 25 3 35 14 (3.7) (7) (15) (22) (29) (36) (44) (5) 1 (2.6) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Power @ Full Flow kw (hp) Power @ Full Flow kw (hp) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Pressure ( Pressure ( 32 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Torque Torque Nm (in-lb) Nm (in-lb) Efficiency Efficiency % % Delivery Delivery l/min (USgpm) l/min (USgpm) Efficiency Efficiency % % Performance Quiet version, optimized for 1-18 rpm (E) PVM5 Noise Level dba Noise Level dba Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 72 18 r/min Typical max. Noise flow Levels at 18 and 12 r/min with 68Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 72 64 12 r/min max. 18 flow r/min max. flow 68 6 64 56 6 52 56 48 52 44 48 44 12 r/min max. 18 flow r/min min. flow 18 r/min min. flow 5 (7) 5 (7) 1 (15) 1 (15) 15 (22) 15 (22) 12 r/min min. flow 12 r/min min. flow 2 (29) 2 (29) 25 (36) 25 (36) Delivery and Efficiency at 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet Delivery and Efficiency at 18 r/min, 5 C (12 F), 1 and 1. absolute ( psi gauge) Inlet Volumetric Efficiency 9 1 8 Volumetric Efficiency 9 7 8 7 6 5 6 4 5 3 4 2 3 1 2 1 5 1 15 2 (7) (15) (22) (29) 5 Outlet 1 Pressure 15 ( 2 (7) (15) (22) (29) 125 (33) 1 (26) 125 (33) 75 (2) 1 (26) 5 (13) 75 (2) 25 (7) 5 (13) 25 25 (7) (36) 25 (36) Del Deliv 1 9 1 8 9 7 8 7 6 5 6 4 5 3 4 2 3 1 2 1 Noise Level dba Noise Level dba Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 72 Typical Noise Levels at 15 and max. 1 flow r/min with 68Petroleum Oil (1W) at 5 C (12 F) and 1. 15 r/min absolute ( psi gauge) Inlet max. flow 72 64 1 r/min max. flow 68 6 64 56 6 52 56 48 52 44 48 15 r/min max. flow 5 (7) 15 r/min min. flow 15 r/min min. flow 1 (15) 1 r/min 1 r/min min. flow 1 r/min min. flow 15 (22) 44 Sound pressure data equivalent 5 to NFPA. 1 15 (7) (15) (22) Sound pressure data equivalent to NFPA. 2 (29) 2 (29) 25 (36) 25 (36) Torque and Power at 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet Torque 24 (2124) and Power at 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 22 (1947) 24 (2124) 2 (177) 22 (1947) 18 (1593) 2 (177) Torque, 16 (1416) 18 (1593) 14 (1239) Torque, 16 (1416) 12 (162) 14 (1239) 1 (885) 5 (67) 12 (162) 8 (78) Power, 4 (54) 1 (885) 6 (531) 5 (67) 3 (4) 8 (78) Power, 4 (354) Torque, 4 (54) 2 (27) 6 (531) Cut-off 2 (177) 3 (4) 1 (13) 4 (354) Torque, 2 (27) Cut-off 2 (177) 5 1 15 2 251 (13) (7) (15) (22) (29) (36) 5 Outlet 1 Pressure 15 ( 2 25 (7) (15) (22) (29) (36) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 Power Power kw (hp) kw (hp) 33 Torque Torque Nm (in-lb) Nm (in-lb) In In2 2 24 2 22 1 2 1 18 1 16 1 14 12 1
Delivery Delivery l/min l/min (USgpm) (USgpm) Efficiency % Torque Torque Nm Nm (in.lb.) (in.lb.) Performance Quiet version, optimized for 1-18 rpm (E) PVM5 Delivery and Efficiency at 15 r/min, 5 C (12 F), Delivery and and 1. Efficiency absolute at 15 ( psi r/min, gauge) 5 C Inlet (12 F), 1 and 1. absolute ( psi gauge) Inlet Volumetric Efficiency 1 9 Volumetric Efficiency 9 8 7 8 7 6 5 6 5 4 3 4 3 2 1 2 1 5 (7) 5 (7) 1 15 2 (15) (22) (29) 1 15 2 Outlet (15) Pressure (22) ( (29) 125 (33) 125 (33) 1 (26) 75 1 (2) (26) 75 (2) 5 (13) 25 5 (7) (13) 25 (7) 25 (36) 25 (36) Delivery Delivery l/min l/min (USgpm) (USgpm) Delivery and Efficiency at 12 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 8 7 6 5 4 3 2 1 125 (33) 1 (26) 75 (2) 5 (13) 25 (7) 5 1 15 2 25 (7) (15) (22) (29) (36) Deliver a 1 9 8 7 6 5 4 3 2 1 ) ) ) ) ) Power Power kw (hp) kw (hp) Torque Torque Nm Nm (in-lb) (in-lb) Torque and Power at 15 r/min, 5 C (12 F), Torque and 1. and Power absolute at 15 ( psi r/min, gauge) 5 C Inlet (12 F), 24 (2124) and 1. absolute ( psi gauge) Inlet 22 24 (1947) (2124) 2 22 (177) (1947) 18 2 (1593) (177) 16 18 (1416) (1593) 14 16 (1239) (1416) 12 14 (162) (1239) 12 1 (162) (885) 1 8 (78) (885) 6 8 (531) (78) 4 6 (354) (531) 2 4 (177) (354) Torque, Full Stroke Torque, Power, Full Stroke Power, 2 (177) 5 1 15 2 (7) (15) (22) (29) 5 1 15 2 (7) Outlet (15) Pressure (22) ( (29) 5 (67) 4 5 (54) (67) 3 4 (4) (54) 2 3 (27) (4) 1 2 (13) (27) 1 (13) 25 (36) 25 (36) Power Power kw (hp) kw (hp) Torque and Power at 12 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 24 (2124) 22 (1947) 2 (177) 18 (1593) 16 (1416) 14 (1239) 12 (162) 1 (885) 8 (78) 6 (531) 4 (354) 2 (177) 5 1 (7) (15) Torque, Power, 15 (22) 2 (29) 5 (67) 4 (54) 3 (4) 2 (27) 1 (13) 25 (36) Power kw (hp) Torque Nm (in.lb.) In 2 2 2 1 1 1 1 34 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Case Case Flow Flow l/min l/min (USgpm) (USgpm) Case Case Flow Flow l/min l/min (USgpm) (USgpm) Performance Quiet version, optimized for 1-18 rpm (E) PVM5 )(33) )(26) 2) 13) 7) Delivery Delivery and and Efficiency Efficiency at at 1 1 r/min, r/min, 5 C 5 C (12 F), (12 F), and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 1 1 Volumetric Efficiency 9 Volumetric Efficiency 9 8 8 7 7 6 6 5 5 4 4 3 3 Delivery Delivery (effective (effective flow) flow) 2 2 1 1 5 5 1 1 15 15 2 2 (7) (7) (15) (15) (22) (22) (29) (29) Outlet Outlet Pressure Pressure ( ( 125 125 (33) (33) 1 1 (26) (26) 75 (2) 75 (2) 5 (13) 5 (13) 25 (7) 25 (7) 25 25 (36) (36) Case Flow versus Outlet Pressure at 18 r/min, Full Flow, Case Flow versus Outlet Pressure at 18 r/min, Full Flow, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 1. (.26) 5 C (12 F), and 1. absolute ( psi gauge) Inlet 1. (.26).9 (.24).9 (.24).8 (.21).8 (.21).7 (.18).7 (.18).6 (.16).6 (.16).5 (.13).5 (.13).4 (.11).4 (.11).3 (.8).3 (.8).2 (.5).2 (.5).1 (.3).1 (.3) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Outlet Pressure ( F), )(67) )(54) )(4) )(27) )(13) Power kw (hp) Power kw (hp) Torque Nm (in.lb.) Torque Nm (in.lb.) Torque Torque and and Power Power at at 1 1 r/min, r/min, 5 C 5 C (12 F), (12 F), and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 24 24 (2124) (2124) 22 22 (1947) (1947) 2 2 (177) (177) 18 18 (1593) (1593) Torque, Torque, 16 16 (1416) (1416) Full Stroke 14 14 (1239) (1239) 12 12 (162) (162) 1 1 (885) (885) 5 (67) 5 (67) 8 (78) 8 (78) 4 (54) 4 (54) 6 (531) 6 (531) Power, Power, 3 (4) 3 (4) 4 (354) 4 (354) 2 (27) 2 (27) 2 (177) 2 (177) 1 (13) 1 (13) 5 5 1 1 15 15 2 2 25 25 (7) (7) (15) (15)(22) (22)(29) (29)(36) (36) Outlet Outlet Pressure Pressure ( ( Power kw (hp) Power kw (hp) Case Flow versus Outlet Pressure at Cutoff, 18 r/min, Case Flow versus Outlet Pressure at Cutoff, 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 5 C (12 F), and 1. absolute ( psi gauge) Inlet 1 (2.64) 1 (2.64) 9 (2.38) (2.38) 8 (2.11) (2.11) 7 (1.85) (1.85) 6 (1.59) (1.59) 5 (1.32) (1.32) 4 (1.6) (1.6) 3 (.79) (.79) 2 (.53) (.53) 1 (.26) (.26) 5 1 15 (7) 5 (15) 1 (22) 15 (7) (15) (22) Outlet Pressure ( 2 (29) 2 (29) 25 (36) 25 (36) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 35
(%) (%) (%) Noise Level dba Noise Level dba Noise Level dba Performance Higher speed version (M) PVM5 Typical Typical Noise Levels Noise Levels at 26 at & 26 r/min & 6 r/min with Petroleum with Petroleum Oil (1W) Oil at (1W) 93 C at (2 F) 93 C (2 F) and and 1. 1. absolute absolute ( psi gauge) ( psi gauge) inlet inlet 88 88 86 84 86 84 82 82 26 r/min 26 r/min max. flowmax. flow 88 8 8 86 78 78 26 r/min 26 r/min min. flowmin. 84 flow 76 76 74 74 82 72 72 6 8 r/min 6 r/min max. flowmax. flow 7 7 78 68 68 76 66 66 6 r/min 6 r/min 74 min. flowmin. flow 64 64 5 1 15 72 5 1 15 2 225 25 (7) (7) (15) (15) (22) (22) (29) (29) 7 (36) (36) Outlet Pressure ( 68 Sound pressure Sound pressure data data equivalent equivalent to NFPA. to NFPA. 66 64 Typical Noise Levels at 26 & 6 r/min with Petroleum Oil (1W) at 93 C (2 F) and 1. absolute ( psi gauge) inlet 26 r/min max. flow 6 r/min min. flow 5 1 15 (7) (15) (22) Sound pressure data equivalent to NFPA. 26 r/min min. flow 2 (29) 6 r/min max. flow 25 (36) 1 Overall Efficiency versus versus Speed Speed at 93 C at (2 F) 93 C (2 F) and 1. and 1. absolute absolute ( psi gauge) ( psi gauge) inlet inlet 95 9 85 8 75 7 65 6 55 5 1 95 1 (15 1 (15 12 (32) versus 12 (32) Speed 9 at 93 C (2 F) and 1. 11 absolute (29) 11 (29) 5 (725 5 (725 ( psi gauge) Delivery inlet Delivery 2 85 2 1 (26) 1 (26) 1 (29 (29 21 (3 2114 (37) (3 9 (24) 9 (24) 8 Delivery Delivery 95 8 (21) 8 (21) 13 (34) 1 (15 12 (32) 75 7 (18) 7 (18) 21 (3 21 (3 9 6 (16) 6 (16) 11 (29) 7 21 (3 21 (3 23 (33 23 (33 85 2 5 (13) 5 (13) 1 (26) Case Flow Case Flow 5 (1.32) 65 (29 4 (11) 4 (11) 9 (24) 4 (1.6) 8 8 (21) 6 3 (8) 3 (8) 3 (.79) 75 7 (18) 21 (3 2 (5) 2 (5) 5 (725 5 (725 2 (.53) 55 6 (16) 7 1 (3) 1 (3) Case Flow Case Flow 1 (.26) 23 (33 5 (13) 5 5 5 1 1 15 15 2 2 65 25 25 3 3 5 1 5 1 15 15 2 2 25 425 3 (11) Speed (r/min) Speed (r/min) 6 Speed (r/min) Speed (r/min) 3 (8) 2 (5) 55 1 (3) 5 Delivery Delivery and Case and Flow Case versus Flow versus Speed Speed at 93 C at (2 F), 93 C (2 F), Full Flow Full and Flow 1. and 1. absolute absolute ( psi gauge) ( psi gauge) inlet inlet 14 (37) 13 (34) 14 (37) 13 (34) 5 1 15 2 25 Speed (r/min) 3 Delivery and Case Flow ver Full Flow and 1. abs Case Flow l/min (USgpm) Case Flow l/min (USgpm) 5 (1.32) 4 (1.6) 3 (.79) 2 (.53) 1 (.26) 3 5 De 5 1 15 Speed 36 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Torque Torque Nm Nm (in.lb.) (in.lb.) Torque Nm (in.lb.) Torque Nm (in.lb.) Performance Higher speed version (M) PVM5 Torque Nm (in.lb.) Torque Torque versus Speed versus at Speed 93 C at at (2 F), 93 C (2 F), Full Flow Full Full and Flow 1. and and 1. 1. absolute absolute ( psi gauge) ( ( psi psi gauge) Inlet Inlet 3 (2655) 3 3 (2655) 275 (2434) 275 275 (2434) 25 (2212) 25 25 (2212) 23 23 23 (33 (33 225 (1991) 225 225 21 (1991) 21 21 (3 (3 2 (177) 2 2 (177) Torque Nm (in.lb.) Torque Nm (in.lb.) 175 (1549) 175 175 (1549) 15 (1327) 15 15 (1327) 125 (116) 125 125 (116) 1 (885) 1 1 (885) (885) 75 (664) 75 75 (664) (664) 2 2 (29 2 (29 1 1 (15 1 (15 5 (442) 5 5 (442) (442) 17 (25 17 17 (25 (25 25 (221) 25 25 (221) (221) 5 5 1 5 1 15 1 15 15 2 2 25 2 25 3 25 3 3 Speed (r/min) Speed (r/min) Power kw (hp) Power versus Power Speed versus at Speed 93 C at at (2 F), 93 C (2 F), Full Flow Full Full and Flow 1. and and 1. 1. absolute absolute ( psi gauge) ( ( psi psi gauge) Inlet Inlet 6 (8) 6 6 (8) (8) 55 (74) 55 55 (74) (74) 23 (33 23 23 (33 5 (67) 5 5 (67) (67) 21 (3 21 21 (3 2 (29 2 2 (29 45 (6) 45 45 (6) (6) 4 (54) 4 4 (54) (54) Power kw (hp) Power kw (hp) 35 (47) 35 35 (47) (47) 3 (4) 3 3 (4) (4) 25 (34) 25 25 (34) (34) 2 (27) 2 2 (27) (27) 15 (2) 15 15 (2) (2) 1 (13) 1 1 (13) (13) 5 (7) 55 (7) (7) 1 (15 1 1 (15 17 (25 17 17 (25 (25 5 1 5 5 1 15 1 15 2 15 2 25 2 25 3 25 3 3 Speed (r/min) Speed (r/min) Torque Nm (in.lb.) Torque Torque and Case and and Flow Case versus Flow Speed versus at Speed at at 93 C (2 F), 93 C (2 F), Load Sense Load Standby Sense Standby 1. and and 1. 1. absolute absolute ( psi gauge) ( ( psi psi gauge) Inlet Inlet 8 (71) 88 (71) (71) 7 (62) 77 (62) (62) 2 (3 2 2 (3 diff. (3 diff. diff. Torque Torque 6 (53) 66 (53) (53) Torque Nm (in.lb.) Torque Nm (in.lb.) 5 (44) 55 (44) (44) 4 (35) 44 (35) (35) 3 (27) 33 (27) (27) 2 (3 2 2 (3 (3 diff. Case diff. diff. Flow Case Case Flow Flow 2 (18) 22 (18) (18) 11 (16 11 11 (16 (16 diff.case diff.case Flow Flow Flow 1 (9) 11 (9) (9) Case Flow Case Case Flow Flow l/min l/min (USgpm) (USgpm) 5. (1.32) 5. 5. (1.32) 11 (16 11 11 (16 diff. (16 diff. diff. Torque Torque 4. (1.6) 4. 4. (1.6) 3. (.79) 3. 3. (.79) (.79) 2. (.53) 2. 2. (.53) (.53) 1. (.26) 1. 1. (.26) (.26) 5 5 1 5 1 1 15 15 2 15 2 2 25 25 3 25 3 3 Speed (r/min) Speed (r/min) Torque Torque and Case and and Flow Case versus Flow Speed versus Speed at 93 C at at (2 F), 93 C (2 F), Pressure Pressure Limit Cut-off Limit Cut-off and and and 1. 1. 1. absolute absolute ( psi gauge) ( ( psi psi gauge) Inlet Inlet 55 (487) 55 55 (487) (487) 5 (442) 5 5 (442) (442) 45 (398) 45 45 (398) (398) 21 21 (3 21 (3 Torque Torque 4 (354) 4 4 (354) (354) 21 21 21 35 (31) 35 (3 35 (31) (31) (3 3 (265) Case 3 3 (265) (265) Flow Case Case Flow Flow Case Case Case Flow l/min Flow Flow l/min 25 (221) 25 25 (221) (221) (USgpm) (USgpm) 2 (177) 2 2 (177) (177) 12 (3.2) 12 12 (3.2) (3.2) 15 (133) 15 15 15 (133) (133) 15 (22 15 (22 Torque Torque 9 (2.4) 99 (2.4) (2.4) 1 (88) 1 1 (88) (88) 6 (1.6) 66 (1.6) (1.6) 5 (44) 5 5 (44) (44) 15 15 (22 15 (22 Case Flow Case Case Flow Flow 3 (.8) 33 (.8) (.8) 5 5 1 5 1 15 1 15 15 2 2 25 2 25 3 25 3 3 Speed (r/min) Speed (r/min) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 37
Power kw (hp) Power kw (hp) Performance Quiet version, optimized for 1-18 rpm (E) PVM57 Noise Level dba Noise Level dba 74 7 66 Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 18 r/min Max. Flow 18 r/min Min. Flow 1 9 8 7 6 Delivery and Efficiency at 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet Delivery and Efficiency at 18 r/min Volumetric Efficiency 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 8 5 6 13 (34) 12 r/min Max. Flow 62 4 5 14 (28) 13 (34) 3 4 78 (21) 14 (28) 58 2 3 52 (14) 78 (21) 12 r/min Min. Flow 1 2 26 (7) 52 (14) 54 1 26 (7) 5 1 15 2 25 3 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (7) (15) (22) (29) (36) (44) (5) 5 Outlet Pressure 1 15 ( 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) (Sound pressure data equivalent to NFPA) Torque and Power at 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) 3 (2655) Torque and Power at 18 r/min and 1. absolute ( psi gauge) Inlet 5 C (12 F) and 1. absolute ( psi gauge) Inlet 27 (239) Torque, 7 3 (2655) 24 (2124) 27 (239) Torque, 15 r/min Max. Flow 21 (1859) 24 (2124) 66 18 (1593) 21 (1859) 6 (8) 1 r/min Max. Flow 15 (1328) 18 (1593) 5 (67) 6 (8) 15 r/min 12 (162) Power, Min. Flow 15 (1328) 4 (54) 62 5 (67) 9 (797) 12 (162) Power, 3 (4) 4 (54) 6 (531) 9 (797) 2 (27) 3 (4) 58 1 r/min 3 (266) 6 (531) Torque, 1 (13) 2 (27) Min. Flow Cut-off 3 (266) 5 1 15 2 25 3 35 Torque, 1 (13) (7) (15) (22) (29) (36) (44) Cut-off (5) 54 5 Outlet Pressure 1 15 ( 2 25 3 35 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) (5) (7) (15) (22) (29) (36) (44) Torque Nm (in.lb.) Torque Nm (in.lb.) 7 38 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Power kw (hp) Power kw (hp) Performance Quiet version, optimized for 1-18 rpm (E) PVM57 Torque Nm (in.lb.) Torque Nm (in.lb.) Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency at 15 Volumetric r/minefficiency 9 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 8 Volumetric Efficiency 9 7 8 6 7 5 1 (26) 6 4 8 (21) 5 1 (26) 3 6 (16) 4 8 (21) 2 4 (11) 3 6 (16) 1 2 (5) 2 4 (11) 1 5 (7) 1 (15) 15 (22) 2 (29) 25 (36) 3 (44) 35 2 (5) (5) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque Outlet and Pressure Power at 15 ( r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 33 (2921) Torque and Power at 15 r/min 3 (2655) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 33 (2921) 27 (239) 3 (2655) 24 (2124) Torque, 27 (239) 21 (1859) Torque, 24 (2124) 18 (1593) 6 (8) 21 (1859) Power, 15 (1328) 5 (67) 18 (1593) 6 (8) 12 (162) Power, 4 (54) 15 (1328) 5 (67) 9 (797) 3 (4) 12 (162) 6 (531) 9 (797) 3 (266) 4 (54) 2 (27) 3 (4) 1 (13) 6 (531) 2 (27) 5 1 15 2 25 3 35 3 (266) (7) (15) (22) (29) (36) (44) (5) 1 (13) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque Nm (in.lb.) Delivery and Efficiency at 12 r/min 5 C (12 F) Delivery and 1. and absolute Efficiency ( psi at gauge) 12 Inlet r/min 1 5 C (12 F) and 1. absolute ( psi gauge) Inlet Volumetric 1 Efficiency 9 Volumetric Efficiency 9 8 8 7 7 6 6 5 1 (26) 5 1 (26) 4 8 (21) 4 8 (21) 3 6 (16) 3 6 (16) 2 4 (11) 2 4 (11) 1 2 (5) 1 2 (5) 5 1 15 2 25 3 35 (7) (15) (22) 1 (29) 15 (36) 2 25 (44) 3 (5) 35 (7) Outlet (15) Pressure (22) (29) ( (36) (44) (5) Torque and Power at 12 r/min 5 C (12 F) and Torque 1. absolute and Power ( psi gauge) at 12 Inlet r/min 33 (2921) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 33 (2921) 3 (2655) 3 (2655) 27 (239) 27 (239) Torque, 24 (2124) Torque, 24 (2124) 21 (1859) 21 (1859) 18 (1593) 18 (1593) 15 (1328) Power, 15 (1328) Power, 4 (54) 12 (162) 4 (54) 12 (162) 3 (4) 9 (797) 3 (4) 9 (797) 6 (531) 2 (27) 6 (531) 2 (27) 3 (266) 1 (13) 3 (266) 1 (13) 5 1 15 2 25 3 35 (7) (15) (22) 1 (29) 15 (36) 2 25 (44) 3 (5) 35 (7) Outlet (15) Pressure (22) (29) ( (36) (44) (5) Torque Nm (in.lb.) Power kw (hp) Power kw (hp) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 39
Power kw (hp) Power kw (hp) Performance Quiet version, optimized for 1-18 rpm (E) PVM57 Torque Nm (in.lb.) Delivery and Efficiency at 1 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency Volumetric at 1 Efficiency r/min 9 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 8 9 7 6 5 8 7 6 4 3 2 5 4 3 1 2 1 5 (7) 1 (15) 15 (22) 2 (29) 25 (36) 3 (44) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) Torque Outlet and Power Pressure at 1 ( r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 33 (2921) Torque and Power at 1 r/min 3 (2655) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 33 (2921) 27 (239) 3 (2655) Torque, 24 (2124) 27 (239) 21 (1859) Torque, 24 (2124) 18 (1593) 21 (1859) 15 (1328) 18 (1593) 12 (162) Power, 15 (1328) 9 (797) 12 (162) Power, 6 (531) 9 (797) 3 (266) 6 (531) 3 (266) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) Torque Nm (in.lb.) 8 (21) 35 (5) 6 (16) 8 (21) 4 (11) 6 (16) 2 (5) 4 (11) 2 (5) 35 (5) 4 (54) 3 (4) 4 (54) 2 (27) 3 (4) 1 (13) 2 (27) 35 1 (13) (5) 35 (5) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Case Case Flow Flow Versus Versus Outlet Outlet Pressure at at Full Full Flow, Flow, 18 18 r/min r/min 5 C 5 C (12 F) (12 F) and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 5 (1.32) 5 (1.32) 4 (1.6) 4 (1.6) 3 (.79) 3 (.79) 2 (.53) 2 (.53) 1 (.26) 1 (.26) 1, 1, (.26) (.26),9,9 (.24) (.24),8,8 (.21) (.21),7,7 (.18) (.18),6,6 (.16) (.16) 5 5 1 1 15 15 2 2 25 25 3 3 35 35 (7) (7) (15) (15)(22) (22) (29) (29)(36) (36) (44) (44)(5) (5) Outlet Outlet Pressure Pressure ( ( Case Case Flow Flow Versus Versus Outlet Outlet Pressure at at Cutoff, Cutoff, 18 18 r/min r/min 5 C 5 C (12 F) (12 F) and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 1,1 1,1 (.29) (.29),5,5 (.13) (.13) 5 5 1 1 15 15 2 2 25 25 3 3 35 35 (7) (7) (15) (15) (22) (22) (29) (29)(36) (36) (44) (44)(5) (5) Outlet Outlet Pressure Pressure ( ( 4 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Case Flow l/min (USgpm) Case Flow l/min (USgpm) Performance Higher speed version (M) PVM57 Noise Level dba Typical Noise Levels Delivery and Case Flow Versus Speed Petroleum Oil (1W) at 93 C (2 F), @ 93 C (2 F), full flow and 1. absolute ( gauge Inlet 1. absolute ( psi gauge) Inlet 15 (4) 82 14 (37) Delivery and 5 Case (7 Flow, Versus Speed 13 (34) @ 93 C (2 F), full flow Delivery and 1. absolute ( gauge Inlet 78 25 r/min 12 (32) 15 (4) Max. Flow 25 r/min Min. Flow 11 (29) 14 (37) 74 5 (7, 1 (26) 13 (34) Delivery 9 (24) 12 (32) 7 28 (4, 8 (21) 11 (29) Delivery 66 7 (18) 1 (26) 6 (16) 9 (24) 28 (4, 28 (4 6, (1.6), Case flow 62 5 (13) 8 (21) Delivery 5, (1.3) 6 r/min 4 (11) 7 (18) 4, (1.1) Max. Flow 58 3 (8) 6 (16) 28 (4, 3, (.8) 6, (1.6) Case flow 6 r/min 2 (5) 5 (13) 5 (7, 2, (.5) 5, (1.3) Min. Flow 54 1 (3) 4 (11) Case flow 1, (.3) 4, (1.1) 3 (8) 3, (.8) 5 2 (5) 5 1 15 2 5 (7 25, 2, (.5) 5 1 15 2 25 3 Speed r/min Case flow 1 (3) 1, (.3) (7) (15) (22) (29) (36) (44) 5 Torque Versus 1 Speed 15 2 25 (Sound pressure @ 93 C (2 F), full Speed flow and r/min data equivalent to NFPA) 1. absolute ( psi gauge) inlet 32 (2832) Torque Versus Speed 32 Versus Speed 3 (2655) @ 93 C (2 F), full flow and (46 at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 28 (2478) 1. absolute ( psi gauge) inlet 95 26 (1858) 32 (2832) 5 32 24 (2124) 3 (2655) (7 25 (46 22 (1947) 28 (2478) (36 9 1 2 (177) 26 (1858) 2 (15 18 (1593) 24 (2124) (29 25 15 16 (1416) 22 (1947) 85 (36 (22 14 (1239) 15 2 (177) (22 2 12 (162) 2 18 (1593) 8 (29 1 (885) 16 (1416) 1 (29 (15 8 (78) 14 (1239) 15 (22 6 (531) 12 (162) 5 75 (7 4 (354) 1 (885) 1 25 2 (177) 17 (15 (36 8 (78) (25 6 (531) 5 7 5 1 15 2 25 3 (7 28 4 (354) Speed r/min (4 2 (177) 17 (25 65 5 1 15 2 25 5 1 15 2 25 3 Speed r/min Speed r/min Torque Nm (in.lb.) Torque Nm (in.lb.) 28 (4 28 (4 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 41
Case Flow l/min (USgpm) Performance Higher speed version (M) PVM57 Torque Nm (in.lb.) Power Versus Speed 93 C (2 F), 1. absolute ( psi gauge) Inlet 78 (15) 32 (46) 72 (97) 66 (89) 28 (4) 6 (8) 25 (36) 54 (72) 48 (64) 2 (29) 42 (56) 36 (48) 15 (22) 3 (4) 24 (32) 1 (15) 18 (24) 12 (16) 5 (7) 6 (8) 17 (25) 5 1 15 Speed r/min 2 25 Torque and Case Flow Versus Speed @ 93 C (2 F), load sense standby and 1. absolute ( psi gauge) inlet 6 (53) 2 (3 5 (44) differential, 11 (16 Torque 4 (35) differential, 8. (2.11) 3 (27) Torque 6. (1.58) 2 (18) 4. (1.6) 11 (16 differential, 1 (9) Case Flow 2. (.53) 2 (3 differential, Case Flow 5 1 15 2 25 Speed r/min Torque and Case Flow Versus Speed @ 93 C (2 F), cut-off and 1. absolute ( psi gauge) inlet 1 (885) 9 (796) 28 (4 Torque 8 (78) 7 (619) 28 6 (531) (4 5 (442) Case Flow 1 (2.6) 4 (354) 8 (2.1) 3 (265) 15 (22, Case Flow 6 (1.6) 2 (177) 4 (1.1) 15 (22, Torque 1 (88) 5 1 15 2 25 2 (.5) Speed r/min Power @ Full Flow kw (hp) Torque Nm (in.lb.) Case Flow l/min (USgpm) Pressure ( 42 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Noise Level dba Noise Level dba Performance Quiet version, optimized for 1-18 rpm (E) PVM63 Typical Noise Levels at 18 and 12 r/min. with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 75 Typical 18 Noise r/min Levels at 18 and 12 r/min. with max. flow Petroleum Oil (1W) at 5 C (12 F) and 1. 7 absolute ( psi gauge) Inlet 75 12 r/min 18 r/min max. flow min. 18 flowr/min 65 max. flow 7 6 65 55 6 5 55 5 18 r/min min. flow 5 (7) 5 (7) 12 r/min max. flow 1 15 (15) (22) 1 15 (15) (22) 12 r/min min. flow 12 r/min min. 2flow (29) 2 (29) 25 (36) 25 (36) Delivery and Efficiency at 18 r/min, 5C (12F), Delivery and 1. and Efficiency absolute at ( 18 psi gauge) r/min, Inlet 5C (12F), and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency Volumetric Efficiency 9 9 8 8 7 7 6 12 (32) 6 12 (32) 5 1 (26) 5 1 (26) 4 8 (21) 4 8 (21) 3 6 (16) 3 6 (16) 2 4 (11) 2 4 (11) 1 2 (5) 1 2 (5) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Delive Deli a 1 1 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 Noise Level dba Noise Level dba 75Typical Noise Levels at 15 and 1 r/min. with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute 15 r/min ( psi gauge) Inlet 7 75 65 7 6 65 55 6 5 55 5 Typical Noise Levels at 15 and 1 r/min. with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 15 r/min min. flow 15 r/min min. flow 5 (7) Sound pressure data equivalent to 5 NFPA. (7) 1 (15) 15 (22) Sound pressure data equivalent to NFPA. max. flow 15 r/min max. flow 1 r/min min. flow 1 r/min 1 min. flow 15 (15) (22) 2 (29) 2 (29) 1 r/min max. flow 1 r/min max. flow 25 (36) 25 (36) Torque Nm (in.lb.) Torque Nm (in.lb.) Torque and Power at 18 r/min, 5C (12F), and Torque 1. and absolute Power ( at psi 18 gauge) r/min, Inlet 5C (12F), and 1. absolute ( psi gauge) Inlet 27 (239) 27 (239) 24 (2124) 24 (2124) 21 (1859) 21 (1859) Torque, Full Stroke Torque, 18 (1593) 18 (1593) 15 (1328) 5 (67) 15 (1328) 5 (67) 12 (162) 4 (54) 12 (162) 4 (54) 9 (1327) Power, 3 (4) 9 (1327) Full Stroke Power, 3 (4) 6 (531) 2 (27) 6 (531) 2 (27) Torque, 3 (226) Cut-off Torque, 1 (13) 3 (226) Cut-off 1 (13) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 Power kw (hp) Power kw (hp) 43 Torque Nm (in.lb.) Torque Nm (in.lb.) Inpu In 27 2 24 2 21 2 18 1 15 1 12 1 9 6 3
Torque Torque Nm Nm (in.lb.) (in.lb.) Performance Quiet version, optimized for 1-18 rpm (E) PVM63 2) ) 6) ) ) ) ) Delivery l/min l/min (USgpm) Efficiency % % Delivery and Efficiency at 15 r/min, 5C (12F), Delivery and and 1. Efficiency absolute at 15 ( psi r/min, gauge) 5C Inlet (12F), and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency Volumetric Efficiency 9 9 8 8 7 7 6 6 5 5 4 4 3 3 1 (26) 1 (26) 8 (21) 8 (21) 6 (16) 6 (16) 2 2 4 (11) 4 (11) 1 1 2 (5) 2 (5) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Outlet Pressure ( Delivery l/min l/min (USgpm) Delivery Delivery and and Efficiency Efficiency at at 12 12 r/min, r/min, 5C 5C (12F), (12F), and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 1 1 Volumetric Volumetric Efficiency Efficiency 9 9 Overall Overall Efficiency Efficiency 8 8 7 7 Efficiency % 6 6 5 5 4 4 3 3 2 2 1 1 Delivery Delivery (effective (effective flow) flow) 5 5 1 1 15 15 (7) (7) (15) (15) (22) (22) Outlet Outlet Pressure Pressure ( ( 2 2 (29) (29) 1 1 (26) (26) 8 8 (21) (21) 6 6 (16) (16) 4 4 (11) (11) 2 2 (5) (5) 25 25 (36) (36) Delivery Delivery -l/min -l/min (USgpm) (USgpm) Delivery Delivery a and and 1 1 9 9 8 8 7 7 Efficiency % 6 6 5 5 4 4 3 3 2 2 1 1 ) ) ) ) ) Power kw kw (hp) (hp) Torque Nm Nm (in.lb.) Torque and Power at 15 r/min, 5C (12F), Torque and 1. and Power absolute at 15 ( psi r/min, gauge) 5C Inlet (12F), and 1. absolute ( psi gauge) Inlet 27 (239) 27 (239) 24 (2124) 24 (2124) Torque, 21 (1859) Torque, 21 (1859) 18 (1593) 18 (1593) 15 (1328) 5 (67) 15 (1328) 5 (67) 12 (162) 4 (54) 12 (162) 4 (54) 9 (1327) 3 (4) 9 (1327) 3 (4) 6 (531) Power, 2 (27) 6 (531) Power, 2 (27) 3 (226) 1 (13) 3 (226) 1 (13) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Outlet Pressure ( Power kw kw (hp) (hp) Torque Torque Nm Nm (in.lb.) (in.lb.) Torque Torque and and Power Power at at 12 12 r/min, r/min, 5C 5C (12F), (12F), and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 27 27 (239) (239) 24 24 (2124) (2124) 21 21 (1859) (1859) 18 18 (1593) (1593) 15 15 (1328) (1328) 12 12 (162) (162) 9 9 (1327) (1327) 6 6 (531) (531) 3 3 (226) (226) Torque, Torque, Full Full Stroke Stroke 5 5 (67) (67) 4 4 (54) (54) Power, Power, Full Full Stroke Stroke 3 3 (4) (4) 2 2 (27) (27) 1 1 (13) (13) 5 5 1 1 15 15 2 2 25 25 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) Outlet Outlet Pressure Pressure ( ( Power Power kw kw (hp) (hp) Inpu 27 27 (2 ( 24 24 (2 ( 21 21 (1 ( 18 18 (1 ( 15 15 (1 ( 12 12 (1 ( 9 9 (1 ( 6 6 ( 3 3 ( 44 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Torque Nm (in.lb.) Torque Nm (in.lb.) Performance Quiet version, optimized for 1-18 rpm (E) PVM63 ), (26) (26) 21) (21) 16) (16) 11) (11) 5) (5) ) Delivery -l/min (USgpm) Delivery -l/min (USgpm) Delivery and Efficiency at 1 r/min, 5C (12F), Delivery and Efficiency at 1 r/min, 5C (12F), and 1. absolute ( psi gauge) Inlet and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency Volumetric Efficiency 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 8 (21) 8 (21) 6 (16) 6 (16) 4 (11) 4 (11) 2 (5) 2 (5) 5 1 15 2 25 5 1 15 2 25 (7) (15) (22) (29) (36) (7) (15) (22) (29) (36) 1 (26) 1 (26) Case Flow l/min - (USgpm) Case Flow versus Outlet Pressure at 18 r/min, Full Flow, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 5 (1.32) 4 (1.6) 3 (.79) 2 (.53) 1 (.26) 5 (7) 1 (15) 15 (22) 2 (29) Outlet Pressure - ( 25 (36) F), 12F), t (67) 5 (67) (54) 4 (54) (4) 3 (4) (27) 2 (27) (13) 1 (13) ) ) Power kw (hp) Power kw (hp) Torque and Power at 1 r/min, 5C (12F), Torque and Power at 1 r/min, 5C (12F), and 1. absolute ( psi gauge) Inlet and 1. absolute ( psi gauge) Inlet 27 (239) 27 (239) 24 (2124) 24 (2124) 21 (1859) 21 (1859) 18 (1593) 18 (1593) 15 (1328) 15 (1328) 12 (162) 12 (162) 9 (1327) 9 (1327) Torque, Full Stroke Torque, 5 (67) 5 (67) 4 (54) 4 (54) 3 (4) 3 (4) 6 (531) 6 (531) 2 (27) 2 (27) 3 (226) 3 (226) Power, Full Stroke Power, 1 (13) 1 (13) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) (15) (22) (29) (36) Power kw (hp) Power kw (hp) Case Flow l/min - (USgpm) Case Flow versus Outlet Pressure at Cutoff, 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 12 (3.17) 11 (2.91) 1 (2.64) 9 (2.38) 8 (2.11) 7 (1.85) 6 (1.59) 5 (1.32) 4 (1.6) 3 (.79) 2 (.53) 1 (.26) 5 (7) 1 (15) 15 (22) 2 (29) Outlet Pressure - ( 25 (36) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 45
Case Flow l/min (USgpm) Case Flow l/min (USgpm) Performance Higher speed version (M) PVM63 Typical Typical Noise Noise Levels Levels at 25 at & 25 6 & r/min 6 r/min with Petroleum with Petroleum Oil (1W) Oil (1W) at 93 C at (2 F) 93 C (2 F) and 1. and 1. absolute absolute ( psi gauge) ( psi gauge) Inlet Inlet 85 85 25 r/min 25 r/min min. flowmin. flow 8 8 25 r/min 25 r/min max. flowmax. flow 75 75 Typical Noise Levels at 25 & 6 r/min with Petroleum Oil (1W) at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 7 7 85 Noise Level dba 65 6 55 Noise Level dba 65 6 55 5 5 5 5 1 115 15 2 (7) (7)(15) (15) (22) (22) (29) Outlet Pressure ( Sound pressure Sound pressure data data equivalent equivalent to NFPA. to NFPA. 8 6 r/min 6 r/min max. flowmax. flow 75 6 r/min 6 r/min min. flowmin. flow 7 Noise Level dba 2 6525 (29) (36) 6 55 25 (36) 25 r/min min. flow 25 r/min max. flow 6 r/min max. flow 6 r/min min. flow 5 5 1 15 (7) (15) (22) Sound pressure data equivalent to NFPA. 2 (29) 25 (36) Overall Efficiency versus versus Speed Speed at 93 C at (2 F) 93 C (2 F) and 1. and 1. absolute absolute ( psi gauge) ( psi gauge) inlet inlet Delivery Delivery and Case and Flow Case versus Flow versus Speed Speed at 93 C at (2 F), 93 C (2 F), Full Flow Full 1. Flow 1. absolute absolute ( psi gauge) ( psi gauge) Inlet Inlet (%) 1 95 9 85 8 75 7 65 6 55 (%) 1 95 9 1 1 (145 85 (145 8 5 (725 5 (725 75 15 15 (22 7 (22 65 23 23 (33 (33 21 6 21 (3 (3 55 5 5 75 15 5 5 1 1 15 15 2 2 25 25 3 3 7 (22 Speed Speed r/min r/min 65 6 21 (3 55 (%) 14 (37) 14 (37) 5 (725 5 (725 12 (32) 12 (32) Delivery Delivery versus Speed Delivery and Case Flow versu at 93 C (2 F) and 1. 1 absolute (26) 1 (26)( psi gauge) inlet Full Flow 1. absolut 21 21 (3 (3 16 (42) 1 8 (21) 8 (21) Delivery Delivery 95 9 85 8 1 (145 5 (725 16 (42) 16 (42) 6 (16) 4 (11) 2 (5) 23 (33 6 (16) 4 (11) 2 (5) 126 (32) (1.59) 6 (1.59) 21 21 (3 (3 Case Flow Case Flow 4 (1.6) 1 (26) 4 (1.6) 5 (725 5 (725 Case Flow Case Flow 2 (.53) 2 (.53) 8 (21) 14 8 (37) (2.11) 8 (2.11) 5 5 1 1 15 15 2 2 25 25 3 6 (16) 3 Speed (r/min) Speed (r/min) 4 (11) 2 (5) 5 (725 Delivery 2 D 21 (3 p 5 (725 psi 5 5 1 15 2 25 Speed r/min 3 5 1 15 Speed (r/m 46 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Case Flow l/min (USgpm) Case Case Flow l/min (USgpm) Case Flow Flow l/min l/min (USgpm) (USgpm) Case Flow l/min (USgpm) Case Case Flow l/min (USgpm) Case Flow Flow l/min l/min (USgpm) (USgpm) Performance Higher speed version (M) PVM63 Torque Nm (in.lb.) Torque Nm (in.lb.) Torque Nm (in.lb.) Torque Nm (in.lb.) Torque Nm (in.lb.) Torque Nm (in.lb.) Torque versus Speed at at 93 C 93 C (2 F), Full Full Flow Flow and and 1. 1. absolute ( psi ( psi gauge) Inlet Inlet 3 3 (2655) (2655) Torque versus Speed at 93 C (2 F), Full Flow and 1. absolute ( psi gauge) Inlet 25 25 (2212) 3 (2212) (2655) 2 2 (177) 25 (177) (2212) 15 15 (1327) 2 (1327) (177) 1 1 15 (885) (885) (1327) 23 23 (33 (33 21 21 (3 (3 23 (33 21 (3 15 15 (22 (22 15 (22 1 1 (15 (15 5 51 (725 (725 (15 5 (442) 5 1 (442) (885) 17 17 (25 (25 5 (725 5 (442) 5 51 115 152 225 253 17 3 (25 Speed Speed (r/min) (r/min) 5 1 15 2 25 3 Speed (r/min) Torque and and Case Case Flow Flow versus Speed at at 93 C 93 C (2 F), Load Load Sense Sense Standby and and 1. 1. absolute ( psi ( psi gauge) Inlet Inlet Torque and Case Flow versus Speed 8 (71) 8 (71) at 93 C (2 F), Load Sense Standby 2. and 2. (5.28) (5.28) 1. absolute ( psi gauge) Inlet 18. 18. (4.76) (4.76) 7 (62) 78 (62) (71) 2. (5.28) 2 2 (3 (3 16. 16. (4.23) (4.23) 6 (53) 6 (53) 18. (4.76) 7 (62) diff. diff. Torque Torque 14. 14. (3.7) (3.7) 5 (44) 5 (44) 2 (3 16. (4.23) 6 (53) diff. Torque 12. 12. (3.17) (3.17) 14. (3.7) 4 (35) 4 (35) 11 11 (16 (16 diff. diff. 1. 1. (2.64) (2.64) 5 (44) 12. (3.17) Torque Torque 8. 8. (2.11) (2.11) 3 (27) 3 4 (27) (35) 2 2 (3 (3 11 (16 diff. 1. (2.64) 6. 6. (1.59) (1.59) diff. diff. Case Case Flow Flow Torque 2 (18) 2 (18) 8. (2.11) 3 (27) 2 (3 4. 4. (1.6) (1.6) 11 11 (16 (16 diff. diff. 1 (9) 1 (9) 6. (1.59) diff. Case Flow 2 (18) Case Case Flow Flow 2. (.53) 2. (.53) 4. (1.6) 11 (16 diff. 1 (9) 5 5 1 115 15 Case 2 2 Flow 25 253 3 2. (.53) Speed Speed (r/min) (r/min) 5 1 15 2 25 3 Speed (r/min) Torque Nm (in.lb.) Torque Nm (in.lb.) Torque Nm (in.lb.) Power versus Speed at at 93 C 93 C (2 F), Full Full Flow Flow and and 1. 1. absolute ( psi ( psi gauge) Inlet Inlet 1 1 (134) (134) Power versus Speed at 93 C (2 F), Full Flow and 1. absolute ( psi gauge) Inlet 9 (121) 9 (121) 1 (134) 8 (17) 8 (17) 9 (121) 23 23 (33 (33 7 (94) 7 (94) 8 (17) 21 21 (3 (3 6 (8) 6 (8) 23 (33 7 (94) 21 (3 5 (67) 5 (67) 6 (8) 15 15 (22 (22 4 (54) 4 (54) 5 (67) 3 (4) 3 (4) 1 1 15 (15 (15 (22 4 (54) 2 (27) 2 (27) 3 (4) 5 51 (725 (725 (15 1 (13) 1 (13) 2 (27) 17 17 (25 (25 5 (725 1 (13) 5 51 115 152 225 253 3 17 (25 Speed Speed (r/min) (r/min) 5 1 15 2 25 3 Speed (r/min) Torque and and Case Case Flow Flow versus Speed at at 93 C 93 C (2 F), Pressure Limit Limit Cut-off and and 1. 1. absolute ( psi ( psi gauge) Inlet Inlet Torque and Case Flow versus Speed 8 (78) 8 at (78) 93 C (2 F), Pressure Limit Cut-off and 2. 2. 1. (5.28) (5.28) 21 absolute 21 (3 (3 ( gauge) Torque Torque Inlet 7 (619) 7 (619) 18. 18. (4.76) (4.76) 8 (78) 2. (5.28) 16. 16. (4.23) (4.23) 6 (531) 6 (531) 21 21 (3 Case Case FlowTorque 7 (619) 18. (4.76) 14. 14. (3.7) (3.7) 16. (4.23) 5 (442) 5 6 (442) (531) 21 (3 Case Flow 12. 12. (3.17) (3.17) 15 15 (22 (22 14. (3.7) 4 (354) 4 5 (354) (442) Case Case Flow Flow 1. 1. (2.64) (2.64) 12. (3.17) 3 (265) 3 (265) 15 (22 8. 8. (2.11) (2.11) 4 (354) Case Flow 1. (2.64) 6. 6. (1.59) (1.59) 2 (177) 2 3 (177) (265) 8. (2.11) 15 15 (22 (22 Torque Torque 4. 4. (1.6) (1.6) 1 (88) 1 (88) 6. (1.59) 2 (177) 2. 2. (.53) (.53) 15 (22 Torque 4. (1.6) 1 (88) 5 5 1 1 15 15 2 2 25 25 3 3 2. (.53) Speed Speed (r/min) (r/min) 5 1 15 2 25 3 Power kw (hp) Power kw (hp) Power kw (hp) Speed (r/min) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 47
Performance Quiet version, optimized for 1-18 rpm (E) PVM74 Noise Level Noise dba Level dba Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 76 Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) 74 18 r/min and 1. absolute ( psi gauge) Max. Inlet Flow 76 72 74 18 r/min Max. 18 Flow r/min 7 Min. Flow 72 68 18 r/min 7 Min. Flow 66 68 12 r/min 64 Max. Flow 66 62 12 r/min 64 Max. Flow 6 12 r/min 62 Min. Flow 58 6 5 1 15 2 25 (7) 12 (15) r/min(22) (29) (36) Min. Flow 58 Sound pressure 5 data 1 15 2 25 equivalent (7) to NFPA. (15) (22) (29) (36) Sound pressure data equivalent to NFPA. 3 (44) 3 (44) Delivery and Efficiency at 18 r/min 5 C (12 F) Delivery and 1. and Efficiency absolute ( at psi 18 gauge) r/min Inlet 1 5 C (12 F) and 1. absolute ( psi gauge) Inlet Volumetric 1 Efficiency 9 Volumetric Efficiency 9 8 8 7 7 6 15 (4) 6 15 (4) 5 125 (33) 5 125 (33) 4 3 2 1 4 3 2 1 1 (26) 1 (26) 75 (2) 75 (2) 5 (13) 5 (13) 25 (7) 25 (7) 5 1 15 2 25 3 35 (7) 5 (15) 1(22) 15(29) 2(36) 25(44) 3(5) 35 (7) Outlet (15) Pressure (22) (29) ( (36) (44) (5) Noise Level Noise dba Level dba Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 72 Typical Noise Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) 7 and 1. absolute ( psi gauge) 1 Inletr/min 72 Min. Flow 68 7 1 r/min Min. Flow 66 15 r/min 68 Max. Flow 64 15 r/min 66 Min. Flow 15 r/min 62 Max. Flow 64 15 r/min Min. 1 Flow r/min 6 Max. Flow 62 58 1 r/min 6 Max. Flow 56 58 5 1 15 2 25 (7) (15) (22) (29) (36) 56 5 1 15 2 25 (7) (15) (22) (29) (36) Torque Nm (in.lb.) 3 (44) 3 (44) Torque and Power at 18 r/min 5 C (12 F) and Torque 1. and absolute Power ( psi at gauge) 18 r/min Inlet 4 (354) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 4 (354) 36 (3186) Torque, 36 (3186) Torque, 32 (2832) 32 (2832) 28 (2478) 28 (2478) 24 (2124) 24 (2124) 2 (177) 2 (177) Power, 16 (1416) Full StrokePower, 8 (17) 16 (1416) 8 (17) 12 (162) 6 (8) 12 (162) 6 (8) 8 (78) Torque, 4 (54) 8 (78) Cut-off Torque, 4 (54) Cut-off 4 (354) 2 (27) 4 (354) 2 (27) 5 1 15 2 25 3 35 (7) 5(15) 1 (22) 15(29) 2 (36) 25(44) 3(5) 35 (7) Outlet (15) Pressure (22) (29) ( (36) (44) (5) Torque Nm (in.lb.) Power kw (hp) Power kw (hp) 48 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Performance Quiet version, optimized for 1-18 rpm (E) PVM74 Torque Nm (in.lb.) Torque Nm (in.lb.) Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Delivery and Efficiency at 15 r/min Volumetric 5 C Efficiency (12 F) and 1. absolute ( psi gauge) Inlet 9 1 8 7 6 Volumetric Efficiency 9 8 7 5 6 125 (33) 4 5 1125 (26)(33) 3 2 1 4 3 2 75 (2) 1 (26) 5 (13) 75 (2) 25 (7) 5 (13) 1 25 (7) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 Outlet 1 Pressure 15 2 ( 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque and Power at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 4 (354) Torque and Power at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 36 (3186) 4 (354) 32 (2832) Torque, 36 (3186) 28 (2478) 32 (2832) Torque, 24 (2124) 28 (2478) 2 (177) 24 (2124) 16 (1416) 2 (177) Power, 8 (17) 12 (162) 16 (1416) Power, 6 (8) (17) 8 (78) 12 (162) 4 (54) 6 (8) 4 (354) 8 (78) 2 (27) 4 (54) 4 (354) 2 (27) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 Outlet 1 Pressure 15 2 ( 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque Nm (in.lb.) Power kw (hp) Power kw (hp) Delivery and Efficiency at 12 r/min 1 5 C (12 F) and 1. absolute ( psi gauge) Inlet Delivery and Efficiency at 12 r/min 5 C (12 F) and 1. absolute Volumetric ( psi gauge) Efficiency Inlet 9 8 7 6 5 4 1 9 8 7 6 5 Volumetric Efficiency 125 (33) 1 (26) 125 (33) 3 2 1 4 3 2 75 (2) 5 (13) 25 (7) 1 (26) 75 (2) 5 (13) 1 25 (7) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 Outlet Pressure 1 15 ( 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque and Power at 12 r/min 4 (354) 5 C (12 F) and 1. absolute ( psi gauge) Inlet Torque and Power at 12 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 36 (3186) 4 (354) 32 (2832) 36 (3186) Torque, Torque, 28 (2478) 32 (2832) 24 (2124) 28 (2478) 2 (177) 24 (2124) 16 (1416) 2 (177) 8 (17) 12 (162) 16 (1416) Power, 6 (8) 8 (17) Power, 8 (78) 12 (162) 4 (54) 6 (8) 4 (354) 8 (78) 2 (27) 4 (54) 4 (354) 2 (27) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 Outlet Pressure 1 15 ( 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque Nm (in.lb.) Power kw (hp) Power kw (hp) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 49
Performance Quiet version, optimized for 1-18 rpm (E) PVM74 Torque Nm (in.lb.) Torque and Power at 1 r/min 5 C (12 F) and Torque 1. and absolute Power ( psi at gauge) 1 Inlet r/min 4 (354) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 4 (354) 36 (3186) 36 (3186) 32 (2832) 32 (2832) 28 (2478) 28 (2478) 24 (2124) 24 (2124) 2 (177) 2 (177) 16 (1416) 16 (1416) 12 (162) 12 (162) 8 (78) 8 (78) 4 (354) Torque Nm (in.lb.) Delivery and Efficiency at 1 r/min 5 C (12 F) Delivery and 1. and Efficiency absolute ( psi at gauge) 1 Inlet r/min 1 5 C (12 F) and 1. absolute Volumetric ( psi Efficiency gauge) Inlet 1 9 Volumetric Efficiency 9 8 7 6 5 4 8 7 6 5 1 (26) 4 1 (26) 3 75 (2) 3 75 (2) 2 5 (13) 1 2 5 (13) 25 (7) 1 25 (7) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 1 15 2 25 3 35 (7) Outlet (15) Pressure (22) (29) ( (36) (44) (5) Torque, Torque, Power, Power, 4 (354) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) 5 1 15 2 25 (7) Outlet (15) Pressure (22) (29) ( (36) 8 (17) 8 (17) 6 (8) 6 (8) 4 (54) 4 (54) 2 (27) 2 (27) 35 (5) 3 (44) 35 (5) Power kw (hp) Power kw (hp) Case Flow Case - l/min Flow (USgpm) - l/min (USgpm) Case Flow - l/min (USgpm) Case Flow - l/min (USgpm) Case Flow Versus Outlet Pressure at Full Flow, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 5, (1.32) Case Flow Versus Outlet Pressure at Full Flow, 18 r/min 4,5 (1.19) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 5, (1.32) 4, (1.6) 3,5 4,5 (.92) (1.19) 3, 4, (.79) (1.6) 2,5 3,5 (.66) (.92) 2, 3, (.53) (.79) 1,5 2,5 (.4) (.66) 1, 2, (.26) (.53),5 1,5 (.13) (.4) 1, (.26) 5 1 15 2 25 3 35,5 (.13) (7) (15) (22) (29) (36) (44) (5) 5 1 15 2 25 3 35 Case Flow (7) Versus (15) Outlet (22) Pressure (29) at Cutoff, (36) 18 (44) r/min (5) 5 C (12 F) and Outlet 1. Pressure absolute ( ( gauge) Inlet 12 (3.17) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1112 (2.91) (3.17) 11 (2.91) 1 (2.64) 9 1 (2.38) (2.64) 8 9 (2.11) (2.38) 8 (2.11) 7 (1.85) 5 1 (7) (15) 15 (22) 2 (29) 25 (36) 7 (1.85) Outlet Pressure - ( 5 1 15 2 (7) (15) (22) (29) Outlet Pressure - ( 25 (36) 3 (44) 3 (44) 35 (5) 35 (5) 5 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Torque Nm (in.lb.) Performance Higher speed version (M) PVM74 Noise Level dba Efficiency % 84 84 8 8 76 76 72 72 68 68 64 64 6 6 56 56 52 52 5 5 1 1 15 15 2 2 (7) (7) (15) (15) (22) (22) (29) (29) Outlet Outlet Pressure Pressure ( ( 95 95 24 24 r/min r/min Min. Min. Flow Flow Typical Typical Noise Noise Levels Levels Petroleum Petroleum Oil Oil (1W) (1W) at at 93 C 93 C (2 F), (2 F), 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet (Sound (Sound pressure pressure data data equivalent equivalent to to NFPA) NFPA) 24 24 r/min r/min Max. Max. Flow Flow 6 6 r/min r/min Min. Min. Flow Flow 6 6 r/min r/min Max. Max. Flow Flow 25 25 (36) (36) Overall Efficiency Versus Versus Speed Speed at at 93 C 93 C (2 F) (2 F) and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 3 3 (44) (44) 9 9 5 5 (7 (7 85 85 1 1 (15 (15 15 8 8 15 (22 (22 2 75 2 75 (29 (29 25 25 7 7 (36 (36 28 28 (4 65 (4 65 32 32 (46 (46 6 6 5 5 1 1 15 15 2 2 25 25 Speed Speed r/min r/min Power @ Full Flow kw (hp) Delivery and Case Flow Versus Speed @ 93 C (2 F), full flow and 1. absolute ( gauge Inlet 18 (48) 16 (42) 5 (7, Delivery 14 (37) 12 (32) 1 (26) 28 (4, Delivery 8 (21) 6 (16) 28 (4, Case flow 8 (2.1) 6 (1.6) 4 (11) 4 (1.1) 2 (5) 5 (7, Case flow 2 (.5) 5 1 15 2 25 4 (354) 35 (397) 3 (2655) 25 (2212) 2 (177) 15 (1327) 1 (885) 5 (442) 1 (134) 9 (121) 8 (17) 7 (94) 6 (8) 5 (67) 4 (54) 3 (4) 2 (27) 1 (13) Speed r/min Torque Versus Speed @ 93 C (2 F), full flow and 1. absolute ( psi gauge) inlet 32 (46 28 (4 25 (36 2 (29 15 (22 1 (15 5 (7 17 (25 5 1 15 2 25 Speed r/min Power Versus Speed 93 C (2 F), 1. absolute ( psi gauge) Inlet 32 (46) 28 (4) 25 (36) 2 (29) 15 (22) 1 (15) 5 (7) 17 (25) 5 1 15 2 25 Speed r/min Case Flow l/min (USgpm) Pressure ( Pressure ( EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 51
Torque Torque Nm Nm (in.lb.) (in.lb.) Case Case Flow Flow l/min l/min (USgpm) (USgpm) Case Case Flow Flow l/min l/min (USgpm) (USgpm) Performance Higher speed version (M) PVM74 7 (62) (62) Torque Torque and and Case Case Flow Flow Versus Versus Speed Speed @ 93 C 93 C (2 F), (2 F), load load sense sense standby standby and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) inlet inlet 2 2 (3 (3 differential, differential, Torque Torque 6 (53) (53) 5 (44) (44) 4 (35) (35) 3 (27) (27) 2 (18) (18) 11 11 (16) (16) differential differential Torque Torque 2 2 (3 (3 differential differential Case Case Flow Flow 8. 8. (2.11) (2.11) 6. 6. (1.58) (1.58) 4. 4. (1.6) (1.6) 1 (9) (9) 2. 2. (.53) (.53) 11 11 (16 (16 differential differential Case Case Flow Flow 5 5 1 1 15 15 2 2 25 25 Speed Speed r/min r/min 16 16 (1416) (1416) 14 14 (1239) (1239) Torque Torque and and Case Case Flow Flow Versus Versus Speed Speed @ 93 C 93 C (2 F), (2 F), cut-off cut-off and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) inlet inlet 28 28 (4 (4,, Torque Torque Torque Nm (in.lb.) 12 12 (162) (162) 1 1 (885) (885) 8 8 (78) (78) 15 15 (22 (22,, Torque Torque 6 6 (531) (531) 3 3 (7.9) (7.9) 28 28 (4 (4,, Case Case Flow Flow 4 4 (354) (354) 2 2 (5.3) (5.3) 2 2 (177) (177) 1 1 (2.6) (2.6) 15 15 (22 (22,, Case Case Flow Flow 5 5 1 1 15 15 2 2 25 25 Speed Speed r/min r/min 52 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Performance Quiet version, optimized for 1-18 rpm (E) PVM81 Noise Noise Level Level dba dba Typical Noise Levels at 18 and 12 r/min. with Petroleum Oil (1W) at 5 C (12 F) Typical and Noise 1. Levels absolute at 18 ( and psi 12 gauge) r/min. Inletwith 74 Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 18 r/min 74 min. flow 72 18 r/min 18 r/min min. flow 727 max. flow 18 r/min 7 68 max. flow 68 12 r/min 66 max. flow 12 r/min 66 64 max. flow 6462 626 6 58 5 (7) 58 5 (7) 12 r/min min. flow 12 r/min min. flow 1 15 2 (15) (22) (29) Outlet 1Pressure 15 ( 2 (15) (22) (29) 25 (36) 25 (36) Delivery and Efficiency at 18 r/min, 5C (12F), and 1. absolute ( psi gauge) Inlet Delivery 1 and Efficiency at 18 r/min, 5C (12F), and Volumetric 1. Efficiency absolute ( psi gauge) Inlet 1 9 Volumetric Efficiency 8 9 7 8 Efficiency % 6 7 5 6 4 5 3 4 2 3 1 2 1 5 1 15 2 (7) (15) (22) (29) 5 Outlet 1 Pressure 15 ( 2 (7) (15) (22) (29) 15 (4) 125 15 (33) (4) 1 125 (26) (33) 75 1 (2) (26) 5 75 (13) (2) 25 5 (7) (13) 25 (7) 25 (36) 25 (36) Delivery Delivery l/min l/min (USgpm) (USgpm) Del De 1 1 9 89 78 Efficiency % 67 56 45 34 23 12 1 Noise Noise Level Level dba dba Typical Noise Levels at 15 and 1 r/min. with Petroleum Oil (1W) at 5 C (12 F) Typical and Noise 1. Levels absolute at 15 ( and psi 1 gauge) r/min. Inletwith 72 Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 727 768 6866 664 6462 626 658 1 r/min min. flow 1 r/min min. flow 15 r/min max. flow 15 r/min max. flow 1 r/min max. flow 1 r/min max. flow 15 r/min min. flow 15 r/min min. flow 5856 5 1 15 2 56 (7) (15) (22) (29) 5 Outlet 1Pressure 15 ( 2 Sound pressure (7) data(15) (22) (29) equivalent to NFPA. Sound pressure data equivalent to NFPA. 25 (36) 25 (36) Torque Torque Nm (in.lb.) Nm (in.lb.) Torque and Power at 18 r/min, 5C (12F), and 1. absolute ( psi gauge) Inlet Torque and Power at 18 r/min, 5C (12F), 35 (397) and 1. absolute ( psi gauge) Inlet 35 (397) 3 (2655) 3 (2655) 25 (2212) 25 (2212) 2 (177) Torque, Torque, Power Power kw (hp) kw (hp) 2 (177) 15 (1327) 75 (11) Power, 15 (1327) 75 (11) 1 (885) Power, 5 (67) 1 (885) 5 (67) 5 (442) Torque, 25 (34) Cut-off 5 (442) Torque, 25 (34) Cut-off 5 1 15 2 25 (7) (15) (22) (29) (36) 5 Outlet 1 (7) (15) Pressure 15 ( 2 25 (22) (29) (36) Torque Torque Nm (in.lb.) Nm (in.lb.) In In EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 53
Performance Quiet version, optimized for 1-18 rpm (E) PVM81 Delivery Delivery l/min l/min (USgpm) (USgpm) Delivery and Efficiency at 15 r/min, 5C (12F), and 1. absolute ( psi gauge) Inlet Delivery 1 and Efficiency at 15 r/min, 5C (12F), and 1. absolute ( psi gauge) Inlet Volumetric Efficiency 1 9 Volumetric Efficiency 8 9 7 8 Efficiency % 6 7 5 6 4 5 3 4 2 3 1 2 1 5 1 15 2 (7) (15) (22) (29) 5 1 15 2 (7) Outlet (15) Pressure (22) ((29) 125 (33) 1 125 (26) (33) 75 1 (2) (26) 5 75 (13) (2) 25 5 (7) (13) 25 (7) 25 (36) 25 (36) Delivery Delivery l/min l/min (USgpm) (USgpm) Efficiency % Delivery and Efficiency at 12 r/min, 5C (12F), Delivery and and 1. Efficiency absolute at 12 ( psi r/min, gauge) 5C Inlet (12F), and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency 9 Volumetric Efficiency 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 5 1 15 2 (7) 5 (15) 1 (22) 15 (29) 2 (7) Outlet (15) Pressure (22) ( (29) (36) 25 (36) Delivery Delivery l/min l/min (USgpm) (USgpm) 125 (33) 125 (33) 1 (26) 1 (26) 75 (2) 75 (2) 5 (13) 5 (13) 25 (7) 25 (7) 25 Efficiency % Del Deli 1 1 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 Torque Torque Nm (in.lb.) Nm (in.lb.) Torque and Power at 15 r/min, 5C (12F), and 1. absolute ( psi gauge) Inlet Torque and Power at 15 r/min, 5C (12F), 35 and (397) 1. absolute ( psi gauge) Inlet 35 (397) 3 (2655) 3 (2655) 25 (2212) 25 (2212) 2 (177) 2 (177) 15 (1327) 15 (1327) 1 (885) Torque, Torque, 1 (885) 5 (442) Power, 5 (442) Power, 5 1 Full 15Stroke2 (7) (15) (22) (29) 5 1 15 2 (7) Outlet (15) Pressure (22) ( (29) Power Power kw (hp) kw (hp) 75 (11) 75 (11) 5 (67) 5 (67) 25 (34) 25 (34) 25 (36) 25 (36) Torque Torque Nm Nm (in.lb.) (in.lb.) Torque and Power at 12 r/min, 5C (12F), Torque and 1. and Power absolute at 12 ( psi r/min, gauge) 5C Inlet (12F), 35 (397) and 1. absolute ( psi gauge) Inlet 35 (397) 3 (2655) 3 (2655) 25 (2212) Torque, 25 (2212) Torque, 2 (177) 2 (177) 15 (1327) 75 (11) 15 (1327) 75 (11) 1 (885) 5 (67) Power, 1 (885) 5 (67) Power, 5 (442) 25 (34) 5 (442) 25 (34) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) (29) ( (36) Power Power kw kw (hp) (hp) Torque Torque Nm Nm (in.lb.) (in.lb.) In In 3 3 2 2 1 54 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Performance Quiet version, optimized for 1-18 rpm (E) PVM81 2F), 12F), t Delivery Delivery l/min l/min (USgpm) (USgpm) 125 (33) 125 (33) 1 (26) 1 (26) 75 (2) 75 (2) 5 (13) 5 (13) 25 (7) 25 (7) 5 ) ) Efficiency Efficiency % % Delivery and Efficiency at 1 r/min, 5C (12F), Delivery and 1. and Efficiency absolute at ( 1 psi r/min, gauge) 5C Inlet (12F), and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 1 9 Volumetric Efficiency 9 8 8 7 7 6 6 5 125 (33) 5 125 (33) 4 1 (26) 4 1 (26) 3 75 (2) 3 75 (2) 2 5 (13) 2 5 (13) 1 25 (7) 1 25 (7) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) Delivery Delivery l/min l/min (USgpm) (USgpm) Case Flow l/min - (USgpm) 4. (1.6) 3.5 (.92) 3. (.79) 2.5 (.66) 2. (.53) 1.5 (.4) 1. (.26).5 (.13) Case Flow versus Outlet Pressure at 18 r/min, Full Flow, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 5 (7) 1 15 (15) (22) Outlet Pressure - ( 2 (29) 25 (36) 12F), t(12f), t Power Power kw kw (hp) (hp) 75 (11) 75 (11) 5 (67) 5 (67) 25 (34) 25 (34) ) ) Torque Torque Nm Nm (in.lb.) (in.lb.) Torque and Power at 1 r/min, 5C (12F), and Torque 1. and absolute Power at (1 psi gauge) r/min, 5C Inlet(12F), 35 (397) and 1. absolute ( psi gauge) Inlet 35 (397) 3 (2655) 3 (2655) 25 (2212) 25 (2212) Torque, Full Stroke 2 (177) Torque, 2 (177) 15 (1327) 75 (11) 15 (1327) 75 (11) 1 (885) 5 (67) 1 (885) Power, 5 (67) 5 (442) Full Stroke Power, 25 (34) 5 (442) 25 (34) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) Power Power kw kw (hp) (hp) Case Flow l/min - (USgpm) 21 (5.55) 2 (5.28) 19 (5.2) 18 (4.76) 17 (4.49) 16 (4.23) 15 (3.96) 14 (3.7) 13 (3.43) 12 (3.17) 11 (2.91) Case Flow versus Outlet Pressure at Cutoff, 18 r/min, 5 C (12 F), and 1. absolute ( psi gauge) Inlet 5 (7) 1 15 (15) (22) Outlet Pressure - ( 2 (29) 25 (36) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 55
Delivery Delivery l/min l/min (USgpm) (USgpm) Performance Higher speed version (M) PVM81 Typical Noise Levels at 24 & 6 r/min with Petroleum Oil (1W) at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 82 24 r/min max. flow Noise Level dba 78 74 7 66 62 58 6 r/min max. flow 24 r/min min. flow Noise Level dba 7 54 5 1 15 2 (7) (15) (22) (29) 66 Sound pressure data equivalent to to NFPA. 62 82 78 6 r/min 74 min. flow 58 Typical Noise Levels at 24 & 6 r/min with Petroleum Oil (1W) at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 25 (36) 24 r/min max. flow 6 r/min max. flow 24 r/min min. flow 6 r/min min. flow 54 5 1 15 (7) (15) (22) Sound pressure data equivalent to NFPA. 2 (29) 25 (36) versus Speed at 93 C (2 F) and 1. absolute ( psi gauge) inlet Delivery and Case Flow versus Speed at 93 C (2 F), Full Flow 1. absolute ( psi gauge) Inlet (%) 1 95 9 85 15 (22 1 (145 5 (725 8 75 23 (33 1 7 2 (29 65 95 9 6 85 55 8 5 5 1 15 2 25 75 Speed r/min 7 65 23 (33 3 2 (29 56 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 (%) 6 55 5 2 (53) 18 (48) 16 (42) 14 (37) versus Speed 5 (725 Delivery and Case Flo at 93 C (2 F) and 1. absolute Delivery at 93 C (2 F), Full Flow ( psi 12 gauge) (32) inlet 21 (3 Case Flow ( psi gauge Delivery l/min 1 1 (26) 2 (53) (USgpm) (145 8 (21) 5 (725 21 (3 Case Flow 18 (48) 8 (2.11) 6 (16) 16 (42) 6 (1.59) 4 (11) 14 (37) 4 (1.6) 5 (725 Delivery 2 (5) 5 (725 Case Flow 12 (32) 2 (.53) 15 (22 5 1 15 2 25 Speed r/min 1 (26) 5 1 15 2 25 3 8 (21) Speed (r/min) 6 (16) 3 4 (11) 2 (5) 5 (725 21 (3 5 1 15 Speed (r/mi
Performance Higher speed version (M) PVM81 Torque Nm Torque (in.lb.) Nm (in.lb.) Torque versus Speed at 93 C (2 F), Full Flow and 1. absolute ( psi gauge) Inlet 35 (2655) Torque versus Speed at 93 C (2 F), Full Flow and 1. absolute ( psi gauge) Inlet 3 (2655) 23 35 (2655) (33 25 3 (2212) 21 (2655) (3 23 (33 25 2 (2212) (177) 21 15 (3 (22 2 15 (177) (1327) 15 1 (22 (15 15 1 (1327) (885) 1 5 (15 (725 1 5 (885) (442) 17 (25 5 (725 5 (442) 5 1 15 2 25 3 17 (25 Speed (r/min) 5 1 15 2 25 3 Speed (r/min) Power Power Power kw kw Power (hp) (hp) kw kw (hp) (hp) Power versus Speed at 93 C (2 F), Full Flow and 1. absolute ( psi gauge) Inlet 1 Power versus Speed at 93 C (2 F), (134) Full Flow and 1. absolute ( psi gauge) Inlet 9 (121) 1 (134) 8 (17) 23 9 (121) (33 7 (94) 2 (29 8 6 (17) (8) 23 (33 7 5 (94) (67) 2 15 (29 (22 6 4 (8) (54) 5 (67) 15 1 (22 (15 3 (4) 4 (54) 2 (27) 1 5 (725 (15 3 (4) 1 (13) 17 (25 2 (27) 5 (725 1 (13) 5 1 15 2 25 3 17 (25 Speed (r/min) 5 1 15 2 25 3 Speed (r/min) Torque Nm Torque (in.lb.) Nm (in.lb.) Torque and Case Flow versus Speed at 93 C (2 F), Load Sense Standby and 1. absolute ( psi gauge) Inlet Torque and Case Flow versus Speed at 93 C 9 (8) (2 F), Load Sense Standby and 1. absolute 2 (3 ( psi gauge) Inlet 8 (71) diff. Torque 9 (8) 7 (62) 2 (3 8 (71) diff. Torque 11 (16 diff. 6 (53) Torque Case 7 (62) Flow l/min 5 (44) (USgpm) 11 (16 diff. 6 (53) Torque Case 4 (35) 1. Flow (2.64) l/min 5 (44) (USgpm) 2 (3 3 (27) 8. (2.11) diff. 4 (35) Case Flow 1. (2.64) 2 (18) 6. (1.59) 2 (3 11 (16 diff. 3 (27) Case 8. (2.11) diff. Case Flow Flow 1 (9) 4. (1.6) 2 (18) 6. (1.59) 11 (16 diff. 2. (.53) Case Flow 1 (9) 5 1 15 2 25 3 4. (1.6) Speed (r/min) 2. (.53) 5 1 15 2 25 3 Speed (r/min) Torque Nm Torque (in.lb.) Nm (in.lb.) Torque and Case Flow versus Speed at 93 C (2 F), Pressure Limit Cut-off and 1. absolute ( psi gauge) Inlet Torque and Case Flow versus Speed at 93 C 8 (2 F), (78) Pressure Limit Cut-off and 1. absolute ( psi gauge) Inlet 7 (619) 8 (78) 21 (3 Torque 15 6 (531) (22 7 (619) 21 (3 Torque 5 (442) 15 Torque 6 (531) (22 4 (354) 5 (442) Torque 21 (3 3 (265) Case 8. (2.11) 4 (354) 21 Flow 2 (177) 6. (3 (1.59) 3 (265) Case 8. (2.11) 15 Flow 4. (1.6) 1 (88) 2 (177) (22 6. (1.59) 2. (.53) Case Flow 15 4. (1.6) 1 (88) 5 (22 1 15 2 25 3 2. (.53) Case Flow Speed (r/min) 5 1 15 2 25 3 Speed (r/min) Case Flow Case l/min Flow (USgpm) l/min (USgpm) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 57
Performance Quiet version, optimized for 1-18 rpm (E) PVM98 Noise Level dba Noise Level dba Noise Level dba Noise Level dba Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet 78 18 r/min 76 Max. Flow Typical Noise Levels at 18 and 12 r/min 74 with Petroleum Oil (1W) at 5 C (12 F) 18 r/min Min. Flow and 1. absolute ( psi gauge) Inlet 7872 18 r/min 12 r/min 767Max. Flow Max. Flow 7468 18 r/min Min. Flow 7266 12 r/min 764 Max. Flow 6862 Delivery and Efficiency at 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 9 8 Volumetric Efficiency Delivery and Efficiency at 18 r/min 5 C (12 F) and Overall 1. Efficiency absolute ( psi gauge) Inlet 1 7 9 Volumetric Efficiency 6 8 5 4 666 3 5 15 (4) 6458 12 r/min Min. Flow 2 4 1 (26) 2 (53) 6256 5 1 15 2 25 3 6 (7) (15) (22) (29) (36) (44) 1 3 5 (13) 15 (4) 58 Sound pressure 12 datar/min 2 1 (26) equivalent to NFPA) Min. Flow 56 5 1 15 2 25 3 35 5 1 15 2 25 3 1 (7) (15) (22) (29) (36) (44) (5) 5 (13) (7) (15) (22) (29) (36) (44) Outlet Pressure - ( Typical Noise Outlet Levels Pressure at 15 ( and 1 r/min Sound pressure with data Petroleum Oil (1W) at 5 C (12 F) 5 1 15 2 25 3 35 equivalent to and NFPA) 1. absolute ( psi gauge) Inlet Torque (7) and (15) Power (22) at 18 (29) r/min (36) (44) (5) 72 5 C (12 F) and 1. absolute ( psi gauge) Inlet Outlet Pressure - ( 15 r/min 55 (4867) 7Typical Max. Noise Flow Levels at 15 and 1 r/min with Petroleum Oil (1W) at 5 C (12 F) 5 (4425) Torque and Power at 18 r/min 68 and 1. absolute ( psi gauge) Inlet 5 C (12 F) and 1. Torque, absolute ( psi gauge) Inlet 72 15 r/min 66 45 (3982) 55 (4867) Min. Flow 15 r/min 7 64 Max. Flow 1 r/min 4 (354) 5 (4425) Max. Flow 68 62 35 (397) Torque, 45 (3982) 15 r/min 66 6 Min. Flow 3 (2655) 4 (354) 64 1 r/min 58 Max. Flow 25 (2212) 35 (397) Power, 62 56 2 (177) 3 (2655) 1 (134) 6 54 1 r/min Min. Flow 15 (1327) 25 (2212) Power, 75 (11) 5852 5 1 15 2 25 3 1 (885) 2 (177) 5 (67) 1 (134) 56 (7) (15) (22) (29) (36) (44) 5 (442) Torque, 25 (34) 54 1 r/min 15 (1327) 75 (11) Min. Flow Cut-off 52 1 (885) 5 1 15 2 25 3 35 5 (67) 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) (7) (15) (22) (29) (36) (44) (5) 5 (442) Outlet Pressure - ( Torque, 25 (34) Cut-off 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Outlet Pressure - ( Torque - Nm (in.lb.) Torque - Nm (in.lb.) Efficiency - % Efficiency - % 7 6 2 (53) Delivery -l/min (USgpm) Power - kw (hp) Delivery -l/min (USgpm) Power - kw (hp) 58 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Performance Quiet version, optimized for 1-18 rpm (E) PVM98 Torque Nm (in.lb.) Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Volumetric Efficiency 9 Delivery and Efficiency at 15 r/min 5 C (12 F) and Overall 1. Efficiency absolute ( psi gauge) Inlet 8 1 Volumetric Efficiency 7 6 9 8 5 4 3 2 1 2 (53) 15 (4) 1 (26) 2 (53) 5 (13) 15 (4) 2 1 (26) 5 1 15 2 25 3 35 1(7) (15) (22) (29) (36) (44) (5) 5 (13) Torque 5 1 and Power 15 at 21525 r/min3 35 (7) (15) (22) (29) (36) (44) (5) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 55 (4867) 5 (4425) Torque and Power at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 45 (3982) 55 (4867) Torque, 4 (354) 5 (4425) 35 (397) 45 (3982) 3 (2655) 4 (354) Torque, 25 (2212) 35 (397) 2 (177) Power, 1 (134) 3 (2655) 15 (1327) 75 (11) 25 (2212) 1 (885) 2 (177) 5 (442) 15 (1327) Power, 5 (67) 1 (134) 25 (34) 75 (11) 1 (885) 5 (67) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 (442) 25 (34) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque Nm (in.lb.) 7 6 5 4 3 Torque Nm (in.lb.) Power kw (hp) Power kw (hp) Delivery and Efficiency at 12 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 9 Volumetric Efficiency Delivery and Efficiency at 12 r/min 5 C (12 F) Overall and 1. Efficiency absolute ( psi gauge) Inlet 8 1 7 9 Volumetric Efficiency 6 8 5 7 4 6 2 (53) 3 5 15 (4) 2 4 1 (26) 2 (53) 1 3 5 (13) 15 (4) 2 1 (26) 5 1 15 2 25 3 35 1(7) (15) (22) (29) (36) (44) (5) 5 (13) 5 1 15 2 25 3 35 (7) Torque (15) and Power (22) (29) at 12 (36) r/min(44) (5) 5 C (12 F) and 1. Outlet absolute Pressure ( psi ( gauge) Inlet 55 (4867) 5 (4425) Torque and Power at 12 r/min 45 (3982) 55 (4867) 5 C (12 F) and 1. absolute ( psi gauge) Inlet Torque, 4 (354) 5 (4425) 35 (397) 45 (3982) Torque, 3 (2655) 4 (354) 25 (2212) 35 (397) 2 (177) 3 (2655) 1 (134) Power, 15 (1327) 75 (11) 25 (2212) 1 (885) 2 (177) 5 (442) 15 (1327) Power, 5 (67) 1 (134) 25 (34) 75 (11) 1 (885) 5 (67) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 (442) 25 (34) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque Nm (in.lb.) Power kw (hp) Power kw (hp) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 59
Performance Quiet version, optimized for 1-18 rpm (E) PVM98 Torque Nm (in.lb.) Delivery and Efficiency at 1 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 Volumetric Delivery Efficiency and Efficiency at 1 r/min 9 5 C (12 F) Overall and 1. Efficiency absolute ( psi gauge) Inlet 1 8 Volumetric Efficiency 7 6 5 9 8 7 4 6 2 (53) 5 3 15 (4) 4 2 (53) 2 1 (26) 1 3 15 (4) 5 (13) 2 1 (26) 5 1 15 2 25 3 35 1 (7) (15) (22) (29) (36) (44) (5) 5 (13) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque and Outlet Power Pressure at 1 ( r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 55 (4867) 5 (4425) Torque and Power at 1 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 45 (3982) 55 (4867) 4 (354) 5 (4425) 35 (397) 45 (3982) 3 (2655) 4 (354) 25 (2212) 35 (397) 2 (177) 3 (2655) 1 (134) 15 (1327) 25 (2212) 75 (11) Power, 1 (885) 2 (177) 5 (67) 1 (134) 5 (442) 15 (1327) Power, 25 (34) 75 (11) 1 (885) 5 (67) 5 1 15 2 25 3 35 5 (442) (7) (15) (22) (29) (36) (44) (5) 25 (34) Outlet Pressure - ( 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Outlet Pressure - ( Torque Nm (in.lb.) Torque, Torque, Power kw (hp) Power kw (hp) Case Flow - l/min Case Flow (USgpm) - l/min (USgpm) Case Flow - l/min Case Flow (USgpm) - l/min (USgpm) Case Flow Versus Outlet Pressure at Full Flow, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 5,5 (1.45) Case 5, (1.32) Flow Versus Outlet Pressure at Full Flow, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 4,5 (1.19) 5,5 (1.45) 4, (1.6) 5, (1.32) 3,5 (.92) 4,5 (1.19) 3, (.79) 4, (1.6) 2,5 (.66) 3,5 (.92) 2, (.53) 3, (.79) 1,5 (.4) 2,5 (.66) 1, (.26) 2, (.53),5 (.13) 1,5 (.4) 1, (.26) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5),5 (.13) Outlet Pressure - ( Case Flow 5 Versus 1 Outlet 15 Pressure 2 at 25Cutoff, 31835 r/min (7) 5 C (12 (15) F) and (22) 1. (29) absolute (36) ( psi gauge) (44) Inlet (5) 25 (6.6) Outlet Pressure - ( 24 (6.34) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 25 (6.6) 23 (6.8) 24 (6.34) 22 (5.81) 23 (6.8) 21 (5.55) 22 (5.81) 2 (5.28) 21 (5.55) 19 (5.2) 2 (5.28) 18 (4.76) 19 (5.2) 17 (4.49) 5 1 15 2 25 3 35 18 (4.76) (7) (15) (22) (29) (36) (44) (5) Outlet Pressure - ( 17 (4.49) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Outlet Pressure - ( 6 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Overall Efficiency (%) (%) Torque Nm (in.lb.) Torque Nm (in.lb.) Performance Higher speed version (M) PVM98 Noise Noise Level Level dba dba 86 86 84 84 82 82 8 8 78 78 76 76 74 74 72 72 7 7 68 68 66 Typical Noise Levels at 2 and 6 r/min with petroleum oil (1 W) @ 93 C (2 F) Typical Noise Levels at 2 and 6 r/min and 1. absolute ( psi gauge) inlet with petroleum oil (1 W) @ 93 C (2 F) and 1. absolute ( psi gauge) inlet 6 r/min Min. flow 6 r/min Min. flow 2 r/min Min. flow 2 r/min Min. flow 664 5 1 15 2 64 (7) (15) (22) (29) 5 Outlet 1Pressure 15 ( 2 (7) (15) (22) (29) Sound pressure data equivalent Outlet to NFP Pressure ( Sound pressure data equivalent to NFP 2 r/min Max. flow 2 r/min Max. flow 6 r/min Max. flow 6 r/min Max. flow 25 (36) 25 (36) 3 (44) 3 (44) Delivery and Case Flow Versus Speed Delivery and @ Case 93 C (2 F), Flow Versus full flow Speed and @ 93 C 1. (2 F), absolute full flow ( and gauge Inlet 22 (58) 1. absolute ( gauge Inlet 22 (58) 2 (53) 5 (7, 2 (53) 5 Delivery (7, 18 (48) Delivery 18 (48) 16 (42) 16 (42) 14 (37) 28 (4, Delivery 14 (37) 28 (4, 12 (32) Delivery 12 (32) 1 (26) 1 (26) 28 (4, 8 (21) 28 Case (4 flow, 8 (2.1) 8 (21) Case flow 8 (2.1) 6 (16) 6 (1.6) 6 (16) 6 (1.6) 4 (11) 5 (7, 4 (1.1) 4 (11) 5 Case (7 flow, 4 (1.1) 2 (5) Case flow 2 (.5) 2 (5) 2 (.5) 5 1 15 2 25 5 1 Speed 15 r/min 2 25 Speed r/min Case Flow l/min (USgpm) Case Flow l/min (USgpm) 95 95 9 9 Versus Speed @ 93 C (2 F) and 1. absolute Versus Speed ( psi gauge) inlet @ 93 C (2 F) and 1. absolute ( psi gauge) inlet 85 1 (15 1 15 (15 (22 85 15 (22 5 (7 2 (29 8 5 (7 2 (29 8 25 (36 75 25 28 (36 (4 75 28 32 (4 (46 7 32 (46 5 1 15 2 25 7 Speed r/min 5 1 15 2 25 Speed r/min Torque Versus Speed Torque @ 93 C Versus (2 F), full Speed flow and @ 93 C 1. (2 F), absolute full flow ( psi and gauge) inlet 6 (531) 1. absolute ( psi gauge) inlet 6 (531) 54 (4779) 54 (4779) 32 (46 48 (4248) 32 (46 48 (4248) 28 (4 42 (3717) 28 (4 25 (36 42 (3717) 36 (3186) 25 (36 36 (3186) 2 (29 3 (2655) 2 (29 3 (2655) 24 (2124) 15 (22 24 (2124) 15 (22 18 (1593) 18 (1593) 12 (162) 12 (162) 1 (15 1 (15 5 (7 6 (531) 5 (7 17 (25 6 (531) 17 (25 5 1 15 2 25 3 5 1 15 Speed 2 r/min 25 3 Speed r/min EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 61
Power Power KW KW (hp) (hp) Torque Torque Nm Nm (in.lb.) (in.lb.) Case Flow l/min (USgpm) Performance Higher speed version (M) PVM98 Power Versus Speed @93 C Power (2 F), Versus full flow Speed and 1. @93 C absolute (2 F), ( psi full gauge) flow and inlet 13 (174) 1. absolute ( psi gauge) inlet 13 (174) 12 (161) 32 (46 12 (161) 11 (148) 32 (46 11 (148) 1 (134) 28 (4 1 (134) 28 (4 25 (36 9 (121) 25 (36 9 (121) 8 (17) 8 (17) 2 (29 7 (94) 2 (29 7 (94) 6 (8) 6 (8) 15 (22 5 (67) 15 (22 5 (67) 4 (54) 1 (15 4 (54) 3 (4) 1 (15 3 (4) 2 (27) 5 (7 2 (27) 5 (7 1 (13) 17 (25 1 (13) 17 (25 5 1 15 2 25 3 5 1 15 2 25 3 Speed r/min Speed r/min Torque and Case Flow Versus Speed Torque @ 93 C (2 F), and Case load sense Flow standby Versus Speed and @ 1. 93 C (2 F), absolute load ( psi sense gauge) standby inlet 11 (77) and 1. absolute ( psi gauge) inlet 11 (77) 1 (88) 2 (3) differential 1 (88) 2 Torque (3) differential Torque 9 (8) 9 (8) 8 (71) 8 (71) 11 (16) differential 9. (2.38) 7 (62) 11 (16) differential 9. (2.38) 7 (62) Torque Torque 8.5 (2.25) 6 (53) 8.5 (2.25) 6 (53) 8. (2.11) 5 (44) 2 (3) differential 8. (2.11) 5 (44) Case 2 Flow (3) differential 7.5 (1.98) 4 (35) Case Flow 7.5 (1.98) 4 (35) 7. (1.85) 7. (1.85) 3 (27) 6.5 (1.72) 3 (27) 11 (16) differential 6.5 (1.72) 2 (18) Case 11 Flow (16) differential 6. (1.59) 2 (18) Case Flow 6. (1.59) 1 (9) 5.5 (1.45) 1 (9) 5 1 15 2 25 5.5 (1.45) 5 Speed 1 r/min 15 2 25 Speed r/min Torque Nm (lb.in.) Case Case Flow Flow (l/min (l/min (USgpm) (USgpm) Case Flow l/min (USgpm) Torque and Case Flow Versus Speed @ 93 C (2 F), cut-off and 1. absolute ( psi gauge) inlet 24 (2124) 22 (1947) 28 (4 Torque 2 (177) 18 (1593) 16 (1416) 14 (1239) 12 (162) 28 (4 3 (7.9) 1 (885) Case Flow 25 (6.6) 8 (78) 2 (5.3) 6 (531) 15 (22 15 (22, Case Flow 15 (4.) 4 (354) Torque 1 (2.6) 2 (177) 5 (1.3) 5 1 15 2 25 16 (4.2) Speed r/min Case Flow at 22 r/min, Full Flow 93 C (2 F), 1. absolute ( psi gauge) Inlet 14 (3.7) 12 (3.2) 1 (2.6) 8 (2.1) 6 (1.6) 4 (1.) 2 (.5) 5 1 15 2 25 (7) (15) (22) (29) (36) 3 (44) 35 (5) Case Flow at 22 r/min, Minimum Flow 935C (25F), 1. absolute ( psi gauge) Inlet 32 (8.4) 28 (7.4) 24 (6.3) 2 (5.3) 16 (4.2) 12 (3.2) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Case Flow l/min (USgpm) 62 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Performance Quiet version, optimized for 1-18 rpm (E) PVM16 Noise Level dba dba Typical Noise Levels at 18 and 12 r/min. Typical Noise Levels at 18 and 12 r/min. with Petroleum Oil (1W) at 5 C (12 F) with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet and 1. absolute ( psi gauge) Inlet 8 8 78 78 76 76 74 74 18 r/min max. 18 flow r/min max. flow 72 18 r/min 72 min. 18 flow r/min 12 r/min min. flow min. 12 flow r/min 7 min. flow 7 68 68 12 r/min 66 12 r/min 66 max. flow max. flow 64 64 62 62 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) Outlet Pressure ( Efficiency Efficiency - % Delivery and Efficiency at at 18 r/min, 5C (12F), and 1. 1. absolute ( ( psi gauge) Inlet 1 1 Volumetric Efficiency 9 9 8 8 7 7 6 6 5 5 4 4 3 3 Delivery Delivery l/min l/min (USgpm) (USgpm) 25 25 (66) (66) 2 2 (53) (53) 15 15 (4) (4) 2 2 1 1 (26) (26) 1 1 5 5 (13) (13) 5 5 1 1 15 15 2 2 25 25 (7) (15) (22) (29) (36) Outlet Pressure - - ( De D 11 9 8 7 6 Efficiency 5 4 3 2 1 Noise Level dba dba 76 76 74 74 72 72 7 7 68 68 66 66 64 64 62 62 6 6 Typical Noise Levels at 15 and 1 r/min. Typical Noise Levels at 15 and 1 r/min. with Petroleum Oil (1W) at 5 C (12 F) with Petroleum Oil (1W) at 5 C (12 F) and 1. absolute ( psi gauge) Inlet and 1. absolute ( psi gauge) Inlet 15 r/min min. 15 flow r/min min. flow 15 r/min max. 15 flow r/min 1 r/min max. flow min. 1 flow r/min min. flow 1 r/min max. 1 flow r/min max. flow 58 58 5 1 15 (7) 5 (15) 1 (22) 15 (7) Outlet (15) Pressure (22) ( Sound pressure data Outlet Pressure ( Sound pressure data equivalent to NFPA. equivalent to NFPA. 2 (29) 2 (29) 25 (36) 25 (36) Torque Torque Nm Nm (in.lb.) (in.lb.) Torque and Power at at 18 r/min, 5C (12F), and 1. 1. absolute ( ( psi gauge) Inlet 5 5 (4425) 45 45 (3982) 4 4 (354) 35 35 (397) 3 3 (2655) 25 25 (2212) 2 2 (177) 15 15 (1327) 1 1 (885) 5 5 (442) Torque, Full Power, Full Torque, Cut-off 5 5 1 1 15 15 2 2 (7) (15) (22) (29) Outlet Pressure - - ( 25 25 (36) Power Power kw kw (hp) (hp) 1 1 (134) 75 75 (11) 5 5 (67) (67) 25 25 (34) (34) Torque Torque Nm Nm (in.lb.) (in.lb.) InI EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 63
Performance Quiet version, optimized for 1-18 rpm (E) PVM16 66) (66) 53) (53) 4) (4) 26) (26) 3) 3) Delivery Delivery and and Efficiency Efficiency at at 15 15 r/min, r/min, 5C 5C (12F), (12F), and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 1 1 Volumetric Volumetric Efficiency Efficiency 9 9 Overall Efficiency 8 8 Efficiency % 7 7 6 6 5 5 4 4 3 3 Delivery l/min l/min (USgpm) 25 25 (66) (66) 2 2 (53) (53) Delivery Delivery (effective (effective flow) flow) 15 15 (4) (4) 2 2 1 1 (26) (26) 1 1 5 5 (13) (13) 5 5 1 1 15 15 2 2 25 25 (7) (7) (15) (15) (22) (22) (29) (29) (36) (36) Outlet Outlet Pressure Pressure ( ( Delivery and Efficiency at 12 r/min, 5C (12F), Delivery and 1. and Efficiency absolute at ( 12 psi r/min, gauge) 5C Inlet (12F), and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency 9 Volumetric Efficiency 9 8 8 7 7 6 6 5 25 (66) 5 4 25 (66) 2 (53) 4 3 2 (53) 15 (4) 3 2 15 (4) 1 (26) 2 1 1 (26) 5 (13) 1 5 (13) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) Efficiency Efficiency % % Delivery Delivery l/min l/min (USgpm) (USgpm) Efficiency Efficiency % % Deliver Delive an a 1 1 Volu 9 Vo 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 F), ), Power Power kw kw (hp) (hp) (134) (134) 11) 1) 67) 7) 34) 4) Torque Torque Nm Nm (in.lb.) (in.lb.) Torque Torque and and Power Power at at 15 15 r/min, r/min, 5C 5C (12F), (12F), and and 1. 1. absolute absolute ( ( psi psi gauge) gauge) Inlet Inlet 5 5 (4425) (4425) 45 45 (3982) (3982) 4 4 (354) (354) Torque, Torque, 35 35 (397) (397) Full Full Stroke Stroke 3 3 (2655) (2655) 25 25 (2212) (2212) 2 2 (177) (177) 15 15 (1327) (1327) Power, Power, Full Full Stroke Stroke 1 1 (885) (885) 5 5 (442) (442) 5 5 1 1 15 15 2 2 (7) (7) (15) (15) (22) (22) (29) (29) Outlet Outlet Pressure Pressure ( ( 25 25 (36) (36) Power Power kw kw (hp) (hp) 1 1 (134) (134) 75 75 (11) (11) 5 5 (67) (67) 25 25 (34) (34) Torque Torque Nm Nm (in.lb.) (in.lb.) Torque and Power at 12 r/min, 5C (12F), and Torque 1. and absolute Power at (12 psi gauge) r/min, 5C Inlet(12F), 5 (4425) and 1. absolute ( psi gauge) Inlet 5 (4425) 45 (3982) 45 (3982) 4 (354) 4 (354) Torque, 35 (397) Full Stroke Torque, 35 (397) 3 (2655) 3 (2655) 25 (2212) 25 (2212) 2 (177) 1 (134) 2 (177) 1 (134) 15 (1327) 75 (11) 15 (1327) Power, 1 (885) 75 (11) Power, 5 (67) 1 (885) 5 (67) 5 (442) 25 (34) 5 (442) 25 (34) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) Power Power kw kw (hp) (hp) Torque Torque Nm Nm (in.lb.) (in.lb.) In I 5 5 45 45 4 4 35 35 3 3 25 25 2 2 15 15 1 1 5 64 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Performance Quiet version, optimized for 1-18 rpm (E) PVM16 F),, (66) (66) (53) (53) (4) (4) (26) (26) (13) 3) Delivery and Efficiency at 1 r/min, 5C (12F), Delivery and and 1. Efficiency absolute at 1 ( psi r/min, gauge) 5C Inlet (12F), and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency 9Volumetric Efficiency 9 8 8 7 7 6 6 5 25 (66) 5 25 (66) 4 2 (53) 4 2 (53) 3 15 (4) 3 15 (4) 2 1 (26) 2 1 (26) 1 5 (13) 1 5 (13) 5 1 15 2 25 5 (7) 1 (15) 15 (22) 2 (29) 25 (36) (7) Outlet (15) Pressure (22) ( (29) (36) Case Case Flow Flow l/min l/min (USgpm) (USgpm) Case Flow versus Outlet Pressure at 18 r/min, Full Flow, Case 5 C Flow (12 F), versus and Outlet 1. Pressure absolute at 18 ( psi r/min, gauge) Full Inlet Flow, 4. (1.6) 5 C (12 F), and 1. absolute ( psi gauge) Inlet 4. (1.6) 3.5 (.92) 3.5 (.92) 3. (.79) 3. (.79) 2.5 (.66) 2.5 (.66) 2. (.53) 2. (.53) 1.5 (.4) 1.5 (.4) 1. (.26) 1. (.26).5 (.13).5 (.13) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) (12F), et 2F), Power kw (hp) Power kw (hp) 1 (134) (134) 75 (11) (11) 5 (67) (67) 25 (34) (34) ) Torque Nm (in.lb.) Torque Nm (in.lb.) Torque and Power at 1 r/min, 5C (12F), Torque and 1. and Power absolute at 1 ( psi r/min, gauge) 5C Inlet (12F), 5 (4425) and 1. absolute ( psi gauge) Inlet 5 (4425) 45 (3982) 45 (3982) 4 (354) 4 (354) Torque, 35 (397) Full Torque, Stroke 35 (397) 3 (2655) 3 (2655) 25 (2212) 25 (2212) 2 (177) 1 (134) 2 (177) 1 (134) 15 (1327) 75 (11) 15 (1327) Power, 75 (11) 1 (885) Full Power, Stroke 5 (67) 1 (885) 5 (67) 5 (442) 25 (34) 5 (442) 25 (34) 5 1 15 2 25 5 (7) 1 (15) 15 (22) 2 (29) 25 (36) (7) Outlet (15) Pressure (22) ( (29) (36) Power kw (hp) Power kw (hp) Case Case Flow Flow l/min l/min (USgpm) (USgpm) Case Flow versus Outlet Pressure at Cutoff, 18 r/min, Case 5 C Flow (12 F), versus and Outlet 1. Pressure absolute at ( Cutoff, psi gauge) 18 r/min, Inlet 5 C (12 F), and 1. absolute ( psi gauge) Inlet 21 (5.55) 21 2 (5.55) (5.28) 2 19 (5.28) (5.2) 19 18 (5.2) (4.76) 18 17 (4.76) (4.49) 17 16 (4.49) (4.23) 16 15 (4.23) (3.96) 15 14 (3.96) (3.7) 14 13 (3.7) (3.43) 13 12 (3.43) (3.17) 12 11 (3.17) (2.91) 11 (2.91) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 65
(%) (%) (%) Noise Level dba Noise Level dba Noise Level dba Performance Higher speed version (M) PVM16 Typical Noise Typical Levels Noise at 22 Levels & at 622 r/min & 6 r/min with Petroleum with Petroleum Oil (1W) at Oil 93 C (1W) (2 F) at 93 C (2 F) and 1. and absolute 1. ( absolute psi gauge) ( psi Inlet gauge) Inlet 86 86 82 78 74 7 66 62 58 82 22 r/min max. flow 78 74 7 6 r/min min. flow 66 62 58 6 r/min min. flow 22 r/min max. flow 22 r/min min. flow 6 r/min max. flow 22 r/min min. flow 54 54 5 1 5 15 1 2 15 25 2 (7) (15) (7) (22) (15) (29) (22) (36) (29) Outlet Pressure Outlet Pressure ( ( Sound pressure Sound datapressure data equivalent to equivalent NFPA. to NFPA. 86 82 6 r/min max. flow 78 74 62 Typical Noise Levels at 22 & 6 r/min with Petroleum Oil (1W) at 93 C (2 F) and 1. absolute ( psi gauge) Inlet 7 25 (36) 6 r/min min. flow 66 22 r/min max. flow 22 r/min min. flow 6 r/min max. flow 58 54 5 (7) Sound pressure data equivalent to NFPA. 1 15 (15) (22) 2 (29) 25 (36) versus Speed versus at Speed at Delivery and Delivery Case Flow and Case versus Flow Speed versus at 93 C Speed (2 F), at 93 C (2 F), 93 C (2 F) 93 C and (2 F) 1. and absolute 1. ( absolute psi gauge) ( psi inlet gauge) inlet Full Flow 1. Full Flow absolute 1. ( absolute psi gauge) ( psi Inlet gauge) Inlet 24 (63) 24 (63) 1 1 22 (58) 22 (58) 95 1 1 5 (725 15 (145 2 (53) 5 (725 95 15 (145 2 (53) Delivery Delivery (22 (22 9 18 (48) 9 18 (48) 85 16 (42) 16 (42) 85 2 21 (3 Case Flow 2 versus Speed at 21 (3 Case Flow Delivery and Case (29 (29 8 5 (72593 C (2 F) and 14 1. (37) 14 (37) Delivery l/min 8 absolute ( psi gauge) inlet Delivery l/min Full Flow 1. b 23 (33 5 (725 (USgpm) (USgpm) 12 (32) 75 23 (33 12 (32) 75 24 (63) 21 7 1 1 (26) 1 (2.6) 21 1 (26) 1 (2.6) 22 (58) 7 (3 (3 1 65 95 8 (21) 15 (145 2 (53) 8 (2.11) 65 8 (21) 8 (2.11) 6 6 9 (22 6 (16) 6 (16) 21 (321 Case (3 Flow Case Flow 6 (1.59) 18 (48) 6 (1.59) 4 (11) 16 (42) 4 (1.6) 55 55 85 4 (11) 4 (1.6) 2 5 (725 Case Flow (29 2 (5) 5 (725 Case Flow 14 (37) 2 (.53) 5 5 8 2 (5) 2 (.53) 5 (725 5 1 15 2 25 3 23 (33 5 1 15 2 25 3 12 (32) 75 5 15 15 1 2 15 25 2 25 Speed r/min 21 1 (26) Speed r/min 7 Speed (r/min) Speed (r/min) (3 65 8 (21) 6 6 (16) 55 4 (11) 5 2 (5) 5 1 15 2 25 3 5 66 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 Speed r/min
Performance Higher speed version (M) PVM16 Torque Torque Torque Nm (in.lb.) Nm (in.lb.) Nm (in.lb.) Torque Nm (in.lb.) Torque versus Speed Speed at at 93 C 93 C (2 F), Full Full Flow Flow and and 1. 1. absolute ( psi ( psi gauge) Inlet Inlet 45 45 (3982) (3982) Torque versus Speed at at 93 C (2 F), Full Full Flow and 1. 1. absolute ( ( psi psi gauge) Inlet 4 4 (354) (354) 23 23 (33 (33 45 45 (3982) 21 21 (3 (3 35 4 35 (397) (397) 23 2 23 2 (33 (29 (29 4 (354) 3 3 (2655) (2655) 21 21 (3 35 35 (397) 2 15 2 15 (29 (22 (22 25 3 3 25 (2212) (2655) (2212) 15 15 (22 25 2 25 (2212) 2 (177) (177) 1 1 (15 (15 2 15 2 15 (177) (1327) (1327) 1 15 15 1 (885) (1327) (885) 1 5 1 (885) (442) 5 (885) (442) 1 1 (15 5 5 (725 (725 175 17 (725 (25 (725 (25 5 5 (442) (442) 5 51 115 152 225 17 25 17 3 (25 (25 3 Speed Speed (r/min) (r/min) 5 5 1 15 2 25 3 Speed (r/min) Power versus Speed at at 93 C (2 F), 1 1 (134) Full (134) Full Flow and 1. 1. absolute ( ( psi psi 23 gauge) 23 (33 (33 Inlet 9 (121) 9 (121) 21 21 (3 (3 1 1 (134) (134) 8 (17) 8 (17) 23 15 23 15 (33 (22 (22 9 9 (121) (121) 21 21 (3 7 (94) 7 (94) 8 (17) 15 8 (17) 15 (22 6 (8) 6 (8) 1 1 (15 (15 7 7 (94) (94) 5 (67) 5 (67) 6 (8) 1 6 (8) 1 (15 4 (54) 4 (54) 5 5 (67) (67) 3 (4) 3 (4) 4 4 (54) (54) 5 5 (725 (725 2 (27) 2 (27) 3 3 (4) (4) 1 (13) 1 (13) 175 17 (725 (25 (725 (25 2 2 (27) (27) 1 1 (13) (13) 5 51 115 152 225 1725 3 (25 (25 3 Power Power Power kw (hp) kw (hp) kw (hp) Power kw (hp) Power Power versus Speed Speed at at 93 C 93 C (2 F), Full Full Flow Flow and and 1. 1. absolute ( psi ( psi gauge) Inlet Inlet Speed Speed (r/min) (r/min) 5 5 1 15 2 25 3 Speed (r/min) Torque and and Case Case Flow Flow versus Speed Speed at at 93 C 93 C (2 F), Load Load Sense Sense Standby and and 1. 1. absolute ( psi ( psi gauge) Inlet Inlet Torque and Case Flow versus Speed at at 93 C (2 F), 12 (16) 12 (16) Load Sense Standby and 1. 1. absolute ( ( psi psi gauge) Inlet 11 (97) 11 (97) 12 12 (16) (16) 2 2 (3 (3 1 (88) 1 (88) diff. diff. Torque Torque 11 11 (97) (97) 9 (8) 9 (8) 2 (3 1 (88) 2 (3 1 (88) 8 (71) 8 (71) diff. diff. Torque Case Case 9 (8) 9 (8) Flow Flow l/min l/min 7 (62) 7 (62) 11 11 (16 (16 diff. diff. (USgpm) (USgpm) 8 (71) 8 (71) Torque Torque Case Case 6 (53) 6 (53) Flow Flow l/min l/min 7 (62) 7 (62) 11 11 (16 (16 diff. diff. 9. 9. (2.38) (2.38) (USgpm) 5 (44) 5 (44) Torque 8.5 8.5 (2.25) (2.25) 6 (53) 6 (53) 4 (35) 4 (35) 9. 9. (2.38) 8. 8. (2.11) (2.11) 5 (44) 5 (44) 3 (27) 3 (27) 2 2 (3 (3 8.5 8.5 (2.25) 7.5 7.5 (1.98) (1.98) 4 (35) 4 (35) diff. diff. Case Case Flow Flow 11 11 (16 (16 diff. diff. 2 (18) 2 (18) Case Case Flow Flow 8. 8. (2.11) 7. 7. (1.85) (1.85) 3 (27) 3 (27) 2 2 (3 (3 7.5 1 (9) 1 (9) diff. Flow 7.5 (1.98) diff. Case Flow 11 11 (16 (16 diff. diff. 6.5 6.5 (1.72) (1.72) 2 (18) 2 (18) Case Flow Flow 7. 7. (1.85) 6. 6. (1.59) (1.59) 1 (9) 1 (9) 5 5 1 1 15 15 2 2 25 25 6.5 6.5 (1.72) Speed Speed (r/min) (r/min) 6. 6. (1.59) 5 5 1 15 2 25 Speed (r/min) Torque Torque Torque Nm (in.lb.) Nm (in.lb.) Nm (in.lb.) Torque Nm (in.lb.) ( Torque ( Torque ( Torque Nm (in.lb.) Nm (in.lb.) Nm (in.lb.) ( Torque Nm (in.lb.) Torque and and Case Case Flow Flow versus Speed Speed at at 93 C 93 C (2 F), Pressure Limit Limit Cut-off and and 1. 1. absolute ( psi ( psi gauge) Inlet Inlet Torque and Case Flow versus Speed at at 93 C (2 F), 14 14 (1239) (1239) Pressure Limit Cut-off and 1. 1. absolute ( psi 13 13 (115) (115) ( psi gauge) Inlet 14 14 (1239) 21 21 (3 (3 Torque Torque 12 12 (162) (162) 13 11 13 (115) 11 (973) (973) 21 12 21 (3 Torque 12 1 (162) 1 (885) (885) 11 9 11 (973) (796) 9 (973) (796) Case Case 1 (885) Flow Flow l/min l/min 1 8 (885) (78) 8 (78) 15 15 (22 (22 (USgpm) (USgpm) 9 (796) Case Case 9 (796) Torque Torque 7 (619) 7 (619) Flow Flow l/min l/min 68 (78) (531) 6 (78) (531) 15 15 (22 3 Torque (USgpm) (7.9) 3 (7.9) 57 (619) (442) 5 (619) (442) 25 (6.6) 25 (6.6) 21 21 (3 (3 Case Case Flow Flow 6 6 (531) (531) 3 3 (7.9) (7.9) 4 (354) 4 (354) 2 (5.3) 2 (5.3) 35 (442) (265) 3 (442) (265) 25 25 (6.6) (6.6) 21 21 (3 (3 Case Case Flow Flow 15 (4.) 15 (4.) 24 (354) (177) (354) 15 15 (22 (22 2 (177) 2 2 (5.3) (5.3) Case Case Flow Flow 1 (2.6) 1 (2.6) 31 (265) (88) (265) 1 (88) 15 (4.) 15 2 2 (177) (177) 15 (22 15 5 (1.3) (4.) 5 (1.3) Flow 1 (2.6) Case Flow 1 (2.6) 1 1 (88) (88) 5 5 1 1 15 15 2 2 25 25 5 5 (1.3) (1.3) Speed Speed (r/min) (r/min) 5 5 1 15 2 25 Speed (r/min) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 67
Performance Quiet version, optimized for 1-18 rpm (E) PVM131 Noise Noise Level Level dba dba Noise Noise Level Level dba dba Typical Noise Levels at 18 and 12 r/min with Petroleum Oil (1W) at 5 C (12 F) Delivery and Efficiency at 18 r/min Typical Noise and 1. Levels absolute at 18 ( psi gauge) and 12 Inlet r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 82 with Petroleum Oil (1W) at 5 C (12 F) 1 and 1. absolute ( psi gauge) Inlet Delivery and Efficiency at 18 r/min 82 8 18 r/min Volumetric 9 5 C (12 F) and 1. absolute ( psi gauge) Inlet Max. Flow Efficiency 1 8 78 18 r/min 8 Max. Flow Volumetric 78 76 18 r/min 9 Efficiency Min. Flow 7 76 74 18 r/min 8 Min. Flow 6 24 (63) 74 72 7 12 r/min 5 2 (53) 72 7 Max. Flow 6 24 (63) 12 r/min 12 r/min 4 16 (42) 7 68 Max. Flow Min. Flow 5 2 (53) 3 12 (32) 66 12 r/min 68 Min. Flow 4 16 (42) 664 2 8 (21) 3 12 (32) 64 62 1 4 (11) 2 8 (21) 62 6 5 1 15 2 25 3 1 5 1 15 2 25 3 35 4 (11) 6 (7) (15) (22) (29) (36) (44) (7) (15) (22) (29) (36) (44) (5) 5 Outlet 1 Pressure 15 2 ( 25 3 Sound (7) pressure data (15) (22) (29) (36) (44) 5 1 15 2 25 3 35 equivalent to NFPA (7) (15) (22) (29) (36) (44) (5) Sound pressure data equivalent Typical to Noise NFPA Levels at 15 and 1 r/min Torque and Power at 18 r/min with Petroleum Oil (1W) at 5 C (12 F) 5 C (12 F) and 1. absolute ( psi gauge) Inlet Typical Noise and 1. Levels absolute at 15 ( psi gauge) and 1 Inlet r/min 72 (6372) 76 with Petroleum Oil (1W) at 5 C (12 F) Torque and Power at 18 r/min and 1. absolute ( psi gauge) Inlet 66 (5841) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 76 15 r/min 74 6 (531) 72 (6372) Max. Flow 15 r/min Torque 54 (4779) 66 (5841) 74 72 Max. Flow 48 (4248) 6 (531) 72 7 Torque 42 (3717) 54 (4779) 14 (188) 7 68 36 (3186) 48 (4248) 12 (161) 68 66 1 r/min 3 (2655) 42 (3717) Power, 1 (134) 14 (188) Max. Flow 1 r/min 664 1 r/min 24 (2124) 36 (3186) 8 (17) 12 (161) Max. Flow Min. Flow 1 r/min 18 (1593) 3 (2655) Power, 1 (134) 64 62 Min. Flow 6 (81) 24 (2124) Torque, 12 (162) Cut-off 4 (54) 8 (17) 15 r/min 62 6 Min. Flow 6 (531) 18 (1593) 2 (27) 6 (81) 15 r/min Torque, 6 58 Min. Flow 12 (162) Cut-off 4 (54) 5 1 15 2 25 3 35 58 56 6 (531) (7) (15) (22) (29) (36) (44) (5) 2 (27) 5 1 15 2 25 3 56 (7) (15) (22) (29) (36) (44) 5 1 15 2 25 3 35 5 Outlet 1 Pressure 15 2 ( 25 3 (7) (15) (22) (29) (36) (44) (5) (7) (15) (22) (29) (36) (44) Torque Nm (in.lb.) Torque Nm (in.lb.) Power kw (hp) Power kw (hp) 68 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Performance Quiet version, optimized for 1-18 rpm (E) PVM131 1 9 8 7 6 5 4 3 2 1 Delivery and Efficiency at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet Delivery and Efficiency at 15 r/min Volumetric 5 C (12 F) and 1. absolute ( psi gauge) Inlet Efficiency 1 Volumetric 9 Efficiency 8 7 6 5 4 3 2 1 5 1 15 2 25 3 (7) (15) (22) (29) (36) (44) 5 Outlet 1 Pressure 15 ( 2 25 (7) (15) (22) (29) (36) 3 (44) 24 (63) 2 (53) 24 (63) 16 (42) 2 (53) 12 (32) 16 (42) 8 (21) 12 (32) 4 (11) 8 (21) 35 4 (11) (5) 35 (5) 1 9 8 7 6 5 4 3 2 1 Delivery and Delivery Efficiency and Efficiency at 12 r/min at 12 r/min 5 C (12 F) 5 C and (12 F) 1. and absolute 1. ( absolute psi gauge) ( psi Inlet gauge) Inlet 1 Volumetric Volumetric Efficiency 9 Efficiency 8 7 6 5 4 3 2 1 24 (63) 2 (53) Delivery (effective Delivery flow) (effective flow) 16 (42) 12 (32) 8 (21) 4 (11) 5 1 5 151 2 15 25 2 3 25 35 3 (7) (15) (7)(22) (15)(29) (22)(36) (29)(44) (36)(5) (44) Outlet Pressure Outlet Pressure ( ( 24 (63) 2 (53) 16 (42) 12 (32) 8 (21) 4 (11) 35 (5) Torque Nm (in.lb.) Torque and Power at 15 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 72 (6372) Torque and Power at 15 r/min 66 (5841) 72 (6372) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 6 (531) 66 (5841) Torque 54 (4779) 6 (531) 48 (4248) 54 (4779) Torque 42 (3717) 48 (4248) 36 (3186) 42 (3717) 12 (161) 3 (2655) 36 (3186) 1 (134) 12 (161) 24 (2124) 8 (17) 3 (2655) 1 (134) Power, 18 (1593) 24 (2124) 6 (81) 8 (17) 12 (162) 18 (1593) Power, 4 (54) 6 (81) 6 (531) 12 (162) 2 (27) 4 (54) 6 (531) 5 1 15 2 25 3 35 2 (27) (7) (15) (22) (29) (36) (44) (5) 5Outlet 1 Pressure 15 ( 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque Nm (in.lb.) Torque Nm (in.lb.) Torque and Torque Power and at Power 12 r/min at 12 r/min 66 (5841) 5 C (12 F) 5 C and (12 F) 1. and absolute 1. ( absolute psi gauge) ( psi Inlet gauge) Inlet 66 (5841) 6 (531) 6 (531) Torque Torque 54 (4779) 54 (4779) 48 (4248) 48 (4248) 42 (3717) 42 (3717) 36 (3186) 36 (3186) 3 (2655) 3 (2655) Power, Power, 1 (134) 1 (134) 24 (2124) 24 (2124) 8 (17) 8 (17) 18 (1593) 12 (162) 6 (531) 18 (1593) 12 (162) 6 (531) 6 (81) 4 (54) 2 (27) 6 (81) 4 (54) 2 (27) 5 15 151 2 15 25 2 3 25 35 3 35 (7) (15) (7) (22) (15)(29) (22)(36) (29) (44) (36) (5) (44) (5) Outlet Pressure Outlet Pressure ( ( Power kw (hp) Power kw (hp) Torque Nm (in.lb.) Power kw (hp) Power kw (hp) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 69
Performance Quiet version, optimized for 1-18 rpm (E) PVM131 Delivery and Efficiency at 1 r/min Delivery and Efficiency at 1 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 5 C (12 F) and 1. absolute ( psi gauge) Inlet 1 1 Volumetric 9 Efficiency Volumetric 9 Efficiency 8 8 7 7 6 6 5 5 2 (53) 2 (53) 4 4 16 (42) 16 (42) 3 3 12 (32) 12 (32) 2 2 8 (21) 8 (21) 1 1 4 (11) 4 (11) 5 1 15 2 25 3 35 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (44) 3 (5) 35 (7) Outlet (15) Pressure (22) (29) ( (36) (44) (5) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Case Flow Versus Outlet Pressure at Full Flow, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 8 (2.1) Case Flow Versus Outlet Pressure at Full Flow, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 8 (2.1) 7 (1.8) 7 (1.8) 6 (1.6) 6 (1.6) 5 (1.3) 5 (1.3) 4 (1.1) 4 (1.1) 3 (.8) 3 (.8) 2 (.5) 2 (.5) 1 (.3) 1 (.3) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 Outlet 1 Pressure 15 2 ( 25 3 35 (7) (15) (22) (29) (36) (44) (5) Torque Nm (in.lb.) Torque and Power at 1 r/min Torque and Power at 1 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 66 (5841) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 66 (5841) 6 (531) 6 (531) Torque 54 (4779) Torque 54 (4779) 48 (4248) 48 (4248) 42 (3717) 42 (3717) 36 (3186) 36 (3186) 3 (2655) 1 (134) 3 (2655) 1 (134) 24 (2124) Power, 8 (17) 24 (2124) Power, 8 (17) 18 (1593) 6 (81) 18 (1593) 6 (81) 12 (162) 4 (54) 12 (162) 4 (54) 6 (531) 2 (27) 6 (531) 2 (27) 5 1 15 2 25 3 35 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (44) 3 (5) 35 (7) (15) (22) (29) (36) (44) (5) Torque Nm (in.lb.) Power kw (hp) Power kw (hp) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 24 (6.3) 5 C (12 F) and 1. absolute ( psi gauge) Inlet 24 (6.3) 2 (5.3) 16 (4.2) 12 (3.2) 8 (2.1) 4 (1.1) 2 (5.3) 16 (4.2) 12 (3.2) 8 (2.1) 4 (1.1) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) 5 Outlet 1 Pressure 15 2 ( 25 3 35 (7) (15) (22) (29) (36) (44) (5) 7 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
(%) (%) Case Flow l/min (USgpm) Case Flow l/min (USgpm) Performance Higher speed version (M) PVM131 Noise Level dba Noise Level dba Typical Noise Levels at 2 and 6 r/min Typical with Noise petroleum Levels oil (1 at W) 2 @ 93 C and (2 F) 6 r/min and with 1. petroleum absolute oil (1 ( W) psi @ gauge) 93 C inlet (2 F) 84 and 1. absolute ( psi gauge) inlet 2 r/min 8284 Max. 2 flow r/min 882 Max. flow 788 7678 2 r/min Min. flow 6 r/min 7476 2 r/min Min. flow Min. 6 flow r/min 7274 Min. flow 772 687 6668 6 r/min 6466 Max. 6 flow r/min 6264 Max. flow 662 586 5 1 15 2 25 3 58 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (44) 3 (7) Outlet (15) Pressure (22) ( (29) (36) (44) Sound pressure data equivalent Sound pressure to NFPAdata equivalent to NFPA Versus Speed Overall @ 93 C (2 F) Efficiency and 1. Versus absolute Speed @ 93 C ( (2 F) psi gauge) and 1. inlet absolute 95 ( psi gauge) inlet 95 Torque Nm (in.lb.) 9 9 1 (15 1 85 (15 5 (7 85 (22 15 5 (7 (22 8 2 8(29 2 75 25 (29 (36 75 25 28 (36 7 (4 28 7 (4 32 (46 65 32 (46 5 1 15 2 25 65 5 1 Speed r/min 15 2 25 Speed r/min Delivery and Case Flow Versus Speed @ 93 C (2 F), full flow and 1. absolute ( gauge Inlet 26 (69) Delivery and Case Flow Versus Speed 24 (63) @ 5 93 C (7 (2 F),, full flow and 1. Delivery absolute ( gauge Inlet 22 (58) 26 (69) 2 (53) 24 (63) 5 (7, 18 (48) Delivery 28 (4, 22 (58) Delivery 16 (42) 2 (53) 14 (37) 18 (48) 28 (4, Delivery 12 (32) 16 (42) 1 (26) 2 (5.3) 14 (37) 28 (4, 8 (21) 16 (4.2) 12 (32) Case flow 6 (16) 12 (3.2) 1 (26) 2 (5.3) 4 (11) 28 (4, 6 (2.1) 8 (21) 16 (4.2) Case flow 2 (5) 5 (7, Case flow 4 (1.1) 6 (16) 12 (3.2) 4 (11) 5 1 15 2 25 6 (2.1) 2 (5) 5 Speed (7 r/min, Case flow 4 (1.1) 5 Torque 1 Versus Speed 15 2 25 @ 93 C (2 F), Speed full flow r/minand 1. absolute ( psi gauge) inlet 8 (78) Torque Versus Speed @ 93 C (2 F), full flow and 7 (6195) 1. absolute ( psi gauge) inlet 8 (78) 32 (46 6 (531) 7 (6195) 28 (4 5 (4425) 25 32 (36 (46 6 (531) 4 (354) 2 28 (29 (4 5 (4425) 25 (36 3 (2655) 15 (22 4 (354) 2 (29 2 (177) 1 (15 3 (2655) 15 (22 1 (885) 5 (7 2 (177) 1 (15 17 (25 1 (885) 5 1 15 2 525 (7 Speed r/min 17 (25 5 1 15 2 25 Speed r/min Torque Nm (in.lb.) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 71
Power Power kw kw (hp) (hp) Case Case Flow Flow (l/min (l/min (USgpm) (USgpm) Performance Higher speed version (M) PVM131 Torque Torque Nm Nm (in.lb.) (in.lb.) Power Versus Speed @93 C Power (2 F), Versus full flow Speed and 1. @93 C absolute (2 F), ( full psi flow gauge) and inlet 14 (188) 1. absolute ( psi gauge) inlet 32 (46 13 14 (174) (188) 32 (46 12 13 (161) (174) 28 (4 12 11 (161) 28 (4 (148) 25 (36 1 11 (134) (148) 25 (36 1 9 (134) (121) 2 (29 8 9 (17) (121) 2 (29 8 7 (17) (94) 15 (22 6 7 (8) (94) 15 (22 5 6 (67) (8) 1 (15 4 5 (54) (67) 1 (15 3 4 (4) (54) 5 (7 2 3 (27) (4) 5 (7 1 2 (13) (27) 17 (25 1 (13) 17 (25 5 1 15 2 25 5 1 Speed r/min 15 2 25 Speed r/min Torque and Case Flow Versus Speed Torque @ 93 C and (2 F), Case load Flow sense Versus standby Speed and @ 93 C 1. (2 F), absolute load ( sense psi gauge) standby inlet 18 (159) and 1. absolute ( psi gauge) inlet 18 (159) 2 (3 16 (142) differential, 2 (3 16 (142) differential, Torque 14 (124) Torque 14 (124) 12 (16) 11 (16 12 (16) differential, 11 (16 1 (88) differential, Torque 1 (88) Torque 8 (71) 7 (1.85) 8 (71) 7 (1.85) 6 (53) 2 (3 differential 6 (1.58) 6 (53) Case 2 Flow (3 differential 6 (1.58) 4 (35) Case Flow 5 (1.32) 4 (35) 5 (1.32) 2 (18) 11 (16 differential 4 (1.6) 2 (18) Case 11 Flow (16 differential 4 (1.6) Case Flow 3 (.79) 5 1 15 2 253 (.79) 5 1 Speed r/min 15 2 25 Speed r/min Torque Nm (in.lb.) Case Flow l/min (USgpm) Case Flow l/min (USgpm) 26 (231) 24 (2124) 22 (1947) 2 (177) 18 (1593) 16 (1416) 14 (1239) 12 (162) 1 (885) 8 (78) 6 (531) 4 (354) 2 (177) 18 (4.7) Torque and Case Flow Versus Speed @ 93 C (2 F), cut-off and 1. absolute ( psi gauge) inlet 15 (22 Torque 28 (4 Torque 28 (4, Case Flow 15 (22, Case Flow 5 1 15 2 25 Speed r/min Case Flow at 2 r/min, Full Flow 93 C (2 F), 1. absolute ( psi gauge) Inlet 16 (4.2) 14 (3.7) 12 (3.2) 1 (2.6) 8 (2.1) 6 (1.6) 4 (1.) 2 (.5) 5 1 15 2 25 (7) (15) (22) (29) (36) 3 (44) 35 (5) 56 (14.8) 48 (12.7) 4 (1.6) 32 (8.5) 24 (6.3) 16 (4.2) 8 (2.1) Case Flow at 2 r/min, Minimum Flow 93 C (2 F), 1. absolute ( psi gauge) Inlet 28 (7.4) 24 (6.3) 2 (5.3) 16 (4.2) 12 (3.2) 8 (2.1) 4 (1.) 5 1 15 2 25 3 35 (7) (15) (22) (29) (36) (44) (5) Case Flow l/min (USgpm) 72 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Performance Quiet version, optimized for 1-18 rpm (E) PVM141 Noise Noise Level Level dba dba Typical Noise Levels at 18 and 12 r/min Typical with Petroleum Noise Levels Oil at (1W) 18 at and 5 C 12 (12 F) r/min with and Petroleum 1. absolute Oil (1W) ( psi at gauge) 5 C (12 F) Inlet 84 and 1. absolute ( psi gauge) Inlet 84 82 18 r/min 82 max. 18 flow r/min 8 max. flow 8 78 78 76 76 74 12 r/min 74 max. 12 flow r/min 72 max. flow 72 18 r/min 7 min. 18 flow r/min 7 min. flow 68 68 66 66 64 12 r/min 64 min. 12 flow r/min 62 min. flow 62 6 6 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) Delivery and Efficiency at 18 r/min, 5C (12F), and 1. absolute ( psi gauge) Inlet Delivery 1 and Efficiency at 18 r/min, 5C (12F), and 1. absolute ( psi gauge) Inlet Volumetric Efficiency 1 9 Volumetric Efficiency 9 8 8 7 Efficiency % 7 6 6 5 5 4 4 3 3 2 2 1 1 5 1 15 2 (7) (15) (22) (29) 5 1 15 2 (7) Outlet (15) Pressure (22) ((29) 3 (79) 3 25 (79) (66) 25 2 (66) (53) 2 15 (53) (4) 15 1 (4) (26) 1 5 (13) (26) 5 (13) 25 (36) 25 (36) Delivery Delivery l/min l/min (USgpm) (USgpm) De De 1 Efficiency % Noise Noise Level Level dba dba Typical Noise Levels 15 and 1 r/min Typical with Petroleum Noise Levels Oil (1W) 15 and at 5 C 1 (12 F) r/min with and Petroleum 1. absolute Oil (1W) ( psi at gauge) 5 C (12 F) Inlet 78 and 1. absolute ( psi gauge) Inlet 78 76 76 15 r/min 74 max. 15 flow r/min 74 max. flow 72 1 r/min 72 7 max. 1 flow r/min 7 max. flow 68 68 15 r/min 66 min. 15 flow r/min 66 min. flow 64 64 1 r/min 62 min. 1 flow r/min 62 6 min. flow 6 58 58 56 56 54 54 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet (15) Pressure (22) ( (29) (36) Sound pressure data equivalent Sound pressure to NFPA. data equivalent to NFPA. Torque Torque Nm (in.lb.) Nm (in.lb.) Torque and Power at 18 r/min, 5C (12F), and 1. absolute ( psi gauge) Inlet Torque and Power at 18 r/min, 5C (12F), 6 (531) and 1. absolute ( psi gauge) Inlet 6 55 (531) (4867) 55 5 (4867) (4425) 5 45 (4425) (3982) Torque, 45 4 (3982) (354) Torque, 4 35 (354) (397) 35 3 (397) (2655) 15 (21) 3 25 (2655) (2212) Power, 15 125 (21) (168) 25 2 (2212) (177) Power, 125 1 (168) (134) 15 (1327) 2 (177) 1 75 (11) (134) 15 1 (1327) (885) Torque, 75 5 (11) (67) 5 (442) Cut-off 1 (885) Torque, 5 25 (67) (34) 5 (442) Cut-off 25 (34) 5 1 15 2 25 (7) (15) (22) (29) (36) 5 1 15 2 25 (7) Outlet (15) Pressure (22) ( (29) (36) Power Power kw (hp) kw (hp) Torque Torque Nm (in.lb.) Nm (in.lb.) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 73
Performance Quiet version, optimized for 1-18 rpm (E) PVM141 Delivery and Efficiency at 15 r/min, 5C (12F), and 1. absolute ( psi gauge) Inlet Delivery 1 and Efficiency at 15 r/min, 5C (12F), and 1. absolute ( psi gauge) Inlet Volumetric Efficiency 9 1 Volumetric Efficiency 89 78 67 56 45 34 23 12 1 5 1 15 2 (7) (15) (22) (29) 5Outlet Pressure 1 15 ( 2 (7) (15) (22) (29) 3 (79) 25 3 (66) (79) 2 25 (53) (66) 15 2 (4) (53) 1 15 (26) (4) 51 (13) (26) 5 (13) 25 (36) 25 (36) Delivery and Efficiency at 12 r/min, 5C (12F), Delivery and 1. and Efficiency absolute at (12 psi gauge) r/min, Inlet 5C (12F), and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency 9 Volumetric Efficiency 9 8 8 7 7 6 3 (79) 6 3 (79) 5 25 (66) 5 25 (66) 4 2 (53) 4 2 (53) 3 15 (4) 3 15 (4) 2 1 (26) 2 1 (26) 1 5 (13) 1 5 (13) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet Pressure (15) (22) ( (29) (36) Delivery Deliver and an 1 1 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 Power kw (hp) ), F), 1) 8) 1) 4) 68) ) 34) 1) ) ) Torque Nm (in.lb.) Torque Nm (in.lb.) Torque and Power at 15 r/min, 5C (12F), and 1. absolute ( psi gauge) Inlet Torque and Power at 15 r/min, 5C (12F), 6 (531) and 1. absolute ( psi gauge) Inlet 55 6 (4867) (531) 5 55 (4425) (4867) 45 (3982) (4425) 4 45 (354) (3982) 35 4 (397) (354) 3 35 (2655) (397) 25 3 (2212) (2655) 2 25 (177) (2212) 15 2 (1327) (177) 1 15 (885) (1327) 5 1 (442) (885) Torque, Torque, Power, Power, Power kw (hp) Power kw (hp) 15 (21) 125 15 (168) (21) 1 125 (134) (168) 751 (11) (134) 575 (67) (11) 25 (34) (67) 5 (442) 25 (34) 5 1 15 2 25 (7) (15) (22) (29) (36) 5 1 15 2 25 (7) Outlet (15) Pressure (22) ( (29) (36) Torque Nm (in.lb.) Torque Nm (in.lb.) Torque and Power at 12 r/min, 5C (12F), and Torque 1. and absolute Power at (12 psi gauge) r/min, Inlet 5C (12F), and 1. absolute ( psi gauge) Inlet 6 (531) 6 (531) 55 (4867) 55 (4867) 5 (4425) 5 (4425) 45 (3982) 45 (3982) 4 (354) Torque, 4 (354) Torque, 35 (397) 35 (397) 3 (2655) 15 (21) 3 (2655) 25 (2212) 15 (21) 125 (168) 25 (2212) 2 (177) 125 (168) 1 (134) 2 (177) 15 (1327) Power, 75 1 (11) (134) 15 (1327) Full Stroke Power, 1 (885) 75 (11) 5 (67) 1 (885) 5 (442) 5 (67) 25 (34) 5 (442) 25 (34) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 (36) 25 (7) Outlet Pressure (15) (22) ((29) (36) Power kw (hp) Power kw (hp) Torque Nm (in.lb.) Torque Nm (in.lb.) To a 6 (5 6 55 (4 5 55 (4 5 45 (3 4 45 (3 35 4 (3 3 35 (2 3 25 (2 2 25 (1 15 2 (1 1 15 ( 1 5 ( 5 74 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Performance Quiet version, optimized for 1-18 rpm (E) PVM141 9) ) 6) ) 3) ) ) ) 6) ) ) Delivery Delivery l/min l/min (USgpm) (USgpm) Delivery and Efficiency at 1 r/min, 5C (12F), Delivery and and 1. Efficiency absolute at 1 ( psi r/min, gauge) 5C Inlet (12F), and 1. absolute ( psi gauge) Inlet 1 1 Volumetric Efficiency 9 Volumetric Efficiency 9 8 8 7 7 6 3 (79) 6 3 (79) 5 25 (66) 5 25 (66) 4 2 (53) 4 2 (53) 3 15 (4) 3 15 (4) 2 1 (26) 2 1 (26) 1 5 (13) 1 5 (13) 5 1 15 2 25 (7) 5 (15) 1 (22) 15 (29) 2 25 (36) (7) (15) (22) (29) (36) Efficiency Efficiency % % Delivery Delivery l/min l/min (USgpm) (USgpm) Case Flow - l/min (USgpm) Case Flow Versus Outlet Pressure at Full Flow, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 7,6 (2.) 6,6 (1.75) 5,7 (1.5) 4,7 (1.25) 3,8 (1.) 2,8 (.75) 1,9 (.5),9 (.25) 5 1 15 2 25 (7) (15) (22) (29) (36) Outlet Pressure - ( 3 (44) 35 (5) F), F), Power Power kw kw (hp) (hp) (21) (21) 5 (168) (168) (134) (134) (11) 11) (67) 67) (34) 34) Torque Torque Nm Nm (in.lb.) (in.lb.) Torque and Power at 1 r/min, 5C (12F), Torque and 1. and Power absolute at 1 ( psi r/min, gauge) 5C Inlet (12F), and 1. absolute ( psi gauge) Inlet 6 (531) 6 (531) 55 (4867) 55 (4867) 5 (4425) 5 (4425) 45 (3982) Torque, 45 (3982) 4 (354) Torque, 4 (354) 35 (397) 35 (397) 3 (2655) 15 (21) 3 (2655) 15 (21) 25 (2212) 125 (168) 25 (2212) 125 (168) 2 (177) 1 (134) 2 (177) 1 (134) 15 (1327) Power, 75 (11) 15 (1327) Power, 75 (11) 1 (885) 5 (67) 1 (885) 5 (67) 5 (442) 25 (34) 5 (442) 25 (34) 5 1 15 2 25 5 (7) 1 (15) 15 (22) (29) 2 (36) 25 (7) (15) (22) (29) (36) Power Power kw kw (hp) (hp) Case Flow - l/min (USgpm) Case Flow Versus Outlet Pressure at Cutoff, 18 r/min 5 C (12 F) and 1. absolute ( psi gauge) Inlet 22,7 (6) 18,9 (5) 15,1 (4) 11,4 (3) 7,6 (2) 3.8 (1) 5 1 15 2 25 (7) (15) (22) (29) (36) Outlet Pressure - ( 3 (44) 35 (5) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 75
(%) (%) (%) Performance Higher speed version (M) PVM141 Noise Level dba Typical Typical Noise Noise Levels Levels at 2 at 2 and 1 and 1 r/min r/min with with Petroleum Petroleum Oil (1W) Oil (1W) at 93 C at 93 C (2 F), (2 F), Typical and and Noise Levels at 2 and 1 r/min 1. 1. absolute absolute ( psi ( gauge) psi gauge) Inlet with Inlet Petroleum Oil (1W) at 93 C (2 F), and 88 88 1. absolute ( psi gauge) Inlet 88 86 86 86 84 2 r/min 84 2 r/min min. flow min. flow 84 2 r/min 82 82 min. flow 82 8 8 8 78 2 r/min 78 2 r/min max. flow max. flow 78 2 r/min max. flow 76 76 76 74 74 1 r/min 1 r/min min. flow min. flow 74 1 r/min 72 72 min. flow 72 7 7 7 68 1 r/min 1 r/min 68 max. flow max. flow 1 r/min 68 66 66 max. flow 66 64 64 5 5 1 1 15 15 2 64 2 25 25 (7) (7) (15) (15)(22)(22) (29) (29) (36) 5 (36) 1 15 2 25 Outlet Outlet Pressure Pressure ( ( (7) (15) (22) (29) (36) Sound Sound pressure pressure data data equivalent equivalent to NFPA. to NFPA. Sound pressure data equivalent to NFPA. Noise Level dba Noise Level dba Overall Efficiency versus versus Speed Speed at 93 C at 93 C (2 F), (2 F), Delivery Delivery and Case and Case Flow Flow versus versus Speed Speed at at and 1. and 1. absolute absolute ( psi ( gauge) psi gauge) Inlet Overall Inlet Efficiency versus Speed 93 C 93 C (2 F), at 93 C (2 F), Full (2 F), Flow Full Flow and 1. and 1. absolute absolute Delivery and Case Flow ve and 1. absolute ( psi gauge) ( Inlet psi ( gauge) psi gauge) Inlet Inlet 93 C (2 F), Full Flow and 1 1 1 28 (74) 28 (74) ( psi gauge) In 1 28 (74) 95 26 (69) 95 26 (69) 95 26 (69) 24 (63) 24 (63) 1 9 1 (15 (15 1 1 9 24 (63) 9 1 (15 1 15 (22 22 (58) 22 (58) (15 (15 15 (22 85 22 (58) (15 85 Delivery Delivery 15 (22 85 5 2 (53) 5 2 (53) Delivery 5 2 (53) 8 21 (3 21 (3 8 21 (3 21 (3 (7 8 21 (7 (3 18 (48) 18 (48) 23 (33 (7 Delivery Delivery 23 (33 18 (48) 75 16 (42) 75 16 (42) Case 23 (33 Case 75 14 (37) 16 (42) 14 (37) Flow Flow l/min 7 14 (37) l/min 7 7 12 (32) 12 (32) (USgpm) (USgpm) 65 65 21 (3 12 (32) 1 (26) 21 (3 1 (26) 1 (2.6) 1 (2.6) 65 Case Flow Case Flow 21 (3 1 (26) 6 6 8 (21) 8 (21) 8 (2.1) 8 (2.1) Case 6 6 (16) 6 (16) 8 (21) 6 (1.6) 6 (1.6) 55 55 6 (16) 55 4 (11) 4 (11) 4 (1.1) 4 (1.1) 5 5 2 (5) 4 (11) 2 (5) 2 (.5) 2 (.5) 5 1 1 (15 (15 Case Flow Case Flow 2 (5) 1 (15 Cas 5 5 1 1 15 15 2 2 25 25 5 5 1 115 152 225 25 5 1 15 2 25 Speed (r/min) Speed (r/min) 5 1 15 Speed (r/min) Speed (r/min) Speed (r/min) Speed (r/min) 76 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Performance Higher speed version (M) PVM141 Torque Nm (in.lb.) Torque Torque Torque versus versus versus Speed Speed Speed at 93 C at at (2 F), at 93 C 93 C 93 C (2 F), (2 F), Full Flow Full Full and Full Flow Flow 1. Flow and and and 1. 1. absolute 1. absolute absolute ( psi ( ( gauge) ( psi psi psi gauge) gauge) Inlet Inlet Inlet Inlet 6 (531) 6 6 6 (531) (531) (531) 55 (4867) 55 55 55 (4867) (4867) (4867) 23 23 23 (33 23 (33 (33 (33 5 (4425) 5 5 5 (4425) (4425) (4425) 21 21 21 (3 21 (3 (3 (3 45 (3982) 45 45 45 (3982) (3982) (3982) 4 (354) 4 4 4 (354) (354) (354) 35 (2655) 35 35 35 (2655) (2655) 15 (2655) 15 15 (22 15 (22 (22 (22 3 (2655) 3 3 3 (2655) (2655) (2655) 25 (2212) 25 25 25 (2212) (2212) (2212) 1 1 1 (15 1 (15 (15 (15 2 (177) 2 2 2 (177) (177) (177) 15 (1327) 15 15 15 (1327) (1327) (1327) 1 (885) 1 1 1 (885) (885) (885) 5 (725 5 5 5 (725 (725 (725 5 (442) 5 5 (442) 5 (442) 17 (25 (442) 17 17 17 (25 (25 (25 5 5 5 1 5 1 1 15 1 15 15 2 15 2 2 25 2 25 25 3 25 3 3 3 Speed (r/min) Speed Speed Speed (r/min) (r/min) (r/min) Torque Nm (in.lb.) Torque Nm Nm (in.lb.) Power kw (hp) Power Power Power versus versus versus Speed, Speed, Speed, 93 C (2 F), 93 C 93 C 93 C (2 F), (2 F), and 1. and and and 1. 1. absolute 1. absolute absolute ( psi ( ( gauge) ( psi psi psi gauge) gauge) Inlet Inlet Inlet Inlet 12 (161) 12 12 12 (161) (161) (161) 23 23 23 23 11 (148) 11 11 11 (148) (148) (33 (148) (33 (33 (33 21 1 (134) 21 21 21 1 1 1 (134) (134) (134) (3 (3 (3 (3 9 (121) 9 9 9 (121) (121) (121) 8 (17) 8 8 8 (17) (17) (17) 15 15 15 15 (22 (22 (22 (22 7 (94) 7 7 7 (94) (94) (94) 6 (8) 6 6 6 (8) (8) (8) 1 1 1 1 5 (67) 5 5 5 (67) (67) (67) (15 (15 (15 (15 4 (54) 4 4 4 (54) (54) (54) 3 (4) 5 3 3 3 (4) (4) (4) 5 5 5 (7 (7 (7 (7 2 (27) 2 2 2 (27) (27) (27) 17 17 17 17 1 (13) 1 1 1 (13) (13) (13) (25 (25 (25 (25 Power kw (hp) Power kw kw (hp) (hp) 5 5 51 5 1 115 1 15 152 15 2 225 2 25 25 25 Speed (r/min) Speed Speed Speed (r/min) (r/min) (r/min) Torque Nm (in.lb.) Torque Torque Torque and Case and and Flow and Case Case versus Case Flow Flow Flow versus versus Speed Speed Speed at 93 C at at at 93 C 93 C 93 C (2 F), (2 F), (2 F), Load Sense Load Load Load Sense Sense Standby Standby Standby 1. and and and 1. 1. absolute 1. absolute absolute ( psi ( ( gauge) ( psi psi psi gauge) gauge) Inlet Inlet Inlet Inlet 14 (124) 14 14 (124) 14 (124) (124) 13 (115) 13 13 (115) 13 (115) (115) 12 (16) 2 (29 12 12 (16) 12 (16) (16) 2 2 2 (29 (29 (29 diff. diff. diff. Torque diff. Torque Torque 11 (97) Torque 11 11 (97) 11 (97) (97) 1 (89) 11 (16 1 1 (89) 1 (89) (89) 11 11 11 (16 (16 (16 diff. diff. diff. Torque diff. Torque Torque Torque Case 9 (8) Case Case Case 9 (8) 9 (8) (8) Flow l/min Flow Flow Flow l/min l/min 8 (71) l/min 8 (71) 8 (71) (71) (USgpm) (USgpm) (USgpm) 7 (62) 7 (62) 7 (62) (62) 6.5 (1.72) 6.5 6.5 6.5 (1.72) (1.72) (1.72) 6 (53) 2 (29 6 (53) 6 (53) (53) 2 2 2 (29 (29 (29 diff. Case diff. diff. Flow diff. Case Case Case Flow Flow 6. (1.58) Flow 6. 6. 6. (1.58) (1.58) (1.58) 5 (44) 5 (44) 5 (44) (44) 5.5 (1.45) 5.5 5.5 5.5 (1.45) (1.45) (1.45) 4 (35) 4 (35) 4 (35) (35) 5. (1.32) 5. 5. 5. (1.32) (1.32) (1.32) 3 (27) 3 (27) 3 (27) 4.5 (1.19) (27) 4.5 4.5 4.5 (1.19) (1.19) (1.19) 2 (18) 11 (16 2 (18) 2 (18) (18) 11 11 11 (16 (16 (16 4. (1.6) diff. Case 4. 4. 4. (1.6) (1.6) (1.6) diff. diff. Flow diff. Case Case Case Flow Flow 1 (9) Flow 1 (9) 1 (9) 3.5 (.92) (9) 3.5 3.5 3.5 (.92) (.92) (.92) 3. (.79) 3. 3. 3. (.79) (.79) (.79) 5 5 5 1 5 1 1 15 1 15 15 2 15 2 2 25 2 25 25 25 Speed (r/min) Speed Speed Speed (r/min) (r/min) (r/min) Torque Nm (in.lb.) Torque Nm Nm (in.lb.) Torque Nm (in.lb.) Torque Torque Torque and Case and and Flow and Case Case versus Case Flow Flow Flow versus versus Speed Speed Speed at 93 C at at (2 F), at 93 C 93 C 93 C (2 F), (2 F), Pressure Pressure Pressure Limit Limit Limit Cut-Off Limit Cut-Off Cut-Off and and and and 1. 1. 1. absolute 1. absolute absolute ( psi ( ( gauge) ( psi psi psi gauge) gauge) Inlet Inlet Inlet Inlet 11 (973) 11 11 11 (973) (973) (973) 1 (885) 1 1 1 (885) (885) (885) 9 (796) 9 9 (796) 9 (796) (796) 21 21 21 (3 21 (3 (3 (3 8 (78) 8 8 (78) 8 (78) (78) Torque Torque Torque Torque 15 15 (22 7 (619) 7 (619) 15 15 (22 7 (619) (22 (22 7 (619) Torque Torque Torque Torque 6 (531) 6 6 (531) 6 (531) Case Flow (531) Case Case Case Flow Flow l/min Flow l/min l/min l/min 5 (442) 5 5 (442) 5 (442) (USgpm) (442) (USgpm) (USgpm) 4 (354) 4 4 (354) 4 (354) 2 (5.3) (354) 2 2 2 (5.3) (5.3) (5.3) 21 21 21 (3 21 (3 (3 (3 3 (265) 3 3 (265) 3 (265) (265) Case Flow 15 (2.6) Case Case Case Flow Flow Flow 15 15 15 (2.6) (2.6) (2.6) 2 (177) 2 2 (177) 2 (177) 15 (177) 15 15 (22 15 (22 (22 (22 1 (4.) 1 1 1 (4.) (4.) (4.) Case Flow Case Case Case Flow Flow 1 (88) Flow 1 1 (88) 1 (88) 5 (1.3) (88) 5 (1.3) 5 (1.3) (1.3) 5 5 51 5 1 1 15 1 15 15 2 15 2 2 25 2 25 25 25 Speed (r/min) Speed Speed Speed (r/min) (r/min) (r/min) Torque Nm (in.lb.) Torque Nm Nm (in.lb.) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 77
End-ported Models PVM18/2 Dimensions in millimeters (inches) Drain port F (See options on page 17.) See shaft options starting on page 12. E Alt. drain port F. (See options on page 17.) Load sense port J. (See options on page 17.) 72, (2.83) 58, (2.28) 72, (2.83) 58, (2.28) 73, (2.87) 76, (2.99) Control position for right hand (clockwise) shaft rotation, as viewed from shaft end. Position for left hand rotation is shown on following page. F G (with adj. max. stop) H (without adj. max. stop) Adjustable maximum displacement stop (1 turn = 1.1 cm 3 /rev). CCW reduces displacement. 37,4 (1.47) 165,7 (6.52) B M C D M 85,1 (3.35) 55,2 (2.17) A 23, (.91) J K L Inlet gauge port K. See options on page 17. Inlet port B. See options on page 16. Drain port F. See options on page 17. 34,5 (1.36) Outlet port C. See options on page 16. 34, (1.34) 78 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
End-ported Models PVM18/2 Dimensions in millimeters (inches) Dimensions in millimeters (inches) 37,4 (1.47) 37,4 (1.47) Adjustable maximum displacement stop Adjustable (1 turn = 1.1 maximum cm 3 /rev). displacement CCW reduces stop (1 displacement. turn = 1.1 cm 3 /rev). CCW reduces displacement. Inlet position for right hand rotation (Position for Inlet left hand position rotation for right shown hand below). rotation (Position for left hand rotation shown below). 165,7 (6.52) 165,7 (6.52) Control position for right hand rotation Control (Load position sensing for right control hand shown) rotation (Load sensing control shown) Outlet Outlet 34,5 34, (1.36) 34,5 (1.34) 34, (1.36) (1.34) Inlet/Outlet Ports and Control Positioned Inlet/Outlet for Right Ports Hand Rotation Control Positioned for Right Hand Rotation Control position for left hand rotation Control (Pressure position compensated for left hand control rotation shown) (Pressure compensated control shown) 37,5 (1.48) 37,5 (1.48) 14,5 (5.53) 14,5 (5.53) 126,3 (4.97) 126,3 (4.97) Outlet Outlet Inlet position for left hand rotation Inlet position (Position for for left right hand hand rotation (Position shown for above) right hand rotation shown above) Inlet/Outlet Ports and Control Positioned Inlet/Outlet for Left Ports Hand and Rotation Control Positioned for Left Hand Rotation EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 79
Side-ported Models PVM18/2 Dimensions in millimeters (inches) Load sense port J (See options on page 17) Alt. drain port F (See options on page 17) Drain port F (See options on page 17) E M C L outlet port C. Outlet port C. See options on page 16. See shaft options starting on page 12. 72, (2.83) To pilot mtg. flg. M N 72, (2.83) Control position for right hand (clockwise) shaft rotation, as viewed from shaft end. Position for left hand rotation is shown on following page. 58, (2.28) F G (with adj. max. stop) H (without adj. max. stop) Adjustable maximum displacement stop (1 turn = 1.1 cm 3 /rev). CCW reduces displacement. Outlet port C (above). See options on page 16. Inlet port B. See options on page 16. 114,7 (4.52) A B M C D M 85,1 (3.35) 55,2 (2.17) 18,8 (4.28) 23, (.91) Alt. drain port F. See options on page 17. J L K Inlet gauge port K. See options on page 17. 21,9 (.86) 62,9 (2.48) 21,6 (.85) 62,9 (2.48) Outlet gauge port K. See options on page 17. 8 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Side-ported Models PVM18/2 Dimensions in millimeters (inches) Adjustable maximum displacement stop (1 turn = 1.1 cm 3 /rev). CCW reduces displacement. 114,7 (4.52) Control position for right hand rotation (Load sensing control shown) Inlet position for right hand rotation (Position for left hand rotation shown below) Outlet gauge port K. See options on page 17. Inlet gauge port K. See options on page 17. Outlet 21,9 21,6 (.86) (.85) 62,9 62,9 (2.48) (2.48) Inlet/Outlet Ports and Control Positioned for Right Hand Rotation Control position for left hand rotation (Pressure compensated control shown) 86,5 (3.41) 72,3 (2.85) Outlet gauge port K. See options on page 17. Inlet gauge port K. Seep options on page 17. Outlet Inlet position for left hand rotation (Position for right hand rotation shown above) Inlet/Outlet Ports and Control Positioned for Left Hand Rotation EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 81
Thru-drive Models PVM18/2 Dimensions in millimeters (inches) Load sense port J (See options on page 17) Alt. drain port F (See options on page 17) Drain port F (See options on page 17) 124, (4.88) 164,2 (6.46) Centerline of outlet port Outlet port C. See options on page 16 See shaft options starting on page 17. 72, (2.83) to pilot mtg. flg. 164,2 (6.46) 72, (2.83) 58, (2.28) Control position for right hand (clockwise) shaft rotation, as viewed from shaft end. Position for left hand rotation is shown on following page. 26,1 (1.3) 221,4 (8.72) with adj. max. stop 212,3 (8.36) without adj. max. stop Adjustable maximum displacement stop (1 turn = 1.1 cm 3 /rev). CCW reduces displacement. Inlet port B. See options on page 16. 114,7 (4.52) A B 85,1 (3.35) 18,1 (4.14) 23, (.91) 6, (2.36) C M D M 99, (3.9) 167,7 (6.6) 223,2 (8.79) 62,9 (2.48) Alt. drain port F. See options on page 17. 64,2 (2.53) 82 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Thru-drive Models PVM18/2 Model Code Position 25 Description A For SAE A pad with a 9T, 16/32 DP, 3 pressure angle, involute spline B For SAE A pad with a 11T, 16/32 DP, 3 pressure angle, involute spline G For ISO 8 A2HW pad with a 9T SAE spline H For ISO 8 A2HW pad with a 11T SAE spline Dimensions in millimeters (inches) Adjustable maximum displacement stop (1 turn = 1.1 cm 3 /rev). CCW reduces displacement. Inlet position for right hand rotation (Position for left hand rotation shown below) 114,7 (4.52) Outlet Control position for right hand rotation (Load sensing control shown) Inlet/Outlet Ports and Control Positioned for Right Hand Rotation 62,9 (2.48) 64,2 (2.53) Control position for left hand rotation (Pressure compensator control shown) Output shaft 21T, 32/64 DP, 3 PA involute spline. 57,49 (2.26) 86,5 (3.41) 72,3 (2.85) 4,46 (1.59) 12,25 (.48) 27, (1.6) 79,4 (3.13) K (2 places) 53,5 (2.11) 159,2 (6.27) G 89,7 (3.531) 89,6 (3.527) 2, (.79) 1,9 (.75) Outlet H H Inlet position for left hand rotation (Position for right hand rotation shown above) Inlet/Outlet Ports and Control Positioned for Left Hand Rotation 8,5 (.33) N (2 places) 2, (.79) 2, (.79) Model Code Position 25 ØG H K N A,B 82,625 (3.253) 82,575 (3.251) 53,2 (2.9) 375-16 UNC-2B thd..75 deep min 375-16 UNC-2B thd..62 deep min. G,H 8,46 (3.151) M1 x 1,5 thd. M1 x 1,5 thd. 8,2 (3.15) 54,5 (2.15) 19,5 deep min 15,88 deep min. EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 83
Flange Designations PVM18/2 A Pilot Flange Designation ØA B C D E F G H J K L M SAE J744-82-2 82,55 11,35/1,97 16,4 53,2 Model Code A (3.25) (.447/.432) (4.19) (2.9) 131,5 33,6 228,9 219,8 16,5 166,7 2,7 65,2 ISO 319/2-8A2HW 8, 11,27/11, 19, 54,5 (5.18) (1.32) (9.) (8.65) (4.19) (6.56) (7.9) (2.57) Model Code B (3.15) (.444/.433) (4.29) (2.15) B Pilot Flange Designation SAE J744-11-2 11,6 14,55/14,17 146, 73, Model Code C (4.) (.572/.557) (5.75) (2.875) 124, 26,1 221,4 212,3 99, 159,2 193,9 87, ISO 319/2-1A2HW 1, 14,27/14, 14, 7, (4.88) (1.3) (8.72) (8.36) (3.9) (6.27) (7.63) (3.43) Model Code D (3.937) (.562/.551) (5.512) (2.756) Pilot Flange Designation ØA B C D SAE J744-127-2 Model Code C 11,6 (4.) 14,55/14,17 (.572/.558) 146, (5.75) 73, (2.87) ISO 319/2-1 A2HW Model Code D 1, (3.94) 14,27/14, (.562/.551) 14, (5.51) 7, (2.76) 84 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
End-ported Models PVM45/5 Dimensions in millimeters (inches) See shaft options starting on page 12. Drain port F. See options on page 17. Alternate drain port F Inlet gauge port K 8, (3.15) 28, (1.1) 8, (3.2) 8, (3.15) 8, (3.2) Adjustable maximum displacement stop (1 turn = 2 cm 3 /rev). 44,6 (1.75) Alternate load sense port J 36,9 (1.45) Control position for left hand (counterclockwise) shaft rotation, as viewed from shaft end. Position for right hand rotation is shown on following page. B 257, (1.12) max. 247, (9.72) 178,6 (7.3) 19,1 (.75) 134,3 (5.29) max. Load sensing control (See pressure compensated control on following page.) Load sense port J. See options on page 17. Inlet port B. See options on page 16. E 13,6 (5.14) 42, (1.65) C D 87, (3.425) 174, (6.85) A 135,4 (5.33) 47,8 (1.88) 175, (6.89) Alternate 75,1 212, (8.35) (2.96) drain port F Outlet gauge port K. See options on page 17. Outlet port C. See options on page 16. 87,1 (3.43) 53, (2.9) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 85
End-ported Models PVM45/5 Dimensions in millimeters (inches) Dimensions in millimeters (inches) 34,4 (1.35) 121,8 (4.8) max. Control position for left hand rotation Control position for Non-maximum left hand adjustment rotation stop control cap. See preceding Non-maximum page for adjustment adjustable maximum stop control displacement cap. See stop preceding page for adjustable Inlet position maximum for right displacement hand stop rotation (Position for left hand Inlet rotation position shown for right below) hand rotation (Position for left hand rotation shown below) 98,9 34,4 (3.89) (1.35) 98,9 (3.89) 121,8 (4.8) max. 4, (.16) Control position for right hand rotation (Pressure compensated 4, (.16) control Control shown) position for right hand rotation (Pressure compensated control shown) 138,5 (5.45) 138,5 (5.45) Outlet Outlet 53, 47,8 (1.88) (2.9) 87,1 75,1 53, 47,8 (1.88) (2.9) (3.43) (2.96) 87,1 75,1 Inlet/Outlet Ports (3.43) and Control (2.96) Positioned for Right Hand Rotation Inlet/Outlet Ports and Control Positioned for Right Hand Rotation Control position for left hand rotation (Load sensing Control control position shown) for left hand rotation (Load sensing control shown) Control position for right hand rotation Control position for right hand rotation Outlet Outlet Inlet/Outlet Ports and Control Positioned for Left Hand Rotation Dimensions Inlet/Outlet shown Ports and on preceding Control Positioned page. for Left Hand Rotation Dimensions shown on preceding page. Inlet position for left hand rotation (Position for right hand Inlet rotation position shown for left above) hand rotation (Position for right hand rotation shown above) 86 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Side-ported Models PVM45/5 Dimensions in millimeters (inches) 81,3 (3.2) Adjustable max. displacement stop (1 turn = 2 cm 3 /rev) Drain port F. See options on page 17. 36,9 (1.45) See shaft options starting on page 12. Inlet gauge port K Outlet gauge port K. See option on page 17. 81,3 (3.2) 134.3 (5.29) max. 57,5 (2.26) 5, (1.97) 72,5 (2.85) 69, (2.72) View Z-Z 257, (1.12) max. 168,2 (6.62) 75,5 (2.97) Load sensing control (See pressure compensated control on following page.) Alternate load sense port J 247, (9.72) 178,6 (7.3) 72,1 (2.84) 19,1 (4.3) 44,6 (1.75) 13,6 (5.14) Load sense port J. See options on page 17. 117,6 (4.63) E Control position for right hand (clockwise) shaft rotation, as viewed from shaft end. Position for left hand rotation is shown on following page. 19,1 (.75) B Z 42. (1.65) 23, (9.6) Outlet port C. See options on page 16. 183, (7.2) Alternate drain port F 78, (3.7) 28, (8.19) C D 87, (3.425) 174, (6.85) A 135,4 (5.33) 191,6 (7.54) Alternate drain port F Inlet port B. See options on page 16. Z 42. (1.65) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 87
Side-ported Models PVM45/5 Dimensions Dimensions in in millimeters millimeters (inches) (inches) 121,8 121,8 (4.8) (4.8) max. max. 34,4 34,4 (1.35) (1.35) Control Control position position for for left left hand hand 98,9 98,9 (3.89) (3.89) rotation (Pressure compensated 4, (.16) Control position for right hand rotation rotation (Pressure compensated 4, (.16) Control position for right hand rotation control shown). Inlet/outlet port (Inlet/outlet port positions for right hand control shown). Inlet/outlet port (Inlet/outlet port positions for right hand positions for left hand rotation rotation are shown on preceding page.) positions for left hand rotation rotation are shown on preceding page.) are are the the opposite opposite of of those those shown shown Non-maximum Non-maximum adjustment adjustment stop stop control control for for right right hand hand rotation rotation on on 138,5 cap. cap. See See preceding preceding page page for for adjustable adjustable preceding page. (5.45) 138,5 preceding page. (5.45) maximum maximum displacement displacement stop. stop. Outlet Outlet gauge gauge port port K. K. See See options options Inlet gauge on on page page 17. 17. Inlet gauge port port K K 57,5 57,5 (2.26) (2.26) 5, 5, (1.97) (1.97) 72,5 72,5 (2.85) (2.85) 69, 69, (2.72) (2.72) Inlet/Outlet Inlet/Outlet Ports and Control Positioned for Ports Left Hand and Control Rotation Positioned for Left Hand Rotation Control Control position position for for left left hand hand rotation rotation (Inlet/outlet (Inlet/outlet port port positions positions for for left left hand hand rotation rotation are are the the opposite opposite of of those those shown shown for for right right hand hand rotation rotation on on preceding preceding page.) page.) Inlet Inlet gauge gauge port port K K Control Control position position for for right right hand hand rotation rotation (Load (Load sensing sensing control control shown). shown). Inlet/outlet Inlet/outlet port port positions positions for for right right hand hand rotation rotation are are shown shown on on preceding preceding page. page. Outlet Outlet gauge gauge port port K. K. See See options options on on page page 17. 17. Inlet/Outlet Inlet/Outlet Ports Ports and and Control Control Positioned Positioned for for Right Right Hand Hand Rotation Rotation Dimensions Dimensions shown shown on on preceding preceding page. page. 88 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Thru-drive Models PVM45/5 Dimensions in millimeters (inches) 13,6 (5.14) 78,6 (3.9) Outlet port C. See options on page 16. 133,3 (5.25) 11,8 (4.36) View A-A C 87, (3.43) 28, (8.19) B 87, (3.43) 183, (7.2) 34,1 (1.34) 44,6 (1.76) See shaft options starting on page 12. D 81,3 (3.2) 81,3 (3.2) Load sense port J. See options on page 17. A 168,2 (6.62) Flange dependent 117,6 (4.63) 42, (1.65) Drain port F. See options on page 17. 197,7 (7.78) 135,8 (5.35) Alt. drain port F. See options on page 17. 68,8 (2.71) 72,3 (2.85) Drain port F. See options on page 17. 36,9 (1.45) 178,6 (7.3) 191,6 (7.54) 251, (9.88) 249, (9.8) 11, (.43) 138,5 (5.45) 121,8 (4.8) 98,9 (3.89) Control position for L.H. rotation Left Hand Rotation 34,4 (1.35) Control position for R.H. rotation Adjustable maximum displacement stop (1 turn = 2.1 cm 3 /rev) Load sense control position for L.H. rotation Inlet port B. See options on page 16. 5,4 (.21) 42, (1.65) Right Hand Rotation Load sense control position for R.H. rotation A A Outlet gauge port K Right Hand Rotation with Load Sensing Control and Tube Ports Inlet gauge port K. See options on page 17. 35, (1.38) 36, (1.42) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 89
Thru-drive Models PVM45/5 Dimensions in millimeters (inches) A Pad 61,74 (2.43) 4,4 (1.59) 12,24 (.482) Output shaft 26T, 32/64 DP, 3 PA involute spline. G 31,75 (1.25) 89,7 (3.531) 89,6 (3.527) N (2 places) H H Model Code Position 25 Description A For SAE A pad with a 9T, 16/32 DP, 3 pressure angle, involute spline B For SAE A pad with a 11T, 16/32 DP, 3 pressure angle, involute spline C For SAE B pad with a 13T, 16/32 DP, 3 pressure angle, involute spline D For SAE B pad with a 15T, 16/32 DP, 3 pressure angle, involute spline G For ISO 8-A2HW pad with a 9T SAE spline H For ISO 8-A2HW pad with a 11T SAE spline J For ISO 1-A2/B4HW pad with a 13T SAE spline B Pad 263,5 (1.37) Output shaft 26T, 32/64 DP, 3 PA involute spline. 276, (1.87) 86,49 (3.41) 1,28 (.4) 53, 53, (2.9) (2.9) K (2 places) J (2 places) L (4 places) 77,47 (3.5) 11,75 (.46) G 2, (.79) 1,9 (.75) 17,9 (4.248) 17,82 (4.244) 35,3 (1.39) 86, (3.39) 2 plcs 86, (3.39) 2 plcs H H J (2 places) K (2 places) N (2 places) M (4 places) Model Code Position 25 ØG H J K L M N A,B 82,58 (3.251) 82,52 (3.249) 53.2 (2.9).375-16 UNC-2B thd..6 deep min. G,H 8,46 (3.15) 8,2 (3.149) 54,5 (2.15) M1 thd. x 1,5 15, deep min. C,D 11,65 (4.2) 73, 44,9 89,8.5-13 UNC-2B thd..5-13 UNC-2B.5-13 UNC-2B 11,6 (4.) (2.87) (1.77) (3.54) 24.9 deep min. M12 x thd. thru M1 x thd. thru 1,5 thd. 24,9 deep min. 1,5 thd. thru M12 x 1,5 thd. thru J,K 1, (3.937) 99,946 (3.935) 7, (2.76) 44,2 (1.74) 88,38 (3.48) M12 thd. x 1,5 thd. 24,9 deep min. M1 x 1,5 thd. thru M12 x 1,5 thd. thru 9 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Flange Designations PVM45/5 Pilot Flange Designation ØA B C D E SAE J744-11-2 11,6/11,55 (4./3.998) 9,7/9,19 (.382/.362) 146, (5.75) 73, (2.875) 14,55/14,17 (.572/.557) ISO 319/2-1A2HW 1,/99,95 (3.937/3.935) 9,5/9, (.374/.354) 14, (5.512) 7, (2.756) 14,27/14, (.562/.551) Pilot Flange Designation ØA B C D SAE 2-bolt mount 11,6/11,55 (4./3.998) 73, (2.87) 146, (5.75) 14,55/14,17 (.572/.557) ISO 1 2-bolt mount 1,/99,95 (3.937/3.935) 7, (2.76) 14, (5.512) 14,27/14, (.562/.551) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 91
End-ported Models PVM57/63 Dimensions in millimeters (inches) See mounting flange options on page 11. See shaft options starting on page 12. 269,7 (1.62) w/o adj. max. stop 116, (4.57) 26,2 (8.12) 82,3 (3.24) 82,3 (3.24) Outlet port C. See options on page 16. SAE.5-13 UNC-2B thd. 1.6 deep min. ISO M12 x 1,75 thd. 29. deep min. 199,3 (7.85) 121,8 (4.8) 77,5 (3.5) 77,78 (3.6) 38,89 (1.53) 21,44 (.84) 42,88 (1.69) Left Hand Rotation, Tube Port with Pressure Compensator Inlet port B. See options on page 16. 88,7 (3.49) 254,3 (1,) 13,1 (.51) 75,7 (2.98) 165,6 (6.52) Right Hand Rotation, Flange Port with Load Sensing Control Inlet port B. See options on page 16. 52,38 (2.6) 26,19 (1.3) SAE.375-16 UNC-2B thd..88 deep min. ISO M1 x 1,5 thd. 23. deep min. 26,18 (1.3) Outlet port C. See options on page 16. 87, (3.43) Outlet gauge port K. Inlet gauge port K on opposite side. See options on page 17. 274,8 (1.82) Drain port F. Alternate drain port F on opposite side. See options on page 17. 292,2 (11.5) Load sense port J. See options on page 17. 21,4 (7.93) 245,4 (9.66) 168,2 (6.62) 32,9 (1.3) w/adj. max. stop 12,8 (4.5) 39, (1.54) 157, (6.18) 92 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Side-ported Models PVM57/63 Dimensions in millimeters (inches) See mounting flange options on page 11. See shaft options starting on page 12. 116, (4.57) 198,1 (7.8) 269,7 (1.62) w/o adj. max. stop 82,3 (3.24) Outlet gauge port K. See options on page 17. Inlet gauge port K. See options on page 17. 157, (6.18) 82,3 (3.24) Left Hand Rotation with Pressure Compensator 274,8 (1.82) 168,2 (6.62) 32,9 (1.3) Adjustable maximum displacement stop 1 turn = 2.98 l/min (.79 USgpm) Inlet port B. See options on page 16. Load sense port J. See options on page 17. 247,9 (9.76) 165,6 (6.52) Outlet port C. See options on page 16. 266,5 (1.49) 292,2 (11.5) w/adj. max. stop 213,4 (8.4) 241,5 (9.51) 224,4 (8.83) To mounting face 21,44 (.84) 42,88 (1.69) 38,89 (1.53) 77,78 (3.6) 199,3 (7.85) SAE.5-13 UNC-2B thd. 1.6 deep min. ISO M12 1,75 thd. 29. deep min. 121,8 (4.8) 77,5 (3.5) 61,5 (2.42) 75, (2.95) 75, (2.95) Right Hand Rotation with Load Sensing Control 57, (2.24) 87, (3.43) 52,37 (2.6) 26,2 (1.3) SAE.375-16 UNC-2B thd..88 deep min. ISO M1 x 1,5 thd. 23. deep min. 13,1 (.51) 26,19 (1.3) 12,8 (4.5) Drain port F. Alternate drain port F on opposite side. See options on page 17. 39, (1.54) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 93
Thru-drive Models PVM57/63 Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. 116, (4.57) 25, (8.7) S (See table next page) 44,8 (1.76) 8,1 (3.15) Alternate drain port F 82,3 (3.24) M12 thd. 21, deep (4 places) SAE.5-13 UNC-2B thd. 1.6 deep min. ISO M12 x 1,75 thd. 29. deep min. R Left Hand Rotation with Pressure Compensator and SAE 2-bolt A Flange (no adapter) Inlet port B. See options on page 16. T1 (2 places) 254,6 (1,) 165,6 (6.52) 157, (6.18) Load sense port J. See options on page 17. Outlet port C. See options on page 16. 292,2 (11.5) 168,2 (6.62) 284,4 (11.2) 213,4 (8.4) 32,9 (1.3) 82,3 (3.24) 224,4 (8.83) To mounting face 21,44 (.84) 42,88 (1.69) 77,78 (3.6) 38,89 (1.53) 199,3 (7.85) Inlet gauge port K. See options on page 17. 121,8 (4.8) 77,5 (3.5) 12, (.47) 89, (3.5) 14, (.55) 92, (3.62) Right Hand Rotation with Load Sensing Control and SAE 2-bolt A Flange (no adapter) 87, (3.43) 52,37 (2.6) 26,18 (1.3) Outlet gauge port K. See options on page 17. 13,1 (.52) 26,2 (1.3) SAE.375-16 UNC-2B thd..88 deep min. ISO M1 x 1,5 thd. 23. deep min. 12,8 (4.5) 39, (1.54) Drain port F. Alternate drain port F on opposite side. See options on page 17. 94 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Thru-drive Models PVM57/63 Dimensions in millimeters (inches) 68,7 (2.7) S Coupling Length Code SAE A, 9T 62,5 (2.46) A,G SAE B, 13T 93, (3.66) C,J SAE B-B, 15T 93, (3.66) D,K SAE C, 14T 93, (3.66) E,L B Adapter Flange To mounting face 39,9 (12.2) Coupling length (see table) Coupling (see table) T1 Model Code Position 25 Description A SAE A, 9T, 16/32 DP, 3 pressure angle, involute spline C SAE B, 13T, 16/32 DP, 3 pressure angle, involute spline D SAE B-B, 15T, 16/32 DP, 3 pressure angle, involute spline E SAE C, 14T, 12/24 DP, 3 pressure angle, involute spline G For ISO 8-A2HW pad with a 9T SAE spline J For ISO 1-A2/B4HW pad with a 13T SAE spline K For ISO 1-A2/B4HW pad with a 15T SAE spline L For ISO 125-A2/B4HW pad with a 14T SAE spline 35, (1.38) (4 plcs) T2 297,4 (11.7) To mounting face V Support mounting point (4 plcs) R 92, (3.62) Right hand rotation with Load Sensing Control and SAE 2-/4-bolt B adapter flange Support Model Code Position 25 Pilot Dia. Pilot Depth 2-bolt 4-bolt Mounting Points Flange Bolt R S T1 T2 V A,B SAE A 2-bolt SAE Ø82,65 (3.25±.1) 8,6/8,1 (.32/.34).375-16 UNC-2B thd. N/A N/A G,H ISO 8 ISO Ø8,5 (3.15) 9,/8, (.35/.31) M1 thd. N/A N/A C,D SAE B 2-/4-bolt SAE Ø11,65 (4.2±.1) 12,5/11,5 (.49/.45).5-13 UNC-2B thd..5-13 UNC-2B thd..5-13 UNC-2B thd..98 deep J,K ISO 1 ISO Ø1,5 (3.94) 12,5/11,5 (.49/.45) M12 thd. M12 thd. M12 thd. x 25, deep EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 95
Thru-drive Models PVM57/63 Dimensions in millimeters (inches) C Adapter Flange To mtg, face 297,4 (11.7) R 92, (3.62) W (4 plcs) 17, (4.21) 35, (1.38) (4 plcs) To mtg. face 39,9 (12.2) T1 T2 Left hand rotation with Pressure Compensator and SAE 2-/4-bolt C Adapter Flange Support Model Code Position 25 Pilot Dia. Pilot Depth 2-bolt 4-bolt Mounting Points Flange Bolt R S T1 T2 V E,F SAE C 2-/4-bolt SAE Ø127,5 (5.2±.1) 15,5/14,5 (.61/.57).625-11 UNC-2B thd..5-13 UNC-2B thd..5-13 UNC-2B thd..98 deep L,M ISO 125 ISO Ø125,5 (4.92) 15,5/14,5 (.61/.57) M16 thd. M12 thd. M12 thd. x 25, deep 96 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Side-ported Models PVM74/81 *Right Hand Only Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. 12, (4.2) Lifting point.375-16 UNC thd. 1, (.39) deep with SAE drain M1 thd. 1, (.39) deep with ISO drain Alt. drain port "F". See options on page 17. Alt. drain port "F". See options on page 17. Outlet port "C". See options on page 16. Inlet port "B". See options on page 16. 87, (3.42) 2X Outlet gauge port "K". See options on page 17. Inlet port "B". See options on page 16. TO MOUNTING FACE 249,6 (9.83) Alt. drain port "F". See options on page 17. Left hand rotation with Pressure Compensator 86, (3.39) 86, (3.39) Inlet gauge port "K". See options on page 17. Inlet gauge port "K". See options on page 17. Max. Adj. stop. One rotation will change displacement 6,1-6,8 l/min (1.6-1.8 USgpm) at 18 rpm 65, (2.56) 92, (3.62) 114, (4.49) 4,3 (.17) 91, (3.58) 143,3 (5.64) 114, (4.49) Right hand rotation with Load Sensing Control 65, (2.56) 191.8 (7.55) Load sense port "J". See options on page 17. Outlet gauge port "K". See options on page 17. 11, (4.33) 16,8 (.66) Outlet port "C". See options on page 16. Drain port "F". See options on page 17. Load Sense Port 9/16-18 UNF - 2A THRD (ORS PORT) 113,6 (4.47) 319,1 w/o max adj stop (12.56) 334,8 (13.18) 194,8 ( 7.67 ) 146,1 ( 5.75 ) C/G location 246,6 (9.71) 279,6 (11.1) 288, (11.34) 181,6 (7.15) 158 (6.22) 33,9 (1.33) 33, (1.3) 11 (4.33) 2.7 (7.9) (Max length For Min Torque Setting) Right hand rotation with Power/Torque limiter control PVM74/18 is not available with left hand rotation in any port configuration. EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 97
Thru-drive Models PVM74/81 *Right-hand only Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. 12, (4.2) Lifting point.375-16 UNC thd. 1, (.39) deep with SAE drain M1 thd. 1, (.39) deep with ISO drain Alt. drain port "F". See options on page 17. Alt. drain port "F". See options on page 17. Outlet port "C". See options on page 16. Inlet port "B". See options on page 16. 87, (3.42) 2X Outlet gauge port "K". See options on page 17. Inlet port "B". See options on page 16. TO MOUNTING FACE 249,6 (9.83) Left hand rotation with Pressure Compensator Inlet gauge port "K". See options on page 17. Max. Adj. stop. One rotation will change displacement 6,1-7,4 l/min (1.7-1.9 USgpm) at 18 rpm 4,8 (.16) 143,3 (5.64) Load sense port "J". See options on page 17. 334,8 (13.18) 319,1 (12.56) 113,6 (4.47) w/o max adj stop 194,8 (7.67) 146,1 (5.75) C/G location 33,9 (1.33) Alt. drain port "F". See options on page 17. 86, (3.39) 86, (3.39) Inlet gauge port "K". See options on page 17. 2X T1 92, (3.62) "A2" 45, (1.77) 91, (3.58) 114, 114, (4.49) (4.49) Right hand rotation with Load Sensing Control and 2-bolt A flange Outlet gauge port "K". See options on page 17. 11, (4.33) Outlet port "C". See options on page 16. Drain port "F". See options on page 17. 14.5 (.57) 277,6 (1.93) 322.6 (12.7) 246,6 (9.71) 181,6 (7.15) 33, (1.3) PVM74/18 is not available with left hand rotation in any port configuration. 98 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Thru-drive Models PVM74/81 *Right-hand only Dimensions in millimeters (inches) 68,3 (2.69) S R3 43,3 (1.7) S R3 Coupling Length Code SAE A, 9T 64,5 (2.54) A,G SAE A, 11T 65,3 (2.57) B,H SAE B, 13T 95,3 (3.75) C,J SAE B-B, 15T 95,3 (3.75) D,K SAE C, 14T 95,3 (3.75) E,L SAE C-C, 17T 91,8 (3.61) F,M R1 R2" R1 R2 Coupling length (See table) B Adapter Flange To mtg, face To mtg, face With adapter plate 372,6 (14.68) 335,1 (13.19) View rotated 9 4X 35, (1.38) 4X W Coupling (see table) 25, (.98) A1 92, (3.62) Without adapter plate A2 Coupling (see table) Coupling length (see table) A1 Right hand rotation with Load Sensing Control and ISO or SAE 2-/4-bolt B adapter flange T2 T1 Model code Position 25 Description A SAE A, 9T, 16/32 DP, 3 pressure angle, involute spline B SAE A, 11T, 16/32 DP, 3 pressure angle, involute spline C SAE B, 13T, 16/32 DP, 3 pressure angle, involute spline D SAE B-B, 15T, 16/32 DP, 3 pressure angle, involute spline E SAE C, 14T, 12/24 DP, 3 pressure angle, involute spline F SAE C-C, 17T, 12/24 DP, 3 pressure angle, involute spline G For ISO 8-A2HW pad with a 9T SAE spline H For ISO 8-A2HW pad with a 11 T SAE spline J For ISO 1-A2/B4HW pad with a 13T SAE spline K For ISO 1-A2/B4HW pad with a 15T SAE spline L For ISO 125-A2/B4HW pad with a 14T SAE spline M For ISO 125-A2/B4HW pad with a 17T SAE spline Model Code Position 25 Pilot O-ring O-ring Pilot Support Flange Bolt Dia. Dia. Depth Depth 2-bolt 4-bolt Mounting Points 4-bolt 2-bolt R1 R2 R3 S T1 T2 W A1 A2 A,B SAE A SAE Ø82,6 Ø89,65 2, (.8) 9,/8, 375-16 UNC-2B thd. N/A N/A N/A 53,2 G,H 2-bolt (3.25) (3.53) 1,9 (.7) (.35/.31) ISO 8 ISO Ø8,5 Ø89,75 2,7 (.11) 9,/8, M1 thd. N/A N/A N/A 54,5 (3.15) (3.53) 2,6 (.1) (.35/.31) (2.15) C,D SAE B SAE Ø11,65 Ø18,5 2, (.8) 12,5/11,5.5-13 UNC-2B thd..5-13 UNC-2B thd..5-13 UNC-2B 44,9 73, J,K 2-/4-bolt (4.) (4.25) 1,9 (.7) (.49/.45) thd..98 deep(1.77) (2.87) ISO 1 ISO Ø1,5 Ø18,75 2,7 (.11) 12,5/11,5 M12 thd. M1 thd. M12 thd. 25, deep 44,19 7, (3.94) (4.28) 2,6 (.1) (.49/.45) (1.74) (2.76) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 99
Thru-drive Models PVM74/81 *Right-hand only Dimensions in millimeters (inches) C Adapter Flange To mtg, face 347,6 (13.69) 4X 35, (1.38) 4X W T1 A1 92, (3.62) To mtg, face 335,1 (13.19) T2 A1 A2 View rotated 9 Left hand rotation with Pressure Compensator and ISO or SAE 2-/4-bolt C Adapter Flange Model Code Position 25 Pilot O-ring O-ring Pilot Support Flange Bolt Dia. Dia. Depth Depth 2-bolt 4-bolt Mounting Points R1 R2 R3 S T1 T2 W A1 A2 E,F SAE C SAE Ø127,5 Ø133,45 2, (.8) 15,5/14,5.625-11 UNC-2B thd..5-13 UNC-2B thd..5-13 UNC-2B 57,25 9,5 L,M 2-/4-bolt thd..98 deep (2.25) (3.56) ISO 125 ISO Ø125,5 Ø133,75 2,7 (.11) 15,5/14,5 M16 thd. M12 thd. M12 thd. 25, deep 56,57 9, (4.92) (3.26) 2,6 (.1) (.61/.57) (2.23) (3.54) 1 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Side-ported Models PVM98/16 Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. 121, (4.76) Alt. drain port F. See options on page 17. Lifting point.375-16 UNC thd.1, (.39) deep with SAE drain M1 thd. 1, (.39) deep with ISO drain Alt. drain port F. See options on page 17. 2X 95, (3.74) Outlet port C. See options on page 16. Outlet gauge port K. See options on page 17. Left hand rotation with Pressure Compensator Inlet port B. See options on page 16. Inlet gauge port K. See options on page 17. 162, (6.38) 342,4 (13.48) 115,5 (4.55) w/o max adj stop 357,8 (14.9) 33,9 (1.33) Inlet port B. See options on page 16. To mounting face 276,9 (1.9) Max. Adj. stop. One rotation will change displacement 7,9-8,7 l/min (2.1-2.3 USgpm) at 18 rpm Inlet gauge port K. See options on page 17. 16,4 (.65) 17,6 (6.72) Load sense port J. See options on page 17. 214,6 (8.45) 155,7 (6.13) C/G location 92,5 (3.64) 9, (3.54) Outlet gauge port K. See options on page 17. 17,5 (4.23) 35,5 (1.4) Outlet port C. See options on page 16. 37, (1.46) Alt. drain port F. See options on page 17. 7, 7, (2.76) (2.76) 98, 91, (3.86) (3.58) 119, 119, (4.69) (4.69) Left hand rotation with Load Sensing Control Drain port F. See options on page 17. 266,9 (1.51) 322,6 (12.7) 2X 194,5 (7.66) 35,6 (12.3) PVM98/16 is not available in left hand rotation with rear ports. EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 11
Thru-drive Models PVM98/16 Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. 121, (4.76) Alt. drain port "F". See options on page 17. Lifting point.375-16 UNC thd. 1, (.39) deep with SAE drain M1 thd. 1, (.39) deep with ISO drain Alt. drain port "F". See options on page 17. 347,9 (13.7) 2X 95, (3.74) Outlet port "C". See options on page 16. Inlet port "B". See options on page 16. 162, (6.38) Outlet gauge port "K". See options on page 17. Left hand rotation with Pressure Compensator Inlet gauge port "K". See options on page 14. 342,4 (13.48) 115,5 (4.55) w/o max adj stop 357,8 (14.9) 33,9 (1.33) Inlet port "B". See options on page 16. To mounting face 276,9 (1.9) 92,5 (3.64) Max. Adj. stop. One rotation will change displacement 7,9-8,7 l/min (2.1-2.3 USgpm) at 18 rpm 2X T1 17,3 (.68) 17,6 (6.72) Outlet gauge port "K". See options on page 17. Load sense port "J". See options on page 17. 15, (5.91) 36,6 (1.44) 17,5 (4.23) 214,6 (8.45) 164,4 (6.47) C/G location 2X 37, (1.46) 9, (3.54) 42, (1.65) Alt. drain port "F". See options on page 17. Inlet gauge port "K". See options on page 17. A2* 98, (3.86) 119, (4.69) 45, (1.77) 91, (3.58) 119, (4.69) Right hand rotation with 2-bolt A flange and Load Sensing Control Outlet port "C". See options on page 16. Drain port "F". See options on page 17. 266,9 (1.51) 2X 194,5 (7.66) PVM98/16 is not available in left hand rotation with rear ports. 12 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Thru-drive Models PVM98/16 Dimensions in millimeters (inches) 68,3 (2.69) S Coupling length (see table) B Adaptor Flange With adapter plate To mtg, face B Adapter 372,6Flange (14.68) 372,9 To mtg, face (14.68) To mtg, face 36,4 To mtg, face (14.19) 36,4 (14.19) View Rotated 9 View Rotated 9 35, 4X (1.38) 35, (1.38) (4 plcs) R3 4X W Support mounting points COMBINE R1 R2 WITH EXISTING GRAPHIC FOR THIS PAGE Coupling (see table) 25, (.98) 92, (3.62) V Support mounting points (4 plcs) A1 92, (3.62) 43,3 (1.7) S A1 A2 R3 Without adapter plate R1 R2 Coupling (see table) Coupling length (see table) A1 T1 T2 Right hand rotation A1 with Load Sensing Control A2 Right hand rotation with CV compensation and ISO or SAE 2-/4-bolt B adapter flange T2 T1 Coupling Length Code SAE A, 9T 64,5 (2.54) A,G SAE A, 11T 65,3 (2.57) B,H SAE B, 13T 95,3 (3.75) C,J SAE B-B, 15T 95,3 (3.75) D,K SAE C, 14T 95,3 (3.75) E,L SAE C-C, 17T 91,8 (3.61) F,M Model Code Position 25 Description A SAE A, 9T, 16/32 DP, 3 pressure angle, involute spline B SAE A, 11T, 16/32 DP, 3 pressure angle, involute spline C SAE B, 13T, 16/32 DP, 3 pressure angle, involute spline D SAE B-B, 15T, 16/32 DP, 3 pressure angle, involute spline E SAE C, 14T, 12/24 DP, 3 pressure angle, involute spline F SAE C-C, 17T, 12/24 DP, 3 pressure angle, involute spline G For ISO 8-A2HW pad with a 9T SAE spline H For ISO 8-A2HW pad with a 11 T SAE spline J For ISO 1-A2/B4HW pad with a 13T SAE spline K For ISO 1-A2/B4HW pad with a 15T SAE spline L For ISO 125-A2/B4HW pad with a 14T SAE spline M For ISO 125-A2/B4HW pad with a 17T SAE spline Model Code Position 25 Pilot O-ring O-ring Pilot Support Flange Bolt Dia. Dia. Depth Depth 2-bolt 4-bolt Mounting Points 4-bolt 2-bolt R1 R2 R3 S T1 T2 W A1 A2 A,B SAE A SAE Ø82,6 Ø89,65 2, (.8) 9,/8, 375-16 UNC-2B N/A N/A N/A 53,2 G,H 2-bolt (3.25) (3.53) 1,9 (.7) (.35/.31) thd..59 deep ISO 8 ISO Ø8,5 Ø89,75 2,7 (.11) 9,/8, M1 thd. N/A N/A N/A 54,5 (3.15) (3.53) 2,6 (.1) (.35/.31) x 18, deep (2.15) C,D SAE B SAE Ø11,65 Ø18,5 2, (.8) 12,5/11,5.5-13 UNC-2B thd..5-13 UNC-2B thd..5-13 UNC-2B 44,9 73, J,K 2-/4-bolt (4.) (4.25) 1,9 (.7) (.49/.45) thd..98 deep (1.77) (2.87) ISO 1 ISO Ø1,5 Ø18,75 2,7 (.11) 12,5/11,5 M12 thd. M1 thd. M12 thd. 25, deep 44,19 7, (3.94) (4.28) 2,6 (.1) (.49/.45) (1.74) (2.76) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 13
Thru-drive Models PVM98/16 Dimensions in millimeters (inches) C Adapter Flange To mtg, face 372,9 (14.68) 4X 35, (1.38) 4X W Support mounting points T1 T2 A1 92, (3.62) To mtg, face 36,4 (14.19) View Rotated 9 A1 A2 Left hand rotation with Pressure Compensator and ISO or SAE 2-/4-bolt C adapter flange Model Code Position 25 Pilot O-ring O-ring Pilot Support Flange Bolt Dia. Dia. Depth Depth 2-bolt 4-bolt Mounting Points R1 R2 R3 S T1 T2 W A1 A2 E,F SAE C SAE Ø127,5 Ø133,45 2, (.8) 15,5/14,5.625-11 UNC-2B thd..5-13 UNC-2B thd..5-13 UNC-2B 57,25 9,5 L,M 2-/4-bolt thd..98 deep (2.25) (3.56) ISO 125 ISO Ø125,5 Ø133,75 2,7 (.11) 15,5/14,5 M16 thd. M12 thd. M12 thd. 56,57 9, (4.92) (3.26) 2,6 (.1) (.61/.57) 25, deep (2.23) (3.54) 14 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
End-ported Models PVM131/141 Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. 369,4 (14.54) 34, (1.34) 23,4 (9.7) 132,7 (5.22) 131, (5.16) B inlet port 172, (6.77) C outlet port Optional drain port F 115, (4.53) Adjustable maximum stop option. Torque locknut to 37-45 Nm (27-33 lb ft). One turn of screw wil change pump displacement 5,7 cm 3 /rev (.35 in 3 /rev). Turn CCW to destroke. K Outlet gage port Left hand rotation with Pressure Compensator K Inlet gage port 65, (2.56) 2 plcs. 55, (2.17) 2 plcs. 143,5 (5.65) 111,5 (4.39) 2 plcs. 346,1 (13.63) max. length w/o max. adj. stop 122,6 (4.83) 2 plcs. K Inlet gage port F2 B inlet port B2 4 plcs. 132,7 (5.22) 11,5 (4.35) R.H. 94,5 (3.72) L.H. J Load sense signal port 18,6 (7.11) 55, (2.17) F3 F drain port 192,6 (7.58) 2 plcs. Optional drain port F 33,6 (13.2) Lifting point.5-13 UNC-2B thd. 18, (.79) dp. 2 plcs. 25, (.98) 16, (4.17) K Inlet gage port 49,7 (1.95) 64, (2.52) 14,2 (4.1) 91,5 (3.6) Right hand rotation with Load Sensing Control K Outlet gage port C outlet port C2 4 plcs. EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 15
Side-ported Models PVM131/141 Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. C outlet port C2 4 plcs. 341,1 (13.43) gage port spotface 318,1 (12.52) gage port spotface 28,4 (11.4) ref. View A - A Outlet port 65, (2.56) 2 plcs. 111,5 (4.39) 2 plcs. 172, (6.77) 115, (4.53) 34, (1.34) 369,4 (14.54) 28,4 (11.4) C L outlet 23,4 (9.7) port Optional drain port F 346,1 (13.63) max. length w/o max. adj. stop 1, (3.94) Adjustable maximum stop option. Torque locknut to 37-45 Nm (27-33 lb ft). One turn of screw will change pump displacement 5,7 cm 3 /rev (.35 in 3 /rev) 55, (2.16) 2 plcs. 122,6 (4.82) 2 plcs. 132,7 (5.22) 131, (5.16) Outlet gage port K Outlet port C. Inlet gage port K Inlet gage port K Left hand rotation with Pressure Compensator 132,7 (5.22) 11,5 (4.35) R.H. 94,5 (3.72) L.H. J Load sense signal port 18,6 (7.11) Inlet port B 143,5 (5.7) F2 A 55, (2.17) F3 Optional drain port F F drain port Lifting point.5-13 UNC-2B thd. 18. (.79) dp. 2 plcs. 192,6 (7.58) 2 plcs. 298.6 (11.76) B2 4 plcs. Inlet port B 16, (4.17) 7, (2.76) 7, (2.76) 95. (3.74) A Outlet gage port K 85 (7.28) 221.6 (8.73) (Max length For Min Torque Setting) Right hand rotation with Load Sensing Control 22.8 (8.69) Load Sense Port 9/16-18 UNF - 2A THRD (ORS PORT) 11.5 (4.35) Right hand rotation with Power/Torque limiter control 16 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Thru-drive Models PVM131/141 Dimensions in millimeters (inches) See pilot flange options on page 11. See shaft options starting on page 12. 172, (6.77) 143,5 (5.65) 34, (1.33) 23,4 (9.7) Drain port F. See options on page 17. 122,6 (4.83) 28,4 (11.4) 347,1 (13.67) 44,7 (1.76) 369,4 (14.54) 346,1 (13.63) w/o max. adj. stop CL outlet port 8, (3.15) See coupling code below See output shaft below 8,5 (.33) 14, (.55) A9 19, (.75) A11 Outlet port C. See options on page 16. Q See table below Inlet port B. See options on page 16. 132,7 (5.22) Q2 See table below SAE port 116,1 (4.57) ISO port 15, (5.91) 111,5 (4.39) 131, (5.16) Left Hand Rotation with Pressure Compensator and SAE 2-bolt A Flange (no adapter) Load sense port J. See options on page 17. 18,6 (7.11) Inlet port B. See options on page 16. SAE.5-13 UNC-2B thd. 1. deep min. or ISO M12 x 27. deep min. Outlet port C. See options on page 16. 65, (2.56) 15, (.59) 55, (2.16) 132,7 (5.22) 28,4 (11.4) 55, (2.17) 173, (6.81) 192,6 (7.58) 35,6 (12.3) 298,6 (11.76) Inlet gage port K 54,5 (2.15) 16, (4.17) 11,5 (.45) Inlet gage port K. See options on page 17. SAE.5-13 UNC-2B thd. 1.19 deep min. or ISO M12 x 31. deep min. 1, (3.94) 95, (3.74) 4, (1.57) 4, (.16) 45, (1.77) SAE port 116,1 (4.57) ISO port 15, (5.91) 313,6 (12.35) Alt. drain port F. See options on page 17. Outlet gage port K. See options on page 17. Right Hand Rotation with Load Sensing Control and SAE 2-bolt A Flange (no adapter) Model Code Position 25 Q1 Thru-drive Flange Q2 2-bolt Thread A,B SAE J744-82-2.375-16 UNC-2B Ø82.625/82.575 bore thd..8 deep G,H ISO 319/2-8A2 Ø8.75/8.25 bore M1 thd. x 18, deep EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 17
Thru-drive Models PVM131/141 Dimensions in millimeters (inches) 69,7 (2.74) O-ring (furnished) Coupling (See table) Model Code Position 25 Description A For SAE A pad with a 9T, 16/32 DP, 3 pressure angle, involute spline B For SAE A pad with a 11T, 16/32 DP, 3 pressure angle, involute spline Output shaft 14T 12/24 DP external involute spline C SAE B, 13T, 16/32 DP, 3 pressure angle, involute spline D SAE B-B, 15T, 16/32 DP, 3 pressure angle, involute spline E SAE C, 14T, 12/24 DP, 3 pressure angle, involute spline F SAE C-C, 17T, 12/24 DP, 3 pressure angle, involute spline G For ISO 8-A2HW pad with a 9T SAE spline H For ISO 8-A2HW pad with a 11T SAE spline J For ISO 1-A2/B4HW pad with a 13T SAE spline K For ISO 1-A2/B4HW pad with a 15T SAE spline L For ISO 125-A2/B4HW pad with a 14T SAE spline M For ISO 125-A2/B4HW pad with a 17T SAE spline 14, (.55) B Adapter Flange 372,1 (14.65) R2-2 places 35, (1.38) 4 places R3 4 places R4 (4 plcs) 359,6 (14.16) R1 92, (3.62) 4 places Right Hand Rotation with SAE 2-/4-Bolt B Flange and ISO 1 Adapter Flange Model Code Position 25 R1 Thru-drive Flange R2 2-bolt Thread R3 4-bolt Thread R4 Support Mounting Points C,D SAE J744-11-2 & -4.5-13 UNC-2B.5-13 UNC-2B.5-13 UNC-2B Ø11,675/11.625 bore 12,5/11,5 deep.98 deep.98 deep.98 deep J,K ISO 319/2-1A2 & B2 M12 M12 M12 Ø1,75/1.25 bore 12,5/11,5 deep 25, deep 25, deep 25, deep 18 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Thru-drive Models PVM131/141 Dimensions in millimeters (inches) C Adapter Flange 359,6 (14.16) S1 92, (3.62) 4 places S4 4 places 35, (1.38) 4 places 372,1 (14.65) S2 2 places S3 4 places Left Hand Rotation with SAE 2-/4-bolt C and ISO 125 Adapter Flange Model Code Position 25 S1 Thru-drive Flange S2 2-bolt Thread S3 4-bolt Thread R4 Support Mounting Points E,F SAE J744-127-2 & -4.625-11 UNC-2B.5-13 UNC-2B.5-13 UNC-2B Ø127,75/127.25 bore 15,5/14,5 deep.98 deep.98 deep.98 deep L,M ISO 319/2-125A2 & B4 M16 M12 M12 Ø125,75/125.25 bore 15,5/14,5 deep 25, deep 25, deep 25, deep Port B * B2 C * C2 F2 F3 SAE 2.5 inch dia. SAE J518 Code 61, low pressure.5-13 UNC-2B thd. 1.19 deep minimum 1.25 inch dia. SAE J518 Code 62, high pressure.5-13 UNC-2B thd. 1. deep minimum 146,8 (5.78) 114,9 (4.52) ISO 64mm diameter. ISO 6162 Type II, 315 M12 thread 31, deep minimum 32mm diameter. ISO 6162, 4 M12 thread 27, deep minimum 148,5 (5.85) 116,6 (4.59) *4-bolt flange port. See page 11 for load sensing, drain, and gage port threads. EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 19
Mounting Flange Options Dimensions in millimeters (inches) H 2-bolt A, B & C Flange ISO & SAE E F 2-bolt B Flange 4-bolt C or D Flange ISO & SAE L G L K K G A H A 45 J pilot J pilot 2-bolt or 4-bolt Series Flange Code Flange Description A E F G H J K L PVM18 2-bolt A SAE J744-82-2 Ø11,14 53,2 16,4 Ø82,53 +.2 -.3 PVM2 A (4.38) (2.9) (4.19) (Ø3.249) +. -.1 PVM18 2-bolt B ISO 319/2-8A2HW Ø11,14 54,5 19, Ø79,98 +.2 -.3 PVM2 A (4.38) (2.15) (4.29) (Ø3.15) +. -.1 PVM18 PVM2 PVM45 2-bolt C SAE J744-11-2 14,36 73, 146, Ø11,58+.2 PVM5 B -.3 PVM57 (.565) (2.87) (5.75) (Ø3.999) ±.1 PVM63 PVM18 PVM2 PVM45 2-bolt D ISO 319/2-1A2HW 14,14 7, 14, Ø1,/99,95 PVM5 B (special) (.557) (2.76) (5.51) (Ø3.937/3.935) PVM57 PVM63 E SAE J744-127-2 ( C ) 17,4 9,5 181, Ø127,/126,95 PVM57 PVM63 2-bolt (.685) (3.562) (7.125) (Ø5./4.998) PVM74 C F ISO 319/2-125A2HW 18, 9, 18, Ø125,/124,95 PVM81 (.79) (3.543) (7.9) (Ø4.921/4.919) PVM98 G SAE J744-127-4 ( C ) 14,2 57,25 114,5 Ø127,/126,95 PVM16 4-bolt (.559) (2.254) (4.58) (Ø5./4.998) PVM131 C PVM141 H ISO 319/2-125B4HW 14, Ø125,/124,95 8, 16, (.551) (Ø4.921/4.919) (3.15) (6.299) PVM131 4-bolt J SAE J744-152-4 ( D ) 2,6 8,82 161,64 Ø152,4/152,35 (.812) (3.182) (6.364) (Ø6./5.998) PVM141 D K ISO 319/2-16B4HW 18, Ø16,/159,95 1, 2, (.79) (Ø6.299/6.297) (3.937) (7.874) *Flanges for PVM2 and PVM5 are shown on pages 73 and 8, respectively. 11 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Shaft Options Dimensions in millimeters (inches) SAE Splined Shaft B spline C A D SAE Spline Shaft Max. Torque Model Series Designation Shaft Code A max. B C D Nm (lb. in.) SAE J744-16-4 SAE A (9T) 3 15,88 (.625) 9T 16/32 DP 37, (1.46) 32, (1.26) 58 (517) PVM18/2 SAE J744-19-4 SAE A (11T) 4 19,5 (.75) 11T 16/32 DP 3, (1.18) 38, (1.5) 123 (11) SAE J744-22-4 SAE B (13T) 7 21,81 (.859) 13T 16/32 DP 33, (1.31) 41, (1.61) 28 (185) SAE J744-25-4 SAE B-B (15T) 8 24,98 (.983) 15T 16/32 DP 38, (1.5) 46, (1.81) 337 (2987) PVM45/5 SAE J744-22-4 SAE B (13T) 7 21,81 (.859) 13T 16/32 DP 33, (1.31) 41, (1.61) 28 (185) SAE J744-25-4 SAE B-B (15T) 8 24,98 (.983) 15T 16/32 DP 38, (1.5) 46, (1.81) 337 (2987) SAE J744-22-4 SAE B (13T) 7 21,81 (.859) 13T 16/32 DP 33, (1.31) 41, (1.61) 28 (185) PVM57/63 SAE J744-25-4 SAE B-B (15T) 8 24,98 (.983) 15T 16/32 DP 38, (1.5) 46, (1.81) 337 (2987) SAE J744-32-4 SAE C (14T) 11 31,22 (1.23) 14T 12/24 DP 48, (1.89) 56, (2.2) 64 (566) SAE J744-32-4 PVM74/81 SAE C (14T) 11 31,22 (1.23) 14T 12/24 DP 48, (1.89) 56, (2.2) 64 (566) PVM98/16 SAE J744-38-4 SAE C-C (17T) 12 37,57 (1.479) 17T 12/24 DP 54, (2.13) 62, (2.44) 1215 (1,75) SAE J744-32-4 SAE C (14T) 11 31,22 (1.23) 14T 12/24 DP 48, (1.89) 56, (2.2) 64 (566) PVM131/141 SAE J744-38-4 SAE C-C (17T) 12 37,57 (1.479) 17T 12/24 DP 54, (2.13) 62, (2.44) 1215 (1,75) SAE J744-44-4 SAE D (13T) 14 43,71 (1.721) 13T 8/16 DP 67, (2.63) 75, (2.95) 1215 (1,75) EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 111
Shaft Options Dimensions in millimeters (inches) SAE Keyed Shaft E key C B A D Max. SAE Keyed Shaft Shaft Torque Model Series Designation Code A B C D E Nm (lb. in.) SAE J744-16-1 SAE A 1 15,88 (.625) 17,73 (.698) 24, (.94) 32, (1.26) 4, (.157) 58 (517) PVM18/2 SAE J744-19-1 SAE 19-1 2 19,5 (.75) 21,23 (.836) 24, (.94) 32, (1.26) 4,81 (.189) 14 (918) SAE J744-22-1 SAE B 5 22,22 (.875) 25,12 (.989) 33, (1.31) 41, (1.61) 6,35 (.25) 135 (12) SAE J744-25-1 SAE B-B 6 25,37 (.999) 28,22 (1.111) 38, (1.5) 46, (1.81) 6,35 (.25) 215 (19) PVM45/5 SAE J744-22-1 SAE B 5 22,22 (.875) 25,12 (.989) 33, (1.31) 41, (1.61) 6,35 (.25) 135 (12) SAE J744-25-1 SAE B-B 6 25,37 (.999) 28,22 (1.111) 38, (1.5) 46, (1.81) 6,35 (.25) 215 (19) PVM57/63 SAE J744-25-1 SAE B-B 6 25,37 (.999) 28,22 (1.111) 38, (1.5) 46, (1.81) 6,35 (.25) 215 (19) SAE J744-32-1 SAE C 9 31,75 (1.25) 35,32 (1.39) 48, (1.89) 56, (2.2) 7,93 (.312) 45 (398) SAE J744-32-1 9 31,75 (1.25) 35,32 (1.39)48, (1.89) 56, (2.2) 7,93 (.312) 45 PVM74/81 SAE C (398) PVM98/16 SAE J744-38-1 SAE C-C 1 38,1 (1.5) 42,39 (1.67) 54, (2.13) 62, (2.44) 9,52 (.375) 765 (677) SAE J744-32-1 SAE C 9 31,75 (1.25) 35,32 (1.39)48, (1.89) 56, (2.2) 7,93 (.312) 45 (398) PVM131/141 SAE J744-38-1 SAE C-C 1 38,1 (1.5) 42,39 (1.67) 54, (2.13) 62, (2.44) 9,52 (.375) 765 (677) SAE J744-44-1 SAE D 13 44,45 (1.75) 49,46 (1.95) 67, (2.63) 75, (2.95) 11,11 (.438) 12 (1,62) 112 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Shaft Options Dimensions in millimeters (inches) D key ISO Keyed Shaft E A C B Max. ISO Keyed Shaft Shaft Torque Model Series Designation Code A B C D E Nm (lb. in.) ISO 319/2 E2N 15 19,9 (.786) 8,5 (.335) 36 (1.42) 6 (.236) 22,5 (.886) 113 (1) PVM18/2 ISO 319/2 E25N Short Spigot 16 25 (.984) 8,5 (.335) 42 (1.65) 8 (.315) 28, (1.12) 215 (19) ISO 319/2 E25N 17 25 (.984) 1 (.393) 42 (1.65) 8 (.315) 28, (1.12) 215 (19) PVM45/5 ISO 319/2 E25N 17 25 (.984) 1 (.393) 42 (1.65) 8 (.315) 28, (1.12) 215 (19) PVM57/63 ISO 319/2 E25N 17 25 (.984) 1 (.393) 42 (1.65) 8 (.315) 28, (1.12) 215 (19) ISO 319/2 E32N 18 32 (1.26) 1 (.393) 58 (2.28) 1 (.394) 35, (1.378) 45 (398) PVM74/81 ISO 319/2 E32N 18 32 (1.26) 1,5 (.413) 58 (2.28) 1 (.394) 35, (1.378) 45 (398) PVM98/16 ISO 319/2 E4N 19 4 (1.57) 1,5 (.413) 82 (3.23) 12 (.472) 43, (1.693) 87 (77) PVM131/141 ISO 319/2 E32N 18 32 (1.26) 1 (.393) 58 (2.28) 1 (.394) 35, (1.378) 45 (398) ISO 319/2 E4N 19 4 (1.57) 1 (.393) 82 (3.23) 12 (.472) 43, (1.693) 87 (77) (1)ISO 8mm pilot only B (2)ISO 8mm pilot only D *Torque of non-thru-drive PVM pump, or combined torque of PVM thru-drive pump and thru-driven pump. NOTE: In those cases where geometric tolerances of mounting are critical, or where specific tolerance ranges are required and not specified, consult Eaton Engineering for specific limits. EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 113
Shaft Selection Data SAE Splined Shafts Max. Torque Max. Thru-drive Output Torque Model Series Shaft Designation Shaft Code Nm (lb. in.) Nm (lb. in.) SAE J744-16-4 (SAE A, 9T) 3 58 (513) Exceeds maximum input torque PVM18/2 SAE J744-19-4 (SAE A, 11T) 4 123 (11) Exceeds maximum input torque SAE J744-22-4 (SAE B, 13T) 7 28 (185) 123 (11) SAE J744-25-4 (SAE B-B, 15T) 8 337 (2987) 123 (11) PVM45/5 SAE J744-22-4 (SAE B, 13T) 7 28 (185) 28 (185)* SAE J744-25-4 (SAE B-B, 15T) 8 337 (2987) 337 (2987) SAE J744-22-4 (SAE B, 13T) 7 28 (185) 28 (185)* PVM57/63 SAE J744-25-4 (SAE B-B, 15T) 8 337 (2987) 337 (2987) SAE J744-32-4 (SAE C, 14T) 11 64 (566) 337 (2987) PVM74/81 SAE J744-32-4 (SAE C, 14T) 11 64 (566) 515 (456) PVM98/16 SAE J744-38-4 (SAE C-C, 17T) 12 1215 (1,75) 515 (456) SAE J744-32-4 (SAE C, 14T) 11 64 (566) 64 (566) PVM131/141 SAE J744-38-4 (SAE C-C, 17T) 12 1215 (1,75) 64 (566) SAE J744-44-4 (SAE D, 13T) 14 1215 (1,75) 64 (566) SAE Keyed Shafts Max. Torque Max. Thru-drive Output Torque Model Series Shaft Designation Shaft Code Nm (lb. in.) Nm (lb. in.) SAE J744-16-1 (SAE A ) 1 58 (513) Exceeds maximum input torque PVM18/2 SAE J744-19-1 (SAE 19-1 ) 2 14 (92) Exceeds maximum input torque SAE J744-22-1 (SAE B ) 5 135 (12) 123 (11) SAE J744-25-1 (SAE B-B ) 6 215 (19) 123 (11) PVM45/5 SAE J744-22-1 (SAE B ) 5 135 (12) 135 (12)* SAE J744-25-1 (SAE B-B ) 6 215 (19) 215 (19)* PVM57/63 SAE J744-25-1 (SAE B-B ) 6 215 (19) 215 (19)* SAE J744-32-1 (SAE C ) 9 45 (398) 337 (2987) PVM74/81 SAE J744-32-1 (SAE C ) 9 45 (398) 45 (398)* PVM98/16 SAE J744-38-1 (SAE C-C ) 1 765 (677) 515 (456) SAE J744-32-1 (SAE C ) 9 45 (398) 45 (398)* PVM131/141 SAE J744-38-1 (SAE C-C ) 1 765 (677) 64 (566) SAE J744-44-1 (SAE D ) 13 12 (1,62) 64 (566) ISO Keyed Shafts Max. Torque Max. Thru-drive Output Torque Model Series Shaft Designation Shaft Code Nm (lb. in.) Nm (lb. in.) ISO 319/2 E2N (B mount only) 15 113 (1) Exceeds maximum input torque PVM18/2 ISO 319/2 E25N (B mount only) 16 215 (19) Exceeds maximum input torque ISO 319/2 E25N (D mount only) 17 215 (19) 123 (11) PVM45/5 ISO 319/2 E25N 17 215 (19) 215 (19)* PVM57/63 ISO 319/2 E25N 17 215 (19) 215 (19)* ISO 319/2 E32N 18 45 (398) 337 (2987) PVM74/81 ISO 319/2 E32N 18 45 (398) 45 (398)* PVM98/16 ISO 319/2 E4N 19 87 (77) 515 (456) PVM131/141 ISO 319/2 E32N 18 45 (398) 45 (398)* ISO 319/2 E4N 19 87 (77) 64 (566) Maximum total torque of the thru-drive pump and the thru-driven pump(s). Maximum torque that can be applied to the thru-driven pump(s). *This value is limited by the maximum input torque. 114 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Port Options Inlet and Outlet Ports Inlet/Outlet Port Option Port Model Series (per model code, page 5) Code Inlet Port B Outlet Port C Inch Flange 2 SAE J518 Code 61, standard pressure. SAE J518 Code 61, standard pressure. 1.25 inch diameter,.4375-14 x 1.12 bolt holes.75 inches diameter,.375-16 x.88 bolt holes PVM18/2 Metric Flange 4 ISO 6162 Type II, 315. 31,75mm diameter, M1 x 28 bolt holes ISO 6162 Type II, 315. 19,5mm diameter, M1 x 22 bolt holes Inch Tube 1 SAE J514 O-ring 2, for 1-1/4 inch O.D. tube SAE J514 O-ring -12, for 3/4 inch O.D. tube Metric Tube 3 ISO 6149-1, M42 thread ISO 6149-1, M27 thread British Parallel Pipe 5 ISO 228-1:1994 (E), G 1-1/4 thread ISO 228-1:1994 (E), G 3/4 thread Inch Flange 2 SAE J518 Code 61, standard pressure. 2. inch diameter,.5-13 x 1.6 bolt holes SAE J518 Code 61, standard pressure. 1. inch diameter,.375-16 x.87 bolt holes PVM45/5 Metric Flange 4 ISO 6162 Type II, 315. 51mm diameter, M12 x 27 bolt holes ISO 6162 Type II, 315. 25mm diameter, M1 x 22 bolt holes Inch Tube 1 SAE J514 O-ring -24, for 1-1/2 inch O.D. tube SAE J514 O-ring -16, for 1 inch O.D. tube Metric Tube 3 ISO 6149-1, M48 thread ISO 6149-1, M33 thread British Parallel Pipe 5 ISO 228-1:1994 (E), G 1-1/2 thread ISO 228-1:1994 (E), G1 thread Inch Flange 2 SAE J518 Code 61, standard pressure. 2. inch diameter,.5-13 x 1.6 bolt holes SAE J518 Code 61, standard pressure. 1. inch diameter,.375-16 x.88 bolt holes PVM57/63 Metric Flange 4 ISO 6162 Type II, 35. ISO 6162 Type, 35. 51mm diameter, M12 x 29 bolt holes 25mm diameter, M1 x 23 bolt holes Inch Tube 1 SAE J514 O-ring -24, SAE J514 O-ring (End ported models only) for 1-1/2 inch O.D. tube -16 for 1 inch O.D. tube Metric Tube (End ported models only) 3 ISO 6149-1, M48 thread ISO 6149 1, M33 thread PVM74/81 Inch Flange 2 SAE J518 Code 61, standard pressure. 2. inch diameter,.5-13 x 1.19 bolt holes SAE J518 Code 61, standard pressure. 1. inch diameter,.375-16 x.88 bolt holes Metric Flange 4 ISO 6162 Type II, 315. 51mm diameter, M12 x 2 bolt holes ISO 6162 Type, 4. 25mm diameter, M1 x 17 bolt holes PVM98/16 Inch Flange 2 SAE J518 Code 61, standard pressure. 2.5 inch diameter,.5-13 x 1.19 bolt holes SAE J518 Code 61, standard pressure. 1. inch diameter,.375-16 x.88 bolt holes Metric Flange 4 ISO 6162 Type I, 35. 64mm diameter, M12 x 31 bolt holes ISO 6162 Type I, 35. 25mm diameter, M1 x 23 bolt holes PVM131/141 Inch Flange 2 SAE J518 Code 61, standard pressure. 2.5 inch diameter,.5-13 x 1.19 bolt holes SAE J518 Code 62, high pressure. 1.25 inch diameter,.5-13 x 1. bolt holes Metric Flange 4 ISO 6162 Type II, 315. 64mm diameter, M12 x 31 bolt holes ISO 6162 Type, 4. 32mm diameter, M12 x 27 bolt holes Drain, Load Sensing, and Gauge Ports Inlet/Outlet Port Option Port Model Series (per model code, page 5) Code Drain Port F Load Sensing Port J Gauge Port K Inch Flange or Tube 1, 3 SAE J514 O-ring,.5 O.D. SAE J514 O-ring,.25 O.D. SAE J514 O-ring,.25 tube. tube..75-16 UNF 2B thread tube..4375-2 UNF 2B thread.4375-2 UNF 2B thread PVM18/2 Metric Flange or Tube 3, 4 ISO 6149-1 O-ring M18 x 1,5 thread ISO 6149-1 O-ring M12 x 1,5 thread ISO 6149-1 O-ring M12 x 1,5 thread British Parallel Pipe 5 ISO 228-1:1994 (E) ISO 228-1:1994 (E) ISO 228-1:1994 (E) G 1/2 thread G 1/4 thread G 1/4 thread Inch Flange or Tube 1, 3 SAE J514 O-ring,.625 O.D. SAE J514 O-ring,.25 O.D. SAE J514 O-ring,.375 O.D. tube. tube..875-14 UNF 2B thread tube..4375-2 UNF 2B thread.5625-18 UNF 2B thread PVM45/5 Metric Flange or Tube 3, 4 ISO 6149-1 O-ring M22 x 1,5 thread ISO 6149-1 O-ring M12 x 1,5 thread ISO 6149-1 O-ring M14 x 1,5 thread British Parallel Pipe 5 ISO 228-1:1994 (E) ISO 228-1:1994 (E) ISO 228-1:1994 (E) G 1/2 thread G 1/4 thread G 1/4 thread Inch Flange or Tube 1, 2 SAE J514 O-ring,.625 O.D. SAE J514 O-ring,.375 O.D. SAE J514 O-ring,.375 O.D. tube. PVM57/63 tube..875-14 UNF 2B thread tube..5625-18 UNF 2B thread.5625-18 UNF 2B thread Metric Flange or Tube 3, 4 ISO 6149-1 O-ring ISO 6149-1 O-ring ISO 6149-1 O-ring M22 x 1,5 thread M14 x 1,5 thread M14 x 1,5 thread Inch Flange 2 SAE J514 O-ring,.625 O.D. SAE J514 O-ring,.375 O.D. SAE J514 O-ring,.375 O.D. tube. PVM74/83 tube..875-14 UNF 2B thread tube..562-18 UNF 2B thread.5625-18 UNF 2B thread PVM98/16 Metric Flange 4 ISO 6149-1 O-ring ISO 6149-1 O-ring ISO 6149-1 O-ring M22 x 1,5 thread M14 x 1,5 thread M14 x 1,5 thread Inch Flange 2 SAE J514 O-ring,.625 O.D. SAE J514 O-ring,.375 O.D. SAE J514 O-ring,.375 O.D. tube. PVM131/141 tube..875-14 UNF 2B thread tube..562-18 UNF 2B thread.5625-18 UNF 2B thread Metric Flange 4 ISO 6149-1 O-ring ISO 6149-1 O-ring ISO 6149-1 O-ring M22 x 1,5 thread M14 x 1,5 thread M14 x 1,5 thread EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 115
Operating Requirements Inlet Pressure, Case Pressure, and Operating Temperature Requirements Inlet Pressure Case Pressure Operating Temperature Rated Minimum Maximum Maximum Maximum Maximum Absolute, absolute Gauge Continuous Intermittent Peak Rated Intermittent ( (in. Hg) ( ( ( ( C ( F) C ( F) 1, (14.5),85 (5) 3,5 (5),5 (7) 2 (3) 3,5 (5) 82 (18) 14 (22) Hydraulic Fluids Minimum Viscosity @ Max. Recommended Operating Maximum Viscosity Intermittent Temperature of Viscosity Range at Startup 14 C (22 F) Fluid cst (SUS) cst (SUS) cst (SUS) Use antiwear hydraulic oil, or automotive type crankcase oil (designations SC, SD, SE, 16 to 4 (83 to 187) 1 (455) 1 (9) or SF) per SAE J183 FEB8 For more information, see Eaton publication 579. For operation on other alternative or environmentally friendly fluids, please contact your Eaton Representative. Fluid Cleanliness The M Series pumps are rated in anti-wear petroleum fluids with a contamination level of 2/18/13 (Eaton) or ISO 18/13. Operation in fluids with levels more contaminated than this is not recommended. Fluids other than petroleum, severe service cycles, or temperature extremes are cause for adjustment of these codes. Please contact your Eaton Representative for specific duty cycle recom mendation. Eaton M Series pumps, as with any variable displacement piston pumps, will operate with apparent satisfaction in fluids up to the rating specified here. Experience has shown, however, that pump and hydraulic system life is not optimized with high fluid contamination levels (high ISO cleanliness codes). Proper fluid condition is essential for long and satisfac tory life of hydraulic components and systems. Hydraulic fluid must have the correct balance of cleanliness, materials, and additives for protection against wear of components, elevated viscosity and inclusion of air. Essential information on the correct methods for treating hydraulic fluid is included in Eaton publication 561 Eaton Guide to Systemic Contamination Control Available from your local Eaton distributor. In this publication, filtration and cleanliness levels for extending the life of axial piston pumps and other system components are listed. Included is an excellent discussion of the selection of products needed to control fluid condition. Moment of Inertia (single pump rotating group) Model Moment of Inertia N-m (sec 2 ) lbf-in (sec 2 ) PVM18.12.14 PVM2.12.14 PVM45.36.32 PVM5.34.3 PVM57.52.457 PVM63.51.447 PVM74.78.691 PVM81.73.643 PVM98.132.1165 PVM16.123.186 PVM131.213.1889 PVM141.21.1856 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215 116
Specifications and Performance Quiet version, optimized for 1-18 rpm (E) and Higher speed version (M) Alternate fluids guide Specifications and Performance Fluid Type / Model Series Petroleum Base Petroleum Base ZDDP Zinc Free Tractor Motor Oil Universal Automatic Mil Spec Fluids Transmission Fluid Environmentally Acceptable Fluids AW (HM) AW (HM) UTTO ATF HETG HEES Fire Resistant Fluids Vegetable Base Synthetic Base Synthetic Base Water Containing Phosphate ester HFDR Polyester - HFDU Polyether polyol - HFDU Water Glycol - HFC Invert Emulsion - HFB Specialty Fluids Food Grade Fluid Cutting Fluids H1 - approved Model series Quiet version E @ 18 Unless Noted 1 PVM 18, PVM 45, PVM 57, PVM 74, PVM 98 46 PSI NR 3625 PSI ** 3625 PSI ** 3625 PSI ** NR 3625 PSI ** 3625 PSI 18 33 PSI ** 33 PSI ** NR 25 PSI ** 225 PSI ** NR 3625 PSI ** PVM 2, PVM 5, PVM 63, PVM 81, PVM 16 3335 PSI NR 325 PSI ** 325 PSI ** 325 PSI ** NR 325 PSI ** 325 PSI 18 3 PSI ** 3 PSI ** NR 225 PSI ** 2 PSI ** NR 325 PSI ** PVM 131 46 PSI NR 3625 PSI ** 3625 PSI ** 3625 PSI ** NR 3625 PSI ** 3625 PSI 15 33 PSI ** 15 rpm 33PSI ** 15 rpm NR 25 PSI ** 15 rpm 225 PSI ** 15 rpm NR 3625 PSI ** PVM 141 3335 PSI NR 325 PSI ** 325 PSI ** 325 PSI ** NR 325 PSI ** 325 PSI 15 3 PSI ** 15 rpm 3 PSI ** 15 rpm NR 225 PSI ** 15 rpm 2 PSI ** 15 rpm NR 325 PSI ** Model Series Higher Speed Version (M) 2 PVM 18 46 PSI 28 NR 3625 PSI ** 28 3625 PSI ** 28 3625 PSI ** 28 NR 3625 PSI ** 28 3625 PSI 18 33 PSI ** 18 33 PSI ** 18 NR 25 PSI ** 18 225 PSI ** 18 NR NR PVM 2 3335 PSI 28 NR 325 PSI ** 28 325 PSI ** 28 325 PSI ** 28 NR 325 PSI ** 28 325 PSI 18 3 PSI ** 18 3 PSI ** 18 NR 225 PSI ** 18 2 PSI ** 18 NR NR PVM 45 46 PSI 26 NR 3625 PSI ** 26 3625 PSI ** 26 3625 PSI ** 26 NR 3625 PSI ** 26 3625 PSI 18 33 PSI ** 18 33 PSI ** 18 NR 25 PSI ** 18 225 PSI ** 18 NR NR PVM 5 3335 PSI 26 NR 325 PSI ** 26 325 PSI ** 26 325 PSI ** 26 NR 325 PSI ** 26 325 PSI 18 3 PSI ** 18 3 PSI ** 18 NR 225 PSI ** 18 2 PSI ** 18 NR NR PVM 57 46 PSI 25 NR 3625 PSI ** 25 3625 PSI ** 25 3625 PSI ** 25 NR 3625 PSI ** 25 3625 PSI 18 33 PSI 18 33 PSI 18 NR 25 PSI ** 18 225 PSI ** 18 NR NR PVM 63 3335 PSI 25 NR 325 PSI ** 25 325 PSI ** 25 325 PSI ** 25 NR 325 PSI ** 25 325 PSI 18 3 PSI ** 18 3 PSI ** 18 NR 225 PSI ** 18 2 PSI ** 18 NR NR PVM 74 46 PSI 24 NR 3625 PSI ** 24 3625 PSI ** 24 3625 PSI ** 24 NR 3625 PSI ** 24 3625 PSI 18 33 PSI ** 18 33 PSI ** 18 NR 25 PSI ** 18 225 PSI ** 18 NR NR PVM 81 3335 PSI 24 NR 325 PSI ** 24 325 PSI ** 24 325 PSI ** 24 NR 325 PSI ** 24 325 PSI 18 3 PSI ** 18 3 PSI ** 18 NR 225 PSI ** 18 2 PSI ** 18 NR NR PVM 98 46 PSI 22 NR 3625 PSI ** 22 3625 PSI ** 22 3625 PSI ** 22 NR 3625 PSI ** 22 3625 PSI 18 33 PSI ** 18 33 PSI ** 18 NR 25 PSI ** 18 225 PSI ** 18 NR NR PVM 16 3335 PSI 22 NR 325 PSI ** 22 325 PSI ** 22 325 PSI ** 22 NR 325 PSI ** 22 325 PSI 18 3 PSI ** 18 3 PSI ** 18 NR (PSI) 18 225 PSI ** 18 2 PSI ** NR NR PVM 131 46 PSI 2 NR 3625 PSI ** 2 3625 PSI ** 2 3625 PSI ** 2 NR 3625 PSI ** 2 3625 PSI 15 33 PSI ** 18 33 PSI ** 18 NR 25 PSI ** 15 225 PSI 15 NR NR PVM 141 3335 PSI 2 NR 325 PSI ** 2 325 PSI ** 2 325 PSI ** 2 NR 325 PSI ** 2 325 PSI 15 3 PSI ** 18 3 PSI** 18 NR 225 PSI ** 15 2 PSI ** 15 NR NR 117 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Installation and Start-up Warning: Care should be taken that mechanical and hydraulic resonances are avoided in the application of the pump. Such resonances can seriously compromise the life and/or safe operation of the pump. Drive Data Mounting attitude can be either horizontal or vertical, using the appropriate case drain ports to ensure that the case remains full of fluid at all times. Consult your local Eaton Representative if a different arrangement is required. In those cases where geometric tolerances of mounting are critical, or where specific tolerance ranges are required and not specified, consult Eaton Engineering for specific limits. Direction of shaft rotation, viewed from the prime mover end, must be as indicated in the model designation on the pump either right hand (clockwise) or left hand (counterclockwise). Direct coaxial drive through a flexible coupling is recommended. If drives imposing radial shaft loads are considered, please consult your Eaton Representative. Start-up Procedure Make sure the reservoir and circuit are clean and free of dirt/debris prior to filling with hydraulic fluid. Fill the reservoir with filtered oil and fill to a level sufficient enough to prevent vortexing at the suction connection to pump inlet. It is good practice to clean the system by flushing and filtering, using an external slave pump. Caution: Before the pump is started, fill the case through the uppermost drain port with hydraulic fluid of the type to be used. The case drain line must be connected directly to the reservoir and must terminate below the oil level. Once the pump is started, it should prime within a few seconds. If the pump does not prime, check to make sure that there are no restrictions between the reservoir and the inlet to the pump, that the pump is being rotated in the proper direction, and that there are no air leaks in the inlet line and connections. Also check to make sure that trapped air can escape at the pump outlet. After the pump is primed, tighten the loose outlet connections, then operate for five to ten minutes (unloaded) to remove all trapped air from the circuit. If the reservoir has a sight gage, make sure the fluid is clear not milky. 118 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Operation and Installation Power Control/Torque Limiter Description PVM series piston pump with Power Control consists of, A) pump with modified pressure and flow compensator and B) Power Control subassembly installed. Pump with PFC Power control S/A Power Control Operation The Power Control Subassembly consists of a poppet type valve guided by a specially designed control piston having a unique profile. The cracking pressure of the poppet valve, being guided by the profile on the control piston, is dependent on the actual displacement of the pump. For lower displacement the cracking pressure is high. As displacement is increased, the cracking pressure is reduced according to the profile on the control piston. The poppet type valve gets pressure signal either from the modified load sense port (for Pressure Flow Compensated) or the pump outlet pressure (for Pressure Compensated). The power control subassembly regulates this pressure based on the displacement. This regulated pressure is internally fed back to the control piston chamber, which compensates by adjusting the pump displacement appropriately. This results in achieving the desired control of constant nput power. Adjusting screw Lock nut Power Control Adjustment To adjust the control power setting, power measurement devices are required. For power, motor torque and speed need to be measured. For output power, devices for pump pressure and flow measurements are required. The pump comes with factory set power setting as indicated by pos. 22 23 of pump model code. It is recommended not to change this setting unless absolutely necessary. The setting can be changed by loosening the lock nut on top of the control subassembly and turning the adjust ment screw with help of allen key. Rotating adjustment screw clockwise increases the power setting while rotating it anticlockwise reduces it. After adjustment as required ensure that the locknut is tightened properly. 119 EATON Industrial Variable Displacement Piston Pumps V-PUPI-TM7-E2 April 215
Eaton Hydraulics Group USA 14615 Lone Oak Road Eden Prairie, MN 55344 USA Tel: 952-937-98 Fax: 952-294-7722 www.eaton.com/hydraulics Eaton Hydraulics Group Europe Route de la Longeraie 7 111 Morges Switzerland Tel: +41 () 21 811 46 Fax: +41 () 21 811 461 Eaton Hydraulics Group Asia Pacific Eaton Building No.7 Lane 28 Linhong Road Changning District, Shanghai 2335 China Tel: (+86 21) 52 99 Fax: (+86 21) 223 724 215 Eaton All Rights Reserved Printed in USA Document No. V-PUPI-TM7-E2 April 215