3G-SDI/HD-SDI/SD-SDI Electric to Optical Converter EO3G-200 1. Abstract Electric to Optical Converter for 3G-SDI / HD-SDI / SD-SDI digital video signal Recommended to install in CANARE 161UPSC / 6PSC converter platform Features Cable equalizer and re-clocker equipped A monitor out terminal equipped Capable of receiving and transmitting pathological test pattern(smpte PR-178,198 Check Field Test Pattern) Capable of receiving 3G-SDI signal through CANARE L-5CFB cable of longer than 100m. Supports multi-rate, multi-format(3g-dsi / HD-SDI / SD-SDI / DVB-ASI) Small size (2 slot size for 161UPSC) Low power consumption Application Optical transmission for inside use in broadcasting station. Optical transmission for inter-station use Dark fiber use Standards SMPTE 259M,292M,297-2006,424M BTA S-004C EN50083-9 Certifications FDA21 CFR Part1040.10,11 with LN50, Class 1 IEC 60825-1:2007 FCC Part15 Class A UL / c-ul CB scheme CE marking Operating Environment RoHS compliant 1/7
2. Diagram 5V DC-DC Converter 75 Ohm Cable Equalizer Re- Clocker Laser Driver 75 Ohm Cable Driver 3. Specifications 3-1. Absolute ratings Items Ratings Storage temperature -40 C ~ 85 C Supply voltage(din 2pin & 10pin) -0.3V ~ 6.5V 3-2. Recommended operating conditions Items Operating conditions Supply voltage(din 2pin & 10pin) 5 V±0.25V Temperature 0 C ~ 40 C Humidity 30% ~ 85% (without condensation) 3-3. Transmission signals, bit rates Transmission signals 3G-SDI HD-SDI SD-SDI/DVB-ASI Bit rates 2.97Gbps 2.97/1.001Gbps 1.485Gbps 1.485/1.001Gbps 270Mbps 3-4. Optical specifications Optical interface Number of output ports 1 Optical connector LC Fiber SM10/125 Laser device FP laser (1310nm) 2/7
Optical performance (Under recommended operating condition) Items Min. Typ. Max. Unit Central wavelength 1280 1310 1340 Wave width 3 nm Optical output power -7.0-5.0-3.0 dbm Extinction ratio 7.0 9.5 db Rise time/ Fall time 135 Jitter 100 ps Caution Do not watch laser beam directly whenever this product works. Even if the beam is from optical connector, your eyes may be damaged. Laser safety This product equips Class 1 laser products, which complies with FDA 21 CFR 1040.10,11 with LN50, Class 1. EO3G-200 3-5. Electric specifications Electric interface Number of input ports 1 Input impedance 75Ω Input Connector Number of output ports 1 Output impedance 75Ω Output Connector Electric performance (Under recommended operating condition) Items Min. Typ. Max. Unit Minimum transmission bit rate 125 Mbps Current consumption 300 400 ma Input signal level (0m Cable) 720 800 950 mvpp Return loss 5M ~1.5GHz 15 1.5G ~3.0GHz 10 db Monitor Out signal level (75Ω load) 720 800 880 mvpp Return loss 5MHz~1.5GHz 15 1.5GHz~3.0GHz 10 db Rise time /fall time SD-SDI 400 800 3G-SDI/HD-SDI 90 130 ps SD-SDI 0.2 Alignment jitter HD-SDI 0.2 3G-SDI 0.3 SD-SDI 0.2 UI Timing jitter HD-SDI 1.0 3G-SDI 2.0 Monitor output level High 4.2 5.0 (DIN connector) Low 0 0.4 V 3/7
3-6. LED indication LED name Indication Lock to 3G-SDI / HD-SDI :Green 3GHD/SD Lock to SD-SDI / DVB-ASI :Yellow Unlock :No lighting LD Laser on :Green Laser off :No lighting 3-7. Structure Size Weight Items Spec. 35.5mm(W) 43.4mm(H) 78mm(D) (Except protuberance such as connectors) Approx. 150 g 4. Appearance (Unit:mm) 4/7
5. Part name and function 1) Captive Screw To fix this product to the platform. 2) Connector For connection with 75Ω coaxial cable to monitor the input signal. 3) Connector For connection with 75Ω coaxial cable to input the signal. 4) LC Connector For connection with SM optical fiber. 5) Status LED(LD) Green light comes on when an optical signal is input. 6) Status LED(3GHD/SD) Green light comes on when 3G-SDI or HD-SDI signal is input. Yellow light comes on when SD-SDI or DVB-ASI with 270Mbps signal is input. 7) DIN Connector(16-pin) For the power supply and status signal outputs. 8) Connector Label Production No. described. 9) ID Label Describes the model name, rating, certifications, and so on 6. DIN Connector Pin assign Pin number Pin name Function 1,9 GND Electrical ground 2,10 5V DC5V power input 3 /LOCK Re-clocker Status output CMOS open drain (Pulled up to 5V with 100K ohm internally) Lock :Lo Unlock :Hi 6 DIS0 Plug in ID output 7 DIS1 DIS0:Lo, DIS1:Lo, DIS2:Lo 8 DIS2 11 /LD Laser status monitor output CMOS open drain ( Pulled up to 5V with 100K ohm internally ) Laser on :Lo Laser off :Hi 12 HD/SD Input signal ID output CMOS open drain ( Pulled up to 5V with 100K ohm internally ) SD : Lo 3G/HD: Hi 14 SS2 Bit rate information 15 SS1 SS2/SS1/SS0:all Lo 16 SS0 4,5,13 NC(Reserved) Not use 5/7
7. Typical operating characteristics 2.97Gbps 1.485Gbps 270Mbps L-5CFB:100m L-5CFB:200m L-5CFB:400m Optical eye pattern L-5CFB:100m L-5CFB:200m Optical power vs. error rate (Receiver: Canare reference OE3G-101) Frequency (GHz) 0 1.5 3.0 10 SMPTE Spec. Return loss (db) 20 30 40 SDI IN Return loss characteristics Monitor OUT Return loss characteristics 6/7
Electrical output wave form 8. Revision history May. 2013 :Rev.1.0 9. Contact point Japan 4th FL, WN Bldg., Shin-Yokohama, Kohoku-ku, Yokohama-shi, Kanagawa, 222-0033 Japan Phone : +81-45-470-5674 Fax : +81-45-470-5676 E-mail : overseas@canare.co.jp Web : www.canare.co.jp/oversea/mainmenu.html USA 45 Commerce Way, Unit C, Totowa, New Jersey, 07512 USA Phone : +1-973-837-0070 Fax : +1-973-837-0080 E-mail : sales@canare.com Web : www.canare.com Europe 14-30, rue de Mantes 92700 Colombes France Phone : +33(0)1 42 42 16 23 E-mail : info@canare.fr Web : www.canare.fr This document may be revised without advanced information. 7/7