ree XLamp XM-L LEDs PRODUT FMILY DT SHEET LD-DS33 REV 2 WWW.REE.OM/XLMP PRODUT DESRIPTION The XLamp XM-L LED is the industry s highest performance, singledie white lighting-class LED. XLamp XM-L is 20% more efficient than XLamp XP-G at the same current, and can deliver 1000 lumens with 100 lumens per Watt efficacy. The XLamp XM-L LED offers ree s industry-leading features: wide viewing angle, symmetrical package, unlimited floor life and electrically neutral thermal path. XLamp XM-L LEDs can enable LED light into new applications that require tens of thousands of lumens, such as high bay and high-output area lighting. XM-L is also the ideal choice for lighting applications where high light output and maximum efficacy are required, such as LED light bulbs, outdoor lighting, portable lighting, indoor lighting and solar-powered lighting. FETURES Maximum drive current: 3000 m Low thermal resistance: 2.5 /W Maximum junction temperature: 150 Viewing angle: 125 vailable in warm, neutral and cool white NSI-compatible chromaticity opyright 2010-2011 ree, Inc. ll rights reserved. The information in this document is subject to change without notice. opyright 2010 ree, Inc. ll rights reserved. The information in this document is subject to change without notice. ree, the ree logo and XLamp are registered trademarks of ree, Inc. ree, the ree logo and XLamp are registered trademarks of ree, Inc. bins Unlimited floor life at 30º/85% RH Reflow solderable - JEDE J-STD-020 Electrically neutral thermal path TLE OF ONTENTS Label Flux haracteristics... with ree in ode, 2 Qty, haracteristics... Lot #... 2 10 Label Relative with Spectral ustomer Power Order ode,... 10 Distribution... 3 Qty, Relative Reel ID, Flux PO# vs.... Junction 10 Temperature... 3 Electrical haracteristics... Thermal Design... Relative Flux vs. urrent... 5 Relative hromaticity vs. urrent and Temperature (ool White)... 5 Relative hromaticity vs. urrent and Temperature (Warm White)... 6 Typical Spatial Distribution... 7 Reflow Soldering haracteristics... 8 Notes... 9 Mechanical Dimensions...10 Tape and Reel... 9 Packaging...10 Label with ree in ode, Qty, Lot #... 10 Label with ustomer Order ode,... 10 Qty, Reel ID, PO#... 10 ree, Inc. 600 Silicon Drive Durham, N 27703 US Tel: +1.919.313.5300 www.cree.com/xlamp
XLMP XM-L LEDS FLUX HRTERISTIS (TJ = 25 ) The following table provides several base order codes for XLamp XM-L LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-code nomenclature, please consult the XLamp XM-L inning and Labeling document. olor T Range ase Order odes Min Luminous Flux @ 700 m (lm) Order ode Min. Max. Group Flux (lm) ool White 5,000 K 8,300 K Neutral White 3,700 K 5,000 K Warm White 2,600 K 3,700 K T5 260 XMLWT-00-0000-0000T5051 T6 280 XMLWT-00-0000-0000T6051 T 20 XMLWT-00-0000-000LT0E T5 260 XMLWT-00-0000-000LT50F T2 200 XMLWT-00-0000-000LT20E7 T3 220 XMLWT-00-0000-000LT30F7 Notes: ree maintains a tolerance of ± 7% on flux and power measurements and ± 2 on RI measurements. Typical RI for ool White (5,000 K 8,300 K T) is 65. Typical RI for Neutral White (3,700 K 5,000 K T) is 75. Typical RI for Warm White (2,600 K 3,700 K T) is 80. HRTERISTIS haracteristics Unit Minimum Typical Maximum Thermal Resistance, junction to solder point /W 2.5 Viewing ngle (FWHM) degrees 125 Temperature coefficient of voltage mv/ -3.0 ESD lassification (HM per Mil-Std-883D) lass 2 D Forward urrent m 3000 Reverse Voltage V 5 Forward voltage (@ 700 m) V 2.9 3.5 Forward voltage (@ 1500 m) V 3.1 Forward voltage (@ 3000 m) V 3.35 LED Junction Temperature 150 ree, of Inc. ree, of Inc. 2
XLMP XM-L LEDS RELTIVE SPETRL POWER DISTRIUTION Relative 100 Spectral Power Relative Radiant Power (%) 80 60 0 20 0 00 50 500 550 600 650 700 750-20 2600K -3700K T 3700K - 5000K T 5000K - 8300K T Wavelength (nm) RELTIVE FLUX VS. JUNTION TEMPERTURE (I F = 700 M) 100% 90% Relative Luminous Flux 80% 70% 60% 50% 0% 30% 20% 10% 0% 25 50 75 100 125 150 Junction Temperature (º) ree, of Inc. ree, of Inc. 3
XLMP XM-L LEDS ELETRIL Electrical haracteristics HRTERISTIS (Tj = 25º) (T J = 25 ) Forward urrent (m) 3000 2800 2600 200 2200 2000 1800 1600 100 1200 1000 800 600 00 200 0 2.00 2.20 2.0 2.60 2.80 3.00 3.20 3.0 3.60 Forward Voltage (V) THERML DESIGN The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ool White ambient in order to optimize lamp life and optical characteristics. 3500 3000 Maximum urrent (m) 2500 2000 1500 Thermal Design 1000 500 Rj-a = /W Rj-a = 7 /W Rj-a = 10 /W Rj-a = 15 /W 0 0 20 0 60 80 100 120 10 mbient Temperature (º) ree, of Inc. ree, of Inc.
XLMP XM-L LEDS RELTIVE FLUX VS. URRENT (T J = 25 ) Relative Luminous Flux (%) 350% 325% 300% 275% 250% 225% 200% 175% 150% 125% 100% 75% Typical Spatial Radiation Pattern 50% 25% 0% 0 200 00 600 800 1000 1200 100 1600 1800 2000 2200 200 2600 2800 3000 Forward urrent (m) RELTIVE HROMTIITY VERSUS URRENT ND TEMPERTURE (OOL WHITE) ool White 0.020 0.015 0.010 0.005 0.000-0.005-0.010-0.015-0.020 0 500 1000 1500 2000 2500 3000 urrent (m) Δx Δy Warm White 0.020 0.015 ree, of Inc. ree, of Inc. 0.010 5 0.005
XLMP XM-L LEDS RELTIVE HROMTIITY VERSUS URRENT ND TEMPERTURE (OOL WHITE) ool White 0.020 0.015 0.010 ool White 0.005 0.020 0.000 0.015-0.005 0.010-0.010 Δx Δy 0.005-0.015-0.020 0.000-0.005 25 50 75 100 125 150 Δx -0.010 Tsp ( ) Δy -0.015-0.020 RELTIVE Warm HROMTIITY White 0 500 VERSUS 1000 URRENT 1500 ND 2000 TEMPERTURE 2500 3000 (WRM WHITE) 0.020 urrent (m) 0.015 Warm 0.010 White 0.005 0.020 0.000 0.015-0.005 0.010-0.010 0.005-0.015 0.000-0.020-0.005 25 50 75 100 125 150-0.010 Tsp ( ) -0.015-0.020 0 500 1000 1500 2000 2500 3000 Δx Δy Δx Δy urrent (m) ree, of Inc. ree, of Inc. 6
0.000-0.005-0.010-0.015-0.020 25 50 75 100 125 150 RELTIVE HROMTIITY VERSUS URRENT ND TEMPERTURE (WRM WHITE) Tsp ( ) Δx Δy XLMP XM-L LEDS Warm White 0.020 0.015 0.010 0.005 0.000-0.005-0.010-0.015-0.020 25 50 75 100 125 150 Tsp ( ) Δx Δy TYPIL SPTIL DISTRIUTION 120 Relative Luminous Intensity (%) 100 80 60 0 20 0-100 -80-60 -0-20 0 20 0 60 80 100 ngle (º) ree, of Inc. ree, of Inc. 7
XLMP XM-L LEDS REFLOW SOLDERING HRTERISTIS In testing, ree has found XLamp XM-L LEDs to be compatible with JEDE J-STD-020, using the parameters listed below. s a general guideline, ree recommends that users follow the recommended soldering profile provided by the manufacturer of solder paste used. Note that this general guideline may not apply to all P designs and configurations of reflow soldering equipment. Profile Feature Lead-ased Solder Lead-Free Solder verage Ramp-Up Rate (Ts max to Tp) 3 /second max. 3 /second max. Preheat: Temperature Min (Ts min ) 100 150 Preheat: Temperature Max (Ts max ) 150 200 Preheat: Time (ts min to ts max ) 60-120 seconds 60-180 seconds Time Maintained bove: Temperature (T L ) 183 217 Time Maintained bove: Time (t L ) 60-150 seconds 60-150 seconds Peak/lassification Temperature (Tp) 215 260 Time Within 5 of ctual Peak Temperature (tp) 10-30 seconds 20-0 seconds Ramp-Down Rate 6 /second max. 6 /second max Time 25 to Peak Temperature 6 minutes max. 8 minutes max. Note: ll temperatures refer to the topside of the package, measured on the package body surface. ree, of Inc. ree, of Inc. 8
XLMP XM-L LEDS NOTES Lumen Maintenance Projections ree currently recommends a maximum drive current of 1500 m for XLamp XM-L white in designs seeking the ENERGY STR* 35,000 hour lifetime rating ( 9.1% luminous flux @ 6000 hours) or 25,000-hour lifetime rating ( 91.8% luminous flux @ 6000 hours). Please read the XLamp Long-Term Lumen Maintenance application note for more details on ree s lumen maintenance testing and forecasting. Please read the XLamp Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. * These lifetime ratings are based on the current ENERGY STR Solid State Lighting Luminaires V1.1 (December 12, 2008) and ENERGY STR Integral LED Lamps V1.0 (December 3, 2009) lumen maintenance criteria. Moisture Sensitivity In testing, ree has found XLamp XM-L LEDs to have unlimited floor life in conditions 30º / 85% relative humidity (RH). Moisture testing included a 168 hour soak at 85º / 85% RH followed by 3 reflow cycles, with visual and electrical inspections at each stage. Vision dvisory laim WRNING: Do not look at exposed lamp in operation. Eye injury can result. See LED Eye Safety at http://www.cree. com/products/pdf/xlamp_eyesafety.pdf. ree, of Inc. ree, of Inc. 9
.8 XLMP XM-L LEDS MEHNIL DIMENSIONS.7 3.9 ll measurements are ±.13 mm unless otherwise indicated. 0.6 6 5 3 2 1 0. NOTIE 6 REE ONFIDENTIL. THIS PLOT ND THE INFORMTION.7 ONTINED WITHIN RE THE PROPRIETRY ND NOTIE ONFIDENTIL INFORMTION OF REE, ONFIDENTIL. IN. THIS PLOT THIS PLOT ND THE INFORMTION MY NOT E OPIED, REPRODUED ONTINED OR DISLOSED WITHIN TO RE NY THE PROPRIETRY ND UNUTHORIZED PERSON WITHOUT ONFIDENTIL THE WRITTEN INFORMTION ONSENT OF REE, IN. THIS PLOT OF REE IN. MY NOT E OPIED, REPRODUED OR DISLOSED TO NY UNUTHORIZED PERSON WITHOUT THE WRITTEN ONSENT OF REE IN. 5 3 REVISONS 2 REV DESRIPTION Y NEW RELESE REV D DESRIPTION /15/10 dded die outline NEW DDSRELES 10/22/1 DDED DIMENSION FOR TOP OF FLSH dded D die 11/18/1 outli D 3.02 WS 3.09 DDED DIMENSION D FOR 1/5/11T D 3.02 WS 3.0 0. 0. D REOMMENDED STENIL PTTERN SHDED RE IS OPEN D 5.00 THIRD NGLE PROJETION UNLESS OTHERWISE SPEIFIED DIMENSIONS RE IN MILLIMETERS ND FTER FINISH. TOLERNE UNLESS SPEIFIED:.XX ±.25.XXX ±.125 X ±.5 5.00 FOR SHEET METL PRTS ONLY.X ± 1.5.XX ±.75.XXX ±.25 X ±.5 SURFE FINISH: 1.6 DRWN Y D. RONIN HEK PPROVED MTERIL FINL PROTETIVE FINISH 3.02 SIZE 3.02 Phone (919) 313-5300 0.5 Fax (919) 313-5558 0.73 OUTLINE DRWING, 5050 XM TITLE SLE 16.000 DRWING NO. 3 2 1 0/9/10 2610-00009 600 Silicon Drive Durham, N. 27703 SHEET OF REV. D 1 /1 0.73 0.5 3.8 2.8 0.5 3.8 2.8 0.5 5.00 5.00.8 Top View Side View ottom View.8 3.8 0.5 0.5.8 3.8 0.6.7 3.9 0.6.7 3.9 0.5 0.5.8 0..8 0..7.7 0.5 2.782 0.5 0. 2.782 0. 0. 0. 0. DRWN Y UNLESS OTHERWISE SPEIFIED 0. REOMMENDED STENIL PTTERN 60 DIMENSIONS RE IN D. RONIN 0/9/10 DRWN Y Du HEK SHDED RE IS OPEN MILLIMETERS ND FTER FINISH. UNLESS OTHERWISE SPEIFIED REOMMENDED STENIL PTTERN Ph REOMMENDED P SOLDER PD TOLERNE UNLESS SPEIFIED: DIMENSIONS RE IN D. RONIN 0/9/10 Fa HEK SHDED RE IS OPEN.XX ±.25 MILLIMETERS ND FTER FINISH. PPROVED Recommended REOMMENDED P SOLDER Solder PD Pad Recommended Stencil.XXX ± Pattern.125 TOLERNE UNLESS TITLE SPEIFIED: X ±.5.XX ±.25 PPROVED THIRD NGLE PROJETION (Shaded rea MTERIL OUTLINE DRWING, FOR Is SHEET Open).XXX ±.125 METL PRTS ONLY X ±.5 THIRD.X ± NGLE 1.5PROJETION MTERIL SIZE DRWING NO..XX ±.75 FOR SHEET METL PRTS ONLY.XXX ±.25 FINL PROTETIVE FINISH.X ± 1.5 2610-0000 X ±.5.XX ±.75 SLE SHE SURFE FINISH: 1.6.XXX ±.25 FINL PROTETIVE FINISH X ±.5 16.000 6 5 3 SURFE 2 FINISH: 1.6 1 6 5 3 2 ree, of Inc. ree, of Inc. 10
XLMP XM-L LEDS TPE ND REEL 6 5 NOTIE 6 5 REE ONFIDENTIL. THIS PLOT ND THE INFORMTION ONTINED WITHIN 6 RE THE PROPRIETRY ND 5 NOTIE ONFIDENTIL INFORMTION OF REE, IN. THIS PLOT REE ONFIDENTIL. THIS PLOT NOTIE ND THE INFORMTION MY NOT E OPIED, REPRODUED OR DISLOSED TO NY ONTINED REE UNUTHORIZED ONFIDENTIL. WITHIN RE THE PERSON THIS PROPRIETRY PLOT WITHOUT ND ND THE INFORMTION WRITTEN ONSENT ONFIDENTIL ONTINED OF REE INFORMTION IN. WITHIN RE OF THE REE, PROPRIETRY IN. THIS PLOT ND MY NOT ONFIDENTIL E OPIED, INFORMTION REPRODUED OF OR REE, DISLOSED IN. THIS TO PLOT NY UNUTHORIZED MY NOT E PERSON OPIED, WITHOUT REPRODUED THE WRITTEN OR DISLOSED ONSENT TO NY OF REE UNUTHORIZED IN. PERSON WITHOUT THE WRITTEN ONSENT D OF REE IN. D 2.00[.079] D P2 2.00[.079] 2.00[.079] P2.00[.157] P2 Po.00[.157].00[.157] Po Po Do1.50 +.10 +.0039.0591 -.00 -.0000 [ ] Do1.50 +.10 Do1.50 +.10 +.0039.0591 -.00 +.0039.0591 -.0000 [ ] -.00 1.75[.069] -.0000 [ ] E1 1.75[.069] E1 1.75[.069] E1 3 REV REV 12.00[.72] 5.50[.217]F NOMINL 12.00[.72] 5.50[.217]F NOMINL 12.00[.72] 5.50[.217]F 10.25 12.30 NOMINL [.8] [.0] MX 10.25 12.30 [.8] 10.25 E2 12.30 [.8] W [.0] MX [.0] MX E2 W E2 W 3 3 REV 2 2 REVISIONS 2DESRIPTION REVISIONS REVISIONS 1 1 Y 1 PP'D DESRIPTION Y PP'D DESRIPTION POKET SIZE Y PP'D o - POKET POKET 5.0mm SIZE SIZE [.213"] D o o - o - 5.0mm - 5.0mm [.213"] [.213"] D ll dimensions D in mm. o o - Ko - 5.0mm - 5.0mm 3.35mm [.213"] [.213"] [.132"] Ko Ko - - 3.35mm 3.35mm [.132"] [.132"] 3.0 5.0[.213] 3.0 o 5.0[.213] 3.0 5.0[.213] o o 6 NOTIE TIL. THIS PLOT ND THE INFORMTION HIN RE THE PROPRIETRY ND NFORMTION OF REE, IN. THIS PLOT PIED, REPRODUED OR DISLOSED TO NY PERSON WITHOUT THE WRITTEN ONSENT 5 8.00[.315] P 8.00[.315] 8.00[.315] P P 1.50[.059] 3 D1 1.50[.059] D1 1.50[.059] D1 7.0 7.0 2 1 REVISONS.36[.01] REV DESRIPTION T Y PP'D.36[.01] Loaded pocket count was T750.36[.01] DDS 11/8/10 S T D 3.35[.132] Ko 3.35[.132] 3.35[.132] Ko Ko REE REFERENE DRWING FOR TEK-PK DRWING 018275 5.0[.213] REE REFERENE DRWING FOR TEK-PK DRWING 018275 o DRWN Y 5.0[.213] UNLESS OTHERWISE REE REFERENE SPEIFIED DRWING FOR TEK-PK DRWING 018275 D. RONIN /23/10 600 Silicon Drive 5.0[.213] DIMENSIONS RE IN INHES Durham, N. 27703 o DRWN Y User Feed Direction HEK UNLESS OTHERWISE ND FTER SPEIFIED FINISH. o D. RONIN DRWN Y /23/10 600 Silicon Phone Drive (919) 313-5300 DIMENSIONS UNLESS TOLERNE RE OTHERWISE IN UNLESS INHES SPEIFIED: D. RONIN /23/10 Durham, 600 N. Fax Silicon (919) 27703Drive 313-5558 ND DIMENSIONS FTER FINISH. RE IN INHESHEK.XX ±.01 PPROVED Phone (919) Durham, 313-5300 N. 27703 ND FTER FINISH. HEK TITLE 8 TOLERNE UNLESS.XXX SPEIFIED: ±.005 1.75 3.35 Fax (919) Phone 313-5558 (919) 313-5300 TOLERNE END THODE SIDE.XX ± X UNLESS.01± SPEIFIED:.5 PPROVED Fax (919) 313-5558 THIRD NGLE PROJETION 6 5 STRT MTERIL.XX ±.01 3 TITLE FOR.XXX SHEET ± METL.005 PRTS ONLY XM 5050 PPROVED 2 RRIER TPE TITLE X ±.XXX.005 NOTIE.X.5 ±.06 THIRD NGLE PROJETION X ±.5 MTERIL SIZE DRWING NO. 200-00009 REV. REE ONFIDENTIL. THIS PLOT ND THE INFORMTION THIRD NGLE PROJETIONFOR SHEET METL.XX PRTS ± ONLY XM.03 MTERIL FOR SHEET METL PRTS ONLY FINL PROTETIVE FINISH XM 5050 5050 RRIER RRIER TPE TPE.XXX ±.010 INDEX QTY ITEM OMMENTS ONTNED WITHIN RE THE PROPRIETRY ND.X ±.06 202-00011 ONFIDENTIL INFORMTION OF REE, IN. THIS PLOT.X X ± ±.06.5 SIZE DRWING NO. REV..XX ±.03 SIZESLE DRWING NO. REV..XX ±.03 FINL PROTETIVE FINISH SHEET OF MY NOT E OPIED, REPRODUED OR DISLOSED TO NY.XXX SURFE ± FINISH:.010 63 12 1 1 200-00009-ORE FINL PROTETIVE FINISH UNUTHORIZED PERSON WITHOUT THE WRITTEN ONSENT.XXX ±.010 DRWING X ±.5 SLE202-00011 2 2 200-00009-REEL 202-00011 1 / 1 OF REE IN. 6 5 X ±.5 3 SLE 2 SHEET OF1 SURFE FINISH: 63 DRWING SLE SHEET 1OF/ 1 SURFE FINISH: 63 6 5 3 DRWING 2 SLE 1 1 / 1 6 5 3 2 1 NODE SIDE 7.0 1 D Trailer 160mm (min) of empty pockets sealed with tape (15 pockets min.) Loaded Pockets (1000 Lamps) Leader 00mm (min.) of empty pockets with at least 100mm sealed by tape (0 empty pockets min.) D 12. +.2.0 MESURED T HU 330 +.25 -.75 THIRD NGLE PROJETION UNLESS OTHERWISE SPEIFIED DIMENSIONS RE IN MILLIMETERS ND FTER FINISH. TOLERNE UNLESS SPEIFIED:.XX ±.25.XXX ±.125 X ±.5 FOR SHEET METL PRTS ONLY 16. +0.2.0 MESURED T HU.X ± 1.5 FINISH.XX ±.75.XXX ±.25 X ±.5 SURFE FINISH: 1.6 3.000 6 5 3 2 1 DRWN Y D. RONIN HEK PPROVED MTERIL 06/08/10 TITLE 13.1 ±.2 1.9±. 202-00012 600 Silicon Drive Durham, N. 27703 Phone (919) 313-5300 Fax (919) 313-5558 XM LODING SPE SHEET OF REV. 1 /1 21±. 12. +1.0 -.5 MESURED T EDGE 60 60 ree, of Inc. ree, of Inc. DRWN Y UNLESS OTHERWISE SPEIFIED DIMENSIONS RE IN INHES D. RONIN 09/29/09 ND FTER FINISH. HEK TOLERNE UNLESS SPEIFIED:.XX ±.01 PPROVED.XXX ±.005 TITLE X ±.5 THIRD NGLE PROJETION MTERIL REVISONS REV DESRIPTION Y PP'D 600 Silicon Drive 11 Durham, N. 27703 Phone (919) 313-5300 Fax (919) 313-5558 REEL, 13" X 12MM, 3 PIEE SNP
PKGING Humidity Humidity Indicator Indicator ard (inside (inside bag) bag) Dessicant Desiccant XLMP XM-L LEDS (inside bag) bag) Vacuum-Sealed Moisture Vacuum-Sealed arrier ag Moisture arrier ag Vacuum-Sealed Moisture Vacuum-Sealed arrier ag Moisture arrier ag REE Label in with ode ree in & ode, arcode Qty, Label Lot # REE Label in with oderee in & ode, arcode Qty, Label Lot # Label with with ustomer ree in ode, P/N, Qty, Qty, Lot #, Lot PO # Label with with ustomer ree in ode, P/N, Qty, Qty, Lot #, Lot PO ## Patent Label Patent Label Label with ustomer Order ode, Qty, Reel ID, PO # Label with ustomer Order ode, Qty, Reel ID, PO # Label with ustomer Order ode, Qty, Reel ID, PO# Label with ree in ode, Qty, Lot # ree, of Inc. ree, of Inc. 12
INNING & LELING LD-P REV 1 ree XLamp XM-L LED INTRODUTION This document describes the product nomenclature required to select and order ree s XLamp XM-L LEDs. XLamp XM-L LEDs are tested and sorted into bins which are then combined into orderable kits identified by an order code. ll XLamp LEDs are tested and sorted by color and brightness into a unique bin. Each bin contains LEDs from only one color and brightness group and is uniquely identified by a bin code. White XLamp LEDs are sorted by chromaticity (color) and luminous flux (brightness). LEDs are shipped on reels containing LEDs from one bin and are always labeled with the appropriate bin code. TLE OF ONTENTS in and Order-ode Format... 2 Performance Groups rightness... 2 Performance Groups hromaticity... 3 ree s Standard hromaticity Regions Plotted on the 1931 IE urve... 6 Standard Order odes and ins (XM-L NSI ool White)... 7 (XM-L NSI Neutral White)... 7 (XM-L NSI Warm White)... 8 Kits contain LEDs from a number of similar bins and are fully defined by their order codes. full explanation of the order codes for XLamp XM-L LEDs, as well as a list of standard order codes, is provided in this document. WWW.REE.OM/XLMP opyright 2010-2011 ree, Inc. ll rights reserved. The information in this document is subject to change without notice. ree, the ree logo and XLamp are registered trademarks of ree, Inc. This document is provided for informational purposes only and is not a warranty or a specification. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact ree Sales at sales@cree.com. ree, Inc. 600 Silicon Drive Durham, N 27703 US Tel: +1.919.313.5300
XLMP XM-L LED INNING & LELING IN ND ORDER-ODE FORMT in codes and order codes are configured in the following manner: Order ode in ode Series XML = XM-L Internal code SSSS-D-HHHH-NNNNNNNNN Kit number olor WT = White Series XML = XM-L Internal code Luminous flux group SSSS--WWW-FFF-GG- Internal code hromaticity group olor WT = White PERFORMNE GROUPS RIGHTNESS XLamp XM-L LEDs are tested for luminous flux and placed into one of the following luminous-flux groups: Group ode Min. Luminous Flux @ 700 m (lm) Max. Luminous Flux @ 700 m (lm) S6 182 200 T2 200 220 T3 220 20 T 20 260 T5 260 280 T6 280 300 U2 300 320 ree, of Inc. ree, Inc. This document is provided for informational purposes only and is not a warranty or a specification. For product specifications, please see the data sheets available of at www.cree.com. For warranty information, please contact ree Sales at sales@cree.com. 2
XLMP ML FMILY LEDS INNING & LELING, REV 1 PERFORMNE GROUPS HROMTIITY Region x y Region x y Region x y Region x y 0.2950 0.2970 0.2920 0.3060 0.298 0.3133 0.298 0.3133 0 0.2920 0.3060 0.2895 0.3135 0.2962 0.3220 0.308 0.3207 0 0 0D 0.298 0.3133 0.2962 0.3220 0.3028 0.330 0.3068 0.3113 0.3009 0.302 0.298 0.3133 0.308 0.3207 0.3009 0.302 0.2980 0.2880 0.2895 0.3135 0.2962 0.3220 0.3037 0.2937 0R 0.2950 0.2970 0.2870 0.3210 0.2937 0.3312 0.3009 0.302 0S 0T 0U 0.3009 0.302 0.2937 0.3312 0.3005 0.315 0.3068 0.3113 0.3037 0.2937 0.2962 0.3220 0.3028 0.330 0.3093 0.2993 0.308 0.3207 0.3028 0.330 0.3115 0.3391 0.3130 0.3290 1 0.3130 0.3290 0.3115 0.3391 0.3205 0.381 0.3213 0.3373 1 1 1D 0.31 0.3186 0.3130 0.3290 0.3213 0.3373 0.3221 0.3261 0.3068 0.3113 0.308 0.3207 0.3130 0.3290 0.31 0.3186 0.3068 0.3113 0.3005 0.315 0.3099 0.3509 0.31 0.3186 1R 0.31 0.3186 0.3099 0.3509 0.3196 0.3602 0.3221 0.3261 1S 1T 1U 0.3161 0.3059 0.3115 0.3391 0.3205 0.381 0.3231 0.3120 0.3093 0.2993 0.3028 0.330 0.3115 0.3391 0.3161 0.3059 0.3215 0.3350 0.3207 0.362 0.3290 0.3538 0.3290 0.317 2 0.3290 0.317 0.3290 0.3538 0.3376 0.3616 0.3371 0.390 2 2 2D 0.3290 0.3300 0.3290 0.317 0.3371 0.390 0.3366 0.3369 0.3222 0.323 0.3215 0.3350 0.3290 0.317 0.3290 0.3300 0.3222 0.323 0.3196 0.3602 0.3290 0.3690 0.3290 0.3300 2R 0.3290 0.3300 0.3290 0.3690 0.3381 0.3762 0.3366 0.3369 2S 2T 2U 0.3290 0.3180 0.3290 0.3538 0.3376 0.3616 0.3361 0.325 0.3231 0.3120 0.3207 0.362 0.3290 0.3538 0.3290 0.3180 0.3371 0.390 0.3376 0.3616 0.363 0.3687 0.351 0.355 3 0.351 0.355 0.363 0.3687 0.3551 0.3760 0.3533 0.3620 3 3 3D 0.30 0.327 0.351 0.355 0.3533 0.3620 0.3515 0.387 0.3366 0.3369 0.3371 0.390 0.351 0.355 0.30 0.327 0.3366 0.3369 0.3381 0.3762 0.380 0.380 0.30 0.328 3R 0.30 0.328 0.380 0.380 0.3571 0.3907 0.3515 0.387 3S 3T 3U 0.329 0.3307 0.363 0.3687 0.3551 0.3760 0.395 0.3339 0.3361 0.325 0.3376 0.3616 0.363 0.3687 0.329 0.3307 0.3530 0.3597 0.358 0.3736 0.361 0.380 0.3615 0.3659 0.3615 0.3659 0.361 0.380 0.3736 0.387 0.3702 0.3722 D 0.3590 0.3521 0.3615 0.3659 0.3702 0.3722 0.3670 0.3578 0.3512 0.365 0.3530 0.3597 0.3615 0.3659 0.3590 0.3521 0.3512 0.365 0.3571 0.3907 0.3668 0.3957 0.3590 0.3521 R 0.3590 0.3521 0.3668 0.3957 0.3771 0.03 0.3670 0.3578 S T U 0.3567 0.3389 0.361 0.380 0.3736 0.387 0.360 0.30 0.395 0.3339 0.358 0.3736 0.361 0.380 0.3567 0.3389 opyright 2009-2010 ree, Inc. ll rights reserved. The information in this document is subject to change without notice. ree, the ree logo and XLamp are registered trademarks of ree, Inc. This document is provided for informational purposes only and is not a warranty or a specification. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact ree Sales at sales@cree.com. 3
XLMP ML FMILY LEDS INNING & LELING, REV 1 PERFORMNE GROUPS HROMTIITY (ONTINUED) Region x y Region x y Region x y Region x y 0.3670 0.3578 0.3686 0.369 0.37 0.3685 0.3726 0.3612 51 0.3686 0.369 0.3702 0.3722 0.3763 0.3760 0.37 0.3685 52 53 5 0.37 0.3685 0.3763 0.3760 0.3825 0.3798 0.380 0.3721 0.3726 0.3612 0.37 0.3685 0.380 0.3721 0.3783 0.366 0.3702 0.3722 0.3719 0.3797 0.3782 0.3837 0.3763 0.3760 51 0.3719 0.3797 0.3736 0.387 0.3802 0.3916 0.3782 0.3837 52 53 5 0.3782 0.3837 0.3802 0.3916 0.3869 0.3958 0.387 0.3877 0.3763 0.3760 0.3782 0.3837 0.387 0.3877 0.3825 0.3798 0.3825 0.3798 0.387 0.3877 0.3912 0.3917 0.3887 0.3836 51 0.387 0.3877 0.3869 0.3958 0.3937 0.001 0.3912 0.3917 52 53 5 0.3912 0.3917 0.3937 0.001 0.006 0.0 0.3978 0.3958 0.3887 0.3836 0.3912 0.3917 0.3978 0.3958 0.3950 0.3875 0.3783 0.366 0.380 0.3721 0.3863 0.3758 0.380 0.3681 5D1 0.380 0.3721 0.3825 0.3798 0.3887 0.3836 0.3863 0.3758 0.3863 0.3758 5D2 0.3887 0.3836 5D3 0.3950 0.3875 5D 0.392 0.379 0.380 0.3681 0.3863 0.3758 0.392 0.379 0.3898 0.3716 0.3889 0.3690 0.3915 0.3768 0.3981 0.3800 0.3953 0.3720 61 0.3915 0.3768 0.391 0.388 0.010 0.3882 0.3981 0.3800 62 63 6 0.3981 0.3800 0.010 0.3882 0.080 0.3916 0.08 0.3832 0.3953 0.3720 0.3981 0.3800 0.08 0.3832 0.017 0.3751 0.391 0.388 0.3968 0.3930 0.00 0.3966 0.010 0.3882 61 0.3968 0.3930 0.3996 0.015 0.071 0.052 0.00 0.3966 62 63 6 0.00 0.3966 0.071 0.052 0.16 0.089 0.113 0.001 0.010 0.3882 0.00 0.3966 0.113 0.001 0.080 0.3916 0.080 0.3916 0.113 0.001 0.186 0.037 0.150 0.3950 61 0.113 0.001 0.16 0.089 0.222 0.127 0.186 0.037 62 63 6 0.186 0.037 0.222 0.127 0.299 0.165 0.259 0.073 0.150 0.3950 0.186 0.037 0.259 0.073 0.221 0.398 0.017 0.3751 0.08 0.3832 0.116 0.3865 0.082 0.3782 6D1 0.08 0.3832 0.080 0.3916 0.150 0.3950 0.116 0.3865 6D2 6D3 6D 0.116 0.3865 0.150 0.3950 0.221 0.398 0.183 0.3898 0.082 0.3782 0.116 0.3865 0.183 0.3898 0.17 0.381 0.17 0.381 0.183 0.3898 0.22 0.3919 0.203 0.3833 71 0.183 0.3898 0.221 0.398 0.281 0.006 0.22 0.3919 72 73 7 0.22 0.3919 0.281 0.006 0.32 0.028 0.300 0.3939 0.203 0.3833 0.22 0.3919 0.300 0.3939 0.259 0.3853 opyright 2009-2010 ree, Inc. ll rights reserved. The information in this document is subject to change without notice. ree, the ree logo and XLamp are registered trademarks of ree, Inc. This document is provided for informational purposes only and is not a warranty or a specification. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact ree Sales at sales@cree.com.
XLMP ML FMILY LEDS INNING & LELING, REV 1 PERFORMNE GROUPS HROMTIITY (ONTINUED) Region x y Region x y Region x y Region x y 0.221 0.398 0.259 0.073 0.322 0.096 0.281 0.006 71 0.259 0.073 0.299 0.165 0.36 0.188 0.322 0.096 72 73 7 0.322 0.096 0.36 0.188 0.30 0.212 0.385 0.119 0.281 0.006 0.322 0.096 0.385 0.119 0.32 0.028 0.32 0.028 0.385 0.119 0.9 0.11 0.03 0.09 71 0.385 0.119 0.30 0.212 0.96 0.236 0.9 0.11 72 73 7 0.9 0.11 0.96 0.236 0.562 0.260 0.513 0.16 0.03 0.09 0.9 0.11 0.513 0.16 0.65 0.071 0.259 0.3853 0.300 0.3939 0.359 0.3960 0.316 0.3873 7D1 0.300 0.3939 0.32 0.028 0.03 0.09 0.359 0.3960 7D2 7D3 7D 0.359 0.3960 0.03 0.09 0.65 0.071 0.18 0.3981 0.316 0.3873 0.359 0.3960 0.18 0.3981 0.373 0.3893 0.373 0.3893 0.18 0.3981 0.75 0.399 0.28 0.3906 81 0.18 0.3981 0.65 0.071 0.523 0.085 0.75 0.399 82 83 8 0.75 0.399 0.523 0.085 0.582 0.099 0.532 0.008 0.28 0.3906 0.75 0.399 0.532 0.008 0.83 0.3919 0.65 0.071 0.513 0.16 0.573 0.178 0.523 0.085 81 0.513 0.16 0.562 0.260 0.62 0.27 0.573 0.178 82 83 8 0.573 0.178 0.62 0.27 0.687 0.289 0.63 0.193 0.523 0.085 0.573 0.178 0.63 0.193 0.582 0.099 0.582 0.099 0.63 0.193 0.695 0.207 0.61 0.112 81 0.63 0.193 0.687 0.289 0.750 0.30 0.695 0.207 82 83 8 0.695 0.207 0.750 0.30 0.813 0.319 0.756 0.221 0.61 0.112 0.695 0.207 0.756 0.221 0.700 0.126 0.83 0.3919 0.532 0.008 0.589 0.021 0.538 0.3931 8D1 0.532 0.008 0.582 0.099 0.61 0.112 0.589 0.021 8D2 8D3 8D 0.589 0.021 0.61 0.112 0.700 0.126 0.66 0.03 0.538 0.3931 0.589 0.021 0.66 0.03 0.593 0.39 opyright 2009-2010 ree, Inc. ll rights reserved. The information in this document is subject to change without notice. ree, the ree logo and XLamp are registered trademarks of ree, Inc. This document is provided for informational purposes only and is not a warranty or a specification. For product specifications, please see the data sheets available at www.cree.com. For warranty information, please contact ree Sales at sales@cree.com. 5
XLMP XM-L LED INNING & LELING REE S STNDRD HROMTIITY REGIONS PLOTTED ON THE 1931 IE URVE NSI ool White 0.0 0.39 5000K 0.38 5700K 0.37 0.36 6500K 2S 2T 3S 3 y 0.35 0.3 0.33 8000K 0T 1S 1 1T 1 1D 2 2 2 2D 2U 3 3R 0.32 0.31 0.30 0.29 0S 0 0 0 0D 0U 0R 1 1R 1U 2R NSI 78.377 0.28 0.28 0.29 0.30 0.31 0.32 x 0.33 0.3 0.35 0.36 NSI Neutral and Warm White 0.6 0.5 0. 3000K 2700K y 0.3 0.2 0.1 0.0 0.39 0.38 0.37 0.36 0.35 3 3 5000K 3D 3 D 500K 51 52 51 52 5 53 5 53 5D1 5D2 51 000K 52 5D 5D3 5 61 53 62 61 6 62 63 6 6D1 63 6D2 61 6D 3500K 62 6D3 6 71 63 72 7 71 73 72 7D1 7 7D2 73 7D 71 7D3 81 72 7 82 8 73 81 83 8D1 82 8 8D2 8D 83 81 8D3 82 8 NSI 78.377 83 0.3 0.33 0.33 0.3 0.35 0.36 0.37 0.38 0.39 0.0 0.1 x 0.2 0.3 0. 0.5 0.6 0.7 0.8 0.9 ree, of Inc. ree, Inc. This document is provided for informational purposes only and is not a warranty or a specification. For product specifications, please see the data sheets available of at www.cree.com. For warranty information, please contact ree Sales at sales@cree.com. 6
XLMP XM-L LED INNING & LELING The following tables of order codes list flux minimums and chromaticity regions for XLamp XM-L LEDs. For other flux and chromaticity combinations, contact ree or an authorized distributor. STNDRD ORDER ODES ND INS (XM-L NSI OOL WHITE) XLamp XM-L LED Standard Order odes - White Min. Luminous Flux (lm) @ 700 m* hromaticity Regions Kit Number Group Flux (lm) NSI ool White (5000 K 8300 K) 0, 0, 0, 0D, 0R, 0S, 0T, 0U, 1, 1, 1, 1D, 1R, 1S, 1T, 1U, 2, 2, 2, 2D, 2R, 2S, 2T, 2U, 3, 3, 3R, 3S 0000T5051 T5 260 1, 1, 1, 1D, 1R, 1S, 1T, 1U, 2, 2, 2, 2D, 2R, 2S, 2T, 3, 3, 3S 0000T5053 1, 1, 1, 1D, 2, 2, 2, 2D 0000T5050 T6 280 0, 0, 0, 0D, 0R, 0S, 0T, 0U, 1, 1, 1, 1D, 1R, 1S, 1T, 1U, 2, 2, 2, 2D, 2R, 2S, 2T, 2U, 3, 3, 3R, 3S 0000T6051 1, 1, 1, 1D, 1R, 1S, 1T, 1U, 2, 2, 2, 2D, 2R, 2S, 2T, 3, 3, 3S 0000T6053 STNDRD ORDER ODES ND INS (XM-L NSI NEUTRL WHITE) XLamp XM-L LED Standard Order odes - White Min. Luminous Flux (lm) @ 700 m* hromaticity Regions Kit Number T Group Flux (lm) NSI Neutral White (3700 K 5000 K) T2 200 51, 52, 53, 5, 5D1, 5D2, 5D3, 5D, 61, 62, 63, 6, 61, 62, 63, 6 000LT20F6 3700 K, D, 51, 52, 53, 5, 51, 52, 53, 5 000LT30F5 300 K T3 220 51, 52, 53, 5, 51, 52, 53, 5, 51, 52, 53, 5, 5D1, 5D2, 5D3, 5D, 000LT30E5 000K 51, 52, 53, 5, 5D1, 5D2, 5D3, 5D, 61, 62, 63, 6, 61, 62, 63, 6 000LT30F6 3700 K 3, 3, 3, 3D 000LT0E3 5000 K 3, 3D,, 000LT0F 750 K T 20,,, D 000LT0E 500 K, D, 51, 52, 53, 5, 51, 52, 53, 5 000LT0F5 300 K 51, 52, 53, 5, 51, 52, 53, 5, 51, 52, 53, 5, 5D1, 5D2, 5D3, 5D, 000LT0E5 000 K 51, 52, 53, 5, 5D1, 5D2, 5D3, 5D, 61, 62, 63, 6, 61, 62, 63, 6 000LT0F6 3700 K 3, 3, 3, 3D 000LT50E3 5000 K T5 260 3, 3D,, 000LT50F 750 K,,, D 000LT50E 500 K T6 280 3, 3, 3, 3D 000LT60E3 5000 K * ree XLamp XM-L order codes specify only a minimum flux bin and not a maximum. ree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity restrictions specified by the order code. ree, of Inc. ree, Inc. This document is provided for informational purposes only and is not a warranty or a specification. For product specifications, please see the data sheets available of at www.cree.com. For warranty information, please contact ree Sales at sales@cree.com. 7
XLMP XM-L LED INNING & LELING STNDRD ORDER ODES ND INS (XM-L NSI WRM WHITE) XLamp XM-L LED Standard Order odes - White Min. Luminous Flux (lm) @ 700 m* hromaticity Regions Kit Number T Group Flux (lm) NSI Warm White (2700 K 3700 K) S6 182 71, 72, 73, 7, 7D1, 7D2, 7D3, 7D, 81, 82, 83, 8, 81, 82, 83, 8 000LS60F8 2900 K 81, 82, 83, 8, 81, 82, 83, 8, 81, 82, 83, 8, 8D1, 8D2, 8D3, 8D 000LS60E8 2700 K 61, 62, 63, 6, 61, 62, 63, 6, 61, 62, 63, 6, 6D1, 6D2, 6D3, 6D 000LT20E6 3500 K 61, 62, 63, 6, 6D1, 6D2, 6D3, 6D, 71, 72, 73, 7, 71, 72, 73, 7 000LT20F7 3200 K T2 200 71, 72, 73, 7, 71, 72, 73, 7, 71, 72, 73, 7, 7D1, 7D2, 7D3, 7D 000LT20E7 3000 K 71, 72, 73, 7, 7D1, 7D2, 7D3, 7D, 81, 82, 83, 8, 81, 82, 83, 8 000LT20F8 2900 K 81, 82, 83, 8, 81, 82, 83, 8, 81, 82, 83, 8, 8D1, 8D2, 8D3, 8D 000LT20E8 2700 K 61, 62, 63, 6, 61, 62, 63, 6, 61, 62, 63, 6, 6D1, 6D2, 6D3, 6D 000LT30E6 3500 K T3 220 61, 62, 63, 6, 6D1, 6D2, 6D3, 6D, 71, 72, 73, 7, 71, 72, 73, 7 000LT30F7 3200 K 71, 72, 73, 7, 71, 72, 73, 7, 71, 72, 73, 7, 7D1, 7D2, 7D3, 7D 000LT30E7 3000 K T 20 61, 62, 63, 6, 61, 62, 63, 6, 61, 62, 63, 6, 6D1, 6D2, 6D3, 6D 000LT0E6 3500 K * ree XLamp XM-L order codes specify only a minimum flux bin and not a maximum. ree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity restrictions specified by the order code. ree, of Inc. ree, Inc. This document is provided for informational purposes only and is not a warranty or a specification. For product specifications, please see the data sheets available of at www.cree.com. For warranty information, please contact ree Sales at sales@cree.com. 8