For Reference Only 1/16 Pyroelectric infrared sensor IRS-B345ST03 Preliminary Product specification 1 Scope This product specification is applied to parallel-quad element type pyroelectric infrared sensor IRS-B345ST03 used to Sensor light and Consumer electronic equipment. Please contact us when using this product for any other applications than described in the above. 2 Murata Part Number 500pcs/reel : IRS-B345ST03-R2 2000pcs/reel : IRS-B345ST03-R1
For Reference Only 2/16 3 Product figures / dimensions 3-1 Figure / dimensions and inner electrode dimension 1.4 out put terminal (Vout) 0.9 (4) (5) + + - - (3) (2) (1) power supply terminal (Vin) Unit: mm General tolerance: ±0.2mm Fig.1 Figure / dimensions and inner electrode dimension
For Reference Only 3/16 3-2 Internal circuit diagram Power supply terminal (Vin) (RG) Out put terminal (Vout) GND Fig.2 Internal circuit diagram 4 Mark on product body Part number and monthly number are numbering on the side of package. 4-1 Part number code and Trade code Part number code: 03 4-2 Production Month Printed on the top of sensor in JEITA RC-0901 code. Year Month 1 2 3 4 5 6 7 8 9 10 11 12 2010 2014 N P Q R S T U V W X Y Z 2011 2015 a b c d e f g j m 2012 2016 n r t u 2013 2017 A B C D E F G H J K L M 4-3 Marking example (October 2010) 0 3 X Fig.3 Marking (example)
For Reference Only 4/16 5 Ratings and Characteristics (25 C±3 50%±30%RH) 5-1 Responsivity (Rv) Min. Typ. Responsivity (Rv) 2.7 mvpp 3.1 mvpp Responsivity is measured with following system. Black Body 140mm Lock-in Amp.(1Hz) +5V 500K Mechanical Chopper (1Hz) d 47kohm s 22uF g Infrared Sensor Oscilloscope Fig.4 Test system of responsivity 5-2 White Noise Level White Noise Conditions for measurement 200mVpp Max. Test circuit Measure Point Environment : Shown in fig.5. : Across OUT and GND as shown in fig.5. : In the electrically and optically shielded box. 5VDC 33k 10n 33k 22n d g s 1n A 47k 10k A 10k 2.2meg 22u 47u LM358 1n 10k 33k 22k 1meg LM358 4.7k 1n OUT 22u GND Fig.5 Test circuit for white noise Gain:76.5dB (x6700)
70 70 For Reference Only 5/16 5-3 Source Voltage Source voltage(vs) 0.3 to 1.5 V Conditions for measurement Test circuit : Shown in fig.6 Measure Point : Across OUT and GND as shown in fig.6. Environment : In the electrically and optically shielded box. Fig.6 Test circuit for Source Voltage 5-4 Supply Voltage Range 2.0~15.0 VDC 5-5 Field of View (For reference) Field of View means the designed value of angle that both of infrared receiving electrode A and B can be visible. + + - - 50 50 1.4 mm Fig.7 Field of View
Transmission ratio (%) For Reference Only 6/16 5-6 Optical Filter (For reference) Transmittance : see the graph shown in fig.8. Thickness : 0.5mm Wave number ( cm -1 ) Fig.8 Transmittance of optical filter (example) 6 Operating Temperature -40 ~ 70 7 Storage Temperature -40 ~ 85
0.35~0.40 (3.9) 1.90~2.10 1.00~1.10 2.40~2.60 3.30~3.50 (3.9) (4.7) For Reference Only 7/16 8. Standard Land Pattern Power supply terminal (Vin) (4.7) GND Land Pattern GND Pattern 3.15~3.35 3.65~3.75 Output terminal(vout) 6.00 more Fig.9 Standard land pattern GND Unit: mm Notes : Please avoid the signal line and the power supply line in the dashed line. In addition, please design the ground pattern except Vin and Vout electrode in this area.
For Reference Only 8/16 9 Soldering Conditions Following figure shows temperature profile when reflow soldering. Cleaning after reflow soldering should not be applied. Flow soldering should not be applied. Please contact us when using other reflow profile except following reflow profile. 255 Temp.( ) Peak temperature on product surface 255, 5sec. Max. 220 2.0 /sec Max 加 熱 部 Heating 220 Min. 2.0 /sec Max 180 徐 冷 Gradual in air 150 100 3.5 /sec Max 予 熱 Pre - Heating 150-180 昇 温 時 間 Heating period 80-100 sec. (20sec.Min.) 60 sec.max. 60 sec.min. Time(sec.) Fig.10 Soldering condision
For Reference Only 9/16 10 Packing and Marking The tape for pyroelectric infrared sensor shall be clockwise. The feeding holes shall be to the right side as the tape is pulled toward the user. A reel shall contain 500pcs or 2,000pcs of pyroelectric infrared sensor and its reel label shall be clearly marked with part number, quantity, and inspection number. The product which has ROHS-Y<*> mark on the packaging label is compliance with RoHS directives. The alphabet in blank <*> will be changed A to B, B to C, and so on with every revision of the ROHS directives. Please refer to the document, "The Marking for the directives on the restriction of the hazardous substances' use," to check the directives corresponding to alphabets in <*>.
For Reference Only 10/16 トレーラー 部 Trailer 製 品 挿 入 部 Sensor contained シール 部 Weld 100mm Min. トップカバーテープ Cover Tape リール Reel 160-1140 空 エンボス 部 Empty Emboss 100-200 リーダー 部 Leader 400-560 φ:330 wide:21.5 unit:mm (5) (4) (1) (2) (3) Fig.11 Emboss tape
For Reference Only 11/16 500pcs/reel W1 : 13.0±1.0mm W2 : 17.0±1.0mm W3: 12.5±1.0mm 2000pcs/reel W1 : 13.4±1.0mm W2 : 17.4±1.0mm Fig.12 Reel Size
For Reference Only 12/16 リール Reel ラベルⅡ LabelⅡ 外 装 箱 (タ ンホ ール) Outer box (Carton box) Packaging Quantity & Dimension of Packaging Packing Quantity Dimension (mm) (pcs.) L W D L 500 (1 reel) 1,000 (2reel) 190 190 100 D 防 湿 帯 電 防 止 袋 Anti-humidity Anti-ESD package ラベルⅠ LabelⅠ 1,500 (3 reel) 2,000 (1 reel) 4,000 (2 reels) 6,000 (3 reels) 8,000 (4 reels) 10,000(5 reels) 350 350 120 W Fig.13 Packing Packing Quantity Max. : 1,500pcs.. (=500pcs. x 3reels) Max. : 10,000pcs.. (=2,000pcs. x 5reels) If there is space in the box, cushion is packed as shock absorber. Materials for packing and the packing amount might change the content without a previous notice. * Label I (EIAJ D) indicates the following items. - Part name - QTY/Box - Inspection Number * Label II (EIAJ C3) indicates the following items. - Part name - QTY/Reel - Inspection Number *The product should be soldered within 180 days from delivery. When unpacked, the product should be stored in an atmosphere of below 25degC and below 65%RH.
For Reference Only 13/16 11 Reliability Judgment criteria for 11-1 to 11-7. After each one of the test, the sensor is kept for three hours at room temperature, then it is evaluated with the following criteria. Table1. Judgment criteria Items Judgment criteria Responsivity Within ±20% shift from initial value White noise Max. 300mVpp Source voltage 0.3 to 1.5V at 25deg.C 11-1 High temperature 100 C+/-2 C for 500hours 11-2 Low temperature -40 C+/-2 C for 500hours 11-3 Humidity 60 C+/-2 C, 93%RH+2/-3%RH for 500hours 11-4 Air heat cycle test 20 times of the following cycle. Cycle condition : -25 C±2 C, 30min. Room temp. 30min. 55 C±2 C, 30min. Room temp 11-5 Vibration Apply vibration of amplitude of 1.5mm with 10 to 55Hz bands to plus/minus of each of 3 perpendicular directions (x, y, z) for an hour. 11-6 Shock Apply 3 impacts of 100G and 6ms in plus/minus directions of 3 perpendicular axis (x, y, z). (1G=9.80665m/s 2 ) 11-7 Soldering heat 2 times of soldering test on fig.10. The second is returned to room temperature after the first soldering test.
For Reference Only 14/16 12 Caution 12-1 Limitation of Applications Please avoid using this product for the applications listed below which require especially high reliability for the prevention of defects that might directly cause damage to the third party's life, body or property. When this product is used for the applications listed below, we shall not be liable for any claims on the product. 1. Aircraft equipment 2. Aerospace equipment 3. Undersea equipment 4. Power plant control equipment 5. Medical equipment 6. Transportation equipment (vehicles, trains, ships, etc.) 7. Traffic signal equipment 8. Data-processing equipment 9. Application of similar complexity and/or reliability requirement to the applications listed in the above 12-2 Fail-safe Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure of our product.
For Reference Only 15/16 13 Caution in use 13-1 Notice in design 1) In the case of outdoor use, suitable optical filter and water and humidity proof structure should be applied. 2) To prevent failure or malfunction, Please use a stabilized power supply. 3) Please avoid using the sensor in the following conditions because it may cause failure or malfunction ; a) In such a fluid as water, alcohol etc. corrosive gas (SO 2, Cl 2, NO X etc.) or sea breeze. b) In high humidity. c) In a place exposed directly to sunlight or headlight of automobile. d) In a place exposed to rapid ambient temperature change. e) In a place exposed directly to blow from air-conditioner or heater. f) In a place exposed to strong vibration. g) In a place exposed to strong electromagnetic field. h) In such a place where infrared ray is shaded. i) In such a place are charge field and static electricity field. j) In any other place similar to the above (a) through (h). 13-2 Notice in handling and storage 1) Optical filter of sensor should not be scratched or soiled. 2) Strong shock should be avoided. 3) It may malfunction under electrostatics and electromagnetic field. Please use it after enough evaluating. 4) Electrostatics and strong electromagnetic field should be avoided. 5) Sensor should be kept on conductive sponge 6) High temperature, high humidity, fluid as water or alcohol etc., corrosive gas ( SO2, Cl2, NOX etc.) and sea breeze should be avoided. 7) Store the products where the temperature and relative humidity do not exceed -10 to 40 degrees centigrade, and 30 to 80%RH. Use the products within 6 months after receiving.
For Reference Only 16/16 13-3 Notice in mounting 1) Cleaning after reflow soldering should not be applied. Optical filter of sensor should not be soiled because it may cause failure or malfunction. 2) Please follow soldering conditions described in the specification. This product can permanently stop operating if the piezoelectric(pyroelectric) characteristic is decreased due to excessive heating. 14 Note 1) Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. 2) You are requested not to use our product deviating from the agreed specifications. 3) We consider it not to appropriate to include any terms and conditions with regard to the business transaction in the product specifications, drawings or other technical documents. Therefore, if your technical documents as above include such terms and conditions such as warranty clause, product liability clause, or intellectual property infringement liability clause, they will be deemed to be invalid.