Cisco Networking Professional-6Months Project Based Training Core Topics Cisco Certified Networking Associate (CCNA) 1. ICND1 2. ICND2 Cisco Certified Networking Professional (CCNP) 1. CCNP-ROUTE 2. CCNP-SWITCH 3. CCNP-TSHOOT CCNA DESCRIBE HOW A NETWORK WORKS Describe the purpose and functions of various network devices Select the components required to meet a network specification Use the OSI and TCP/IP models and their associated protocols to explain how data flows in a network Describe the purpose and basic operation of the protocols in the OSI and TCP models Determine the path between two hosts across a network Describe the components required for network and Internet communications Differentiate between LAN/WAN operation and features CONFIGURE, VERIFY AND TROUBLESHOOT A SWITCH WITH VLANS AND INTERSWITCH COMMUNICATIONS Select the appropriate media, cables, ports, and connectors to connect switches to other network devices and hosts Explain the technology and media access control method for Ethernet networks
Explain network segmentation and basic traffic management concepts Explain basic switching concepts and the operation of Cisco switches Perform and verify initial switch configuration tasks including remote access management Describe enhanced switching technologies (including: VTP, STP, VLAN, PVSTP, 802.1q) Describe how VLANs create logically separate networks and the need for routing between them Configure, verify, and troubleshoot VLANs Configure, verify, and troubleshoot trunking on Cisco switches Configure, verify, and troubleshoot InterVLAN routing Configure, verify, and troubleshoot VTP Configure, verify, and troubleshoot STP operation Interpret the output of various show and debug commands to verify the operational status of a Cisco switched network. Implement basic switch security (including: port security, trunk access, management vlan other than vlan1, etc.) IMPLEMENT AN IP ADDRESSING SCHEME AND IP SERVICES TO MEET NETWORK REQUIREMENTS IN A MEDIUM-SIZE ENTERPRISE BRANCH OFFICE NETWORK Describe the operation and benefits of using private and public IP addressing Explain the operation and benefits of using DHCP and DNS Configure, verify and troubleshoot DHCP and DNS operation on a router Implement static and dynamic addressing services for hosts in a LAN environment Calculate and apply an addressing scheme including VLSM IP addressing to a network Determine the appropriate classless addressing scheme using VLSM and summarization to satisfy addressing requirements in a LAN/WAN environment Describe IPv6 addresses Identify and correct common problems associated with IP addressing and host configurations CONFIGURE, VERIFY, AND TROUBLESHOOT BASIC ROUTER OPERATION AND ROUTING ON CISCO DEVICES Describe basic routing concepts (including: packet forwarding, router lookup process) Select the appropriate media, cables, ports, and connectors to connect routers to other network devices and hosts Configure, verify, and troubleshoot RIPv2 Connect, configure, and verify operation status of a device interface Manage IOS configuration files. (including: save, edit, upgrade, restore) Manage Cisco IOS Compare and contrast methods of routing and routing protocols Configure, verify, and troubleshoot OSPF Configure, verify, and troubleshoot EIGRP Verify network connectivity (including: using ping, traceroute, and telnet or SSH) Troubleshoot routing issues Verify router hardware and software operation using SHOW & DEBUG commands. Implement basic router security
EXPLAIN AND SELECT THE APPROPRIATE ADMINISTRATIVE TASKS REQUIRED FOR A WLAN Describe standards associated with wireless media (including: IEEE, WI-FI Alliance, ITU/FCC) Identify and describe the purpose of the components in a small wireless network. (Including: SSID, BSS, ESS) Identify the basic parameters to configure on a wireless network to ensure that devices connect to the correct access point Compare and contrast wireless security features and capabilities of WPA security (including: open, WEP, WPA-1/2) IMPLEMENT, VERIFY, AND TROUBLESHOOT NAT AND ACLS IN A MEDIUM-SIZE ENTERPRISE BRANCH OFFICE NETWORK Describe the purpose and types of ACLs Configure and apply ACLs based on network filtering requirements using CLI Configure and apply an ACL to limit telnet and SSH access to the router using CLI Verify and monitor ACLs in a network environment Troubleshoot ACL issues Explain the basic operation of NAT Configure NAT (Static, Dynamic, Overload )for given network requirements using CLI Troubleshoot NAT issues IMPLEMENT AND VERIFY WAN LINKS Describe different methods for connecting to a WAN Configure and verify a basic WAN serial connection Configure and verify Frame Relay on Cisco routers Troubleshoot WAN implementation issues Configure and verify a PPP connection between Cisco routers CCNP CCNP: ROUTE The ROUTE 642-902 exam will certify that the successful candidate has the knowledge and skills necessary to use advanced IP addressing and routing in implementing scalable and secure Cisco ISR routers connected to LANs and WANs. Implement an EIGRP based solution, given a network design and a set of requirements Determine network resources needed for implementing EIGRP in a network. Create an EIGRP implementation plan. Create an EIGRP verification plan. Configure EIGRP routing.
Verify an EIGRP solution was implemented properly using show and debug commands. Document the verification results for an EIGRP implementation Implement a multi-area OSPF Network, given a network design and a set of requirements Determine network resources needed for implementing OSPF on a network. Create an OSPF implementation plan. Create an OSPF verification plan. Configure OSPF routing. Verify OSPF solution was implemented properly using show and debug commands. Document the verification results for an OSPF implementation plan Implement an ebgp based solution, given a network design and a set of requirements Determine network resources needed for implementing ebgp on a network. Create an ebgp implementation plan. Create an ebgp verification plan. Configure ebgp routing. Verify ebgp solution was implemented properly using show and debug commands. Document verification results for an ebgp implementation plan Implement an IPv6 based solution, given a network design and a set of requirements Determine network resources needed for implementing IPv6 on a network. Create an IPv6 implementation plan. Create an IPv6 verification plan. Configure IPv6 routing. Configure IPv6 interoperation with IPv4. Verify IPv6 solution was implemented properly using show and debug commands. Document verification results for an IPv6 implementation plan Implement an IPv4 or IPv6 based redistribution solution, given a network design and a set of requirements Create a redistribution implementation plan based upon the results from a redistribution analysis. Create a redistribution verification plan. Configure a redistribution solution. Verify that a redistribution was implemented. Document results of a redistribution implementation and verification plan. Identify the differences between implementing an IPv4 and IPv6 redistribution solution Implement Layer 3 Path Control Solution Create a Layer 3 path control implementation plan based upon the results of the redistribution analysis. Create a Layer 3 path control verification plan. Configure Layer 3 path control. Verify that a Layer 3 path control was implemented. Document results of a Layer 3 path control implementation and verification plan. Implement basic teleworker and branch services. Describe broadband technologies. Configure basic broadband connections. Describe basic VPN technologies. Configure GRE. Describe branch access technologies
CCNP: SWITCH The SWITCH 642-813 exam will certify that the successful candidate has important knowledge and skills necessary to to plan, configure and verify the implementation of complex enterprise switching solutions using Cisco s Campus Enterprise Architecture. The SWITCH exam also covers secure integration of VLANs, WLANs, voice and video into campus networks. Implement VLAN based solution, given a network design and a set of requirements Determine network resources needed for implementing a VLAN based solution on a network. Create a VLAN based implementation plan. Create a VLAN based verification plan. Configure switch-to-switch connectivity for the VLAN based solution. Configure loop prevention for the VLAN based solution. Configure Access Ports for the VLAN based solution. Verify the VLAN based solution was implemented properly using show and debug commands. Document the verification after implementing a VLAN solution Implement a Security Extension of a Layer 2 solution, given a network design and a set of requirements Determine network resources needed for implementing a Security solution. Create a implementation plan for the Security solution. Create a verification plan for the Security solution. Configure port security features. Configure general switch security features. Configure private VLANs. Configure VACL and PACL. Verify the Security based solution was implemented properly using show and debug commands. Document the verification results after implementing a Security solution Implement Switch based Layer 3 services, given a network design and a set of requirements Determine network resources needed for implementing a Switch based Layer 3 solution. Create an implementation plan for the Switch based Layer 3 solution. Create a verification plan for the Switch based Layer 3 solution. Configure routing interfaces. Configure Layer 3 Security. Verify the Switch based Layer 3 solution was implemented properly using show and debug commands. Document the verification results after implementing a Switch based Layer 3 solution Prepare infrastructure to support advanced services Implement a Wireless Extension of a Layer 2 solution. Implement a VoIP support solution. Implement video support solution Implement High Availability, given a network design and a set of requirements Determine network resources needed for implementing High Availability on a network. Create a High Availability implementation plan. Create a High Availability verification plan. Implement first hop redundancy protocols.
Implement switch supervisor redundancy. Verify High Availability solution was implemented properly using show and debug commands. Document results of High Availability implementation and verification CCNP: TSHOOT The TSHOOT 642-832 exam will certify that the successful candidate has important knowledge and skills necessary to: 1) Plan and perform regular maintenance on complex enterprise routed and switched networks. 2) Use technology-based practices and a systematic ITIL-compliant approach to perform network troubleshooting. Maintain and monitor network performance Develop a plan to monitor and manage a network. Perform network monitoring using IOS tools. Perform routine IOS device maintenance. Isolate sub-optimal internetwork operation at the correctly defined OSI Model layer Troubleshoot Multi Protocol system networks Troubleshoot EIGRP, OSPF & ebgp. Troubleshoot routing redistribution solution. Troubleshoot a DHCP client and server solution. Troubleshoot NAT. Troubleshoot first hop redundancy protocols. Troubleshoot IPv6 routing. Troubleshoot IPv6 and IPv4 interoperability. Troubleshoot switch-to-switch connectivity for the VLAN based solution. Troubleshoot loop prevention for the VLAN based solution. Troubleshoot Access Ports for the VLAN based solution. Troubleshoot private VLANS. Troubleshoot port security. Troubleshoot general switch security. Troubleshoot VACLs and PACLs. Troubleshoot switch virtual interfaces (SVIs). Troubleshoot switch supervisor redundancy. Troubleshoot switch support of advanced services (i.e., Wireless, VOIP and Video). Troubleshoot a VoIP support solution. Troubleshoot a video support solution. Troubleshoot Layer 3 Security. Troubleshoot issues related to ACLs used to secure access to Cisco routers. Troubleshoot configuration issues related to accessing the AAA server for authentication purposes. Troubleshoot security issues related to IOS services (i.e.,finger, NTP, HTTP, FTP, RCP etc.) Call for Enquiry at: 7827979099