All round in Motion Control Rotating, linear and combinations of both! know-how makes the difference

All round in Motion Control Rotating, linear and combinations of both! know-how makes the difference

How state-of-the-art are your drive solutions? As a manufacturer you face complex challenges. The world around you changes, competition increases and customers require more functionality for (preferably) lower Total Cost of Ownership. This requires multidisciplinary, stateof-the-art solutions and that means that your engineers not only must have knowledge of electrical and mechanical drive systems, but also of digital control technology, field bus and motion control. And though it seems easier (mainly thanks to the Internet) to find the right components quickly, there is nothing further from the truth, because mistakes are thus made more quickly! In short, it comes down to expertise, experience and an innovative approach nowadays! Early involvement is better Many engineers think too quickly in terms of practical solutions. Often out of habit and / or because they are accustomed to certain products and systems. That inhibits innovation. The experts from Schoonhoven ERIKS Aandrijftechniek (formerly Elmeq) approach each design problem with an open mind and are used to 'outside the box' thinking. They also have more than 30 years experience and they know the opportunities in the field of motion control and linear and rotary drives like no others. By early involvement with these experts you will be able to work faster, will become more targeted and develop more effectively! Multidisciplinary development Developing with ERIKS Aandrijftechniek means working with engineers of various disciplines: electrical, mechanical, pneumatic, hydraulic and electronic (hardware and software). Besides this, they know how the European Machinery Directive (2006/42/EC) must be applied and are aware of all relevant safety and / or industryrelated guidelines. This lays the solid foundation for an integrated optimum design, which optimally combines modern electronics with state-of-the-art engine technology. Realising this requires strong teamwork. ERIKS Aandrijftechniek has such a team and that team is ready for you! Standard or custom? ERIKS Aandrijftechniek has a comprehensive product range and is within the ERIKS group surrounded by specialists who can deliver complementary products such as timing belts, chains, bearings, pneumatic and hydraulic components, etc. This paves the way for un unprecedented variety of combinations, allowing rapid, adequate solutions for most issues within driving range. And when the answer is not found in the standard program, ERIKS Aandrijftechniek designs, develops, produces and delivers special solutions, including additional technical and operational services. Feedback from practice The engineers of ERIKS Aandrijftechniek /Power Transmissions are in constant contact with the developing departments of their (A) suppliers. Practical experiences are exchanged and they result in product optimisation. Also, this targeted communication is important in the development of special drives, motors and controllers with which ERIKS scores high in the demanding OEM market. What can you expect from a co-maker? At your request, we will supply. It could be easy as that, but this is not always how it works. When the technical specialists of ERIKS Aandrijftechniek know in which application the requested product is put, they might suggest a

much better solution. In this way, by introducing its knowledge and experience, ERIKS Aandrijftechniek makes a positive contribution to your innovation and development. This results in an attractive reduction of both development time and costs, and consequently in a lower cost for your machine. So you may be able to produce better product properties. Here you should think of lower energy, higher performance and / or a better ergonomic and aesthetic design. Production and testing facilities Demonstrating a flawless operation is the best proof. Therefore ERIKS Aandrijftechniek has the necessary built-in facilities. For example, the electro-test department has a "Faraday cage" to perform pre-compliance EMC testing. In addition, vibration testing and temperature tests can be done. A well thought-out (lean) assembly line means short lead times. The ERIKS group owns a cleanroom for assembling precision mechanical and medical systems. Finally, there are numerous options for products with special codes, cable packages and / or other add-ons. Naturally, the products will be packed according to the wishes and requirements of the customer after a careful check at the output department. There is a wide choice from individually tailored to bulk packaging. ERIKS Aandrijftechniek - Schoonhoven It is the solution that counts! From high quality standard solutions till perfectly customized motion control, engineering and service! That s in a few words the strength of ERIKS Aandrijftechniek in Schoonhoven (formerly Elmeq). An excellent complementary product range, short communication lines and well-trained engineers and technical specialists lay the foundation for this. With over thirty years of experience, ERIKS Aandrijftechniek realizes innovative solutions in the field of motion control and linear and rotary drives. ERIKS Aandrijftechniek analyzes, advises, coordinates and supplies (standard) components. ERIKS Aandrijftechniek also develops and manufactures customer specific solutions and performs maintenance, repairs, overhauls and modifications. It goes without saying that factors such as sustainability, human(-) and environment-friendly, energy efficient are taken into account. Just like Corporate Social Responsibility (CSR). With complete conviction the experts of ERIKS Aandrijftechniek choose the best solutions. For you and also for your customers!

ERIKS Aandrijftechniek supplies to major OEMs which develop and produce: (Special) machines Automatic (company) doors Graphic machines Production lines for semiconductor Handling Systems (pick-and-place/multi axis robots) Power savings systems Production lines for the food sector Pharmaceutical / Medical Equipment Devices for comfort and rehabilitation Agricultural / horticultural machines Machines for use in livestock Solutions for the mobile sector Our A-suppliers

A selection from the extensive product range: Rotary and linear motors (AC, asynchronous, synchronous, DC servo, AC servo and steppers) Gearboxes (worm, gear, planetary and bevel gearboxes) Encoders, resolvers, brakes and tacho Amplifiers and controls: 1, 2 and 4 quadrant DC brush and brushless amplifiers AC servo drives and stepper drives Motion controller, PLCs, IPCs Cable assemblies PCB design and production Developing (embedded) software Implement EMC pre-compliance testing Fieldbus (Profibus DP / PA, Industrial Ethernet, CANopen, PROFINET, etc.) Actuators (confort, industrial and heavy duty) Direct drive linear motors Spindles (trapezoidal, helix and ball screw) Linear units with spindle or toothed belt, if desired with (integrated) motor, encoder, analogue feedback, limit switches, etc. Flexures Machined Springs

ERIKS Aandrijftechniek Schoonhoven Motion control, rotating and linear drives Broeikweg 25 2871 RM Schoonhoven T +31 (0) 182 30 34 56 F +31 (0) 182 38 69 20 E info.schoonhoven@eriks-at.nl ERIKS Aandrijftechniek Belgium Motion control, rotating and linear drives T +32 (0) 51 25 98 11 F +32 (0) 18 23 86 920 E sales@elmeq.be www.elmeq.be ERIKS Aandrijftechniek Roermond Mechanical drives and hydraulic systems www.eriks-aandrijftechniek.nl ERIKS Aandrijftechniek Groningen Power transmissions for MRO market www.wielens.nl ERIKS Aandrijftechniek Rotterdam Power transmissions for MRO market www.erxs.nl ERIKS Aandrijftechniek shortlist: Thorough knowledge of and experienced with motion control, linear and rotary drives Innovative products and applications, product innovation as drive Optimal informed of relevant Directives (Machinery Directive, ATEX, FDA, Safety, EMC, LV, etc. Technical advice, engineering and design by experienced electrical engineers, software engineers and mechanical engineers A co-maker who thinks outside the box as the basis for innovative solutions Extensive program components with a large number of premium brands and private labels In-house testing facilities ISO 9001:2008 certified Complimentary services like (lean) production and assembly Computer-aided project monitoring Experienced, fast, flexible, robust, nononsense ERIKS Aandrijftechniek is part of the ERIKS group, an international industrial service provider offering a wide range of high-quality mechanical engineering components and associated technical and logistics services. ERIKS current product range, including the technical and logistics services that form part of it, is divided into five core activities: sealing technology, power transmission including electromechanical services and condition monitoring, flow technology, industrial plastics and tools & maintenance products. The ERIKS companies belong to the holding company SHV. know-how makes the difference