HP SCOM Management Packs User Guide

HP SCOM Management Packs User Guide Abstract This guide describes the HP extensions for Microsoft System Center Operations Manager that are provided as part of HP Insight Control for Microsoft System Center. This guide is intended for use by system integrators and network administrators who are familiar with HP-branded server system products and Microsoft System Center. HP Part Number: 696060-003 Published: September 2012 Edition: 1

Copyright 2012 Hewlett-Packard Development Company, L.P. Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor's standard commercial license. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Acknowledgments Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation.

Contents 1 Overview...4 2 User Guides for HP features for SCOM...5 3 Support Matrix...6 HP BladeSystem Management Pack (v 2.0) for System Center...6 HP ProLiant Agentless Management Pack (v 3.1) for System Center...6 HP ProLiant Linux Management Pack (v 3.1) for System Center...7 HP ProLiant PRO Management Pack (v 2.1) for System Center...8 HP ProLiant Server Management Pack (v 2.2) for System Center...8 HP ProLiant VMware Management Pack (v 3.1) for System Center...9 HP Device Monitor Console (v 1.1.2)...10 HP Device Monitor Service (v 1.1.1)...10 HP Custom Data Manager (v 1.0)...11 4 Installing and managing the HP SCOM Management Packs...12 Overview...12 Management Packs...13 HP Device Monitor Console (DMC)...13 HP Device Monitor Service (DMS)...13 Tools...14 Installing HP SCOM features...15 Installation and upgrade considerations...15 HP BladeSystem Management Pack, version 1.x...15 HP ProLiant Linux and VMware Management Pack...15 Other management packs...15 DMS, DMC, and tools...15 Installing the HP SCOM Management Packs...15 Uninstalling HP SCOM management packs...18 Repairing or modifying an HP SCOM management pack or tool...18 Upgrading from 1.x versions of HP BladeSystem Management Pack...18 Using the HP BladeSystem Migration Tool...19 5 Troubleshooting...21 Monitoring view displays multiple HP Linux Servers folders and duplicate alerts might be reported...21 Monitoring view displays multiple HP VMware Servers folders and duplicate alerts might be reported...21 Retry option in Windows 7 or in Windows Server 2008 R2 Installer does not work...21 6 Support and other resources...22 Information to collect before contacting HP...22 How to contact HP...22 Registering for software technical support and update service...22 How to use your software technical support and update service...22 Warranty information...23 HP authorized resellers...23 Related information...23 Typographic conventions...23 7 Documentation feedback...24 Glossary...25 Contents 3

1 Overview HP Insight Control for Microsoft System Center is a fully integrated product that unifies the management of physical and virtual IT environments, including servers, PCs, storage, networking devices and software. It combines an integrated set of HP extensions with Microsoft System Center to bring native manageability of HP hardware to Microsoft System Center environments. To learn more about this product, see the HP Insight Control Integrations website at: http://www.hp.com/go/icsc This guide describes the HP features for Microsoft System Center Operations Manager (SCOM). This guide is intended for use by system integrators and network administrators who are familiar with HP-branded server system products and Microsoft System Center. NOTE: This document refers to the HP Insight Control for Microsoft System Center DVD. This DVD must be created from the DVD ISO image you download from the HP Insight Control Integrations website at: https://h20392.www2.hp.com/portal/swdepot/displayproductinfo.do?productnumber=hpice 4 Overview

2 User Guides for HP features for SCOM There are separate user guides for each of the features in HP Insight Control for Microsoft System Center. For the complete set of documentation, see the Information Library at: http://www.hp.com/go/icsc/docs For each HP feature for SCOM, the following table lists the user guide that describes the feature. Table 1 HP SCOM features and user guides Feature HP BladeSystem Management Pack HP ProLiant Agentless Management Pack HP ProLiant Linux Management Pack HP ProLiant PRO Management Pack HP ProLiant Server Management Pack HP ProLiant VMware Management Pack HP Device Monitor Console (DMC) and HP Device Monitor Service (DMS) HP Custom Data Manager (CDM) User guide HP BladeSystem Management Pack (v 2.x) for Microsoft System Center User Guide HP ProLiant Agentless Management Pack (v 3.1) for Microsoft System Center User Guide HP ProLiant Linux Management Pack (v 3.1) for Microsoft System Center User Guide HP ProLiant PRO (v 2.0) Management Pack for Microsoft System Center User Guide NOTE: Pack. This guide covers versions 2.0 and 2.1 of the PRO Management HP ProLiant Server Management Pack (v 1.x & 2.2) for Microsoft System Center User Guide HP ProLiant VMware Management Pack (v 3.1) for Microsoft System Center User Guide HP Device Monitor (v 1.1) for Microsoft System Center User Guide HP ProLiant Server Management Pack (v 1.x & 2.2) for Microsoft System Center User Guide 5

3 Support Matrix This chapter provides the support matrix for each of the HP features that integrate with Microsoft System Center Operations Manager (SCOM). NOTE: HP SCOM Management Pack products are English only. However, the installation features and managed Windows servers may run other language versions of Microsoft Windows including English, French, German, Italian, Spanish, Simplified Chinese, and Japanese. HP BladeSystem Management Pack (v 2.0) for System Center Category System Center Products Operating Systems HP Insight Management Agents ProLiant Support Pack Hardware Dependencies Other Dependencies Support The SCOM environment must have one of the following Microsoft System Center products available: Operations Manager 2012 Operations Manager 2007 Operations Manager 2007 SP1 Operations Manager 2007 R2 Not applicable for managed enclosures. Not applicable. Not applicable. The following HP BladeSystem c-class enclosures are supported for management: HP BladeSystem c3000 Enclosure HP BladeSystem c7000 Enclosure HP recommends Onboard Administrator firmware version 3.60. The following management packs must be imported: HP ProLiant Server Management Pack for System Center The following HP SCOM Management Packs features must be installed in the SCOM environment: HP Device Monitor Console 1.0 or later HP Device Monitor Service 1.0 or later HP ProLiant Agentless Management Pack (v 3.1) for System Center Category System Center Products Operating Systems Support The SCOM environment must have one of the following Microsoft System Center products available: Operations Manager 2012 Operations Manager 2007 Operations Manager 2007 SP1 Operations Manager 2007 R2 Full support is provided for any ProLiant Gen8 server running the HP ProLiant Agentless Management Service (AMS). 6 Support Matrix

Category Support Limited support is provided for any bare-metal ProLiant Gen8 server or any ProLiant Gen8 server not running the AMS. Hardware Dependencies Other Dependencies Supported on ProLiant Gen8 servers. The following management packs must be imported: HP ProLiant Server Management Pack (v 2.1) for System Center or later HP Monitored ProLiant Server Library Management Pack The following HP SCOM Management Packs features must be installed in the SCOM environment: HP Device Monitor Console (v 1.1) or later HP Device Monitor Service (v 1.1) or later HP ProLiant Linux Management Pack (v 3.1) for System Center Category System Center Products Operating Systems HP Insight Management Agents Hardware Dependencies Other Dependencies Support The SCOM environment must have one of the following Microsoft System Center products available: Operations Manager 2012 Operations Manager 2007 Operations Manager 2007 SP1 Operations Manager 2007 R2 The managed computers must be running one of the following operating systems: Red Hat Enterprise Linux 5 Server x86/x64 Red Hat Enterprise Linux 6 Server x86/x64 SUSE Linux Enterprise Server 10 x86/amd64/em64t SUSE Linux Enterprise Server 11 x86/amd64/em64t NOTE: Update independent. The managed computers must have one of the following products installed, depending on the operating system: HP SNMP Agents for Red Hat Enterprise Linux 5 HP SNMP Agents for Red Hat Enterprise Linux 6 HP SNMP Agents for SUSE LINUX Enterprise Server 10 HP SNMP Agents for SUSE LINUX Enterprise Server 11 The managed computers must be HP ProLiant servers currently supported by the HP Insight Management Agents. The following management packs must be imported: HP ProLiant Server Management Pack (v 2.1) for System Center or later HP Monitored ProLiant Server Library Management Pack The following HP SCOM Management Packs features must be installed in the SCOM environment: HP Device Monitor Console (v 1.0) or later HP Device Monitor Service (v 1.0) or later HP ProLiant Linux Management Pack (v 3.1) for System Center 7

HP ProLiant PRO Management Pack (v 2.1) for System Center Category System Center Products Operating Systems ProLiant Support Pack Hardware Dependencies Other Dependencies Support The SCOM environment must have one of the following Microsoft System Center products available: Operations Manager 2007 SP1 Operations Manager 2007 R2 Also, this environment must have one of the following Microsoft System Center products available: Virtual Machine Manager 2008 Virtual Machine Manager 2008 R2 The managed computers must be running one of the following operating systems: Windows Server 2008 x64 with Hyper-V (including Server Core) Windows Server 2008 R2/SP1 with Hyper-V (including Server Core) NOTE: Update independent. The managed computers must have the following product installed from HP ProLiant Support Pack versions 8.00 through 9.10 or HP Service Pack for ProLiant versions 2012.2.0 through 2012.8.0: HP Insight Management Agents The managed computers must be HP ProLiant servers currently supported by HP Insight Management Agents. Performance and Resource Optimization (PRO) must be configured and available in Operations Manager and Virtual Machine Manager. HP ProLiant Server Management Pack (v 2.2) for System Center Category System Center Products Operating Systems Supported Agents Support The SCOM environment must have one of the following Microsoft System Center products available: Operations Manager 2012 Operations Manager 2007 Operations Manager 2007 SP1 Operations Manager 2007 R2 The managed computers must be running one of the following operating systems: Windows Server 2003 x86/x64 Windows Server 2003 R2 x86/x64 Windows Server 2008 x86/x64 (including Server Core) Windows Server 2008 R2/SP1 (including Server Core) NOTE: Update independent. The managed computers must have at least one of the following products installed from HP ProLiant Support Pack 8 Support Matrix

Category Support versions 8.00 through 9.10 or HP Service Pack for ProLiant versions 2012.2.0 through 2012.8.0: HP Insight Management Agents (required for SNMP-based management) HP Insight Management WBEM Providers (required for WMI-based management) Hardware Dependencies Other Dependencies The managed computers must be HP ProLiant servers currently supported by either HP Insight Management Agents or HP Insight Management WBEM Providers. None. HP ProLiant VMware Management Pack (v 3.1) for System Center Category System Center Products Operating Systems HP Insight Management Agents Hardware Dependencies Other Dependencies Support The SCOM environment must have one of the following Microsoft System Center products available: Operations Manager 2012 Operations Manager 2007 Operations Manager 2007 SP1 Operations Manager 2007 R2 The managed computers must be running one of the following operating systems: VMware ESX 4.0 VMware ESX 4.1 NOTE: Update independent. The managed computers must have one of the following products installed, depending on the operating system: HP Management Agents for VMware ESX 4.x The managed computers must be HP ProLiant servers currently supported by the HP Insight Management Agents. For more information on supported server models, see the ProLiant Server VMware Support Matrix at http:// h18004.www1.hp.com/products/servers/vmware/ supportmatrix/hpvmware.html The following management packs must be imported: HP ProLiant Server Management Pack (v 2.1) for System Center or later HP Monitored ProLiant Server Library Management Pack The following HP SCOM Management Packs features must be installed in the SCOM environment: HP Device Monitor Console (v 1.0) or later HP Device Monitor Service (v 1.0) or later HP ProLiant VMware Management Pack (v 3.1) for System Center 9

HP Device Monitor Console (v 1.1.2) Category System Center Products Operating Systems ProLiant Support Pack Hardware Dependencies Other Dependencies Support The SCOM environment must have one of the following Microsoft System Center products available: Operations Manager 2012 Operations Manager 2007 Operations Manager 2007 SP1 Operations Manager 2007 R2 The Operations console with HP Device Monitor Console installed must be running one of the following operating systems: Windows Server 2003 x86/x64 Windows Server 2003 R2 x86/x64 Windows Server 2008 x86/x64 Windows Server 2008 R2/SP1 Windows Vista x86/x64 Windows 7 x86/x64 NOTE: Not required. None. Update independent. The Operations console computer with HP Device Monitor Console installed must have the following installed:.net Framework 3.5 SP1 The SCOM environment must have HP Device Monitor Service installed. The Device Monitor Console must be installed on the Operations console computer to use the HP Device Monitor Console task. HP Device Monitor Service (v 1.1.1) Category System Center Products Operating Systems Support The SCOM environment must have one of the following Microsoft System Center products available: Operations Manager 2012 Operations Manager 2007 Operations Manager 2007 SP1 Operations Manager 2007 R2 The agent-managed computer with the HP Device Monitor Service installed must be running one of the following operating systems: Windows Server 2003 x86/x64 Windows Server 2003 R2 x86/x64 Windows Server 2008 x86/x64 (including Server Core) Windows Server 2008 R2/SP1 (including Server Core) NOTE: Update independent. 10 Support Matrix

Category ProLiant Support Pack Hardware Dependencies Other Dependencies Restrictions Support Not required. None. The agent-managed computer with HP Device Monitor Service installed must have the following installed:.net Framework 3.5 SP1 PowerShell 1.0 or later SNMP Trap Service 1 Version 1.1 and later versions of the Device Monitor Service require Device Monitor Console (v 1.1) or later. 1 The DMS must not be installed on a computer on which the SNMP Trap Service is disabled, such as on a computer used as a management server or gateway server for network monitoring using SCOM 2012. HP Custom Data Manager (v 1.0) Category System Center Products Operating Systems Support The SCOM environment must have one of the following Microsoft System Center products available: Operations Manager 2012 Operations Manager 2007 Operations Manager 2007 SP1 Operations Manager 2007 R2 The Operations console computer with HP Customer Data Manager installed must be running one of the following operating systems: Windows Server 2003 x86/x64 Windows Server 2003 R2 x86/x64 Windows Server 2008 x86/x64 Windows Server 2008 R2/SP1 Windows Vista x86/x64 Windows 7 x86/x64 NOTE: Update independent. ProLiant Support Pack Hardware Dependencies Other Dependencies Not required. None. The following management pack must be imported: HP ProLiant Server Management Pack for System Center The Operations console computer with HP Customer Data Manager installed must have the following installed:.net Framework 3.5 SP1 HP Custom Data Manager (v 1.0) 11

4 Installing and managing the HP SCOM Management Packs Overview The features available when you choose HP SCOM Management Packs from the HP Insight Control for Microsoft System Center installer can be installed with multiple Microsoft System Center Operations Manager (SCOM) components, including: The management server The Operations console Agent-managed computers This illustration shows the relationships between the HP installation features for SCOM and the Microsoft SCOM components. The arrows point to the SCOM components where the features can be installed. 12 Installing and managing the HP SCOM Management Packs

Management Packs The HP SCOM Management Packs feature of HP Insight Control for Microsoft System Center includes management pack files that can be imported into SCOM. This feature can be installed on the management server or on the computer that is running the Operations console. Management Pack Name Management Pack files to import 1 HP BladeSystem Management Pack for System Center HewlettPackard.Servers.BladeSystem.mp HewlettPackard.Servers.Library.mp 2 HP ProLiant Agentless Management Pack for System Center HewlettPackard.Monitored.Agentless.mp HewlettPackard.Monitored.Library.mp 2 HewlettPackard.Servers.Library.mp 2 HP ProLiant Linux Management Pack for System Center HewlettPackard.Monitored.Linux.mp HewlettPackard.Monitored.Library.mp 2 HewlettPackard.Servers.Library.mp 2 HP ProLiant PRO Management Pack for System Center HewlettPackard.Servers.ProLiant.SNMPPRO.mp HP ProLiant Server Management Pack for System Center HewlettPackard.Servers.ProLiant.SNMP.mp HewlettPackard.Servers.ProLiant.WMI.mp HewlettPackard.Servers.ProLiant.mp 2 HewlettPackard.Servers.Library.mp 2 HP ProLiant VMware Management Pack for System Center HewlettPackard.Monitored.VMware.mp HewlettPackard.Monitored.Library.mp 2 HewlettPackard.Servers.Library.mp 2 1 For a complete list of requirements, see Support Matrix (page 6). 2 This file is shared with multiple Management Packs. HP Device Monitor Console (DMC) The HP Device Monitor Console (DMC) provides the user interface for connecting to the HP Device Monitor Service (DMS) to add or remove devices supported by management packs that use the DMS. For detailed information about the DMS and the servers and enclosures it monitors, see HP Device Monitor Service (DMS) (page 13). The HP Device Monitor Console can be launched as a console task only if the DMC is installed on the computer that is running the Operations console. NOTE: The DMC and the DMS replace the HP BladeSystem Enclosure Monitor Manager (EMM), and the HP BladeSystem Enclosure Monitor Service (EMS), which were included with 1.x versions of the HP BladeSystem Management Pack. If you plan to use any management pack that uses DMS, you must upgrade from HP BladeSystem Management Pack version 1.x (from EMM and EMS to DMC and DMS). For more information about this upgrade, see Upgrading from 1.x versions of HP BladeSystem Management Pack (page 18). For detailed information about the DMC and DMS, see the HP Device Monitor for Microsoft System Center User Guide. HP Device Monitor Service (DMS) The HP Device Monitor Service (DMS) allows the devices added using the DMC to be managed with HP management packs in SCOM. The devices supported by the following management packs Overview 13

must be registered with the an instance of the DMS before they can be managed using the Operations console: HP ProLiant Agentless Management Pack HP ProLiant Linux Management Pack HP ProLiant VMware Management Pack HP BladeSystem Management Pack The DMS feature is installed on one or more agent-managed Windows servers that have been identified to perform monitoring of the devices supported by the management packs listed earlier in this section. This feature can optionally be installed on Hyper-V virtual machines. By configuring virtual machines with Windows Failover Clustering, the availability of the DMS is increased in the case of a cluster node failure. You access a DMS using the DMC, or, optionally, using PowerShell scripts provided by HP. See HP Device Monitor Console (DMC) (page 13). NOTE: The DMC and the DMS replace the HP BladeSystem Enclosure Monitor Manager (EMM), and the HP BladeSystem Enclosure Monitor Service (EMS), which were included with 1.x versions of the HP BladeSystem Management Pack. If you plan to use any management pack that uses DMS, you must upgrade from HP BladeSystem Management Pack version 1.x (from EMM and EMS to DMC and DMS). For more information about this upgrade, see Upgrading from 1.x versions of HP BladeSystem Management Pack (page 18). For detailed information about the DMC and DMS, see the HP Device Monitor for Microsoft System Center User Guide. Tools The Tools feature includes the HP Custom Data Manager (CDM). This tool can be used to store user-specified information on supported HP ProLiant servers managed by SCOM. Instructions for using the CDM are described in the HP ProLiant Server Management Pack for Microsoft System Center User Guide. The Tools feature can be installed on computers that are running the Operations console. The CDM can be launched as a console task only if the Tools feature is installed on the computer that is running the Operations console. The CDM requires the HP ProLiant Server Management Pack. NOTE: The CDM supports agent-managed HP ProLiant servers running supported versions of Windows operating system software only. 14 Installing and managing the HP SCOM Management Packs

Installing HP SCOM features Installation and upgrade considerations If you have previous versions of HP SCOM features installed on your server, read the considerations in this section before you begin the installation. IMPORTANT: HP recommends that you complete this installation at a time when the server running the software you are upgrading can be stopped, such as during a scheduled maintenance period: In rare cases, the server must be restarted at the end of the upgrade procedure. When upgrading an instance of the DMS, HP BladeSystem enclosures and servers managed by that DMS might not be available in SCOM until the upgrade process is complete and servers and enclosures managed by the DMS have been discovered and monitored. When migrating from the EMS, management for HP BladeSystem enclosures might not be available in SCOM until the migration process is complete and enclosures managed by the DMS have been discovered and monitored. Close all applications, including these applications: The Operations console (if it is installed on this computer). The DMC (if it is installed on this computer) The Windows NT event viewer PowerShell windows that are running cmdlets provided by HP HP BladeSystem Management Pack, version 1.x If a 1.x version of the HP BladeSystem Management Pack is installed, see Upgrading from 1.x versions of HP BladeSystem Management Pack (page 18) before starting this procedure. HP ProLiant Linux and VMware Management Pack Beginning with HP Insight Control for Microsoft System Center 7.0, the HP ProLiant Linux and VMware Management Pack is not supported. It has been replaced by two separate management packs: the HP ProLiant Linux Management Pack and the HP ProLiant VMware Management Pack. If you have the HP ProLiant Linux and VMware Management Pack that was included with HP Insight Control for Microsoft System Center 6.3 installed, there are extra steps to perform after you have installed and imported the management packs included with later versions of HP Insight Control for Microsoft System Center. See Step 14 (page 18). Other management packs If previous versions of other management packs are installed and imported in SCOM, these management packs are upgraded when you import the latest versions into SCOM; previously-installed management packs that have already been imported do not need to be deleted or removed. DMS, DMC, and tools If previous versions of the DMS, DMC, or tools are installed, they are upgraded automatically when you install newer versions of HP Insight Control for Microsoft System Center. When you upgrade a DMS to a newer version, information about the enclosures and servers it manages is preserved. You do not have to migrate enclosures or servers. Installing the HP SCOM Management Packs Follow this procedure to install the HP SCOM Management Packs: Installing HP SCOM features 15

1. Ensure that the prerequisites are met for the following features: Management Packs Tools This is the Management Server or this computer has the Operations console installed This computer has.net Framework 3.5 SP1 installed This computer has the Operations console installed HP Device Monitor Console This computer is one of the following: This is an agent-managed computer This computer has the Operations console installed This computer has.net Framework 3.5 SP1 installed HP Device Monitor Service This is an agent-managed Windows server This computer has.net Framework 3.5 SP1 installed This computer has SNMP Trap Service This computer has PowerShell 1.0 or greater installed 2. On the appropriate computer, log on as a user with administrator privileges. 3. Close all applications, including these applications: The Operations console (if it is installed on this computer). The DMC (if it is installed on this computer) The Windows NT event viewer PowerShell windows that are running cmdlets provided by HP 4. Insert the HP Insight Control for Microsoft System Center DVD. The welcome screen is displayed. NOTE: If the installer does not start automatically, run Autorun.exe from the DVD. 5. From the Install tab, click Install. 6. From the Installation dialog box, under Microsoft System Center Operations Manager, click HP SCOM Management Packs. 7. From the welcome screen, click Next. 8. If you are upgrading from a previous release of HP Insight Control for Microsoft System Center: a. From the Upgrade Confirmation dialog box, click Yes. b. From the Resume Installation screen, click Next. c. Skip to Step 12 (page 17). 9. From the License Agreement screen, select I accept the terms in the license agreement and click Next. 10. From the Select features to install screen, select the features to install and click Next. 16 Installing and managing the HP SCOM Management Packs

NOTE: If a feature requires a prerequisite that is missing, a dependency warning is displayed below the description of the feature, and that feature is not selectable for installation. To install a feature for which a prerequisite is missing, click Cancel to cancel the installation so that you can install the missing prerequisites. You can customize the installation path by clicking Change and specifying an installation path. 11. On the Ready to Install screen, click Install and wait for the installation to complete. 12. Click Finish to close the installer. The installation completes. The installer does not automatically import management packs into SCOM. If you have installed management packs, you import them into SCOM in the next step. 13. If you have installed the HP SCOM Management Packs feature, import the management packs into SCOM. The HP management pack files are available in the installation-path\management Packs\ folder. See Management Packs (page 13) for a list of the files to import for each management pack. NOTE: When importing management packs into SCOM, any dependent management packs that have not been installed are reported by SCOM. Installing HP SCOM features 17

14. If the HP ProLiant Linux and VMware Management Pack (HewlettPackard.Servers.Monitored.mp) is installed on this server, you must perform additional installation steps to install the management packs that replace it: a. Install and import the new management packs (including the new HP ProLiant Linux Management Pack and the HP ProLiant VMware Management Pack). b. If you configured any overrides for the HP ProLiant Linux and VMware Management Pack: i. Configure those same overrides for each of the new management packs. ii. Remove the overrides for the HP ProLiant Linux and VMware Management Pack. c. Delete the HP ProLiant Linux and VMware Management Pack for System Center from SCOM. In the Management Packs view of the Administration view, the display name for this management pack is: Hewlett-Packard ProLiant Server Management Pack for Linux and VMware version 2.0.0.0 NOTE: After you have imported either the HP ProLiant Linux Management Pack for System Center or the HP ProLiant VMware Management Pack for System Center but before you delete the HP ProLiant Linux and VMware Management Pack from SCOM, the Operations console displays multiple folders for HP Linux Servers or HP VMware servers, and duplicate alerts might be reported (see Monitoring view displays multiple HP Linux Servers folders and duplicate alerts might be reported (page 21) and Monitoring view displays multiple HP VMware Servers folders and duplicate alerts might be reported (page 21)). 15. Restart the Operations console, and the DMC and Windows NT event viewer (if needed). Uninstalling HP SCOM management packs NOTE: Uninstalling the HP SCOM Management Packs feature from the server does not delete imported management packs from SCOM. Close the DMC and delete the management packs from SCOM before you uninstall the HP SCOM Management Packs feature from the server. You can use either of these methods to uninstall HP SCOM management packs and tools: Use the Add/Remove Programs (Windows Server 2003) or Programs and Features (Windows Server 2008 and later) control panel to uninstall the HP SCOM Management Packs. Use the Remove option of the installer. Repairing or modifying an HP SCOM management pack or tool If you use the Repair option of the installer to repair a feature, the following services required by DMS might be stopped during the repair action: HP Device Monitor Service HP Common Services You must start these services when the repair is complete. If this computer has the current release of the HP SCOM Management Packs installed, you can use the Modify option of the installer to add or remove features. Upgrading from 1.x versions of HP BladeSystem Management Pack IMPORTANT: Consider completing the upgrade process during a scheduled maintenance period. HP BladeSystem enclosure management might not be available in SCOM until the upgrade process is complete and migrated enclosures have been discovered and monitored. To upgrade from a 1.x version of the HP BladeSystem Management Pack to a 2.x version: 18 Installing and managing the HP SCOM Management Packs

1. Install the HP Device Monitor Console (DMC) and HP Device Monitor Service (DMS) features (see Installing and managing the HP SCOM Management Packs (page 12)). NOTE: HP BladeSystem enclosures monitored using a previously-installed Enclosure Monitoring Service (EMS) are not available in the DMS until you migrate them in the next step. 2. Optional: Migrate HP BladeSystem enclosures monitored using the previously-installed EMS to the new DMS. The following options for enclosure migration are available: Use the DMC to add the enclosures to be migrated to the DMS manually. Adding enclosures to a DMS is described in the HP Device Monitor for Microsoft System Center User Guide. Use PowerShell cmdlets, available with the DMS, to add enclosures to be migrated to the DMS. Adding enclosures to a DMS using the available PowerShell cmdlets is described in the HP Device Monitor for Microsoft System Center User Guide. Use the migration tool included with the HP SCOM Management Packs to migrate existing data from each EMS to a local or remote DMS server. See Using the HP BladeSystem Migration Tool (page 19). 3. Install the HP SCOM Management Packs feature (described in Installing and managing the HP SCOM Management Packs (page 12)) 4. Import the 2.x version of the HP BladeSystem Management Pack into SCOM. 5. Optional: Remove the EMS by uninstalling the 1.x version of the HP BladeSystem Management Pack (listed in the control panel as HP Blade Management Pack for MS) from the computer. Do not delete the HP BladeSystem management pack from SCOM. Using the HP BladeSystem Migration Tool The HP BladeSystem Migration Tool is a command-line executable file that detects enclosures monitored by the local EMS and copies all information to the DMS you specify (local or remote). Use this tool when upgrading from a 1.x version of the HP BladeSystem Management Pack to a 2.x version. The HP BladeSystem Migration Tool must be executed using the LocalSystem account. HP recommends using the PSExec.exe tool, part of Microsoft SysInternals PS Tools, to run the migration tool using the LocalSystem account. The HPBladeMigration.exe file is in the installation-path\hp Device Monitor Service\ folder, where installation-path is the location specified in the installer when you installed the DMS. To migrate managed enclosures from the EMS to a DMS, perform the following steps for each installed EMS: 1. From the command prompt, execute the HP BladeSystem Migration Tool (HPBladeMigration.exe) using the LocalSystem account. The PSExec.exe tool must be executed using an account that has Administrator privileges. Example: C:\MyUtils>psexec -s "C:\Program Files\HP SCOM Management Packs\HP Device Monitor Service\HPBladeMigration.exe" NOTE: Enclosures monitored by the EMS may be migrated to a DMS that is installed remotely by specifying the address of the remote server and credentials for accessing the DMS. Example: C:\MyUtils>psexec -s C:\Program Files\HP SCOM Management Packs\HP Device Monitor Service\HPBladeMigration.exe -address:192.168.51.107 -username:mydomain\administrator -password:mypassword Using the HP BladeSystem Migration Tool 19

2. The BladeSystem Migration Tool lists the enclosures monitored by this EMS and asks whether to migrate the selected enclosures. To migrate the selected enclosures, enter Yes. NOTE: If you select No, the migration tool exits. The migration tool does not allow you to select individual enclosures to migrate. 3. The tool migrates the enclosures configuration information from the EMS to the DMS. When the migration is complete, the tool asks you to use the DMC to confirm that the enclosures are listed. For information about this step, see the HP Device Monitor for Microsoft System Center User Guide. TIP: Enclosure migration fails if the DMS is unable to connect to an enclosure during the migration process. Check the connection for enclosures that have not migrated successfully and attempt the migration again. This example shows sample output for the HP BladeSystem Migration Tool when migrating data from an EMS to a DMS on a different server. HP BladeSystem Migration Tool Version 1.1.0.0 Copyright (C) 2011, 2012 Hewlett-Packard Development Company, L.P. HP BladeSystem Migration Tool has detected a previous version of HP BladeSystem Monitor Service Installed on this system. The following enclosures are currently managed: 192.168.11.34 192.168.11.58 Would you like to migrate all managed enclosures to the remote HP Device Monitor Service 192.168.51.107? [Yes/No] Yes Migrating 192.168.11.34... Done [SUCCESS] Migrating 192.168.11.58... Done [SUCCESS] HP BladeSystem Migration Tool has successfully migrated 2 enclosures. Please use HP Device Monitor Console to confirm. 20 Installing and managing the HP SCOM Management Packs