Title: Improving the Performance of Jaggery Making Unit using Solar Energy. Author: Lakshmi Pathi Jakkamputi Mohan Jagadeesh Kumar Mandapati



Similar documents
Module 5: Combustion Technology. Lecture 34: Calculation of calorific value of fuels

Boiler efficiency measurement. Department of Energy Engineering

Performance of the Boiler and To Improving the Boiler Efficiency Using Cfd Modeling

EFFICIENCY WITH DIFFERENT GCV OF COAL AND EFFICIENCY IMPROVEMENT OPPORTUNITY IN BOILER

Experimental Study on Super-heated Steam Drying of Lignite

COMBUSTION. In order to operate a heat engine we need a hot source together with a cold sink

CHAPTER 7 THE SECOND LAW OF THERMODYNAMICS. Blank

Effect of Self-Heat Circulation on VOCs Decomposition in Regenerative Thermal Oxidizer

Drying of Woody Biomass. Process Engineering / GEA Barr-Rosin

COMPARISON OF PROCESS FLOWS: FLUID BED COMBUSTOR AND GLASSPACK

Building Energy Systems. - HVAC: Heating, Distribution -

Boiler Calculations. Helsinki University of Technology Department of Mechanical Engineering. Sebastian Teir, Antto Kulla

Module 5: Combustion Technology. Lecture 33: Combustion air calculation

1.3 Properties of Coal

A Method for Calculating Thermal Efficiency Of the Solid Fuel Fired Boiler Zetao Wang1,a, Yujiao Gong2,b,Xuedong Jing1, c *

Optimising Glass Melting Processes with Energy & Mass Balance Calculations

Webpage: Volume 3, Issue IV, April 2015 ISSN

5. State the function of pulveriser. The pulverisers are the equipments which are used to powdered coal.

Calculate Available Heat for Natural Gas Fuel For Industrial Heating Equipment and Boilers

OUTCOME 2 INTERNAL COMBUSTION ENGINE PERFORMANCE. TUTORIAL No. 5 PERFORMANCE CHARACTERISTICS

Assignment 8: Comparison of gasification, pyrolysis and combustion

PRESENTER: Yusuf Abdul General Manager- Technical Services. Guyana Sugar Corporation Inc. Ogle, East Coast Demerara GUYANA

Half the cost Half the carbon

Waste Heat Recovery through Air Conditioning System

THE PRODUCTION OF ELECTRICITY FROM WOOD AND OTHER SOLID BIOMASS

THE PSYCHROMETRIC CHART: Theory and Application. Perry Peralta NC State University

Chapter 2.2: Boilers

HYBRID WAY EAF OFF GAS HEAT RECOVERY -ECORECS- MASANARI YAMAZAKI*1, YASUHIRO SATO*2, RYUTARO SEKI*3

A Demonstration Plant of a Liquid Desiccant Air Conditioning Unit for Drying Applications

Stora Enso Fors Ltd Sweden

Evaluation of mobile storage systems for heat transport. G. Storch, A. Hauer, A. Krönauer ZAE Bayern, Walther-Meißner-Str. 6, Garching, Germany

Performance Analysis of Thermal Power Station: Case Study of Egbin Power Station, Nigeria

Recover Heat from Boiler Blowdown Water

Air-sourced 90 Hot Water Supplying Heat Pump "HEM-90A"

Steam Generator Boilers Compact Steam Boilers. Rapid Start-Up Safe in Operation

Performance Test of Solar Assisted Solid Desiccant Dryer

CONTENTS. ZVU Engineering a.s., Member of ZVU Group, WASTE HEAT BOILERS Page 2

APPLIED THERMODYNAMICS. TUTORIAL No.3 GAS TURBINE POWER CYCLES. Revise gas expansions in turbines. Study the Joule cycle with friction.

Chapter 18 Temperature, Heat, and the First Law of Thermodynamics. Problems: 8, 11, 13, 17, 21, 27, 29, 37, 39, 41, 47, 51, 57

Analysis of Jaggery. What is Jaggery? Composition of Cane Jaggery

An analysis of a thermal power plant working on a Rankine cycle: A theoretical investigation

where V is the velocity of the system relative to the environment.

Modelling the Drying of Porous Coal Particles in Superheated Steam

Thermal efficiency of pulverized fuel boiler

1. A belt pulley is 3 ft. in diameter and rotates at 250 rpm. The belt which is 5 ins. wide makes an angle of contact of 190 over the pulley.

Environment Impact Assessment of Thermal Power Plant for Sustainable Development

5 Answers and Solutions to Text Problems

COKE PRODUCTION FOR BLAST FURNACE IRONMAKING

How To Power A Power Plant With Waste Heat

Forgotten savings: Heat recovery from surface blowdown

steam centre of excellence Steam Boiler System Optimization

The soot and scale problems

BOILERS, BOILER FUEL AND BOILER EFFICIENCY

Estimated emissions and CO2 savings deriving from adoption of in-place recycling techniques for road pavements

SIX REASONS TO DRY BIOGAS To A LOW DEWPOINT BEFORE COMBUSTION IN A CHP ENGINE STEVEN SCOTT MARKET DEVELOPMENT MANAGER ALTERNATIVE ENERGIES

OPPORTUNITIES FOR HEAT RATE REDUCTIONS IN EXISTING COAL- FIRED POWER PLANTS: A STRATEGY TO REDUCE CARBON CAPTURE COSTS

Overview of Integrated Coal Gasification Combined-cycle Technology Using Low-rank Coal

Condensing Economizers Workshop Enbridge Gas, Toronto. MENEX Boiler Plant Heat Recovery Technologies. Prepared by: Jozo Martinovic, M A Sc, P Eng

Exergy: the quality of energy N. Woudstra

HEAT RECOVERY OPTIONS FOR DRYERS AND OXIDIZERS

1. ENERGY PERFORMANCE ASSESSMENT OF BOILERS

HEAT TRANSFER IM LECTURE HOURS PER WEEK THERMODYNAMICS - IM _1

New technical solutions for energy efficient buildings

Dharam V. Punwani President, Avalon Consulting, Inc. Presented at Turbine Inlet Cooling Association Webinar April 9, 2014

Extracting Valuable Lignin for Biorefinary Production and Replacement of Fossil Fuels

Note: You will receive no credit for late submissions. To learn more, read your instructor's Grading Policy

Continuous flow direct water heating for potable hot water

Type: Single Date: Homework: READ 12.8, Do CONCEPT Q. # (14) Do PROBLEMS (40, 52, 81) Ch. 12

Comparing Air Cooler Ratings Part 1: Not All Rating Methods are Created Equal

Evaluation Of Hybrid Air- Cooled Flash/Binary Power Cycle

Use of Substitute Fuels in Large Combustion Plants (LCPs)

C H A P T E R T W O. Fundamentals of Steam Power

ANALYSIS OF ENERGY SAVING OPPORTUNITIES IN CEMENT SECTOR

ENGINEERING INFORMATION Hot water and steam service

A Review on Power Generation in Thermal Power Plant for Maximum Efficiency

Station #1 Interpreting Infographs

Availability. Second Law Analysis of Systems. Reading Problems , 10.65, 10.66, , 10.75, 10.81, 10.

INTERNATIONAL JOURNAL OF INNOVATIVE RESEARCH IN ELECTRICAL, ELECTRONICS, INSTRUMENTATION AND CONTROL ENGINEERING

Increasing Natural Gas Boiler Efficiency by Capturing Waste Energy from Flue Gas

4 th EU Sout Africa Clean Coal Working Group Meeting

Modern Sand Reclamation Technologies for Economy, Environment Friendliness and Energy Efficiency

How To Run A Power Plant In Celje

Biomass Boiler House Best Practices. Irene Coyle & Fernando Preto CanmetENERGY

Carbon Dioxide Membrane Separation for Carbon Capture using Direct FuelCell Systems

Green Building Handbook for South Africa Chapter: Heating, Ventilation and Cooling Luke Osburn CSIR Built Environment

Basics of Steam Generation

Study on performance and methods to optimize thermal oil boiler efficiency in cement industry

IMPROVING THE EFFICIENCY OF THERMAL EQUIPMENTS OF 210 MW TPS THROUGH THERMAL AUDIT

Renewable vs. non-renewable energy sources, forms and technologies prepared by. A.Gritsevskyi, IAEA

6 18 A steam power plant receives heat from a furnace at a rate of 280 GJ/h. Heat losses to the surrounding air from the steam as it passes through

Efficiency on a large scale CFB Steam Boilers

COAL, OIL SHALE, NATURAL BITUMEN, HEAVY OIL AND PEAT Vol. II -Extraction of Oil Shale: Surface and In Situ Retorting - Victor Yefimov and Shuyuan Li

Exam on Heat and Energy

Numerical analysis of size reduction of municipal solid waste particles on the traveling grate of a waste-to-energy combustion chamber

Physics and Economy of Energy Storage

Diesel Cycle Analysis

Fundamentals of Climate Change (PCC 587): Water Vapor

Lesson 36 Selection Of Air Conditioning Systems

Transcription:

Title: Improvg the Performance of Jaggery Makg Unit usg Solar Energy Author: Lakshmi Pathi Jakkamputi Mohan Jagadeesh Kumar Mandapati PII: S2213-0209(16)30033-7 DOI: http://dx.doi.org/doi:10.1016/j.pisc.2016.04.019 Reference: PISC 181 To appear : Received date: 7-1-2016 Accepted date: 5-4-2016 Please cite this article as: Jakkamputi, L.P., Mandapati, M.J.K.,Improvg the Performance of Jaggery Makg Unit usg Solar Energy, Perspectives Science (2016), http://dx.doi.org/10.1016/j.pisc.2016.04.019 This is a PDF file of an unedited manuscript that has been accepted for publication. As a service to our customers we are providg this early version of the manuscript. The manuscript will undergo copyeditg, typesettg, and review of the resultg proof before it is published its fal form. Please note that durg the production process errors may be discovered which could affect the content, and all legal disclaimers that apply to the journal perta.

Improvg the Performance of Jaggery Makg Unit usg Solar Energy Lakshmi Pathi Jakkamputi a, Mohan Jagadeesh Kumar Mandapati b* School of Mechanical Engeerg, VIT University, Vellore, Tamilnadu India Abstract The thermal performance of open earth pan furnace used conventionally for preparg jaggery (gur) is very low. Dry bagasse is used as a fuel to produce heat a combustion process the open earth furnace. The energy loss due to efficient combustion process, the energy loss through exhaust gases and other losses due to furnace wall, convection and radiation brg the thermal efficiency of open earth pan furnace to a low value. Certa quantity of energy produced combustion process is used to sensibly heat the sugarcane juice to its evaporation temperature. Solar collectors can supply the sensible heat required to raise the sugarcane juice temperature up to its boilg pot, thereby reducg the total quantity of heat required preparg the Jaggery. Solar drier can be used to supply hot air required for the combustion process to burn the bagasse more efficient manner. This paper presents analytical calculations done to study the performance improvement of the jaggery makg unit usg solar collector and solar drier. Keywords: Bugasse, Heat transfer, Jaggery, Solar energy, Sugarcane. Special Issue- ICEMS-2016 * Correspondg author. Tel: +91-8056903625 E-mail: mohan.jagadeeshkumar@vit.ac. (or) mmjk.iitkgp@gmail.com Page 1 of 7

1. Introduction Jaggery prepared conventionally open earth pan furnaces has been used as a sweetener many places of India from ancient times. Sugarcane juice and bagasse extracted after crushg sugarcane are used as the raw materials to prepare jaggery. Out of total sugarcane annually produced India, around 2/3 rd is used to produce sugar, 1/5 th used to produce jaggery and remag is used for other commercial purposes [1]. The preparation of jaggery is considered as a small scale dustry, givg employment to many formers rural India. Jaggery contas 65-85% of sucrose, 10-15% of reducg sugars, 3-10% of moisture, and the remag is soluble matter [2]. Mechanical and thermal energies are required to prepare jaggery usg open earth pan furnace. Mechanical energy is required to crush the sugarcane to produce sugarcane juice, and thermal energy is required to heat the sugarcane juice to prepare jaggery the furnace. Crushg the sugarcane will produce sugarcane juice and bagasse as a by-product. At the itial moment the moisture content the bagasse is around 40-50% [3]. The moisture content can be reduced to 8-10% by dryg the bagasse open area, and then dry bagasse is used as a raw material to produce heat by combustion the open earth furnace. It was observed that out of the total energy produced the combustion process, around 45% is used for jaggery preparation and remag is lost through flue gases, ash and furnace walls. Sugarcane juice used preparation of jaggery the open earth pan consists of three different stages. The first stage of process begs with supplyg sensible heat (around 6% of total energy produced the combustion process) required to raise the temperature of sugarcane juice from ambient to its boilg pot. Measured quantity of additives like bendi, calcium carbonate and phosphoric acid (each at around 30-50 gm/100 kg of sugarcane) will be added to the sugarcane juice to mata the required ph this stage [4]. The second stage consists of removal of water from the sugarcane juice at its saturation/boilg temperature. The amount of heat supplied durg this stage (around 39% of the total energy produced the combustion process) is considered to be latent of vaporization required to convert water to steam. Floatg residue known as molasses (around 3 to 5 kg/390 kg of sugarcane juice) is formed at this pot and needs to be removed from the free surface. At the end of the second stage, the sugarcane juice will become rich concentrated solids as the water is completely removed. In the last stage of jaggery preparation, the heat supplied (around 0.1% of the total energy produced) is utilized to crease the temperature of the sugarcane juice from its boilg pot to strikg pot. The strikg pot is the temperature at which the sugarcane juice converts to a semisolid paste which slides on the pan surface stead of stickg to the pan. At this stage the sugarcane juice semi-solid state is removed from the pan and cooled to room temperature to prepare the jaggery. The conventional process of jaggery preparation is represented Fig. 1. Fig. 1 Conventional process of jaggery preparation This paper discusses the use of solar energy the supply of partial or full amount of the heat required the first and second stages of jaggery preparation. Combustion efficiency of the open earth furnace can be creased by usg preheated air place of atmospheric air and bagasse with low moisture content at the let to the furnace. Solar collectors and solar Page 2 of 7

driers can be used as a source of heat the jaggery preparation. Sugarcane juice can be heated to its boilg temperature usg solar collectors and then send to the boilg pan for jaggery preparation. Solar drier can be used to preheat the air supplied to the furnace and remove the moisture content from the bagasse which enhances the combustion efficiency. The suggested modified process of jaggery preparation with solar energy as a heat source is shown Fig. 2. 2. Mathematical Modellg Fig. 2 Modified process of jaggery preparation with solar energy Applyg conservation of mass, Eq. (1) is used to write mass balance between various puts and outputs to the Jaggery preparation unit. m m m m t (1) out gen For a steady state operation and assumg there is no mass generation Eq. (1) can be modified as, m m 0 (2) out In Eq. (2), m and m out are the total mass flow rate and out to the production unit. The various mass quantities supplied to the production unit are mass of sugarcane juice, additives, dry bagasse and combustion air. The various mass quantities produced from the production unit are mass of jaggery, floatg residue, steam, flue gas and ash. Along the combustion le and sugar cane to jaggery preparation le the mass conservation results, m m m m (3) db da fg ash m m m m m (4) sj add jag fr st In Eq. (3), m db, m da are the mass flow rates of dry bagasse and dry air supplied for combustion. m fg and m ash flow rates of flue gases and ash produced the combustion. In Eq. (4), m, sj m add are the mass are the mass flow rates of sugarcane juice and additives, m sj mass flow rate of jaggery produced, m fr mass flow rate of floatg residue and m st is the mass flow rate of steam produced due to evaporation of water the sugarcane juice. Applyg conservation of energy, Eq. (5) is used to write energy balance between various puts and outputs to the jaggery preparation unit. E E E E t (5) out gen Assumg that there is no addition to energy generation and that the process of energy transfer is a steady state process, Eq. (5) can be written as, E E out 0 (6) In Eq. (6), E rate of energy put to the production unit and equal to the heat produced by burng dry bagasse the furnace is given by, E m CV db db In Eq. (7), CV db is the calorific value of dry bagasse can be calculated with the Eq. (8) available [5]. CV 18260 207.1 182.06 37.1 (8) 1 2 3 db (7) Page 3 of 7

In Eq. (8), 1 is the moisture content kg/kg of dry bagasse, 2 the ash content kg/kg of dry bagasse and 3 is the sugar content of the bagasse. In Eq. (6), E is the rate of energy comg out from the production unit and is equal to the sum of heat used by the out sugarcane juice to raise its temperature from itial temperature to its boilg temperature, E, heat used to convert water sugarcane juice to steam, E st, heat used to raise the temperature of the sugarcane juice from its boilg pot to strikg pot, E str and heat lost through flue gases, wall, ash and un burnt fuel. E E E E E E E E (9) out sj st str fg ash uf w In Eq. (9), E fg is the energy lost through flue gases, E w the energy lost to the walls, E ash the energy lost through the ash and E uf is the energy lost through the un burnt fuel. The various quantities Eq. (9) are calculated usg the followg equations given Eq. (10) to Eq. (12). E m C T T, E m h, E m C T T (10), sj sj sj bsj isj st st fgst str j j str b E m C T T E m C T T (11) fg fg fg fg amb ash ash ash ash amb E E E E (12) w w cond w conv w rad It is proposed to reduce the sensible heat required for sugarcane to raise its temperature up to its boilg pot and the heat lost through flue gases by usg solar energy. Then E sj and E fg are modified as, E m C T T, E m C T T (13) sj sj sj bsj isj fg fg fg fg ia The let temperature of the sugarcane juice, T isj, to the pan and let temperature of the air to the combustion chamber of the furnace, T ia, can be creased by usg solar energy. Then the amount of bagasse used for jaggery preparation plant will be reduced as the magnitudes of E and E are reduced. 3. Results and Discussion sj fg Analytical calculations were done to show the effect of let temperature of sugarcane juice and let temperature air on the performance of the jaggery preparation plant. Calculations were made to fd the performance of the plant on the basis of unit jaggery produced by usg (7) to (13). The followg assumptions were made for the analytical calculations. About 2.39 kg of dry bagasse is required to produce 1 kg of jaggery. Mass of dry bagasse produced is about 20% of the sugarcane crushed. Mass of sugarcane juice produced is about 65% of the sugarcane crushed. Calorific value of dry bagasse is 16,230 kj/kg. Mass of additives (calcium carbonate, phosphoric acid and okra) to the sugarcane juice is each 0.5 g per kg of sugarcane juice. Mass of floatg residue (molasses) produced is 10.25 g per kg of sugarcane juice. Air fuel ratio the combustion process is 5.4 [6]. Specific heat of flue gases is approximately equal to the specific heat of air. Inlet temperature of sugarcane juice and let temperature of air to the furnace were considered to be the variable parameters. Energy distribution for various quantities per kg of jaggery production is calculated. They are, E (given by Eq. (7)) = 38789.7 kj; E sj (given by Eq. (10)) = 2360.44 kj; E st (given by Eq. (10)) = 15212.33 kj; sj E str (given by Eq. (10)) = 30 kj; fg E (given by Eq. (11)) = 14990.08 kj; unaccounted E = 6638.87 kj. Variation of sensible heat required to heat the sugarcane juice from its let temperature to boilg temperature, E sj, with different sugarcane juice let temperatures, T isj, is presented Fig. 3. The value of E sj is changed from 2360.44 kj/kg of jaggery to 295.05 kj/kg of jaggery as T isj changed from 20 o C to 90 o C. It is a clear dication that we can save the amount of heat required (about 2360 kj/kg of jaggery) to prepare the jaggery by sendg the sugarcane juice at higher let temperature to the open earth pan. Page 4 of 7

Fig. 3 Variation of sensible heat required to raise the sugarcane temperature from let value to its boilg pot with let temperature of sugarcane juice The variation of sensible heat energy, E sj, saved when the let temperature of sugarcane juice is changed from 30 o C to 100 o C with that when the let temperature is 20 o C is shown Fig. 4. The variation of dry bagasse saved as the temperature of let temperature of sugarcane is changed from 20 o C to 100 o C is also shown Fig. 4. It can be found from Fig. 4 that the amount of dry bagasse which can be saved is creased from 0.02951 kg to 0.23604 kg per kg of jaggery preparation. The dry bagasse can be used as an alternative fuel and raw product for paper and pulp dustry. Any savgs dry bagasse consumption the jaggery preparation will add revenue to the farmers. Fig. 4 Variation of Dry Bagasse saved and Sensible heat saved to raise the sugarcane temperature from let value to its boilg pot with let temperature of sugarcane juice Similarly variations the heat lost through flue gases, E fg, for different air let temperature, T ia, are presented Fig. 5. The amount of E fg was observed to be changg from 14990.08 kj/kg of jaggery to 13001.60 kj/kg of jaggery as the air let temperature to the open earth furnace changed from 20 o C to 150 o C. The amount of heat lost can be mimized through flue gases which crease the performance of the jaggery preparation cycle. Fig. 5 Variation of heat lost through the flue gases with let temperature of air to the furnace The amount of E fg, saved when the let temperature of sugarcane juice is changed from 30 o C to 150 o C with that when the let temperature is 20 o C is shown Fig. 6. The variation of dry bagasse saved as the air let temperature is changed Page 5 of 7

from 20 o C to 100 o C is also shown Fig. 6. It can be found from Fig. 6 that the amount of dry bagasse which can be saved is creased from 0.00942 kg to 0.12252 kg per kg of jaggery preparation. The extent to which either the sugarcane juice or let air is preheated will be dependent on the performance of solar collector or solar drier. If the sugarcane juice is preheated close to its boilg temperature then there will be a maximum percentage ga the dry bagasse saved. Similarly, if the air let temperature is more that 120 o C then the ga the dry bagasse saved is higher. Fig. 6 Variation of Dry Bagasse saved and heat energy saved through the flue gases with let temperature of air to the furnace 4. Conclusion In the conventional process of jaggery preparation, dry bagasse is used as raw material for the combustion process. Around 45% of total energy produced the combustion process is effectively utilized for jaggery preparation and remag 55% of total energy is lost through flue gases, ash and walls. Major amount of energy around 39.22 % is required to remove water from the sugarcane juice. Around 6.08 % is used as a sensible heat to raise the sugarcane juice temperature from its itial value to its boilg temperature, and 0.1% is used to raise the sugarcane juice temperature from its boilg temperature to its strikg pot. If the sugarcane juice was preheated close to its boilg temperature it was found that around 2360.44 kj of heat energy and 0.23604 kg of dry bagasse could be saved per kg of jaggery preparation. If the air let temperature is creased up to 150 o C it was found that around 1988.48 kj of heat energy and 0.12252 kg of dry bagasse can be saved per kg of jaggery preparation. To preheat the sugarcane juice or let air we can utilize the solar energy or any dustrial waste heat available. The amount of heat energy and dry bagasse saved will crease if we supply the complete or partial amount of latent of heat to remove water from the sugarcane juice usg solar energy or dustrial waste heat. References [1] S. I. Anwar, Fuel and Energy Savg Open Pan Furnace Used Jaggery Makg Through Modified Juice Boilg/Concentratg Pans, Energy Conversion and Management, 51, 2010, pp. 360-364. [2] J. P. V. K. Rao, M. Das, and S. K. Das, Jaggery a traditional Indian sweetener, Indian Journal of Traditional Knowledge, 6, no. 1, 2007, pp. 95-102. [3] P. J. Manohar Rao, Industrial utilization of sugar and its by products, New Delhi, India: ISPCK Publishers and Distributors, 1977. [4] A. K. Ghosh, A. K. Shrivastava, and V. Agnihotri, Production technology of lump sugar-gur/jaggery, New Delhi, India: Daya Publishg House, 1998. [5] S. S. Munsamy, Optimizg Bagasse Dewaterg a Cane Diffuser at Sezela Sugar Factory, Proceedgs of South Africa Sugar Technology Association, 8, 2008, pp. 154-159. Page 6 of 7

[6] Kiran Y. Shiralkar, Sravan K. Kancharla, Narendra G. Shah, Sanjay M. Mahjani, Energy Improvements Jaggery Makg Process, Energy for Sustaable Development, 18, 2014, pp. 36-48. Page 7 of 7