(Photo: CDX-GT130) SPECIFICATIONS

SERVICE MANUAL Ver. 1.0 2008.08 CDX-GT130/GT180/GT230/ GT280/GT280S/GT282S US Model CDX-GT130 Canadian Model CDX-GT230 E Model CDX-GT180/GT280/GT280S/GT282S (Photo: CDX-GT130) The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism CD Drive Mechanism Type Optical Pick-up Name CDX-GT33W/GT330 MG-101L-188//C DAX-25A SPECIFICATIONS CD player section Signal-to-noise ratio: 120 db Frequency response: 10 20,000 Hz Wow and flutter: Below measurable limit Tuner section FM Tuning range: CDX-GT130/GT230: 87.5 107.9 MHz CDX-GT180/GT280/GT280S/GT282S: 87.5 108.0 MHz (at 50 khz step) 87.5 107.9 MHz (at 200 khz step) FM tuning interval: CDX-GT180/GT280/GT280S/GT282S: 50 khz/200 khz switchable Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: 150 khz Usable sensitivity: 10 dbf Selectivity: 75 db at 400 khz Signal-to-noise ratio: 70 db (mono) Separation: 40 db at 1 khz Frequency response: 20 15,000 Hz MW (CDX-GT180/GT280/GT280S/GT282S) Tuning range: 531 1,602 khz (at 9 khz step) 530 1,710 khz (at 10 khz step) MW tuning interval: 9 khz/10 khz switchable Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: 25 khz Selectivity: 26 μv SW (CDX-GT180/GT280/GT280S/GT282S) Tuning range: SW1: 2,940 7,735 khz SW2: 9,500 18,135 khz (except for 10,140 11,575 khz) Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: 25 khz Selectivity: 30 μv Power amplifier section Outputs: Speaker outputs (sure seal connectors) Speaker impedance: 4 8 ohms Maximum power output: 52 W 4 (at 4 ohms) General Outputs: Audio outputs terminal (sub/rear switchable) Power antenna (aerial) relay control terminal Power amplifier control terminal Inputs: Antenna (aerial) input terminal AUX input jack (stereo mini jack) Tone controls: Low: ±10 db at 60 Hz (XPLOD) Mid: ±10 db at 1 khz (XPLOD) High: ±10 db at 10 khz (XPLOD) Power requirements: 12 V DC car battery (negative ground (earth)) Power supply voltage: 11 16 V Continued on next page AM (CDX-GT130/GT230) Tuning range: 530 1,710 khz Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: 25 khz Sensitivity: 26 μv CDX-GT130/GT230 FM/AM COMPACT DISC PLAYER CDX-GT180/GT280/GT280S/GT282S FM/MW/SW COMPACT DISC PLAYER 9-889-234-01 2008H04-1 2008.08 Sony Corporation Audio&Video Business Group Published by Sony Techno Create Corporation

Dimensions: Approx. 178 50 179 mm (7 1 /8 2 7 1 /8 in.) (w/h/d) Mounting dimensions: Approx. 182 53 162 mm (7 1 /4 2 1 /8 6 1 /2 in.) (w/h/d) Mass: Approx. 1.2 kg (2 lb 11 oz) Supplied accessories: Card remote commander: CDX-GT230/GT280/GT280S/GT282S: RM-X151 Parts for installation and connections (1 set) Design and specifications are subject to change without notice. MODEL IDENTIFICATION The CDX-GT180, CDX-GT230, CDX-GT280 and CDX280S include the model manufactured in Chinese and the model manufactured in Thai. This service manual guides the model manufactured in Chinese. Check the part number specified on the model number label when performing service and inspection. Bottom View NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. NOTES ON CHIP COMPONENT REPLACEMENT Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. TEST DISCS Please use the following test discs for the check on the CD section. YDES-18 (Part No. 3-702-101-01) PATD-012 (Part No. 4-225-203-01) CD Play back You can play CD-DA (also containing CD TEXT) and CD- R/CD-RW (MP3/WMA files). FRONT PANEL Part.No. Type of disc Label on the disc Model Part No. CDX-GT130: US 4-000-325-0[] CDX-GT180: E 4-106-962-0[] 4-106-963-0[] CDX-GT230: CND 4-106-939-0[] CDX-GT280: E 4-106-837-0[] 4-106-904-0[] CDX-GT280: MX 4-106-910-0[] CDX-GT280S: E 4-106-915-0[] 4-106-935-0[] CDX-GT282S: IND 4-106-937-0[] CD-DA MP3* WMA* * CDX-GT230/GT280/GT280S/GT282S only Abbreviation CND : Canadian model MX : Mexican model IND : Indian model SAFETY-RELATED COMPONET WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC- TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON- NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. 2

CAUTION Use of controls or adjustments or performance of procedures other than those specifi ed herein may result in hazardous radiation exposure. If the optical pick-up block is defective, please replace the whole optical pick-up block. Never turn the semi-fixed resistor located at the side of optical pick-up block. optical pick-up semi-fixed resistor CDX-GT180/GT280/GT280S/GT282S: This compact disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the exterior. TABLE OF CONTENTS 1. SERVICING NOTES... 4 2. GENERAL Location of Controls... 5 Connections... 6 3. DISASSEMBLY 3-1. Sub Panel Assy... 9 3-2. CD Mechanism Block... 9 3-3. Main Board... 10 3-4. Servo Board... 10 3-5. Chassis (T) Sub Assy... 11 3-6. Roller Arm Assy... 11 3-7. Chassis (OP) Assy... 12 3-8. Chucking Arm Sub Assy... 12 3-9. Sled Motor Assy... 13 3-10. Optical Pick-up Section... 14 3-11. Optical Pick-up... 14 4. DIAGRAMS 4-1. Block Diagram Main Section... 15 4-2. Block Diagram Display Section... 16 4-3. Printed Wiring Board Main Section... 17 4-4. Schematic Diagram Main Section (1/3)... 18 4-5. Schematic Diagram Main Section (2/3)... 19 4-6. Schematic Diagram Main Section (3/3)... 20 4-7. Printed Wiring Boards Key Section... 21 4-8. Schematic Diagram Key Section... 22 5. EXPLODED VIEWS 5-1. Main Section... 28 5-2. Front Panel Section... 29 5-3. CD Mechanism Section (MG-101L-188//C)... 30 6. ELECTRICAL PARTS LIST... 31 This label is located on the bottom of the chassis. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40 C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. 3

SECTION 1 SERVICE NOTE EXTENSION CABLE AND SERVICE POSITION When repairing or servicing this set, connect the jig (extension cable) as shown below. Connect the MAIN board (CNP301) and the SERVO board (CN401) with the extension cable (Part No. J-2502-076-1). MAIN board CNP301 J-2502-076-1 SERVO board CN401 NOTE FOR REPLACEMENT OF THE AUX JACK (J901) To replace the AUX jack requires alignment. 1. Insert the AUX jack into the KEY board. 2. Place the KEY board on the front panel. 3. Solder the three terminals of the jack. KEY board NOTE FOR REPLACEMENT OF THE SERVO BOARD When repairing, the complete SERVO board (A-1542-217-A) should be replaced since any parts in the SERVO board cannot be repaired. NOTE FOR THE 15-PIN CONNECTOR (CN901) Do not use alcohol to clean the 15-pin connector (CN901) connecting the front panel with the main body. Do not touch the connector directly with your bare hand. Poor contact may be caused. AUX jack front panel 4

LOCATION OF CONTROLS CDX-GT130/GT230: CDX-GT130/GT180/GT230/GT280/GT280S/GT282S SECTION 2 GENERAL This section is extracted from instruction manual. Location of controls and basic operations 6 Main unit OFF SEEK DSPL SEEK SOURCE EQ3 MODE PUSH SELECT BTM Card remote commander RM-X151 (CDX-GT330/GT33W/GT230 only) OFF SOURCE DSPL SEL + ATT MODE SCRL 1 2 3 4 5 6 + VOL AF TA TP REG DISC ALBM ARTIST TRACK SHUF ZAP DM+ LOUD REP SHUF PAUSE 1 2 3 4 5 6 This section contains instructions on the location of controls and basic operations. For details, see the respective pages. For optional device (CD changer, etc.,) operation, see CD changer (CDX-GT330/ GT33W only) on page 11. The corresponding buttons on the card remote commander control the same functions as those on the unit. OFF button To power off; stop the source. SEEK +/ buttons CD: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fastforward a track (press and hold). Radio: To tune in stations automatically (press); find a station manually (press and hold). SOURCE button To power on; change the source* (Radio/CD/ AUX). EQ3 (equalizer) button page 9 To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF). Control dial/select button page 9 To adjust volume (rotate); select setup items (press and rotate). Disc slot Insert the disc (label side up), playback starts. Display window AUX AUX input jack page 10 To connect a portable audio device. (eject) button To eject the disc. DSPL (display)/scrl (scroll) button (CDX-GT330/GT33W/GT230) page 8 To change display items (press); scroll the display item (press and hold). DSPL (display) button (CDX-GT130) page 8 To change display items. (front panel release) button page 5 MODE button page 8 To select the radio band (FM/AM)*. BTM/CAT button (CDX-GT330/GT33W) page 8 To start the BTM function (press and hold). BTM button (CDX-GT130/GT230) page 8 To start the BTM function (press and hold). RESET button (located behind the front panel) (CDX-GT330/GT33W only) page 4 Number buttons CD: /: ALBUM /+ (during MP3/WMA playback) (CDX-GT330/GT33W/GT230) To skip albums (press); skip albums continuously (press and hold). : REP page 8 : SHUF page 8 : PAUSE To pause playback. To cancel, press again. Radio: To receive stored stations (press); store stations (press and hold). Receptor for the card remote commander (CDX-GT330/GT33W/ GT230 only) The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (page 4) (CDX-GT330/GT33W/GT230 only). ()/ () buttons To control CD/radio, the same as /+ on the unit. Setup, sound setting, etc., can be operated by. DSPL (display) button To change display items. VOL (volume) +/ button To adjust volume. ATT (attenuate) button To attenuate the sound. To cancel, press again. SEL (select) button The same as the select button on the unit. (+)/ ( ) buttons To control CD, the same as / (ALBUM /+) on the unit. Setup, sound setting, etc., can be operated by. SCRL (scroll) button To scroll the display item. Number buttons To receive stored stations (press); store stations (press and hold). * In the case of a CD changer, HD Radio tuner or SAT tuner being connected; when is pressed, the connected device ( HD, XM or SR ) will appear in the display, depending on which device is connected. Furthermore, if is pressed, you can switch the changer, HD Radio tuner band or SAT tuner band (CDX-GT330/GT33W only). Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless on the unit is pressed, or a disc is inserted to activate the unit first. 7 CDX-GT180/GT280/GT280S/GT282S: Location of controls and basic operations Main unit OFF SEEK DSPL SEEK SOURCE EQ3 MODE PUSH SELECT BTM Card remote commander RM-X151 (CDX-GT282S/ GT280S/GT280/GT28M only) OFF SOURCE DSPL SEL + ATT MODE SCRL 1 2 3 4 5 6 + VOL LOUD SET UP DISC ALBM TRACK PTY ST SHUF AF TA TP REG REP SHUF PAUSE 1 2 3 4 5 6 This section contains instructions on the location of controls and basic operations. For details, see the respective pages. The corresponding buttons on the card remote commander control the same functions as those on the unit. OFF button To power off; stop the source. SEEK +/ buttons CD: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fastforward a track (press and hold). Radio: To tune in stations automatically (press); find a station manually (press and hold). SOURCE button To power on; change the source (Radio/CD/ AUX). EQ3 (equalizer) button page 9 To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF). Control dial/select button page 9 To adjust volume (rotate); select setup items (press and rotate). Disc slot Insert the disc (label side up), playback starts. Display window AUX AUX input jack page 10 To connect a portable audio device. (eject) button To eject the disc. DSPL (display)/scrl (scroll) button (CDX-GT282S/GT280S/GT280/GT28M) page 8 To change display items (press); scroll the display item (press and hold). DSPL (display) button (CDX-GT180) page 8 To change display items. (front panel release) button page 5 MODE button page 8 To select the radio band (FM/MW/SW). BTM button page 8 To start the BTM function (press and hold). Frequency select switch (located on the bottom of the unit) See Frequency select switch in the supplied installation/connections manual. Number buttons CD: /: ALBUM /+ (during MP3/WMA playback) (CDX-GT282S/GT280S/ GT280/GT28M) To skip albums (press); skip albums continuously (press and hold). : REP page 8 : SHUF page 8 : PAUSE To pause playback. To cancel, press again. Radio: To receive stored stations (press); store stations (press and hold). Receptor for the card remote commander (CDX-GT282S/GT280S/ GT280/GT28M only) The following buttons on the card remote commander have also different buttons/functions from the unit. Remove the insulation film before use (page 5) (CDX-GT282S/GT280S/GT280/ GT28M only). ()/ () buttons To control CD/radio, the same as /+ on the unit. Setup, sound setting, etc., can be operated by. DSPL (display) button To change display items. VOL (volume) +/ button To adjust volume. ATT (attenuate) button To attenuate the sound. To cancel, press again. SEL (select) button The same as the select button on the unit. (+)/ ( ) buttons To control CD, the same as / (ALBUM /+) on the unit. Setup, sound setting, etc., can be operated by. SCRL (scroll) button To scroll the display item. Number buttons To receive stored stations (press); store stations (press and hold). Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless on the unit is pressed, or a disc is inserted to activate the unit first. 6 7 5

CONNECTIONS CDX-GT130/GT230: CDX-GT330/GT33W * 2 Supplied with XA-C40 Fourni avec le XA-C40 Suministrado con el XA-C40 Source selector () Sélecteur de source (non fourni) Selector de fuente (no suministrado) XA-C40 Supplied with the CD changer Fourni avec le changeur de CD Suministrado con el cambiador de CD * 2 FRONT AUDIO OUT * 1 Left Gauche Izquierdo Right Droit Derecho Left Gauche Izquierdo Right Droit Derecho BUS AUDIO IN* 1 from car antenna (aerial) à partir de l antenne du véhicule desde la antena del automóvil BUS IN L R REAR/SUB FRONT AUDIO OUT REAR / SUB AUDIO OUT* 3 Fuse (10 A) Fusible (10 A) Fusible (10 A) Blue/white striped Rayé bleu/blanc AMP REM Con rayas azules y blancas Max. supply current 0.3 A Courant max. fourni 0,3 A Corriente máx. de alimentación de 0,3 A White Blanc Blanco White/black striped Rayé blanc/noir Con rayas blancas y negras Gray Gris Gris Gray/black striped Rayé gris/noir Con rayas grises y negras Green Vert Verde Green/black striped Rayé vert/noir Con rayas verdes y negras Purple Violet Morado Purple/black striped Rayé violet/noir Con rayas moradas y negras BUS CONTROL IN* 1 Black Noir Negro Blue Bleu Azul Red Rouge Rojo Yellow Jaune Amarillo CDX-GT330 CDX-GT33W ANT REM Max. supply current 0.1 A Courant max. fourni 0,1 A Corriente máx. de alimentación de 0,1 A * 1 CDX-GT330/GT33W only * 2 RCA pin cord () * 3 AUDIO OUT can be switched SUB or REAR. For details, see the supplied Operating Instructions. * 1 CDX-GT330/GT33W uniquement * 2 Cordon à broche RCA (non fourni) * 3 AUDIO OUT peut être commuté sur SUB ou REAR. Pour obtenir plus de détails, reportez-vous au mode d emploi fourni. * 1 Solo CDX-GT330/GT33W * 2 Cable con terminales RCA (no suministrado) * 3 AUDIO OUT (salida de audio) puede cambiarse a SUB o REAR. Para obtener información, consulte el manual de instrucciones suministrado. Connection diagram To a metal surface of the car First connect the black ground (earth) lead, then connect the yellow and red power supply leads. To the power antenna (aerial) control lead or power supply lead of antenna (aerial) booster Notes It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial). When your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see Notes on the control and power supply leads. To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. To the +12 V power terminal which is energized in the accessory position of the ignition switch Notes If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground (earth) lead to a metal surface of the car first. When your car has a built-in FM/AM antenna (aerial) in the rear/side glass, see Notes on the control and power supply leads. To the +12 V power terminal which is energized at all times Be sure to connect the black ground (earth) lead to a metal surface of the car first. Notes on the control and power supply leads The power antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner. When your car has built-in FM/AM antenna (aerial) in the rear/ side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. A power antenna (aerial) without a relay box cannot be used with this unit. Memory hold connection When the yellow power supply lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Notes on speaker connection Before connecting the speakers, turn the unit off. Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. Do not connect the ground (earth) lead of this unit to the negative ( ) terminal of the speaker. Do not attempt to connect the speakers in parallel. Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative ( ) lead for the right and left speakers. Do not connect the unit s speaker leads to each other. Note on connection If speaker and amplifier are not connected correctly, FAILURE appears in the display. In this case, make sure the speaker and amplifier are connected correctly. Schéma de raccordement À un point métallique de la voiture Branchez d abord le câble de mise à la masse noir et, ensuite, les câbles d alimentation jaune et rouge. Au câble de commande d antenne électrique ou au câble d alimentation de l amplificateur d antenne Remarques Il n est pas nécessaire de raccorder ce câble s il n y a pas d antenne électrique ni d amplificateur d antenne, ou avec une antenne télescopique manuelle. Si votre voiture est équipée d une antenne FM/AM intégrée dans la vitre arrière/latérale, voir «Remarques sur les câbles de commande et d alimentation». Au niveau de AMP REMOTE IN de l amplificateur de puissance en option Ce raccordement s applique uniquement aux amplificateurs. Le branchement de tout autre système risque d endommager l appareil. À la borne d alimentation +12 V qui est alimentée quand la clé de contact est sur la position accessoires Remarques S il n y a pas de position accessoires, raccordez la borne d alimentation (batterie) +12 V qui est alimentée en permanence. Raccordez d abord le câble de mise à la masse noir à un point métallique du véhicule. Si votre voiture est équipée d une antenne FM/AM intégrée dans la vitre arrière/latérale, voir «Remarques sur les câbles de commande et d alimentation». À la borne d alimentation +12 V qui est alimentée en permanence Raccordez d abord le câble de mise à la masse noir à un point métallique du véhicule. Remarques sur les câbles de commande et d alimentation Le câble de commande d antenne électrique (bleu) fournit une alimentation de + 12 V CC lorsque vous mettez la radio sous tension. Lorsque votre voiture est équipée d une antenne FM/ AM intégrée dans la vitre arrière/latérale, raccordez le câble de commande d antenne électrique (bleu) ou le câble d alimentation des accessoires (rouge) à la borne d alimentation de l amplificateur d antenne existant. Pour plus de détails, consultez votre détaillant. Une antenne électrique sans boîtier de relais ne peut pas être utilisée avec cet appareil. Raccordement pour la conservation de la mémoire Lorsque le câble d alimentation jaune est raccordé, le circuit de la mémoire est alimenté en permanence même si la clé de contact est sur la position d arrêt. Remarques sur le raccordement des haut-parleurs Avant de raccorder les haut-parleurs, mettez l appareil hors tension. Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms avec une capacité électrique adéquate pour éviter de les endommager. Ne raccordez pas les bornes du système de haut-parleurs au châssis de la voiture et ne raccordez pas les bornes du hautparleur droit à celles du haut-parleur gauche. Ne raccordez pas le câble de mise à la masse de cet appareil à la borne négative ( ) du haut-parleur. N essayez pas de raccorder les haut-parleurs en parallèle. Raccordez uniquement des haut-parleurs passifs. Le raccordement de haut-parleurs actifs (avec amplificateurs intégrés) aux bornes des haut-parleurs peut endommager l appareil. Pour éviter tout problème de fonctionnement, n utilisez pas les câbles des haut-parleurs intégrés installés dans votre voiture si l appareil possède un câble négatif commun ( ) pour les hautparleurs droit et gauche. Ne raccordez pas entre eux les cordons des haut-parleurs de l appareil. Remarque sur le raccordement Si le haut-parleur et l amplificateur ne sont pas raccordés correctement, le message «FAILURE» s affiche. Dans ce cas, assurez-vous que les haut-parleurs et l amplificateur sont bien raccordés. Diagrama de conexión A una superficie metálica del automóvil Conecte primero el cable de conexión a masa negro, y después los cables amarillo y rojo de fuente de alimentación. Al cable de control de la antena motorizada o al cable de fuente de alimentación del amplificador de señal de la antena Notas Si no se dispone de antena motorizada ni de amplificador de antena, o se utiliza una antena telescópica accionada manualmente, no será necesario conectar este cable. Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte Notas sobre los cables de control y de fuente de alimentación. A AMP REMOTE IN de un amplificador de potencia opcional Esta conexión es sólo para amplificadores. La conexión de cualquier otro sistema puede dañar la unidad. Al terminal de alimentación de +12 V que recibe energía en la posición de accesorio del interruptor de encendido Notas Si no hay posición de accesorio, conéctelo al terminal de alimentación (batería) de +12 V que recibe energía sin interrupción. Asegúrese de conectar primero el cable de conexión a masa negro a una superficie metálica del automóvil. Si el automóvil incorpora una antena de FM/AM en el cristal trasero o lateral, consulte Notas sobre los cables de control y de fuente de alimentación. Al terminal de alimentación de +12 V que recibe energía sin interrupción Asegúrese de conectar primero el cable de conexión a masa negro a una superficie metálica del automóvil. Notas sobre los cables de control y de fuente de alimentación El cable de control de la antena motorizada (azul) suministrará cc de +12 V cuando conecte la alimentación del sintonizador. Si el automóvil dispone de una antena de FM/AM incorporada en el cristal trasero o lateral, conecte el cable de control de antena motorizada (azul) o el cable de fuente de alimentación auxiliar (rojo) al terminal de alimentación del amplificador de antena existente. Para obtener más información, consulte a su distribuidor. Con esta unidad no es posible utilizar una antena motorizada sin caja de relé. Conexión para protección de la memoria Si conecta el cable de fuente de alimentación amarillo, el circuito de la memoria recibirá siempre alimentación, aunque apague el interruptor de encendido. Notas sobre la conexión de los altavoces Antes de conectar los altavoces, desconecte la alimentación de la unidad. Utilice altavoces con una impedancia de 4 a 8 Ω con la capacidad de potencia adecuada para evitar que se dañen. No conecte los terminales de altavoz al chasis del automóvil, ni conecte los terminales del altavoz derecho con los del izquierdo. No conecte el cable de conexión a masa de esta unidad al terminal negativo ( ) del altavoz. No intente conectar los altavoces en paralelo. Conecte solamente altavoces pasivos. Si conecta altavoces activos (con amplificadores incorporados) a los terminales de altavoz, puede dañar la unidad. Para evitar fallas de funcionamiento, no utilice los cables de altavoz incorporados instalados en el automóvil si la unidad comparte un cable negativo común ( ) para los altavoces derecho e izquierdo. No conecte los cables de altavoz de la unidad entre sí. Nota sobre la conexión Si el altavoz y el amplificador no están conectados correctamente, aparecerá FAILURE en la pantalla. Si es así, compruebe la conexión de ambos dispositivos. 6

CDX-GT130/GT180/GT230/GT280/GT280S/GT282S CDX-GT180/GT280/GT280S/GT282S: CDX-GT282S/GT280S/GT280/GT28M *1 REMOTE IN *3 L R REAR/SUB AUDIO OUT from car antenna (aerial) desde la antena del automóvil REAR / SUB Fuse (10 A) AUDIO OUT*2 Fusible (10 A) Blue/white striped Con rayas azules y blancas *1 RCA pin cord () *2 AUDIO OUT can be switched SUB or REAR. For details, see the supplied Operating Instructions. *3 Insert with the cord upwards. AMP REM Max. supply current 0.3 A Corriente máx. de alimentación de 0,3 A White Blanco Left Izquierdo Left Izquierdo ANT REM Green Verde Connection diagram To a metal surface of the car First connect the black ground (earth) lead, then connect the yellow, and red power supply leads. To the power antenna (aerial) control lead or power supply lead of antenna (aerial) booster amplifier Notes It is not necessary to connect this lead if there is no power antenna (aerial) or antenna (aerial) booster, or with a manually-operated telescopic antenna (aerial). When your car has a built-in FM/MW/SWantenna (aerial) in the rear/side glass, see Notes on the control and power supply leads. To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. To the +12 V power terminal which is energized in the accessory position of the ignition key switch Notes If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground (earth) lead to a metal surface of the car first. When your car has a built-in FM/MW/SW antenna (aerial) in the rear/side glass, see Notes on the control and power supply leads. To the +12 V power terminal which is energized at all times Be sure to connect the black ground (earth) lead to a metal surface of the car first. Notes on the control and power supply leads The power antenna (aerial) control lead (blue) supplies +12 V DC when you turn on the tuner. When your car has built-in FM/MW/SW antenna (aerial) in the rear/side glass, connect the power antenna (aerial) control lead (blue) or the accessory power supply lead (red) to the power terminal of the existing antenna (aerial) booster. For details, consult your dealer. A power antenna (aerial) without a relay box cannot be used with this unit. Max. supply current 0.1 A Corriente máx. de alimentación de 0,1 A Red Rojo Green/black striped Con rayas verdes y negras Purple/black striped Con rayas moradas y negras *1 Cable con terminales RCA (no suministrado) *2 AUDIO OUT (salida de audio) puede cambiarse a SUB o REAR. Para obtener información, consulte el manual de instrucciones suministrado. *3 Insertar con el cable hacia arriba. Blue Azul Gray/black striped Con rayas grises y negras Purple Morado Right Derecho White/black striped Con rayas blancas y negras Gray Gris Right Derecho Black Negro Yellow Amarillo Diagrama de conexión A una superficie metálica del automóvil Conecte primero el cable de conexión a masa negro, y después los cables amarillo y rojo de fuente de alimentación. Al cable de control de la antena motorizada o al cable de fuente de alimentación del amplificador de señal de la antena Notas Si no se dispone de antena motorizada ni de amplificador de antena, o se utiliza una antena telescópica accionada manualmente, no será necesario conectar este cable. Si el automóvil incorpora una antena de FM/MW/SW en el cristal trasero o lateral, consulte Notas sobre los cables de control y de fuente de alimentación. A AMP REMOTE IN de un amplificador de potencia opcional Esta conexión es sólo para amplificadores. La conexión de cualquier otro sistema puede dañar la unidad. Al terminal de alimentación de +12 V que recibe energía en la posición de accesorio del interruptor de encendido Notas Si no hay posición de accesorio, conéctelo al terminal de alimentación (batería) de +12 V que recibe energía sin interrupción. Asegúrese de conectar primero el cable de conexión a masa negro a una superficie metálica del automóvil. Si el automóvil incorpora una antena de FM/MW/SW en el cristal trasero o lateral, consulte Notas sobre los cables de control y de fuente de alimentación. Al terminal de alimentación de +12 V que recibe energía sin interrupción Asegúrese de conectar primero el cable de conexión a masa negro a una superficie metálica del automóvil. Notas sobre los cables de control y de fuente de alimentación El cable de control de la antena motorizada (azul) suministrará cc de + 12 V cuando conecte la alimentación del sintonizador. Si el automóvil dispone de una antena de FM/MW/SW incorporada en el cristal trasero o lateral, conecte el cable de control de antena motorizada (azul) o el cable de fuente de alimentación auxiliar (rojo) al terminal de alimentación del amplificador de antena existente. Para obtener más información, consulte a su distribuidor. Con esta unidad no es posible utilizar una antena motorizada sin caja de relé. Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition switch is turned off. Conexión para protección de la memoria Si conecta el cable de fuente de alimentación amarillo, el circuito de la memoria recibirá siempre alimentación, aunque apague el interruptor de encendido. Notes on speaker connection Before connecting the speakers, turn the unit off. Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers with those of the left speaker. Do not connect the ground (earth) lead of this unit to the negative ( ) terminal of the speaker. Do not attempt to connect the speakers in parallel. Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the unit. To avoid a malfunction, do not use the built-in speaker leads installed in your car if the unit shares a common negative ( ) lead for the right and left speakers. Do not connect the unit s speaker leads to each other. Notas sobre la conexión de los altavoces Antes de conectar los altavoces, desconecte la alimentación de la unidad. Utilice altavoces con una impedancia de 4 a 8 Ω con la capacidad de potencia adecuada para evitar que se dañen. No conecte los terminales de altavoz al chasis del automóvil, ni conecte los terminales del altavoz derecho con los del izquierdo. No conecte el cable de conexión a masa de esta unidad al terminal negativo ( ) del altavoz. No intente conectar los altavoces en paralelo. Conecte solamente altavoces pasivos. Si conecta altavoces activos (con amplificadores incorporados) a los terminales de altavoz, puede dañar la unidad. Para evitar fallas de funcionamiento, no utilice los cables de altavoz incorporados instalados en el automóvil si la unidad comparte un cable negativo común ( ) para los altavoces derecho e izquierdo. No conecte los cables de altavoz de la unidad entre sí. Note on connection If speaker and amplifier are not connected correctly, FAILURE appears in the display. In this case, make sure the speaker and amplifier are connected correctly. Nota sobre la conexión Si el altavoz y el amplificador no están conectados correctamente, aparecerá FAILURE en la pantalla. Si es así, compruebe la conexión de ambos dispositivos. 7

SECTION 3 DISASSEMBLY Note: This set can be disassembled in order shown below. SET 3-1. SUB PANEL ASSY (Page 9) 3-2. CD MECHANISM BLOCK (Page 9) 3-3. MAIN BOARD (Page 10) 3-4. SERVO BOARD (Page 10) 3-5. CHASSIS (T) SUB ASSY (Page 11) 3-6. ROLLER ARM ASSY (Page 11) 3-7. CHASSIS (OP) ASSY (Page 12) 3-8. CHUCKING ARM SUB ASSY (Page 12) 3-9. SLED MOTOR ASSY (Page 13) 3-10. OPTICAL PICK-UP SECTION (Page 14) 3-11. OPTICAL PICK-UP (Page 14) 8

Note: Follow the disassembly procedure in the numerical order shown below. 3-1. SUB PANEL ASSY two claws two claws two screws (+PTT 2.6 6) sub panel assy 3-2. CD MECHANISM BLOCK CD mechanism block bracket (CD) two screws (+PTT 2.6 4) screw (+PTT 2.6 6) CNP301 screw (+PTT 2.6 6) 9

3-3. MAIN BOARD three ground point screws (+PTT 2.6 6) two screws (+PTT 2.6 8) two screws (+P 2.6 8) two screws (+PTT 2.6 10) screw (+P 2.6 10) heat sink screw (+PTT 2.6 10) MAIN board insulating sheet 3-4. SERVO BOARD WHT RED BLK WHT RED BLK RED ORG BLU YEL GRY SERVO board toothed lock screw (M 1.7 2.5) toothed lock screw (M 1.7 2.5) Remove the eleven solders. SERVO board claw optical pick-up (16 core) (CN101) claw 10

3-5. CHASSIS (T) SUB ASSY two precision screws (+P 1.7 2.2) two precision screws (+P 1.7 2.2) chassis (T) sub assy claw 3-6. ROLLER ARM ASSY roller arm assy gear (RA1) spring (RAL) washer spring (RAR) 11

3-7. CHASSIS (OP) ASSY chassis (OP) assy tension spring (KF) coil spring (damper) (natural) slider (R) coil spring (damper) (green) lever (D) gear (LE1) 3-8. CHUCKING ARM SUB ASSY chucking arm sub assy spring Note: Have this portion receive the chassis. Note: Have this portion receive the chassis. Note: Be careful not to touch the turn table. 12

3-9. SLED MOTOR ASSY three serration screws (M 2 3) sled motor assy turn table spring spring stand Note: Never remove these parts since they were adjusted. bearing(f) stand Note: Place the stand with care not to touch the turn table. bearing(r) Note for Assembly three serration screws (M 2 3) sled motor assy Note: Take care to prevent the chassis from being bent when tightening the three machine screws. 13

3-10. OPTICAL PICK-UP SECTION optical pick-up section Note: Be careful not to touch the lens and hologram terminal when removing the optical pick-up section. 3-11. OPTICAL PICK-UP pan tapping screw (M 1.4 2.5) leaf spring (sub guide) leaf spring (OP) optical pick-up lead screw assy Notes for Assembly Prevent the end of the leaf spring (sub guide) from being in contact with the OP slide base. Prevent the end of the leaf spring (sub guide) from being in contact with the OP slide base. There is space at the end of the leaf spring (sub guide) to avoid contact with the slide. 14

4-1. BLOCK DIAGRAM MAIN SECTION SECTION 4 DIAGRAMS CDX-GT130/GT180/GT230/GT280/GT280S/GT282S ELECTRONIC VOLUME IC401 J901 AUX J1 (ANTENNA) R-CH L6 FM MIX L2 PHASE LOCKED LOOP (PLL) IC1 4 FMIN1 3 FMIN2 1 AMRFIN LOUT ROUT 8 9 R-CH R-CH R-CH R-CH 9 AUX-L 7 AUX-R 8 AUX GND 4 TU-L 3 TU-R 6 CD-L 5 CD-R SUB L 30 SUB R 31 OUT-FL 34 OUT-RL 32 OUT-FR 35 OUT-RR 33 SCL 37 SDA 38 I2C-SCL I2C-SDA R-CH R-CH (FRONT) R-CH (REAR) MUTE Q481 MUTE CONTROL SWITCH Q478,479 MUTE Q441 MUTE Q461 R-CH D479 BATT I2C BUS CONTROLLED POWER AMP/MULTIPLE VOLTAGE REGULATOR IC750 R-CH R CN601 1 12 IN-FL OUT-FL+ 5 FL+ 9 OUT-FL 3 FL 11 IN-RL OUT-RL+ OUT-RL 9 7 AMP-REM 29 R-CH L 2 RL+ 10 RL 4 FR+ 12 FR 3 RR+ 11 RR 5 AMP-REM J330 AUDIO OUT REAR/SUB X1 4MHz 16 XTAL1 15 XTAL2 SCL 18 SDA 19 I2C-SCL I2C-SDA SYSTEM CONTROL IC501 (1/2) I2C-SCL I2C-SDA 4 SCL 2 SDA ANT-REM 27 VP 35 VP1 20 VP2 6 BATT FU601 6 ANT-REM 16 BATT CNP301 11 15 AU_LCH AU_RCH R-CH RSSI 14 93 VSM I2C_SCK 29 I2C_SIO 30 ATT 56 BEEP 28 AMPSTB 58 DIAG 57 I2C-SCL I2C-SDA D511 16 BEEP 22 STB 25 DIAG BU+B 37 AUDIO+B 30 SERVO+3.3V 31 MECHA+6V 33 PANEL+B 34 B.U+5V AUDIO +8.5V SERVO+3.3V MECHA+6V PANEL+B CD MECHANISM UNIT (MG-101L) 22 24 26 16 5 7 6 21 27 UNI_SO UNI_SI UNI_CLK Z_MUTE CD_ON CDM_ON SYS_RST EJECT_OK BUS_ON BU+3.3V D510 D512 5 UNISO 6 UNISI 7 UNISCK 21 Z-MUTE 52 CD_ON 20 CDM_ON 12 RESET 43 SYSRST 44 BUSON ACC IN 55 BUIN 19 BATTERY CHECK Q582 LOW VOLTAGE CHECK Q581,D580 BATT ACCESSORY CHECK Q631 7 ACC 9 25 18 19 8 1,2 A_ATT BU_IN D_+3.3V A_+3.3V BU_+3.3V DR_+6V SERVO +3.3V BU_+3.3V MECHA +6V RESET IC602 1 VOUT VDD 2 BU +3.3V BU+3.3V BU+3.3V REG IC681 OVER VOLTAGE CHECK Q580,D581 B.U +5V R-CH is omitted due to same as L-CH. Signal Path : CD PLAY : FM : AM/MW/SW : AUX CDX-GT130/GT180/GT230/GT280/GT280S/GT282S 15 15

4-2. BLOCK DIAGRAM DISPLAY SECTION KEY MATRIX LSW901 914, S901 RE901 PUSH SELECT (VOLUME) ROTARY ENCODER GT280/GT280S/GT282S J561 (REMOTE IN) RE-0 RE-1 GT230/GT280/GT280S/GT282S X502 32.768kHz X501 11.06MHz 94 KEYIN1 95 KEYIN0 10 XIN SYSTEM CONTROL IC501 (2/2) 92 KEYACK1 82 RE-IN0 81 RE-IN1 42 RC IN1 97 RC IN0 91 KEYACK 11 XOUT 15 OSCIN 13 OSCOUT LCD_SO LCD_CKO 1 2 LCD_CE 100 48 DI 47 CL 46 CE LCD DRIVE IC901 BACK LIGHT 1 DIMMER 2 S1 I S48 3 34 39 COM1 35 I COM4 38 LED931 LCD BACK LIGHT ( ) DIMMER SWITCH Q931 LCD BACK LIGHT SWITCH Q932 LCD901 LIQUID CRYSTAL DISPLAY PANEL PANEL+B LED941,944,951 953, 982,1951,1952, LSW901 914 KEY ( ILLUMINATE ) THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. Note: X : Parts extracted from the component side. a : Through hole. : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: (SIDE B) Parts face side: (SIDE A) Indication of transistor. C Q B E Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. These are omitted. For schematic diagrams: Note: All capacitors are in μf unless otherwise noted. (p: pf) 50 WV or less are not indicated except for electrolytics and tantalums. All resistors are in Ω and 1 /4 W or less unless otherwise specifi ed. f : internal component. C : panel designation. Note: The components identifi ed by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specifi ed. Note: Les composants identifi és par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifi é. A : B+ Line. B : B Line. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM ( ): AM/MW/SW < > : CD PLAY Voltages are taken with VOM (Input impedance 10 MΩ). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. J : CD PLAY F : FM f : AM/MW/SW L : AUX REMOTE CONTROL SIGNAL RECEIVER IC971 4 SIRCS Waveforms 3 NOSE_SW MAIN Board GT180/GT280/GT280S/GT282S BU+3.3V IC1 (XTAL 1) IC501 (OSCIN) S502 FREQUENCY SELECTOR 10k 9k 70 AREASEL2 4MHz 0.04 Vp-p 11.06MHz 1.7 Vp-p 0.05 V/DIV, 0.5 μ sec/div 0.5 V/DIV, 0.1 μsec/div IC501 (XIN) 0.8 Vp-p 32.768 khz 0.5 V/DIV, 20 μsec/div CDX-GT130/GT180/GT230/GT280/GT280S/GT282S 16 16

CDX-GT130/GT180/GT230/GT280/GT280S/GT282S 4-3. PRINTED WIRING BOARD MAIN SECTION 2 1 : Uses unleaded solder. 3 4 5 6 7 8 9 10 11 12 13 J330 AUDIO OUT REAR/SUB A J1 (ANTENNA) L J561 (REMOTE IN) R -1-2 C775 C774 CN601 FB563 JW157 JW158 JC755 C454 JW159 JC754 JW122 C464 GT280 /GT280S /GT282S JW32 FU601 C705 JW139 C707 C709 C551 CN701 I D719 R513 R570 FB561 R532 JW4 D754 JW21 C513 R511 R510 R512 GT280/GT280S/GT282S JW5 JW26 JW27 JW109 JW115 JC302 JW111 R673 X502 FMB4 JW62 CN351 8 JW36 FB604 C507 R536 R542 C508 R533 R535 JC501 R519 D502 32 41 R601 C519 S702 11 1-877-020- (11) R558 GT230/GT280/GT280S/GT282S X501 KEY BOARD CN901 (Page 21) 17 17 Semiconductor Location Ref. No. JW63 JW49 JW140 R674 JW166 JW82 JW28 C305 R529 JW50 JW152 JW59 JW106 JW99 C306 JW108 JW30 JW118 JW153 JW154 JW174 S702 RESET CDX-GT130/GT180/GT230/GT280/GT280S/GT282S Q582 R541 GT280/GT280S /GT282S R565 R567 JC503 (CHASSIS) A R584 JC533 R547 JW47 D753 JW10 JW23 C514 C502 R671 R514 FB308 JW167 R502 R503 R561 C509 R543 JW75 R505 R585 JW57 C510 C512 C501 R504 R540 R679 JW65 C503 GT230/GT280/ GT280S/GT282S C708 C719 R528 Q581 JW120 FB309 JW176 IC501 C522 R664 CD MECHANISM UNIT (MG-101L) JW175 R522 IC602 C706 JW105 JW104 JC151 D702 JW142 D703 R662 JW79 JC580 D512 FB311 R301 R578 R521 R526 R507 R663 GT180/GT280 R661 /GT280S/GT282S C523 JC301 C312 R677 JW141 D153 L151 R152 D701 D704 R506 JW78 C309 CNP301 D580 1 X501 C155 C157 R537 JW80 R154 H R155 JW76 R153 R550 R551 GT130/GT230 R538 C152 C154 C151 C153 R575 R582 D581 Q580 R509 R546 JW67 R675 R501 JW83 R676 JW40 GT180/GT280/GT280S/GT282S JW69 JW74 JW73 JW54 JW103 G JW56 9k JW71 R14 D511 R636 GT230/GT280 R531 /GT280S/GT282S R692 R534 C504 GT130 R523 /GT230 R693 R690 R566 GT130/GT230 R574 R635 C343 FB312 FMB3 R672 JW90 FB562 GT280/GT280S /GT282S C301 C310 R302 C521 D510 R508 JW135 R13 R563 S502 JW45 L1 10k C302 C308 C520 JC521 R530 JW89 JW126 JW102 JW124 X1 R756 JW51 S502 FREQUENCY SELECTOR C28 FB304 JC303 R539 C683 JW66 GT180/GT280/GT280S/GT282S C18 R10 R6 JW156 JW155 C27 F C406 L601 R583 Q631 C682 JW97 JW29 JW129 R12 JW147 R556 JW94 JW130 C407 JW96 C26 JW148 C17 C25 C754 JW68 R4 R5 R414 JW91 JW161 R631 JW55 JW95 R11 C22 C23 IC681 C681 C479 C24 C16 Q478 JW98 R413 IC1 E D479 R633 JW160 R634 R479 JW133 C13 C9 C21 Q479 C756 C755 JW136 JW42 R752 JW101 JW31 JW100 JW39 JW85 IC401 JW37 JW33 L7 C776 C632 R632 JW178 JW93 JW132 L8 C405 C12 C413 C409 FB402 C20 C7 FB401 C408 JW131 C19 C404 C5 JW24 JW88 C412 JW92 C8 C770 JW25 C461 R401 C401 L4 C761 C752 R461 C431 GT180/GT280/ GT280S/GT282S JW121 D601 D761 C631 C750 C602 D762 D759 JW151 JW35 C601 D760 JW8 JW17 Q461 D617 JW18 JW38 C758 R451 C451 C455 J561 C617 JW7 C769 C623 JW20 C471 R452 R462 JW149 FB1 FB2 C2 L6 C465 L2 R3 JW13 C462 C441 L3 R2 D (CHASSIS) GT180/GT280/ GT280S/GT282S C481 C6 C1 C3 D756 JW6 JW150 R481 Q451 JW2 JW3 C618 JC502 C452 JW15 JW86 R431 JW146 R441 JW16 JW48 C435 D755 C445 JW14 JW22 JW137 VDR1 C442 C432 JW19 Q481 C753 C622 C JW138 R1 R471 JW9 JW1 C763 R442 C764 IC750 C765 JW11 R432 Q431 Q441 C771 JW84 Q471 C751 JW34 B R472 JW12 R482 D153 D479 D502 D510 D511 D512 D580 D581 D601 D617 D701 D702 D703 D704 D719 D753 D754 D755 D756 D759 D760 D761 Location H-2 E-5 I-6 F-6 F-5 E-8 D-9 D-9 C-9 C-8 H-3 H-3 H-3 H-3 I-4 C-6 C-6 C-6 C-6 C-7 C-7 C-8 Ref. No. Location D762 C-8 IC1 IC401 IC501 IC602 IC681 IC750 E-2 E-3 G-6 H-7 E-6 B-6 Q431 Q441 Q451 Q461 Q471 Q478 Q479 Q481 Q580 Q581 Q582 Q631 B-4 B-3 C-4 D-4 B-3 E-5 D-5 C-3 D-9 E-10 F-10 D-8

D754 D753 D755 D756 D762 D761 D760 D759 JC755 CDX-GT130/GT180/GT230/GT280/GT280S/GT282S 4-4. SCHEMATIC DIAGRAM MAIN SECTION (1/3) See page 23 for IC Block Diagrams. IC B/D C756 R752 JC754 C764 C753 C754 C765 C776 C761 C758 C771 C751 C755 C774 C775 R631 Q631 R635 R633 IC750 R632 C632 C631 R634 CN601 C770 C769 C750 C752 C763 (Page 19) C618 C617 D617 FU601 IC602 L601 C601 D601 C602 R601 C519 FB604 C503 JC502 C683 C682 IC681 C681 C622 C623 R540 R541 R584 R585 Q582 Q581 D580 R582 Q580 D581 R583 J561 FB563 FB561 FB562 JW63 (Page 20) CDX-GT130/GT180/GT230/GT280/GT280S/GT282S 18 18

D704 D703 D702 D701 D153 C13 R4 R5 C17 IC1 R12 C27 R13 R14 C20 C21 L7 L8 C22 C23 R11 C25 C19 C24 CDX-GT130/GT180/GT230/GT280/GT280S/GT282S 4-5. SCHEMATIC DIAGRAM MAIN SECTION (2/3) See page 16 for Waveform. See page 24 for IC Block Diagrams. J330 J1 C442 C445 C464 C454 C432 C435 C452 C455 Q461 Q451 Q441 Q431 Q481 Q471 VDR1 C26 C28 C462 C465 C6 C1 R1 FB1 FB2 R2 R462 R452 R442 R432 R482 R472 L2 C2 R461 R451 R441 R431 R481 R471 C461 C451 C441 C431 C481 C471 L3 C3 R3 L4 L6 C5 X1 C7 R10 C18 R6 C8 C12 C16 (Page 18) L1 C9 C405 C404 D479 Q479 FB402 C409 FB401 C408 R479 C479 IC B/D Q478 R414 R413 D511 C551 C412 C413 R401 C401 IC401 IC B/D C406 C407 C152 C151 C153 R153 R155 R152 R154 R151 L151 C154 C157 C155 JC151 C719 D719 C709 CN701 (Page 22) C708 C707 C706 C705 (Page 20) CDX-GT130/GT180/GT230/GT280/GT280S/GT282S 19 19

R547 R514 R533 R519 R532 R513 R536 R542 C508 C507 R529 C510 R521 R522 C520 C521 R512 R570 JC501 R543 R677 X502 R501 R662 R664 FB311 FB309 FB312 FB304 R507 R538 R551 R575 R537 R574 R693 R692 R550 R523 R526 R566 R690 R531 R534 R556 R636 R563 CDX-GT130/GT180/GT230/GT280/GT280S/GT282S 4-6. SCHEMATIC DIAGRAM MAIN SECTION (3/3) See page 16 for Waveforms. See page 26 for IC Pin Description of IC501. (Page 18) JC303 C310 C309 R301 S502 JW69 JW83 R546 C504 CNP301 R539 JC301 R302 JW67 C308 C302 C522 R663 C523 R506 R530 C301 C343 C312 R661 R528 C305 C306 FB308 JC302 R504 C501 C512 C514 IC501 R5F3640DDA07FA R675 R676 R672 JC503 R674 R578 D510 R505 R673 R502 R503 R671 R565 (Page 19) C513 C502 R511 R567 CN351 R679 JC533 D512 R510 D502 R509 R508 R561 C509 R756 R535 X501 R558 JC521 CDX-GT130/GT180/GT230/GT280/GT280S/GT282S 20 20

D998 R903 R933 R932 R931 D903 D992 D991 D993 D994 R987 D982 D986 D985 R974 R977 C981 R988 C987 C984 C983 R950 R910 R952 R912 R913 R914 LED982 R953 R954 R915 R947 R907 C971 LED931 LED941 R946 LSW913 LED951 R942 CDX-GT130/GT180/GT230/GT280/GT280S/GT282S 4-7. PRINTED WIRING BOARD KEY SECTION : Uses unleaded solder. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A B LSW902 OFF LSW913 SEEK+ LSW902 C990 R902 LSW903 SOURCE LSW903 R941 LED951 953,982,1951,1952, (RING ILLUMINATION) R971 LED944 (CD INDICATER) LED944 1 LED931 (LCD BACK LIGHT) 37 LSW901 LSW901 C D E LSW912 DSPL (GT130/GT180) DSPL/SCRL GT230/GT280 /GT280S/GT282S LSW914 SEEK LSW912 R944 R905 R904 S901 LED941,S901 EQ3 LSW914 R908 LSW904 LED1952 GT230 LED953 GT130/GT180 /GT280/GT280S/GT282S GT230 R1971 LED952 GT230 LED1951 GT130/GT180 /GT280/GT280S/GT282S LSW905 LSW906 LSW907 LCD901 LIQUID CRYSTAL DISPLAY PANEL LSW904 LSW905 LSW906 LSW907 LSW908 LSW909 MODE BTM 1 2 3/REP 4/SHUF 5 6/PAUSE (GT130/GT180) (GT130/GT180) 1/ALBUM 2/ALBUM+ GT230/GT280 /GT280S/GT282S GT230/GT280 /GT280S/GT282S LSW908 LSW909 LSW910 LSW910 LSW911 1-877-026- (Page 17) MAIN BOARD CN701 A LSW911 IC971 4 3 1 2 R975 GT230/GT280 /GT280S/GT282S IC971 11 (11) R911 F R901 R909 R948 R972 R922 R949 R992 R978 R979 R986 R985 R984 R951 C986 D981 CN901 J901 G R943 R945 R1972 GT230 C921 C922 RE901 R921 R982 C999 IC901 R981 GT230/GT280 /GT280S/GT282S FB903 Q931 R934 J901 AUX H RE901 PUSH SELECT (VOLUME) Q932 1-877-026-11 (11) Semiconductor Location CDX-GT130/GT180/GT230/GT280/GT280S/GT282S Ref. No. Location D903 G-11 D981 F-10 D982 G-9 D985 G-12 D986 G-12 D991 G-11 Ref. No. Location Ref. No. Location Ref. No. Location D992 G-11 D993 G-11 D994 G-11 IC901 G-8 IC971 C-13 LED931 C-13 LED941 C-2 LED944 B-7 LED951 B-4 LED952 C-5 LED953 C-4 LED982 D-4 LED1951 C-5 LED1952 C-4 Q931 G-13 Q932 H-13 21 21

LSW913(1/2) LSW914(1/2) LSW904(1/2) LSW905(1/2) LSW906(1/2) LSW907(1/2) LSW908(1/2) LSW909(1/2) LSW910(1/2) LSW911(1/2) D986 D985 D991 D992 D993 D903 D994 LSW901(1/2) LSW902(1/2) LSW903(1/2) S901 LSW912(1/2) D981 D982 R987 CDX-GT130/GT180/GT230/GT280/GT280S/GT282S 4-8. SCHEMATIC DIAGRAM KEY SECTION R981 R931 LED944 R945 R949 LSW910(2/2) LED951 R982 R932 R933 LED931 R941 LSW912(2/2) R943 LSW913(2/2) R947 LSW905(2/2) LSW909(2/2) R953 LED1951 LED982 R971 LED952 IC971 R975 LSW914(2/2) LSW908(2/2) LED953 C971 LSW902(2/2) R950 R954 R1971 R934 Q931 C990 LSW901(2/2) LED941 LSW903(2/2) LSW904(2/2) LSW906(2/2) R951 LSW911(2/2) LED1952 R972 C981 C983 C984 R984 R985 R986 IC901 LSW907(2/2) Q932 R942 R944 R946 R948 R952 R1972 C986 C987 R988 R977 R978 R979 D998 R992 CN901 C999 C922 C921 LCD901 R974 R901 R902 R903 R904 RE901 R922 R921 R905 (Page 19) R907 R908 R909 R910 R911 R912 R913 R914 R915 FB903 J901 CDX-GT130/GT180/GT230/GT280/GT280S/GT282S 22 22

IC Block Diagrams IC750 TDA8588AJ/N2/R1 (MAIN Board (1/3)) TAB 1 OUT FL 3 I 2 C BUS 2 SDA FL 4 SCL OUT FL+ 5 6 VP2 OUT RL 7 OUT RL+ 9 RL 8 PGND1 IN RL 11 S GND 13 IN RR 15 OUT RR+ 17 OUT RR 19 PROTECTION/ DIAGNOSTIC RR MUTE MUTE VP 10 SVR 12 IN FL 14 IN FR 16 BEEP 18 PGND3 OUT FR+ 21 OUT FR 23 FR STANDBY/ MUTE 20 VP1 22 STB DIAG 25 CHIP DETECT/ DIAGNOSTIC BATTERY DETECTION TEMPERATURE PROTECTION ENABLE LOGIC 24 PGND4 26 RST ANT REM 27 SWITCH 28 CRES AMP REM 29 SWITCH 30 AUDIO+B SERVO3.3V 31 MECH6V 33 VP 35 REGULATOR 32 GND 34 PANEL+B REFERENCE VOLTAGE 36 CBU BU+B 37 REGULATOR LOADDUMP PROTECTION BACK-UP SWITCH 23

IC1 TEF6607T/V3/S470, 518 (MAIN Board (2/3)) AMRFIN 1 AMRFDEC 2 FMIN2 3 FMIN1 4 FM TUNER AM TUNER 32 AMOUT2 31 AMOUT1 30 AMIFAGC1 29 AMSELIN2 GNDRF 5 28 AMSELIN1 VCC+8.5V 6 27 TESTCT AMRFAGC 7 LOUT 8 ROUT 9 GNDAUD 10 OUTPUT STEREO DECODER HIGH CUT SOFT MUTE NOISE BLANKER PLL TUNING SYSTEM 26 VCOREF 25 VCOLOOP 24 VCCVCO 23 GNDANA AMIFAGC 11 MPXIN 12 MPXOUT 13 RSSI 14 SIGNAL IMPROVEMENT CONTROL BANDWIDTH CONTROL POWER SUPPLY 22 VCC+8.5V 21 GREGSUP 20 VREF+4V 19 SDA XTAL2 15 I2C BUS 18 SCL XTAL1 16 17 GNDDIG 24

IC401 BD3447AFV-E2 (MAIN Board (2/3)) FIL 40 GND SDA SCL 39 38 37 VCC OUT-FR OUT-FL OUT-RR OUT-RL SUB-R SUB-L SAOUT SADA SACLK MIN1 MIN2 EBIAS2 DS2-R DS1-R DS3-R 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 I2C BUS LOGIC, VCO FADER FADER FADER FADER FADER EFFECT LPF HPF 180/0 3 BAND P-EQ (TONE CONTROL) 7 BAND SPECTRUM ANALYZER /LEVEL METER VOLUME/MUTE SPEANA SPEANA LVL METER LVL METER INPUT GAIN INPUT SELECTOR (3 SIGLE-END AND 3 STEREO IS O) GND ISO AMP GND ISO AMP GND ISO AMP GND ISO AMP GND ISO AMP GND ISO AMP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 BUS-R BUS-L TU-R TU-L CD-R CD-L AUX-R AUX-G AUX-L PD-R PD-G PD-L FP1 FN1 FN2 FP2 EBIAS1 DS2-L DS1-R DS3-R 25

IC Pin Function Description MAIN BOARD IC501 R5F3640DDA07FA (SYSTEM CONTROL) Pin No. Pin Name I/O Description 1 LCD SO O Liquid crystal display panel serial data signal output 2 LCD CKO O Liquid crystal display panel serial clock signal output 3 NOSE SW I Panel detection signal input 4 SIRCS I Remote control signal input 5 UNISO O SONY BUS serial data signal output 6 UNISI I SONY BUS serial data signal input 7 UNISCK O SONY BUS serial clock signal output 8 BYTE I Connect to ground. (Pull down) 9 CNVSS I Flash write signal input Normally operation: L, Flash write: H 10 XIN I Low speed operation clock signal input (32.768kHz) 11 XOUT O Low speed operation clock signal output (32.768kHz) 12 RESET I Reset signal input 13 OSCOUT O High speed operation clock signal output (11.06MHz) 14 VSS Ground pin 15 OSCIN I High speed operation clock signal input (11.06MHz) 16 VCC1 Power supply pin (+3.3V) 17 NMI I External pull up pin (fi xed at H.) 18 DAVN I RDS data block cycle detection signal input Not used. 19 BUIN I Back up power supply detection signal input 20 CDM ON I CD mechanism deck power supply control request signal input 21 Z MUTE I Mute signal input 22 to 27 NCO O Not used. (Open) 28 BEEP O Beep signal output to power amplifi er 29 I2C SCK O I2C serial clock signal output 30 I2C SIO I/O I2C serial data signal input/output 31 FW TXD O Flash write interface serial data signal output 32 FW RXD I Flash write interface serial data signal input 33 FW CLK I Flash write interface serial clock signal input 34 FW BUSY O Flash write interface serial busy signal output 35 to 40 NCO O Not used. (Open) 41 EPM O EPM signal output (fi xed at L.) 42 RCIN1 I Rotary commander shift key signal input 43 SYSRST O System reset signal output 44 BUSON O BUS ON signal output 45 NCO O Not used. (Open) 46 CE O CE signal output (fi xed at L.) 47 to 51 NCO O Not used. (Open) 52 CD ON I CD mechanism servo power supply control request signal input 53 TESTIN I Test mode detection signal input Not used. 54 TELATT I Telephone attenuate detection signal input Not used. 55 ACC IN I Accessory power supply detection signal input 56 ATT O Audio mute control signal output 57 DIAG I Condition signal input from power amplifi er IC 58 AMPSTB O Standby signal output to power regulator IC 59 VOLATT O Electrical volume attenuate control signal output Not used. 60 NCO O Not used. (Open) 61 CODEC SEL I CODEC setting signal input 62 VCC2 Power supply pin (+3.3V) 63 COL SEL I COL setting signal input 64 VSS Ground pin 65 ILLUMI SEL I Illumination voltage setting signal input for panel H : 10.4V, L : 9V 66 DEMO SEL I DEMO setting signal input H : DEMO on, L : DEMO off 67 DIM SEL I Dimmer function setting signal input H : Dimmer 68 B OUT SEL I Black out setting signal input H : Block out 26

Pin No. Pin Name I/O Description 69 AREASEL 3 I Destination setting pin 3 70 AREASEL 2 I Destination setting pin 2 71 AREASEL 1 I Destination setting pin 1 72 AREASEL 0 I Destination setting pin 0 73 to 80 NCO O Not used. (Open) 81 RE IN1 I Rotary encoder signal input 1 82 RE IN0 I Rotary encoder signal input 0 83 SAIN I Spectrum analyzer signal input Not used. (Open) 84 CYRIL SEL I Cyril correspondence discrimination signal input H : Correspondence, L : No correspondence 85 TUATT O Tuner mute control signal output Not used. (Open) 86 NCO O Not used. (Open) 87 RDS ON O RDS IC power supply control signal output Not used. (Open) 88 NCO O Not used. (Open) 89 SADATA O Spectrum analyzer data signal output Not used. (Open) 90 SACLK O Spectrum analyzer clock signal output Not used. (Open) 91 KEYACK0 I Key Acknowledge detection signal input (Rotary command signal input) 92 KEYACK1 I Key Acknowledge detection signal input (Front panel signal input) 93 VSM I S meter voltage detection signal input 94 KEYIN1 I Key signal input 1 95 KEYIN0 I Key signal input 0 96 AVSS Ground pin for A/D converter 97 RC IN0 I Rotary commander key signal input 98 AVRH A/D converter external reference power supply pin (+3.3V) 99 AVDD A/D converter power supply pin (+3.3V) 100 LCD CE O Liquid crystal display panel chip enable signal output 27

SECTION 5 EXPLODED VIEWS Note: -XX and -X mean standardized parts, so they may have some difference from the original one. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The mechanical parts with no reference number in the exploded views are. Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE)... (RED) Parts Color Cabinet s Color Accessories are given in the last of this parts list. The components identifi ed by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specifi ed. Les composants identifi és par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifi é. 5-1. MAIN SECTION MG-101L-188//C #2 6 #3 #5 FU601 #4 #1 5 4 #6 #4 #3 3 #1 2 #1 #1 front panel section 1 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1 X-2318-605-1 PANEL ASSY, SUB 2 2-583-939-01 SCREW (+B 2X4) 3 X-2179-691-1 LOCK ASSY 4 2-348-996-01 SCREW (+PTT 2.6X6), GROUND POINT 5 A-1551-001-A MAIN BOARD, COMPLETE (GT130) 5 A-1553-701-A MAIN BOARD, COMPLETE (GT280/GT280S/GT282S) 5 A-1553-836-A MAIN BOARD, COMPLETE 5 A-1553-851-A MAIN BOARD, COMPLETE (GT180) 6 1-833-974-31 CONNECTION CORD FOR AUTOMOBILE (POWER) FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A #1 7-685-792-09 SCREW +PTT 2.6X6 (S) #2 7-685-790-01 SCREW +PTT 2.6X4 (S) #3 7-685-793-09 SCREW +PTT 2.6X8 (S) #4 7-685-794-09 SCREW +PTT 2.6X10 (S) #5 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT #6 7-621-284-40 SCREW +P 2.6X10 28

5-2. FRONT PANEL SECTION 59 58 RE901 59 57 61 (KEY board) J901 56 LCD901 55 54 53 52 51 60 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 X-2318-582-1 BUTTON ASSY (S) (EXCEPT GT130/GT180) 51 X-2319-089-1 BUTTON ASSY (S) (GT130/GT180) 52 3-251-320-01 EMBLEM (NO. 2.5), SONY 53 X-2318-596-1 PANEL (SV) ASSY, FRONT (GT130) 53 X-2319-085-1 PANEL (SV) ASSY, FRONT (GT280) 57 3-398-493-01 ILLUMINATOR (LCD) 58 3-299-875-01 PANEL, BACK 59 3-250-543-91 SCREW (+B P-TITE M2) 60 A-1551-004-A PANEL COMPLETE ASSY, FRONT (GT130) 60 A-1553-690-A PANEL COMPLETE ASSY, FRONT (GT280) 53 X-2319-093-1 PANEL (SV) ASSY, FRONT (GT280S) 53 X-2319-095-1 PANEL (SV) ASSY, FRONT (GT282S) 53 X-2319-096-1 PANEL (SV) ASSY, FRONT 53 X-2319-100-1 PANEL (SV) ASSY, FRONT (GT180) 54 X-2318-581-1 KNOB (VOL) (SV) ASSY (GT280/GT280S/GT282S) 54 X-2318-608-1 KNOB (VOL) (SV) ASSY (GT130/GT180/GT230) 55 2-349-626-01 SPRING (RELEASE) 56 1-780-659-11 CONNECTOR (RUBBER) 60 A-1553-822-A PANEL COMPLETE ASSY, FRONT (GT280S) 60 A-1553-831-A PANEL COMPLETE ASSY, FRONT (GT282S) 60 A-1553-838-A PANEL COMPLETE ASSY, FRONT 60 A-1553-856-A PANEL COMPLETE ASSY, FRONT (GT180) 61 X-2186-697-1 CASE ASSY (for FRONT PANEL) (GT180/GT280/GT280S/GT282S) J901 1-822-148-11 SMALL TYPE JACK (VERTICAL) (AUX) LCD901 1-802-746-11 DISPLAY PANEL, LIQUID CRYSTAL RE901 1-479-902-32 ENCODER, ROTARY (PUSH SELECT/VOLUME) 29

5-3. CD MECHANISM SECTION (MG-101L-188/C) 101 102 #7 #7 103 105 104 107 106 106 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 101 A-1283-704-A MECHANICAL BLOCK ASSY (08) 102 A-1283-705-A DAXEV08//C 0 103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A) 104 2-626-869-21 SCREW (M2X3), SERRATION 105 3-348-998-31 SCREW (M1.4X2.5), TAPPING, PAN 106 3-352-758-31 SCREW (M1.7X2.5), TOOTHED LOCK 107 A-1542-217-A SERVO BOARD, COMPLETE #7 7-627-000-00 SCREW, PRECISION +P 1.7X2.2 TYPE3 30

SECTION 6 KEY ELECTRICAL PARTS LIST Note: Due to standardization, replacements in the parts list may be different from the parts specifi ed in the diagrams or the components used on the set. -XX and -X mean standardized parts, so they may have some difference from the original one. Items marked * are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. CAPACITORS uf: μf COILS uh: μh RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-fi lm resistor. F: nonflammable SEMICONDUCTORS In each case, u: μ, for example: ua.. : μa.., upa.., μpa.., upb.. : μpb.., upc.., μpc.., upd.. : μpd.. When indicating parts by reference number, please include the board. The components identifi ed by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specifi ed. Les composants identifi és par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifi é. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark KEY BOARD ********** < LIQUID CRYSTAL DISPLAY > LCD901 1-802-746-11 DISPLAY PANEL, LIQUID CRYSTAL 1-780-659-11 CONNECTOR (RUBBER) 3-398-493-01 ILLUMINATOR (LCD) < DIODE > < CAPACITOR > C921 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C922 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C971 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V (EXCEPT GT130/GT180) C981 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C983 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C984 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C986 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C987 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C990 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C999 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V < CONNECTOR > CN901 1-819-758-12 PLUG, CONNECTOR 15P < DIODE > D903 6-501-782-01 DIODE MAZ8180GMLS0 D981 6-501-730-01 DIODE MAZ8051GMLS0 D982 6-501-817-01 DIODE MA2J1110GLS0 D985 6-501-743-01 DIODE MAZ8068GMLS0 D986 6-501-743-01 DIODE MAZ8068GMLS0 D991 6-501-743-01 DIODE MAZ8068GMLS0 D992 6-501-743-01 DIODE MAZ8068GMLS0 D993 6-501-743-01 DIODE MAZ8068GMLS0 D994 6-501-743-01 DIODE MAZ8068GMLS0 (EXCEPT GT130/GT180) D998 1-216-295-11 SHORT CHIP 0 < JUMPER RESISTOR > FB903 1-216-295-11 SHORT CHIP 0 < IC > IC901 6-710-047-01 IC LC75836WH-US-E IC971 6-600-629-01 IC RS-470 (IR) (EXCEPT GT130/GT180) < JACK > J901 1-822-148-11 SMALL TYPE JACK (VERTICAL) (AUX) LED931 6-501-339-01 LED NESW505CT-AST (LCD BACK LIGHT) LED941 8-719-053-09 LED SML-310VTT86 (EQ3) LED941 8-719-078-21 LED SML-310PTT86 (EQ3) LED944 8-719-053-09 LED SML-310VTT86 (CD INDICATOR) LED944 8-719-078-21 LED SML-310PTT86 (CD INDICATOR) LED951 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION) LED951 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION) LED952 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION) LED953 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION) LED982 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION) LED1951 8-719-078-21 LED1952 8-719-078-21 LED SML-310PTT86 (RING ILLUMINATION) LED SML-310PTT86 (RING ILLUMINATION) < SWITCH > LSW901 1-786-805-13 SWITCH, TACTILE (WITH LED) (Z) LSW901 1-786-806-13 SWITCH, TACTILE (WITH LED) (Z) LSW902 1-786-805-13 SWITCH, TACTILE (WITH LED) (OFF) LSW902 1-786-806-13 SWITCH, TACTILE (WITH LED) (OFF) LSW903 1-786-805-13 SWITCH, TACTILE (WITH LED) (SOURCE) LSW903 1-786-806-13 SWITCH, TACTILE (WITH LED) (SOURCE) LSW904 1-786-805-13 SWITCH, TACTILE (WITH LED) (MODE) LSW904 1-786-806-13 SWITCH, TACTILE (WITH LED) (MODE) LSW905 1-786-805-13 SWITCH, TACTILE (WITH LED) (BTM) LSW905 1-786-806-13 SWITCH, TACTILE (WITH LED) (BTM) LSW906 1-786-805-13 SWITCH, TACTILE (WITH LED) (1) (GT130/GT180) 31

KEY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark LSW906 1-786-805-13 SWITCH, TACTILE (WITH LED) (1/ALBUM ) (GT280/GT280S/GT282S) LSW906 1-786-806-13 SWITCH, TACTILE (WITH LED) (1/ALBUM ) LSW907 1-786-805-13 SWITCH, TACTILE (WITH LED) (2) (GT130/GT180) LSW907 1-786-805-13 SWITCH, TACTILE (WITH LED) (2/ALBUM +) (GT280/GT280S/GT282S) LSW907 1-786-806-13 SWITCH, TACTILE (WITH LED) (2/ALBUM +) LSW908 1-786-805-13 SWITCH, TACTILE (WITH LED) (3/REP) LSW908 1-786-806-13 SWITCH, TACTILE (WITH LED) (3/REP) LSW909 1-786-805-13 SWITCH, TACTILE (WITH LED) (4/SHUF) LSW909 1-786-806-13 SWITCH, TACTILE (WITH LED) (4/SHUF) LSW910 1-786-805-13 SWITCH, TACTILE (WITH LED) (5) LSW910 1-786-806-13 SWITCH, TACTILE (WITH LED) (5) LSW911 1-786-805-13 SWITCH, TACTILE (WITH LED) (6/PAUSE) LSW911 1-786-806-13 SWITCH, TACTILE (WITH LED) (6/PAUSE) LSW912 1-786-805-13 SWITCH, TACTILE (WITH LED) (DSPL) (GT130/GT180) LSW912 1-786-805-13 SWITCH, TACTILE (WITH LED) (DSPL/SCRL) (GT280/GT280S/GT282S) R934 1-216-822-11 METAL CHIP 1.2K 5% 1/10W R941 1-216-807-11 METAL CHIP 68 5% 1/10W R941 1-216-809-11 METAL CHIP 100 5% 1/10W R942 1-216-807-11 METAL CHIP 68 5% 1/10W R942 1-216-809-11 METAL CHIP 100 5% 1/10W R943 1-216-811-11 METAL CHIP 150 5% 1/10W R943 1-216-812-11 METAL CHIP 180 5% 1/10W R944 1-216-810-11 METAL CHIP 120 5% 1/10W R944 1-216-811-11 METAL CHIP 150 5% 1/10W R945 1-216-811-11 METAL CHIP 150 5% 1/10W R945 1-216-812-11 METAL CHIP 180 5% 1/10W R946 1-216-027-00 METAL CHIP 120 5% 1/10W R946 1-216-029-00 METAL CHIP 150 5% 1/10W R947 1-216-811-11 METAL CHIP 150 5% 1/10W R947 1-216-812-11 METAL CHIP 180 5% 1/10W LSW912 1-786-806-13 SWITCH, TACTILE (WITH LED) (DSPL/SCRL) LSW913 1-786-805-13 SWITCH, TACTILE (WITH LED) (> M SEEK+) LSW913 1-786-806-13 SWITCH, TACTILE (WITH LED) (> M SEEK+) LSW914 1-786-805-13 SWITCH, TACTILE (WITH LED) (. m SEEK ) LSW914 1-786-806-13 SWITCH, TACTILE (WITH LED) (. m SEEK ) < TRANSISTOR > Q931 8-729-027-44 TRANSISTOR DTC114TKA-T146 Q932 6-551-444-01 TRANSISTOR RT1N436C-TP-1 < RESISTOR > R901 1-216-820-11 METAL CHIP 820 5% 1/10W R902 1-216-821-11 METAL CHIP 1K 5% 1/10W R903 1-216-821-11 METAL CHIP 1K 5% 1/10W R904 1-216-822-11 METAL CHIP 1.2K 5% 1/10W R905 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R907 1-216-820-11 METAL CHIP 820 5% 1/10W R908 1-216-821-11 METAL CHIP 1K 5% 1/10W R909 1-216-821-11 METAL CHIP 1K 5% 1/10W R910 1-216-822-11 METAL CHIP 1.2K 5% 1/10W R911 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R912 1-216-824-11 METAL CHIP 1.8K 5% 1/10W R913 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R914 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R915 1-216-828-11 METAL CHIP 3.9K 5% 1/10W R921 1-216-295-11 SHORT CHIP 0 R922 1-216-295-11 SHORT CHIP 0 R931 1-216-812-11 METAL CHIP 180 5% 1/10W R932 1-216-812-11 METAL CHIP 180 5% 1/10W R933 1-216-812-11 METAL CHIP 180 5% 1/10W R948 1-216-810-11 METAL CHIP 120 5% 1/10W R948 1-216-811-11 METAL CHIP 150 5% 1/10W R949 1-216-811-11 METAL CHIP 150 5% 1/10W R949 1-216-812-11 METAL CHIP 180 5% 1/10W R950 1-216-810-11 METAL CHIP 120 5% 1/10W R950 1-216-811-11 METAL CHIP 150 5% 1/10W R951 1-216-807-11 METAL CHIP 68 5% 1/10W R951 1-216-809-11 METAL CHIP 100 5% 1/10W R952 1-216-807-11 METAL CHIP 68 5% 1/10W R952 1-216-809-11 METAL CHIP 100 5% 1/10W R953 1-216-811-11 METAL CHIP 150 5% 1/10W R953 1-216-812-11 METAL CHIP 180 5% 1/10W R954 1-216-810-11 METAL CHIP 120 5% 1/10W R954 1-216-811-11 METAL CHIP 150 5% 1/10W R971 1-216-809-11 METAL CHIP 100 5% 1/10W R971 1-216-811-11 METAL CHIP 150 5% 1/10W R972 1-216-809-11 METAL CHIP 100 5% 1/10W R972 1-216-810-11 METAL CHIP 120 5% 1/10W 32

KEY MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R974 1-216-809-11 METAL CHIP 100 5% 1/10W (EXCEPT GT130/GT180) R975 1-216-809-11 METAL CHIP 100 5% 1/10W (EXCEPT GT130/GT180) R977 1-216-809-11 METAL CHIP 100 5% 1/10W R978 1-216-809-11 METAL CHIP 100 5% 1/10W R979 1-216-809-11 METAL CHIP 100 5% 1/10W R981 1-216-811-11 METAL CHIP 150 5% 1/10W R982 1-216-811-11 METAL CHIP 150 5% 1/10W R984 1-216-821-11 METAL CHIP 1K 5% 1/10W R985 1-216-821-11 METAL CHIP 1K 5% 1/10W R986 1-216-821-11 METAL CHIP 1K 5% 1/10W R987 1-216-857-11 METAL CHIP 1M 5% 1/10W R988 1-216-840-11 METAL CHIP 39K 5% 1/10W R992 1-216-864-11 SHORT CHIP 0 R1971 1-216-811-11 METAL CHIP 150 5% 1/10W R1972 1-216-810-11 METAL CHIP 120 5% 1/10W < ROTARY ENCODER > C25 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C26 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C27 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C28 1-126-947-11 ELECT 47uF 20% 35V C151 1-126-960-11 ELECT 1uF 20% 50V C152 1-126-960-11 ELECT 1uF 20% 50V C153 1-126-961-11 ELECT 2.2uF 20% 50V C154 1-137-712-11 CERAMIC CHIP 4700PF 20% 250V C155 1-137-712-11 CERAMIC CHIP 4700PF 20% 250V C157 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C301 1-124-248-00 ELECT 22uF 20% 25V C302 1-124-584-00 ELECT 100uF 20% 10V C305 1-124-584-00 ELECT 100uF 20% 10V C306 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C308 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C309 1-164-739-11 CERAMIC CHIP 560PF 5% 50V C310 1-164-739-11 CERAMIC CHIP 560PF 5% 50V C312 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C343 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C401 1-126-947-11 ELECT 47uF 20% 35V RE901 1-479-902-32 ENCODER, ROTARY (PUSH SELECT/VOLUME) < SWITCH > S901 1-786-653-11 SWITCH, TACTILE (EQ3) ************************************************************* A-1551-001-A A-1553-701-A A-1553-836-A A-1553-851-A MAIN BOARD, COMPLETE (GT130) MAIN BOARD, COMPLETE (GT280/GT280S/GT282S) MAIN BOARD, COMPLETE MAIN BOARD, COMPLETE (GT180) ********************* 7-621-284-40 SCREW +P 2.6X10 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT 7-685-794-09 SCREW +PTT 2.6X10 (S) < CAPACITOR > C1 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C2 1-162-907-11 CERAMIC CHIP 2PF 0.25PF 50V (EXCEPT GT130/GT230) C3 1-162-909-11 CERAMIC CHIP 4PF 0.25PF 50V (EXCEPT GT130/GT230) C5 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C6 1-162-914-11 CERAMIC CHIP 9PF 0.5PF 50V (GT130/GT230) C6 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V (EXCEPT GT130/GT230) C7 1-162-911-11 CERAMIC CHIP 6PF 0.5PF 50V C8 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C9 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C12 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V C13 1-100-742-11 CERAMIC CHIP 2.2uF 20% 10V C16 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V C17 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C18 1-162-916-11 CERAMIC CHIP 12PF 5% 50V C19 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C20 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C21 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C22 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C23 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C24 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C404 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C405 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C406 1-126-160-11 ELECT 1uF 20% 50V C407 1-126-160-11 ELECT 1uF 20% 50V C408 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V C409 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V C412 1-126-934-11 ELECT 220uF 20% 16V C413 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C431 1-126-964-11 ELECT 10uF 20% 50V C432 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C435 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C441 1-126-964-11 ELECT 10uF 20% 50V C442 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C445 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C451 1-126-964-11 ELECT 10uF 20% 50V C452 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C454 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C455 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C461 1-126-964-11 ELECT 10uF 20% 50V C462 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C464 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C465 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C471 1-126-964-11 ELECT 10uF 20% 50V C479 1-124-589-11 ELECT 47uF 20% 16V C481 1-126-964-11 ELECT 10uF 20% 50V C501 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C502 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V (GT280/GT280S/GT282S) C503 1-104-665-11 ELECT 100uF 20% 25V C504 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C507 1-162-918-11 CERAMIC CHIP 18PF 5% 50V C508 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C509 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C510 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C512 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C513 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C514 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C519 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C520 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C521 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C522 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V 33

MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C523 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C551 1-115-416-11 CERAMIC CHIP 0.001uF 5% 25V C601 1-112-302-11 ELECT 3300uF 20% 16V C602 1-165-319-11 CERAMIC CHIP 0.1uF 50V C617 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V D719 6-501-782-01 DIODE MAZ8180GMLS0 D753 6-500-522-01 DIODE 10EDB40-TA1B2 D754 6-500-522-01 DIODE 10EDB40-TA1B2 D755 6-500-522-01 DIODE 10EDB40-TA1B2 D756 6-500-522-01 DIODE 10EDB40-TA1B2 C618 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C622 1-126-926-11 ELECT 1000uF 20% 10V C623 1-126-926-11 ELECT 1000uF 20% 10V C631 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V C632 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V C681 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C682 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C683 1-124-261-00 ELECT 10uF 20% 50V C705 1-162-918-11 CERAMIC CHIP 18PF 5% 50V (EXCEPT GT130/GT180) C706 1-162-918-11 CERAMIC CHIP 18PF 5% 50V C707 1-162-918-11 CERAMIC CHIP 18PF 5% 50V C708 1-162-918-11 CERAMIC CHIP 18PF 5% 50V C709 1-162-918-11 CERAMIC CHIP 18PF 5% 50V C719 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C750 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V C751 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V C752 1-124-589-11 ELECT 47uF 20% 16V C753 1-128-551-11 ELECT 22uF 20% 63V C754 1-124-257-00 ELECT 2.2uF 20% 50V C755 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C756 1-216-864-11 SHORT CHIP 0 C758 1-124-261-00 ELECT 10uF 20% 50V C761 1-126-176-11 ELECT 220uF 20% 10V C763 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V C764 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V C765 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V C769 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V C770 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V C771 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C774 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V C775 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V C776 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V < CONNECTOR > * CN351 1-564-710-11 PIN, CONNECTOR (SMALL TYPE) 8P CN601 1-774-701-21 PIN, CONNECTOR 16P CN701 1-819-773-14 SOCKET, CONNECTOR 15P CNP301 1-820-611-11 CONNECTOR, BOARD TO BOARD 28P < DIODE > D153 8-719-978-33 DIODE DTZ-TT11-6.8B D479 6-501-817-01 DIODE MA2J1110GLS0 D502 6-502-131-01 DIODE LRB751V-40T1G (EXCEPT GT130/GT180) D510 6-501-656-01 DIODE LBAT54ALT1G D511 6-500-335-01 DIODE MC2838-T112-1 D512 6-501-654-01 DIODE LBAT54CLT1G D580 6-501-747-01 DIODE MAZ8075GMLS0 D581 6-501-782-01 DIODE MAZ8180GMLS0 D601 6-501-571-01 DIODE 1N5404-C311-3 D617 6-501-782-01 DIODE MAZ8180GMLS0 D701 6-501-170-01 DIODE UDZW-TE17-6.8B D702 6-501-170-01 DIODE UDZW-TE17-6.8B D703 6-501-170-01 DIODE UDZW-TE17-6.8B D704 6-501-170-01 DIODE UDZW-TE17-6.8B D759 6-500-522-01 DIODE 10EDB40-TA1B2 D760 6-500-522-01 DIODE 10EDB40-TA1B2 D761 6-500-522-01 DIODE 10EDB40-TA1B2 D762 6-500-522-01 DIODE 10EDB40-TA1B2 < FERRITE BEAD > FB1 1-216-864-11 SHORT CHIP 0 (EXCEPT GT130/GT230) FB1 1-400-334-21 FERRITE, EMI (SMD) (1608) (GT130/GT230) FB2 1-216-864-11 SHORT CHIP 0 (EXCEPT GT130/GT230) FB2 1-400-334-21 FERRITE, EMI (SMD) (1608) (GT130/GT230) FB304 1-469-777-21 INDUCTOR, FERRITE BEAD FB308 1-414-233-22 INDUCTOR, FERRITE BEAD FB309 1-216-864-11 SHORT CHIP 0 FB311 1-469-777-21 INDUCTOR, FERRITE BEAD FB312 1-400-382-11 FERRITE, EMI (SMD) (1608) FB401 1-400-334-21 FERRITE, EMI (SMD) (1608) FB402 1-400-334-21 FERRITE, EMI (SMD) (1608) FB561 1-469-777-21 INDUCTOR, FERRITE BEAD (GT280/GT280S/GT282S) FB562 1-469-777-21 INDUCTOR, FERRITE BEAD (GT280/GT280S/GT282S) FB563 1-469-777-21 INDUCTOR, FERRITE BEAD (GT280/GT280S/GT282S) FB604 1-216-295-11 SHORT CHIP 0 < FUSE > FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A < IC > IC1 6-712-929-01 IC TEF6607T/V3/S470,518 IC401 6-713-080-11 IC BD3447AFV-E2 IC501 6-808-271-02 IC R5F3640DDA07FA IC602 6-709-458-01 IC XC61CN2802NR IC681 6-711-670-01 IC XC6218P332PR IC750 6-705-359-02 IC TDA8588AJ/N2/R1 < JACK > J1 1-815-185-13 JACK (ANTENNA) J330 1-774-698-11 JACK, PIN 2P (AUDIO OUT REAR/SUB) J561 1-566-822-41 JACK (REMOTE IN) (GT280/GT280S/GT282S) < JUMPER RESISTOR > JC151 1-216-864-11 SHORT CHIP 0 JC301 1-216-864-11 SHORT CHIP 0 JC302 1-216-864-11 SHORT CHIP 0 JC303 1-216-864-11 SHORT CHIP 0 JC501 1-216-864-11 SHORT CHIP 0 (EXCEPT GT130/GT180) JC502 1-216-864-11 SHORT CHIP 0 JC503 1-216-864-11 SHORT CHIP 0 JC521 1-216-864-11 SHORT CHIP 0 JC533 1-216-864-11 SHORT CHIP 0 JC754 1-216-296-11 SHORT CHIP 0 JC755 1-216-296-11 SHORT CHIP 0 34

MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < COIL > L1 1-414-180-51 INDUCTOR 3.3uH L2 1-414-142-11 INDUCTOR 1uH (EXCEPT GT130/GT230) L2 1-410-501-61 INDUCTOR 2.2uH (GT130/GT230) L3 1-412-698-21 INDUCTOR 0.47uH (EXCEPT GT130/GT230) L4 1-410-503-11 INDUCTOR 3.3uH (EXCEPT GT130/GT230) L6 1-457-644-11 COIL (FM MIX) L7 1-481-285-51 INDUCTOR 560uH L8 1-481-285-51 INDUCTOR 560uH L151 1-216-295-11 SHORT CHIP 0 L601 1-456-617-11 COIL, CHOKE < TRANSISTOR > R471 1-216-813-11 METAL CHIP 220 5% 1/10W R472 1-216-833-11 METAL CHIP 10K 5% 1/10W R479 1-216-805-11 METAL CHIP 47 5% 1/10W R481 1-216-813-11 METAL CHIP 220 5% 1/10W R482 1-216-833-11 METAL CHIP 10K 5% 1/10W R501 1-219-570-11 METAL CHIP 10M 5% 1/10W R502 1-216-821-11 METAL CHIP 1K 5% 1/10W R503 1-216-821-11 METAL CHIP 1K 5% 1/10W R504 1-218-871-11 METAL CHIP 10K 0.5% 1/10W R505 1-218-871-11 METAL CHIP 10K 0.5% 1/10W R506 1-216-845-11 METAL CHIP 100K 5% 1/10W R507 1-216-845-11 METAL CHIP 100K 5% 1/10W R508 1-216-849-11 METAL CHIP 220K 5% 1/10W R509 1-216-864-11 SHORT CHIP 0 R510 1-216-821-11 METAL CHIP 1K 5% 1/10W Q431 8-729-027-44 TRANSISTOR DTC114TKA-T146 Q441 8-729-027-44 TRANSISTOR DTC114TKA-T146 Q451 8-729-027-44 TRANSISTOR DTC114TKA-T146 Q461 8-729-027-44 TRANSISTOR DTC114TKA-T146 Q471 6-551-856-01 TRANSISTOR LTC614TKFP8T146 Q478 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q479 8-729-027-23 TRANSISTOR DTA114EKA-T146 Q481 6-551-856-01 TRANSISTOR LTC614TKFP8T146 Q580 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q581 8-729-038-28 TRANSISTOR RT1N441C-TP-1 Q582 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF Q631 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF < RESISTOR > R1 1-216-853-11 METAL CHIP 470K 5% 1/10W R2 1-216-853-11 METAL CHIP 470K 5% 1/10W R3 1-216-809-11 METAL CHIP 100 5% 1/10W (EXCEPT GT130/GT230) R3 1-400-334-21 FERRITE, EMI (SMD) (1608) (GT130/GT230) R4 1-216-864-11 SHORT CHIP 0 R5 1-216-864-11 SHORT CHIP 0 R6 1-216-843-11 METAL CHIP 68K 5% 1/10W R10 1-216-839-11 METAL CHIP 33K 5% 1/10W R11 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R12 1-216-009-11 METAL CHIP 22 5% 1/10W R13 1-216-809-11 METAL CHIP 100 5% 1/10W R14 1-216-809-11 METAL CHIP 100 5% 1/10W R151 1-216-817-11 METAL CHIP 470 5% 1/10W R152 1-216-817-11 METAL CHIP 470 5% 1/10W R153 1-216-834-11 METAL CHIP 12K 5% 1/10W R154 1-216-834-11 METAL CHIP 12K 5% 1/10W R155 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R301 1-216-821-11 METAL CHIP 1K 5% 1/10W R302 1-216-821-11 METAL CHIP 1K 5% 1/10W R401 1-216-797-11 METAL CHIP 10 5% 1/10W R413 1-216-864-11 SHORT CHIP 0 R414 1-216-864-11 SHORT CHIP 0 R431 1-216-821-11 METAL CHIP 1K 5% 1/10W R432 1-216-833-11 METAL CHIP 10K 5% 1/10W R441 1-216-821-11 METAL CHIP 1K 5% 1/10W R442 1-216-833-11 METAL CHIP 10K 5% 1/10W R451 1-216-821-11 METAL CHIP 1K 5% 1/10W R452 1-216-833-11 METAL CHIP 10K 5% 1/10W R461 1-216-821-11 METAL CHIP 1K 5% 1/10W R462 1-216-833-11 METAL CHIP 10K 5% 1/10W R511 1-216-821-11 METAL CHIP 1K 5% 1/10W R512 1-216-821-11 METAL CHIP 1K 5% 1/10W R513 1-216-845-11 METAL CHIP 100K 5% 1/10W R514 1-216-845-11 METAL CHIP 100K 5% 1/10W R519 1-216-845-11 METAL CHIP 100K 5% 1/10W R521 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R522 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R523 1-216-845-11 METAL CHIP 100K 5% 1/10W R526 1-216-845-11 METAL CHIP 100K 5% 1/10W R528 1-216-845-11 METAL CHIP 100K 5% 1/10W R529 1-216-845-11 METAL CHIP 100K 5% 1/10W R530 1-216-845-11 METAL CHIP 100K 5% 1/10W R531 1-216-845-11 METAL CHIP 100K 5% 1/10W R532 1-216-845-11 METAL CHIP 100K 5% 1/10W R533 1-216-845-11 METAL CHIP 100K 5% 1/10W R534 1-216-833-11 METAL CHIP 10K 5% 1/10W R535 1-216-833-11 METAL CHIP 10K 5% 1/10W R536 1-216-833-11 METAL CHIP 10K 5% 1/10W R537 1-216-845-11 METAL CHIP 100K 5% 1/10W (EXCEPT GT130/GT230) R538 1-216-845-11 METAL CHIP 100K 5% 1/10W (GT130/GT230) R539 1-216-845-11 METAL CHIP 100K 5% 1/10W R540 1-216-845-11 METAL CHIP 100K 5% 1/10W R541 1-216-845-11 METAL CHIP 100K 5% 1/10W R542 1-216-821-11 METAL CHIP 1K 5% 1/10W R543 1-216-821-11 METAL CHIP 1K 5% 1/10W R546 1-216-845-11 METAL CHIP 100K 5% 1/10W (EXCEPT GT130/GT230) R547 1-216-821-11 METAL CHIP 1K 5% 1/10W R550 1-216-845-11 METAL CHIP 100K 5% 1/10W R551 1-216-845-11 METAL CHIP 100K 5% 1/10W (GT130/GT230) R556 1-216-833-11 METAL CHIP 10K 5% 1/10W R558 1-216-821-11 METAL CHIP 1K 5% 1/10W R561 1-216-845-11 METAL CHIP 100K 5% 1/10W R563 1-216-845-11 METAL CHIP 100K 5% 1/10W R565 1-216-845-11 METAL CHIP 100K 5% 1/10W R566 1-216-845-11 METAL CHIP 100K 5% 1/10W R567 1-216-845-11 METAL CHIP 100K 5% 1/10W R570 1-216-817-11 METAL CHIP 470 5% 1/10W R574 1-216-845-11 METAL CHIP 100K 5% 1/10W (EXCEPT GT130/GT230) R575 1-216-845-11 METAL CHIP 100K 5% 1/10W (GT130/GT230) R578 1-216-821-11 METAL CHIP 1K 5% 1/10W 35

MAIN SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R582 1-216-821-11 METAL CHIP 1K 5% 1/10W R583 1-216-821-11 METAL CHIP 1K 5% 1/10W R584 1-216-849-11 METAL CHIP 220K 5% 1/10W R585 1-216-849-11 METAL CHIP 220K 5% 1/10W R601 1-216-845-11 METAL CHIP 100K 5% 1/10W R631 1-216-073-00 METAL CHIP 10K 5% 1/10W R632 1-216-841-11 METAL CHIP 47K 5% 1/10W R633 1-216-841-11 METAL CHIP 47K 5% 1/10W R634 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R635 1-216-073-00 METAL CHIP 10K 5% 1/10W R636 1-216-845-11 METAL CHIP 100K 5% 1/10W R661 1-216-821-11 METAL CHIP 1K 5% 1/10W R662 1-216-833-11 METAL CHIP 10K 5% 1/10W R663 1-216-821-11 METAL CHIP 1K 5% 1/10W R664 1-216-833-11 METAL CHIP 10K 5% 1/10W R671 1-216-809-11 METAL CHIP 100 5% 1/10W R672 1-216-809-11 METAL CHIP 100 5% 1/10W R673 1-218-871-11 METAL CHIP 10K 0.5% 1/10W R674 1-216-845-11 METAL CHIP 100K 5% 1/10W R675 1-216-821-11 METAL CHIP 1K 5% 1/10W R676 1-216-821-11 METAL CHIP 1K 5% 1/10W R677 1-216-864-11 SHORT CHIP 0 R679 1-216-821-11 METAL CHIP 1K 5% 1/10W R690 1-216-845-11 METAL CHIP 100K 5% 1/10W R692 1-216-845-11 METAL CHIP 100K 5% 1/10W (EXCEPT GT130/GT180) ACCESSORIES ************ 1-479-077-13 REMOTE COMMANDER (RM-X151) (GT230/GT280/GT280S/GT282S) 2-548-729-01 LID, BATTERY CASE (for RM-X151) (GT230/GT280/GT280S/GT282S) 4-000-121-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH, SPANISH) (GT130/GT230) 4-000-121-22 MANUAL, INSTRUCTION (ENGLISH,SPANISH) (GT180/GT280/GT280S/GT282S) 4-000-126-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH, FRENCH,SPANISH) (GT130/GT230) 4-000-126-22 MANUAL, INSTRUCTION, INSTALL (ENGLISH, SPANISH) (GT180/GT280/GT280S/GT282S) X-2186-697-1 CASE ASSY (for FRONT PANEL) (GT180/GT280/GT280S/GT282S) ************************************************************* PARTS FOR INSTALLATION AND CONNECTIONS ************************************** 151 X-2179-430-2 FRAME ASSY, FITTING 152 3-398-492-01 COLLAR 153 3-876-674-01 KEY (FRAME) 154 1-833-974-31 CONNECTION CORD FOR AUTOMOBILE (POWER) 155 A-1082-993-A SCREW ASSY (BS4), FITTING (GT180/GT280/GT280S/GT282S) R693 1-216-845-11 METAL CHIP 100K 5% 1/10W (GT130/GT180) R752 1-216-811-11 METAL CHIP 150 5% 1/10W R756 1-216-841-11 METAL CHIP 47K 5% 1/10W 156 3-259-776-01 SCREW (+K 5X8 TP) 151 152 153 < SWITCH > S502 1-571-478-11 SWITCH, SLIDE (FREQUENCY SELECTOR) (EXCEPT GT130/GT230) 2 < SURGE ABSORBER > VDR1 1-805-043-11 ABSORBER, CHIP SURGE 154 155 < VIBRATOR > X1 1-814-161-11 QUARTZ CRYSTAL UNIT (4MHz) X501 1-814-075-21 VIBRATOR, CERAMIC (11.06MHz) X502 1-767-317-11 VIBRATOR, CRYSTAL (32.768kHz) ************************************************************* 156 A-1542-217-A SERVO BOARD, COMPLETE ********************** ************************************************************* 4 MISCELLANEOUS ************** 6 1-833-974-31 CONNECTION CORD FOR AUTOMOBILE (POWER) 0 103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A) ************************************************************* 36

MEMO 37

REVISION HISTORY Checking the version allows you to jump to the revised page. Also, clicking the version at the top of the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 1.0 2008.08 New