08-07-2015 i3hawm E(BASIC) MOUNTING INSTRUCTIONS
1. INDEX 1. Index 3 2. Important safety instructions 4 3. Maximum loads 7 4. Different configuraties 8 5. Part list i3hawm-e (basic) 9 6. Preparing frame 10 7. Installation on wall 12 8. Installation i3board 15 9. Installation SMART BOARD 25 i3hawm Height adjustable wall-mount 3
2. IMPORTANT SAFETY INSTRUCTIONS: Instruct all users of the board! Never place any object under the board For safety reasons,the board must be able to reach its lowest position at all times. Note that when the i3hawm-e (Basic) system re-initialises itself,it will run all the way down to its lowest 1 possible position. 2 distance r 650 m2 Safety settings Refer to the document Safety instructions to set anti-collision, stroke-lenght and initialisation time of the system. 4 i3hawm-e (Basic)
Installation This installation is intented to be executed by qualified personnel only. 2 persons are needed to do the job. Depending on local circumstances (wall conditions etc), it may be necessary to substitute the supplied general purpose hardware. Installers must be familiar with mechanical construction and electronic installations. Check this first! 115V 230V Locally acuire matching power chord (c13 or c14 connector) i3hawm Height adjustable wall-mount 5
Cable management Secure the cables to frame with cable ties, allow a cable loop of >650mm. Protect cables with rubber sleeves. Make sure all cables enter/exit the frame through the cable guide openings. Users Install the projector by following the installation guide of the projector This device is not intented to be used by persons (including children) with physical,sensory or mental disabilities or lack of experience and/or knowledge,unless, they are supervised or received instructions on how to use the device. Children should be supervised to ensure that they do not play with the device Please keep this manual for later reference. 6 i3hawm-e (Basic)
3. MAXIMUM LOADS distance r m1 650 m2 Usage: duty cycle 10% 6min per hour or 2 min continuous at full load. Actuator 1200 N Range (adjustable) 650 mm Power supply 230 V/50Hz r max. 1200 mm m1 (r<600mm) max. 15 kg max. 33 lbs m1 (r>600mm) max. 12 kg max. 26 lbs m2 max. 80 kg max. 176 lbs m1 + m2 max. 95 kg max. 209 lbs* *in case of Piëzo actuator max. 55 kg max. 121 lbs i3hawm Height adjustable wall-mount 7
4. DIFFERENT CONFIGURATIONS See drilling instructions that can be downloaded from http://www.i3-learning.com/i3hawm-templates 5. PART LIST i3hawm-e (Basic) Part List Id V G Number Q Description info 3.1 BS/A44200X 1 Frame RAL7021 3.2 BS/L45100X 2 Vertical support adapter profile 3.3 BS/L45200X 2 Horizontal support adapter profile 1 Power cable Hardware Bag/List (BS/A446011 - frame i3hawm-e Basic) (1/5) Id V G Number Q Description info 6. PREPARING FRAME 3.4 22/050783 6 Cable protection 3.5 23/040332 4 Plug 10 3.6 23/040188 4 Lag bolt hex head 8x80 3.7 23/090273 4 Flange nut M5 3.8 23/040440 4 Screw pan head cross M5x40 3.9 23/090275 4 Flange nut M6 3.10 23/040358 4 Screw pan head cross M30 3.11 07/050546 4 Anti loss washer 23/040302 2 Plug 30 fixation control cable 23/040179 2 Screw countersunk head cross 4x40 fixation control cable 00/080004 4 Cable tie fixation cables 3.12 23/090411 2 Self drilling screw 4,2 x 32 8 i3hawm-e (Basic)
3.1 3.3 3.6 (4x) 3.7 (4x) 3.2 3.8 (4x) 3.12 3.4 () 3.11 (4x) 3.10 (4x) 3.9 (4x) 3.8 (4x) i3hawm Height adjustable wall-mount 9
6. PREPARING FRAME Place the frame horizontally Drill the holes in the upperplate, (checklist configurations) using the appropriate template Pre-install all the cables (power,vga etc) 6.1 Mount the support of the projector with: d Wi 87 Duo/I3 projector Hardware Bag (type A)/List (BS/A451011 - Projectorplate) Id V G Number Q Description info A.1 23/040192 4 Screw pan head crossm40 A.2 23/090275 4 Flange nut M6 Support i3projector A.2 4x A.1 4x I3 Boards/I3 projector Hardware BS/A511011 Id VG Number Q Description Info I.1 23/090347 3 Screw M16 23/090275 5 Nut M6 I.3 23/090404 2 Nut M6 low I.1 3x Note: In case of i3board (3th generation): preinstall first the board s adapter bracket (supplied with the board) to the horizontal support adapter profile before installing all the support adapter profiles to the frame. Support i3board I.4 23/090421 2 Set screw M 30 I.5 07/090286 2 Spacer 6.3x15x15 I.6 15/050847 2 Spacer 15x5 I.7 23/090252 2 Spacer I.8 23/090408 2 Screw M4X20 I.1 3x 5x 10 i3hawm-e (Basic)
In case of i3board (4th generation): preinstall as shown I.9 I.4 I.9 1100 I.4 I.9 I.10 I.4 I.9 I.9 I.10 I.4 I.9 I.4 I.11 300 1100 I.11 I.4 Hardware Bag (type B)/List (BS/A511011 - i3board) Id V G Number Q Description info 1.1 23/090347 3 Screw M6 x 16 1.2 23/090275 5 Nut M6 1.3 23/090404 2 Nut M6 low 1.4 23/090421 4 Set screw M6 x 30 1.5 07/090286 2 Spacer 6.3 x 15 x 15 1.6 15/050847 2 Spacer 6 x 15 x 5 1.7 23/090252 2 Spacer 1.8 23/090408 2 Screw M4 x 20 1.9 23/090432 6 Square nut M6 1.10 23/090430 2 Anti loss washer 6 x 30 x 3 1.11 23/090431 2 Anti loss washer 6 x 11 x 1,5 i3hawm Height adjustable wall-mount 11
6.2 Install the support adapter profiles to the frame. I.1 I3White board Wi 87 Duo/I3 projector 3x First the vertical ones and then the horizontal ones (See page 16-21 for bolt positions). 3.3 3.9 5x 3.11 Hardw Id J1 J2 J3 J4 4.1 5.1 3.7 3.6 (4x) 3.10 3.2 3.8 I.1 Note: Only for i3whiteboard s Wi / Wi Plus 3.12 3.4 () J.1 3x 5.1 1x J.2 3x 3.8 (4x) I.5 J.1 7. INSTALLATION ON WALL I.3 I.6 7.1 Solid wall Mount the frame against the wall minding the drilling pattern. (page 16-27) I.8 I.7 Work subtle! STWL-KIT 12 i3hawm-e (Basic)
7.2 Stud wall i3hawm-e (Basic) + VSV0003437 mounting kit stud wall E.5 E.4 (4x) E.1 E.3 (4x) E.6 E.2 E.7 Part list SCALE 1 : 5 Id V G Number Q Description info E.1 BS/L57400X 1 Support STWL-kit E.2 BS/L57300X 2 Hook STWL-kit Hardware Bag( type E)/List (BS/A576010 Stud Wall) Id V G Number Q Description info E.3 23/090387 4 Toggler M6 E.4 23/040192 4 Screw pan head cross M40 E.5 23/040161 2 Screw pan head cross 4,8x16 E.6 23/090298 2 Screw pan head cross M10 E.7 23/090384 2 Hammer nut M6 i3hawm Height adjustable wall-mount 13
Note: Mounting the studwall-kit Drill 2 holes ø 13mm in the plasterwall and make sure that one of them is in a steel stud. (Holes in the profile are positioned 15mm lower than those in the frame) 100 200 300 400 Fix the support to the wall with the 2 TOGGLER plugs and screws. Hang the frame on the support. Drill 2 holes ø 13mm below the frame, see drawing, also one in a steel stud Fix the 2 brackets to the bottom of the frame using bolts and hammer nuts. Fix the brackets to the wall be using TOGGLER plugs and bolts. Changeable Drill 2 holes ø 4mm through the holes of the support in the frame and fix them with screws 4,8x19mm SCALE 1 : 5 15 14 i3hawm-e (Basic)
8. INSTALLATION i3board Hang the board on the frame and fix the board. For i3board s (3th generation) I.3 I.5 I.4 For i3board s (4th generation) For i3whiteboard s Wi / Wi Plus I.3 I.5 I.4 i3hawm Height adjustable wall-mount 15
8.1 i3board (4TH GENERATION) / i3projector I3 Board /I3 projector L3502W- L3302FHD I.6 I.8 I.7 Support i3projector A.1 4x A.2 4x I.6 I.8 Hardware BS/A511011 Id VG Number Q Description Info I.1 23/090347 3 Screw M6 23/090275 6 Hex flange Nut M6 I.3 23/090404 2 Nut M6 low I.4 23/090421 6 Set screw M 30 I.5 07/090286 2 Spacer 6.3x15x15 I.6 15/050847 2 Spacer 15x5 I.7 23/090252 2 Spacer I.8 23/090408 2 Screw M4X20 I.9 23/090432 6 Square nut M6 I.10 23/090430 2 Anti loss washer 30x3 I.11 23/090431 2 Anti loss washer 11x1.5 I.9 I.9 I.7 I.4 I.6 16 i3hawm-e (Basic)
Mounting positions i3board s (4TH GENERATION) / i3projector Distance Y Distance Y Distance A(min. ceiling height) 2250(ideal viewplane,highest position) (*) 650 (adjustable) Distance B (drill patern) Distance X between top of profiles 650 26 Mounting positions i3board (04 series) Ceiling 500 (100" showed) Floor (*)= adapt the height according to local situation 1 DETAIL 1 1231 2150 Board Projector Distance A Distance B Distance X DistanceY ideal Viewplane i3board 8704 T10 3303W 2820mm 1995mm 510mm 80mm 2250mm i3board 8704 T10 L3502W 2785mm 1960mm 475mm 80mm 2250mm i3board10004 T10 3303W 2910mm 2085mm 600mm 80mm 2250mm i3board 10004 T10 L3302FHD 2830mm 2005mm 520mm 80mm 2250mm i3board 10004 T10 100" Duo L3502W 2870mm 2045mm 560mm 80mm 2250mm bolt position bolt position i3hawm Height adjustable wall-mount 17
8.2 i3board (3TH GENERATION) / i3projector I3 Boards/I3 projector 2402W-2802W Support i3board I.1 3x I.6 I.8 I.7 Support i3projector A.1 4x I.4 I.3 A.2 4x I.5 5x 5x Hardware BS/A511011 Id VG Number Q Description Info I.1 23/090347 3 Screw M16 23/090275 6 Nut M6 I.3 23/090404 2 Nut M6 low I.4 23/090421 6 Set screw M 30 I.5 07/090286 2 Spacer 6.3x15x15 I.6 15/050847 2 Spacer 15x5 I.7 23/090252 2 Spacer I.8 23/090408 2 Screw M4X20 I.9 23/090432 6 Square nut M6 I.10 23/090430 2 Anti loss washer 30x3 1.11 23/090431 2 Anti loss washer 11x1.5 I.1 I.3 I.4 I.6 I.8 I.7 I.5 18 i3hawm-e (Basic)
Mounting positions i3board s (3TH GENERATION) / i3projector Distance Y Distance Y 650 (adjustable) 2250(ideal viewplane,highest position) (*) Distance A(min. ceiling height) Distance B (drill patern) 64 Mounting positions i3board (03 series) Ceiling bolt position bolt position 1226 top of profiles between Distance X 1934 (87" showed) (*)= adapt the height according to local situation 500 Floor Board Projector Distance A Distance B Distance X DistanceY ideal Viewplane i3board 7703 T06 3303W 2810mm 1980mm 505mm 80mm 2250mm i3board 7703 T06 L3502W 2775mm 1945mm 470mm 80mm 2250mm i3board 8703 T06 3303W 2810mm 1980mm 505mm 80mm 2250mm i3board 8703 T06 L3502W 2775mm 1945mm 470mm 80mm 2250mm 1 DETAIL 1 650 i3hawm Height adjustable wall-mount 19
8.3 i3whiteboard Wi 87 Duo / i3projector I3White board Wi 87 Duo/I3 projector Hardware BS/A513010 Support i3projector A.2 4x Id VG Number Q Description Info J1 23/040347 3 Screw M16 J2 23/090275 3 Nut M6 Support i3board A.1 4x J3 23/090385 2 Screw M5x12 J4 23/090273 2 Nut M5 5.1 BS/L90100X 1 Pen tray holder I.1 3x 5x I.1 J.4 J.2 3x 4.1 J.1 3x I.3 5.1 1x I.4 I.5 5x I.5 J.3 I.6 J.1 I.3 J.2 I.4 J.3 J.4 I.6 I.7 I.8 I.8 I.7 20 i3hawm-e (Basic)
Mounting positions i3whiteboard Wi 87 Duo / i3projector Distance Y Distance Y DETAIL 1 Distance A(min. ceiling hight) 2251,022(ideal viewplane,highest position) (*) 650 (adjustable) Distance B (drill patern) 2810 74 Mounting positions i3whiteboard Wi 87" DUO Ceiling bolt position (*)= adapt the height according to local situation Floor Board Projector Distance A Distance B Distance X Distance Y ideal Viewplane i3whiteboard Wi 87" Duo 3303Wi 2800mm 1980mm 500mm 80mm 2250mm 1 1200 650 top of profiles between Distance X 1910 bolt position 500 i3hawm Height adjustable wall-mount 21
8.4 i3whiteboard Wi Plus 87 Duo / i3projector I3White board Wi PLUS Duo/I3 projector Support i3board I.1 3x J.3 I.6 I.7 I.8 Support i3projector A.1 4x J.4 J.1 3x I.3 5.1 1x A.2 4x J.2 3x I.4 I.5 4.1 5x 5x I.6 I.8 I.7 Hardware BS/A512011 Id VG Number Q Description Info J1 23/040347 3 Screw M16 J2 23/090275 3 Nut M6 J3 23/090385 2 Screw M5x12 J4 23/090273 2 Nut M5 4.1 BS/L 45400X 2 Vertical support Wi+ (1300mm) 5.1 BS/L90100X 1 Pen tray holder I.1 J.1 I.5 J.2 I.3 I.4 J.3 J.4 22 i3hawm-e (Basic)
Mounting positions i3whiteboard Wi Plus 87 Duo / i3projector Distance Y Distance Y Distance A(min. ceiling hight) 650 (adjustable) 2250(ideal viewplane,highest position) (*) 1300 Distance B (drill patern) 650 Distance X between top of profiles 74 Mounting positions i3whiteboard Wi PLUS DUO Ceiling bolt position 1910 bolt position 500 (*)= adapt the height according to local situation Floor Board Projector Distance A Distance B Distance X Distance Y ideal Viewplane I3WHITEBOARD Wi PLUS 87" 3303Wi 2810mm 2045mm 405mm 80mm 2250mm i3hawm Height adjustable wall-mount 23
24 i3hawm-e (Basic)
9. INSTALLATION SMART BOARD Mount the plastic bracket against the upper horizontal wall mount s adapter profile Support SMART BOARD C.1 (3x) Hardware BS/A471011 C.2 (3x) Id VG Number Q Description Info C.1 23/050968 3 Screw M5x20 C.2 23/090273 3 Nut M5 C.3 23/090296 2 Screw 1/4-20x/0.625 C.4 07/050546 2 Anti loss washer 3.3 Hardware Bag (type C)/List (BS/A471011 - SMART) Id V G Number Q Description info C.1 23/050968 3 Screw pan head cross M5x20 C.2 23/090273 3 Flange nut M5 C.3 23/090296 2 Hex socket button head 1/4-20x/0.625 C.4 07/050546 2 Anti loss washer C.3 SCALE 1 : 3 Use the standard SMART inserts C.3 60 C.4 140 i3hawm Height adjustable wall-mount 25
9.1 SMART BOARD M680 - M685 / i3projector SMART 685/i3-Projector Support i3projector A.2 (4x) A.1 (4x) Support SMART BOARD C.1 C.2 (3x) (3x) C.4 C.3 C.2 C.4 Hardware BS/A471011 Id VG Number Q Description Info C.1 23/050968 3 Screw M5x20 C.2 23/090273 3 Nut M5 C.3 23/090296 2 Screw 1/4-20x/0.625 C.4 07/050546 2 Anti loss washer C.1 C.3 26 i3hawm-e (Basic)
Mounting positions SMART BOARD M680 - M685 / i3projector Distance Y 1260 Distance B (drill patern) 132 Distance Y Mounting positions Smart M Boards Ceiling Distance A(min. ceiling height) 2250(ideal viewplane,highest position) (*) 650 (adjustable) Board Projector Distance A Distance B Distance X Distance Y ideal Viewplane SMART BOARD M 680 2402W/2802W 2870mm 2045mm 533mm 55mm (left) 2250mm SMART BOARD M 680 L3502W 2795mm 1970mm 458mm -80mm (right) 2250mm SMART BOARD M 685 2402W/2802W 2870mm 2045mm 533mm 55mm (left) 2250mm SMART BOARD M 685 L3502W 2795mm 1970mm 458mm -80mm (right) 2250mm bolt position bolt position 2 1 Distance X between top of profiles 650 44 1975 500 (M685 showed) Floor (*)= adapt the height according to local situation DETAIL 1 DETAIL 2 i3hawm Height adjustable wall-mount 27
9.2 SMART BOARD X880 - X885 / i3projector SMART 885/i3 PROJECTOR A2 (4x) Support i3projector A1 (4x) Support SMART BOARD C1 C2 (3x) (3x) C4 C3 Hardware BS/A471011 Id VG Number Q Description Info C.1 23/050968 3 Screw M5x20 C2 23/090273 3 Nut M5 C.3 23/090296 2 Screw 1/4-20x/0.625 C.4 07/050546 2 Anti loss washer C1 C2 C3 C4 28 i3hawm-e (Basic)
Mounting positions SMART BOARD X880 - X885 / i3projector 214 Distance Y Mounting positions Smart X Boards Ceiling Distance Y DETAIL 2 Distance A(min. ceiling height) 650 (adjustable) 2250(ideal viewplane,highest position) (*) 1300 Distance B (drill patern) Board Projector Distance A Distance B Distance X Distance Y ideal Viewplane SMART BOARD X880 2402W/2802W 2870mm 2045mm 555mm 55mm (left) 2250mm SMART BOARD X880 L3502W 2795mm 1970mm 480mm -80mm (right) 2250mm SMART BOARD X885 2402W/2802W 2870mm 2045mm 555mm 55mm (left) 2250mm SMART BOARD X885 L3502W 2795mm 1970mm 480mm -80mm (right) 2250mm bolt position bolt position 2 1 Distance X between top of profiles 650 44 1994 500 (X885 showed) Floor (*)= adapt the height according to local situation DETAIL 1 i3hawm Height adjustable wall-mount 29
30 i3hawm-e (Basic)
i3hawm Height adjustable wall-mount 31
AUTHORISED DISTRIBUTOR WWW.I3-TECHNOLOGIES.COM INFO@I3-TECHNOLOGIES.COM