Riverbed Steelhead Configure Hardware Client Whilst the above information has been prepared by Inmarsat in good faith, and all reasonable efforts have been made to ensure its accuracy, Inmarsat makes no warranty or representation as to the accuracy, completeness or fitness for purpose or use of the information. Inmarsat shall not be liable for any loss or damage of any kind, including indirect or consequential loss, arising from use of the information and all warranties and conditions, whether express or implied by statute, common law or otherwise, are hereby excluded to the extent permitted by English law. INMARSAT is a trademark of the International Mobile Satellite Organisation, the Inmarsat LOGO is a trademark of Inmarsat (IP) Company Limited. Both trademarks are licensed to Inmarsat Global Limited. Inmarsat Global Limited 2012. All rights reserved.
Contents 1. Introduction... 3 2. Steelhead Cabling... 3 3. Configure Steelhead... 3 3.1 Login to Steelhead GUI 3 3.2 Configure In-Path Interface 3 3.3 Enable In-Path Optimization 5 3.4 Full Transparency In-Path Rule 6 3.5 Enable HTTP Optimization 7 3.6 Enable Adaptive Compression 8 3.7 Save Configuration 9 3.8 Configure CLI Accessable Settings 9 2 Riverbed Steelhead - Configure Hardware Client inmarsat.com
1. Introduction This document describes the procedure that should be followed to successfully configure the Riverbed Steelhead appliance for Inmarsat s recommended settings. Procedure based on RiOS 7.0.3 interface and commands. 2. Steelhead Cabling Follow the table below to cabling the Steelhead appliance Devices Steelhead to Satellite Terminal Steelhead to PC, Router, or Netgear appliance Cable Crossover Straight-through 3. Configure Steelhead 3.1 Login to Steelhead GUI > 1) Open the Steelhead GUI from your web browser > 2) Login with your username and password. (default is admin and password ) 3.2 Configure In-Path Interface > 1) Navigate to Configure > Networking > In-Path Interfaces 3 Riverbed Steelhead - Configure Hardware Client inmarsat.com
> 2) Click inpath0_0 > 3) Click Specify IPv4 Address Manually > 4) Fill in IPv4 Address, IPv4 Subnet Mask and In-Path Gateway IP fields. Values depend on the configuration of your terminal. For common terminals with default interface settings, use values in the table below. Terminal Address Subnet Gateway Thrane & Thrane Explorer 500 192.168.0.243 255.255.255.0 192.168.0.1 Hughes 9201 192.168.128.243 255.255.255.0 192.168.128.100 Wideye Sabre 1 192.168.1.243 255.255.255.0 192.168.1.35 > 5) Click the Apply button at bottom of page. 4 Riverbed Steelhead - Configure Hardware Client inmarsat.com
3.3 Enable In-Path Optimization > 1) Navigate to Configure > Optimization > General Service Settings > 2) Select Enable In-Path Support and Enable Optimizations on Interface inpath0_0 > 3) Click Apply 5 Riverbed Steelhead - Configure Hardware Client inmarsat.com
3.4 Full Transparency In-Path Rule > 1) Navigate to Configure > Optimization > In-Path Rules > 2) Click Add a New In-Path Rule 6 Riverbed Steelhead - Configure Hardware Client inmarsat.com
> 3) Change WAN Visibility Mode: to Full Transparency with Reset > 4) Click Add 3.5 Enable HTTP Optimization > 1) Navigate to Configure > Optimization > HTTP 7 Riverbed Steelhead - Configure Hardware Client inmarsat.com
> 2) Select Enable HTTP Optimization > 3) Click Apply 3.6 Enable Adaptive Compression > 1) Navigate to Configure > Optimization > Performance 8 Riverbed Steelhead - Configure Hardware Client inmarsat.com
> 2) Select Adaptive Compression > 3) Click Apply 3.7 Save Configuration > 1) Click Save in the top menu bar 3.8 Configure CLI Accessable Settings > 1) Connect to Steelhead CLI via SSH, telnet or serial cable > 2) Login using your username and password (default admin and password ) > 3) Enter the following commands into the CLI enable configure terminal in-path lsp enable in-path peering oobtransparency mode "full" no in-path probe-caching enable protocol http space-in-uri enable in-path probe-ftp-data in-path probe-mapi-data in-path vlan-conn-based in-path mac-match-vlan 9 Riverbed Steelhead - Configure Hardware Client inmarsat.com
tcp sat-opt bw-est mode always tcp sat-opt bw-est mode always write memory restart end end 10 Riverbed Steelhead - Configure Hardware Client inmarsat.com