FCC COMPLIANCE STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC INFORMATION : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. CE COMPLIANCE STATEMENT WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. 2
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 7. Only use attachments/accessories specified by the manufacturer. 8. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 9. CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO. 10. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power sources only. 11. Indoor use only EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 3
1/3 960H Super HAD CCD II 700TVL Super High Resolution Day & Night function WDR (Wide Dynamic Range) High sensitivity 0.1Lux(Color), 0.00005Lux(BW, Sens-up) 3D Noise Reduction Sens-up(~x512) BLC, HSBLC Motion Detection Privacy Masking Defog Multi Language Support (15 languages) 2.8-12mm Auto Iris Vari focal Lens OSD Control (Joystick) 3-Axis (Pan/Tilt/Rotate) Bracket 4
5
6
OSD MENU STRUCTURE SETUP MENU EXPOSURE WHITE BALANCE MOTION DET 3D-DNR PRIVACY MASK SPECIAL SYSTEM EXIT EXPOSURE ALC ELC WHITE BALANCE ATW AUTO AWC-> SET KEY MANUAL DAY NIGHT AUTO SMART IR DAY NIGHT MOTION DET OFF ON 3D-DNR OFF ON PRIVACY MASK OFF ON 7
SPECIAL D.ZOOM D.EFFECT SHARPNESS COLOR DEFOG SYNC USER TITLE LANGUAGE LANGUAGE ENGLISH, CHINESE KOREAN, JAPANESE FRENCH, ITALIAN SPANISH, HEBREW PORTUGUESE, DUTCH, GERMAN, POLISH, RUSSIAN, TURKISH, ARABIC SYSTEM FACTORY RESET EXIT 8
EXPOSURE ALC/ELC BACKLIGHT - Adjusts to view the object clearly in backlight conditions. BLC : The backlight compensation feature helps alleviate issues of visibility in high contrast areas. Set the BLC limit. HSBLC : Use for masking brightness of the specific area to view the subject more clearly. The HSBLC mode is automatically activated only in low luminance scent - AREA setting selects an area. - GRAY SCALE selects a gray scale - USER SCALE selects a bright level (5 levels) - MASK: if setting MASK ON, the mask function is activate only when HSBLC is automatically activated in low luminance scene. WDR : sets Wide Dynamic Range. BRIGHTNESS - Adjust the brightness. If setting the brightness to lower value, the images is darkened. If setting the brightness to higher value, the image gets bright. Lower value(dark image) --- Higher value(bright image) AGC - Set AGC: OFF / LOW / MIDDLE / HIGH If the images are too dark, change the maximum AGC value to make the images brighter. SHUTTER - Select Shutter Speed : AUTO / OFF / A.FLK / 1/160 ~ 1/120,000 SENS-UP - OFF / AUTO(x4) / MANUAL (x2 ~ x10 ~ x512) WHITE BALANCE ATW (Auto Tracing White Balance) Level : -10 ~ 0 ~ 10 AUTO Level : -10 ~ 0 ~ 10 AWC -> SET KEY : It is able to set up the white balance automatically to where the object is seen as desired. MANUAL: Set the white balance options manually. Red: Obtains optimum amount of Red gain. Blue: Obtains optimum amount of Blue gain. 9
DAY / NIGHT AUTO : Set to change the Day / Night mode automatically. NOTE: If you set the AGC to OFF, the AUTO mode of this function is not available and [--] mark is displayed Burst - OFF / ON Allows the color burst signal in monochrome mode to be removed. Level - LOW / MIDDLE / HIGH Dwell Time - 3 ~ 5 ~ 60 sec. Sets the hysteresis time before switching between color/mono & mono/color to reduce the hunting effect SMART IR: Set [ON) to avoid anti-saturation of IR LEDs Burst - OFF / ON Level - -10 ~ 0 ~ 10 Position & size - Adjusts the position & the size of SMART IR. DAY : Color only NIGHT : Monochrome only Burst - allows the color burst signal in monochrome to be removed. OFF / ON NOTE ; Select the BURST-ON or OFF when the color noise occurs on the screen in NIGHT mode. MOTION DETECTION It detects the moving objects in the scent by monitoring changes in brightness level. You can select the level of sensitivity for motion detection to 8 zones. AREA SETUP Sets AREA SELECTION ( 1 ~ 8 AREAS) Sets STAGE - ON / OFF Sets POSITION - Moves horizontal position of the mask Moves Vertical position of the mask Enlarges or decreases the horizontal size of the mark Enlarges or decreases the vertical size of the mark. SENSITIVITY : 0 ~ 50 ~ 100 0 - low sensitivity 100 - high sensitivity DISPLAY - OFF / OUTLINE / MASK 1 / MASK 2 ALARM OUT - OFF / MESSAGE 10
3D-DNR It is used to remove Digital Noise from the image in low light conditions, when AGC is applied. LEVEL : 0 ~ 50 ~ 100 PRIVACY MASK It is used to block out from view part of the field of view from being seen/recorded. Select part the screen to be not displayed. Up to 14 zones can be registered. RECTANGLE - MASK SELECTION : 1 ~ 8 DISPLAY : OFF / ON POSITION : Moves horizontal position of the mask Moves Vertical position of the mask Enlarges or decreases the horizontal size of the mask CIRCLE - MASK SELECTION : 1 ~ 4 DISPLAY : OFF / ON POSITION : Moves horizontal position of the mask. (10~ 90) Moves Vertical position of the mask. (10 ~ 90) SIZE : Enlarges or decreases the horizontal size of the mask. (4 ~ 20) Enlarges or decreases the vertical size of the mask. (4 ~ 20) RADIUS : Enables to adjust the RADIUS size. (1 ~ 100) POLYGON - MASK SELECTION: 1 ~ 2 DISPLAY : OFF / ON SHAPE : draws the polygon on this menu. POSITION : Moves horizontal position of the mask. (10~ 90) Moves Vertical position of the mask. (10 ~ 90) SIZE: Enlarges or decreases the horizontal size of the mask. (4 ~ 20) Enlarges or decreases the vertical size of the mask. (4 ~ 20) NOTE: you can adjust eh mask color manually except for color 8. RED, GREEN, BLUE and TRANSPARENCY adjustments are applied in common from COLOR 1 to COLOR 7, after mask setting 11
SPECIAL D-ZOOM - ZOOM enlarges the screen ( x1.0 ~ x16.0) PAN moves the screen to left of right ( -100 ~ 0 ~ 100) TILT moves the screen to up or down (-100 ~ 0 ~ 100) D-EFFECT- V-FLIP : Flips the picture vertically MIRROR : Turns on the mirror effect ROTATE : Rotates the picture (180 degrees) SHARPNESS - sets the screen sharpness (0 ~ 50 ~ 100) COLOR - switches the displayed picture to gray scale or color. ON: displays the picture with color (0 ~ 50 ~ 100) OFF: displays the picture with gray scale (0 ~ 50 ~ 100) DEFOG - Images in extraordinary environment such as for or rain or in a very strong luminous intensity have DR(Dynamic Range), lower than ordinary images. It has a contrast based defog function, which is used to overcome such shortcoming. ON - LEVEL (0 ~ 10) SYNC - INT This model supports only INT(internal) in SYNC. 12
USUER TITLE - You can use the camera identification to assign a number and character to the camera. It is displayed on the upper left of the screen. To remove the user title, Select OFF. 7 USER TITLE A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z - 0 1 2 3 4 5 6 7 8 9 < > CLR POS END CLR: Clear all entered characters and numbers. POS: Move the USER TITLE position on the screen using the arrow buttons. END: Confirm your selection or exit the setting : Moves cursor to left or right. (BLANK): inserts a space at the cursor position. LANGUAGE - Select the viewer language for the camera setup menu and OSD information display ENGLISH CHINESE KOREAN JAPANESE FRENCH ITALIAN SPANISH PORTUGUESE DUTCH GERMANY POLISH RUSSIAN TURKISH ARABIC HEBREW SYSTEM FACTORY RESET - Returns to the camera to the factory default settings. DEFECT PIXEL - It can compensate the defected pixel (which may occur while using.) Press the key to close the lens cap. 13
SPECIFICATION MODEL NTSC PAL POWER Power Source Power Consumption Image Sensor DC 12V±10% / AC24V±10% 3.5W(300mA) 1/3" 960H Super HAD II Total Pixels 1020(H)x508(V) 1020(H)x596(V) Effective pixels 976(H)x494(V) 976(H)x582(V) Scanning System 2:1 interlace Scanning Frequency 15.734KHz(H) x 59.94Hz(V) 15.625KHz(H) x 50Hz(V) VIDEO FUNCTION Sync. System Electronic Shutter Resolution Min. illumination Video Output S/N Ratio Camera Control Image Enhancement BLC(Backlight Compensation) Day & Night MD (Motion Detection) PM (Privacy Masking) WB (White Balance) AGC (Auto Gain Control) Exposure Brightness Sharpness Internal 1/60~ 1/120,000sec 700TVL Color : 0.1 Lux, B/W : 0.05 Lux B/W : 0.00005(Sens-up x512)@ F1.2 50IRE 1.0 Vp-p (75 ohm, composite) 50dB(AGC off) OSD(Joystick Switch) WDR (Wide Dynamic Range) OFF, BLC, HSBLC, WDR Day&Night (ICR Filter) Motion Detection ( 8 areas ) Adjustable Size & Sensitivity Retangle:8 Areas, Circle: 4 Areas, Polygon: 2 Areas ATW(1700K11.000K) / AUTO /One PUSH / MANUAL OFF / LOW / MIDDLE / HIGH ELC /ALC 0 ~ 100 steps 0 ~ 100 steps Sens-up OFF, AUTO(x4), MANUAL(x2 ~ x512) DNR(Dynamic Noise Reduction) 3D DNR (100 Steps) Digital Image Effect Digital Zoom( ~x16), Defog, Mirror, V-flip, Rotate Camera ID 0 ~ 255 CONNECTOR & ETC Title A ~ Z / 0 ~ 9 English, Chinese, Korean, Japanese, French, Italian, Spanish, OSD Language Portuguese, Dutch, German, Polish, Russian, Turkish, Arabic, Hebrew Power Input 2-Pin Wire / Terminal Block / DC Jack Video Output LENS Operating Temperature Operating Humidity External Dimension Weight BNC connector / Spot Out 2.8~12mm F1.2~360 Vari Focal Lens -10 ~ +50 (14 F ~ 122 F) 0 ~ 96% (non-condensing) 120(Ø) x 88(H) mm 285g 14
EXTERNAL DIMENSION
15 50303762A