Tech Note 453 Configuring Windows SharePoint Services for PEM v1.0 to Work with SuiteVoyager v2.6 All Tech Notes and KBCD documents and software are provided "as is" without warranty of any kind. See the Terms of Use for more information. Topic#: 002160 Created: July 2006 Introduction SuiteVoyager's Table Weaver component provides Production Events Module (PEM) data visualization. However, PEM 1.0 was released before SuiteVoyager version 2.6, which requires the Windows SharePoint Services (WSS). To integrate PEM 1.0 and SuiteVoyager 2.6, it is necessary to manually configure the WSS services. This Tech Note provides step-by-step instructions on how to configure the WSS to allow PEM version 1.0 to work with Suitevoyager version 2.6. Note: This technote assumes the user to have working knowledge of PEM, SuiteVoyager and Windows Operating System. If you have any issue with the WSS, refer to http://support.microsoft.com/winsrv2003 and search for WSS. Application Versions Production Events Module (PEM) 1.0 SuiteVoyager 2.6 Windows Server 2003, SP1. Exclude PEM Services from SharePoint Services Control 1. From the Start Menu, select Settings/Control Panel/Administrative Tools/SharePoint Central Administration. The Central Administration site appears as shown in Figure 1 (below): https://wdnresource.wonderware.com/support/kbcd/html/1/t002160.htm 1/9
FIGURE 1: WINDOWS SHAREPOINT SERVICES CENTRAL ADMINISTRATION SITE 2. In the Virtual Server Configuration area, click Configure virtual server settings. The Virtual Server List pane appears as shown in Figure 2 (below): FIGURE 2: VIRTUAL SERVER LIST PANE 3. Select the Virtual Server that you want to add the excluded paths to. The default virtual server is Default Web Site. The Virtual Server Settings list appears as shown in Figure 3 (below): https://wdnresource.wonderware.com/support/kbcd/html/1/t002160.htm 2/9
FIGURE 3: VIRTUAL SERVER SETTINGS CONFIGURATION 4. Under Virtual Server Management, click Define managed paths (Figure 4 below): https://wdnresource.wonderware.com/support/kbcd/html/1/t002160.htm 3/9
FIGURE 4: DEFINE MANAGED PATHS 5. In the Add a New Path area, type the path that you want to exclude in the Path field. For this configuration, enter ProductionMessagingWS1.0 to exclude the path for PEM Production Messaging Services. 6. Select the Excluded path radio button, and click OK (Figure 5 below): https://wdnresource.wonderware.com/support/kbcd/html/1/t002160.htm 4/9
FIGURE 5: CONFIGURE EXCLUDED PATH: PRODUCTIONMESSAGINGWS1.0 7. Ensure ProductionMessagingWS1.0 appears in the Remove selected paths list (Figure 6 below): https://wdnresource.wonderware.com/support/kbcd/html/1/t002160.htm 5/9
FIGURE 6: EXCLUDED PATHS: PRODUCTIONMESSAGINGWS1.0 8. Repeat steps 5, 6, and 7 for PEMErrorViewer to exclude the path for PEM Error Viewer. The Excluded Paths should now show both productionmessagingws1.0 and pemerrorviewer as shown in the following figure: https://wdnresource.wonderware.com/support/kbcd/html/1/t002160.htm 6/9
FIGURE 7: EXCLUDED PATHS: PRODUCTIONMESSAGINGWS1.0 AND PEMERRORVIEWER 9. Close Internet Explorer. Configuring the web.config File 1. Open an HTML or XML editor. This Tech Note uses Microsoft Front Page to perform the following steps. Note: Use extreme caution when completing the following steps. This file is the xml schema used by the configuration site and is critical to its successful operation. Unnecessary modifications will render the configuration site unusable. 2. Open the web.config file. It is located at \Inetpub\wwwroot. 3. Locate the <system.web>element and modify the following sub-element, as shown in Figures 7 and 8 below: Replace: <trust level="wss_minimal" originurl="" /> with: https://wdnresource.wonderware.com/support/kbcd/html/1/t002160.htm 7/9
<trust level="full" originurl="" /> FIGURE 8: DEFAULT TRUST LEVEL SUB-ELEMENT FIGURE 9: MODIFIED TRUST LEVEL SUB-ELEMENT 4. Save the change and close the editor. PEM Production Data should now appear correctly within SuiteVoyager 2.6. Click the following icon to view this file in.pdf format: https://wdnresource.wonderware.com/support/kbcd/html/1/t002160.htm 8/9
B. Nguyen and R. Liddell Tech Notes are published occasionally by Wonderware Technical Support. Publisher: Invensys Systems, Inc., 26561 Rancho Parkway South, Lake Forest, CA 92630. There is also technical information on our software products at Wonderware Technical Support For technical support questions, send an e-mail to support@wonderware.com. back to top 2013 Invensys Systems, Inc. All rights reserved. No part of the material protected by this copyright may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying, recording, broadcasting, or by anyinformation storage and retrieval system, without permission in writing from Invensys Systems, Inc. Terms of Use. https://wdnresource.wonderware.com/support/kbcd/html/1/t002160.htm 9/9