Axxium - iseries () TOPICS Preparation Installation Startup Optional Features Help/Resources www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 1
Startup Step 1 - Turn Off Equipment Verify the iseries and other equipment to be protected by the UPS is powered off Step 2 - Connect Interface Cable iseries Models FC 0551 w/270 installed with B38 Obtain IPK-0003 (1ea) and IPK-0007 (1ea) from your local Invensys or IBM Representative Connect the UPS to the two Servers using the interface cables show in the Diagram Connecting Interface Cable - 2 Servers to 1 UPS www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 2
Rear of iseries Diagram - Connecting Interface Cable - 2 Servers to 1 UPS Startup UPS (Serial, Relay & REPO) Communications Port J14 or UPS Port on iseries J14 or UPS Port on iseries to UPS Interface Cable Kit (INT-0065), Plug UPS end into UPS. Plug the other end into iseries Connectivity Kits included in UPS Enclosure Rear Panel B38 Obtain IPK-0003 to UPS Interface Kit (1ea) and IPK-0007 Splitter Interface Kit (1ea). Contact your local Invensys or IBM Representative IBM FC IBM PN Best PN Description INT-0065 to UPS Interface Cable SPK-0058 CheckUPS II Power Management and Shutdown Software CD-ROM and connecting cable kit (AIX, Windows 9x, Windows NT, Windows 2000, Novell Netware, and many versions of UNIX, including LINUX www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 3
Startup Step 2 - Connect Interface Cable All other iseries Models Connect the UPS to the Server using the interface cable (Best PN INT-0065) show in the Diagram Connecting Interface Cable - 1 Server to 1 UPS The UPS end of the interface cable connects to the UPS communications port. The other end of the interface cable connects to the port marked J14 or UPS on the rear panel of the Server. The interface cable is located in UPS Carton www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 4
Rear of iseries Startup Diagram - Connecting Interface Cable - 1 Server to 1 UPS UPS (Serial, Relay & REPO) Communications Port J14 or UPS Port on iseries to UPS Interface Cable Kit (INT-0065), Plug UPS end into UPS. Plug the other end into Rear Panel B34, B35, B36, B37 & B38 Connectivity Kits included in UPS Enclosure IBM FC IBM PN Best PN Description INT-0065 to UPS Interface Cable SPK-0058 CheckUPS II Power Management and Shutdown Software CD-ROM and connecting cable kit (AIX, Windows 9x, Windows NT, Windows 2000, Novell Netware, and many versions of UNIX, including LINUX www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 5
Startup Step 3 - Preparing to Connect Power to iseries Equipment from the UPS Use UPS Equipment Jumper Cords B34 & B36 - Put away (store) power cords that came with Server equipment. NOTE: B35, B37 & B38 - You used the Server power cord to connect the UPS to utility power Adequate quantity of equipment jumper cords included with UPS for most applications B34 & B36 = three (3) equipment jumper cords B35 & B37 = four (4) equipment jumper cords B38 = five (5) equipment jumper cords Located in UPS carton www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 6
Startup iseries to UPS Equipment Jumper Cord Table Jumper Cord Description Qty Male Female Use with Equipment Models B34 and B36 Table to NEMA 5-15P Three (3) 5-15P 150, 170,, 270, 7102, 7104, 820, 5075 (Best PN LCA-0183) B35 and B37 Table to Four (4) 150, 170,, 270, 5075, 7102, 7104, 820, (Best PN LCA-0180) 5075 B38 Table to Four (4) 150, 170,, 270, 5075, 7102, 7104, 820, (Best PN LCA-0180 5075 C19 to C20 One (1) C20 C19 5033, 5034, 5035, FC 0550 w/830 (Best PN LCA-0286) 5-15P C19 C20 www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 7
Startup Step 4 - Plug your Equipment Into the UPS Plug the equipment into the appropriate UPS output receptacles using the equipment jumper cords supplied with the UPS Go to eserver to UPS Equipment Jumper Cord Table to determine which equipment jumper cords to use View Integrating Power Connection Diagrams B34 B35 B36 B37 B38 www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 8
Diagram - Understanding UPS Equipment Jumper Cord CONNECTOR LEGEND mates to C20 mates to C19 5-15P mates to 5-15R Startup Output Receptacle (R) on UPS Mates to Equipment Cord Connector Equipment Jumper Cord Connector (5-15P Mates to 5-15R) Connector Type on iseries Equipment 5-15R 5-15P Mated Connectors Color Matched Equipment Jumper Cord Connector ( Mates to ) NEMA 5-15P to IEC 820 840W Equipment (Load) e.g. Model 820 power draw in Watts (W) www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 9
5-15R 5-15R Startup Integrating Power Connections B34 Output Receptacles 5-15R 5-15R 5-15R 5-15R Rear of B34 700W Input 5-15P 5-15P 5-15P 5-15P Three (3) Equipment Jumper Cords Included with B34 - Use to Connect Server and OR 270 400W www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 10
Startup Integrating Power Connections B35 Output Receptacles Rear of B35 700W Input Uses Power Cord Four (4) Equipment Jumper Cords Included with B35 - Use to Connect Server and OR 270 400W www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 11
5-15R 5-15R Startup Integrating Power Connections B36 Output Receptacles 5-15R 5-15R 5-15R 5-15R Rear of B36 1,050W Input 5-15P 5-15P 5-15P 5-15P Three (3) Equipment Jumper Cords Included with B36 - Use to Connect Server, and/or Towers Tower Watts V Range Inlet 5075 300 100-240 7104 350 100-240 OR OR + Towers 270 400W 820 840W www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 12
Startup Integrating Power Connections B37 Output Receptacles Rear of B37 1,050W Input Uses Power Cord Four (4) Equipment Jumper Cords Included with B37 - Use to Connect Server, and/or Towers Tower Watts V Range Inlet 5075 300 100-240 7104 350 100-240 OR OR + Towers 270 400W 820 840W www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 13
Startup Integrating Power Connections B38 Output Receptacles C19 C20 Rear of B38 2, Input Uses Power Cord Five (5) Equipment Jumper Cords Included with B38 - Use to Connect Server, and/or Towers Tower Watts V Range Inlet C19 5075 300 100-240 7104 350 100-240 5074 990 200-240 C20 5033 310 100-240 C20 5034 550 200-240 C20 OR OR 5035 1,029 200-240 C20 + Towers 270 400W 820 840W www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 14
Startup Integrating Power Connections B38 Output Receptacles C19 C20 Rear of B38 2, Input Uses Power Cord Five (5) Equipment Jumper Cords Included with B38 - Use to Connect Server, and/or Towers C19 + FC 0551 w/ 270 750W FC 0551 w/ 270 750W www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 15
Startup Integrating Other Power Connections A few models of Server Equipment have larger plug types e.g. 840 CEC, SB3 CEC & 9309. If you want to power this type of equipment, or, equipment that requires more VA or Watts than the UPS can provide, contact your local Invensys or IBM Representative and request an Axxium Pro 3kVA or 6kVA 9910-UPS www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 16
Startup Step 5 - Turn on your Equipment Turn on equipment sequentially If the UPS alarm beeps when you start the equipment, the UPS may be overloaded. For more information go to Troubleshooting in the Axxium Rackmount User Guide Set QUPSDLYTIM system value for the UPS Monitoring feature UPS monitoring is a standard feature of the iseries operating system. QUPSDLYTIM is a timer in the Server that tells the system how long to run on UPS power before shutting down. Each system is initially assigned a default value for QUPSDLYTIM. A complete description of QUPSDLYTIM is provided on the Information Center Internet site at: http://publib.boulder.ibm.com/pubs/html/as400/ic2924/index.htm. www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 17
COMPLETE! You have completed the Installation and Startup of the UPS www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 18
Help/Resources -IBM iseries www.as400.ibm.com/tstudio - Resource for site preparation and product power information www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 19
Help/Resources - Invensys EMEA TECHNICAL SUPPORT Telephone +44 1753 608 821 Graham.Muncer@PSD.Invensys.com SERVICE SUPPORT E Mail Invensys.Service@digitec-direct.co.uk MISSING ACCESSORIES E Mail Missing.accessories@PSD.Invensys.com www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 20
Help/Resources - Invensys Americas, APAC U.S. & Canada Help Desk (8AM - 8PM EST) M - F +1 800 925 4426, or +1 919 870 3149 techsupt@psd.invensys.com Latin America Web Help Desk (8AM - 8PM EST) M - F +1 919 870 3149 techsupt@psd.invensys.com www.invensys-power.com/ibmups/9910solutions.html www.invensys-power.com/ibm-ups/9910solutions.html, AxxStart-iSeries Dec, 2000 Page 21