Amarillo Instructions for Using Current Production Parts List for Small Pump Drives 1. These parts lists are for current production models from the model to the model 350. Contact Amarillo for prices. 2. To make sure you get the correct parts, always provide the serial number of the gear drive when ordering parts. 3. General drawing for pump drives and combination assemblies are provided for parts identification. A member of The Marmon Group of companies Copyright 03 Amarillo Co.
Model and 30 Parts List Ref. Model Model Part No. 30 No. Description 10 S10C Case 11 S11S Cover 12 ST Horizontal Carrier STS Short Horizonal Carrier, 4:3 & 3:2 Ratios 16 S16T Oil Seal Plate 17 S17FW Bottom Plug With Oil Tube S18 Inspection Plate (Not Shown) 19 S19F Oil Screw X 1331 Bearing Bushing, Light Thrust 21 S21RD Thrust Bearing Cover 22 24 S24R Non Reverse Clutch 241 242 NR Non Reverse Pins, Set of 4 Vertical Shaft, Standard & Light Thrust, Drive Sleeve Vertical Shaft, Standard & Light Thrust, Drive Nut 450 451 Vertical Under Spacer 480 3000-312 Retaining Ring Horizontal Shaft 1:1, 6:5, & Increasing Ratios Horizontal Shaft, 3:2 & 4:3 Ratios 550 551 560 1231 Locknut Set 7407BG Thrust Bearing X 6407 Thrust Bearing, Light Thrust X QJ309 Thrust Bearing, Light Thrust 601 68 Vertical Lower Bearing 602 25821/77 Horizontal Outer Bearing 603 25821/77 700 1168 700 1358 701 702 801 1237 802 12456 803 S 25 E25W 807 808 809 816 825 G 531 910 MK1 911 MK1 912 MK2 9 Horizontal Inner Bearing Drive Nut, Obsolete Drive Sleeve, Current Design Oil Tube (Order with Bottom Plug) Oil Seal Oil Line Manifold Oil Line Manifold with Fittings Oil Line Set of Case Gaskets (below S/N 231989) Loctite Gasket Sealant 50ml tube (S/N 231989 & above) Vertical Shaft Key Horizontal Shaft Key Horizontal Shaft Key SOME PART NUMBERS DETERMINED BY RATIO AND/OR OPTIONAL FEATURES. ALWAYS PROVIDE SERIAL NUMBER OF DRIVE WHEN ORDERING PARTS FOR VERIFICATION.
Ref. No. 10 10 11 12 16 17 19 21 22 24 241 242 450 451 480 550 551 560 601 602 603 700 700 701 702 801 802 803 807 808 809 816 825 910 911 912 9 Model 40 Parts List Description J10F Case, 12" BD J10FX Case, 16-1/2" BD J11A Cover J12B1 Thrust Bearing Carrier JD Horizontal Carrier JDS Short Horizonal Carrier, 4:3, 3:2, 7:4, 2:1 & 3:1 Ratios J16A Oil Seal Plate J17EW Bottom Plug With Oil Tube E18 Inspection Plate (Not Shown) J19E Oil Screw J Thrust Bearing Bushing J21RB Thrust Bearing Cover J24R Non Reverse Clutch NR 40 Non Reverse Pins, Set of 4 Vertical Shaft, Standard & Light Thrust, Drive Sleeve Vertical Shaft, Standard & Light Thrust, Drive Nut Vertical Under Spacer 3000-393 Retaining Ring 2258 Horizontal Shaft 2230 Locknut Set 6312 Thrust Bearing, Light Thrust 7312BG Thrust Bearing, Standard Thrust 6211 Vertical Lower Bearing M8011/48 Horizontal Outer Bearing M8011/48 Horizontal Inner Bearing 2124 Di Drive Nut, Obsolete 2381 Drive Sleeve, Current Design 7075-2 Oil Tube (Order with Bottom Plug) 141 Oil Seal S 25 Oil Line Manifold E25W Oil Line Manifold with Fittings Oil Line 2255 Cooling Coil GC 40 Complete Set of Gaskets (below S/N 231989) 531 Loctite Gasket Sealant 50ml tube (S/N 231989 and above) MK3 Vertical Shaft Key MK3 Horizontal Shaft Key MK10 Horizontal Shaft Key P1030-4 Oil Sight Glass SOME PART NUMBERS DETERMINED BY RATIO AND/OR OPTIONAL FEATURES. ALWAYS PROVIDE SERIAL NUMBER OF DRIVE WHEN ORDERING PARTS FOR VERIFICATION.
Model 60A and 80A Parts List Ref. Model Model Part No. 60A 80A No. Description 10 P10D Case 11 P11B Cover 12 X P12 Thrust Bearing Carrier 12 X P12AR Thrust Bearing Carrier 12 X P12AR Thrust Bearing Carrier, Light Thrust 12 X P12SR Thrust Bearing Carrier, Light Thrust X P13TA Horizontal Carrier X P13TS Short Horizonal Carrier, 8:5, 2:1, & 3:1 Ratios X P14TA Horizontal Carrier X P14TS Short Horizonal Carrier, 5:2, 2:1, & 3:1 Ratios 16 X P16D Oil Seal Plate 16 X P16TFS Oil Seal Plate 17 P17EW Bottom Plug With Oil Tube E18 Inspection Plate (Not Shown) 19 P19E Oil Screw X 21 X P21RDH Thrust Bearing Cover 21 X P21RBH Thrust Bearing Cover 21 X P21RBH Thrust Bearing Cover, Light Thrust 21 X P21RDH Thrust Bearing Cover, Light Thrust 22 E22 Cover Plug 24 P24R-1 Non Reverse Clutch 241 242 NR60 or NR80 Non Reverse Pins, Set of 4 X 3765-1 Vertical Shaft, Standard Thrust Vertical Shaft, Light Thrust 450 451 Vertical Under Spacer 480 3000-433 Retaining Ring X 3391 Horizontal Shaft X 3392 Horizontal Shaft Horizontal Shaft, 8:5, 7:4, 2:1, & 3:1 Ratios 550 551 560 X 2230 Locknut Set 560 X 3268 Locknut Set X 7312 Thrust Bearing X 7412 Thrust Bearing X 6412 Thrust Bearing, Light Thrust X 2-7312 Thrust Bearing, Light Thrust 601 602 X 602 X 603 X 603 X 700 701 702 801 802 X 802 X 803 807 808 809 816 825 910 911 912 9 6212 HM810/40 JHM807012/45 HM810/48 HM807010/46 3841 N-11 7075-3 141 18733 S 25 E25W 3353 GC 60 or GC 80 531 MK10 401100 Vertical Lower Bearing Horizontal Outer Bearing Horizontal Outer Bearing Horizontal Inner Bearing Horizontal Inner Bearing Drive Sleeve Drive Sleeve Key Drive Sleeve Locknut Oil Tube (Order with Bottom Plug) Oil Seal Oil Seal Oil Line Manifold Oil Line Manifold with Fittings Oil Line Cooling Coil Complete Set of Gaskets (below S/N 231989) Loctite Gasket Sealant 50ml tube (S/N 231989 and up) Vertical Shaft Key Horizontal Shaft Key Horizontal Shaft Key CR v seal for S60A thru S125A SOME PART NUMBERS DETERMINED BY RATIO AND/OR OPTIONAL FEATURES. ALWAYS PROVIDE SERIAL NUMBER OF DRIVE WHEN ORDERING PARTS FOR VERIFICATION.
Model 100A and 125A Parts List Ref. Model Model Part No. 100A 125A No. Description 10 P10D Case 11 P11B Cover 12 X P12AR Thrust Bearing Carrier 12 X P12SR Thrust Bearing Carrier 12 P12SR Thrust Bearing Carrier, Light Thrust X P14TA Horizontal Carrier X P14TS Short Horizonal Carrier, 5:2, 2:1, & 3:1 Ratios X PTA Horizontal Carrier 16 P16TFS Oil Seal Plate 17 P17EW Bottom Plug With Oil Tube E18 Inspection Plate (Not Shown) 19 P19E Oil Screw 21 X P21RBH Thrust Bearing Cover 21 X P21RDH Thrust Bearing Cover 21 P21RDH Thrust Bearing Cover, Light Thrust 22 E22 Cover Plug 24 P24R-1 Non Reverse Clutch 241 242 NR 100 Non Reverse Pins, Set of 4 X 3765-1 Vertical Shaft, Standard Thrust X 3765-4 Vertical Shaft, Standard Thrust 3765-4 Vertical Shaft, Light Thrust 450 451 Vertical Under Spacer 480 3000-433 Retaining Ring X 3392 Horizontal Shaft X 3267 Horizontal Shaft X Horizontal Shaft, 5:2, 2:1, & 3:1 Ratios 550 551 560 3268 Locknut Set X 7412BG Thrust Bearing X 2-7312 Thrust Bearing 2-7312 Thrust Bearing, Light Thrust 601 6212 Vertical Lower Bearing 602 X JHM807012/45 Horizontal Outer Bearing 602 X HM807010/46 Horizontal Outer Bearing 603 X HM807010/46 Horizontal Inner Bearing 603 X 5535/5566 Horizontal Inner Bearing 700 3841 Drive Sleeve 701 Drive Sleeve Key 702 N-11 Drive Sleeve Locknut 801 7075-3 Oil Tube (Order with Bottom Plug) 802 18733 Oil Seal 803 S 25 Oil Line Manifold E25W Oil Line Manifold with Fittings 807 Oil Line 808 809 816 3353 Cooling Coil 825 GC 100 or GC 125A Complete Set of Gaskets (below S/N 231989) 531 Loctite Gasket Sealant 50ml tube (S/N 231989 & above) 910 911 912 9 MK10 401100 P1030-4 Vertical Shaft Key Horizontal Shaft Key Horizontal Shaft Key CR v seal for S60A thru S125A Oil Sight Glass SOME PART NUMBERS DETERMINED BY RATIO AND/OR OPTIONAL FEATURES. ALWAYS PROVIDE SERIAL NUMBER OF DRIVE WHEN ORDERING PARTS FOR VERIFICATION.
Ref. No. 10 11 12 16 17 19 21 22 24 241 242 450 451 480 550 551 560 601 602 603 700 701 702 801 802 803 807 808 809 816 825 910 911 912 9 Model 0A Parts List Description P10M Case P11B Cover P12S2M Thrust Bearing Carrier, Standard or Light Thrust PM Horizontal Carrier PMS Short Horizonal Carrier, 7:4, 2:1 & 5:2 Ratios M16B Oil Seal Plate P17MW Bottom Plug With Oil Tube E18 Inspection Plate (Not Shown) P19M Oil Screw P21RMH Thrust Bearing Cover, Standard or Light Thrust E22 Cover Plug P24RM Non Reverse Clutch NR125 Non Reverse Pins, Set of 4 3465-3 Vertical Shaft, Standard or Light Thrust Vertical Under Spacer 3000- Retaining Ring 3464 Horizontal Shaft Horizontal Shaft, 7:4, 2:1, 5:2, & 3:2 Ratios 5237 Locknut Set 2-73BG Thrust Bearing, Standard or Light Thrust 62 Vertical Lower Bearing JH211710/49 Horizontal Outer Bearing JH211710/49 Horizontal Inner Bearing P700M Drive Sleeve Drive Sleeve Key N-14 Drive Sleeve Locknut 7075-7 Oil Tube (Order with Bottom Plug) 24370 Oil Seal S 25 Oil Line Manifold E25W Oil Line Manifold with Fittings Oil Line 3353 Cooling Coil GC 0A Complete Set of Gaskets (S/N below S/N 231989) 531 Loctite Gasket Sealant 50ml tube (S/N 231989 & above) MK6 Vertical Shaft Key MK6 Horizontal Shaft Key MK Horizontal Shaft Key P1030-4 Oil Sight Glass SOME PART NUMBERS DETERMINED BY RATIO AND/OR OPTIONAL FEATURES. ALWAYS PROVIDE SERIAL NUMBER OF DRIVE WHEN ORDERING PARTS FOR VERIFICATION.
Ref. No. 10 11 12 16 17 19 21 22 24 241 242 450 451 480 550 551 560 601 602 603 700 701 702 801 802 803 807 808 809 816 825 910 911 912 9 M10F M11B M12 M13TF M13STF M16B M17BW E18 M19B Model 0A Parts List Description Case Cover Thrust Bearing Carrier, Standard or Light Thrust Horizontal Carrier, Speed Increasing, 1:1 & 11:10 Ratios Horizonal Carrier, Speed Decreasing, Except 11:10 Ratio Oil Seal Plate Bottom Plug With Oil Tube Inspection Plate (Not Shown) Oil Screw M21RDH Thrust Bearing Cover, Standard or Light Thrust E22 Cover Plug M24R-1 Non Reverse Clutch NR 0 Non Reverse Pins, Set of 4 5853 Vertical Shaft, Standard or Light Thrust Vertical Under Spacer 3000-550 Retaining Ring 5262 Horizontal Shaft, Increasing, 1:1, & 11:10 Ratios 5261 Horizontal Shaft, Decreasing 5383 Horizontal Shaft, 8:5 Ratio 5813 Horizontal Shaft, 7:4 Ratio 5345 Horizontal Shaft, 5:2 Ratio 5265 Horizontal Shaft, 2:1 Ratio 5339 Horizontal Shaft, 3:1 Ratio 5237 2-73BG 6216 632/642 Locknut Set Thrust Bearing, Standard or Light Thrust Vertical Lower Bearing Horizontal Outer Bearing H414210/49 Horizontal Inner Bearing 5411 Drive Sleeve MK6 Drive Sleeve Key AN- Drive Sleeve Locknut 7075-4 Oil Tube (Order with Bottom Plug) 24370 Oil Seal S 25 Oil Line Manifold E25W Oil Line Manifold with Fittings Oil Line 5377 Cooling Coil GC 0 Complete set of Gaskets (below S/N 231989) 531 Loctite Gasket Sealant 50ml tube (S/N 231989 & above) MK6 Vertical Shaft Key MK6 Horizontal Shaft Key MK Horizontal Shaft Key P1030-4 Oil Sight Glass SOME PART NUMBERS DETERMINED BY RATIO AND/OR OPTIONAL FEATURES. ALWAYS PROVIDE SERIAL NUMBER OF DRIVE WHEN ORDERING PARTS FOR VERIFICATION.
Model 250, 300, & 350 Parts List STANDARD DRIVE, TYPE S, FIGURE 1 ROTATION Ref. Model Model No. 250 300 & 350 Description 10 M10F Case 11 M11B Cover 12 M12T Thrust Bearing Carrier MT Horizontal Carrier, Speed Increasing, Except 10:11 and 4:5 MTS Horizonal Carrier, Speed Decreasing, 1:1, 10:11, & 4:5 16 L16A Oil Seal Plate 17 M17TW Bottom Plug With Oil Tube E18 Inspection Plate (Not Shown) 19 M19T Oil Screw 21 M21T Thrust Bearing Cover 22 E22 Cover Plug 24 M24R-1 Non Reverse Clutch 241 242 NR 250 Non Reverse Pins, Set of 4 5590 Vertical Shaft, Increasing, 1:1, & 11:10 Ratios 5627 Vertical Shaft, Decreasing Ratios 450 451 Vertical Under Spacer 480 M40T Cup Adjustment Plate 5594 Horizontal Shaft, 1:1, 10:11 & 11:10 Ratios 5598 Horizontal Shaft, 6:5, 4:3, 3:2, & 5:4 Ratios 5612 Horizontal Shaft, 2:1 Ratio 5667 Horizontal Shaft, 3:1 Ratio 5636 Horizontal Shaft, 5:2 Ratio 5741 Horizontal Shaft, 7:4 Ratio 5599 Horizontal Shaft, 4:7, 2:3, & 3:4 Ratios 550 551 560 6217 Locknut Set 561 AN17/W17 Horizontal Retainer HM926710/40 Thrust Bearing 601 JHM516810/49 Vertical Lower Bearing 602 742/749 Horizontal Outer Bearing 603 6535/6580 Horizontal Inner Bearing 700 5585 Drive Sleeve 701 MK14 Drive Sleeve Key 702 AN16 Drive Sleeve Locknut 801 7075-12 Oil Tube (Order with Bottom Plug) 802 29384 Oil Seal 803 S 25 Oil Line Manifold E25W Oil Line Manifold with Fittings 807 Oil Line 808 809 816 X 5377 Cooling Coil 816 X FP5X12-14/AMA Heat Exchanger 825 GC 250 Complete Set of Gaskets (below S/N 231989) 531 Loctite Gasket Sealant 50ml tube (S/N 231989 & above) 910 MK12 Vertical Shaft Key 911 MK Horizontal Shaft Key 912 MK16 Horizontal Shaft Key 9 AN16 Oil Screw Locknut P1030-4 Oil Sight Glass SM 300 Shims SOME PART NUMBERS DETERMINED BY RATIO AND/OR OPTIONAL FEATURES. ALWAYS PROVIDE SERIAL NUMBER OF DRIVE WHEN ORDERING PARTS FOR VERIFICATION.
Amarillo Combination Parts List Ref No. 12 21 702 724 736 756 757 758 769 770 792 60Z Description Thrust Bearing Carrier Thrust Bearing Bushing Thrust Bearing Cover Vertical Shaft Thrust Bearings Drive Sleeve Locknut Sliding Clutch Non-Reverse Pins, Set Drive Sleeve Drive Sleeve Cover Bearing Bushing Retaining Ring, Outer Retaining Ring, Inner Gib Key Steady Bearing & 30 S12S Not Used S1121R 2-7407BG N-07 1183 NR C 1212 1213 1214 3000-281 3100-137 67-2RS 40 60A 80A, 100A, & 125A J12S P12SRC P12S2 JS Not Used Not Used J2321 P21N P21N 2-7312BG 2243 2248 NR C40 2241 2242 2244 3000-334 3100-177 69-2RS 2-7312BG N-11 3293 NR C60 3290 3291 3294 3000-393 3100-2 6211-2RS 2-7412BG N-11 3293 NR C80 3290 3291 3294 3000-393 3100-2 6211-2RS Ref No. 12 21 702 724 736 756 757 758 769 770 792 60Z Description Thrust Bearing Carrier Thrust Bearing Bushing Thrust Bearing Cover Vertical Shaft Thrust Bearings Drive Sleeve Locknut Sliding Clutch Non-Reverse Pins, Set Drive Sleeve Drive Sleeve Cover Bearing Bushing Retaining Ring, Outer Retaining Ring, Inner Gib Key Steady Bearing 0A P12C Not Used P21NC 2-73BG N-14 3468 NR C0A 3689 3690 3469 3000-433 3100-237 6212-2RS 0A M12SB Not Used M21C 2-74BG AN- 5274 NR C0 5271 5272 5273 3000-475 3100-275 6214-2RS 250, 300, & 350 5643 M21TC AN-16 5647 NR C250 5644 5645 5646 3000-5100-293 62-2RS SOME PART NUMBERS DETERMINED BY RATIO AND/OR OPTIONAL FEATURES. ALWAYS PROVIDE SERIAL NUMBER OF DRIVE WHEN ORDERING PARTS FOR VERIFICATION.