VISTA 20HW INSTALLATION INSTRUCTIONS 2-PARTITIONED SECURITY SYSTEM. Principal changes in this issue are indicated by margin lines, N7526-2V14/96

VISTA 20HW 2-PARTITIONED SECURITY SYSTEM INSTALLATION INSTRUCTIONS Principal changes in this issue are indicated by margin lines, N7526-2V14/96

HOW TO USE THIS MANUAL...6 CONVENTIONS USED IN THIS MANUAL...7 RECOMMENDATIONS FOR PROPER PROTECTION...8 Section 1. Section 2. Section 3. Section 4. Section 5. Section 6. GENERAL DESCRIPTION...9 INSTALLING THE CONTROL... 12 Mounting the Cabinet... 12 Installing the Lock (if used)... 12 Mounting the Control s Circuit Board in the Cabinet... 13 Standard Phone Line Connections... 14 Wiring the AC Transformer... 14 Installing the Back-Up Battery... 15 Earth Ground Connections... 15 INSTALLING REMOTE KEYPADS....... 16 Keypads That May Be Used... 16 Wiring The Keypads... 16 Wiring Run Chart... 16 Mounting The Keypads... 17 Using A Supplementary Power Supply To Power Additional Keypads... 17 Preliminary Check-Out Procedure... 18 MECHANICS OF PROG~~G... 19 General Programming Information... 19 Entering Program Mode... 19 Programming a Data Field... 19 Reviewing a Data Field/Erasing an Entry in a Data Field... 20 Interactive Mode Programming (*56, *80, *81, and *82)... 20 Loa&ng Facto~Defaults...2O Programming System Setup Fields...... 20 Exiting the Programming Mode... 20 BASIC HARD-WIRED ZONES 1-8... 21 Installing the Hard-Wired Zones...21 Common Characteristics For Zones 1 8... 21 Wiring Burglary and Panic Devices to Zones 1 8...2l Wiring 2-Wire Smoke Detectors to Zone 1... 21 Veri@ Operation of 2-Wire Smoke Detectors in Zone 1... 21 Turning Off Fire Alarm Sounding... 21 Wiring 4-Wire Smoke/Combustion Detectors on Zones 2 7... 22 Wiring 2-Wire Latching Type Glass Break Detectors on Zone 8...23 Programming Hard-Wired Zones... 24 Check-Out Procedure for Hard-Wired Zones... 26 WIRED ZONE EXPANSION (4219, 4229)...27 Installing Zone Expansion Units... 27 Connections and Set-Up.....27 Programming Wired Expansion Zones... 28 Check-Out Procedure for Wired Expansion Zones... 30-2-

Section 7. Section 8. Section 9. Section 10. Section 11. Section 12. Section 13. Section 14. RELAY OUTPUTS & POWERLINE CARRIER DEVICES...31 Relay/Powerline Carrier Device Basics...3I Nos. 4204 And 4229 Output Relay Modules...31 4204/4229 Setup... 31 Powerline Carrier Devices...32 Wiring Comedians... 33 Programming Options Defined... 34 Programming Output Relays and Powerline Carrier Detices...36 42S5 VIP (VISTA Interactive Phone) MOD~... 39 Installing the 4285 Module... 39 General Information...39 Mounting The 4285 Modtie... 39 4285 Module Wifing...40 Caller ID Units...4O Programming The Control For Phone Access... 42 Checking the Operation of the 4285 Module...43 memmsowem...44 Compatible Sounders...44 Sounder Connections... 44 Programming For External Sounders... 45 Testing the Somder...46 LONG RANGE ~10...47 General Itiormation...47 Connection...47 Progmming...47 REMOTE KEYSWITCH... 48 Installing the Keystitch...48 Remote Keyswitch Comections... 48 Programming for the Remote KeysWitch... 50 KeysWitch Operation...51 AUDIO ALARM VERIFICATION (AAV) UNIT...52 General Ifiomation... 52 Wiring Comections... 52 Programming... 52 FINAL POWER W... 54 Earth Ground Connections...54 Connecting the Back-Up BatteW...54 Calculating the Battery Size Needed... 54 Making the Battery Connections...55 Auxiliary Device Current Draw Worksheet... 55 ALPHA DESCRIPTION PROG~G...56 Assigning Zone Descriptors...56 Entering Zone Descriptors (in program Menu Mode *82)...56 Programming the Descriptors...56 Alternate Method for Programming Zone Descriptors... 58 Adding Custom Words...59 Alpha Vocabulary List (For Entering Zone Descriptors)... 60 Character (ASCII) Chd...6O -3-

Section 15. Section 16. SYSTEM COMMUNICATION...6l Report Code Formats...6l Table of Contact ID Codes...63 Communication Programming...64 ZONE RESPONSE TYPE DEFINITIONS...69 Section 17. DATA FIELD D=C~IONS...7l Description of System Data Fields... 71 Section 18. REMOTE PROGRAMMING AND CONTROL (DOWNLOADING)... 81 General Itiormation... 81 Equipment Required...81 Inititial Download...8l Remote Programming Information...8l Remote Programming Advisory Notes...82 Section 19. TESTING THE SYSTEM... 83 Test Procedure...83 To the Installer...83 Section 20. SYSTEM OPERATION...84 Security Codes... 84 Installer Code... 84 Master Code...84 Secondary User Codes... 84 Keypad Functions... 85 General Information...85 Arming Functions...85 Summary of bing Modes... 85 Panic Keys...85 Relay/Powerline Carrier Devices (if used)... 86 4285 Module...86 Exit Alarm Displays... 86 Trouble Conditions...87 General Information...87 Check and Battery Displays...87 Telephone Line Failure...87 Power Failure... 87 Other Displays (Fixed Word Kenads)...87 Section 21. TROUBLESHOOTING GUIDE...88 Contacting Technical Support In The Event Of Problems...89 REGULATORY AGENCY STATEMENTS... 99 Section 22. SPECIFICATIONS & ACCESSORIES...91 Specifications...91 Accessories (Compatible Detices)...93 LIMITATIONS OF THIS ALARM SYSTEM...94 INDEX... 95 VISTA-20HW s UMMARY OF CONNECTIONS DIAGRAM...-...InSideBackcover JJMrrm wmmw...backcover PROGRAMMING FORM...Insert 4-

LIST OF FIGURES Figure 1. Installing the Cabinet Lock... 12 Figure 2. Mounting the PC Board in the Cabinet... 13 Figure 3. Telephone Line Connections... 14 Figure 4. Connection of 4300 Transformer to the Control Board... 15 Figure 5. Keypad Connections to the Control Board... 17 Figure 6. Using a Supplementary Power Supply... 18 Figure 7. 2-Wire Smoke Detector Connected to Zone 1... 22 Figure 8. 4-Wire Smoke Detector Connections (Zones 2 7)... 22 Figure 9. Glass Breiik Detector Connections to Zone 8... 23 Figure 10. Wiring Comection, 4219& 4229 (4229 shown)... 27 Figure 11. 4229 Connections To Control... 32 Figure 12. 4204 Connections To Control... 32 Figure 13. 4300 Transformer Wiring Connections...33 Figure 14. 4285 VIP Module Wiring Connections... 41 Figure 15. Typical Sounder Wiring... 45 Figure 16. Long Range Radio Cometiions... 47 Figure 17. (A) KeysWitch Wiring (4300 Interface transformer Not Used)...49 (B) KeysWitch Wiring (4300 Interface transformer Also Used)... 49 Figure 18. Connection of AAV Unit When Not Using a 4285 VIPModule...53 Figure 19. Connection of AAV Unit When Also Using a 4285 VIP Module...53 Figure 20. VISTA-20HW Summary of Connections...Inside Back Cover -5-

HOW TO USE THIS MANUAL This manual is written to accommodate both the new and the experienced installer of Ademco products. A general description of the entire system is located at the beginning of the manual. The wiring and physical setup of the hardware follows. The sections at the core of the manual include both hardware setup and programming requirements of each device to make that specific device operational in the system. A checkout procedure is included at the end of each section. We recommend this method to ensure that each device is working properly before proceeding to the next section. It must also be used if you are making a particular addition to the system of one of these devices. Each of the sections covering the installation of peripheral devices includes the programming for that device. Without an understanding of the programming of the system, you will not be able to successfully perform the required programming in each of these sections. We therefore urge you to read Section 2. Mechanics of Programming before any programming is performed. If you are an experienced user of Ademco products, you may choose to wire and then program the entire system at once. If so, refer to Section 4: Mechanics of Programming and Section 19. Data Field Descriptions after the hardware setup is complete. A blank pull-out programming form is included with this manual. This manual uses various icons to denote critical notes and technical tips to assist you with the installation of this system. These are easily seen in the left-hand column of the relevant information. w. -6-

CONVENTIONS USED IN THIS MANUAL Before you begin using this manual, it is important that you understand the meaning of the following symbols (icons). II Many system options are programmed in an interactive mode by responding to Alpha keypad dmplay prompts. These prompts are shown in a double-hnebox. *OO When programming the system, data fields are indicated by a star (*) followed by the data field number. PRODUCT MODEL NUMBERS: Unless noted otherwise, references to specific model numbers represent Ademco products. -7-

RECOMMENDATIONS FOR PROPER PROTECTION The Following Recommen dations For The Location Of Fme And Burglary Detection Devicee Help Frovfde Proper Coverage For The Protected Premieee. Recommendations For Smoke And Heat Detectors w With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association s (NFPA) Standard #72 noted below. Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows: For minimum protection a smoke detector should be installed outside of each separate sleeping area, and on each additional floor of a multi-floor family living unit, including basements. The installation of smoke detectors in kitchens, attics (finished or unfinished), or in garages is not normally recommended. For additional protection the NFPA recommends that you install h- or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages. In addition, we recommend the following Install a smoke detector inside every bedroom where a smoker sleeps. Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outside may not wake up the sleeper if the door is closed. Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air conditioners or humidifiers) are used. Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long. Install smoke detectors in any room where an alarm control is located, or in any room where alarm control connections to an AC source or Dhone lines are made. If detectors are not so located, a fire within the room could prevent th;control from reporting a fire or an intrusion. II?EOROWI Iol 1 u SmckeC@ectora forminimumpmta.xion ~ SmokeDetectors foraddtionalpmtwtion A Heat-Activeted thocto~ LW4GRM SASEMENT Recommendations For Proper Intrusion Protection For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial premises. This would include any skylights that may be present, and the upper windows in a multi-level building. In addition, we recommend that radio backup be used in a security system so that alarm signals can still be sent to the alarm monitoring station in the event that the telephone lines are out of order (alarm signals are normally sent over the phone lines, if connected to an alarm monitoring station). w -8-

The VISTA-20HW is a 2-partition control that supports up to 16 zones using basic hard-wired and wired expansion zones, plus 3 keypad zones. Baeic Hardwired Zones (8) Provides 8 basic hardwired zones having the following characteristics: EOLR supervision supporting N.O. or N.C. sensors Programmable response time (10, 350, or 700 milliseconds) Individually assignable to either partition Up to sixteen 2-wire smoke detectors on zone 1 4-wire smoke or heat detectors on zones 2 through 7 (as many as can be powered fkom AUX power on the control) Up to fi~ 2-wire latching type glassbreak detectors on zone 8 with auto reset optional Wwed Expansion zones (up to 8) Supports up to 8 additional wired zones using a 4219 expansion module or 4229 expansionhelay module. These zones have the following characteristics: Two partitions EOLR supervision supporting N.O. or N.C. sensors 300-500 msec normal response with an option for fast (10-15 msec) response on loop A (fist expansion zone) Provides the ability to control two separate areas independently, each area functioning as if it had its own separate control (each with its own Master code and user codes, as programmed) Zones assignable to either partition 1 or 2 Relay and Powerline Carrier device outputs assignable to either partition 1 or 2, or to both partitions Certain m o!narnmed svstem odtions. such as Entrv/Exit delav and Subscriber Account n~mber, ~rogrammed indepe~dently for- each partition Remote Keypads Up to 4 of any of the following keypads may be used in each partition: Fixed-Word Keypads: 4127*, 4137AD, 6127*, 6137, and 6128. * These keypads cannot be used if the 4285 VIP (VISTA Interactive Phone) Moduleis beingused. AZphaKeypads: 5137AD, 6139 (2-line alphanumeric displays) 6138 (l-line alphanumeric display). Security Codes One installer code for entire system (user 1) One Master code for each partition (user 2) 12 secondary user codes for each partition (users 3-14) One baby-sitter code for each partition (user 15) c One duress code for each partition (user 16) -9-

Keypad Panic Keys Up to 3 programmable panic key fimctions are provided. Designated as Zones 95, 96, 99. Reported separately by partition, distinguished by subscriber ID number Zone Morntor Feature s The control will sense a high resistance in the loops on hard-wired zones 2-8 if it is present, and will display a trouble message for the affected zone when the system is in the disarmed mode. This feature also prevents the system from being armed while this high resistance condition exists. v Exit Error False Alarm Prevention Feature Enables the system to determine the difference between a regular alarm and an alarm caused by leaving an Entry/Exit or Interior zone open after the exit delay expires. If not disarmed in time, an alarm will sound end an Exit Error report sent to the central station. An Exit Alarm condition will also occur if an Entry/Exit or Interior zone re-opens within 2 minutes after the end of an exit delay. Optional Output Relays and Powerline Carrier Devices (X-1O type) Up to 4 relays using one 4204 Relay Module Up to 2 relays using one 4229 Zone/Relay Module Up to 8 Powerline Carrier devices (you must subtract the number of relay outputs actually used by the 4204 or 4229 modules, if used) Actions programmable to respond to zone activity or manual keypad entries Optional Keyswitch Supports the Ademco 4146 keyswitch on basic hardwire zone 7. May be assigned to either partition. Optional 4285 W (VISTA Interactive Phone) Module Supports the Ademco 4285 VIP (VISTA Interactive Phone) Module on Partition 1 only. Provides access to the system via on premises or off-premises phones for arming, disarming, etc., plus control of relay outputs and Powerline Carrier devices. Audio Akuzn fhrification (AAv optiosl Provides a programmable Audio Alarm Verijleation (AAV) option which can be used in conjunction with an output relay to permit voice dialog Optional Long Range Radio s Allows all messages that have been programmed to go to the primary telephone number to be reported additionally to a 7720 PLUS or 7820 radio. Ckeck availability of these models. -10-

Event Logging The telephone lin;vofiage can be monitored to supervise the phone line connection. The panel must be connected to a proper earth ground or you will get a false line cut indication if this feature is enabled. The loss of the line can optionally cause a local display, or a display and trouble sound. Event Logging feature keeps a record of selected events in a history log (UP to 48 events). All control and readout from the log is done via Ademco V-LIN@ downloading software only. Alarm output Provides a 12VDC, 2 AMP output that can drive the compatible sounders listed in the EXTERNAL SOUNDERS section (assumesa fully chargedbatteryis connected). Steady output for Burglary/Panic, or temporal pulse output (3 pulses pause 3 pulses pause -3 pulses...) for Fire Uses current limiting circuitry for protection Auxiliary pow- progralmnin~ Output Provides 12VDC, 600 ma maximum. Uses current limiting circuitry for protection. This output interrupts for smoke detector reset if 4-wire smoke detectors are used. Prograrqmed options are stored in electrically erasable, non-volatile EEROM memory (information can be reprogrammed at any time and will not be lost in the event of a power loss). The system can be uploaded, downloaded, or controlled via an IBM compatible computer, Ademco V-LINI@ downloading software and a HAYES modem specified by Ademco. Keypad programming consists of: Data field programming Interactive (menu) mode programming communication Formats supfborted Ademco Low Speed (Standard or Expanded) Sescoa/Radionics (Standard or Expanded) Ademco Express Ademco Contact ID Zone Deecriptore You can assign Alpha descriptors to all zones (usefil only when using Alpha keypads and/or the 4285 VIP (VISTA Interactive Phone) module. AC power Supply Uses 1321/TF2, 11OVAC plug-in transformer with 16.5VAC 25VA output,, unless Powerline Carrier devices (ex. X-10 type) are used, in which case a 4300 Imansformer module must be used. Back-up Battery Rechargeable (Gel type) 12VDC, 4AH minimum (Ademco No. 467). -11-

Mounting the Cabinet This section provides instructions for mounting the control cabinet, and installing the cabinet lock (if used). Also included in this section are w instructions for the following Installing the main PC board. Standard phone line connections. Installing the back-up battery in the cabinet. c Connecting the AC transformer. s Making earth ground connections. Mount the control cabinet to a sturdy wall using fasteners or anchors (not supplied), in a clean, dry area which is not readily accessible to the general public. Four mounting holes are provided at the back of the cabinet. Installing the Lock (if used) Use an Ademco No. N6277 Cam (Retainer Clip). Note: The cabinet can be closed screws in the cover s edge. Lock and No. N6277 1 Push-On Clip and secured witbout a lock by using 2 LUXEU 3 RErumn (@. :..... + ao CLw CAmm Doon 90?70!4 1. 2. 3. Remove the cabinet door. It is easily removable for servicing and is easily re-installdd. Remove the lock knockout from the control cabinet door. Insert the key into the lock. Position the lock in the hole making certain that the latch will make contact with the latch bracket when the door is closed. Hold the lock steady, and insert the retainer clip into the retainer slots. Position the clip as illustrated in order to permit easy removal. w Figure 1. Installing The Cabkwt Lock -12-

Mounting The Control s Ckuit Board In The Cabiiet (F@ 2) 1. Hang two short Black mounting clips (provided) on the raised cabinet tabs (see Detail Bin Fig. 2). 2. Insert the top of the circuit board into the slots at the top of the cabinet. Make sure that the board rests on the correct row (see Detail A ). 3. Swing the base of the board into the mounting clips and secure the board to the cabinet with the accompanying screws (see Detail B in Fig. 2). Figure 2. Mounting The PC Board In The Cabiiet -13-

Standard Phone Line Connections TERMINALS ON CONTROL e Incoming phone line and handset wiring is connected to the main terminal block (via a RJ31X jack) as follows (also see Figure 3): Term. 21: Local Handset (TIP - Brown*) Term. 22: Local Handset (RING - Gray*) Term. 23: Incoming Phone Line (TIP Green*) Term. 24: Incoming Phone Line (RING Red*) * Colorsof wiresin DirectConnectCord. Incoming ~ Handset TelcoLine ~ 21 22 W L +& K:::ELcoLINE 23 24 25 IMPORTANT! IF THE PANEL IS NOT CONNECTEDTO A PROPER EARTH GROUND, YOU MAY GET FALSETELEPHONE LINE CUT INDICATIONS (IF THE TELEPHONE UNE MONITOR HAS BEEN PROGRAMMED IN FIELD 92). F&ure 3. Telephone be Connections Wwing The AC Transformer 1321/TF2 4300 If you are going to use a 4300 transformer interface (required if Powerline Carrier devices are going to be used), comect the 4300 transformer s terminals as follows: a. Terminals 1,3 (AC), and 2 (Ground) to control board terminals 1,2, and 25, respectively (see Figure 5). See wiring table below for wire gauge to use. WIRING TABLE Distance of Transformer Wire Gauge Fkom the Control Panel To Use Up ta 50 feet #20 50-100 feet # 18 1 100-250feet I # 16 I Wire the 132UTF2 transformer to terminals 1 and 2 on the control board. See wiring table below for wire gauge to use. Caution must be taken when wiring the transformer to the control panel to guard against blowing the fuse inside the transformer (the fuse is nonreplaceable). -14-

b. Wire the other three terminals (Sync, Data, Corn) on the 43oO transformer. Wires from these terminals must be connected to a 9-pin connector on the control board (using a 4142TR cable supplied with the 4300 transformer), as shown in Figure 4. These particular wires can be 24 gauge or larger, and can be run along with the AC and ground wires to the control panel. The complete wiring for the 4300 transformer is also covered in Section 7. RELAY OUTPUTS & POWERLINE CARRIER DEVICES. Do o Earth TERMINALS ON CONTROL Ill I BOARD ~ UNLESS4146 Kl%tiCH AND/OR ARMINGSTATUSINDICATORIS ALSO USED.SEEFIG.19. NOTEALLUNUSEDWIRESSHOULD BECUTAND/ORTAPED. Figure 4. Connections of 4300 Transformer To The Control Board 1. Place the 12-volt back-up battery in the control cabinet. 2. Attach Red and Black wires on the battery connector cable as follows: a. Red to the positive (+) battery terminal on the control board (see Summary of Connections Diagram for location, if necessary). b. Black to the negative (-) battery terminal on the control board. Earth Ground Connection The designated earth ground terminal (25), must be terminated in a good earth ground for the lightning transient protective devices in this product to be effective. The following are examples of good earth grounds available at most installations: Metal Cold Water Pipe: Use a non-corrosive metal strap (copper is recommended) firmly secured to the pipe to which the ground lead is electrically connected and secured. AC Power Outlet Ground. Available from 3-prong, 120VAC, power outlets only. To test the integrity of the ground terminal, use a three-wire circuit tester with neon lamp indicators, such as the UL-Listed Ideal Model 61 035, or equivalent, available at most electrical supply stores. -15-

This section lists the wired keypads that may be used and provides instructions for wiring and mounting the keypads. A preliminary check-out procedure is also provided to ensure that the - connected keypads are fi.mctioningproperly in the system. Keypads That May Be Used Q Fixed-Word Display: 4137AD, 4127,6127,6128,6137 Alpha Display 5137AD, 6138,6139 Up to 4 keypads in each partition (total of 8 in the system), independent of auxiliary power considerations (you may need to use an auxiliary power supply if the 600mA auxiliary output is exceeded) WIMg To The Keypads 1. Determine wire gauge by referring to the wiring length/gauge chart below. Wire lengths/gauge for Partition 2 keypads should be determined separately from those keypads connected to Partition 1. I 2. Run field wiring from the control to the keypads (using standard 4- conductor twisted wire cable using the wire gauge determined in step 1). Wiring Run Chart For Devices* Drawing Aux Power From l he Control (12V+ & 12V-) I TOTAL CURRENT DRAWN BY ALL DRVICES CONNECTED TO A S~GLE WIRE RUN Wire Size 50 ma or less I 100 InA I 300 ma I 500 IIA I 600 rna #22 500 ft (152m) 250ft (76m) 80 R (24m) 50 f%(15m) 42 ft (13m) #20 750 ft (228.6m) 380ft (l16m) 130it (39.6m) 80 f%(24m) 67 ft (20.4m) #18 1300R (396m) 650ft (198m) 220 ft (67m) 130ft (39.6m) 115ft (35m) #16 1500ft (457m) 1000ft (305m) 330ft (100.5m) 200 f%(70m) 170ft (52m) * IncludesKeypads,Zone Expander/RelayUnits,or 4285Module. -16-

3. Connect remote Keypads for Partition 1 to terminals 4, 5,6, and 7 on the control board, as shown in Figure 5. 4. Connect remote Keypads for Partition 2 to the 4-pin connector on the control board (see the Summary of Connections diagram for location of the 4-pin connector for partition 2). KEYPADCONNECTOR CABLE(SUPPLIED WITH VISTA-20HW) o 5 GREEN 06 YELLOW 0 7 CONTROL TERMINALS PARTITION1 KEYPADS PARTITION 2 KEYPADS CONNECTOR PINS FOR PARTITION2 ON CONTROL BOARD Figure 5. Keypad Connections To The Control Board Mounting the Keypade 1. Make sure addressable type keypads (4137AD, 5137AD, 6128, 6137, 6138, and 6139) are set to non-addressable mode (address 31), which is the factory default setting. Refer to the instructions provided with the keypad for address setting procedure. 2. Mount the keypads at a height that is convenient for the user. Refer to the instructions provided with the keypad for mounting procedure. You can either surface mount or flush mount keypads (using an appropriate Trim Ring Kit: 5137TRK or 6139 TRK). Refer to the mounting instructions and template included with the keypad and/or trim ring kit for specific information. Using a Supplementary Power Supply to Power Additional Keypade The control provides 600mA for powering keypads (up to a maximum of 4 per partition) and other devices from the auxiliary power output. The backup battery will supply power to these keypads in the event that AC power is lost. When the control s auxiliary power load for all devices exceeds 600 ma, you can power additional keypads from a regulated, 12VDC power supply (e.g., 487 12 supplies 12V, 250A, 488 12 supplies 12V, 500mA). Use a UL Listed, battery-backed supply for UL installations. The 487 12/488-12 power supplies have a backup battery which can power these keypads in the event of AC power loss. colors shown. Be sure to observe the current ratings for the power supply used. -17-

.. Pdmmmrp Figure Check-out Procedure 6. Using A Supplementary Power Supply For Keypads If you want to check that the system is working before connecting field wiring fi-om zones and devices, do the following: 1. Temporarily connect a 2000 ohm end-of-line resistor across each of the basic hard-wire zones 1 8, as shown in the Summary of Comections diagram. 2. 3. 4. Without actual zone wiring or EOL resistors connected, the keypads in each partition of the system will not display the Readfl message. Power up the system temporarily by plugging the AC transformer ~ (previously wired to the control) into a 120VAC outlet. Busy - Standby (Alpha keypads) or dl (Fixed-word keypads) will be displayed. After approximately 1 minute*, the green READY LED (or POWER LED on some types of keypads) should light, and the word READY (Fixedword keypads), or DISARM ED... READY TO ARM (Alpha keypads) should be displayed. * To bypass the l-minute delay, press # plus O. If the Ready display does not appear on any of the keypads in the system (in either of the partitions), or a Not Ready message is displayed, check the keypad wiring connections, and make sure each of the 8 basic hardwired zones has a 2000 ohm resistor connected across its terminals. When you get the proper Ready displays on the keypad(s), the system is functioning properly at this point. Do not remove the EOL resistors until you are ready to make connections to the hard-wired zones, to allow for testing later in the manual. -18-

This section provides information on how programming is performed in this system. It will enable you to understand how to enter and exit the programming mode, and how to program the data fields and the user-friendly interactive modes (*56, *80, *81, *82, *83). We therefore urge you to read and understand the following before proceeding with the installation. General. Programming Information Characteristics for each installation are stored in non-removable, electrically erasable, non-volatile EEROM memory. These must be programmed for the particular installation to establish its specific alarm and reporting features. It is possible to program the system at any time, even at the installer s premises prior to the actual installation. Simply apply power temporarily to the control and then program the unit as desired. Important Note: You cannot enter the programming mode unless - partitions are disarmed. There are two programming modes: data field programming and interactive (menu) mode programming. Data field programming is used for setting various system options and interactive programming is used for programming zone information, programming relay outputs, and for learning transmitter serial numbers. I ::,:, Programming can also be performed remotely from the installer s officelhome, using an IBM personal computer, a modem, and V-Link downloading software. See the Section 18. REMOTE PROGRAMMING AND CONTROL (DOWNLOADING). Entering Program Mode You may use one of the following methods: a) Press both the [*I and [#] keys at the same time within 50 seconds after power is applied to the Control, or b) Mter power up, enter the Installer code (4 1 1 2)+8 O 0. This method is disabled if you exit the program mode using *98 instead of *99. See Exiting Program Mode par~aph later in this section. If a diherent Installer code is subsequently programmed, use it instead of 4112 to gain access to the Programming mode. Following entry into program mode, data field *2O will be displayed (this is the first field in the system). The system will now accept entries for field =0. Data F5ekl 1. Press[*I plus Field No. (for example, *21), then make the required entry. 2. When you have completely programmed a data field, the keypad will beep three times and then automatically display the next data field in sequence. Togo to a different field, press [*] plus the desired field No. -19-

Typicalpromptdisplayed during interactivemode programming Enter Zn Num. 1 (00 = Quit) 01 3. If the number of digits that you need to enter in a data field is less than the maximum digits available (for example, the phone number field), enter the desired data, then press * and the next data field number to be programmed. 4. If you try to enter a non-existent field, the keypad will display EE or Q Entry Error. Simply re-enter [*] plus a valid field number. Reviewing a Data Field/Erasing an Entry in a Data Field Press [#] plus Field No. Data will be displayed for that field number. No changes will be accepted in this mode. To delete an entry in a field, press [*] plus Field No. + [*I. (Applies only to fields *40 *46, and *94). Interactive Mode Programming (*56, *SO, *S1, and *82) Press [*] plus interactive mode No. (for example, *56). The Alpha keypad will display the first of a series of prompts requesting entries. A detailed procedure (with displays of prompts) is provided in those sections where programming in the interactive mode is to be performed. 1 Interactive Mode Used To Program Zone Number~ *56 Zone Programming Zone characteristics, report codes, alpha descriptors and serial numbers *8O Relay Programming 4229 or 4204 Relay modules, or Powerline Carrier devices *81 Zone List Programming Zone Lists for relaylpowerline carrier activation *82 Alpha Programming Zone alpha descriptors Loading Factory Defaults To load the factory defaults, enter the programming mode, press *97, then exit the programming mode. *96 resets the Subscriber Account number and CSID in preparation for an initial download. PrOgramnu ng System Setup ~~elds The following program fields must be programmed before doing any zone programming. *2S -D ZONE EXPANSION u Use this field to select the type of expansion unit being used, as follows: O= none; 1 = 4219; 2 = 4229; 3 = 4204. Default is O. *3o KEYSWITCH ENABLE u This field must be enabled (enter 1) if using a keyswitch. The keyswitch must be connected to zone 7, which can then not be used for any other purpose. Default is O (no keyswitch). Note: If keyswitch is enabled, in menu mode *56 the Zone Type (ZT) for zone 7 will show 77, and will not be accessible for programming. Exiting the Programming Mode *99 allowsre-entry~to the progr~ mode using Installer Code + 8 0 0. W8 mbits re-entryintothe programming mode using the Installer code. -20-

This section provides general information for the hard-wired zones in the system, plus specific instructions for installing 2-wire smoke detectors, 4-wire smokekombustion detectors, and 2-wire latching type glass break detectors. Also included is a procedure for programming the hard-wired zones. Installing the Hard-Wwed Zones Common Characteristics for Zones 1-S Can be assigned to any partition EOLR supervised zones supporting both open circuit and closed circuit devices As many 4-wire smoke detectors as can be powered from Aux Power on the control (zones 2-7) Programmable for 10, 350, or 700 msec response 350 msec (default) should be used for most standard contacts. For vibration type contacts, 10 msec is more suitable Whing Burglary and Panic Devices To Zones 1-S 1. Comect sensors/contacts to the hard-wired zone terminals (terminals 8 through 20). See the Summary of Connections chagrdm. 2. Connect closed circuit devices in series in the high (+) side the loop. The EOL resistor must be connected in series with the devices, following the last device. See the Summary of Comections diagram. 3. Connect open circuit devices in parallel across the loop. The 2,000 ohm EOLR must be connected across the loop wires at the last device. High Resistan ce Supervision on Hard-WA Zones 2-S Special supervision in the control senses high resistance on hard-wired zone loops 2-8, causing a warning CHECK display with the tiected zone number to occur when the system is in the disarmed state. The system cannot be armed when this display is present. If the system is in the armed state when the high resistance condition occurs, no display will take place until the system is disarmed. Wfig 2-Wti Smoke Detectors To Zone 1 1. Connect 2-wire smoke detectors across zone 1 terminals 8 (+) and 9 (-). Observe proper polarity when connecting the detectors (see Figure 7). 2. If an EOL resistor is presently connected across zone 1 terminals, remove it. The EOL resistor must be connected across the loop wires at the last detector. 3. See Programming Hard-Wired Zones later in this section for a detailed programming procedure. Teri& Operation of The control panel will verify any alarm by resetting the smoke detectors 2-Wire Smoke Detectors after the first alarm trigger, and then waiting 90 seconds for a second alarm in Zone 1 trigger. If the smoke detector or thermostat does not trigger again, the control will disregard the first trigger, and no alarm signal will occur. This feature eliminates false alarms due to electrical or physical transients. The ver@ feature is available on zone 1 only. This feature is available only on units that report to the downloader as Rev 4 or higher. -21-

Turning Off Fire Alarm You can turn off Fire alarm sounding by pressing the OFF key on any keypad or Sounding other arming/disarming device in that partition. To clear the memory of alarm and to reset the detector s alarm, enter the security code plus OFF again. b Compatible 2-Wire Smoke Detectors Detector Type Device Model # v Photoelectricw/heatsensor,directwire SystemSensor2300T Photoelectric,directwire SystemSensor2400 Photoelectricw/heatsensor,directwire SystemSensor2400TH Photoelectricw/B401Bbase SystemSensor2451 Photoelectricw/heatsensor& B401Bbase SystemSensor2451TH Ionization,directwire SystemSensor1400 Ionizationw/IMOIBbase SystemSensor1451 PhotoelectricductdetectorwLDH400base SystemSensor2451 Ionizationductdetect.wiDH400base SystemSensor1451DH r --------- 1 2-WIRE SMOKE UJ z L---------J IN ULINSTALLATIONS, ONLY ZONE 1 MAY BE USEO FOR FIRE. Figure 7. 2-Wine Smoke Detector Connected to Zone 1 Wdng 4-W- SmokdCombuetion Detectors on Zones 2-7 The system will support as many 4-wire detectors as can be powered from Auxiliary Power on the control on zones 2-7. Refer to the detector s instructions for complete details regarding its proper installation and w operation. 1. Connect 12 volt power for the detectors horn Auxiliary Power terminals 4 and 5, (which will interrupt power for fire alarm reset). Observe proper polarity when connecting detectors. 2. Connect detectors (includirw heat detectors. if used) across terminals of the zone selected (zones 2-7 may be used). W dete~rs must be wired in parallel. 3. To supervise power, we recommend the use of a System Sensor No. A77-716B supervisory module. F@re 8. 4-wire Smoke Detector Connection (Zonee 2-7) -22-

COMPATIBLE 4-WIRE SMOICWCOMBUSTION DETECTORS + 1412 System Sensor, 4-wire ionization. m oducts of combustion detector. I 2412 System Sensor, 4-wire photoelectric smoke detector 2412TH System Sensor, 4-wire photoelectric smoke detector w/135qf (57QC) heat detector A77-716B System Sensor, EOL relay module (supervisory module for wired 4wire fire zone). 2112/24T System Sensor low-profile 4-wire photoelectric smoke detector w/135qf (57QC) heat detector Whing 2-Wire Latching Glass Break Detectors On Zone S Use zone 8 for connection of compatible 2-wire latching-type glass break detectors. After an alarm, the first code + OFF turns off the siren and disarms the system; the second code + OFF clears the memory of alarm and resets the glassbreak detector. 1. Connect all detectors in parallel across zone 8 (terminals 19 and 20). Compatible Glass Break Detectors Use detectors that meet the following ratings: \Standby Voltage: 15VDC-13.8VDC Standby Resistance: Greater than 20k ohms (equivalent resistance of all detectors in paridlel) IAlarm Resistance: ILess than l.lk ohms (see note below) I Alarm Current: Reset Time: 2 ma-lo d Less than 6 seconds The IEI 735L series detectors have been tested and found to be compatible with these ratings. You can use up to fifty IEI 735L detectors, connected in parallel. You can use detectors which exceed 1.lk ohms in alarm, provided maintain a voltage drop in alarm of less than 3.8 volts. they GLASSBREAK DHEOTOR 2000 OHMS EOLR IJ%TCHINGTYPEGIASS BRE4KDEIECTORLOOP Figure 9. Glass Break Detector Connections To Zone S -23-

Progr amming Hard-Wwed Zones 1. With at least one 2-line Alpha keypad (5137AD or 6139) connected to the Partition 1 keypad terminals on the control, power up the system temporarily. If you had previously connected the AC transformer to the control panel, you need only plug in the transformer (to 120VAC outlet) to power up the system. 2. Enter the programming mode by keying the following on the Alpha keypad Installer code (41 12) + 8 + O+ O. Note that it is not possible to enter the programming mode if Partition 2 is in an armed state. 3. Press *56. Note that this is an interactive programming mode. You will use it to program zone numbers, zone types, partition numbers, alarm report codes, and to program response times for hard-wired zones. II Enter Upon entering *56 mode, this prompt will be Zn Num. displayed. Enter the first zone number that (00 = Quit) 01 II you wish to program (or [0][0] to exit zone programming). If you are starting with zone 2, enter 02. Press * to continue. Ilmicalsummarydimlay A summary display will appear, showing the present status of that zone s programming. Zn = zone number; ZT = zone type; P = partition to which zone is assigned; RC = report code for that zone; In= input type of zone; RT = response time for that zone. Values displayed are currently programmed values. If it is programmed satisfactorily, press [#] to back up one step and enter the next zone number, if desired. If you want to change a zone s programming, press [*]. A prompt for Zone Type will appear. J.Zone Number Each zone must be assigned a zone type, which defines the way in which the system responds 02 Zone Type to faults in that zone. A detailed explanation of IIPerimeter 03 each zone type is provided in Response Type II Definitions in Section 16. ZONE RESPONSE ZoneType ~ TYPE DEFINITIONS. Enter the desired zone type code, as listed below. 00. ZoneNot Used 07= 24 Hr Audible 01= Entry/Exit#1 08.24 Hr Aux 02= Entry/Exit#2 09= Fire (W/verif.)* 03= Perimeter 10= Interiorw/Delay 04= InteriorFollower 23= No Alarm 05. Trouble Day/AlarmNight Response 06= 24 HrSilent 24= SilentBurglary * The verification featureis only activewhen zone type 09 is assignedto hard-wiredzone 1. When the display shows the zone type you want, Dress [*1 to continue. -24-

n Enter the partition to which this zone is assigned, l or 2. The factory default is partition 1. Press [*] to continue. The report code consists of 2 hexadecimal digits, each in turn consisting of 2 numerical digits. For example, for a report code of 3C, enter [0][3] -1 for1~ad[l][2]f0rc. Re~er~oSectio7z15 SYSTEM COMMUNICATION for complete information on report codes, if necessary. Enter the desired report code and then press [*I to continue. 1 Enter the desired response time for the zone. ~~~~frj~5e~on.10msec,u~ Press [*] ;o continue. Typicalsummarydisplay A summary display will appear, showing the data for the zone that was just programmed. -l Con,ue If It M programmed satisfactorily, press [*] to ml The next request is to enter Alpha descriptors for the zones. The entry may be done now (enter 1) or may be done at a later time using X82 interactive mode (enter O).We recommend that the entry of Alpha descriptors be done using *2 mode. See Section 14. ALPHA DESCRIPTION PROGRAMMING for specific procedure If 0 (no) was entered above, the system will return to the Enter Zone Number prompt. Proceed with the programming for the next -zoneas.icatedpre.o.sly. Whe~ you have programmed all the hard-wired zones satisfactorily, exit *56 interactive mode at the Enter Zn Num. prompt by pressing [01[01* Then exit the programming mode by keying *99. Proceed to the check-out procedure that follows. -25-

Check-Out Procedure For Hard-Wwed Zones After installation of all hard-wired devices is completed, each partition of the security system should be checked, as follows. 1. Make certain that all devices and sensors connected to the hard-wired w zones are not in a faulted state. Doors and windows with contacts should be closed, PIRs should be covered (use a cloth to mask them temporarily if necessary). 2. Plug in the AC Transformer if you have not already done so.. 3. With all hard-wired zones intact, the Alpha keypad connected to the system should display: If the following is displayed, ~, press the [*] key to display the faulted zone(s). Restore any faulted zone(s) as necessary (also make sure that you have connected a 2000 ohm EOL resistor across the terminals of unused zones). When the DISARMED... READY TO ARM message is displayed, you can proceed to the next step. 4. Fault and then restore every contact or sensor on each zone individually to ensure that it is being monitored by the system. Each time a zone is faulted, the keypad should display the number of the faulted zone. When each zone is restored, the READY TO ARM message should appear again. If some hard-wired zones have been assigned to partition 1 and others to partition 2, you will need to observe the keypad in the appropriate partition as each zone in that partition is faulted and restored. 5. When you get the proper displays on the keypad(s), the hard-wired zones in the system are functioning properly. 6. Unplug the AC transformer. w -26-

This section provides information regarding the use of expansion modules for expanding the number of wired zones in the system, the modules that can be used and their wiring connections, plus a procedure for programming the wired expansion zones. Installing Zone Expansion Units You can add an additional 8 wired EOLR zones to the basic control s 8 zones, for a total of 16 wired zones, by using a No. 4219 Wired Expansion Unit, or 4229 Wired Expansion/Relay Unit. Location Supervision Zone Inforznation You can mount an expansion unit within the control cabinet if space permits. Otherwise, mount the unit outside the cabinet. Units are supervised against removal. Keypads will display CHECK and zone 09 if a zone expander is disconnected. Units have tamper protection for security when mounted outside of the cabinet. Assign zone numbers 10-17 for the eight wired expansion loops (designated A to H). You can program these zones individually (in *56 interactive mode) for Partition 1 or 2. See programming Wired Expansion Zones later in this section. Connections and Set-Up o~t+on 1. Connect the 4219 or 4229 module to the control s keypad terminals (see diagram below). - Set the 4219 or 4229 s DIP switch for device address l (switch 2 OFF and switches 3,4,5 ON ). Switch 1 determines expansion zone As response time ( ON = normal response, OFF = fast response). For location of the DIP switch in the unit, see the diagram below (location of DIP switch for both units is in the same location). For additional information, see instructions supplied with the 4219 and 4229. OL D (TERM S) ~RM 4) (TERM 5) (TERM 7) ZONES: A B CDEF GH Figure 10. WIMg Connections, 4219 & 4229 (4229 shown) -27-

Programming Wined Expansion Zones 1. With at least one 2-line Alpha keypad (5137AD or 6139) connected to the Partition 1 keypad terminals on the control, power up the system temporarily. If you had previously connected the AC transformer to the control panel, you need only plug in the transformer (to 120VAC outlet) to power up the system. 2. Enter the programming mode by keying the following on the Alpha keypad: Installer code (41 12) + 8 + O+ O. 3. Press *56. Note that this k an interactive programming mode. It is used to program zone numbers, zone types, partition numbers, and alsrm report codes for all zones that are going to be used. Enter the first zone number that you wish to program (or [01[01 to exit zone programming). Normally, you will be starting with zone 10, so enter 1O. Press [*] to continue. -LZoneNumber Ezziil A summary display will appear, showing the present status of that zone s programming. Zn = zone numbe~ ZT = zone @pw P = partition to which zone is assigned; RC = report code for that zone; In= input type of zone (AW for Aux Wired). L = Loop (not used for wired expansion zones) Values in the summary display are the currently programmed values. To start programming zone 10, press [*]. A prompt for Zone Type will appear. Each zone must be assigned a zone type, which defines the way in which the system responds to faults in that zone. A detailed explanation of each zone type is provided in Response ~pe Definitions in Section 16. ZONE RESPONSE TYPE DEFINITIONS. Enter the desired zone type,as listed below. 00= ZoneNotUsed 07= 24 Hr Audible 01= Entry/Exit#1 08=24 HrAux 02= Entrv/Exit#2 09= Fire 03= PeAeter 10= Interiorwillelay 04= InteriorFollower 23= No Alarm 05= TroubleDay/AlarmNight Response 06= 24 Hr Silent 24= SilentBurglary When the display shows the zone type you want, press [*] to continue. II 10 Partition II Enter the partition to which a zone is to be assigned. Enter l or 2. The default is partition 1. Press [*] to continue. -26-

10 Report Code 1st 03 2nd 12 3C Typicalsummarydisplay The report code consists of 2 hexadecimal digits, each in turn consisting of 2 numerical digits. For example, for a report code of 3C, enter [0][3] for 3 and [1][2] for C. Refer to Section 15. SYSTEM COMMUNICATION for complete information on report codes, if necessary. Enter the report code and then press [*] to continue. A summary display will appear, showing the data for the zone that was just programmed. Note that AW indicates an auxiliary wired (zone expansion module) zone. If it is programmed satisfactorily, press [*I to display the next prompt. For all zone types, the next request is to enter Alpha descriptors for the zones. The entry may be done now (enter 1) or maybe done at a later time usin *82 interactive mode (enter O). We recommen% that the entry of Alpha descriptors be done later using *82 interactive menu mode. See Section 14. ALPHA DESCRIPTION PROGRAMMING for specific procedure. lpretiously If O (No) was entered above, the system will display a prompt for entry of the next wired expansion zone number. Proceed with the programming for the next zone, as indicated When you have programmed all the wired expansion zones satisfactorily, exit *56 interactive mode at the Enter Zn Nurn. prompt by pressing [01 [01*. Then exit the programming mode by keying $4)!3. Proceed to the check-out procedure that follows. -28-

Check-Out Procedure For Wired Expansion Zones After you have completed installation of all devices, all expansion zones in each partition of the security system should be checked as follows: 1. Make certain that all devices and sensors connected to the wired ~ expansion zones are not in a faulted state. Doors and windows with contacts should be closed, PIRs should be covered (use a cloth to mask them temporarily if necessary). 2. With all zones intact (including hard-wired zones), the Alpha keypad connected to the system should display: ~~ If the following is displayed, ~, 3. 4. 5. press the [*] key to display the faulted zone(s). Restore any faulted zone(s) as necessary (also make sure that you have comected a 1000 ohm EOL resistor across the terminals of unused expansion zones on the 4219 or 4229 module). When the READY TO ARM message is displayed, you can proceed to the next step. Fault and restore every contact or sensor in each expansion zone individually to ensure that it is being monitored by the system. Each time a zone is faulted, the keypad should display the number of the faulted zone (as programmed by you just previously in *56 mode). When each zone is restored, the READY TO ARM message should appear again. If some wired expansion zones have been assigned to partition 1 and w others to partition 2, you will need to observe the keypad in the appropriate partition as each zone in that partition is faulted and restored. When you get the proper displays on the keypad(s), the wired expansion zones in the system are fimctioning properly. Unplug the AC transformer.. -30-

Relay/Powerline Carner Device Basics Relays and Powerline Carrier devices (ex. X-10 brand devices) are programmable switches that can be used to perform many different fbnctions. They can be used to turn lights on and off, control sounders, or for status indications. In this system, each device must be programmed as to how to act (ACTION), when to activate (START), and when to deactivate (STOP). Each of these is described below, and in the programming procedure for *8O and *81 interactive modes that are provided at the end of this section. The control supports a total of 8 output devices in the following configurations: One 4204 relay module (4 relays) and 4 Powerline Carrier devices. One 4229 zone/relay module (2 relays) and 6 Powerline Carrier devices. Up to 8 Powerline Carrier devices (8 minus the number of output relays used). The 4204 and 4229 modules provide Form C (normally open and normally closed) contacts. Powerline Carrier devices are controlled by, signals sent through the electrical wiring at the premises via a 4300 transformer. Therefore, if using Powerline Carrier Devices, a 4300 transformer must be used in place of the regular system transformer. 4204 and 4229 Relay Modules 4204/4229 -p In *8O and *81 interactive modes, a series of keypad prompts will request entries for programming of the Relay outputs and/or Powerline Carrier devices used in the system. Refer also to OUTPUT REIAYS/POWERLINE CARRIER DEVICES WORKSHEET FOR *8O AND *81 INTERACTIVE MODES in the blank progmunming form. The 4204 or 4229 unit can be mounted either remotely or in the control panel. The following steps should be taken to properly setup the 4204 or 4229: 1. Connect the 4204/4229 to the control s Partition 1 remote keypad terminals (4-7), using the connector supplied with the 4204 and 4229. Use standard 4-conductor twisted cable for long wiring runs. See Figures 11 and 12. 2. 3. Set the 4204/4229 s DIP switch for a device address of l (switch 2 OFF and switches 3, 4, 5 ON ). Switch 1 determines the unit s cover tamper response ( ON = disabled, 0~ = enabled). Connect the desired field wiring to the unit s relay contact terminals. Supervision 4204 and 4229 modules are supervised against removal. CHECK and zone 09 will be displayed if a module is disconnected from the control s terminals (4, 5,6, & 7). -31-

4229 GRN DATA OUT (TERM 6) ~ TO CONTROL (-) GROUND (TERM 4) B (+) 12V (TERM 5) YEL DATA IN FROM CONTROL (TERM 7) R ZONES A B c ~ E F G ~ Figure 11. 4229 Connection to Control.4204 R51AY 4 = + MPS~H TYPICAL i FOR SEillNG DEVICE ADDRESS (SHOWN WF ) AND ENASUNGIDISASUffi TAMPER TS2 COVER TAMPER (REED) SWITCH 1 4-PIN CONSOLE PLUG & 0 Tsl L L ~ DATA IN FROM CONTROL (term. T) Bti [-) GROUND (tmm4) OATA OUT TO CONTROL RED (+) 12V (twii. 5) (term. 6) Figure 12. 4204 Connection to Control Powerline Carrier devices The 4300 transformer provides AC power to the control panel, and also supplies signals from the control panel through the premises AC wiring to the Powerline Carrier devices (which are plugged into AC outlets). Devices plugged into Powerline Carrier devices can then be made to perform various functions in response to commands entered at the keypads in the security system. -32-

Wting Connection 1. Splice one end of a 3-conductor cable to the wire ends of the 4142TR cable supplied with the 4300 transformer. 2. Connect the 4142TR cable plug to the 9-pin connector on the control (see SUMMARY OF CONNECTIONS diagram for location of the 9-pin connector), 3. Connect the other end of the 3-conductor cable to the 4300 transformer, as indicated in the table below and in the diagram that follows. 4300 TRANSFORMER WIRE CONNECTIONS 4300 TERMINAL ITO IX-AL ON CONTROL 1 (AC) 1 (16.5VAC in) 2 (Ground) 25 EarthGroundterminal 3 (AC) 2 (16.5VAC in) 4300 TERMINAL 4142TR CABLE WIRE 4 (sync) RED (Pin5 of 9-pinconnector) 5 (Data) VIOLET(Pin 1 of 9-pinconnector) 6 (Corn) WHITE(Pin4 of9-pin comector) 4300 TRANSFORMSWINTERFACE Figure 13.4300 Transformer Wag Connection -33-

Programming Options Defined The following will help you understand the programming of OUTPUT DEVICES when using *8O and *81 modes. The options used to start and stop these devices are described below, followed by the actual screen prompts and available entries. The letter(s) in parentheses after each fiction described below, such as (A) after ACTION, are those that appear in the various summary displays of programmed data during programming. w ACTION (A) The ACTION of the device is how the device will respond when it is activated by the START programming. You may want the device to activate momentarily, to pulse on and off continuously, or to remain activated until some other event occurs to stop it. There are four different choices of actions: ACTIVATE for 2 SECONDS and then reset. ACTIVATE and REMAIN ACTIYATED until stopped by some other event. PULSE ON and OFF until stopped by some other event. NOT USED when the device is not used. START (STT) The START programming determines when and under what conditions the device will be activated. The following START options are available: A) 1. EVENT (EV) is the condition (Alarm, Fault, Trouble) that must occur to a zone or group of zones (zone list) in order to activate the device. These conditions apply only when a zone list is used. The different choices for EVENT are listed below and in the Programming Output Relays & Powerline Carrier devices section that follows. ALARM Relay action begins upon any alarm in an assigned zone in the zone list. FAULT Relay action begins upon any opening or short in an assigned zone in the zone list. c TROUBLE Relay action begins upon any trouble condition in an assigned zone in the zone list. c NOT USED Relay action is not dependent upon one of the above events. 2. ZONE LIST (ZL) is a group of zones to which the EVENT applies in order to activate a particular device. Note that there are a total of 3 zone lists that can be programmed in field *81 mode; when the selected EVENT (Alarm, Fault or Trouble) occurs in any zone in the selected Start ZONE LIST (1, 2, or 3), activation of the selected device will START. B) 1. ZONE TYPE/SYSTEM OPERATION (ZT). If a System Operation, such as DISARMING or ANY FIRE ALARM, is to activate the device, the appropriate choice would also be entered under the ZONE TYPE option. ZONE TYPE is used independently of the EVENT/ZONE LIST combination. If a specific ZONE TYFE is chosen, any zone of that response type going into alarm, trouble, or fault will cause the device to activate as selected in ACTION. If the same., ZONE TYPE is also chosen for the STOP programming, any zone of that type that restores will de-activate the device. w

2 STOP (STP): A) 1. B). 1. 2. If a SYSTEM OPERATION is chosen (e.g., End of Exit Time), that operation will cause the device to activate as selected in ACTION. The different choices for ZONE TYPE and SYSTEM OPERATION are listed in Programming Output Relays & Powerline Carrier devices later in this section, and in the Programming Form. PARTITION No. (P). The device s Start ZONE TYPE/SYSTEM OPERATION may be limited to an occurrence on Partition 1, Partition 2, or any partition (A). The STOP programming determines when and under what conditions the device will be de-activated. The following options are available: RESTORE ZONE LIST (zl). If a ZONE LIST is used as the Stop event, the device will de-activate when all the zones in that list restore from a previous fault, trouble, or alarm condition. This will occur regardless of what is programmed to START the device; therefore, a RESTORE ZONE LIST would normally only be used when a ZONE LIST is used to start the device. ZONE TYPE/SYSTEM OPERATION (ZT). Instead of using a RESTORE ZONE LIST, a specific zone (response) type or system operation action can be selected to deactivate the device. If a specific ZONE TYPE is chosen, any zone of that response @e that restores born a previous alarm, trouble, or fault condition will cause the device to de-activate, If a SYSTEM OPERATION is chosen, that operation will cause the. device to de-activate. The dmerent choices for ZONE TYPE and SYSTEM OPERATION are listed in programming Relays & Powerline Carrier devices later in this section, and in the Programming Form. PARTITION No. (P). The device s Sto~ Zone -35-

Programming Output Relays and Powerline Carrier Devices 1. With at least one 2-line Alpha keypad (5137AD or 6139) connected to the Partition 1 keypad terminals on the control, power up the system temporarily. If you had previously connected the AC transformer to the control panel, you need only plug in the transformer (to 120VAC outlet) to power up the system. 2. Enter the programming mode by keying the following on the Alpha keypad: Installer code (41 12) +8+ O + O. OutputDevice Displays ~ ~, lkt?zq 3. Press *7. POWERLINE CARRIER DEVICE HOUSE ID. Enter House ID 1-15 for Powerline Carrier devices, as follows: 0= A,l=B,2= C,3=D,4= E,5=F,6=G,7 =H,8=I,9=J,#+ 1O=I-$ #+ll=l, #+12= M,#+13=N, #+ 14=0, #+15=P. Default is O. The House ID must match the House ID set on the powerline carrier devices. The unit ID for these devices is 1-8 depending on which device is being programmed. For example, device #1 must be set to unit ID 01, device #2 to unit ID 02, etc. 4. Press *80. Note that this is an interactive programming mode. It is used to program all output devices used in the system (4229 or 4204 Relay modules, or Powerline Carrier devices). Refer to the Programming Form worksheet for *8O Interactive Mode. Upon pressing *80, this screen will appear. Enter the Device Number 01 or 02 for a 4229, or 01, 02, 03, or 04 for a 4204, or 01-08 for Powerline Carrier 01 devices (or 00 to end these entries). Press the [*I key to continue. The [*] key is used to accept an entry and advance to the next prompt. The [#] key is used to revert back to the last question to check or change an entry. Press [*] to go forward again. This screen displays a stimary of the current Device START programming (for this example, device 02 has been selected). Press the [*] key to continue. ~ I This screen displays a summary of the current Device STOP programming. 02 AEVZLZT P Press the [*] key to continue. STP - -0001 II m II II 02 StarE No List Zn List o II Enter the desired device action as listed below. Press the [*] key to continue. O= No response 2 = Close and Stay Closed 1 = Close for 2 seconds 3 = Continuous Pulse on & off (1 sec ON, 1 sec OFF) Enter the event to START the relay O= Not used 2 = Fault; 1 = Alarm; 3 = Trouble A zone list must be used in conjunction with an event. If a zone type/system operation is to be used instead of an event, enter O. Press the [*] key to continue. If a zone list will be used to START the relay action, enter the zone list number (to be programmed in field *81): 1, 2, or 3. If not used, enter O.Press the [*] key to continue. If a zone type or system operation will be used to START the device action, 02 Start: Zn Typ enter the appropriate two-digit code (see table that follows). If not, enter 00. Not Used 00 II Press the [*] key to continue. -36-

CHOICES FOR ZONE TYPES 00= NotUsed 04= InteriorFollower 08=24 HrAux 01= Entry/Exit#l 05= TroubleDay/AlarmNight 09= FireTrouble I 02= Entry/Exit#2 06= 24HrSilent 10= Interiorw/Delay 03= Perimeter 07= 24HrAudible 23. NoAlarmResponse 24. SilentBurglary ** Use O(Any) for PartitionNo. (P) entry. * * Or at Disarming, whicheveroccurs earlier. ~ CHOICES FOR SYSTEM OPERATION 20= Arming+tay 36= **AtBellTimeout*** 42= **SystemBatteryLow 21. Arming-Away 38= Chime 43= Communication Failure 22. Disarming(Code+ OFF) 39= AnyFireAlarm 52= KiSSOff 31= EndofExitTime 40= Bypassing 58= Duress 32= StartofEntryTime 41= **ACPowerFailure 33= AnyBurglaryAlarm Enter (if applicable) the partition number 1 or 2 (or Ofor any). Press the [*] key to continue. 02 stop: Zn List No List o I 02 stop: Zn Typ Not Used 00 I If a zone list will be used to STOP, or restore, the device action, enter the zone list number 1,2, or 3 (to be programmed in *81 mode). If not used, enter O. Press the [*] key to continue. If a zone type or system operation will be used to STOP the device action, enter the appropriate two digit code (see the ZT choices listed above). If not, enter 00. Press the [*] key to continue. 02 stop: Part Any Partition 02.AEVZLZT P S1-roooool A Enter (if applicable) the partition number 1 or 2 (or Ofor any). Press the [*I key to continue. This screen again displays a summary of the current device START programming. Press the [*] key to continue. This screen again displays a summary of the current device STOP programming. Press the [*] key to continue. Enter 1 if using a Powerline Carrier Device (X-1O); if not, enter O. The display then returns again to the first screen so that the next device number to be programmed can be entered, or enter [0][0] to end device Example of A lamp is to be turned on via a Powerline Carrier device (X-1O) when any one Output Device of 3 specific zones sxe faulted, or when any 24hour auxiliary zone is faulted. Programming We want to be able to turn off the lamp manually without affecting the arming status of the system. To program this, we would do the following. In *8O interactive mode we choose output Device 01 and program the Action (A) to be 2 (Close and stay closed). The Event we are looking for to start the Device action is a fault, so we will program 2 in (EV). We will use Zone List 1 for the 3 specific zones, so we will program l in (ZL), (and we will program these 3 zones in *81 s Zone List 1). The second condition for turning on the indicator is triggering a 24-hour aux. zone (Zone Type 08), so we will program (ZT) as 08. Next, enter the Partition number (P) in which you want the triggering of a 24hour zone to occuq enter 1 or 2, or enter Ofor any partition. -37-

ZoneListDisplays ~ ~] To stop the Device action and turn off the lamp, we do not want to use a restore of any zone, so a O will be programmed for the Restore of Zone List (ZL). We will use a manual entry of User Code + [#] + [8] + Device # to turn off. Therefore, we do not need to program a STOP event. Press [*I to continue. The system will display a summary screen for the START programming for device 01. Press [*I to continue. The system will display a summary screen for the STOP programming for device 01. Press [*I to continue. The system will display the X1O? prompt. Enter 1 for yes. The Enter Device No. prompt for the next zone will be displayed. Press 00 and then [*] to exit the *8O mode. Now use *81 Zone List mode to program the 3 specific zones in Zone List 1. Press *81. (Zone Lists for Output Devices). This interactive mode is applicable only if you have programmed MO mode. Refer to the Programming Form worksheet for *81 Mode. Upon keying *81, this screen will appear. Enter the Zone List Number 01,02, or 03 to program (or 00 to end these entries). Press the [*] key to advance. In the following displays, zone list 01 has been selected for programming, Enter each zone number to add to the zone list by first entering the zone number, then the [*] key (example, 01*, 02*, 03*). After all zones desired are entered, press 00 to advance. - To delete the zone list, enter 1 (Yes). All zones in the zone list will be deleted 01 Del Zn List? automatically. and programming will return to the first screen. O= Nol=Yes O To save the zone @t, enter () (N;) to advmce. w To save the entire zone list, enter O(No) and programming will return to the ~ lfktscreeil O To delete a zone or zones ~ a zone list enter I ~es) to advace. IF===ll Enter each zone to be deleted fkom the list, followed by the [*] key. After all zones to be deleted are entered, enter 00 to return to the first screen so that I (00= Quit) 00 another list can be programmed, if desired. Notes: Any list may include any or all of the system s zone numbers. A zone list can be assigned to more than one output relay. If you only want to review what has been programmed previously, enter [#1[8][11.The review can be advanced by using the [*] key. When finished, enter [01[0] *to quit. No programmed values can be changed in this mode. When programming in *8O and *81 interactive modes is completed, exit the programming mode by keying *99. Unplug the AC transformer.

Installing the 4285 This section provides instructions for mounting the 4285 VIP(VISTA Interactive Phone) module, wiring the 4285 Module and for programming the system for phone access via the 4285 Module. Module General Information The 4285 VIP module is an add-on accessory for the VISTA-20HW that permits access to the security system via a Touch-tone phone (either on premises or by a call-in when away). The 4285 can amounce many of the same words that would normally be displayed on an Alpha keypad under the same system conditions. When properly comected, the 4285 module will enable the user to do the following via a Touch-tone telephone: a. Receive synthesized voice messages over the phone regarding the status of the security system. b. Arm and disarm the security system and perform most other commands using the telephone keypad, with voice annunciation being provided over the phone as confirmation after any command is entered. The phone used for phone access must have Touch-tone capability, though Touch-tone service is not necessary (if premises uses PULSE dialing, switchable phones must be set for Touch-tone temporarily before attempting phone access). A Phone Access User s Guide for phone access to the security system is provided with the 4285 module for the user of the system. Mounting The 42S5 Module The 4285 module may be mounted in the control cabinet if space is available or, if this is not possible, on the side of the cabinet or adjacent to it. When mounting the module outside the cabinet, use the screw holes at its rear which will permit it to be mounted horizontally or vertically (2-faced adhesive tape may be used, if preferred). Wires can be brought out horn the side or back (a round breakout is also available on the back). Affix the 4285 module s connections label (supplied separately) to the inside of the module s cover if the cover is used. If you have installed the module within the cabinet, & the label to the inside of the control cabinet s door. -39-

4285 Module WIMg The 4285 is wired between the control panel and the premises handset(s). It listens for touch tones on the phone line and reports them to the control panel. During on-premises phone access, it powers the premises phones; during off-premises phone access, it seizes the line from the premises phones and any answering machines. Note: The phone lines must be in service for the 4285 module to function, even when accessing the systemfrom an on-premises phone. 1. Make 12V (+) and ( ) and data in and data out comections from the 4285 module to the control, using the connector cable supplied with the 4285 (see Figure 16). WI * These are the same connections as those usedfor remotekeypads connectedto Partition1. ~ \ YELLOW I DATAOUT(terminal7) ~ 2. Insert the keyed connector at the other end of the connector cable into the 4285Terminal 4285 WIRING TABLE I I COMeCtStO: I 1. PhoneIn (Tip) Terminal(23) oncontrol. 2. PhoneIn (Ring) Termiml (24) oncontrol. 3. PhoneOut(Tip) BROWNleadfromdirect-connectcord. 4. PhoneOut(Ring) GRAYleadfromdirect-connectcord. 5. Ground Earthgroundterminal(25)on control. r 6.Not Used 7.Not Used Caller ID Units If the telephone system on the premises includes a Caller ID unit, connect the Caller ID unit directly to the Handset terminals (21 &22) on the control as shown in 4285 Wiring Connections diagram that follows. 40-

1. 2. 3. 4. 5. 4285 WIRING NOTES Wire the 4285 moduleexactlyas shown,usinga direct-connectcord and RJ31Xjack. If Touch-tonesare not heard whenpressingkeys followingphone access to the securitysystem viu an on-premisesphone, try reversingthepairof wires connectedto terminals3 & 4 on the 4285, and the pairof wirescomected to terminals21 &22 on thecontrol. If an error signal (fastbusy signal)is heardwhen tryingto accessthe systemvia the phone, check for correctline seizurewiring,asdescribedin note4. Comection to the incoming Telcoline via a RJ31Xjack and direct-connectcord, as shown in this diagram,is essential,even if the systemis not connectedto a central station.the 4285 will not function if this is not done. The house phone lines (gray and brown wires) must be wired to the 4285 terminals, not to the control terminals. Otherwise, an error signal (fast busy signal) will occur when trying to access the system fkom an on-premises phone. If the telephone system on the premisesincludes a Caller ID unit, connect the Caller ID unit directly to the Handset terminals(21& 22)on the control,as shown. r - - -----Ti-xiii7iNw---------. ;IF THE PANEL IS NOT CONNECTED TO ~ o z!a PROPER EARTH GROUND,YOU MAY ~ Incomina ~ iget FALSE LINE CUT INDICATIONS (IF : PREMISESANSWERING MACHINEAND PHONES NOT INSTALLER < 0 ADJUSTABLE ~1 * ~Igure 14. 42S5 VtP Module Wfig CoMectiona iq KEYED H ii HEADER *NOTE:IF THE TELEPHONE HAS BUILT-IN CALLER I ID, THE CALLER ID FUNCTION MAY NOT WORK. I UNUSED YELLOW: TO DATAOUT (term. 7) TO CONTROL ~.-----.-- -------------------- 1 42S6 NOCONNECTION PANEL I 1 CONNECTOR RED TO AUX (+) (term.5) TERMINALS I TERMINAL ASSIGNMENTS! WITH FLYING - BLACK TO AUX.GROUND(-) (term.4) USED FOR ~1 -TIP I ) PHONE INPUT I LEADS E GREEN: TO DATAIN(term.6) ~ 2- RING I 1 KEYPAD 13-TIP CONNECTIONS PHONE OUTPUT i ; 4- RING } ~ 5- GROUND I ;6- I AUDIO OUT 1 ~7- } L--------------------- (FOR FUTURE USE).------- j 41-

Programming The Control For Phone Access 1. With at least one 2-line Alpha keypad (5137AD or 6139) connected to the Partition 1 keypad terminals on the control, power up the system temporarily. If you had previously connected the AC transformer to the w control panel, you need only plug in the transformer (to 120VAC outlet) to power up the system. 2. Enter the programming mode by keying the following on the Alpha keypad: Installer code (41 12) + 8 + O + O. 3. Press *28. VOICE MODULE ACCESS CODE. m If using a 4285 VIP module, enter the 2-digit phone access code as follows: For first digit, enter 1 9; for second digit, enter # +11 for W, or # +12 for #. Example: if desired access code is 7*, 7 is the first entry, and # + 11 (for*) is the second entry. Enter 00 if not using a 4285 module (this is the default). Note: A O in either digit will disable thew Voice Module. 4. Press *5. RING DETECTION COUNT. ril 1 ) Refer to the chart below and program this field accordingly. I Voice Answering Module Machine Downloading Field *95 Programming Yes No No Setforvalueotherthan O (1-15). Thiswillenablethe controlpanelto answerthe phonecall. Otherwise,it will not be possible to access the 4285module. Yes Yes No Set for a value higher than the number of rings for which the answeringmachineis set. Example: if machine is set for 4 rings, use a value of 5 or higher. This is recommended so that the 4285 module can stillbe accessedif the answering machine is turned off and does not answerthe phonecall. Yes No Yes Setforvalueotherthan 0 (1-15). Yes Yes Yes Enter 15 t.abypass the answering machine. w 5. Zone descriptors should also be programmed, regardless of the type of keypads in use. If this is not done, the 4285 module will not annunciate a description of the zone(s) in alarm, trouble, etc. (the 4285 will annunciate zone numbers only). You can enter zone descriptors now using interactive mode *82, or later. See the Section 14. ALPHA DESCRIPTION PROGRAMMING for a detailed procedure. 6. Exit the programming mode by entering *99. Perform a preliminary check of the 4285 module, as indicated next. --42-

Checking the Operation of the 42?35 VIP Module To Check Operation From an On-Premiees Phone: 1. Pick up phone and enter the programmed 2-digit phone code. Annunciation of a system statusreport should automatically start. See the User s Guide accompanying the 4285 module for detailed information regarding the nature of the status report, if necessary. 2. During any pause in the status report, or immediately following it, key the following via the keypad on the phone: Installer Code (4112), then press key 1 (OFF). 3. A beep should be heard on the phone and from a wired keypad, and the words DISARMED...READY TO ARM or DISARMED...NOT READY TO ARM* should be heard, indicating that the command was entered successfully. * DISARMED...NOTREADYTO ARMwouldindicatean open zone. 4. Hangup the phone. To Check Operation From an Off-Premieee Phone: 1. Have someone dial the premises phone number, using a TouchTone phone.. If the phone system does not include an answering machine, 2 long tones will be heard in the caller s phone, followed by a voice prompt!hello, ENTER PHONE CODE NOW. The caller should enter the programmed 2-digit phone code. Q If the premises phone system includes an answering machine, the 2- digit phone code should be entered during a pause at the beginning of, or during, the outgoing answering machine message. 2. 3. 4. 5 6. 7. 8. 9. When the 2-digit phone code is entered, the caller will hear a voice prompt asking for entry of the 4-digit system code ( ENTER SYSTEM CODE NOW ). The caller should then enter the installer code (4112). As a safety feature, there is a 3-try limit in which to enter each code (phone code and system code), after which time the call-in will be aborted. Also, if no keys are pressed for a period of 20 seconds, the call-in will be aborted. Annunciation of a system status report will start if both codes were entered correctly. During any pause in the status report, or immediately following it, the caller should key the following via the keypad on the phone: Installer Code (4112), then 1 (OFF). A beep should be heard (and from a wired keypad on the premises), and the words DISARMED...READY TO ARM or DISARMED...NOT READY TO ARM* should be heard on the caller s phone, indicating that the command was entered successfully. * DISARMED...NOTREADYTOARMwouldindicatean openzone. At this point, the caller can hangup the phone. Ve@ with the caller that there was successful access to the system and that the appropriate annunciations were heard over the phone. If the 4285 module fimctioned satisfactorily, unplug the AC transformer from the AC outlet.

This section provides a Iist of compatible sounders, comection information for an external sounder and programming procedures for those options that affect the operation of external sounders. Compatible Sounders Ademco AB-12M 10 Motor bell & box. UL Grade A. 100 ma Motorized Bell & Box current draw. Ademco 1011BE12M Motor bell & box. UL Listed. 100 ma current 1(Y Motorized Bell& draw. Box Ademco Self-contained 6-12 volt siren (driver builtiin) 702 Outdoor Siren and weatherproof for outdoor use. Can be wired for either a steady or warble sound. Ademco 719 Two-channel, self-contained 6-12-volt siren 2-Channel Siren (driver built in). 109W3@ 10 feet. 550mA current draw. Ademco 747 Self-contained 12 volt siren (driver built-in) Indoor Siren for indoor wall mount. 747F available for flush mounting. Ademco 747UL Self-contained siren (driver built-in) for indoor Indoor Siren wall mount. UL Listed. Ademco 744 6 jumper-selected sound outputs. Rated at Siren Driver l19db with use of an 8-ohm 30 watt speaker. Ademco 745X3 Voice siren driver with English, Spanish and Voice Siren Driver French voice messages. Separate messages for Fire and Burglary. Use with 8-ohm speaker. UL Listed. Ademco 705-820, 15-watt, 8-ohm speaker. 5-inch Round Speaker Ademco 713 Speaker 40-watt, 8-ohm, indoorloutdoor speaker. System Sensor PA400B Indoor piezo sounder (red or beige), rated at (beige)/pa400r (red) 90 db @ 10 feet. Indoor Fiezo Sounder w This control complies with NFPA requirements for temporal pulse sounding of fire notification appliances. Temporal pulse sounding for a fire alarm consists of the following: 3 pulses - pause 3 pulses pause -3 pulses... -44-

Sounder Connections The VISTA-20HW provides a 12 VDC output which can power external alarm sounders (bells or sirens, see compatible sounders listed previously). This output will activate a sounder when an alarm occurs in partition 1 or 2. Make connections to alarm output terminals 3 (+) and 4 (-). See diagram below. Non-UL hmttdkttiolls The total current drawn from this output cannot exceed 2 amps. A battery must be installed since this current is supplied by the battery. CONTROL BOARD + No. 702 SIREN OUTPUT Figure 15. Typical Sounder Wtig Programming for External Sounders 1. 2. 3. 4. 5. 6. 7. With at least one 2-line Alpha keypad (5137AD or 6139) connected to the Partition 1 keypad terminals on the control, power up the system temporarily. If you had previously comected the AC transformer to the control panel, you need only plug in the transformer (to 120VAC outlet) to power up the system. Enter the programming mode by keying the following on the Alpha keypad Installer code (41 12) + 8 0 0. Press %2. (Single Alarm Sounding per Zone/Armed Period). Enter 1 for yes, O for no (default). Enter O for UL installations. Press =3. (Fire Sounder Timeout). Enter 1 for no timeout, O for timeout (default). Press *4. (Alarm Bell Timeout). Enter Ofor no timeout, 1 for 4 min (default), 2 for 8 rein, or 3 for 12 min. Enter 1 for UL installations. Press =7. (Confirmation of Arming Ding). m There are separate entries in this field for partition 1 and for partition 2. Enter O for no (default), 1 for yes. Exit the programming mode by entering *99. I I 4s-

After installation of the sounder is completed, each partition of the Security System should be carefully tested, as follows. 1. Connect the battery wires from the control board to the battery, observing correct polarity. 2. Enter the installer code (4112) and press the TEST [5] key on the keypad. The external sounder should sound for 1 second if the sounder is good and proper connections have been made. Note that if the backup battery is discharged, the sounder will not turn on. 3. To turn off the test mode, enter the installer code (4112) and press the OFF key. 4. Disconnect the battery wires from the battery terminals. 5. Unplug the AC transformer from the AC outlet. w -46-

Generel Information Check availability of Model 7720PLUS or 7820 long range radio. If output to long range radio is selected, all messages that are programmed to go to the primary telephone line receiver will also be sent to the 7720 PLUS or 7820 long range radio. These messages will be in Contact ID format (not fiected by entry in field *48). I The data line is supervised, as well as certain functions in the radio. If communication is lost or a trouble develops, a message will be attempted to be sent via both radio and telephone to the central station. For complete information, see the manual that accompanies the radio. I Connection Connect the data in/data out terminals and voltage input terminals of the No. 7720 PLUS or 7820 Long Range Radio to the control s keypad connection points, terminals 4, 5,6, and 7 as shown below. BL4CK RED o5 GREEN 7720PLUS17S20 6 LONG RANGE RADIO 0 YELLow o7 CONTROL TERMINALS Figure 16. Long Range Radio Connections 1. 2. 3. 4. 5. 6. With at least one 2-line Alpha keypad (5137AD or 6139) connected to the Partition 1 keypad terminals on the control, power up the system temporarily. If you had previously connected the AC transformer to the control panel, you need only plug in the transformer (to 120VAC outlet) to power up the system. Enter the programming mode by keying the following on the Alpha keypad Installer code (41 12) + 80 0. Press *29 OUTPUT TO LONG RANGE RADIO u Enter the first digit of the trouble dialer report. The 2nd digit of the code entered in field MO is automatically sent as the second digit of this code. Program the 7720 PLUS or 7820 radio for device address 3. Exit the programming mode by keying *99. I 47-

This section provides instructions for the connection of an optional remote 4146 keyswitch for remote arming and disarming of the system, and the programming necessary when a keyswitch is used. Also included is a description of how the keyswitch operates in the system. _ Installing the Keyswitcb The remote 4146 keyswitch (with red and green LEDs to indicate status) is connected to zone 7. Note that you can use a keyswitch in one partition only. Remote Keyswitch Connections 1. Connect the 4146 keyswitchs normally open momentary switch to zone 7 terminals (18 and 19). Remove the 2000 ohm EOL resistor if connected across zone 7 terminals. 2. 3. 4. Connect the Red and Green LEDs to pins 7, 8, and 9 on the 9-pin connector, using a 4142TR cable as shown in Figures 17 (A) and (B). Connect a 2000 ohm EOL resistor across the momentary switch. You can wire an optional closed-circuit tamper switch (model 112) in series with the zone: If the switchplate is then-removed fi-om the wall, the tamper will open, disabling keyswitch operation until the system is next disarmed fi-omthe keypad. If the tamper (or zone 7 loop wires) is opened when the system is armed, an alarm will occur. 48-

9 PIN CONNECTOR ON CONTROL BOARD f \ ~m i j { THESE WIRES NOT 4142TR CABLE CONNECTEO IF 4300 INTERFACE \ \ + AUX POWER TRANSFORMER IS m BEING USED. -------- BROKEN LINES REPRESENT INSTALLER WIRING CONNECTIONS m(armed) (REAOY) ~..-. ---.. ----...-. -....-..--... RED GREEN \ ---- 62022 620Q ----++---J F4-----------a; I ~------- ~----------- --------------7 fifik-----------j ---b LOCK! TO ZONE 7 SWTCH(N.O.) : TO TERM 19 ------------- I l??\ ------J 0 j e--------!2000 OHMS ~------------ 4146 KEYSWITCH $ EO1 Figure 17 (A). Keyswitcb Whing (4300 Interface Transformer not used) OJl r 1 I 1, 123456789 9 PIN CONNECTOR ON CONTROL BOARD $ $ ~ g ~ # f g g g g a g m m m BROKEN LINES REPRESENT INSTALLER WIRING CONNECTIONS l ERMlNu6 ONcoMmol SOARD c ) NOTUSED Ml w3e0 4142TR CABLE (ARMED) (lwadyj,-----------. -.-----. ---. -.---., RED GREEN \ L + AUX POWER ---------.-- f / k 820Q 8200 ~:::::: :e.-tamper SW17CH (N.C.). TO TERM 16 ------------- * --.----1 o LOCK TO ZONE 7 SW17CH (N.O.) i TO TERM 19 [ ~ -------------- *\ ----.--, u : -------- am OHMS EOLR 4146 KEYSWITCH Figure 17 (B). Keyswitcb Wining (4300 Interface Transformer also used)............- $ -49-

Programming For The Remote Keyswitch 1. With at least one 2-line Alpha keypad (5137AD or 6139) connected to the Partition 1 terminals, power up the system. If you had previously connected the AC transformer to the control panel, you need only plug in the transformer (to 120VAC outlet) to power up the system. 2. Enter the programming mode by entering: Installer code (41 12) + 8 + O + Okeys. Note: If keyswitch is enabled, in menu mode *56 the Zone Type (ZT) for zone 7 will show 77, and will not be accessible for programming. 3. Press *56. Note that this is an interactive programming mode. You will use it to program zone 7 for partition number, alarm report codes, and to program response time (zone type will automatically show as 77 ). ml ZoneNumber~ Typicalsummarydisplay II ZnZTPRCln RT Zn = zone numbeq 0777 1 00 HW: 1 II ZT = zone type; J Zone Number II 07 Zone Type 77 II ZoneType 1 Upon entering *56 mode, this prompt will be displayed. Enter zone number 07 (if not already present). Following this entry, press *to continue. A summary display will appear, showing the present status of zone 7 s programming. P = partition to which zone is assigned RC = report code for that zone; In= input type of zone; RT = response time for that zone. Values displayed are the factory defaults for zone 7 or, if this is not a new installation, they are the currently programmed values. To program zone 7, press [*I. Zone type will be automatically displayed as 77, and no entry is required. Press [*] to continue. II 07 Partition 1 II The partition to which the keyswitch is assigned is entered here. Enter l or 2. Note that thekeyswitch arming may only be used in one partition. (Default = [1]. Press [*] to continue. The report code consists of 2 hexadecimal digits, each in turn consisting of 2 numerical digits. For example, for a report code of 3C, enter [01[31for 3 and [11[21for C. If necessary, refer to Section 15. SYSTEM COMMUNICATION for complete information on report codes. Enter the desired numbers and then press [*] to continue. -50-

I m 07 Response Time 1 II Typicalsummarydisplay I Program Alpha? O= Nol= Yes O I Enter the desired response time for zone 7. The recommended entry for keyswitch operation is 1 (the factory default). Selections available are: 0 (10 msec), 1 (350 msec), or 2 (700 msec). Enter the desired numbers and then press [*I to continue. A summary display will appear, showing the data for zone 7 that was just programmed. If it is programmed satisfactorily, press [*I to continue. The next request is to enter an Alpha descriptor for zone 7. Since this is a keyswitch zone, no descriptor is required. Enter O. If O (no) was entered above, the system will display a prompt for entry of the number for the next zone. Press [01[01plus [*I to exit *56 mode. Exit the prograrnrning mode by keying *99. After keyswitch operation is verified (see below), unplug the AC transformer. KeysWitch Operation To arm AWAY, turn key and release within a 1/2 second. To arm STAY, turn and hold key for longer than 2 seconds. To disarm, turn key and immediately release. LED indications are defined as follows: GREEN RED MEANING OFF OFF DISARMED& NOT READY ON OFF DISARMED& READY OFF ON STEADY ARMEDAWAY OFF SLOWFLASH ARMEDSTAY OFF RAPIDFLASH ALARMMEMORY -51-

General Information An Audio Alarm Verification (AAV) module, such as the Eagle 124~ is an add-on accessory that permits voice dialog between an operator at a central station and a person at the alarm installation, for the purpose of alarm verification. I Mter all messages have been sent during a reporting session to the primary phone number, the control will trigger the AAV if at least one of the messages was an alarm report. If Contact ID format is selected for the primary phone number, the control will send a listen-in to follow message, which signals the 685 to hold the phone connection for 1 minute. Once the digital message is kissed off, the control w-ill give up the phone line to the AAV module, without breaking connection with the central station. At this time, all sirens and all continuous keypad sounds in all partitions will be shut off. W* Connections The method used to trigger AAV is via the use of a 4204 or 4229 relay module, as shown in the AAV comection diagrams that follow (one diagram for connections when a 4285 VIP module is used, the other when the 4285 is not used). w ROgramming 1. 2. 3. 4. 5. 6. With at least one 2-line Alpha keypad (5137AD or 6139) connected to the Partition 1 terminals, power up the system. If you had previously connected the AC transformer to the control panel, you need only plug in the trsmsformer (to 120VAC outlet) to power up the system. Enter the programming mode by keying the following on the Alpha keypad: Installer code (4 1 12)+8 00. Press ml. OPTION SELECTION. Enter 4 for AAV monitoring. O must be entered for UL installations (AAV disabled) Relay programming in field *80: Do not program anything for Relay #1. Exit the programming mode by keying *99. Unplug the AC transformer. I -52-

L, INCCMNQ TELCO LINE.- lerminals ON CONTROL NWTTRIGGER I II I&l REUY1. SNOWN NOTE 00 NOT USE REIAY 1 ~R ANY OTNER WRFQSE. I@ure 18. Connection Of AAV Unit When Not Using A 42S5 VIP Module 1 1. 4 NOTE 00 NOT USE RELAY 1 FOR ANY other PURPOSE. Figure 19. Connection Of AAV Unit When Also Using A 4285 VIP Module -53-

In Section 2, you made temporary power connections for the purpose of ~ programming and testing the keypads. This section provides information about final power-up procedures and battery size calculations. Earth Ground Connections The designated earth ground terminal (25) must be terminated in a good earth ground for the lightning transient protective devices in this product to be effective. It also must be grounded to enable the telephone line fault indicator to work properly. The following are examples of good earth grounds available at most installations: AC power-up Metal Cold Water Pipe: Use a non-corrosive metal strap (copper is recommended) firmly secured to the pipe to which the ground lead is electrically connected and secured. AC Power Outlet Ground Available from 3-prong, 120VAC, power outlets only. To test the integrity of the ground terminal, use a three-wire circuit tester with neon lamp indicators, such as the UL-Listed Ideal Model 61 035, or equivalent, available at most electrical supply stores. 1. Plug the 1321/TF2 or 4300 transformer into a 24-hour, uninterrupted 120VAC outlet. 2. Following power-up, AC, dl (disabled), or Busy-Standby (Alpha keypads) or NOT READY (fixed-word keypads) will be displayed. Also the green POWER LED* on the keypad(s) should light. * Somekeypadsare equippedwitha READY LEDin place of a POWER LED. After approximately 1 minute, the initial displays will revert to DISARMED...READY TO ARM for Alpha keypads, or READY for Fixedword keypads (if there are no faulted zones). This l-minute delay allows PIRs, etc. to stabilize. To bypass this delay, press: [#l + [01. w Connecting The Back-Up Bettery In the event of an AC power loss, the Control panel is supported by a back-up, rechargeable gel cell batte~. The minimum battery size recommended is the No. 467 (12V, 4AH) battery. See Calculating The Battery Size Needed below. The battery is installed in the control cabinet. The standby battery is automatically tested every 4 hours, beginning 4 hours after exiting programming mode. In addition, entry into the test mode will cause a battery test to be initiated. Calculating the Battery Size Needed Determine the total device current draw after filling in the AUXILIARY DEVICE CURRENT DRAW WORKSHEET on the next page. To this figure add the 100 ma that is drawn by the control panel itself. Then, to determine the battery size needed, use the following formula TotalCurrentDrawn*x Numberof hoursstandbywanted= BatteryAmpere/Hours. * ConvertmAfiguretodecimalAmps(seeexample). Example: If total auxiliary device current drawn is 450 ma, add 100 ma for the control panel, for a total of 550 ma (0.55 amps); if 24-hour standby is wanted, the calculation will be: 0.55 ti x 24 hours = 13.2 &npere/hour battery needed. In this example, two 7 Arnp/Hr batteries (comected in parallel) must be used. -54-

Making the BatteryConnections 1. Use the battery standby formula (above) to select the appropriate battery for the installation. 2. Attach the Red and Black wires on the battery connector cable as follows: a) Red to the positive (+) battery tab on the contiol board. b) Black to the negative (-) battery tab on the control board. See the SUMMARY OF CONNECTIONS diagram for location of the (+) and ( ) battery tabs on the control board. 3. Attach the Red and Black wires at the other end of the battery connector cable as follows: a) Red to the positive (+) terminal on the battery. b) Black to the negative (-) terminal on the battery. Note: The battery is periodically tested automatically (approximately every four hours), and if it cannot sustain a load, a low battery message is displayed and, if so programmed, will be reported to the central station. AUXILIARY DEVICE CURRENT DRAW WORKSHEET DEVICE CURRENT # UNITs TOTAL CURRENT 4127 Keypad 20 d 4137AD Keypad 5137AIYADRKeypad 60 ti 90 ma 6127 Keypad 20 ma 6128 Keypad 30 ma 6137 Keypad 85 ma 6138 Keypad 100 ma 6139/6139R Keypad 100 ma 4219 ZoneExpander 35ti 4204 RelayUnit 15/180mA$ 4229 ZoneExpander/RelayUnit 35/loomA$ 4285 VIP Module 160mA * * * * * TOTAL = (CurrentavailablefromAux.terminals=600mAmax.)** * If usinghard-wiredevicessuch as PIRs,refer to the specificationsfor that particularunit scurrent draw. ** In UL installations,maximum current draw ffom the Auxiliary Output and the Alarm Output combined mustnot exceed700 rd (600m!l max fromaux output).. $ Figuresarefor relaysoff/relayson. I -55-

This section provides instructions for programming Alpha descriptors. This is recommended for systems using Alpha keypads, and necessary if a 4285 module is used. If using a 4285 module, select from those words in the Alpha Vocabulary list shown in boldface type. The 4285 module will not provide annunciation of the other words. y 1$ g 4283 module is zidiled @ an exis$$ng,~s~a-26hw system; the;alpha.<,.,#<- des@ipto~s pr+setitl$iii the system shptdd,~re-prcgrammedj seleetingfioti ~,. I tliosewords shown m boldface ty&&iq~eaipba Vocabula@list~ The 4285 : module wiil not provide annunciation iifan~ oihir.words. The ALPHA VOCABULARY on a foilowing page. LIST and CHARACTER CHART will be found Assigning Zone Descriptors The Alpha Keypad used with the VISTA-20HW can have a user-friendly English language descriptiordlocation of all protection zones, keypad ptiics, and RF receiver supervision faults programmed into the system. Each description can be composed of a combination of words (up to a maximum of 3) selected from a vocabulary of 244 words stored in memory (see a following page). In addition, up to 5 installer-defined words can be added to those already in memory. Thus, when an alarm or trouble occurs in a zone, an appropriate description for that zone s location will be displayed at the keypad. Note: Alpha Descriptor entry can be done locally at the Alpha Keypad or remotely using Downloading software. The Alpha keypad procedure is described below. Entering Zone Descriptors (program menu mode *S2) The descriptorcan be enteredwhenthe zone is being definedin field*56 but we recommendthat it be donein field *82. There are two methods that can be used to enter Alpha descriptors. The easiest method requires that you simply enter the 3-digit reference number for the desired word(s). The 3-digit number for each word is provided in the Alpha Vocabulary list (on a following page). An alternate method allows you to pick the desired words by scrolling through the Alpha Vocabulary list. Programming the Descriptors 1. With the system powered up, enter the programming mode by keying Installer code (4 11 2) + 8 + O+ O. The following display will appem b I Installer Code 20 I IProgram Alpha? O= No, l= Yes 00 I ICustom Words? o = No, 1 = Yes 00 I 2. Press *82. The Program Alpha? prompt will appear. 3. Press 1 (Yes). The Custom Words prompt will appear. -56-

When entering Zone ~ Descriptors usin~method z, the keypad keys perform the following function= [3] Scrolls both alphabet and actual words in ascending alphabetical order. [1] Scrolls both alphabet and actual words in descending alphabetical order. [6] Selects between alphabet and actualword list; alsoused to savewords. [8] Stores the zone description in memory. SummuryModeDisplay DefaultDescriptor$ p), ZONEOI,, FlashingCursor(systemis readyforentryof word). +i+znol~ 4 FlashingCursor$ * ZN 01 HACK II +f ZN 01 BACK A t FlashingCursorif 6 is pressed (systemis ready for nextword). ++ ZN 01 BACK El D OOR t FlashingCursor 4. Press O (No).* The system will then automatically display the descriptor for zone 1. * The procedurefor addingcustomwordsto the built-invocabularywill be found later under AddingCustomWords. 8. 5. To delete or change the default descriptor for zone 1, press * plus the same zone number (01). This will clear that descriptor and gain access to the entry mode with flashing cursor, allowing changes to be made. NOTE: If you do not wish to change the existing descriptor. for zone 1, enter * plus the next zone number for which you wish to enter (or check) a descriptor. A summary display for that zone will appear. You must then press * plus the same zone number again to gain access to the entry mode (flashing cursor) for that zone. 6. Press # plus 3-digit number for the first word from the Alpha Vocabulary List. Example: The descriptor that we wish to enter for zone 1 is BACK DOOR. From the list, BACK = 013. Therefore, you would enter# O1 3. Note: If you accidentally enter the wrong word, simply press # plus the correct 3-digit number for the word you want. 7. Press 6 to accept the selected word and continue. Note: If this is the only word you are using for the descriptor, press 8 instead of 6 to save that word in memory, and then go to step 11. Enter the 3-digit number for the next word. In our example, the word is DOOR, whose number is 057. Enter # O 5 7. This display will appear: If a descriptor was not entered previously for zone 1, the default descriptor for zone 1 will be displayed. Note that this a summary mode, and that no entries can be made. Entries can be made only when the display contains a flashing cursor, which signifies the entry mode. -57-

t Flashing Cursor if 6 is pressed (system ready for nextword). +$ZN 01 II DOOR SummaryDisday BACK I 9. 10. Press 6 to accept the selected word. Note: If these are the only words you ~ are using for the descriptor, press 8 instead of 6 to save them in memory. The two words in our example have now been entered. Note, however, that up to three words may be entered (provided the number of characters will fit on the screen). Press 8 to save all words in memory. The A with the flashing cursor over it will disappear, indicating that the word(s) are stored in memory for that zone, as shown in the summary display at the left. I Program Alpha? o = No, 1 = Yes 00 I 11. To enter a descriptor for the next zone, press * plus the desired zone number (e.g., *02. The summary display following step 4 previously will appear. Now repeat steps 6 through 10 for the descriptor for the next zone. 12. To exit the Alpha descriptor mode, press *+O+(J at the summary display. This prompt will be displayed. * I Alpha Pgm - 13. 82 II Press O. This will be displayed. Alternate Method For Programmiog Zone Descriptors 1. Performsteps1 through5 of previous method. 14. Press *99 to exit the programming mode. 2. Note that the first letter of the alphabet appears after the zone number, and that the zone number is automatically included with the description. If there already is a description for the zone, the description will appear (with no cursor, since this is a display mode). To enter or change a description, press [*I+ Zone Number again. A flashing cursor will now appear. Assume, for example, that the desired description for zone 1 is BACK DOOR. 3. Select the first letter of the desired description (note that A is already displayed). Press key [3] repeatedly to advance through the alphabet (e.g., to B ), or key [1] to go backward. Then press [6] to display the first available word beginning with the desired letter (e.g., BABY). Next, press [3] repeatedly to move forward, or [1] to move backward, until the desired word is displayed (e.g., BACK). Then press [61 to accept the word and toggle back to the alphabet list. -58-

4. For selection of the next word (e.g., DOOR), repeat step 3, as follows.. Press key [3] until the first letter of the next word appears (e.g., D ). Then press [6] to display the first available word beginning with that letter (e.g. DAUGHTERS). Press [3] repeatedly until the desired word (e.g., DOOR) appears. To accept the word, press [61,which toggles back to the alphabet list. 5. When all desired words have been entered, press [8] to store the description in memory. 6. Enter *NN, where NN is the next zone that you want to review or for which you want to program a descriptor. To modi~ the descriptor, enter *NN again. To exit this mode, press *00. Adding Custom Words (will not be annunciated by the 42S5 Module) You can add up to five installer-defined words can be added to the built-in vocabulary. Each of the five words can actually consist of a word string of one or more words, but no more than ten characters can be used for each word or word string. [3] [11 [6] [4] [7] [81 Advances through the alphabetin ascending order. Moves through the alphabetin descending order. Selects desired letter; movescursorone space to right. Movescursorone space to left. Inserts a space at the cursorlocation,erasing any character located there. Savesthe new word in thesystem smemory. 1. 2. 3. 4. 5. 6. Perform steps 1, 2, and 3 of Programming the Descriptors on a previous page. Select CUSTOM WORD mode (enter 1 ) when the prompt CUSTOM WORD? is displayed. Enter the number ([1]-[5]) of the custom word or word string to be created (for example, if you are creating the first custom word or wordstring, enter [1], for the second, enter [2], etc.). A cursor will now appear at the beginning of the second line. One of two methods of entering the custom word s characters can now be used (refer to the CHAR4CTER LIST of letters, numbers, and symbols on a following page): Method 1: Press the [#] key, followed by the two-digit entry for the first letter you would like to display (e.g., [6][5] for A ), or... Method 2: Use the [31key to advance through the list of symbols, numbers, and letters. Use the [1] key to move back through the list. When you have reached the desired character, press [6] to select it. The cursor will then move to the right, in position for the next character. Repeat steps 3 and 4 to create the desired word(s). Note that the [41key can be used to move the cursor to the left, if necessary, and that key [71 can be used to enter a blank (or erase an efisting character). Remember, no word or word-string can exceed 10 characters. Press the [8] key to save the custom word(s) and return to the CUSTOM WORD? display. Repeat steps 2-5 for other custom words to be entered. To change a custom word, just overwrite it. If no more are to be entered now, press [01 to return to the Descriptor entry. The custom word(s) will be automatically added to the built-in vocabulary. When zone descriptors are being entered as described in step 6 of Programming the Descriptors, the custom word numbers are 250 to 254 for words 1 to 5 respectively. When being entered as described in step 3 in Alternate Method For Programming Zone Descriptors, each word will be found at the end of the, group of words that begin with the same letter as it does. -59-

000 (WordSpace) A AIR ALARM ALCOVE ALLEY 001 002 003 004 005 006 007 008 009 010 011 AMBUSH AREA APARTMENT ART AITIC AUDIO AUXILIARY 016 BASEMENT 017 BATHROOM 018 BED 019 BEDROOM 020 BELL 021 BLOWER 022 BOILER 023 BOITOM 024 BOX 025 BREAK 026 BUILDING 027 BURNER c 028 CABINET 029 CALL 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 CAM-ERA CAR CASE CASH CCTV CEILING CELLAR CENTRAL CIRCUIT CLIP CLOSED COIN COLD COATROOM COLLECTION COMBUSTION ~~~~~J;R D 048 DAUGHTERS 049 DELAYED 050 DEN 051 DESK 052 DETECTOR 053 DINING Note: 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068. 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 :% 086 087 088 089 090 091 082 093 094 095 096 097 098 099 100 lot 102 103 104 ALPHA VOCABULARY LIST (For Entering Zone Descriptors) DISCRIMINATOR DISPLAY o 105 %TCHEN DOCK m L DOOR DORMER tiundry DOWN LEFT DOWNSTAIRS LEVEL DRAWER LIBRARY DRIVEWAY LIGHT DRUG LINE DUCT E EAST ELECTRIC EMERGENCY ENTRY EQUIPMENT EXECUTIVE EXIT EXTERIOR F FACTORY FAILURE FAMILY FATHERS FENCE FILE FIRE FLOOR FLOW FOIL FOYER FREEZER FRONT FUR FURNACE G GALLERY @&AGE GATE GLASS &&ST H HALL HEAT HIGH HOLDUP HOUSE I INFRARED INSIDE INTERIOR INTRUSION J JEWELRY 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 LIQUOR LIVING LOADING LOCK LOOP LOW LOWER M MACHINE MAGNETIC MAIDS MAIN ~l~ter MEDICAL MEDICINE MICROWAVE MONEY MONITOR ~~;~E{S MOTOR 133 MUD 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 753 154 N NORTH NURSERY 0 OFFICE OIL OPEN :~;g::: OVERFLOW OVERHEAD P PAINTING PANIC PASSIVE PATIO PERIMETER PHONE PHOTO POINT POLICE POOL POWER Q QUAD 155 156 157 158 159 160 161 162 163 E 166 167 168 169 170 171 172 173 174 175 176 177 178 178 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 R RADIO REAR RECREATION REFRIG ~~FRIGERATION,.. RIGHT ROOM ROOF s SAFE SCREEN SENSOR SERVICE SHED SHOCK SHOP SHORT SHOW SIDE SKYLIGHT SLIDING SMOKE SONIC SONS SOUTH SPRINKLER STAMP STATION STEREO STORE STORAGE STORY STRESS STRIKE SUMP SUPERVISED SUPERVISION :W14kl;NG T TAMPER TAPE TELCO TELEPHONE TELLER ~TuE THERMOSTAT TOOL TRANSMllTER TRAP v 209 VALVE 210 VAULT 211 VIBRATION 212 VOLTAGE w WALL WAREHOUSE WASH WEST WINDOW WINE WING 220 WIRELESS 221 WORK 213 214 215 216 217 218 219 x 222 XMl_iTER 223 YARD 224?ONE (No.) 225 ZONE 226 227 z; 230 231 232 233 234 235 236 237 0 i 1ST 2 2ND 3 3RD 4 4TH 5 5TH 238 ~TH 239 7 240 7TH 241 8 242 8TH 243 9 244 9TH 250 Custom Word #1 251 CustomWord #2 252 Custom Word #3 u ULTRA 253 CustomWord#4 I%PER UPSTAIRS UTILITY 254 Custom Word #5 Bulleted (.) words in boldface type are those that are also available for use by the 4285 module. If using a 4285 module, and words other than these are selected for Alpha descriptors, the 4285 will not provide annunciation of those words. CHARACTER (ASCII) CUT (ForAddingCustomWords) 32 (space) 43 + 546 65 A 76 L 87 W 33! 44 55 7 66 B 77 M 88 x 34 45 : 56 8 67 C 78 N 89 f 35 # 46 57 9 68 D 79 0 90 z 36 $ 47 ; 58 : 69 E 80 P 37 % 48 0 59 ; 70 F 81 Q 38 k 49 1 60 < 71 G 82 R 39 50 2 61 = 72 H 83 S 40 ( 51 3 62 > 73 I 64T 41 ) 52 4 63? 74 J 85 U 42 * 53 5 64@ 75 K 86 v w -60-

Report Code Formats This section provides an explanation of formats this system accommodates for reporting alarms and other system conditions to the central station. The process of a successful transmission consists of both the method of communication between the control panel and the central station receiver and the actual way the information is sent and displayed at the central station. When the panel calls the central station receiver, it waits to hear a handshake frequency from the receiver to confirm that the receiver is online and ready to receive its message. Once the panel hears the handshake it is programmed to listen for, it sends its message. The panel then waits for a kissoff frequency from the receiver acknowledging that the message was received and understood. If the handshake frequency is not given or is not understood by the panel, the panel will not send its message. Once the handshake frequency is received and understood by the panel, the panel will send its message. If there is an error in the transmission (the receiver does not receive a valid message), the kissoff frequency will not be given by the central station receiver. The panel will make a total of eight attempts to the primary telephone number and eight attempts to the secondary telephone number (if programmed) to get a valid message through. If the panel is not successful after its numerous attempts, the keypad will display Comm Failure (Alpha keypad) or FC (Fixed-word keypad). The following chart defines the three sets of (handshake/kissoff) frequencies that the panel supports and the different formats that can be sent for each. FORMAT Low Speed 3+1 4+1 4+2 SescoafRad 3+1 4+1 4+2 IHANDSHAKE ITRANSMITSDATA 1400Hz 2300Hz 1900Hz(1OPPS) 1900Hz(20PPS) Express 1400 2300Hz DTMF(10 CPS) 4+2 ContactID 11400 2300Hz IDTMF(10 cps) KISSOFF 1400Hz 2300Hz 1400Hz 1400Hz lttansmittime I Under 15 sees. (Standardreport) Under3 sees. I I -61-

The following describes each format in greater detail. 3+1 and 4+1 Standard Formats 3+1 and 4+1 Expanded Formats 4+2 Format Ademco Contact ID Reporting Format Comprise a 3- (or 4-) digit subscriber number and a single digit report code (e.g. Alarm, Trouble, Restore, Open, Close, etc). Comprise a 3- (or 4-) digit subscriber number, and a two-digit report code. The first digit is displayed on the first line, followed by a second line where the first digit is repeated 3 (or 4) times and followed by the second digit. This is the expanded digit. Comprises a 4-digit subscriber number and 2-digit report code. Comprises a 4-digit subscriber number, l-digit event qualifier ( new or restore ), 3-digit event code, 2-digit Partition No., and 3-digit zone number, user number, or system status number (see the following page). Where: SSS or Ssss = A= z= Tt = Bb = EAC. LLB = 0= 3+114+1 3+1/4+1 Report Standard Expanded 4+2 Alarm SSS(S) A SSS(S)A Ssss M AAA(A) Z Trouble SSS(S)T SSS(S)T TM (T) t Ssss Tt Bypass SSS(S)B SSS(S) B BBB(B)b SSSSBb AC LOSS SSS(S) E SSS(S)E SSSSE& EEE(E)Ac LowBatt SSS(S)L SSS(S) L SSSSLLB LLL(L) LB Open Sss(s) o Sss(s) o Ssss Ou 000(0) u b Close Sss(s) c Sss(s) c Ssss Cu ccc(c) u Test SSS(S) G SSS(S) G SSSS Gg GGG(G)g Restore SSS(S)R SSS(S) R Ssss FtZ Alarm RRR(R) Z AC Restore SSS(S)RA SSS(S)RA SSSSRA~ RARARA(RA)& LoBatRes. SSS(S)RL SSS(S) RL SSSSRLLB RLRLRL(RL)LB TroubleRes. SSS(S)RII SSS(S)RT SSSSRqt RTRTRT7q)t BypassRes. SSS(S)RB SSS(S) RB SSSSRBb RBRBRB(~)b Subscriber ID Alarm Code-1 st digit Typically Zone Number 2nd digit Trouble Code (1st & 2nd digits) Bypass Code (1st & 2nd digits) AC Loss Code (lst & 2nd digits) Low Battery Code(l et & 2nd digits) Open Code-lst Digit Zone numbers foc C = Close Code-1st Digit U = User Number(in hex) Gg = Test Code (Ist & 2nd digits) R = Restore Cede (Alarm) RTt = Restore Code (Trbl)l St & 2nd digits RBb= Restore Code (Byps)l st & 2nd digits RAAC = Restore Code (AC)l st & 2nd digits RLLB = Restore Code (Bat)lst & 2nd digits [x] & [#], or [B] =99 [1]+ [x], or [A] =95 Duress = 92 [3] + [#], or [C] =96 Tamper = 9-62-

Ademco Contact ID Reporting takesthe following format: where: CCCC = Q= CCCC Q EEE GG ZZZ EEE = GG= Zzz = Customer (subscriber) ID Event qualifier, where: E = new event, and R = restore Event code (3 hexadecimal digits) Note: For a complete list of event codes, refer to the central office receiver manual. Partition Number (system messages show 00 ) Zone/contact ID number reporting the alarm, or user number for opeticlose repoi-ts. SyStem status messages (AC Loss, Walk Test, etc.) contain zeroes in the ZZZ location. TABLE OF CONTACT ID EVENT CODES! Code IDefinition I I 110 I Fire Alarm I 121 Duress 122 Alarm, 24-hour Silent 123 Alarm, 24-hour Audible I 131 IAlarm.. Perimeter I 132 Alarm, Interior 134 Alarm, Entry/Exit 135 Alarm. Dav/Ni~ht 143 Alarm, Expansion Module 146 Silent Burglary I 150 IAlarm, 24 Hour Auxiliarv I 301 AC Power 302 Low System Battery/Battery Test Fail I 305 System Reset 333 Trouble or Tamper Expansion Module 351 Telco Line Fault Code IDefinition I 7 353 Long Range Radio Trouble 373 Fire LOODTrouble 374 Exit Error 380 Touble, Zone Trouble 401 Disarming, Armed AWAY(MAX), Armed AWAY(keysWitch) 406 Cancel by User 407 IRemoteArm/Disarm(Dowrdoadimz) I 408 Quick Arm AWAY/MAX 441 Armed STAYflNSTANT,Quick Arm STAYIINSTANT,Armed STAY(Keyswitch), 570 IBypass I 602 [ Periodic Test I 607 System Test 623 Event Log 80% Full 629 l-1/3 Day No Event I

Communication Programming Introduction This sectionprovidesinstructionsfor programmingthosefields that affectcommunications betweenthe controlandthe centralstation. \ Keypad Programming Procedure 1. With at least one Alpha keypad (5137AD or 6139) connected to the system, power up the system. If necessary, refer to the POWERING THE SYSTEM section for the power-up procedure. If you had previously connected the AC transformer to the control panel, you need only plug in the transformer (to 120VAC outlet) to power up the system. 2. Enter the programming mode by keying the following on the Alpha keypad: Installer code (4 1 12)+!3O 0. Press *O PABX ACCESS CODE. I I I I I Enter up to 4 digits if PABX is needed to access an outside line. If fewer than 4 digits are needed to be entered, exit by pressing * and next field number (e.g., 41). To clear entries from field, press *4o*. Fields * 40, * 41, *42: Enter up to the number of I digits shown. Do not fill unused spaces. Enter O-9, #+11 for *< # + 12 for% # + 13 for a pause (2.5 sees) Press *41 Press *42 PRIMARY PHONE No. 11111111111 Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing * and next field number (e.g., 42). To clear entries from field, press * 41*,% SECONDARY PHONE No. 111111.11111 1 Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing * and next field number (e.g., 43). To clear entries from field, press * -42*. w For Fields *43, *44, * 45, and* 46. Entries are provided for 3 or 4 digits for the primary and secondary monitoring location. Enter digits O 9; #+10 = A (O on some receivers); #+11 = B; #+12 =C; #+13 =D; #+14= E;or# +15= F, To clear entries from field, press* 43*, * 44*, * 45*, or* 46*. See blank Programming Form for examples of Account No. entries. Press *43 PRIMARY SUBSCRIBER ACCOUNT. No. (Partition 1) ~ (primary Central StationAccountNumber). Press *44 SECONDARY SUBSCRIBER ACCOUNT. No. (Partition 1) ~ (Secondary Central StationAccountNumber). Press *45 PRIMARY SUBSCRIBER ACCOUNT. No. (Partition 2) ~ (PrirnaryCentral StationAccountNumber). Press *46 SECONDARY SUBSCRIBER ACCOUNT. No. (Partition 2) ~ (Secondary Central StationAccount Number) Press *47 PHONE SYSTEM SELECT Enter 1 digit (default= O) U If Central Station Receiver is not on WATS line: O= Pulse Dial, 1 = Tone Dial. If Central Station Receiver is on WATS line: 2 = Pulse Dial, 3 = Tone Dial. -64-

Press *48 REPORT FORMAT, PRIMARYJSECONDARY Primary Secondary Determines which format is to be used to report to the central station. O= 3+1; 4+1 ADEMCO Lo Speed Standard (this is the default) 1 = 3+1; 4+1 Radionics Standard 2 = 4+2 ADEMCO Lo Speed Standard 3 = 4+2 Radionics Standard 6 = 4+2 ADEMCO Express 7 = ADEMCO Contact ID Reporting 8 = 3+1; 4+1 ADEMCO Lo Speed Expanded 9 = 3+1; 4+1 Radionics Expanded (Enter *as the 4th digit of* 43 through* ing is to be used.) 46, if 3+1 dialer report Note: The maximum number of alarm and alarm restore reports during one armed period is determined by field * 93. Press *49 SPLIT/DUAL REPORTING Enter Oto disable (Backup report only). This is the default. Press *50 TO PRIMARY TO SECONDARY 1= Alarms,Restore, Cancel Others 2= All except Open/Close, Test Open/Close, Test 3= Alarms, Restore, Cancel All 4= All except Open/Close, Test All 5= All All 15-SECOND DIALER DELAY, BURGLARY Enter Ofor no, or 1 for yes. Default is O(no delay). Enter O for UL installations. I Press *51 Press *52 Press *53 PERIODIC TEST REPORT 1 Selectthe desired test report interval. O= none; 1 =24 hours; 2 = weekly; 3 =30 days. Default is O (none). Test Report Code entered in field* 64 is sent. Reports with Partition 1 Subscriber No. TEST REPORT OFFSET This is the time to first report after exiting from programming or downloading. O= 24-houq 1 = 6 hours; 2 = 12 hours; 3 = 18 hours. Default is 2. SESCOA/RADIONICS SELECT n O= Radionics (o-9, B-F reporting) 1 = SESCOA (O-9 only reporting) Select Ofor all other formats. Default is O. -65-

TO PROGRAM SYSTEM STATUS AND RESTORE REPORT CODES (*59-*76,&*89) The following is a set of guidelines to be used for programming report codes, The actual digits that you enter depend upon the particular installation, and should be in agreement with you and the central station office receiving the signals. Use these guidelines to program this entire section. With a 3+1 or 4+1 Standard Format: Enter a code in the first box 1-9, A, B, C, D, E, or F. Enter #+10 for A (this reports a O on some receivers), #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F. An entry of O in the first box will disable a report. An entry of O in the second box will result in automatic advance to thf next field when programming. With an Expanded or 4+2 Formati Enter codes in both boxes (let and 2nd digits) for 1-9, or A-F, as described above. An entry of O in the first box will disable a report. An entry of O in the second box will eliminate the expanded message for that report. With Ademco Contact ID Reporting Enter a digit in the first box to enable the zone to report. Use a difterent digit for each zone until you have used up available digits. If the number of zones exceeds the number of available digits, begin with digit 1 again. This is an enabling code only and is not the actual code sent to the central station office. Entries in the second boxes will be ignored. For system status (non-alarm) codes, enter a 1 in the first box for all the system conditions you want to send to the central station. An entry of O in the first box will disable the report. Press *59 EXIT ERROR REPORT CODE L-1 If O is entered in this field, no special message will be sent, only the regular alarm and alarm restore code for the zone. If a non-zero code is entered, this message will be sent if an alarm occurs within 2 minutes after the end of the Exit time. Refer to Section 17. DATA FIELD DESCRIPTIONS for a % detailed description of this option. Field %59 ent~ note: The 2nd digit is automatically sent as the 2nd digit of the zone alarm report code programmed in * 56, if expanded or 4+2 reporting is selected. Press *6O TROUBLE REPORT CODE m I This will be sent if a zone goes into trouble. Press *61 BYPASS REPORT CODE This will be sent when a zone is manually bypassed. M Press *62 Press *63 Press *64 AC LOSS REPORT CODE n I Reports with Partition 1 Subscriber No. Timing of this report is random with up to a 4-hour delay. If AC restores before the report goes out, there is no AC restore report. LOW BAT REPORT CODE m This will be sent when a low battery condition exists in the system s standby battery. Reports with Partition 1 Subscriber No. TEST REPORT CODE n I This is sent periodically to test that the communicator and phone lines are operational (frequency of report is selected in field *51). Reports with Partition 1 Subscriber No. -66-

Press *65 OPEN REPORT CODE Part n In Part n 2 This is sent upon disarming of the system. 2nd digit. User No., if expanded or 4+2 reporting is selected. See TO PROGRAM SYSTEM STATUS AND RESTORE REPORT CODES explanation on previous page for fields %6-*76, and *89. Press W Press *68 Part n 1 Part n 2 ARM AWAY/STAY REPORT CODE 0 0 A~A~ S!l AY AWAYS 1 A~ This option allows for independent programming of AWAY and STAY reports for each partition. 2nd digit of Report is User No., if expanded or 4+2 reporting is selected. Note: Open reports are not sent in if the system was armed STAY and Stay reports not programmed. CANCEL REPORT CODE /J-l This is sent upon disarming of the system after an alarm condition was reported. Press *69 ~~-~-- u Enter Oif a report is desired for QL@ zone restoral, as it occurs. This is the default. Enter 1 if a report is not desired until all zones have restored. Note l not applicable to Contact ID reporting. Press *7O ALARM RESTORE REPORT CODE, 1st DIGIT u This is sent when the zone that caused an alarm is restored to its non-faulted condition. 2nd digit is automatically sent as the 2nd digit of the zone alarm report code programmed in field *56, if expanded or 4+2 reporting is selected. Press *71 TROUBLE RESTORE REPORT CODE M This is sent when a trouble in a zone is restored. Field *69 applies. Press *72 BYPASS RESTORE REPORT CODE u This is sent when a zone that has been bypassed is un-bypassed. Field *69 applies. Press *73 AC RESTORE REPORT CODE u This is sent when AC power has been restored iifter an AC power outage. Reports with Partition 1 Subscriber No. Press *74 LOW BAT RESTORE REPORT CODE u This is sent when a system low battery condition is restored to normal. Press *76 TEST RESTORE REPORT CODE m I This is sent when the test mode is exited. Reports with Partition 1 Subscriber No. Press *89 EVENT LOG 80% FULL REPORT CODE n I If an Event Logging selection is made in field *90, a message csn be sent to the central station receiver when the log is 80% full. Note: Aside horn the selection made by the installer in field WO, all log control and readout is accomplished via the Downloader. I -67-

Press *9O EVENT LOGGING 1 O= None; 1 = Alarm/Alarm Restore; 2 = Trouble/Trouble Restore; 4 = Bypass/Bypass Restore; 8 = Open/Close. Default is 3. Exampku To select Alarm/Alarm Restore, and Open/Close, enter 9 ~ (1+ 8); to select all, enter #15. Note: System messages are logged when non-zero selections are made. See Fields *89 and *9O in Section 17. DATA FIELD DESCRIPTIONS for a more detailed description of Event Logging. Press W12.PHONE LINE MONITOR ENABLE. 1 O= Not used (default) 1 = Local keypad display only when phone line is faulted. 2 = Local keypad display plus keypad trouble sound when line is faulted. Each partition turns off its own trouble sound. No automatic timeout. 3 = Same as 2 above plus Device No. 2 STARTS. If either partition is NOTE: armed, external sounder activates. External sounder will be turned off Option 3 may be used by normal bell timeout, or by security code plus OFF from either even if a relay unit or partition (itdoes not have to be the one that was armed). Powerline carrier device Device number 2 must either be programmed to be STOPPED in field is not connected to the *8O or STOPPED by entry of sectity code + # + 8 + 2. Partition in Icontrol. *8O should be set to O for STOP. Press *93 NUMBER OF REPORTS IN ARMED PERIOD O limits reports to a total of 10 per code; 1 allows an unlimited number of al~ plus alarm restore-reports. Defaultis O. Enter 1 for UL installations. Press *94 DOWNLOAD PHONE NUMBER I 11111111111 Enter up to 12 digits; O-9, # +11 for w, # + 12 for #, # + 13 for a pause. Do not fill unused spaces. End field by entering *. To clear entries, press *94*. Press *95 RING DETECTION COUNT FOR DOWNLOADING n Refer to the chart below and program this field accordingly. Voice Answering Module Machine Downloading Field *95 ProL L? Yes No No Setfor value otherthan O (1-15). This will enablethe controlpanel to answerthe phonecall. Otherwise,it won tbe possibleto accessthe Module. Yes Yes No Set for a value higher than the number of rings for which the answering machineis set. Example: if machineis setfor 4 rings,use value 5 or higher. This is recommendedso that the Voice Modulecan stillbe accessedif the answering machineis turned off and does not answerthe phonecall. Yes No Yes Setfor value otherthan O (1-15). Yes Yes Yes 15 to bypass answeringmachine. No No No Enter O No Yes No Enter O No No Yes Enter 1 15 No Yes Yes Enter 15 *96 INITIALIZE DOWNLOAD ID AND SUBSCRIBER ACCT. No. FOR DOWNLOADING (No data entry required) This completes the commwzicafion programming. Exit the programming modeby keying*9. Referto Section 19. TESTING THE SYSTEM to check system operation.

General Information Type 00 Zone Not Used Type 01 Entry/Exit Burglary #1 Type 02 Entry/Exit Burglary #2 Perimeter Type 03 Burglary &pe 04 Interior, Follower Type 05 Trouble by Day/ Alarm by Night You must assign a zone type to each zone, which will then define the way in which the system will respond to faults in that zone. Zone types are defined below. Program a zone with this zone type if the zone is not used. This zone type provides exit and entry delays whenever the zone is faulted if the control is armed in the Away or Stay modes. When the panel is armed in the Instant or Maximum modes, no entry delay is provided. Entry delay #1 is programmable, but Exit delay is automatically set as follows: Exit Delay = Entry Delay (that has been programmed) +40 seconds. Exit delay begins whenever the control is armed, regardless of the arming mode selected. This zone type is usually assigned to sensors or contacts on doors through which primary entry and exit will take place. This zone type provides a secondary entry delay whenever the zone is faulted if the panel is armed in the Away and Stay modes. When the panel is armed in the Instant or Maximum modes, no entry delay is provided. Entry and Exit delays #2 are automatically set as follows: Entry delay #2= programmed Entry delay #1 +30 seconds. Exit delay #2 = programmed Entry delay #1 + 40 seconds. Exit delay #2 begins whenever the control is armed, regardless of the arming mode selected. This zone type is usually assigned to. sensors or contacts on doors through which secondary entry and exit will take place, and where more time might be needed to get to and from the keypad (typically used for a garage, loading dock, or basement door). This zone type gives an instant alarm if the zone is faulted when the panel is armed in the Away, Stay, Instant or Maximum modes. This zone type is usually assigned to all sensors or contacts on exterior doors and windows. This zone type gives a delayed alarm (using the programmed Entry/Exit time) if the Entry/Exit zone is faulted first. Otherwise this zone type gives an instant alarm. This zone type is active when the panel is armed in the Away and Maximum modes. This zone type is bypassed automatically when the panel is armed in the Stay or Instant modes. This zone type is usually assigned to a zone covering an area such as a foyer, lobby, or hallway through which one must pass upon entry (After faulting the entry/exit zone to reach the keypad to disarm the system.) Since this zone type is designed to provide an instant alarm if the entry/exit zone is not violated first, it will protect an area in the event an intruder hides on the premises prior to the system being armed, or gains access to the premises through an unprotected area. This zone type will give an instant alarm if faulted when armed in the Away, Stay, Instant or Maximum (night) modes. During the disarmed state (day), the system will provide a latched trouble sounding ffom the keypad (and a central station report, if desired). T his mm type is USUallYassigned to a zone which contains a foil-protected door or window (such as in a store), or to a zone covering a sensitive area such as a stock room, drug supply room, etc. This zone type can also be used on a sensor or contact in an area where immediate notification of an entry is desired. -69-

24-hour Type 06 Silent Alarm Type 07 24-hour Audible Alarm Type 08 24-hour Auxiliary Alarm Type 09 Supervised Fire (With Verification on Zone 1) This zone type sends a report to the Central Station but provides no keypad display or sounding. This zone type is usually assigned to a zone containing an Emergency button. This zone type sends a report to the Central Station, and provides an alarm - sound at the keypad, and an audible external alarm. This zone type is usually assigned to a zone that has an Emergency button. This zone type sends a report to Central Station and provides an alarm sound at the keypad. (No bell output is provided). This zone type is usually assigned to a zone containing a button for use in personal emergencies, or to a zone containing monitoring devices such as water or temperature sensors, etc. This zone type provides a fire alarm on short circuit and a trouble condition on open circuit. The bell output will pulse when this zone type is alarmed. This zone type is always active and cannot be bypassed. This zone type can be assigned to a control panel basic wired zone, any zone in a wired zone expansion module, or wireless zones. When used with zone 1 on the panel, 2-wire smoke detectors can be used. For an explanation of the verification function, refer to the Operation paragraph in Section 5 under Wiring 2-Wire Smoke Detectors To Zone 1. Note: Only hardwired zone 1 can be programmed as a fire zone in UL installations. However, any wireless zone can be used as a fire zone. Type 10 Interior w/delay Type 23 No Alarm Response Type 24 Silent Alarm This zone type gives entry delay #1 (using the programmed entry time), if tripped when the panel is armed in the Away mode. Entry delay begins whenever sensors in this zone are violated, regardless of whether or not an entrylexit delay zone was tripped fwst. ivo entry delay is provided if tripped when the panel is armed in the Maximum mode. Exit delay is present for any arming mode. This zone type is bypassed when the panel is armed in the Stay or Instant modes. This zone type can be used on a zone when an output relay action is desired, but with no accompanying alarm (e.g., lobby door access). This zone type provides an instant alarm, with NO audible indication at any keypad or external sounder, if the zone is faulted when the system is armed in the AWAY, STAY, INSTANT, or MAXIMUM modes. This zone type is usually assigned to all sensors or contacts on exterior doors and windows where audible notification is NOT desired. A report is sent to the Central Station. w -70-

Descriptions of System Data Fields THE BLANK PROGRAMMINGFORMSHOULDBE USEDTO RECORDTHE DATAFOR THIS INSTALLATION Defaults (where applicable) Are Indicated In Text The following is a table containing a list of all data fields in this control (presented in numerical order). If you have performed the programming instructions that were included with the installation of each of the various peripheral devices covered in previous sections, this table will simply serve as a reference for all data fields in the system. If you have decided to program all the data fields in the system at one time (and therefore did not perform the programming indicated previously in each section), you can use this table to program all the data fields now. *2O *21 *23 *25 *27 *X3 INSTALLER CODE The Installer code is used to enter the 4digit ljjj_l Master security code for each partition in the normal operation mode, via the keypad connected to Partition 1. See Master Code in Section 20. SYSTEM OPERATION for procedure. Enter 4 digits, O-9. Default is 4-1-1-2, QUICK ARM ENABLE Partition1 Partition2 If enabled, the [#] key can be used instead of the security code when arming the system. Enter Ofor disabled or 1 for enabled for each partition. Default is O. FORCED BYPASS FUNCTION Partition1 Partition2 This feature allows sll faulted zones to be bypassed automatically. All zones that are bypassed by this fimction will be displayed after the bypass is initiated. Enter, for each partition: O= No forced bypass. This is the default. 1 = Allows automatic bypass of all open zones. Must be O for UL installations. WIRED ZONE EXPANSION u Use this field to select the type of expansion unit being used, as follows O= none; 1 = 4219; 2 = 4229; 3 = 4204. Default is O. POWERLINE CARRIER DEVICE (X-1O) HOUSE ID Powerline Carrier devices require a House ID. This field identifies this house ID to the control. If Powerline Carrier devices are used, they are selected in field * 80. House ID is entered in following manner: 0= A,1=B,2=C, 3= D,4=E,5=F, 6= G,7=H,8=I,9=J, #+10= ~#+ll=l, #+12= M,#+ 13= N,#+14=0, #+15=P. Default is O. VOICE MODULE PHONE CODE (4285) m The use of a 4285 VIP Module (can be used in Partition 1 only) requires a 2-digit code. Enter a 2-digit phone access code as follows: For first digit, enter any any digit from 1 to 9; for second digit, enter # +11 for *, or # +12 for #. Exomple: If desired access code is 7*, 7 is the first entry, and # + 11 (for *) is the second entry. Default is 00 (Voice Module disabled). Note: A O in either digit will disable the Voice Module. -71- I I

II *29 OUTPUT TO LONG RANGE RADIO u If output to LRR is selected here, all messages that are programmed to go to the primary telephone line receiver will also be sent to the 7720 PLUS or 7820 radio. These messages will always be in Contact ~ ID format (not affected by entry in field *48). The data line is supervised as well as certain functions in the radio. If communication is lost or a trouble develops, a message will be attempted to be sent via both radio and telephone to the central station. Note: Normal trouble restore report (*71) is sent on restore of the condition. Entry is first digit of Trouble Dialer Report; enter Trouble code 1 9, B (# +11), C (# +12), D (# +13), E (# +14), or F (# +15). The 2nd digit of Trouble Dialer Report is automatically the 2nd digit from field %0. For UL installations, Long Range Radio must be disabled (enter O ). I Note: The Radio should be programmed for device address 3 on the - keypad lines. *30 Notes ZONE SOUNDS AND *32 (*3; Note: Entry Delay must be set for a I I Imaximum of 20 seconds I I Iin ULinstallations. *33 *34 *35 KEYSWITCH ENABLE This field must be enabled (enter 1) if using a keyswitch. The keyswitch must be connected to zone 7, which can then not be used for any other purpose. Default is O(no keyswitch). If keyswitch is enabled, in menu mode *56 the Zone Type (ZT) for zone 7 will show 77, and the zone will not be accessible for programming. If the 4146 keyswitch is used with only Red and Green LEDs comected (no lock switch and tamper switch) to simply provide an arming/ready status indicator panel, zone 7 can then be used as a hard-wired protection zone, provided you do not enable this field. SINGLE ALARM SOUNDING PER ZONE (per armed period) This field limits alarm sounding to once per arming period for a given zone. Enter 1 for yes; default is O(no). FIRE SOUNDER TIMEOUT This field determines whether the external sounder will shut off after time allotted, or continue until manually turned off. Enter O for sounder timeout, or 1 for no timeout. Default is O. This control complies with NFPA requirements for temporal puke sounding of fire notification appliances. Temporal pulse sounding for a fire alarm consists of the following 3 pulses - pause -3 pulses - pause -3 pulses... ALARM BELL TIMEOUT This field determines whether the extermll sounder will shut off after time allotted, or continue until manually turned off. Enter as follows O= No timeout 1 = 4 min (default); 2 = 8 rein; 3 = 12 min. Alarm bell timeout must be set for a minimum of 4 rnin ( 1 ) for UL installations. ZONE TYPE 01 ENTRY DELAY Partition1 Partition2 System will wait the time allotted before sounding alarm upon entering. May be selected individually for each Partition. o = O seconds 2 = 30 seconds 4 = 60 seconds 1 =20 seconds 3 = 45 seconds 5 =90 seconds Default is 2 (30 seconds). Zone Type 02 Entry Delay= Zone Type 01 Entry Delay+ 30 seconds. (EmT delays= Zone type 01 Entry delay plus 40 seconds). -72- %!

DIALER PROGRAMMING (--50) Fields *40, WI, W: Enter up to the number of digits shown. Do not fill unused spaces. Enter O-9, # + 11 for * # + 12 for # # + 13 for a pause (2.5 sees) *36 *37 *38 *4O *41 *44 *45 AUDIBLE EXtT WARNING Partition1 Partition2 If enabled, this field provides exit warning sound when armed AWAY it can be selected for either or both Partitions. Warning sound consists of slow continuous beeps until last 5 seconds, when it changes to fast beeps. The warning sound will end at the termination of Exit time. O= no; 1 = yes. Default is 1. CONFIRMATION OF ARMING DING Part n1 Part>n2 Enter 1 (in either or both Partitions) to enable 1/2 second external alarm sounding ding when closing report goes in, or at the end of exit delay. Odisables the ding (default). POWER UP IN PREVIOUS STATE 1 Enter 1 for Yes (default) if, upon power-up, you want the system to assume the system status prior to power down. Enter Oif you want the system to always power up in a disarmed state. When the system powers up armed, an alarm will occur 1 minute after arming if a zone is faulted. Must be 1 for UL applications. Note that if the previous state was armed AWAY or STAY, the system will not respond to sensor changes for 1 minute, which allows time for sensors such as PIRs to stabilize. PABX ACCESS CODE (See Box at Left) ~ Enter up to 4 digits if PABX is needed to access an outside line. If fewer than 4 digits are needed to be entered, exit by pressing * and next field number (e.g., 41). To clear entries horn field, press =0*. PRIMARY PHONE No. (See Box at Left) 11111111111 Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing * and next field number (e.g., 42). To clear entries fkom field, press *41*. Note: Back-up reporting (8 calls are made to the secondary phone number if no kiss-off is received after 8 attempts to the primary number) is automatic only if there is a secondary phone number (field *42). SECONDARY PHONE No. (See Box at Left) 11111111111 Enter up to 12 digits. If fewer than 12 digits entered, exit by pressing * and next field number (e.g., 43). To clear entries from field, press *42*. See Note in field *41 above, also. Notes For Fields W, W, W, and *6. Entries providedfor up to 4 digitsfor primary office and 4 digits for secondary. Enter digits O-9; # +ll=b; # +12=C; # +13=D; # +14=E; or # +15=F. Enter *as the fourth digit if a 3-digit account number (for 3+1 dialer reporting format) is used. Enter Oas the first digit of a 4-digit account number for Nos. 0000-0999. Exit field by pressing * (and press next field number) if only 3 digits are used. To clear entries from field, press *3*, W*, *45* or *46*. See blank Programming Form for examples of Account No. entries. PRIMARY SUBSCRIBER ACCOUNT. No. (partition1) ~ Primary Receiver. See notes above. SECONDARY SUBS ACCOUNT. No. (partition 1) ~ Secondary Receiver. See notes above. PRIMARY SUBSCRIBER ACCOUNT.. No. (Partition 2) Ill I Primary Receiver. See notes above. -73-

..,. -4ti *47 *48 SECONDARY SUBS ACCOUNT. No. (Partition. 2) 1~/ SecondW Receiver. See notes previously. PHONE SYSTEM SELECT Default is O. 1 m Enter 1 digit. If Central Station Receiver is not on WATS line: O= Pulse Dial, 1 = Tone Dial. If Central Station Receiver is on WATS line: 2 = Pulse Dial, 3 = Tone Dial REPORT FORMAT Primary Secondary Determine which format is to be used to report to the central station. Enter 1 digit (O-9). O= 3+1; 4+1 ADEMCO Lo Speed Standard (this is the default) 1 = 3+1; 4+1 Radionics Standard 2. 4+2 ADEMCO Lo Speed Standard 3 = 4+2 Radionics Standard 6. 4+2 ADEMCO Express 7 = ADEMCO Contact ID Reporting 8 = 3+1; 4+1 ADEMCO Lo Speed Expanded 9 = 3+1; 4+1 Radionics Expanded (Enter *as the 4th digit of X3 through *46, if 3+1 dialer reporting is to be used.) For an explanation of these formats, see Section 15. SYSTEM COMMUNICATION. IVote: The maximum number of alarm and alarm restore reports during one armed period is determined by field *93. -9 SPLIT/DUAL REPORTING Enter Oto disable (Backup report only). This is the default. TO PRIMARY TO SECONDARY 1= Alarms,Restore,Cancel Others 2= All exceptopen/close,test Open/Close,Test 3= Alarms, Restore,Cancel Ml 4= All exceptopen/close,test All 5= All All u w *5O *51 *52 *53 15-SECOND DIALER DELAY (BURGLARY) u If selected, will provide 15-second delay of burglary alarm report to the central station. Allows time for subscriber to avoid a false alarm transmission. Enter Ofor no or 1 for yes. Default is O(no delay). Must be O for UL installations. PERIODIC TEST REPORT 1 Select the desired test report interval. O= none; 1 = 24 hours; 2 = weekly; 3 = 30 days. Default is O (none). Test Report Code entered in field *64 is sent. Reports with Partition 1 Subscriber No. TEST REPORT OFFSET n This is the time to first report from programming or downloading. O=24 hours; 1 = 6 hours; 2 = 12 hours; 3 = 18 hours. Default is 2. SESCOA/RADIONICS SELECT O= Radionics (O-9, B-F reporting) 1 = SESCOA (O-9 only reporting) Select Ofor all other formats. Default is O. I -74-

ml Zone 17 enteredt ZnZTPRC In: L 17 091 10 AW:- J Zone Number m *56 ZONE ASSIGNMENT/ALARM REPORT CODES REFER TO THE ZONE ASSIGNMENT T)4.BLE FOR *56 IN THE CENTERFOLD PROGRAMMING FORM. This is an interactive menu mode that is used to program zone numbers, zone types, partition numbers, alarm and report codes, and to identify the type of loop input device. This mode can also be used for entering Alpha descriptors for zones (we recommend entering descriptors in menu mode *82. Upon entry menu mode *56, the following is displayed: Zone Number (Zn): Enter the zone number that you wish to program (or [0][0] to leave zone programming). Press [*]. A summary display will come up, showing the status of that zone s program. If it is programmed satisfactorily, press [#] to back up one step and enter another zone number, if desired. If the zone is not programmed, or you want to change it, press [*]. A prompt for Zone Type will appear. Zone Type (ZT): Each zone must be assigned to a zone type, which defines the way in which the system responds to faults in that zone. Enter the zone type code (or change it, if necessary). Zone types are listedbelow 00= NotUsed 06= 24 Hr Silent 10. Interiorw/Delay 01 = Entry/Exit#1 07= 24 Hr Audible 23. No Alarm 02= Entry/.Exit#2 08=24 HrAux Response 03 = Perimeter 09= FireW/venf. 24= SilentBurglary 04= interiorfollower 05= TroubleDay/AlarmNight Default values for zones 01 to 08 are: Zone No.(Zn): 01 02 03 04 05 06 07 08 Zone Type Default 09 01 03 03 03 03 03 03 Partition Default 1 1 1 1 1 1 1 1 Response Time Default * 1 1 1 1 1 1 1 1 x ulflfor response time = 350 msec. When the display shows the zone type you want, press [*I to advance to... I 17 Partition 1 I Partition No. (P) (Default = [1]. Enter 1 or 2. Press [*] to advance to... Report Code (RC): The report code consists of 2 hexadecimal digits, each in turn consisting of 2 numerical digits. For example, for a report code of 3C, enter [0][3] for 3 and [1][2] for C. Enter the numbers and press [*] to advance to... Input Device (In): For the hardwired zones of the VISZ A-20HW (HW), the auxiliary wired expansion zones on a 4219 or 4229 (AW), the Input Device types are automatically displayed (Panic, Duress, and Tamper inputs are not applicable). When all is okay, press [*] to advance to... -75-

Custom Alpha Editing: For all zone types, the next request is to enter Alpha descriptors for the zones. The entry may be done now (enter 1), or maybe done at a later time via *82 mode (enter O). See Section 14. ALPHA DESCRIPTION PROGRAMMING for w procedure. Enter Zn Num. (00 = Quit) 00 17 Zone Type II Not used 00 I 17 Delete Zone? II 1I= Yes O=NO II When all entries to be made for the zone at this time are complete, the next zone number can be entered for programming, or zone programming can be ended by entering [0][0] as the next zone number. Notes: 1. In jleld *56, at the summary line for each zone, the entered values can be checked. If it is desired to change anything, press [#] to move to the previous entry. Press [#] a number of times to move to earlier entries. Press [*I to move to later entries again. 2. Zone entries can be reviewed by pressing [#][5][6]. Changes cannot be made here, so this is safer for review. Enter the first zone number to be viewed and press [#l. To view each zone, press [#] and the zone number will advance to the next programmed zone. When the end of the list is reached, press [01[0] to exit. This method of exiting may also be done at any time during the review. 3. To either temporarily or permanently remove a zone from the system, go into programming mode and press [*][5][6]. Enter the zone number and press [*I. At the Zone Type prompt, enter [01[01 and [*I. This sets the type of the zone to Not Used. The next prompt will be Delete Zone?. Yes will permanently remove the zone from the system, while No will disable it but retain all data except the ori~nal zone type. You can then go back to this zone later and put back an active Zone Type to re-enable it. TO PROGRAM SYSTEM STATUS AND RESTORE REPORT CODES (*59 - *76, & #419) The following is a set of guidelines to be used for programming report codes. The actual digits that you enter depend upon the particular installation, and should be in agreement with you and the central station office receiving the signals. Use these guidelines to program this entire section. With a 3+1 or 4+1 Standard Format: Enter a code in the first box: 1-9, A, B, C, D, E, or F. Enter #+10 for A (this reports a O on some receivers), #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F. An entry of O in the first box will disable a report. An entry of O in the second box will result in automatic advance to the next field when programming. With an Expanded or 4+2 Formati Enter codesin both boxes (lst and 2nd digits) for 1-9, or A-F, as described above. An entry of O in the first box will disable a report. k entry of O in the second box will eliminate the expanded message for that report. With Ademco Contact ID Reporting Enter a digit in the first box to enable the zone to report. Use a different digit for each zone until you have used up available digits. If the number of zones exceeds the number of available digits, begin with digit 1 again. This is an enabling code only and is not the actual code sent to the central station office. Entries in the second boxes will be ignored. For system status (non-alarm) codes, enter a 1 in the first box for all the system conditions you want to send to the central station. An entry of O in the first box will disable the report. -76-

SYSTEM STATUS *59 REPORT CODES (*59-W3) *60 *61 *62 *63 *64 *65 *66 *67 *@ EXIT ERROR REPORT CODE (Seebox previously) 1 If the systemis armedand an Entry/Exitor Interiorzoneis still open after the exit delay time has expired, an alarm will sound at the keypadand external sounder(keypadalso displays Exit Alarm ). If the system is disarmed before the end of the entry delay that immediatelyfollows,the alarm soundingwill stop and no message wiil be sent to the central station. The keypad will display CA (fied-word keypads)or CANCELEDALARM (Alphakeypads). If the system is not disarmed before the end of the entry delay mentionedabove,and an Entry/Exitor Interiorzone is still open, an exit alarm message will be sent to the central station if an Exit Error Report code is selected in this field. The keypadwill display EA (fixed-wordkeypads)or EXIT ALARM (Alpha keypads), and the zdarmsoundingwillcontinueuntil the system is disarmed(or timeoutoccurs). An ExitAlarm conditionwillalsoresultif a fault occursin an exit or interiorzone within2 minutesfollowingthe end of the exit delay, and an exitalarm messagewillbe sentto the centralstation. If ContactID formathas been programmed,the message will contain the zonenumbersnd errorcode374 (Troubl*Exit Error)to definethe alarm as an Exit Error(ratherthan E/E or Interior).If 4+2 format is used, the digitenteredin this fieldwill be sentfollowedby the second digitof the programmedalarmcodeforthat zone. If 3+1 or 4+1 format is used, only the digitenteredin this field will be sent. This message will go to the PrimaryPhone No. Under any of these conditions,no Restoremessagewillbe sent. If O is enteredin this field,no specialmessage will be sent, only the regularalarmand alarmrestorecodefor the zone. TROUBLE REPORT CODE (Seebox previously) BYPASS REPORT CODE (Seeboxpreviously) AC LOSS REPORT CODE m See box on previouspage. Reportswith Partition 1 SubscriberNo. Timing of this reportis randomwith up to a 4-hour delay. If AC restoresbeforethe reportgoesout,thereis no AC restorereport. LOW BAT REPORT CODE See box. ReportswithPartition1 SubscriberNo. TEST REPORT CODE Seebox. Periodic Reports with Partition 1 Subscriber No. OPEN REPORT CODE See box on previous page. 2nd digit = reporting is selected. ARM AWAY/STAY REPORT CODE m m m 1 User #, if expanded or 4+2 m r-i---l This option allows for independent programming of AWAY and~y reports for each partition. 2nd digit of report is User No. if expanded or 4+2 reporting is selected. RF XMTR LOW BAT REPORT CODE. (NOT USED) CANCEL REPORT CODE (Seebox on previouspage.) m -77-

RESTORE *69 REPORTCODES (*6=76) *7O *71 *72 *73 *74 *75 *76 *8O *81 *8,2 GROUP RESTORES FOR TROUBLE, BYPASS EnterO for no (report for ~ restore), or 1 for yes (report after M zones restored). Default is O. Note: 1 not applicable to Contact ID reporting. ALARM RESTORE REPORT CODE, 1st DIGIT 1 2nd digit is automatically sent as the 2nd digit of the zone alarm report code programmed in field *56, if expanded or 4+2 reporting is selected. TROUBLE RESTORE REPORT CODE m See box on previous page. This is sent when a trouble in a zone is restored. Field *69 applies. BYPASS RESTORE REPORT CODE m See box on previous page. This is sent when a zone that has been bypassed is un-bypassed. Field *69 applies. AC RESTORE REPORT CODE m Seeboxon previouspage. Reports with Partition 1 Subscriber No. LOW BAT RESTORE REPORT CODE m Seeboxon previouspage. Reports with Partition 1 Subscriber No. RF XMTR LOW BAT RESTORE REPORT CODE. (NOT USED) TEST RESTORE REPORT CODE m See box on previouspage. Reports with Partition 1 Subscriber No. A restore code entered here will cause a restore message to be sent when Test mode is exited. OUTPUT DEVICES This is an interactive menu mode that is applicable only if field *25 is programmed for a 4229 or 4204, or if Powerline Carrier devices are to be used. See Section 7. REL4Y OUTPUTS & POWERLINE CARRIER DEVICES for a detailed programming procedure. Also refer to the OUTPUT DEVICE table for *8O in the Programming Form. ZONE LISTS FOR OUTPUT DEVICES This is an interactive menu mode that is applicable only if field *25 is programmed for a 4229, 4204, or if Powerline Carrier devices are used. Refer to Section 7. RELAY OUTPUTS & POWERLINE CARRIER DEVICES for a detailed programming procedure. Also refer to the ZONE LISTS FOR OUTPUT DEVICES table for *81 in the Programming Form. CUSTOM ALPHA EDITING See Section 14. ALPHA DESCRIPTION PROGRAMMING for procedure. DDDELETE RF INPUT IDs. (NOT USED) EVENT LOG 80% FULL REPORT CODE m (Also see To PROCRAM SYSTEM STATUS, & RESTORE REPORT CODES box on a previous page). If an Event Logging selection is made in field *90, a message can be sent to the central station receiver when the log is 80% full. If the log becomes fill, a new message will overwrite the oldest message in the log. Note: Aside from the selection made by the installer in field *90, all control and readout from the log is accomplished via the Downloader (see field *90). -76- ~, w

*W EVENT LOGGING The VISTA-20HW system has the ability to record various events in a history log (48-event capacity). The types of events to be logged can be selected as indicated below. At any time, the downloader operator can then upload the log and view or print out all or selected categories of the log. The log can also be cleared by the downloader operator. The display/printout at the central station will show the date, time, event, and description of the occurrences. The time is calculated by an internal clock at the central station computer. Note that the time for any events that occur prior to a system power-down or an entry into the programming mode cannot be calculated by the central station computer. The time will then appear on the log as unknown. O= None; 1 = Alarm/Alarm Restore; 2 = l?roublal rouble Restore; 4 = Bypass/Bypass Restore; 8 = Open/Close. The default is 3. Example: To select Alarm/Alarm Restore, and Open/Close, enter 9(1 + 8); to select all, enter #15. Note: System messages are logged when any non-zero selection is made. *9 I OPTION SELECTION Enter 4 if an Audio Alarm Verification (AAV) unit is connected in the system (l-3 not used); enter O if an AAV unit is not being used. For UL installations, o ). the AAV option must be disabled (enter *92 PHONE LINE MONITOR ENABLE u O= Not used(default) 1 = Localkeypaddisplayonlywhenphoneline is faulted. 2 = Localkeypaddisplaypluskeypadtroublesoundwhenline is faulted. Eachpartitionturns offits owntroublesound.no automatictimeout. 3 = Same as 2 above plus DeviceNo. 2 STARTS. If eitherpartitionis armed,externalsounderactivates.external sounderwillbe turned offby normalbell timeout,or by securitycodeplus OFF from either partition (it does not have to be the one that was armed). Device number 2 must either be programmed to be STOPPED in field *8O or STOPPED by entry of security code + # + 8 + 2. Ptiition in *8O should be set to O for STOP. NOTE: Option 3 may be used even if a relay unit or Powerline carrier device is not connected to the control. *93 ~ER C)I?REPORTS IN ARMED PERIOD u This option can be used to limit the number of messages (alarm& alarm restore reports) sent to the central station in an armed period. O limits reports to a total of 10; 1 allows an unlimited number of reports. Default is O. DOWNLOAD *W DO~OAD PHONE NUMBER INFORMATION Enterup to 12 digits; 11111111111 (*9.4, *95) 0-9. # +11 for *. # + 12 for #, # + 13 for a pause. Do not fill unused spaces. End field by entering*. Toclear entri~s from field, press *9LM. *95 RING DETEC~OIN COUNT FOR DOWNLOADING u Enternumberof rings beforecontrolpicksup phoneline(or Oor 15). Referto the chartthat followsand programthis field accordingly. I I -79-

4285 Answering Module Machine Downloading Field *95 Yes No No Set for value other than O (1 15). This will enable the control panel to answer the phone call. Otherwise, it will not be possible to access the 4285 module Yes Yes No Set for a value higher than the number of of rings for which the answering machine is set. Example: if machine is set for 4 rings, use a value of 5 or higher. This is recommended so that the 4285 module can still be accessed if the answering machine is turned off and does not answer the phone call. Yes No Yes Set for value other than O (1 15). Yes Yes Yes Enter 15 to bypass answering machine. No No No Enter O. No Yes No Enter O. No No Yes Enter 1 15. No Yes Yes Enter 15. *96 INITIALIZE DOWNLOAD ID AND SUBSCRIBER ACCT. No. FOR DOWNLOADING (No data entry required, press *96) *97 SET ALL PROGRAM FIELDS TO DEFAULT VALUES (No data entry required, pressing *97 automatically loads all defaults). TO EXIT *9g EXITS PROGRAMMI NG MODE andpreuents re-entry by : PROGRAMMING MODE Installer Code + 8 + O+ O (*98 or *99) *99 EXITS PROGRAMMING G MODE and allows re-entry by: Installer Code + 8 + O+ Oor by Power-up then * and #. -60-

General Information The VISTA-20HW can be remotely programmed horn an IBM compatible Personal Computer (PC), a HAYES Modem, and Ademco s V-LINK@ Soflnvare (as specified below). Equipment Programming the control from a remote location is protected against compromise by someone attempting to defeat the system, using multi-levels of security protection 1. Security Code Handshake: An 8-digit download ID code must be matched between the control and the dowriloader. 2. 3. 4. Site Initiated Remote Programming The installer or subscriber initiates the callback from the subscriber premises (by entering Installer code + # + 1) while disarmed. All parameters can then be downloaded via the phone lines using a personal computer. Station Initiated Remote Programming The operator calls the site from your office to initiate the download call. The control hangs up and then calls back the PC via the preprogrammed telephone number. The unit can then be uploaded, downloaded, or controlled horn your office. Data Encrsmtion: Data Dassed between the PC and the control is encryptedfor ~~curity so tha~ it is very difkult for a foreign device tapped into the phone line to take over communication and substitute system compromising information. Required At the premises:. VISTA-20H Wandkeypad. At the installer s office/home:. An IBM PC compatiblecomputer.. Either a HAYES brandsmartmodem 1200 [Level1.2 or higherexternal or Level 1.1 or higher (with 4 positiondip switch)internal style],or a HAYES brandoptima24 Plus FAX96 Modem.. V-LINK@ DownloadingSoftwareDiskette(atrevisionlevelsupportingthe VISTA-20HW).. Appropriateinterconnectingcables. Initial Download Enter Installer code + # + 5. This setsfieldx95 to 4 rings,subscriberno. to default,and systemto nocall-back option.the downloadcomputercanthen call the subscriber,makeconnection,and downloadall programmingitems. Remote Programming Information The downloadingsystemcan performmanyfunctionswhenin communication with the controlunit. Besidesuploadingand downloading,the status of the system canbe observedand variouscommandscanbe initiated,as follows:. Arm the Systemin the Away Mode;Disarmthe System.. Bypass a Zone.. Forcethe Systemto Accepta New ProgramDownload.. Shut DownCommunication(dialer)Functions(non-paymentof monitoring fees in an owned system).. Shut Down all Security system). System Functions (non-payment for a leased. Inhibit Local Keypad Programming (prevents account takeover). -81-

Command the System to Upload a Copy of its Resident Program to the office.. Read: Arming Status, AC Power Status, Lists of Faulted Zones, Bypassed Zones, Zones Currently in Alarm, Zones Currently in Trouble. Notes: After the control and the PC have established valid communication, each keypad on the system will become inactive and will display CC or MODEM COMM.. The control, however, will still be scanning its zones and looking for alarms. If an alarm does occur, after communication is broken off alarms are sounded and the proper dialer reports are sent to the central station. The keypads will become active afler the download communication is terminated. The detailed operation of the download functions is covered in the installation instructions for the V-LINK@ Downloading Software Diskette. w Remote Progr amming Advisory Notes Alarm and trouble reporting may be delayed during the time that the system and the Downloader are linked to each other following a valid exchange of codes, but the proper message will get through to the Central Station after the link is broken.. Keypad entries are ignored during the time interval stated above.. A copy of the program downloaded may be produced from the IBM PC compatible computer, using the product s internal report generator, when an optional printer is connected (consult your PC manual for proper printer and connections).. Program Upload or Download Time Approximately one minute fifteen seconds for a complete program. -82-

Test Procedure After installation is completed, each partition of the Security System should be carefully tested, as follows. 1. With the System in the disarmed state, check that all zones are intact. If a NOT READY message is displayed, press the [*I key to display the faulted zone(s). Restore faulted zone(s) if necessary, so that READY message is displayed. Fault and restore every sensor individually to assure that it is being monitored by the system. 2. Enter the security code and press the TEST key. The outside sounder will sound for 1 second. The keypad should sound 3 beeps each time a contact is faulted. A test report should be sent (if programmed) to the Central Station immediately. If the backup battery is discharged or missing, the sounder may not turn on and a LOW BATTERY report will be transmitted with a TEST report. The keypad will beep once per minute as a reminder that the system is in the Test Mode. To turn off the test mode enter security code and press the OFF key. Alarm messages will be sent to the central station during the following tests 3 and 4. Notify them in advance that tests will be in progress. 3. Arm the systemand fault one or morezones. After 15 seconds(if optionaldialer delay is selected),silence alarm sounder(s)by entering the code and pressingoff. CheckEntry/Exitdelayzones. 4. Check the keypad-initiatedalarms that are in the system by pressingthe Panickey (key pairson some keypads). If the systemhas been programmed for audible emergency, the keypad will emit a steady alarm sound, and ALARM and zone number willbe displayed.silencethe alarm by entering the security code and pressingoff. If the systemhas been programmedfor silent emergency,there will be no audiblealarmsor displays,but a reportwillbe sentto the centralstation. 5. If output Relay Units/PowerlineCarrier Devices have been installed,test their programmedaction. 6 Noti~ the centralstationwhen all tests are finished,and verifyresultswith them. NOTE: THE TEST MODE WILL BE AUTOMATICALLY TERMINATED AFTER 4 HOURS IF THE INSTALLER OR USER DOES NOT MANUALLY TERMINATE IT. THIS INSURES THAT FIRE AND PANIC ZONES WILL NOT REMAIN DISABLED. TO THE INSTALLER Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are vital to continuous satisfactory operation of any alarm system. The installer should assume the responsibility of developing and offering a regular maintenance program to the user as well as acquainting the user with the proper operation and limitations of the alarm system and its component parts. Recommendations must be included for a specii% program of frequent testing (at least weekly) to insure the system s proper operation at all times.

Security Codes Installer Code The installer programs the 4-digit Installer Code initially as part of the programming procedure. The factory default Installer code is 4-l-l-2, but may be changed in field *20. Master Code The Installer code is the only code that can enter programming mode and also, in normal operation mode, is used to enter the Master code for each partition, which allows access to the normal fimctions of the system. See Section 4. MECHANIC S OF PROGRAMMING for information on exiting the programming mode via fields *98 or *99. In normal operation mode, the Installer code is used to enter the 4-digit Master security code for each partition, using the keypad connected to Partition 1: To enter the Master code for Partition 1, enter: Installer Code + [8] + [01] + desired 4-digit Master code for Partition 1 w To enter the Master code for Partition 2, enter: 1 Installer Code + [8] + [02] + desired 4-digit Master code for Partition 2 Secondary User Codes In normal operation mode, each partition smaster securitycode can be used to assign up to 14 secondary 4-digit security codes for that partition. It can also be used to remove secondary codes from the system (individually). To assign (or change) a Secondaqy security code, enter (via partition s, keypad): Partition s Master Code + [CODE key]+ User # (03-16) + desired Secondary Code I The system will emit a single beep when each secondary code has been successfully entered. To delete a Secondary security code, enter (via partition s keypad): Partition s Master Code + [CODE key]+ User # (03-16) Notes: All Master and Secondary security codes permit access to the system for arming, disarming, etc, The installer code can disarm the system only ifit was used to arm it. User code No. 15 is a babysitter code, i.e., it can disarm the system only if it was used to arm it. User code No. 16 is the Duress code. When this is used to perform any system operation, a special code is sent to the monitoring station. Instruct users to be carefi-dnot to use this code for normal usage, If a secondary code is inadvertently repeated for different users, the lower user number will take priority. Opening and closing reports are sent for the Installer code as No. 01, with the appropriate subscriber number. Each Master code and set of secondary user codes are sent as Nos. 02, and 03 16 respectively in Contact ID format (with the appropriate subscriber number); in 4+2, it is l F, F for anything greater than 15; keyswitch will report as user O. -84-

General Information Arming Functions Notethat if you enabled QUICK ARM for the partition (field *21), the [#] key can be pressed instead of entering the partition s security code, for any of the arming procedures (Away, Stay, Instant, Maximum, etc.). The security code is always required, however, when disarming the system. The keypad allows the user to arm and disarm the system, and perform other system functions, such as bypassing zones, and display zone descriptors. Zone and system conditions (alarm, trouble, bypass) are displayed in the Display Window. When an alarm occurs, keypad sounding and external sounding will occur, and the zone(s) in alarm will be displayed on the keypad. Pressing any key will silence the keypad sounder for 10 seconds. Disarming the system will silence both keypad and external sounders. When the system is disarmed, any zones that were in an alarm condition during the armed period will be displayed (memory of alarm). To clear this display, simply repeat the disarm sequence (enter the security code snd press the OFF key) again. The keypads also feature chime annunciation, and 3 panic key pairs, or individualpanickeys (dependingon keypadtype see Panic Keys), for silent, audible,fireor personalemergencyalarms. These keys cannoti~ the central stationof an alarm condition,if that serviceis comected. The followingis a brief list of system commands. For detailedinformation concerningsystemiimctions,referto the User s Manual. Disarmed, Not Ready...Before arming, the system must be in the READY condition(all zones must be intact).if the NOT READY message appears, press the READY [*] key to displayfaultedzones. Arming Away... Entercode+ AWAY [2]. Arming Stay... Entercode + STAY [3]. Arming Instant... Enter code + INSTANT [7]. Arming Maximum... Enter code + MAXIMUM [4]. Disarming... Enter code + OFF [1]. Bypassing Zones...Enter code + BYPASS [6]+ zone number(s). Forced (Quick) Bypass... (If enabled) To automatically bypass all faulted zones, use the Quick Bypass method: Enter code + BYPASS, then wait for all open zones to be displayed. Arm when display indicates bypass and ready to arm. Chime Mode... Entercode+ CHIME [9]. To turnchimeoff, entercode+ CHIME again. SUMMARY OF ARMING MODES Features for Each Arming Mode Arming Exit Entry Perimeter Interior Mode Delay Delay Armed Armed AWAY Yes Yes Yes Yes STAY Yes Yes Yes No I INSTANT I Yes I No I Yes I No I [-MAXIMUM i Yes I No I Yes I Yes I -65-

Relay~owerline Panic Keys Carrier Devices (if used) 4285 Module (if used) Exit Alarm Displays (if programmed) There are three lettered keys or (on some keypads, panic key pairs) that, if programmed, can be used to manually initiate alarms and send a report to the central station. Each can be individually programmed for 24-hour Silent, Audible, Personal or ~ Fire Emergency responses. The panic function is activated when the appropriate lettered key is pressed for at least 2 seconds, or the appropriate key pair are pressed at the same time. The panic functions are identified by the system as follows: Keys Displayed as Zone Notes: [A, or [11& [*I 95 Keys [A], [B], [C] are not on all [B],m[*Ik [#l 99 keypads. Key [D], if present, is not active [C], or [3]& [#] 96 here. Important: For the Silent Panic functions to be of practical value, the system must be connected to a central station. If relay outputs (via a 4204, or 4229), or Powerline Carrier devices are used, two keypad entries available to the user are included. They can manually activate or deactivate the device(s) for starting or stopping some action, such as turning lights on or off, etc. These keypad entries are: Security Code + [#] + [7] Security + Device # activates (starts) that device. Code + [#] + [8] + Device # de-activates (stops) that device. Refer to the separate instructions supplied with the 4285 module for information concerning its operating procedures. Note: The 4285 module cannot be used to add user codes in this system. User codes must be added by using a wired keypad. * A display of CANCELED ALARM or CA and a zone indication will appear if an exit or interior zone contained a fault during closing at the time the exit delay ended (e.g., exit door left open), but the system was disarmed during the entry delay time. The alarm sounder and keypad sound continuously, but stop when the system is disarmed. No message will be transmitted to the central station. A display of!exit ALARM or EAt and a zone indication will appearif an exit or interiorzone containeda fault duringclosingat the time the exit delay ended, but the system was NOT disarmed during the entry delay time. The alarm sounder and keypad sound continuously until the system is disarmed (or timeout occurs). An exit alarm message is sent to the central station. The EXIT ALARM display, etc. will also result if an alarm from an exit or interior zone occurs within two minutes after the end of an exit delay. In any of the above cases, use a second OFF sequence (code plus OFF key) to clear the display. -86-

Trouble Conditions (See Troubleshooting Guide also) General Information The word CHECK on the Keypad s display, accompaniedby a rapid beeping at the Keypad, indicatesthat there is a trouble conditionin the system. The audible warning sound can be silenced by pressing any key. Instructusers to callfor serviceimmediatelyupon seeingany of the following messages. Check and A display of CHECK and one or more zone numbers indicatesthat Batte@ Displays a problemexistswith the displayedzone(s)and requiresattention. Note: The control will sense a high resistance in the loops on hard-wired zones 2-8 and display CHECK and the affected zone number when the system is in the disarmed mode. It will not be possible to arm the system as long as this condition exists (unless this zone is bypassed). If the system is in the armed mode when the high resistance condition occurs, this display will not appear, but will do so as soon as the system is disarmed. Check the sensor or the loop wiring for the displayed zone. When the problem has been corrected, the display can be cleared by entering the OFF sequence (code plus OFF key) twice. * A display of CHECK and 09 indicates that communication between control and a zone expander or wireless receiver is interrupted. Check the wiring and DIP switch settings on the units.. A display of RAT (Fixed-wordkeypads)or SYSTEM LO BAT (Alpha keypads)with no zone number indicatesthat the system smain standby batteryis weak. Telephone Line Failure Power Failure Other Displays (FixedWord displaysare in parentheses) A display of 94 (Fixed-wordkeypads),or Telco Fault (Alphakeypads), indicatesthat a monitoredtelephoneline (if programmedin field *2) has been cut (or disconnected). Dependingon howthe systemwas programmed, the keypadmay also producea troublesound,and the externalsoundermay be activated(silenceby enteringinstallercodeplus OFF). If there is no keypad display at all, and the POWER indicator (if present) is not lit, operatingpowerfor the system has stoppedand the systemis inoperative. If the message AC LOSS (Alpha keypads) or NO AC (Fixed-word keypads)is displayed, and the POWER indicator (if present) is off, the keypadis operatingon batterypoweronly. If the battery standby capacity is used up during a prolonged AC power outage, the control sauxiliarypowerwill shutdownto minimize deepdischargeof the battery. Busy-Standby (di). If this remainsdisplayedfor more than 1 minute,the systemis disabled. Modem Comm (CC) The system is in communicationwith the central stationfor changeof ftmctionor statusverification. Coxnm. Failure (FC) A communicationfailurehas occurred. Open Circuit (OC) The keypadis not receivingsignalsfromthe controland sees an opencircuit. Long Rng Trbl (bf) Back-upLRRcommunicationfailure. -87-

SYMPTOM 1. Low Batterymessageon keypad. 2. Periodic beep(s)from keypad. 3. Nuisanceor phantomalarm. 4. Intrusionalarmfornoapparentreason. 5. CEJICK andzonenumber 2-8 isdisplayed. SYSTEM POSSIBLE CAUSE la. Bat or System Lo Bat (no zone Nos.) 2a. System is in TEST mode. 3a. Sensors not properly installed, wired, or monitored. 4a. Protected door or window opened while system armed. 4b. Improper user operation of exitientry delays. 4c. Magnets located too far from switches, an~or doors and windows not properly aligned. 5. Control has sensed a high resistance condition on a loop in one of the hardwired zones (2-8). la. REMEDY System battery is low or missing. 2a. Enter Code + OFF to exit TEST mode. 3a. Check installation to see if in accordance with established procedure. 4a. Check with all occupants of protected home. 4b. Check setting of entry delay. Exit delay is 40 seconds longer than the entry delay time. Remind user of same. 4c. Check all openings for proper switch and magnet orientation. 5. Check the sensor or the loop wiring in the affected zone. The system will not arm until this condition is corrected (or the affected zone is bypassed). SYMPTOM 1. ACPOWER light Off. z. Digitalcommunicator messagenotbeing received. 3. Doesnotarmproperly. 4. VISTA-20HW doesn trespondtokeystrokeson keypad. CONTROL POSSIBLECAUSE la. Interrupted AC powersupply. 2a. VLSTA-20HW in TEST mode. 2b. Telephone connection not secure. 2c. Digital communicator malfunctioning. 2d. Telephone number in program needs prefm or access code. 2e. Telephone call to central monitoring station requires operator assistance. 3a. Ready light not on. - 4a. 4b. 4C. M. CC or MODEM COMM displayed. all or System Busy displayed. E4 or E8, or Standby System Busy displayed. Keypad address setting incorrect. REMEDY la. Check transformer connection and Powerline circuit breaker. 2a. Remove from TEST mode. 2b. Check all connections. 2c. Check with a different VISTA-20HW. 2d. Program prefm or access code into the VLSTA-20HW. 2e. VISTA-20HW system cannot work in this situation. 3a. Check for faulted zones and make intact, I or use B~ass arming, if desired. 4a. System is in communication with downloader at central station. Wait until download session is finished. 4b. System has just been powered and is in its one minute initialization. To bypass this time, press # + O. 4C. More zones have been programmed than the zone expansion modules can handle. 4d. Keypads must be set for address 31 (nonaddressable mode). SMOKE DETECTOR SYMPTOM I POSSIBLECAUSE I REMEDY 1. Detectoralarms,noaw I la. Dust,dirtinsensingchamber. I la. Cleanunit sensingchamber with parentreason. - vacuum cleaner W;unit s instructions. lb. Improper location. lb. See unit s instructions for locations to avoid. Relocate as necessary. lc. Unit malfmctioning. lc. Replace detector. 2. Detector sirensounds. 2a. Unit not receiving required power. 2a. Check for proper installation of battery. Try new battery. 2b. Unit malfimctioning. 2b. Replace detector. i I -88-

PLEASE, CONTACTING TECHNICAL SUPPORT Before you call Technical Support, be sure you: READ THE INSTRUCTIONS! Check all wiring connections. Determine that the power supply and/or backup battery are supplying proper voltages. Veri& your progr amming information where applicable. Note the proper model number of this product, and the version level (if known) along with any documentation that came with the product. Note your ADEMCO customer number and/or company name. Having this information handy will make it easier for us to serve you quickly and effectively. You may contact Technical Support via Toll-Free FAX. Please include your return FAX number. You will receive a reply within 24 hours. You may also contact Technical Support via modem to ATLIS BBS, Technical Support s Electronic Bulletin Board System. Replies are posted within 24 hours. East Coast Technical Support: 1-800-645-7492 (8 a.m.-6 p.m. E. S.T.) West Coast Technical Support: 1-800-458-9469 (8 a.m. 5 p.m. P. S.T.) Technical Support FAX Number: 1-800447-5086 ATLIS BBS Electronic Bulletin Board System: 1 516496-3980 (1200 9600 Baud, 8 Data Bits, 1 Start/Stop Bit, No Parity) ATLIS FAX Automated Fax Retrieval System: 1-800-573-0153 l 516-921-6704/Ext. 1667

REGULATORY AGENCY STATEMENTS UL NOTICE: This is a Grade A residential system. FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer s instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: If using an indoor antema, have a quality outdoor antenna installed. Reorient the receiving antenna until interference is reduced or eliminated. c Move the radio or television receiver away from the receiver/control. c Move the antenna leads away from any wire runs to the receiver/control. Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user or installer may find the following booklet prepared by the Federal Communications Commission helpfhl: Interference Handbook This booklet is available from the U.S. Government Printing Office, Washington, DC 20402.. The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User s Manual. Unauthorized changes or modifications could void the user s authority to operate the equipment. FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 STATEMENT This equipmentcomplieswithpart 68 of the FCC rules. On the front coverof this equipmentis a label that contains, amongotherinformation,the FCC registrationnumber and ringer equivalencenumber (REN) for this equipment.if requested,this informationmustbe providedto the telephonecompany. This equipmentuses the followingjacks: An RJ31X is used to connectthis equipmentto the telephone network. The REN is used to determinethe quantity of deviceswhich may be connectedto the telephoneline. ExcessiveRENs on the telephoneline may resultin the devicesnot ringingin responseto an incoming call. In most, but not all iireas,the sum of the RENs shouldnot exceedfive (5.0). To be certain of the number of devicesthat may be connectedto the line, as determinedby the total RENs, contact the telephonecompanyto determinethe maximumren forthe callingarea. If this equipment causes harm to the telephone network, the telephone company will notify you in advancethat temporarydiscontinuanceof servicemaybe required.if advancenoticeis not practical,the telephonecompanywill notifythe customeras soonas possible.also, you will be advisedof yourright to filea complaintwiththe FCC if you believenecessary. The telephone companymay make changesin its facilities,equipment,operations,or proceduresthat couldaffectthe operationof the equipment.if this happens,the telephonecompany will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service. If trouble is experienced with this equipment, please contact the manufacturer for repair and warranty information. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved. There are no user serviceable components in this product, and all necessary repairs must be made by the manufacturer. Other repair methods may invalidate the FCC registration on this product. This equipment cannot be used on telephone company-provided coin service. Connection to Party Line Service is subject to state tariffs. This equipment is hearing-aid compatible. When programming or making test calls to an emergency number, briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak hours; such as early morning or late evening. -90-

specifications V-ISTA-20HW 1. Physicak 12-W W x 14-1/2 H x 3 D (318mm x 368mm x 76mm). SECURITY CONTROL 2. Electrical VOLTAGE INPUT: 16.5VAC from plug-in 25VA transformer, Ademco No. 1321/TF2 (in U.S.A.). RECHARGEABLE BACK- UP BATTERY: 12VDC, 4AH (Gel type) minimum. Charging Voltage: 13.8VDC. ALARM SOUNDER: 12V, 2.o Amp output can drive 12V BELLS or can drive one or two 702 (series connected) self-contained 20-watt sirens. Do not connect two 702s in parallel. AUXILIARY POWER OUTPUT: 12VDC, 600mA max. Interrupts for 4- wire smoke detector reset. Note: For UL installations, Alarm Sounder plus Auxiliary Power currents should not exceed 700mA total. STANDBY TIME: (see formula in Section 13. FINfi POWER UP for required battery size needed). FUSE: Battery (3A) No. 90-12. 3. Communication: FORMATS SUPPORTED: Ademco Express, 10 charactershec,dtmf (TouchTone)DataTones,1400/2300Hz ACK, 1400Hz KISSOFF. Ademco Contact ID Reporting, 10 characters/see.,dtmf (TouchTone)Data Tones,1400/2300Hz ACK, 1400Hz KISSOFF. Ademco Low Speed, 10 pulses/see,1900hz DataTone, 1400Hz ACWKISSOFF. Radionics/SESCOA 20 pulseshec,1800hz Data Tone, 2300Hz ACWKISSOFF. Can report O-9, B-F Line Seize: Double Pole. Ringer Equivalence: 0.7B. FCC Registration No.: AC 398U-68192-AL-E. 4. Maximum Zone Resistance: Zones 1-8= 300 ohms excluding EOLR 4127 1. Physicak 5-5/8 W x 4-11/16 H x 7/8 D (143mm x l19mm x 22mm). REMOTE KEYPAD 2. Electrical: Voltage Input: 12VDC, Current Drain: 20mA. 3. Interface Wiring To controlpanel skeypadconnectionpoints. RED: 12VDCinput(+) auxpwr. GREEN: Data Outto Control. YELLOW: Data In horncontrol. BLACK Ground. 4137AD & 5137AD 1. Physicak 8-2/5 W x 4-3/4 H x 1-1/10 D (213mmx 121mmx 28mm). REMOTE KEYPADS 2. Electrical VoltageInput: 12VDC. Current Drain: 60mA (4137A.D). 9onA(5137AD). 3. Interface Wiring RED: BLUE: GREEN: YELLOW BLACK 12VDC input (+) auxiliary power. 18VDC input from optional No 1350 or 1360 Power Pack (not usable for UL installations). Data Out to Control. Data In from Control. Ground ( ) connection horn optional No. 1350/1360 Power pack. -91-

6127 REMOTE KEYPAD 6128 REMOTE KEYPAD 6137 REMOTE KEYPAD 6138 & 6139 REMOTE KEYPADS 4219 WIRED EXPANSION MODULE 4204 REI.AY MODULE 4229 WIRED EXPANSION/ RELAY MODULE 4285 VIP MODULE 1. Physical: 5-3/4 W x 4-3/4 H x 1 D (146mm x 121mm x 26mm), 2. Electrical: Voltage Input: 12VDC; Current Drain: 20mA. 3. Interface Wiring: Same as 4127. 1. Physical: 5-3/4 W x 4-3/4 H x 1 D (146mm x 121mm x 26mm). 2. Electrical: Voltage Input: 12VDC; Current Drain: 30nA. 3. Interface Wirin~ Same as 4127. 1. Physicak 6-1/4 W x 4-3/4 H x 1 D (159mm x 121mm x 26mm). 2. Electrical: Voltage Input: 12VDC; Current Drain: 85mA, 3. Interface Wiring Same as 4127. 1. Physicak 6-1/4 W x 4-3/4 H x 1 D (159mm x 121mm x 26mm). 2. Electrical Voltage Input: 12VDC; Current Drain: 100mA. 3. Interface Wiring Same as 4127. 1. Physical: 6-1/2 W x 4-1/4 H x 1-IJ4 D (169mm x 108mm x 32mm). 2. Electrical Voltage Input: 12VDC; Current Drain: 35rnA. 3. Interface Wiring: Same as 4127. 4.8 EOLR LOOPS (A-H): LoopA can be set for fast (10-15msec) responseto an open. 1. Physicak 6-1/2 W x 4-1/4 H x l-1./4 D (169mm x 108mm x 32mm). 2. Electrical: Voltage Input:12VDC; Current Drain: 15mA(Relays ofl). 180rm4(Relays on). 3. Interface Wiring Same as 4127 4. Four Output Relays: SPDT Contacts, Rating: 2A max at 28VDC/AC 1. Physical: 6-1/2 W x 4-1/4 H x 1-1/4 D (169mm x 108mm x 32mm). 2. Electrical: Voltage Input.-l2VDC; Current Drain: 35mA (Relays off). 100mA (Relays on). 3. Interface Wiring Same as 4127. 4.8 EOLR LoOPS (A-H): Loop A can be set for fast (10 15msec) response to an open. 5. Two Output Relays: - SPDT Contacts, Rating: 2A max at 28VDC/AC. 1. Physicak 6-1/2 W x 41/4 H x l-1/4 D (169mm x 108mm x 32mm). 2. Electrical: Voltage Input: 12VDC Current Drain:160mA. 3. Device Address: Permanentlysetto address4. 4. Interface Wiring Referto Section 8.4285 VIP (VISTA Interactive Phone) MODULE. 5. Telephone Line Connections: Referto Section 8.4285 VIP (VISTA Interactive Phone) MODULE. w * -92-

No. 1321/TF2 16.5VAC, 25VA Plug-In Transformer. No. 4300 Powerline Carrier device Interface AC Transformer. Sounders Ademco AB-12M 10 Motorized Bell & Box Ademco 10I133E12M 10 Motorized Bell & Box Ademco 702 Outdoor Siren Ademco 719 2-Channel Siren Ademco 747 Indoor Siren Ademco 747UL Indoor Siren Ademco 744 Siren Driver Ademco 745X3 Voice Siren Driver Ademco 705-820, 5-inch Round Speaker Ademco 713 Speaker System Sensor PA400B (beige)/pa400r (red) Indoor Piezo Sounder Motor bell & box. UL Grade A. 100 ma current draw. Motor bell & box. UL Listed. 100 ma current draw. Self-contained 6 12 volt siren (driver built-in) and weatherproof for outdoor use. Can be wired for either a steady or warble sound. Two-channel, self-contained 6-12-volt siren (driver built in). 109dB @ 10 f~t. 550mA current draw. Self-contained 12 volt siren (driver built-in) for indoor wall mount. 747F available for flush mounting. Self-contained siren (driver built-in) for indoor wall mount. UL Listed. 6 jumper-selected sound outputs. Rated at l19db with use of an 8-ohm 30 watt speaker. Voice siren driver with English, Spanish and French voice messages. Separate messages for Fire and Burglary. Use with 8-ohm speaker. UL Listed. 15-watt, 8-ohm speaker. 40-watt, 8-ohm, indoor/outdoor speaker. Indoor piezo sounder (red or beige), rated at 90 db @ 10 feet. Compatible Z-Wire.%stem Sensor Sm-oke Detectors 2&0T Photoelectric w/heat sensor, direct wire. 2400 Photoelectric, direct wire. 2400TH Photoelectric wlheat sensor, direct wire. 2451 Photoelectric w/b401b base. 2451TH Photoelectric w/heat sensor & B401Bbase. 1400 Ionization, direct wire. 1451 Ionization w/b401b base. 2451 Photoelectric duct detector w/dh400 base. 1451DH Ionization duct detect. w/dh400 base. Compatible 4-Wwe System Sensor SmokdCombustion 1412 4-wire ionization products of combustion detector. Detectors 2412 4-wire photoelectric smoke detector. 2412TH 4-wire photoelectric smoke detector w/135~ F (579 C) heat detector. A77-716B EOL relay module (supervisory module for wired 4-wire fire zone). 2112124T Low-profile 4-wire photoelectric smoke detector w/135e F (57! C) heat detector. -93-

l-minute Delay......... 54 101 IBE12M... 44, 93 1321mf2... 11, 14, 54 1321/Tf2 AC Transformer... 10 1321flf2 Transformer.... 32 1400.................. 93 1412......... 93 1451... 93 1451 DH... 93 15-Second Dialer Delay (Burgla~)... 74 15-Second Dialer Delay, Burglary...65 2,000 Ohm EOLR... 21 2-Digit Phone Access Code... 42 2-Digit Phone Code... 43 211224T... 93 2300T... 93 24-Hour... 70 24-Hour Audible Alarm... 70 24-Hour Silent Alarm...... 70 2400... 93 2400TH...- 93 2412... 23, 93 241 2TH... 23,93 2451... 93 2451TH... 93 3+1 And4+l Expanded Formats...62 3+1 And 4+1 Standard Formats... 62 3+1 Or 4+1 Standard Format... 66, 76 3-Digit Number... 56,57 4+2 Format... 62 4-Wire Smoke Detectors... 21 4127... 16, 91 4127... 9 4137ad... 9, 16, 17, 91 4142TR Cable... 15,33, 48 4146... 48 4146 Keyswitch... 10 4204... 10>20,31,36, 52,78,86,92 4219... 9,27,30,31,75,92 4229... 9, 10,20,27,30,31,36,52, 75,78,86,92 4285... 10, 11, 14,39,40,42,43,52,92 4285 VIP Module... 39,40,41,42,56, 59, 60,80,86 43OO Transformer...10. 11, 14, 15, 31, 32, 33, 54 487 12... 17 488 12... 17 5137 AD... 9, 11, 16, 17, 19,24, 28,36,42, 45, 47,91 513nRK... 17 6127... 16,92 6127... 9 6128...... 16, 17,92 6128.... 9 6137... 9, 16,17,92 6137... 16 6138... 9, 16, 17,92 6139... 9, 11, 16, 17, 19,24,28,36,42,45,47, 92 6139TRK... 17 702...93 705-820... 93 713... 93 719...93 74... 44, 93 745x3...u. 93 747... 93 m 747UL... 44, 93 7720 PIUS.................................................................. 10,47 9-Pin Connector...48 -A- A77-716B... 23, 93 AB-12M 10 Motorized Bell& Box... 44, 93 AC Loss Report Code... 66 AC Loss Report Code... 77 AC Power Supply... 11 AC Restore Report Code... 67, 78 AC Transformer... 14 Addressable Keypads... 16, 39 Addressable Type Keypads... 17 Ademco Contact ld... 11, 62 Ademco Express... 11, 61, 91 Ademco Low Speed... 11, 91 Alarm Bell ~meout... 45, 72 Alarm Output... 11,45,55 Alarm Restore Report Code, 1st Digit... 67,78 Alarm Sounders... 45 Alpha... 20 Alpha Descriptor...- 58 Alpha Descriptor... 29, 56 Alpha Keypad... 20 Alpha Keypads... 9 Alpha Vmabulay... 56 Alpha Vocabulary List... 57 ~ Answering Machine... 42, 68, 80 Arm Away/Stay Report Code... 67,7 7 Arming Away......- 85 Arming instant... 85 Arming Maximum......... 85 Arming Modes... 85 Arming Stay... 85 Audible Exit Warning... 72 Audio Alarm Verification (AAV)... 10,39,52 Auxiliary Output... 55 Auxiliary Power Output... 11 -B- Baby-SitterCode... 10, 84 Back-Up Batie~... 11, 15,46,54 Basic Hardwired Zones... 9 BAT... 88 Battety Connector Cable... 55 Batiery Size... 54 Battery Standby Formula... 55 Bells...- 45 bf... 87 Busy-Standby... 87 Bypass Report Code... 66, 77 Bypass Restore Report Code... 67,78 Bypassing Zones...- 85 -c- Cabinet Lock... 12 Caller ID Unit... 40,41 Cancel Report Code...- 67, 77-94-

cc... 87,68 Central Station............. 76 Character (Ascii) Chati......... 60 Character Chart......... 56 Character List......... 59 Charging Voltage............... 91 Check 09 Message... 30 Chime Mode... 85 Comm Failure... 61, 87 Communication... 91 Communication Failure... 87 Communication Formats Supported... 11 Compatible 2-W]re Smoke Detectors... 22,93 Compatible 4-Wire Smoke/Combustion Detectors...23.93 Compatible Glass Break Detectors... 23 Compatible Sounders... 44 -c- Confirmation Of Arming Ding... 45,73 Contact ID... 47,52,63,66,76 Contact ID Event Codes... 63 Contact ID Reporting... 91 Control Cabinet... 12 Control s Circuit Board... 13 Custom Alpha Editing... 78 Custom Words... 59, 60 -D- Default Descriptor.............. 57 E4... 88 E8... 88 Eagle 1241... 52 Earth Ground... 15,54 EEROM Memory... 19 Entry Delay... 69, 1,88 Entry/Exit Burglay... 1,2 EOL Resistor... 21, 22, 26, 30, 48 EOL Resistors... 18 EOLR... 27,48 Event Log 80% Full Repoti Code... 67, 78 Event Logging... 11, 67, ~ Exit Alarm............ Exit Delay............. 69,88 Exit Error Report Code... 66, 77 Exit Programming Mode... 80 Expanded or 4+2 Format... 66,76 External Sounders... 44 Facto~Defaults...2O Fast Busy 5gnal... 41 FC... 61,87 FCC... 90 Fire Alarm Sounding... 21 Fire Sounder Timeout... 45,72 Fixed-Word Keypads...9 Forced (Quick) Bypass... 85 Forced Bypass... 19 Forced Bypass Function... 71 Formats... 61 Fuse... 91 Default Values................. 75 Device Address... 27,47 Device Number... 37 dl... 87,88 Dialer Programming...73 DIP Switch... 27,31 Disarmed, Not Ready...- 85 Disarming...85 Download information... 79 Download Phone Number... 79 Download Phone Number... 68 Downloading... 68 Duress Code... 10, 84 -E- -F- -G- Group Restores For Trouble, Bypass... 67,78 -H- Handshake... 61 Hard-Wired Zones... 21 Hayes Modem... 11,81 IBM Compatible Personal Computer (PC)...81 IBM Personal Computer... 19 Ideal Model 61-035... 15,54 IEI 7351 Series Detectors... 23 Indicator Panel... 46 Initialize Download ID And Subscriber Acct. No. For Downloading... 80 Initialize Download ID And Subscriber Acct. No. For Downloading... 68 Input Device Types... 75 installer Code... 19,71 Interactive Mode... 36,38 Interactive Mode Programming... 20, 24,36, 50 interior W/Delay...7O Interior, Follower..... 69 Keypad Connections... 17 Keypad Panic Keys... 10 Keypads... 16, 17 Keyswitch Enable... 19,20,72 Keyswitch Operation... KissOff... :; LED indications... 51 LEDs... 48 Line Seizure Witing... 41 Lock... Lock Switch... 46, z Long Range Radio... 10,47 Long Rng Trbl... 87 Low Bat Report Code.......... 66, 77 Low Bat Restore Report Code......... 67,78 Low Battery Message................. 55,88 Low Speed... 61 LRR Communication Failure... 87 Magnets... 68 Main PC Board... 12 Master Code... 64 Momentary Switch...48 -I- -K- -L- -M- -95-

Monitored Telephone Line... 87 Model 112... 48 Modem... 19 Modem Comm... 87, 88 -N- No Alarm Response... 70 No. 1321~F2... 93 No. 4300... 93 No, 467 (12v, 4AH) Batie~... 54 No. A77-716B... 22 Number Of Reports In Armed Period..... 68, 79 -o- Oc... 87 Off-Premises Phone... 43 On-Premises Phone... 43 Open Circuit............ 87 Open Report Code... 67, 77 Optima 24 Plus FAX 96 Modem... 81 Option Selection... 52,79 Output Devices... 34, 78 Output Relays... 10,36 Output To Long Range Radio... 72 -P PA400B... 44, 93 PA400R... 44,93 PABX Access Code... 73 PABX Access Code.... 64 Panic Keys... 86 Partition Default... 75 Partitions... 9 Perimeter Burglary... 69 Periodic Test Report... 65, 74 Phone Access... 39, 42 Phone tine... 14 Phone Line Monitor Enable... 68, 79 Phone System Select... 84, 74 Power Failure..... 87 Power LED... 54 Power Up [n Previous State... 73 Powerline Carrier Device... 37 Powerline Carrier Device House ID...36. 71 Powerline Carrier Devices (X1 O)... 10, 11, 31, 32, 36,78,86 Primary Phone No.... 64, 73 Primary Subscriber Account. No.... 73 Primary Subscriber Account. No. (Partition 1)...64 Primary Subscriber Account. No. (Partition 2)...64 Program Mode... 19 Program Upload Or Download Time... 82 Programming Information... 19 Pulse Dialing,... 39 -Q- Quad Conductor Cable... 16 Quick Arm... 85 Quick Arm Enable... 19,71 -R- Radionics/Sescoa... 91 Ready LED... 54 Relay Outputs... 31 Relay Programming... 20 Relays... 31 Remote Keypads... 9 Remote Programming... 81 Report Code... 75,77 Report Code Formats... 61 - Report Codes... 66,76 Report Format... 74 Report Format, Primary/Secondary... 65 Response ~me... 51, 75 Restore... 78 Ring Detection... 68 I%ng Detection Count For Downloading... 79 RJ31 XJack... 14,40,41 -s- Scrolling... 56 Secondary Phone No.... 64, 73 Secondary Subs Account. No.... 73 Secondary Subscriber Account. No.... 64 Secondary Subscriber Account. No. (Partition 1)...64 Security Codes... 84 Se=odRadionics... 11, 61 Sescoa/Radionics Select... 65,74 Set All Program Fields To Default Values... 80 Silent Alarm... 70 Silent Panic... 86 Single Alarm Sounding Per Zone... 72 Single Alarm Sounding Per Zone/Armed Period...45 Sirens...45 SmartModem 1200... 81 Sounders... 93 Split/Dual Reporting... 65, 74 Standby-System Busy... 88 Supewised Hre... 70 Supplementary Power Supply... 17 System Communication... 61 System Lo Bat... 88 System Operation... 37 System Status And Restore Report Codes...66. 67.76 System Status Report Codes... 77 -T- Tamper Protection... 27 Tamper Switch... 48 Technical Suppoti... 89 Telco Fault... 87 Telco Line... 41 Telephone Line Monitoring... 10 Telephone Line Failure... 87 Test Mode... 83 Test Report Code... 66,77 Test Report Offset...65. 74 Test Restore Report Code... 67,78 Touch-Tone...39 Touchtone Phone... 43 Trouble By Day/Alarm By Night... 69 Trouble Condition... 87 Trouble Report Code... 66, 77 Trouble Restore Report Code... 67,78 -u- UL... 15, 17,32,44, 55; 90,91-98-

Verification Feature... 24 Verify Operation...?... 21 V-Link@ Downloading Software... 11, 19, 81 V-Link@ Downloading Software Diskette... 82 Vocabulary List...- 60 Voice Module Access Code... 42 Voice Module Phone Code (4285).......... 71 Wired Expansion Zones... 28 Wired Zone Expansion... 19, 20, 71 Wiring 2-Wire Smoke Detectors... 21 Wiring 4-Wire Smoke/Combustion Detectors On Zones 2-7... 22 Wiring Length/Gauge Chart... 16 Wiring Table... 14 Word Stting... 59 Worksheet... 55 X-10 (also see PowerLine Carrier Devices)........31.37 -v- -w- -x- -z- Zone Assignment/Alarm Report Codes... 75 Zone Descriptors... 11,42, 58,60 Zone Expansion... 27 Zone List... 20 Zone Lists For Output Devices... 38,78 Zone Not Used............. 69 Zone Programming........ 20 Zone Sounds And Timing............ 72 Zone Type... 24,28,75 Zone Type 01 Entry Delay... 72 Zone Type Default... 75 Zone Types... 37,69-97-

WARNING THE LIMITATIONS OF THIS AUUtM SYSTEM While this System is an advanced design security system, it does not offer guaranteed protection against burglary, tire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example: 9 Intrusion detectors (e.g., passive infkared detectors), smoke detectors, and many other sensing devices will not work without power. Battery-operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. A user may not be able to reach a panic or emergency button quickly enough. While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide eady warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense tires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sensea firstflooror basementfire. Finally,smokedetectorshavesensinglimitations.No smokedetectorcan sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessnessand safety hazards like smoking in bed, violentexplosions,escaping gas, improperstorageof flammablematerials,overloadedelectricalcircuits,childrenplayingwith matches,or arson.dependingon the nature of the fire and/orlocation of the smokedetectors,the detector,even if it operatesas anticipated, may not providesufficientwarningto allow alloccupantsto escapein time to preventinjuryor death. Passive Infrared Motion Detectorscan only detect intrusionwithinthe designed ranges as diagramed in their installationmanual. Passive Infrared Detectorsdo not provide volumetric area protection.they do create multiple beams of protection, and intrusion can only be detectedin unobstructedareas coveredby those beams. They cannot detect motion or intrusionthattakesplace behind walls, ceilings,floors,closed doors,glass partitions,glassdoors,or windows. Mechanicaltampering,masking,paintingor sprayingof any materialon the mirrors,windowsor any part of the opticalsystemcanreducetheir detectionability.passive InfraredDetectorssensechangesin temperature;however,as the ambienttemperatureof the protectedarea approachesthe temperaturerange of 90 to 105 F(32 to 40 C),the detectionperformancecan decrease. Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepersif they are locatedon the other side of closed or partly open doors.if warningdevicesare locatedon a differentlevelof the residencefrom the bedrooms,then they are lesslikelyto wakenor alertpeopleinsidethe bedrooms.even personswho are awake may not hear the warning if the alarmis muffledby noise from a stereo,radio,air conditioneror other appliance,or by passing traffic. Finally,alarmwarningdevices,howeverloud,may not warn hearing-impairedpeople. Telephonelinesneededto transmitalarmsignalsfrom a premisesto a centralmonitoringstationmaybe out of service or temporarily out of service. Telephone lines are also subject to compromiseby sophisticated intruders. Evenif the systemrespondsto the emergencyas intended,however,occupantsmayhaveinsticient time to protectthemselvesfrom the emergency situation.in the caseof a monitoredalarmsystem,authoritiesmay not respondappropriately. This equipment,like other electricaldevices,is subjectto componentfailure. Even thoughthis equipmentis designed to last as long as 20 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. The security keypad (and remote keypad) should be tested as well. Wireless transmitters (used in some systems) are designed to provide long battery life under normal operating conditions. Longevity of batteries maybe as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device being used. External factors such as humidity, high or low temperatures, as well as large swings in temperature, may all reduce the actual battery life in a given installation. This wireless system, however, can identify a true low battery situation, thus allowing time to arrange a change of battery to maintain protection for that given point within the system. Installing an alarm system may make the owner eligible for a lower insurance rate, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices, Users of alarm systems owe it to themselves and their loved ones to learn about these developments. -9s-

ii ;::l ii,,,, Figure 20. VISTA-20HWSUMMARY OFCONNECTIONS -99-

ADEMCO LIMITED WARRANTY Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, subsidiaries and affiliates ( Seller ), 165 Eileen Way, Syosset, New York 11791, warrants its products to be in conformance with its own plans and specifications and to be free born defects in materials and workmanship under normal use and service for 18 months from the date stamp control on the product or, for products not having an Ademco date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply. Seller s obligation shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product which is proved not in compliance with Seller s specifications or proves defective in materials or workmanship under normal use and service. Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Ademco factory service. For warranty service, return product transportation prepaid, to Ademco Factory Service, 165 Eileen Way, Syosset, New York 11791. THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER S OWN NEGLIGENCE OR FAULT. Seller does not represent that the products it sells may not be compromised or circumvented; that the products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the products will in all cases provide adequate warning or protection. Customer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery, ilre or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLERS MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty replaces any previous warranties and is the only warranty made by Seller on this product. No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized. N7526-2V1 4/96 ALARM DEVICE MANUFACTURING CO. A DIVISIONOF PITTWAY CORPORATION 165 Eileen Way, Syosset, New York 11791 Copyright @ 1995 Plll_WAY CORPORATION