PERS-400B PERSONAL REPORTING SYSTEM BY BY Installation, and Operation Instructions USA & Canada (800) 4-587 & (800) 9-0 (760) 48-7000 - Toll Free FAX (800) 468-40 www.linearcorp.com
CONTENTS. FRONT PANEL FEATURES.............................................. REMOVING BOTTOM COVER............................................ BOTTOM FEATURES......................................... 4. OPTIONAL VB-4B VOICE BOARD INSTALLATION............................ 5. OPTIONAL RELAY OUTPUT CONNECTIONS................................ 6. OPTIONAL REMOTE SPEAKER/MIC CONNECTIONS......................... 7. BACKUP BATTERY.................................................. 8. INSTALL TRANSFORMER............................................. 9. APPLY POWER - SELECT DIALING METHOD............................... 0. TRANSMITTER INSTALLATION OPTIONS................................. INSTALLING SINGLE TRANSMITTERS.................................... INSTALLING MULTIPLE TRANSMITTERS.................................. TESTING TRANSMITTERS............................................ 4 4. ERASING TRANSMITTERS............................................ 4 5. LOCAL PROGRAMMING WITH RA-400.................................. 4 6. TELEPHONE CONNECTIONS.......................................... 4 7. SYSTEM OPERATION................................................ 5 8. ACTIVITY TIMER................................................... 5 9. AUDIO BOARD OPERATION........................................... 5 0. SPEAKERPHONE OPERATION......................................... 5. SUPERVISORY CONDITIONS.......................................... 6. WIRELESS INSTALLATION TIPS....................................... 6 SPECIFICATIONS..................................................... 6 LINEAR LIMITED WARRANTY............................................ 6 PRODUCT DESCRIPTION The PERS-400B Console is a supervised wireless emergency reporting product designed for medical alert applications. The table-top or wall-mount Console provides pushbutton emergency assistance to anyone who desires additional security and peace of mind. For the visually impaired, each button on the Console is molded with braille characters to identify the button s function. The Console receives signals from up to 6 Linear wireless transmitters. Activating a transmitter causes the Console s digital communicator to send the appropriate alarm report to the central monitoring station via the standard telephone network. In addition to the central station report, audible and visual indications occur and the alarm relay energizes during an emergency activation. The emergency alarm can be triggered by the large button on the face of the Console or with a wireless transmitter. The fi re alarm can be triggered by wireless smoke alarms. The optional activity timer can be set for 8, or 4 hour operation. The emergency alarm will trigger automatically if the time set elapses before an activity transmitter is triggered or the Console s HOME button is pressed. If the optional Model VB-4B voice board is installed, the Console will talk to the user. The digitized voice, will sound emergency, fi re, CO Alarm, timer done soon, and other system operation, setup, and supervisory prompts from a 8 word vocabulary. In addition, the voice board supports -way automatic, -way manual, and -way listen-only audio communications with central station monitoring personnel using the Console s built-in high-sensivity microphone and speaker. The Console can be programmed to act as a remote controlled speakerphone. With the speakerphone mode enabled (Model VB-4B voice board required) the Console will monitor the telephone line for an incoming call. Activating any emergency transmitter (or the Console s button) while the telephone is ringing will cause the Console to seize the line and begin full duplex voice communications. Activating any emergency transmitter (or button) during the call will disconnect the line. The Console will auto-disconnect after 5, 0, or 60 minutes (programmable). Supervised transmitters regularly send status reports to the Console and low battery reports when their batteries are low. When the Console receives a low battery report, the TROUBLE indicator fl ashes. If the Console fails to receive a status report from a transmitter for a period of 4 hours, the TROUBLE indicator will light. All supervisory conditions can sound a local annunciation and be reported to the central station. The Console s digital communicator can route calls to three telephone numbers: primary, secondary, and supervisory. General reporting codes and individual sensor reporting codes are programmable for the 4x format. Alternately, Ademco Contact ID may be selected for the communicator reporting format. Powered by a low voltage plug-in transformer, the Console has provisions for a rechargeable backup battery for operation during AC power outages. A power switch allows for out-of-service storage of the Console without discharge of the battery. The battery is recharged and supervised by the Console. If the backup battery becomes low the POWER light will fl ash and the condition can be reported to the central station. The Console is programmed using Linear s RA-400 remote access software (available on CD and at Linear s Web site: www.linearcorp.com). Refer to the software s built-in help fi le for programming details. TRANSMITTER COMPATIBILITY DXT-4 DXT-6A DXS- DXS- DXS-6A DXT-4 DXS- NOTE: COMPATABILITY WITH THE PERS-400B HAS NOT BEEN VERIFIED BY UL NOTE: NOT A UL LISTED DEVICE UP TO 6 TRANSMITTERS CAN BE USED WITH EACH R A D I O S I G N A L S FIRE DXS-7 DXS-/ PERS-400B ACTIVITY CARBON MONOXIDE DXS-80 DXS-54 TO CENTRAL STATION VIA TELEPHONE OPERATION SUMMARY A variety of Linear s supervised DXS and non-supervised DX format transmitters can be used with the Console. Transmitters can be assigned to the following four functions: Portable, supervised and non-supervised, pendant, belt-clip, or wristband type transmitters (Models DXT-4, DXT-4, DXT-6A, DXS-, DXS-, DXS-6A) and stationary, supervised Model DXS- transmitters are used for medical alert applications. When a medical alert transmitter is triggered, the Console sounds a two-tone siren and an emergency report is sent to the central station. The emergency alarm can also be triggered by pressing the Console s button. FIRE Supervised Model DXS-7 wireless photoelectric smoke alarms trigger the fi re alarm. When the fi re alarm is activated, the Console sounds a repeated series of three beeps and a fi re report is sent to the central station. CARBON MONOXIDE (CO) Supervised Model DXS-80 wireless carbon monoxide detectors trigger the CO alarm. When a carbon monoxide alarm is activated, the Console sounds a repeated series of four beeps and a carbon monoxide report is sent to the central station. ACTIVITY Supervised, switch or motion triggered transmitters (Models DXS-/DXS- and DXS-54) can be used for ensuring human activity. The DXS-54 motion detector will monitor room activity. The DXS- and DXS- transmitters can be wired to a pushbutton or switch for manual activity monitoring. As long as a signal is received at least once every 8,, or 4 hours (programmable) an alarm will not be triggered. 5 minutes before the programmed time expires, the HOME indicator will start blinking and a low pitched beep will sound every ten seconds. The activity timer can be reset with a signal from one of the activity transmitters or by pressing the HOME button on the Console. Failure to reset the activity timer within the programmed time period will cause the Console to sound the two-tone emergency siren and send an inactivity report to the central station. The activity timer can be turned on or off at the Console or through programming.
. FRONT PANEL FEATURES TROUBLE INDICATOR NORMALLY OFF LIGHTS WHEN ANY TRANSMITTERS ARE MISSING (SUPERVISORY) BLINKS SLOWLY WHEN ANY TRANSMITTERS HAVE A LOW BATTERY POWER INDICATOR LIGHTS WHEN AC IS PRESENT BLINKS SLOWLY WHEN BATTERY IS CHARGING BLINKS QUICKLY WHEN AC IS ABSENT ( ON BATTERY POWER) OFF IN TEST AND SETUP MODES BUTTON PRESS AND HOLD TO TRIGGER THE EMEREGNCY ZONE PRESS DURING RING FOR SPEAKERPHONE MODE PRESS DURING SPEAKERPHONE MODE TO DISCONNECT CLEAR BUTTON STOPS ALARM ADDS CANCEL TO AN ALARM REPORT IN PROGRESS PRESS IMMEDIATELY AFTER TO PREVENT REPORT CLEARS INDICATORS STOPS TROUBLE BEEPER PRESS FOR 5 SECONDS TO ADD A TRANSMITTER. REMOVING BOTTOM COVER TO ACCESS THE INSIDE OF THE PRESS THE TWO LOCKING TABS IN AND REMOVE THE 'S BOTTOM COVER REMOVE COVER PRESS TABS IN HOME BUTTON PRESS TO RESET ACTIVITY TIMER PRESS FOR 5 SECONDS TO TURN ACTIVITY TIMER OFF IF ACTIVITY TIMER IS OFF, PRESS FOR HOME INDICATOR 5 SECONDS TO TURN ACTIVITY TIMER ON LIGHTS WHEN ACTIVITY TIMER IS ON BLINKS SLOWLY WHEN LESS THAN 5 MINUTES REMAIN ON THE ACTIVITY TIMER BLINKS QUICKLY WHEN THE ACTIVITY TIMER HAS EXPIRED SENDING INDICATOR NORMALLY OFF FLASHES WHEN IS PLACING A CALL HOME BUTTON COVER ADHESIVE BACKED PLATE TO HIDE THE HOME BUTTON IF THE ACTIVITY TIMER IS NOT USED. BOTTOM FEATURES 6 VAC.5 AMP PLUG-IN TRANSFORMER -VOLT. AMP/HOUR BACKUP BATTERY 4. OPTIONAL VB-4B VOICE BOARD INSTALLATION CONNECT BLACK MICROPHONE WIRE TO CENTER TERMINAL CONNECT RED MICROPHONE WIRE TO THIS TERMINAL PRESS-FIT MICROPHONE INTO ROUND MOUNTING HOLE 4 EXTERNAL SPEAKER, RELAY OUTPUT, AND DIALER POWER TERMINALS AMP AG BATTERY FUSE (HIDDEN) OPTIONAL VB-4B VOICE BOARD SEAT MICROPHONE CAREFULLY ALIGN PINS TO CONNECTORS ON BOTH ENDS OF BOARD LOCAL PHONE JACK TELEPHONE LINE JACK POWER SWITCH TEST BUTTON 5 NOTE: POWER MUST BE OFF AND BATTERY SHOULD BE REMOVED OR DISCONNECTED BEFORE INSTALLING THE AUDIO BOARD BE SURE THAT THE WHITE ARROWS ON AUDIO BOARD POINT TOWARD THE BATTERY AREA PRESS BOARD COMPLETELY INTO CONNECTORS NOTE: AFTER THE AUDIO BOARD IS INSTALLED AND ENABLED, THE WILL SPEAK INSTEAD OF BEEP DURING PROGRAMMING
5. OPTIONAL RELAY OUTPUT CONNECTIONS NOISEMAKER OR VISUAL INDICATOR EXTERNAL POWER SUPPLY FORM "A" DRY CONTACT RELAY 4 VOLTS AT AMP MAXIMUM 5 4 - RELAY NORMALLY OPEN - RELAY COMMON TERMINAL BLOCK CONNECT WIRES TO TERMINALS 6. OPTIONAL REMOTE SPEAKER/MIC CONNECTIONS VB-4B VOICE BOARD VB-4B TERMINAL BLOCK EXTERNAL MICROPHONE (+) MICROPHONE COMMON (-) MICROPHONE (+) USE SHIELDED TWISTED PAIR WIRE FOR MICROPHONE NOTE: REMOVE JUMPER WHEN USING AN EXTERNAL SPKR REMOVE JUMPER WIRE NOTE: NOT TESTED BY UL TERMINAL BLOCK 5 - DIALER POWER 4 - RELAY NORMALLY OPEN - RELAY COMMON DIALER COMMON - EXTERNAL SPEAKER - EXTERNAL SPEAKER SPKR ROUTE CABLE UNDER STRAIN-RELIEF CLAMP SPKR MIC (-) MIC (+) RSM- TERMINAL BLOCK LINEAR MODEL RSM- RSM- TERMINALS 7. BACKUP BATTERY 8. INSTALL TRANSFORMER TURN POWER SWITCH OFF CONNECT RED LEAD TO POSITIVE AND BLACK LEAD TO NEGATIVE BATTERY TERMINAL PLUG TRANSFORMER INTO AN UN-SWITCHED 7 VAC OUTLET ON OFF BATTERY TYPE: -VOLT,. AMP/HOUR FIT BATTERY INTO SLIDE DOWN SECURE TRANSFORMER WITH SCREW THEN BACK
9. APPLY POWER - SELECT DIALING METHOD TURN POWER SWITCH ON ON 0. TRANSMITTER INSTALLATION OPTIONS FOR ALL TWO-BUTTON TRANSMITTERS WHEN IT IS INSTALLED WITH THE LEFT BUTTON IT WILL ACTIVATE USING EITHER BUTTON WHEN IT IS INSTALLED WITH THE RIGHT BUTTON IT WILL ONLY ACTIVATE USING BOTH BUTTONS NOTE: THE DEFAULT DIALING METHOD IS TONE DIALING IF REQUIRED, CHANGE THE DIALING METHOD BY PRESSING AND HOLDING THE HOME & CLEAR BUTTONS WHILE SWITCHING THE POWER ON FOR DXS- STATIONARY TRANSMITTERS WHEN IT IS INSTALLED WITH THE JUMPER SET FOR DELAY WHEN IT IS INSTALLED WITH THE JUMPER SET FOR INSTANT IT WILL FUNCTION AS IT WILL FUNCTION AS ACTIVITY 7 BEEPS SOUND FOR PULSE DIALING 8 BEEPS SOUND FOR TONE DIALING FOR MODEL DXS-: CUT JUMPER (INSTANT TX) FOR USE AS AN ACTIVITY TX. SEE DXS- INSTALLATION INSTRUCTIONS. INSTALLING SINGLE TRANSMITTERS ADDS ONE TRANSMITTER AT A TIME. INSTALLING MULTIPLE TRANSMITTERS ADDS MULTIPLE TRANSMITTERS PRESS CLEAR BUTTON FOR 5 SECONDS 5 BEEPS SOUND (TX ADD MODE) PRESS TEST BUTTON 4 BEEPS SOUND (TEST MODE) ACTIVATE TRANSMITTER BEEP SOUNDS (TX ADDED) REVERTS TO OPERATE MODE NOTE: IF THE 'S MEMORY IS FULL, ONE LONG BEEP SOUNDS WHEN TRYING TO ADD A TRANSMITTER DXS-6A REPEAT STEPS & FOR ADDITIONAL TRANSMITTERS (UP TO 6 TOTAL) NOTE: PRESS CLEAR BEFORE TRANSMITTING TO RETURN TO OPERATE MODE WITHOUT ENTERING A TRANSMITTER BEEPS SOUND WITH ACTIVITY TIMER ENABLED BEEPS SOUND WITH ACTIVITY TIMER DISABLED THE WILL RETURN TO OPERATE MODE AUTOMATICALLY AFTER 0 SECONDS NOTE: WRITE DOWN EACH TRANSMITTER'S TYPE AND ZONE NUMBER WHEN THE TRANSMITTER IS ADDED. THE CENTRAL STATION WILL NEED TO KNOW THE TYPE AND REPORTING ZONE FOR EACH TRANSMITTER. PRESS TEST BUTTON AGAIN 5 BEEPS SOUND (ADD TX MODE) NOTE: EACH TIME THE TEST BUTTON IS PRESSED IN THE ADD TX MODE, THE WILL BE READY TO INSTALL A TRANSMITTER IN THE NEXT AVAILABLE SENSOR ZONE LOCATION. IF THE VB-4B VOICE BOARD IS INSTALLED, THE WILL ANNOUNCE THE SENSOR ZONE LOCATION NUMBER. ACTIVATE TRANSMITTER BEEP SOUNDS (TX ADDED) NOTE: IF THE 'S MEMORY IS FULL, ONE LONG BEEP SOUNDS WHEN TRYING TO ADD A TRANSMITTER 4 REPEAT STEPS & FOR ADDITIONAL TRANSMITTERS (UP TO 6 TOTAL) DXS-6A 5 PRESS CLEAR TO RETURN TO OPERATE MODE BEEPS SOUND WITH ACTIVITY TIMER ENABLED BEEPS SOUND WITH ACTIVITY TIMER DISABLED THE WILL RETURN TO OPERATE MODE AUTOMATICALLY AFTER MINUTES NOTE: WRITE DOWN EACH TRANSMITTER'S TYPE AND ZONE NUMBER WHEN THE TRANSMITTER IS ADDED. THE CENTRAL STATION WILL NEED TO KNOW THE TYPE AND REPORTING ZONE FOR EACH TRANSMITTER
. TESTING TRANSMITTERS PRESS TEST BUTTON 4 BEEPS SOUND (TEST MODE) 4. ERASING TRANSMITTERS CAUTION: ALL TRANSMITTERS WILL BE ERASED! ACTIVATE EACH OF THE 'S TRANSMITTERS, ONE AT A TIME PRESS AND HOLD TEST BUTTON FOR 5 SECONDS 6 BEEPS SOUND (ALL TRANSMITTERS WERE ERASED) COUNT THE NUMBER OF BEEPS THAT THE SOUNDS WHEN THE TRANSMITTER IS ACTIVATED -BEEP = TX OK -BEEPS = TX HAD ALARM -BEEPS = TX MISSED STATUS 4-BEEPS = TX HAS LOW BATTERY NOTE: WITH THE MODEL VB-4B VOICE BOARD INSTALLED, THE WILL ANNOUNCE THE TRANSMITTER STATUS 4 PRESS CLEAR TO RETURN TO OPERATE MODE BEEPS SOUND WITH ACTIVITY TIMER ENABLED BEEPS SOUND WITH ACTIVITY TIMER DISABLED THE WILL RETURN TO OPERATE MODE AUTOMATICALLY AFTER MINUTES PRESS CLEAR TO RETURN TO OPERATE MODE BEEPS SOUND WITH ACTIVITY TIMER ENABLED BEEPS SOUND WITH ACTIVITY TIMER DISABLED THE WILL RETURN TO OPERATE MODE AUTOMATICALLY AFTER MINUTES 5. LOCAL PROGRAMMING WITH RA-400 PERFORM THE STEPS DETAILED IN THE RA-400/PERS-400 REFERENCE GUIDE (P/N 76) TO SET UP THE RA-400 PROGRAM 6. TELEPHONE CONNECTIONS LOCAL TELEPHONE TELEPHONE JACK TO LOCALLY PROGRAM THE, CONNECT THE MODEM'S LINE JACK TO THE 'S LINE JACK LINE-TO-LINE PRESS TEST BUTTON MOMENTARILY 4 BEEPS SOUND (TEST MODE) NOTE: WILL EXIT TEST MODE AUTOMATICALLY AFTER MINUTES OR BY PRESSING THE CLEAR BUTTON WITH REAR COVER INSTALLED 4 WHEN RA-400 CONNECTION TIMER STARTS COUNTING DOWN, PRESS THE BUTTON 4 BEEPS SOUND (RA-400 ANSWER) ROUTE CABLES UNDER STRAIN-RELIEF TABS 4 5 PERFORM PROGRAMMING IN THE RA-400 SOFTWARE, THEN DISCONNECT FROM THE CONNECT LOCAL TELEPHONE TO THIS JACK CONNECT TELEPHONE LINE TO THIS JACK
7. SYSTEM OPERATION 8. ACTIVITY TIMER POWER LIGHT IS ON OTHER LIGHTS ARE OFF STANDING BY ENABLING THE ACTIVITY TIMER PRESS THE HOME BUTTON FOR 5 SECONDS TO TURN THE ACTIVITY TIMER ON NOTE: THE ACTIVITY TIMER CAN BE ENABLED FOR 8,, OR 4 HOURS, OR DISABLED BY PROGRAMMING NOTE: TO TURN THE ACTIVITY TIMER OFF, PRESS THE HOME BUTTON FOR FIVE SECONDS PRESS AND MOMENTIARLY HOLD BUTTON - IN CASE OF - - OR - ACTIVATE TRANSMITTER PRESS TRANSMITTER BUTTON FOR AT LEAST SECONDS ACTIVITY TIMER RUNNING THE HOME INDICATOR WILL LIGHT, SHOWING THAT THE ACTIVITY TIMER IS ENABLED TIME RUNNING OUT THE HOME INDICATOR WILL BLINK & A SHORT BEEP SOUNDS EVERY 0 SECONDS WHEN LESS THAN 5 MINUTES OF TIME REMAIN SENDING LIGHT FLASHES DURING COMMUNICATION IN ALARM 9. AUDIO BOARD OPERATION SIREN SOUNDS UNTIL CLEAR BUTTON IS PRESSED, CENTRAL STATION REPORT IS COMPLETE, OR SIREN TIME EXPIRES PRESS CLEAR TO STOP SIREN (ADDS CANCEL TO ALARM REPORT IN PROGRESS) 4 RESETING ACTIVITY TIMER THE SUBSCRIBER NEEDS TO PRESS THE HOME BUTTON OR TRIGGER AN ACTIVITY TRANSMITTER BEFORE THE TIMER EXPIRES TO PREVENT AN INACTIVITY REPORT PRESSING THE HOME BUTTON RESTARTS THE TIMER 0. SPEAKERPHONE OPERATION PROGRAM THE TO ENABLE SPEAKERPHONE MODE NOTE: SPEAKERPHONE MODE CAN ONLY BE USED ON INCOMING CALLS AND WILL NOT FUNCTION WHEN THE IS OPERATING FROM BACKUP BATTERY POWER. ATTEMPTING TO ANSWER WHILE THE IS ON BACKUP POWER WILL CAUSE AN ALARM. WHILE THE TELEPHONE IS RINGING, ACTIVATING AN TRANSMITTER OR PRESSING THE BUTTON WILL SEIZE THE TELEPHONE LINE CENTRAL STATION OPERATOR: 4 THE AUDIO BOARD WILL BEGIN -WAY FULL DUPLEX MODE FOR AUDIO COMMUNICATIONS WARNING: THE WILL NOT BE ABLE TO REPORT AN WHILE THE SPEAKERPHONE MODE IS ACTIVE NOTE: TO REPORT AN WHEN THE SPEAKERPHONE IS IN USE, PRESS EITHER THE BUTTON OR THE BUTTON ON AN TRANSMITTER TO END THE PHONE CALL AND THEN PRESS ONE OF THESE BUTTONS AGAIN TO REPORT THE. THE AUDIO BOARD WILL END AUDIO COMMUNICATIONS WHEN EITHER: PRESSING ANY KEY OTHER THAN "9" WILL EXTEND THE AUDIO TIME 90 MORE SECONDS NOTE: TO USE THE AUDIO MODES, THE MODEL VB-4B AUDIO MODULE MUST BE INSTALLED IN THE THE BUTTON IS PRESSED ANY TRANSMITTER IS ACTIVATED THE AUTO-DISCONNECT TIMER RUNS OUT NOTE: TO USE THE SPEAKERPHONE MODE, THE MODEL VB-4B AUDIO MODULE MUST BE INSTALLED IN THE 5
. SUPERVISORY CONDITIONS TRANSMITTER LOW BATTERY TROUBLE WHEN A TRANSMITTER SENDS A LOW BATTERY SIGNAL THE 'S TROUBLE INDICATOR WILL BLINK SLOWLY. TRANSMITTER SUPERVISORY TROUBLE IF A TRANSMITTER PROGRAMMED AS SUPERVISED FAILS TO REPORT STATUS IN A 4 HOUR PERIOD, THE 'S TROUBLE INDICATOR WILL LIGHT. BACKUP BATTERY TROUBLE THE WILL TEST ITS BACKUP BATTERY EVERY 8 HOURS. IF THE BATTERY TESTS LOW, THE POWER INDICATOR WILL BLINK SLOWLY WHILE THE CHARGES THE BATTERY. WHEN TROUBLE EXISTS, THE WILL BEEP EVERY HOUR UNTIL CLEARED: -BEEPS = LOW BATTERY -BEEPS = TRANSMITTER SUPERVISORY 4-BEEPS = TRANSMITTER LOW BATTERY. WIRELESS INSTALLATION TIPS WALLBOARD AND WOOD STUDS 90% - 00% OF FULL POWER LIGHT CONCRETE OR BRICK 65% - 95% OF FULL POWER CONSTRUCTION MATERIALS WILL AFFECT RADIO RANGE CONCRETE WITH STEEL REINFORCEMENT OR METAL LATH AND PLASTER 0% - 70% OF FULL POWER THE WILL REPORT TROUBLE AND/OR 0-DAY STATUS TO THE CENTRAL STATION IF ENABLED IN THE COMMUNICATOR PROGRAMMING CLEARING TROUBLE INDICATIONS PRESS THE CLEAR BUTTON TO STOP TROUBLE INDICATORS AND SOUNDERS NOTE: THE WILL ANNOUNCE THE SUPERVISORY CONDITIONS WITH THE OPTIONAL MODEL VB-4B VOICE BOARD INSTALLED. THE VOICE CAN BE DISABLED THROUGH PROGRAMMING NOTE: THE TROUBLE CONDITION WILL LIKELY OCCUR AGAIN UNTIL THE PROBLEM IS FIXED LOCATION WILL AFFECT RADIO RANGE CENTRALLY LOCATE TRANSMITTERS AT THE OTHER END OF THE HOUSE MIGHT BE TOO FAR AWAY RIGHT WRONG! SPECIFICATIONS CODING FORMATS DX CODE 4-BIT AD PPM,048,567 CODES DXS CODE 4-BIT AD PPM,048,567 CODES POWER REQUIREMENTS PRIMARY SUPPLY 6 VAC.5 AMP PLUG-IN TRANSFORMER BACKUP SUPPLY VOLT. AMP/HOUR BATTERY NORMAL OPERATING CURRENT 80 ma ALARM OPERATING CURRENT 0 ma BACKUP OPERATION DURATION HOURS MINIMUM BATTERY LIFE EXPECTED YEARS BACKUP SUPPLY OPERATING CURRENT ma RF CHARACTERISTICS RECEIVER TYPE DUAL-DIVERSITY SUPERHETERODYNE RF SENSITIVITY -00 dbm TYPICAL RADIO FREQUENCY 5 Mhz MAXIMUM RANGE 400 FEET LINE-OF-SIGHT, OPEN RANGE UL LISTED FOR 50 COMMUNICATOR COMMUNICATOR FORMATS 4 BY (GENERAL OR POINT-TO-POINT), ADEMCO CONTACT ID UL TESTED WITH SURGARD SGMLRG-DG CENTRAL STATION RECEIVER DIALING TONE OR PULSE DIALING DELAY 0 OR 5 SECONDS REMOTE ACCESS PASSWORD 6 DIGITS NOTE: THE INSTALLER MUST ACCOUNT NUMBER LENGTH 4 DIGITS VERIFY COMPATIBILITY PRIMARY TELEPHONE NUMBER 0 DIGITS BETWEEN THE PERS-400B AND SECONDARY TELEPHONE NUMBER 0 DIGITS THE UL LISTED DIGITAL ALARM SUPERVISORY TELEPHONE NUMBER 0 DIGITS COMMUNICATOR RECEIVER STATUS REPORT OPTIONAL, 7 OR 0 DAY REPORT OPERATING TEMPERATURE -00 F (0-50 C) ALARM DURATION -0 MINUTES ACTIVITY TIMER PERIOD 8,, OR 4 HOURS AUDIO LISTEN-ONLY, -WAY MANUAL, -WAY DUPLEX, SPEAKERPHONE RELAY OUTPUT N.O. @ 4 VOLT AC/DC AMP MAXIMUM, NEC CLASS II CIRCUITRY Copyright 008 Linear LLC LINEAR LIMITED WARRANTY This Linear product is warranted against defects in material and workmanship for twelve () months. This warranty extends only to wholesale customers who buy direct from Linear or through Linear s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer s warranty, if any. There are no obligations or liabilities on the part of Linear LLC for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fi tness, are valid only until the warranty expires. This Linear LLC Warranty is in lieu of all other warranties express or implied. All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at -800-4-587 for an RPA# and other important details. IMPORTANT WIRELESS INFORMATION Linear radio controls provide a reliable communications link and fi ll an important need in portable wireless signaling. However, there are some limitations which must be observed. For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 5 devices. As such, they have limited transmitter power and therefore limited range. A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. Changes or modifi cations to the device may void FCC compliance. Infrequently used radio links should be tested regularly to protect against undetected interference or fault. A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users. 879 B