OPERATING INSTRUCTIONS
CONTENTS 1 Runtastic Speed & Cadence Sensor incl. lithium battery (3V, CR2032, Item no. RUNSCS1, type: BSCBLE) 4 tools for assembly SPOKE SPOKE MAGNET PEDAL MAGNET RUBBER CLAMP CABLE TIE Page 2 of 16
ELECTROMAGNETIC COMPATIBILITY Very strong magnetic fields (e.g. transformers) should be avoided, since they may cause distortions of the transmission signals. Noncompliance with this information may lead to defects in or damage to your Runtastic Speed & Cadence Sensor. RISKS FOR CHILDREN AND PEOPLE IN NEED OF CARE This device is not intended for use by children under 8 years or persons with limited physical, sensory, or mental skills or lack of experience and/or insufficient knowledge, unless they are supervised by a person responsible for their safety and well-being or receive instructions from this person on how to operate the device. Children must not play with the device. Cleaning and maintenance operations must not be executed by children unless under supervision. Page 3 of 16
BATTERY OPERATION Your Runtastic Speed & Cadence Sensor uses a lithium battery (3V, CR2032). Here is some information about handling of batteries: Only replace a battery with a battery of equal rating and quality. Batteries must not be charged or reactivated by any other means; they must not be opened, thrown into a fire or short-circuited. Always store batteries out of the reach of children. If swallowed, batteries may be fatal. Store the batteries and the Runtastic Speed & Cadence Sensor out of reach of babies and toddlers. If a battery has been swallowed, immediately seek medical attention. Never expose the batteries to excessive heat, such as solar radiation, fire, etc. This can increase the risk of leakage. Non- Page 4 of 16
compliance with this information may lead to damage and, under certain circumstances, even explosion of the batteries. Promptly remove an empty battery from the Runtastic Speed & Cadence Sensor. Otherwise, it runs the risk of leaking. If a battery is leaking, avoid contact with your skin, eyes, and mucus. Immediately rinse all parts of your body that came into contact with battery acid using plenty of clean water and seek medical attention. If required, clean the battery contacts and mating contacts in the device. Keep the instruction manual in a safe place to be able to look up information, including battery information. Non-compliance with these notes may lead to damage and, under certain circumstances, even explosion of the batteries. For information about replacement of the battery for the Runtastic Speed & Cadence Sensor read the section "Battery Page 5 of 16
replacement in the Runtastic Speed & Cadence Sensor". DISPOSAL Batteries are classified as hazardous waste. For correct disposal of batteries, suitable containers are provided in battery-selling shops and at municipal waste collection points. If you want to dispose of your Runtastic Speed & Cadence Sensor, please comply with the currently valid local rules and regulations. Obtain information from the competent municipal body. KRIPPL-WATCHES Warenhandels GmbH Maria-Theresia-Straße 41, 4600 Wels, Austria Dispose of packaging in compliance with currently valid rules and regulations. Obtain information from the competent local municipal body. Page 6 of 16
FUNCTIONS AND USE For transmission of cycling speed and cadence from your Runtastic Speed & Cadence Sensor to your smartphone, the latest Bluetooth technology is used. I.e. smartphones with Bluetooth Smart and Bluetooth Smart ready are compatible. An up-to-date list of all compatible smartphones is provided at www.runtastic.com/products Page 7 of 16
GETTING STARTED 1. Installation of Runtastic Bike App and activation code Copy the link provided below into the address bar of your browser to open Runtastic.com; there you can get step-by-step help and instructions for entering your activation code. http://www.runtastic.com/activate Or scan the QR code below using your smartphone to open the page. In order to be able to use this feature, you need to have previously downloaded the free app from the corresponding store, and then you can scan these types of codes. Now, scan the QR code and follow the instructions on Runtastic.com. In order to use your Runtastic Speed & Cadence Sensor you must Page 8 of 16
activate your Bluetooth interface and the sensors in the Bike App. 2. Connecting the Speed & Cadence Sensor to your smartphone Open the Runtastic Bike App and access the Settings screen. Then choose Sensors and then Sensors again. Now choose the third option Bluetooth Smart. To activate your Speed & Cadence Sensor take either the spoke or the pedal magnet and move it across the corresponding marks on the Speed & Cadence Sensor, with a maximum distance of 4 5 mm between sensor and magnet. Once successfully activated the color of the symbols for speed and cadence on the display of your Page 9 of 16
smartphone will change from orange to green. If the activation has not been successful, choose Unpair all sensors and repeat the activation process. In addition, you can deactivate and then reactivate the Bluetooth signal in your phone settings. 3. Assembly of the Runtastic Speed & Cadence Sensor 1. We recommend attaching the Runtastic Speed & Cadence Sensor to the chain stay of your bike (see figure below). 2. Guide the cable ties through the openings in your Runtastic Speed & Cadence Sensor. Mount the sensor to the chain stay so that the Runtastic logo faces out- Page 10 of 16
ward. Close the cable ties, but do not tighten them firmly yet. 3. Position the spoke magnet on one of the spokes so that the magnet is level with the Runtastic Speed & Cadence Sensor. Mount the spoke magnet on the spoke and close the cable ties, but do not tighten them firmly yet. In order to be able to mount the pedal magnet in the correct position, the pedal must first be disassembled. Then, position the pedal magnet so that it is level with the Runtastic Speed & Cadence Sensor. Page 11 of 16
Then mount the pedal onto the crank arm. Adjust the position of the spoke magnet so the magnet passes very close to the sensor but does not touch it. Keep a maximum distance of 4 5 mm between the magnet and the Runtastic Speed & Cadence Sensor. Align the Runtastic Speed & Cadence Sensor towards the wheel / spokes as precisely as possible. Note: The Speed & Cadence Sensor is composed of two parts. To ensure optimal assembly on your bicycle slightly loosen the screws with an Allen key. Now you can adjust the two parts for Page 12 of 16
ideal positioning. When finished tighten the screws again. NOTE: The speed and cadence measurement must only be activated once, before the first training session, after deactivation of the Bluetooth interface, after clicking the Unpair all sensors button and/or upon replacement of the battery or the Runtastic Speed & Cadence Sensor. STORAGE Do not expose the Runtastic Speed & Cadence Sensor to excessive solar radiation over a longer period. Page 13 of 16
BATTERY REPLACEMENT IN THE Runtastic SPEED & CADENCE SEN- SOR Open the battery compartment cover with a coin by turning it counterclockwise. Remove the old battery and insert a new 3V battery (type CR2032). Always ensure that the positive pole (+) is facing upwards. Refit the battery cover and lock it by turning it clockwise. Ensure that the cover is securely closed, to prevent moisture from entering the Runtastic Speed & Cadence Sensor. SPECIFICATIONS Runtastic Speed & Cadence Sensor Power supply: 1 lithium battery (3V 0.5 ma CR2032) Transmission frequency from Runtastic Speed & Cadence Sensor to smartphone: Bluetooth 4.0 Page 14 of 16
Water tightness The Runtastic Speed & Cadence Sensor is splash-proof. DECLARATION OF CONFORMITY EC R&TTE Directive 1999/05/EC: Short text of the declaration of conformity: Krippl-Watches hereby declares that the Runtastic Speed & Cadence Sensor (item no. RUNSCS1, type: BSCBLE) conforms to the fundamental requirements and other relevant provisions of directive 1999/05/EC. The full text of the declaration of conformity can be viewed on our website: www.runtastic.com WARRANTY We offer a 24-month warranty for this product. The warranty period starts from the date of sale (receipt, proof of purchase). Within this period we repair all defects resulting from material failure or malfunctions free of charge, except: batteries, improper handling, dropping, shock or the like. Page 15 of 16
If you would like to submit a complaint, you have the following options: a) Contact your dealer or b) Write an email to: service@runtastic.com PLEASE NOTE: FOR ORGANIZA- TIONAL REASONS, WE CANNOT AC- CEPT ANY UNANNOUNCED PACK- AGES WHICH HAVE NOT BEEN PRE- PAID. Page 16 of 16 www.runtastic.com