INSTALLATION & USER GUIDE

Transcription

1 IN-WALL SCENE CONTROLLER IWC600 INSTALLATION & USER GUIDE

2 MONSTER ILLUMINESSENCE DESIGNER SERIES PRODUCTS: Dimmable Table & Floor Lamps Plug In Light Station Dimmer ML LD300 ON/OFF Compact Fluorescent Lights & Appliances Plug In Light & Appliance Station Dimmer ML LAS1000 Dimmable Ceiling Lights Table & Floor Lamps InWall Dimmer ML IWD600s ON/OFF Ceiling Fluorescents Table & Floor Lamps InWall Switch ML IWS1000s Controls All or Selected Lights at the Push of a Button InWall Scene Controller ML IWC600

3 INTRODUCTION MONSTER ILLUMINESSENCE : POWERFUL WHOLE HOME LIGHTING CONTROL MADE SIMPLE Monster s IlluminEssence dimmers, switches and controllers communicate with each other via Monster ControlNet, a wireless Radio Frequency (RF) technology that provides whole-house remote control over your home lighting without the need for new wiring or custom installation. Each station in Monster s IlluminEssence lighting component line acts as its own wireless router. These routers transmit the wireless RF signals from one device to another until the intended device is reached and controlled according to the user s preferences. This ensures that the signal is received by its intended device by routing the signal around obstacles and radio dead spots. Thanks to this innovative routing system and wireless RF ControlNet, Monster s IlluminEssence modules can work through floors, walls, ceilings and cabinets. Monster s scene-capable 1

4 dimmer modules are compatible with any Z-wave enabled network, regardless of the manufacturer, and can also be used with other devices displaying the Z-wave logo. WARNINGS AND CAUTIONS: ON/OFF LED shows status of remote load control. To be installed and/or used in accordance with appropriate electrical codes and regulations. If you are unsure about any part of these instructions, consult a qualified electrician. Monster Recommends that you remember to exercise good sense when using any timer features in a remotecontrollable system, especially when scheduling unattended devices. There can be some unexpected consequences if not used with care. For example, an empty coffee pot can be remotely turned on. If that should happen, your coffee pot could be damaged from overheating. If an electric heater is turned on by 2

5 Recommended minimum wall box depth is 2-1/2. Maximum wire lengths fro switch to all installed auxiliary remote switches cannot exceed 300 ft. (90m) for 3-way switch applications. Disconnect power at circuit breaker or fuse when servicing, installing or removing the fixture. Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL. Do not exceed the rated wattage capacity shown on your product packaging. remote control while clothing is draped over it, a fire could result. DO NOT USE the remote for the control of high power heating appliances such as portable heaters. This device will not control lighting that is used with electronic low-voltage and high frequency power supply transformers, nor high pressure discharge lamps (HID lighting). This includes mercury-vapor, sodium vapor and metal halide lamps. 3

6 This device is intended for indoor use only. PREPARE FOR INSTALLATION TOOLS YOU LL NEED TO INSTALL YOUR ILLUMINESCENE SCENE CONTROLLER: Slotted/Phillips Screwdriver Pencil Electrical Tape Pliers Pencil Cutters Ruler FEATURES Store and recall 4 customized lighting scenes without traveler wires ON/OFF LED indicates status of lighting scenes IlluminEssence Real Time Feedback provides ON/OFF status from dimmers/ switches Monster ControlNet reliably works through walls, floors and cabinets 4

7 Simple installation no new wiring Compatible with other Z-Wave enabled devices Ability to Quickly Adjust Lighting Scenes IR Remote Controlled with built in IR receiver allows line of sight control with infrared remotes NOTE: To make the IWC600 capable of responding to infrared (IR) commands, do this: Before mounting the frame, press out the DIM/BRIGHT (bottom) from the back of the frame and press in from the front the new DIM/BRIGHT button, with the IR window into the frame. 5

8 INSTALLING YOUR CONTROLLER STEP 1: WARNING!!: It is important to ensure that all circuit breakers are turned OFF prior to installation! To do this, follow these steps: 1) Find your home circuit breaker panel and turn off the appropriate labeled breakers for the room that you plan to be installing IlluminEssence in-wall scene controller. 2) Return to the room and CONFIRM that the electricity is turned off. 6

9 STEP 2: IDENTIFYING YOUR WIRING: NOTE: This diagram represents a typical single-pole, 2-way wiring configuration. This product will also work in 3-way configurations. Single-Pole 1. Line (Hot) 2. Neutral 3. Ground 4. Load 7

10 STEP 3: PREPARING AND CONNECTING WIRES: This 4-scene controller can be wired using side wire terminal screws, or through the back wire openings. Choose the appropriate wire stripping specifications accordingly. Cut (if necessary) Strip Gage (measure bare wire here) 5/8" (1.6 cm) Side Wire Connection Side wire terminals accept #14 AWG solid copper wire only. Back Wire (either hole may be used) Back wire openings use #14-12 AWG solid copper wire only. Make sure that the ends of the wires from the wall box are straight (cut if necessary). Remove insulation from each wire in the wall box as shown. 8

11 STEP 4: WIRING THE ILLUMINESSENCE SCENE CONTROLLER: Connect the wires shown in the WIRING DIAGRAM as follows: 4-Scene Controller * Green or bare copper wire in wall box to Green terminal screw. Line Hot wall box wire to terminal screw marked BK. Line Neutral wall box wire to terminal screw marked WH. 9

12 STEP 5: TESTING YOUR 4-SCENE CONTROLLER PRIOR TO MOUNTING IN WALL BOX: *Dual Gang Wall Plate Not Included Position all wires to provide room in outlet wall box for device. Ensure that the word TOP is facing up on device strap. Partially screw in mounting screws in wall box mounting holes. NOTE: Dress wires with a bend as shown in diagram in order to relieve stress when mounting device. 10

13 * *Dual Gang Wall Plate Not Included Restore power at circuit breaker or fuse. LED should turn ON. If LED does not turn ON, refer to the TROUBLESHOOTING section. 11

14 STEP 6: PAIRING YOUR ILLUMINESSENCE IN-WALL 4-SCENE CONTROLLER INTO THE NETWORK NOTE: Only one device may be paired at a time. DO NOT put multiple devices into the Pairing mode at any time. A) Follow the instructions on your Monster Controller/Programmer to pair a Monster IlluminEssence or other Z-Wave-enabled lighting station into the lighting network. When it s ready to pair a new device, proceed to Step B. B) While standing close to the IlluminEssence 4-scene controller (approximately 2-5 ft.) with the Monster IlluminEssence lighting modules use a wireless technology called Monster ControlNet that brings your home lighting fixtures into a simplified network. In order for the network to properly recognize each lighting source, each light must be included or paired to the network. 12

15 Monster programmer/controller in hand, press the center button on the 4-scene controller to pair it in the network. C) Your Monster Programmer/Controller will assign a node ID number (a name) for the 4-scene controller. This ID number (Name) will be stored in the This process is necessary for each lighting device you want to add to the network, and you only need to do it once. When you want to remove a light from your lighting network, you exclude or remove that light, so that the network doesn t need to recognize it anymore. 13

16 Monster Programmer/ Controller to be used for future reference. You can name or edit the 4-scene controller for easy reference, such as downstairs or living room, etc. D) The IlluminEssence 4-scene controller is now installed in the network. E) Once paired into the network, the 4-scene controller must be updated to allow it to be associated with all devices in your home network. Follow the instructions on your Monster Programmer/Controller to update the network status, including your 4-scene controller (See Step 8). NOTE: You only pair a lighting station into the network once. If the switch has already been successfully Paired in the network and you try to Pair it again without first removing it from the network, the network will assume there are two switches. 14

17 STEP 7: REMOVING/EXCLUDING AN ILLUMINESSENCE IN-WALL 4 SCENE CONTROLLER FROM THE NETWORK A) Follow the instructions on your Monster Controller/Programmer to remove a Monster IlluminEssence or other Z-Wave-enabled lighting station from the lighting network. When it s ready to remove the device that you want removed, proceed to Step B. B) While standing close to the switch (approximately 2-5 ft.) with the Monster programmer/controller in hand, press the center button on the 4-scene controller to remove it from the network. When you want to remove a light from your Monster ControlNet system or any wireless Z-Wave network, it is very important to accurately exclude it from the network This ensures that all information has been removed from your Primary Programmer/Controller s information and that unwanted lights are not counted on to be part of the network. 15

18 Factory Default: If your 4-scene controllers not responding, or you are unable to control it after you have tried to Pair or Remove it multiple times, it may be necessary to reset the 4-scene controller to its original factory settings. To do this, proceed as follows: On the 4-scene controller, (refer to figure). Wait 5 seconds and then press the push pad back into the frame and hold push pad until the locator LED flashes Amber and turns solid Red. The 4-scene controller is now reset. Once the controller is reset, it will be necessary to Re-Pair it to a network before it can be used. 16

19 CAUTION: SETTING A DEVICE TO A FACTORY DEFAULT DOES NOT REMOVE THAT DEVICE FROM A NETWORK. THE REMOVAL/EXCLUSION PROCEDURE MUST STILL BE FOLLOWED TO REMOVE THE DEVICE FROM THE PRIMARY CONTROLLER S INFORMATION TABLE. FAILURE TO DO SO MAY RESULT IN SYSTEM THAT IS SLOW TO RESPOND, OR MAY FAIL TO RESPOND TO SOME DEVICES. STEP 8: LIGHT STATION ASSOCIATION After the Pairing process, you must associate the IlluminEssencecontrolled devices to the Monster ControlNet. Refer to your Monster Programmer/Controller instruction sheet for complete details. NOTE: One Monster IlluminEssence light station can be associated to multiple controllers (up to five (5) controllers maximum). 17

20 Once association is complete, you can set a scene as follows: Press and hold button on the 4-Scene Controller until the LED blinks Green. Adjust the lighting devices that you want to add to the scene. Press button again on 4-Scene Controller and the LED will stop blinking. The scene has now been set. STEP 9: MOUNTING THE ILLUMINES- SENCE 4-SCENE IN-WALL CONTROLLER TURN OFF POWER AT THE CIRCUIT BREAKER OR FUSE! STEP 10: RESTORE POWER: Restore the power at your circuit breaker or fuse. The installation is now complete. 18

21 OPERATION Push Button Default Settings: Turning Scenes ON from the OFF position: Press the appropriate scene button; the scene LED will light up. The LED will blink until the scene is portrayed. Turning Scenes OFF from the ON position: Press the appropriate scene button; the scene LED will go off. All lights in the scene will go off. 19

22 NOTE: While LED is blinking, a button press will be ignored. NOTE: The LED will be lit only when all lights in a scene have reached their preset level. If there is a manual change to any light in the scene, the LED will turn OFF indicating that you are no longer in that scene. If there is a power outage, when the power is restored, the lights will return to the last setting before the power interruption. Cleaning: Clean with a damp cloth. DO NOT use chemical cleaners. 20

23 TROUBLESHOOTING PROBLEM: LIGHTS FLICKERING The lamp has a bad connection. The wires are not secured firmly under terminal screws of 4-scene controller and/or remote. PROBLEM: LIGHT DOES NOT TURN ON AND LOCATOR LED DOES NOT TURN ON The circuit breaker or fuse has tripped. The lamp is burned out or lamp switch is OFF. The lamp Neutral connection is not wired. If the 4-scene controller is powered up and LED does not turn ON, check the wiring. If no lights react to a button press, then the association of devices was not done properly. Consult the instructions for your Monster Programmer/Controller. 21

24 PROBLEM: IWC600 DOES NOT OPERATE LIGHTS Check that all IlluminEssence/MCC controllers and light stations have been properly associated. Ensure that the IWC600 was properly updated. 22

25 FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving Antenna. Increase the separation between the equipment and the receiver. 23

26 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. LIMITED WARRANTY FOR CONSUMERS Monster, LLC, 7251 West Lake Mead Blvd., Suite 342, Las Vegas, NV 89128, USA, (415) ( Monster ) extends You this Limited Warranty. Statutory or common law may provide You with additional rights or remedies, which shall not be affected by this Limited Warranty. DEFINITIONS Adequate Use means use of the Product (i) within a home or dwelling, (ii) for private (as opposed to commercial) purposes, (iii) in conformance with all applicable local, state or federal law, code or regulations (including without limitation building and/or electrical codes), (iv) in accordance with manufacturer recommendations and/or instructions in the materials and documentation that accompany the Product, and (v) with proper electrical grounding. 24

27 Authorized Dealer means any distributor, reseller or retailer that (i) was duly authorized to do business in the jurisdiction where it sold the Product to You, (ii) was permitted to sell You the Product under the laws of the jurisdiction where You bought the Product, and (iii) sold You the Product new and in its original packaging. Formal Warranty Claim means a claim made in accordance with the section Formal Warranty Claims herein. Product means a Product (i) that is listed in the Specifications Table below, (ii) that You bought from an Authorized Dealer new and in its original packaging, and (iii) whose serial number, if any, has not been removed, altered, or defaced. Product Defect means an inadequacy of the Product that existed at the time when You received the Product from an Authorized Dealer and that causes a failure of the Product to perform in accordance with Monster s documentation accompanying the Product, unless such failure has been caused completely or partly by (a) any use other than Adequate Use, (b) transportation, neglect, misuse or abuse by anyone other than Monster s employees; (c) alteration, tampering or modification of the product by anyone other than a Monster employee; (d) accident (other than a malfunction that would otherwise qualify as a Product Defect); (e) maintenance 25

28 or service of the Product by anyone other than a Monster employee; (f) exposure of the Product to heat, bright light, sun, liquids, sand or other contaminants; or (g) acts outside the control of Monster, including without limitation acts of God, fire, storms, earthquake or flood. Warranty Period means the time period during which Monster must have received Your Formal Warranty Claim. The different Warranty Periods related to Product Defects are defined in the Specifications Table below. The Warranty Period commences on the date when You purchased or received (whichever occurs later) the Product from an Authorized Dealer as evidenced by the Authorized Dealer s invoice, sales receipt or packing slip. If You do not have written proof of the date of purchase or receipt, then the Warranty Period commences three (3) months after the date when the Product left Monster s or its factory as evidenced by Monster s records. The Warranty Period ends after the time defined in the Specifications Table has expired or after You have transferred ownership of the Product, whichever occurs earlier. Also, You must call Monster and obtain a Return Authorization Number (as described under How to Make a Claim ) within two (2) months after You discover a Product Defect (or should have discovered it, if such Product Defect was obvious). You means the first individual person that purchased the Product in its original 26

29 packaging from an Authorized Dealer. This Limited Warranty does not apply to persons or entities that bought the Product (i) in used or unpackaged form, (ii) for resale, lease or other commercial use, or (iii) from someone other than an Authorized Dealer. SCOPE OF THIS LIMITED WARRANTY PRODUCTS. If a Product contained a Product Defect when You bought it from an Authorized Dealer and Monster receives a Formal Warranty Claim from You within two (2) months after You discover such Product Defect (or should have discovered it, if such Product Defect was obvious) and before the end of the Warranty Period for Product Defects applicable to the affected Product, then Monster will provide You with one of the following remedies: Monster will (1) repair or, at Monster s sole discretion, replace the Product, or (2) refund to You the purchase price You paid to the Authorized Dealer for the affected Product if repair or replacement is not commercially practicable or cannot be timely made. NOTE: MONSTER DOES NOT ASSUME ANY LIABILITY FOR ANY INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES UNDER THIS LIMITED WARRANTY. GENERAL PROVISIONS CHOICE OF LAW/JURISDICTION. This Limited Warranty and any disputes 27

30 arising out of or in connection with this Limited Warranty ( Disputes ) shall be governed by the laws of the State of California, USA, excluding conflicts of law principles and excluding the Convention for the International Sale of Goods. The courts located in the State of California, USA shall have exclusive jurisdiction over any Disputes. OTHER RIGHTS. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE AND JURISDICTION TO JURISDICTION, AND WHICH SHALL NOT BE AFFECTED BY THIS LIMITED WARRANTY. THIS WARRANTY EXTENDS ONLY TO YOU AND CANNOT BE TRANSFERRED OR ASSIGNED. If any provision of this Limited Warranty is unlawful, void or unenforceable, that provision shall be deemed severable and shall not affect any remaining provisions. In case of any inconsistency between the English and other versions of this Limited Warranty, the English version shall prevail. REGISTRATION. Please register Your Product at Failure to register will not diminish Your warranty rights. 28

31 SPECIFICATIONS TABLE Product Model ML IWC600 Warranty Period for Product Three (3) Years FORMAL WARRANTY CLAIM HOW TO MAKE A CLAIM. In the event damage has occurred to Products, You must follow these instructions: (1) Call Monster within two (2) months after You discover a Product Defect (or should have discovered it, if such Product Defect was obvious); (2) Give a detailed explanation of how the damage occurred; (3) Obtain a Return Authorization Number; (4) Upon receipt of a claim form (which may be sent to You after You filed Your Formal Warranty Claim), fill out the claim form entirely; (5) Return the Products, shipping prepaid by You (to be refunded if You are entitled to a remedy under the Scope of this Limited Warranty), to Monster for verification of damage, along with a copy of Your original sales receipts and proof of purchase (UPC label or packing slip) for such Products, the completed claim form, and printed Return Authorization Number on the outside of the return package (the claim form will include instructions for return). 29

32 TELEPHONE NUMBERS. United States, Asia Pacific and Latin America: or , Canada , Czech Republic , UK , Germany , France , Netherlands , Belgium , Norway , Denmark , Sweden , Finland FURTHER PROCEEDINGS. Monster will determine whether a Product Defect existed. Monster may, at its discretion, direct You to obtain a repair estimate at a service center. If a repair estimate is required, You will be instructed on how to properly submit the estimate and the resulting invoice to Monster for payment. Any fees for repairs may be negotiated by Monster. TIMING. If You bring a Formal Warranty Claim and fully comply with all terms and conditions of this Limited Warranty, Monster will use its best efforts to provide You with a remedy within thirty (30) days after receipt of Your Formal Warranty Claim (if You reside in the United States - forty-five (45) days if You reside elsewhere), unless obstacles outside Monster s control delay the process Ver US/EU 2003 Monster, LLC 30

33 NOTES 31

34 NOTES 32

35 NOTES 33

36 MonsterCentral.com 2006 Monster, LLC 7251 West Lake Mead Blvd. Las Vegas, NV 89128, USA Monster Central products are designed in the USA and manufactured for Monster to its quality specifications. Manufactured in China. Monster, Monster Central, the Monster Central logo and the product design, Omnilink, Monster System Tracking Memory, IlluminEssence, ControlNet, are registered or unregistered trademarks of Monster Cable Products, Inc. or its subsidiaries in the US and other countries. rm