the equipment sourcebook volume 6

Transcription

1 the equipment sourcebook 2007 volume 6

2 INTRODUCTION The Equipment Sourcebook Since 97, Henkel Corporation has designed, built, and integrated high quality equipment solutions. From simple hand held devices to fully automated systems, Henkel offers a complete line of standard off- the- shelf Loctite brand dispensing and light curing equipment which can easily be integrated into your manufacturing process. From water thin liquids to high viscosity pastes, Loctite brand equipment is capable of dispensing and curing a wide variety of adhesives, sealants, and other industrial fluids: Adhesives & Sealants Industrial Fluids Acrylics Hot Melts Accelerators/Activators Paints Anaerobics Silicones Greases Primers Cyanoacrylates Urethanes Inks Solvents Epoxies UV/Light Curing Adhesives Lubricants/Oils Solder Pastes In addition to our standard line of equipment, Henkel offers a number of resources to support your dispensing needs: Custom Equipment Systems We can modify any Loctite brand standard system or customize a system to meet your specific assembly needs. Equipment Rental Program Evaluate the performance of our equipment before making a capital investment. Equipment Website Locate details on Loctite brand standard and custom equipment; parts and accessories; and equipment services. To learn more about our equipment, or to find the name and phone number of your nearest authorized distributor, visit Adhesives and Sealants Specialists Henkel Adhesives and Sealants Specialists are available across the continent to personally assist you with new assembly challenges or to help you re-engineer an existing application for improved performance and cost savings using Loctite brand products. Contact us at -800-LOCTITE ( ) or visit The Adhesive Sourcebook 2007, volume 7 In addition to our dispensing and curing equipment, Henkel offers a complete line of adhesives, sealants, cleaners, lubricants, potting compounds, and coatings. Over,400 products in total! To view our on-line catalog, visit or to request a copy, send an to [email protected], and reference the Adhesive Sourcebook, LT Engineering Services Henkel now offers complete engineering services for projects demanding expertise and support beyond the limits of our standard technical services. As a result, our engineers and scientists can quote the following value-added services: On-site engineering assistance and consultation Joint product development programs Contract lab services and testing Prototype testing and fixture preparation Custom formulations For more information on these and other Henkel Engineering Services, contact your Henkel Adhesives and Sealants Specialist at -800-LOCTITE ( ).

3 Table of Contents INTRODUCTION EQUIPMENT SERVICE SOLUTIONS DISPENSING DISPENSE SYSTEMS Loctite Benchtop Peristaltic Dispenser Loctite Bond-A-Matic 3000 Dispenser Loctite Shot Miser Dispense System Loctite Posi-Link Dispense System for Prepackaged Syringes Loctite Precision Syringe Dispensing System Loctite Digital Syringe Dispensing System Loctite Foot Pedal Dispenser Loctite Dial-A-Seal Applicator Loctite Pump-A-Bead II Dispenser Loctite Light Cure Acrylic Adhesive Dispensing System CONTROLLERS AND RESERVOIRS Loctite Single Channel Automatic Controller Loctite Spray Valve Controller Loctite Digital Multi-Functional Controller Loctite Digital Dispense Controller Loctite Shot Miser Valve Controller Loctite Integrated Semi-Automatic Dispenser Loctite Bond-A-Matic 3000 Reservoir Loctite 300 ml Cartridge Pusher Loctite 2.25 Gallon Pressure Reservoir Loctite Shot Miser Reservoir Loctite 4 Liter Gravity Feed Reservoir HAND HELD APPLICATORS Loctite 50 ml / 250 ml Hand Pumps Loctite Liter Collapsible Bottle Holder Loctite Soft Squeeze Bottles Loctite 30 ml Manual Syringe Applicator Loctite 0 ml / 30 ml Syringe Manual Plungers Loctite 50 ml Dual Cartridge Manual Applicator Loctite 50 ml Dual Cartridge Pneumatic Applicator Loctite Caulking Gun Conversion Kits for 50 ml Cartridges Loctite 200 ml / 400 ml Dual Cartridge Manual Applicators Loctite 200 ml / 400 ml Dual Cartridge Pneumatic Applicators Loctite Universal Metal Dispenser Loctite Fixmaster Rapid Rubber Repair Dispenser Loctite 300 ml Pneumatic Cartridge Dispenser Loctite Foldable 300 ml Cartridge Applicator Loctite 300 ml Pneumatic Cartridge Dispenser Retainer.. 29 TWO-PART VOLUMETRIC DISPENSING DUAL CARTRIDGE SYSTEMS Loctite Posi- Link Dispense System for Dual Cartridges TWO-PART VOLUMETRIC DISPENSING METER MIX Loctite DuraPump Programmable Meter Mix System Loctite DuraPump Pneumatic Meter Mix System Loctite Meter Mix 000 Dispense System Loctite Meter Mix 2000 Dispense System Loctite Meter Mix 3000 Dispense System Loctite Meter Mix Dispense Systems Accessory Option Selector Guide Loctite Brand Meter Mix System Options and Accessories Loctite Brand Meter Mix Feed System Options and Accessories for Meter Mix 000, 2000 and 3000 Dispense Systems Loctite Meter Mix Dispensing Systems Pump Selector Guides HAND HELD HOT MELT APPLICATORS Loctite Hysol 050 / 050-HT / 050A Loctite Hysol 050-GAS Loctite Hysol 050-LITE Loctite Hysol 075 / 075-LT Loctite Hysol 75-AIR / 75-AIR-HT Pneumatic Applicators Loctite Hysol 75-SPRAY / 75-SPRAY-HT Pneumatic Applicators Loctite Hysol 75 Manual Applicator Loctite Hysol Reactive Urethane Cartridge Dispenser Loctite Hot Melt Bench Mount Kit Loctite Hot Melt Pneumatic Timer Loctite Hot Melt Nozzles and Accessories BULK HOT MELT SYSTEMS Loctite Hysol PUR Hot Melt 5 Gallon Pail Pump Loctite Hysol Bulk-2 System Loctite Hysol Bulk-4 System Loctite Hysol Bulk-34 System Loctite Hysol Bulk Hot Melt System Applicators Loctite Hysol Bulk Hot Melt System Hoses, Controllers, Timers Loctite Bulk Hot Melt System Nozzles and Accessories HAND HELD VALVES Loctite LV Hand Held Applicator Loctite Manual Hand Held Applicator Loctite Pneumatic Hand Held Applicators Loctite Vari-Drop Applicator Loctite Brand Hand Held Dispensing Valve Fluid Compatibility Chart INTRODUCTION Table of Contents

4 INTRODUCTION Table of Contents VALVES & PUMPS Loctite Stationary Applicator Valve Loctite Micro Needle Valve Loctite Light Cure Dispense Valve Loctite Cyanoacrylate Dispense Valve Loctite Diaphragm Valve Loctite Spray Valve Loctite Spray Valve Controller Loctite Poppet Valves Loctite Stainless Steel Poppet Valve Loctite Shot Miser Dispense Valve Loctite Positive Displacement Pump Loctite Rotospray 9000 Applicator Loctite Brand Valve & Pump Fluid Capability Chart PAIL PUMPS Loctite Low Viscosity Fluid Pumps Loctite High Viscosity Paste Pump Systems Loctite Pail Pump Accessories MONITORING SYSTEMS Loctite Fluorescence Detector Loctite In-Line Flow Monitor Loctite Fluid Waveform Analyzer, Signature Series CONSUMABLES DISPENSE ACCESSORIES Loctite Brand Dispense Tips Loctite Brand Cartridge Accessories Loctite Brand Static Mix Nozzles and Accessories Loctite Brand Syringe Accessories Loctite Brand Dispensing Spare Parts and Accessories MOTION CONTROL ROBOT DISPENSE SYSTEMS Loctite 200 Benchtop Robot Station Loctite 300 Benchtop Robot Station Loctite 400 Benchtop Robot Station Loctite 500 Benchtop Robot Station Loctite S440 Series SCARA-N Robot DISPENSE STATIONS Loctite Advancing Slide Dispense Station Loctite Single Rotary Dispense Station Loctite Dual Rotary Dispense Station Loctite Brand Mounting Hardware, Workbenches, and Guarding Enclosures FUME FILTRATION SYSTEM Benchtop Fume Filtration System O-RING FABRICATION Loctite Precision O- Ring Cut and Splice Tool LIGHT CURE LIGHT CURE SOLUTIONS Loctite 7700 LED Light Source Loctite 7703 LED Light Source Loctite 7700-HD LED Light Source Loctite 7703-HD LED Light Source Loctite CureJet 405 LED Loctite CureJet Indigo LED WAND SYSTEMS Loctite Indigo 7720 Visible Light Wand System Loctite ZETA 7735 UV Wand Systems Loctite ZETA 7740 UV Wand System Loctite ZETA 7760 UV Wand System CURE CHAMBERS & FLOOD SYSTEMS Loctite UVALOC 000 UV Cure Chamber Loctite ZETA 740 UV Chamber Loctite ZETA 74-S UV Flood System Loctite Indigo 748 Visible Light Flood System Loctite ZETA 7420 Visible Light Flood System LIGHT METERS Loctite ZETA 70-A Dosimeter-Radiometer Loctite ZETA 70-V Dosimeter-Radiometer Loctite ZETA 702 Spot Radiometer CURE CONVEYORS Loctite ZETA 745 UV Benchtop Conveyor Loctite ZETA 760 UV Benchtop Conveyor LIGHT SOURCES Loctite Electrodeless Lamp Assembly and Power Supply... 7 Loctite High Intensity Ultraviolet Sources INDEX Item Number Listing

5 As a full service supplier of equipment, Henkel offers a wide variety of Equipment Services to its customers. INTRODUCTION Equipment Service Solutions FACTORY REPAIRS If you have equipment in need of repair, Henkel can restore it to original operating specification. Customers often schedule preventive repairs to coincide with annual shut downs. Henkel can work with you to get your equipment up and running in the fastest possible time frame. Rental equipment may be available on a short term basis to minimize down time. Benefits of Factory Repair Service include: Trained technicians evaluate equipment based on original design specifications to identify critical and preventive repair recommendations Equipment is repaired using original factory parts All equipment is fully tested to original quality specifications All repairs carry a 30 day labor and 90 day parts warranty CALIBRATIONS Henkel provides calibration services for all of its light meters. All meters are calibrated to original calibration standards. Data is collected before and after calibration and a calibration certificate is issued that states test results. In addition, you can sign up with Henkel for calibration reminders. All units are also inspected during calibration for any potential repairs. REBUILD EXCHANGE PROGRAM The Henkel rebuild exchange program offers customers a cost effective way of streamlining the repair of dispensing valves. The rebuild program allows customers to send in their old valve and receive a reconditioned valve in return. Customers who participate in this program typically keep a spare valve in inventory so if a valve goes down it can be replaced immediately. The valve in need of repair is then sent to Henkel and a reconditioned valve is shipped back to the customer for future use. Advantages of the Rebuild Exchange Program are: Rebuilt equipment is less than half the cost of a new unit Rebuilt equipment is shipped in to 2 business days Highly trained technicians use original factory parts All equipment is specially treated with a Henkel patented technology to prolong its useful life with reactive adhesives All rebuilds carry a 30 day labor and 90 day parts warranty FIELD SERVICE Henkel Technicians are available to travel to your location for repair services, preventative maintenance, training or assistance in setting up a new system. Whatever you need, Henkel can provide the service. DISCOUNT EQUIPMENT Henkel is able to offer a wide range of used or discontinued equipment at discounted prices. This equipment typically has been used in our rental program or has been used for customer demonstrations or trade shows. This equipment may have cosmetic blemishes, but performs to original factory specification. All equipment carries the same warranty as new equipment and is fully tested and reconditioned prior to sale. SPARE PARTS Spare parts and accessories are available through the equipment services group of Henkel. Most common spare parts can be identified on our website at If you cannot find the part you are looking for, our equipment services group can help you identify that part and provide you with a quote. 3

6 Equipment Service Solutions INTRODUCTION EQUIPMENT RENTAL Many of the equipment products that Henkel offers are available for short term rental. Henkel s equipment rental program allows customers the flexibility to confirm the performance of our adhesive and equipment risk-free before investing in a purchase. If, during the first 30 days, you decide that you would like to purchase the rental equipment, the entire rental charge is credited toward your purchase. The benefits of this program include: The performance of a new manufacturing process can be confirmed before investing fully in the purchase of equipment Short production runs can be accommodated without having to buy equipment Equipment can be rented during the repair of production equipment, minimizing any down time LEASE-TO-OWN PROGRAM Henkel offers a lease- to- own program for new equipment. According to the United States Equipment Lessors Association, 80% of all companies use leasing to acquire some or all of the machinery and equipment they use to run their business. Henkel s lease-to-own program provides an effective way for your business to acquire almost any Henkel equipment. Leases can be customized to each company s needs. Our program can also include other services and spare parts as part of the equipment lease. Let us customize a lease program to meet your needs. PREVENTATIVE MAINTENANCE CONTRACTS There are many misconceptions about preventative maintenance. One such misconception is that PM is unduly costly. This may be true for some components, but not all. Without preventative maintenance, costs for lost production time from unscheduled equipment breakdown will be incurred. Also, PM will result in savings due to an increase in effective system service life. Long-term benefits of PM include: Improved system reliability Decreased cost of replacement Decreased downtime Better spare part inventory management REQUEST EQUIPMENT SERVICES To learn more about the services Henkel offers, you can visit our website at In addition to our services, the website offers manuals and technical information on Lotite equipment products. By Internet To request a quote or get more information, your request to [email protected]. By Telephone If you wish to speak to us regarding an equipment service, you can call to speak to an equipment services representative. If you have a question regarding equipment set up or operation, our technical information staff is available to help. To contact them, call -800-LOCTITE and choose the technical service option. LOCTITE EQUIPMENT WEBSITE To better support our wide array of equipment services, our Equipment web site provides easy access to all service options and inquiries for all Loctite Equipment you may be interested in. Technical literature, Equipment Showroom locator, operational videos, and much more, are all at your fingertips, for quick and easy access. You can also choose to purchase directly on-line using a major credit card. Select from our wide array of adhesive dispensing and light curing equipment. Shipping time for most items are just to 2 business days. Please visit the site at: Henkel can create a PM contract that fits your specific equipment and work with your maintenance staff to insure maximum up time of your equipment. 4

7 Dispense Systems Loctite brand dispense systems, available from Henkel, are designed to offer the total package for fluid delivery. Whether you use a Loctite brand adhesive product, or any other brand, these complete systems are ready for immediate operation and offer the manufacturing flexibility and reliability you re looking for. Selection of a Loctite brand complete dispensing system is based on the product being used, package size, and process requirements. DISPENSING Dispense Systems PRODUCT Item Number Dispense Patterns Used to Dispense Package Types & Sizes Viscosity Range Vacuum Suck-Back VOLUMETRIC BOTTLE DISPENSERS Dispense adhesive directly from product bottle with no reservoirs required. Loctite Benchtop Peristaltic Dispenser Dots, Drops, Beads Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers Any 0 to 5,000 cp N/A COMPLETE PRESSURE-TIME BOTTLE DISPENSE SYSTEMS Equipped with all components needed to dispense a wide range of products in a variety of adhesive bottle sizes. Loctite Bond-A-Matic 3000 Dispenser 0-5 psi Loctite Bond-A-Matic 3000 Dispenser 0-00 psi Dots, Drops, Beads Gel Adhesives, Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers 250 ml bottle lb. bottle L bottle 2 kg bottle 200 g squeeze tube Low Medium to High N/A Loctite Shot Miser Dispense System See page 8 Dots, Drops, Beads Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers 250 ml bottle lb. bottle Low to Medium N/A SYRINGE DISPENSING SYSTEMS Choose the Loctite Posi-Link Volumetric Dispense System for the highest level of dispense precision. Loctite Posi-Link Dispensing System See page 9 Dots, Drops, Beads Gel Adhesives, Instant Adhesives, Light Cure/Acrylics, Epoxies Prepackaged 5 ml syringe 0 ml syringe 25 ml syringe Low to Paste Yes Loctite Precision Syringe Dispensing System Loctite Digital Syringe Dispensing System Loctite Foot Pedal Dispenser 97006* * 98050* Dots, Drops, Beads Dots, Drops, Beads Dots, Drops, Beads Gel Adhesives, Instant Adhesives, Light Cure/Acrylics Gel Adhesives, Instant Adhesives, Light Cure/Acrylics Gel Adhesives, Instant Adhesives, Light Cure/Acrylics THREAD SEALANT & ANAEROBIC GASKETING DELIVERY SYSTEMS Ensure consistent application of high viscosity thread sealants and anaerobic gasketing applications. Loctite Dial-A-Seal Applicator N/A Pipe Sealants 3 ml syringe 5 ml syringe 0 ml syringe 30 ml syringe 55 ml syringe 50 ml tube 250 ml tube L bottle Low to Paste Low to Paste Low to Paste Medium to High Yes Yes 98049: No 98050: Yes N/A Loctite Pump-A-Bead II Dispenser Beads Anaerobic Gasketing 850 ml cartridges Medium to High N/A TUBE BONDING Light Cure Acrylic Delivery System. Loctite Light Cure Acrylic Adhesive Dispensing System Beads on Tubing OD Light Cure Acrylics 2.0 to 6.0 mm ID Tubing Low N/A * Syringe Air Line Adapter sold separately. See page 83. 5

8 Dispense Systems DISPENSING VOLUMETRIC BOTTLE DISPENSER LOCTITE BENCHTOP PERISTALTIC DISPENSER Item Number: The Loctite Benchtop Peristaltic Dispenser is a reliable and effective volumetric dispenser for single- component, low viscosity fluids up to 5,000 cp, directly from the product bottle. It is great for applications that require dispensing of fluids where a precise bead or specific flow rate is necessary. This dispenser is electro - mechanically operated and does not require the use of an air source. Air-free dispensing eliminates air in product avoiding premature product clogging of cyanoacrylates Instant reverse for vacuum suck-back that shuts off the flow of liquid and prevents dripping Adjustable post- delay time for vacuum setting Simple and convenient load mechanism provides for easy tube changes Continuous or timed mode of dispense Large digital LED display Includes four (4) different feed line tubing sizes to accommodate various product viscosities The hand held applicator with extended tubing and matching nozzle is positioned through an eccentric rotor pump assembly and then inserted into any product bottle. Rotation speed and time of the rotor motion is then adjusted to dispense the precise and repeatable drop or bead. The peristaltic motion of the rotor imparts pressure on the tube and pumps product out of the bottle. The rotor can then be set up to reverse after the dispense cycle to provide suck- back and prevent dripping. Rotor direction can also be adjusted to accommodate placing either end of the tube in the product bottle. Digital time controls effectively provide a wide range of dispense cycles to meet your specific process requirements. Power Supply Power Consumption Dispense Time Range Rotor Speed Maximum Flow Rate Minimum Drop Size Dimensions Weight Used to Dispense Viscosity Dispense Range Package Types & Sizes Suck-Back 0/220 VAC; 50/60 Hz 0.3 amps 0.0 to 99.9 seconds Up to 20 rpm Up to 6 ml per minute 0.00 ml 7.2" W x 3.2" H x 6.7" D 6.6 lbs. Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers 0 to 5,000 cp 0.00 ml up to 6 ml/minute Any Programmable by reversing the direction of rotor Parts Included () Silicone Grease () Applicator Assembly () Manual Feed Tubing:.6 mm O.D. x.0 m Clear 2.5 mm O.D. x.0 m Black 2.0 mm O.D. x.0 m Clear 3.2 mm O.D. x.0 m Black Applicator Nozzles:.2 mm ID.9 mm ID.5 mm ID 2.4 mm ID Additional Information For Spare Parts and Accessories see pages Additional Accessories Sold Separately 9850 Loctite Applicator Holder 6

9 DISPENSING Dispense Systems COMPLETE PRESSURE-TIME BOTTLE DISPENSE SYSTEMS LOCTITE BOND-A-MATIC 3000 DISPENSER Item Numbers: and The Loctite Bond-A-Matic 3000 Reservoir Dispense Systems with applicator are reliable, low cost pneumatic dispensers for single - component adhesives. The systems arrive ready to dispense, complete with a 2- liter pressure reservoir and a Loctite Vari-Drop applicator. This item is available with a 0 to 5 psi pressure regulator which is well suited for low viscosity (< 3,000 cp) adhesives, and a 0 to 00 psi regulator for higher viscosity (>3,000 cp) adhesives. Improved dispensing control to eliminate waste, and reduce operator fatigue PTFE lined, black feed line provides a light and moisture barrier to ensure no- clog dispensing of light sensitive acrylics and moisture sensitive instant adhesives Dispensing needle assortment allows you to select the needle to deliver the bead or dot size needed for your application Easy- to- read pressure gauge Adjustable pressure regulator Operation of this unit is easy. An operator will place a bottle of product directly in the reservoir and tighten the three handles on the cover. The unit is then pressurized to the appropriate setting for optimal flow control. The product is dispensed through a hand held Loctite Vari- Drop Applicator which, when depressed, allows material to flow. A fully depressed finger switch maximizes flow. By adjusting the flow screw on the finger switch, a consistent flow can be set for repeatable dispensing. Air Input Clean, dry air not to exceed 25 psig and filtered with a maximum of 50 microns Air Output 98279: 0 to 5 psi : 0 to 00 psi Product Viscosity 98279: 0 to 3,000 cp : >3,000 cp Maximum Distance from System to Dispense Point 48 inches Overall 3.25" H x 9.875" W x 4.625" Diameter Dimensions Internal Reservoir 0" H x 5" Diameter Weight 8 lbs. Used to Dispense Gel Adhesives, Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers Package Types & Sizes 250 ml bottle / lb. bottle / L bottle 2 kg bottle / 200 g squeeze tube Parts Included () Loctite Bond-A-Matic Reservoir with 4" tank fitting () Loctite Vari-Drop Applicator Kit () 4" Feed Line and Spring Strain Relief () Anti-Bubble Tip & Sleeve () Needle Assortment Kit () Tube of Silicone Grease () Manual Additional Information For Spare Parts and Accessories, see page 84. For Dispense Tips, see pages Additional Accessories Sold Separately Reservoir Liner Empty lb. HDPE Bottle 7

10 DISPENSING Dispense Systems LOCTITE SHOT MISER DISPENSE SYSTEM Combination of Item Numbers: 98079, and The Loctite Shot Miser Dispense System is designed for both manual and timed dispensing of all single component products with viscosities ranging from 0 to 80,000 cp. All wetted components are inexpensive and disposable, resulting in low maintenance costs and minimal downtime. The complete system requires the purchase of three separate components; a reservoir, controller, and dispense valve. The reservoir will directly accept 250 ml and pound product bottles (but not liter containers). The operating manual and all controls are in both English and Spanish. LOCTITE SHOT MISER VALVE CONTROLLER Item Number: (see page 8) Electro-pneumatic timer/controller for dispense valve that directly interfaces with any Loctite brand automatic dispense valve (excluding item 976) Multiple range, adjustable timer (0. sec to 99 minutes) Foot switch actuated LOCTITE SHOT MISER DISPENSE VALVE Item Number: (see page 7) Pneumatically actuated pinch-tube dispense valve capable of dispensing drops and beads Disposable fluid path for fast, easy, and low cost maintenance 4" diameter product feed tube Adjustable valve stroke for enhanced shot size control LOCTITE SHOT MISER LITER RESERVOIR Item Number: (see page 22) liter internal capacity reservoir, directly accepts all Loctite brand product bottles in 250 ml and pound bottle package sizes Adjustable pressure regulator, 0 to 00 psi Easy-to -read pressure gauge (units in psi and bar) A pressure/vent valve and hand-tight lid knobs allow for easy, no-tool bottle changeover Tank fitting accommodates 4" diameter product feed tube The container of adhesive is placed in the product reservoir and the system is pressurized using a pneumatic air source. The controller s analog adjustable timer controls the opening and closing of the dispensing valve. The dispense cycle is initiated by the pneumatic foot pedal. The amount of dispensed adhesive is controlled by adjustment of air pressure, valve open time, and the size of the dispensing needle. Pneumatic Supply Electrical Power Fluid Pressure Product Viscosity Controller (98079) Dispense Valve (98085) Reservoir (98090) Used to Dispense Package Types & Sizes Parts Included Additional Information Dimensions Weight Dimensions Weight Dimensions (Overall) Internal Reservoir Weight 60 to 00 psi minimum 20 VAC; 50/60 Hz 00 psi maximum 0 to 80,000 cp 3.875" H x 6.0" W x " Depth 3.5 lbs " H x 5.875" W x.75" Depth 0.5 lbs. 3.3" H x 8.5" Diameter (6.5625" diameter without stand) 7" H x 3.75" Diameter 8.5 lbs. Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers 250 ml bottle / lb. bottle () Shot Miser Reservoir with Stand () Shot Miser Controller with Foot Switch () Shot Miser Dispense Valve with 4" diameter product feed tube () Dispense Tip Sample Kit () Valve Air Line () Manual For Spare Parts and Accessories, see page 84. For Dispense Tips, see pages

11 Loctite Posi-Link Dispense System for Prepackaged Syringes the DISPENSING The Loctite Posi-Link Dispensing System is a programmable, volumetric dispense system that is designed to provide the highest level of dispensing precision directly from a disposable syringe barrel. No need to worry about product temperature or product viscosity changes. This innovative, patent pending design utilizes a positive link between a step motor and a mechanical plunger via a noncompressible hydraulic fluid, to ensure precise adhesive dispensing down to 0.00 ml drop sizes. See, page 0. COMPLETE LOCTITE POSI-LINK SYRINGE SYSTEM AGE of Volumetric Control The END of wetted components and adhesive downloading Dispense Systems Loctite Posi-Link Syringe System Controller + Actuator + Nest LOCTITE POSI-LINK CONTROLLER Item Number: Provides all operator interface and control signals to actuator. (Each Item Sold Separately) Dose selection by volume Easy programming controller, with storage capacity for 25 user defined programs, reduces adhesive set-up waste Smallest footprint on the market to conserve benchtop space Automatic syringe engagement to ensure easy and error-free syringe changeover Adhesive level monitoring with low level visual and digital outputs Fault detection with visual and digital outputs for clogged nozzles, loss of pressure, and system faults In- cycle visual and digital outputs Foot switch, finger switch or PLC remote start activation LOCTITE POSI-LINK ACTUATORS Item Numbers: See chart Provides adhesive dispensing by effecting incremental movements of syringe piston and displacing programmable quantities of adhesive within syringe barrel. Flexible orientation in any position Easily fits below an industrial workbench or wall mounts with brackets supplied to conserve benchtop space Lightweight remote dispense head has a positive link to actuator via a 7 foot tether, allowing ergonomic hand held dispensing or mounting directly on robotic arms Easily attaches to syringe nest (sold separately) to accommodate alternate syringe barrel sizes Adhesive Pressure: Mechanically driven vs. traditional air pressure driven, eliminating risk of air infiltration into adhesive Suck-Back: Prevents drip at end of dispense, and is mechanical driven vs. traditional air vacuum driven, eliminating risk of adhesive being sucked into the system Compact controller and floor mounted actuator leaves benchtop wide open for manual applications. See pages 30-3 for more information on Loctite Posi-Link for dual cartridge applications. PRODUCT Loctite Posi-Link 5-25 Actuator Loctite Posi-Link 0-50 Actuator Item Number Application Type Syringe Barrel Size Recommended for Hand Held Recommended for Mounted or Robotic 5, 0, 25 ml 0, 25 ml See pages 30-3 for use with dual component epoxy cartridges. 9

12 DISPENSING Dispense Systems Loctite Posi-Link Syringe System LOCTITE POSI-LINK SYRINGE NESTS Item Numbers: See chart Connects actuator to syringe barrel. No tool syringe changeover No contact with adhesive. Disposable syringes are the only component in contact with the adhesive No adhesive downloading. Directly accepts Loctite brand pre- filled syringes, plus many other brands Also available, 9850 Loctite Applicator Holder. See page 83. Loctite Posi-Link Syringe Nest Selection 5 ml Syringe 0 ml Syringe 25 ml Syringe * N/A Used With Loctite Posi-Link 5-25 Actuator Loctite Posi-Link 0-50 Actuator * can only be used with product viscosity up to 5,000 cp. Use actuator and nest, for 25 ml syringes over 5,000 cp. Suitable for hand held applications. PRODUCT Loctite Posi-Link Controller Loctite Posi-Link 5-25 Actuator Loctite Posi-Link 0-50 Actuator Item Number Power Source 9' communication cable to actuator 00/240 VAC; 47/63 Hz 00/240 VAC; 47/63 Hz Dimensions 5.375" H x 6" D x 6" W 34" H x 4" D x 5" W 34" H x 4" D x 5" W Total Weight 2 lbs. 2 lbs. 3 lbs. Dispense Head Weight N/A 0.75 lbs..5 lbs. Air Supply N/A 40 to 00 psi 40 to 00 psi Posi-Link Electro/Hydraulic Tether N/A 7 feet 7 feet Minimum Dispense Volume N/A 0.00 ml 0.00 ml Maximum Dispense Rate N/A 0.4 ml /second 0.4 ml /second Maximum Cycle Rate N/A cycle per second cycle per second Parts Included () Posi-Link Controller () Foot Switch () Posi-Link Actuator () Air Inlet Pressure Regulator/Gauge () 0 Power Cord () 9' Communication Cable (2) Wall or Table Mounting Bracket () Instruction Manual Additional Information For Spare Parts and Accessories, see pages Additional Accessories Sold Separately Loctite Syringe Finger Switch Loctite Posi-Link Actuator Functionality Diagram A disposable syringe is effectively used as a metering piston/cylinder. Because the syringe barrel is of a known and constant diameter, a given incremental movement of the syringe piston will displace a known volume of adhesive within the syringe barrel. The controller unit is programmable to initiate a dispense cycle at the specific volumetric amount. It controls the electronic signaling that activates the step motor inside the actuator housing. External air pressure provides constant force on the plunger within the dispense head. With the initiation of a dispense cycle, the following 3 events occur simultaneously:. The step motor rotates a programmed number of revolutions, moving the lead screw, and increasing the hydraulic volume of the stepping cylinder. 2. Hydraulic fluid flows from the remote dispense head to the stepping cylinder, releasing the plunger within the dispense head to travel downward in a controlled incremental movement. 3. As the dispense plunger travels the controlled increment, it displaces (dispenses) a calculated volume of adhesive from the syringe barrel. AIR PRESSURE CONSTANT ON AIR PRESSURE CONSTANT ON REMOTE DISPENSE HEAD NON-COMPRESSIBLE HYDRAULIC FLUID ENCLOSURE STEP MOTOR STEP MOTOR SYRINGE NEST PRE-PACKAGED SET DISPOSABLE SYRINGE PISTON DISPOSABLE SYRINGE BARREL 7 HYDRAULIC HOSE STEPPING CYLINDER LEAD SCREW MOTOR [OFF] MOTOR [ON] ADHESIVE NO FLOW FLOW DISPOSABLE NEEDLE The RED represents the fluid path. 0

13 DISPENSING Dispense Systems SYRINGE DISPENSING SYSTEMS LOCTITE PRECISION SYRINGE DISPENSING SYSTEM Item Number: The Loctite Precision Syringe Dispenser is a pressure-time-vacuum unit designed to dispense adhesive products packaged in 3, 5, 0, 30, 55 and 300 ml cartridges. The unit can be operated in the manual or automatic timed dispense mode to dispense dots, beads, or to fill syringes. Precision air pressure regulator for precise application of small dots Precise digital display of dispense pressure, 0 to 00 psi Digital timer display, for precise timer settings Vacuum suck-back feature to prevent dripping and stringing Stand- up design, requires minimal bench space Detects ±0% variation from set pressure and alerts operator if detected Power Supply This system uses all digital controls to regulate time and air pressure applied to an adhesive or fluid contained within any syringe barrel. When the dispense cycle is initiated, a pulse of air, either timed or manually controlled, is transmitted to the top of the syringe barrel via an air line adapter (required and sold separately). The amount of product dispensed is controlled by the amount of pressure applied to the product, the length of the dispense cycle, the size of the dispense needle, product viscosity, and temperature. Air Supply Pressure Regulator Product Viscosity Dispense Time Range Dimensions Weight Used to Dispense Package Types & Sizes Parts Included Air Line Adapters (Required for syringe dispensing, see page 83.) Additional Information Selectable 90/260 VAC; 47/63 Hz Minimum - 30 psi 0 to 00 psi Low to Paste 0.0 to 99.9 minutes 5.9" W x 9.0" H x 0.4" D 6.7 lbs. Gel Adhesives, Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers 3 ml / 5 ml / 0 ml / 30 ml / 55 ml syringes () Digital Syringe Controller () Foot Switch () Power Cord () Manual For 3 ml syringe dispensing: order For 5 ml syringe dispensing: order For 0 ml syringe dispensing: order or 9726 For 30 ml syringe dispensing: order or For 55 ml syringe dispensing: order or 9846 For Syringe Accessories, see page 83. For Dispense Tips, see pages Additional Accessories Sold Separately for and Loctite Applicator Holder Loctite Syringe Finger Switch Assembly. Used in place of the foot switch to allow finger actuation while holding the syringe barrel Loctite Vertical Syringe Stand

14 DISPENSING Dispense Systems LOCTITE DIGITAL SYRINGE DISPENSING SYSTEM Item Number: The Loctite Digital Syringe Dispenser is a semi- automatic dispensing system designed to dispense adhesives and fluids packaged in 3, 5, 0, 30, and 55 syringes and 300 ml cartridges. The unit has digital timing control with decimal settings to 0.00 seconds for increased precision over typical pressure- time systems. An adjustable pressure regulator controls a pulse of air, and when used in conjunctions with an air line adapter attached to an adhesive syringe barrel, will provide a controlled dispensed amount of adhesive. The system can be operated in the manual, incremental, or timed (automatic) dispense mode to dispense dots, beads or to fill syringes. Vacuum suck-back can effectively control product dripping or stringing Manual, Incremental, and Timed modes allow a choice of adhesive dispensing methods Convenient teach mode to set time required for desired dispense amount or volume Cycle counter is clearly displayed in the LCD screen The unit can be integrated into customer s PLC programming to initiate a dispense cycle Units can be stacked securely to save workspace The system is a pressure-time-vacuum dispense system. It consists of an air regulator and pressure gauge to control pressure, and an electrical timing circuit to control the dispense cycle. When the dispense cycle is initiated, a pulse of air, either timed or manually controlled, is transmitted to the top of the syringe barrel via an air line adapter. The amount of product dispensed is controlled by the amount of pressure applied to the product, the length of the dispense cycle, the size of the dispense needle, product viscosity, and temperature. Power Supply Air Supply Pressure Regulator Product Viscosity Dispense Time Range Dimensions Weight Used to Dispense Package Types & Sizes Parts Included Additional Air Line Adapters (Available for syringe dispensing, see page 83.) Universal Power Supply 0/230 VAC; 50/60 Hz 35 to 00 psi, 4" FNPT 0 to 00 psi Low to Paste to seconds 6.0" W x 7.875" H x " D 2.6 lbs. G, IA, LCD, RC, TL 3 ml, 5 ml, 0 ml, 30 ml and 55 ml syringes / 300 ml cartridges () Digital Syringe Dispenser with Universal Power Cord () Foot Switch with Cord Lock () Manual () 0 ml & () 30 ml Syringe Adapter () Syringe Stand () 6 mm OD air line x 6 ft. (4) Air supply fittings () Air Line Support Mast () Needle Sample Kit For 3 ml syringe dispensing: order For 5 ml syringe dispensing: order For 0 ml syringe dispensing: order or 9726 For 30 ml syringe dispensing: order or For 55 ml syringe dispensing: order or 9846 Additional Information For Dispense Tips, see pages Additional Accessories Sold Separately (see item page.) Loctite Syringe Finger Switch Assembly. Used in place of the foot switch to allow finger actuation while holding the syringe barrel. LOCTITE FOOT PEDAL DISPENSER Item Numbers: and The Loctite Foot Pedal Dispenser is a manually controlled, pneumatic dispenser for use with 3, 5, 0, 30 and 55 syringes, and 300 ml cartridges. It is designed as a floor unit to eliminate the need for bench space. The unit is capable of dispensing dots, drops or beads of fluids ranging from medium viscosity liquids to high viscosity pastes. The dispense cycle is controlled by a manual foot pedal and an adjustable pressure regulator. Item includes a suck- back feature to prevent dripping Air Input 60 to 00 psi when dispensing low viscosity fluids. Air Output 20 to 00 psi Simple hands- free operation Adjustable pressure regulator, 20 to 00 psi Easy-to-read pressure gauge Available vacuum suck-back, to 5 in. Hg, to prevent dripping Designed as floor unit to eliminate the need for bench space When the foot pedal is actuated, a pulse of air is transmitted through an air line adapter (sold separately) to the top of the syringe barrel, pushing a controlled amount of material out of the dispense tip. The amount of product dispensed is controlled by the amount of air pressure applied to the product, the length of time the foot switch is depressed, the size of the dispense tip, the product viscosity, and the temperature. Product Viscosity Low to Paste Vacuum Suck-Back 98049: No 98050: to 5 in. Hg vacuum Dimensions 98049: 8.0" W x 4.675" H x 4.375" D 98050: 8.0" W x 4.675" H x 5.0" D Weight 98049: 3.7 lbs : 4. lbs. Used to Dispense Gel Adhesives, Instant Adhesives, Light Cure/Acrylics Package Types & Sizes 3 ml, 5 ml, 0 ml, 30 ml and 55 ml syringes / 300 ml cartridges Parts Included () Foot Pedal Dispenser (Air Line Adapter sold separately) () Manual Air Line Adapters (Required for syringe dispensing, see page 83.) Additional Information For 3 ml syringe dispensing: order For 5 ml syringe dispensing: order For 0 ml syringe dispensing: order or 9726 For 30 ml syringe dispensing: order or For 55 ml syringe dispensing: order or 9846 For Syringe Accessories, see page 83. For Dispense Tips, see pages Additional Accessories Sold Separately 9850 Loctite Applicator Holder Loctite Vertical Syringe Stand Dispense Key G = Gel Adhesives IA = Instant Adhesives LCD = Light Cure/Acrylics RC = Retaining Compounds TL = Threadlockers 2

15 THREAD SEALANT & ANAEROBIC GASKETING DELIVERY SYSTEMS LOCTITE DIAL-A-SEAL APPLICATOR Item Number: The Loctite Dial- A - Seal Applicator is a touch actuated, all-pneumatic applicator for dispensing high viscosity Loctite product onto threaded pipe fittings and nipples. The system has a quick turn turret that is equipped with cavities for 6, 8, 4, 3 8, 2, 3 4 and inch male pipe threads. The unit accepts 50 ml or 250 ml tubes or liter wide mouth bottles. The product dispense quantity can be adjusted with a rear adjustment knob. The upper limit per dispense cycle is 0.7 ml. It is recommended specifically for applying Loctite PST Thread Sealants, Loctite Vibra-Seal, and Loctite Anti- Seize products. Applicator is fed directly from a 50 ml tube, 250 ml tube, or one liter bottle A quick turn turret is equipped with cavities for 6, 8, 4, 3 8, 2, 3 4 and " male pipe threads Up to 0.7 ml of product can be dispensed per shot Adjustable dispense volume Suggested settings for each diameter fitting are pre-printed on unit A turret head with a cavity for each size of pipe thread is attached to the output of an air actuated, positive displacement pump. The operator presses a fitting down into the correct cavity. The downward motion of the turret depresses a switch that actuates the pump. A metered amount of material is dispensed on the part. Air Input Product Viscosity Turret Sizes Dimensions Used to Dispense Package Types & Sizes Requires filtered (40 micron) lubricated air, 60 psi min. Medium to High 6, 8, 4, 3 8, 2, 3 4 and " (NPT) 7.5" W x 2.2" L (Height with 50 ml tube = 4.4" / Height with L bottle = 6.7") Loctite 565 PST, 567 PST and Vibra-Seal Thread Sealants, and Loctite brand Anti-Seize products 50 ml tube / 250 ml tube / L bottle Parts Included () Loctite Dial-A-Seal Applicator (2) Elbow Fittings () Stand for Liter Bottle () Tube Vent () Liter Bottle and Cap () Feed Tube () 50 ml Tube Adapter () Tube Adapter () Empty 50 ml Tube with Dispense Cap () Manual Additional Information For Spare Parts and Accessories, see page 84. DISPENSING Dispense Systems LOCTITE PUMP-A-BEAD II DISPENSER Item Number: The Loctite Pump-A-Bead II is an all- pneumatic dispense system for pumping Loctite anaerobic gasketing materials from 850 ml cartridges. A pneumatically- driven, reciprocating, positive displacement piston pump provides for consistent dispensing and ensures that air is not introduced into the product. This system is well suited for stationary or bead dispensing. The Loctite Poppet Valve is also included and is ideal for dispensing continuous beads at high pressures. Air piloted control signal initiates dispensing Air- driven, reciprocating, positive displacement piston pump Poppet-type dispensing valve can be mounted onto a robotic arm Anti- drip feature Capable of dispensing 0.5 cc per second Visual signal will indicate Product Cartridge Empty Easily integrated into robotic dispensing stations A full cartridge of material is loaded into the system and the unit is switched to operate mode. Upon demand for dispensing, i.e., pneumatic signal, material is fed from the cartridge to an oscillating pump where the pressure is elevated to greater than 650 psi. Material is forced through a high-pressure hose to the dispense valve where it is dispensed onto the part. Air Input All-pneumatic system, 60 to 00 psi, filtered to 40 microns Product Viscosity Medium to High Compatible Materials Loctite brand de-aerated anaerobic gasketing materials up to,000,000 cp viscosity Pumping Rate 0.5 cc per second Dimensions 6.3" H x 37.2" W x 9.3" D Weight 80 lbs. Used to Dispense Loctite Gasket Eliminator and other Loctite brand Flange Sealants Package Types & Sizes 850 ml cartridges Parts Included () Pump-A-Bead II () Poppet Valve Applicator () Manual Additional Information For Spare Parts and Accessories, see page 84. 3

16 Dispense Systems DISPENSING TUBE BONDING LOCTITE LIGHT CURE ACRYLIC ADHESIVE DISPENSING SYSTEM Item Number: The Loctite Light Cure Acrylic Adhesive Dispensing System is a dispensing system that rapidly and consistently applies a uniform coating of light cure acrylic adhesives to the outer diameter of tubing without adhesive getting into the internal surface of the tube. The dispenser can accommodate circular tubes from 2.0 mm to 6.0 mm in diameter (depending upon bushing size); with a maximum engagement depth of up to 8 mm. Adhesive dispensing onto various diameter tubes is accomplished by using specifically sized stainless steel bushings on the dispense orifice. These bushings are easily interchanged on the dispenser. An electric motor continuously re- circulates adhesive through the dispensing bushing, thus eliminating waste and insuring adhesive is readily available when tubing is inserted into the dispenser. Adhesive Compatibility This unit is designed for use with Light Cure Acrylic Adhesives only. It should not be used with Cyanoacrylates or Light Cure Cyanoacrylates. Uniform and consistent tube coating using simple one hand operation Bushing design insures no adhesive contamination of internal tube surface Easy adhesive adjustment allows operator to optimize adhesive dispense amount Optional bushings allow a variety of tube diameters Versatile system designed to apply adhesive to the outer diameter of tubing with optional bushings available Design prevents light exposure of adhesive in the dispenser Electric pumping mechanism provides constant adhesive supply and eliminates the need for compressed air Built- in adhesive level sight glass The operator adjusts the adhesive application rate to optimize the amount of adhesive applied to the assembly. When the tubing is inserted into the bushing, an internal spring retracts and allows the tubing to be inserted. Upon removing tube, a uniform bead, up to 8 mm, is applied with no adhesive getting onto any internal surface of the tube. Utilities 0 VAC; 0 amps; 60 Hz Overall Dispenser Dimensions 9.0" H x 6.0" Diameter base Overall Transformer Dimensions 2.3" H x 3.5" W x 4.2" D Weight Dispense Unit 7.7 lbs. / Transformer.25 lbs. (Not Shown) Adhesive Volume of Dispenser 30 ml NOT RECOMMENDED FOR TUBING BELOW 70 SHORE A () Light Cure Acrylic Adhesive Dispensing System Parts Included () Transformer () Retaining Ring Pliers () Manual () Power Cord LCA Tubing Adhesive Applicator Bushing Selection Guide (Standard Bushing) Item Number Description Tubing OD Range mm (0.079 in.) 0.59 in. to in mm (0.8 in.) in. to 0.28 in mm (0.57 in.) 0.28 in. to 0.67 in mm (0.97 in.) 0.68 in. to in mm (0.236 in.) in. to in. 4

17 Controllers & Reservoirs Loctite brand controllers and reservoirs can be used as the chief components, along with a selection of Loctite brand parts and accessories or with your own parts, to create a complete custom dispensing system, designed to meet your specific needs and manufacturing goals. Selection of a Loctite brand controller and reservoir is based on the adhesive or fluid being used, the package or container the adhesive or fluid is supplied in, and the overall requirements of the manufacturing process. DISPENSING Controllers & Reservoirs PRODUCT Item Number Controlled Outputs Number of Dispense Valves MULTI-FUNCTION CONTROLLERS Select when you need more functionality than just single valve dispensing. Loctite Single Channel Automatic Controller Loctite Spray Valve Controller Loctite Digital Multi-Functional Controller (Dependent) SINGLE FUNCTION CONTROLLERS Select to operate a single dispense valve. Advancing Slide mm mm Rotospray N/A N/A (Independent) mm In conjunction with Positive Displacement Pump , see page 72. Loctite Digital Dispense Controller 970 N/A N/A Loctite Shot Miser Valve Controller N/A N/A Item Pressure Package Viscosity Low Level PRODUCT Used to Dispense Number Regulation Types & Sizes Range Sensing INTEGRATED RESERVOIR CONTROLLERS Space saving and economical, combined controller and reservoir for valve dispensing Gel Adhesives, 250 ml bottle Low to No Loctite Integrated 0 to 5 psi Instant Adhesives, lb. bottle Medium Yes Semi-Automatic Light Cure/Acrylics, L bottle Dispenser Retaining Compounds, 2 kg bottle Medium No 0 to 00 psi 9707 Threadlockers 200 g squeeze tube to High Yes RESERVOIRS Select your reservoir based on product viscosity and need for low level sensing Yes 0 to 5 psi Gel Adhesives, 250 ml bottle Low to Yes Loctite Instant Adhesives, lb. bottle Medium No Bond-A-Matic Light Cure/Acrylics, L bottle 3000 Reservoir Retaining Compounds, 2 kg bottle Yes Medium to 00 psi Threadlockers 200 g squeeze tube Yes to High No Loctite 300 ml Cartridge Pusher Loctite 2.25 Gallon Pressure Reservoir Loctite Shot Miser Reservoir to 50 psi to 60 psi to 00 psi Gel Adhesives, Anaerobic Gasketing, Light Cure/Acrylics, Low Viscosity Silicones Gel Adhesives, Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers 300 ml cartridge 250 ml tube 250 ml bottle lb. bottle L bottle 2 kg bottle 200 g squeeze tube 250 ml bottle lb. bottle 200 g squeeze tube Medium Low to Medium Low to High Yes No No Loctite 4 Liter Gravity Feed Reservoir N/A Retaining Compounds, Threadlockers Direct Fill Low to Medium Yes 5

18 Controllers & Reservoirs DISPENSING MULTI-FUNCTION CONTROLLERS LOCTITE SINGLE CHANNEL AUTOMATIC CONTROLLER Item Number: 9723 The Loctite Single Channel Automatic Controller is a multi- function system for operating one or two dispense valves while controlling peripheral equipment such as advancing slides and rotor spray units. Process functions are programmed by the front panel keyboard and aided by a visual display. High precision control is possible with the fine tuning of both time and pressure variables. Control of reservoir pressure, advancing slide delay, and rotor spray operation can all be selected or removed from use individually. This system can be used with low level sensors such as Loctite Bond- A - Matic reservoirs or integrated into fully automatic production lines using the PLC interface. Fully programmable, independent controller with permanent software set-up Front mounted keyboard and multilingual display for easy system programming and dispense valve control Digital pressure readout for precise electronic pressure regulation and monitoring of reservoir and valve dispensing Digital time display and control of valve dispensing Capable of controlling one or two dispense valves with advancing slide and rotor spray unit Operator pre -programming determines which devices are to be used for a particular application. Once a particular set-up is selected, valve pressure, open time and advancing slide timing can all be adjusted to meet a specific dispensing need. Power Supply Air Input Air Output Number of Dispense Valves Dimensions Weight Parts Included Additional Information 90/260 VAC; 47/63 Hz 58 to 6 psi (4 to 8 bar) to 00 psi (0. to 7 bar) 2 (Dependent) 9.0" H x 5.7" W x 0.2" Diameter 6.5 lbs. (3 kg) () Automatic Controller () Pneumatic Tubing, 6 mm O.D. () Power Cord () Manual For Spare Parts and Accessories, see page 84. For Dispense Tips, see pages Additional Accessories Sold Separately Bond-A-Matic 3000 Reservoirs ( or ) 978 Loctite Advancing Slide (50 mm Stroke) 979 Loctite Advancing Slide (00 mm Stroke) 972 Loctite In-Line Flow Monitor 975 Loctite Electric Rotor Spray Note: If used with advancing slide, only one dispense valve can be controlled. 6

19 LOCTITE SPRAY VALVE CONTROLLER Item Number: 9852 The Loctite Spray Valve Controller provides 2 independent air signals and is designed to work integrally with the Loctite Spray Valve (item 98520), providing the open/ close signal and atomizing air supply, see page 69. The digital timing control can be adjusted separately for Pre-Spray, Spray, and Post-Spray time sequences. This timing flexibility allows the unit to be used for any single-acting automatic control valve or hand held pneumatic valve. This unit can also integrate with an external PLC. Microprocessor based timed controller Fully independent valve, open/close and atomization air supply 3 separate timed sequences pre-spray, valve on, post- spray/valve off Timed or manual mode with foot pedal control All time modes maintained in memory with AC power disconnected Product flows from a reservoir under air pressure as provided by the Loctite Spray Valve Controller. The controller also provides air to open/close the valve and a separate atomizing air source to the spray valve nozzle assembly. Timing and pressure controls for atomizing air, fluid line pressure, valve stroke adjustment, height from surface, and material viscosity can be adjusted to optimize required dispense quantity and coverage pattern. Power Source Air Supply Number of Dispense Valves Dimensions Weight Parts Included Nozzle Kit Nozzle Kit 90/260 VAC; 47/63 Hz Minimum 30 psi 2.5" H x 2.5" L x 7.6" D 5.5 lbs. () Controller Unit and Power Cord () Foot Pedal () 4' Air Supply Line and Filter Additional Accessories Sold Separately / Loctite Bond-A-Matic Reservoirs with Low Level Sensors Loctite Replacement Foot Switch / Loctite Bond-A-Matic Reservoirs DISPENSING Controllers & Reservoirs LOCTITE DIGITAL MULTI-FUNCTIONAL CONTROLLER Item Number: The Loctite Digital Multi-Functional Controller is a versatile, programmable controller designed to provide on/ off digital timing and interface logic for up to three independent functions, pneumatic or electric. A typical use for this unit would be to operate a dispense valve, advancing slide mechanism, and a turntable in a workstation. It is readily compatible with low level sensors from Loctite brand reservoirs and the Loctite 300 ml Cartridge Pusher. It has an interface for twohand, anti- tie- down start switches that makes it ideal for workstation applications by eliminating the potential for pinch points. It also includes an interface for a part present sensor, a dispense confirmation sensor, and can provide interface signals to a host PLC. Keypad with LCD display to program the on/off times of multiple devices in 0. second increments Interface connections for reservoir low level sensors, part present sensors, dispense confirmation sensors, slide position switches, electrical motors, indicator lights, foot switch, anti-tie-down switches, PLC communication, etc. Emergency Stop button on front face of the enclosure Fully modular for optimum system configuration The Loctite Digital Multi-Functional Controller, when used with a Loctite Dispense Valve and Reservoir, provides a complete automated dispense system. The controller provides digital timing control for any Loctite brand automatic dispense valve, advancing slide, turntable, or rotospray system. Dispense time range is from 0.0 to seconds in 0.0 second increments for precise and repeatable dispensing. Electrical Air Input Number of Dispense Valves Dimensions Weight Parts Included Input voltage 00/240 VAC; 50/60 Hz 0.6 amps Internal voltage: 24 VDC PSI-G, filtered, dry air at CFM (minimum) 3 (Independent).375" W x 9.25" D x 8.0" H 5 lbs. () Digital Multi-Functional Controller () Foot Switch Assembly () 24 VDC Power Supply () Manual Additional Information For Spare Parts and Accessories, see page 84. Additional Accessories Sold Separately Loctite Advancing Slide (2" Stroke) Loctite 2-Hand Anti-Tie-Down Switch Set Loctite PLC Interface Cable Loctite Cable Connector Plug Kit 7

20 DISPENSING Controllers & Reservoirs SINGLE-FUNCTION CONTROLLERS LOCTITE DIGITAL DISPENSE CONTROLLER Item Number: 970 The Loctite Digital Dispense Controller provides digitally timed dispense control for all Loctite brand automatic dispense valves. It controls the air supply to a remote reservoir and the pneumatic opening of a dispense valve, both sold separately. It is readily compatible with low level sensors from Loctite Bond-A-Matic Reservoirs and the Loctite 300 ml Cartridge Pusher. This unit is fully modular and can integrate with an external PLC. Convenient touch pad for dispense time control Pneumatic output provides air pressure to a fluid pressure reservoir Fluid low level indicator and output to allow protocol with plant PLC Fully modular for use with the Loctite Bond-A-Matic Reservoir or the Loctite 300 ml Cartridge Pusher and Electrical Utilities any dispensing valve Air Input The Loctite Digital Dispense Controller, when used with a Loctite Dispense Valve and Reservoir, provides a complete pressure- time or positive displacement dispensing system, depending on the type of reservoir used. This unit is ideal for manufacturing workstations. Number of Dispense Valves Dimensions Weight Parts Included 90/260 VAC; 47/63 Hz 70 to 45 PSIG filtered (0 micron), dry air at CFM (minimum) 9.5" H x 6.0" W x.0" D 4.6 lbs. () Digital Dispense Controller () Power Cord () Foot Switch Assembly () Manual () Terminating Plug Additional Information For Spare Parts and Accessories, see pages LOCTITE SHOT MISER VALVE CONTROLLER Item Number: The Loctite Shot Miser Valve Controller is an economical choice that provides both manual and timed dispense valve control for any Loctite brand automatic dispense valve. It features a multiple range timer that provides adjustment from 0. seconds to 99 minutes. Electro-pneumatic timer/controller for dispense valve Timed and continuous dispense modes Multiple range, adjustable timer (0. seconds to 99 minutes) Foot switch actuated Rugged, all-steel enclosure with flat top and bottom for easy stacking Directly interfaces with any Loctite brand automatic dispense valve (except item 976) Input Voltage /Cycles Fuse Number of Dispense Valves Dimensions Weight Parts Included 5 VAC; 50/60 Hz amp, 250 VAC, 5 mm x 20 mm, Fast Acting 3.875" H x 6.0" W x " D 3.5 lbs. () Shot Miser Valve Controller () Power Cord () Pneumatic Foot Switch () Manual Additional Information For Spare Parts and Accessories, see page 84. 8

21 DISPENSING Controllers & Reservoirs INTEGRATED RESERVOIR CONTROLLERS LOCTITE INTEGRATED SEMI-AUTOMATIC DISPENSER Item Numbers: 97007, 9700, 9707 and The Loctite Integrated Semi-Automatic Dispense Systems combine a controller and reservoir into a single unit. These popular units provide a less complex and more cost effective dispensing solution when compared to systems with separate reservoirs and controllers. Combined with the digital timing feature, this unit will provide precise dispensing control with any Loctite automatic dispense valve or pneumatic hand held applicator, sold separately. The reservoir is large enough to accept up to 2 kg bottles, and units can be equipped with low level sensing as shown in the chart below. Equipped with a 0 to 5 psi, or a 0 to 00 psi adjustable pressure regulator Easy- to-read pressure gauge Continuous or timed dispense mode from 0.0 to 99.9 seconds Drip funnel for reservoir lid during product changeover 9707 and offer low level sensors, and are recommended when dispensing cyanoacrylate adhesives The unit is connected to an external pneumatic supply, and regulates the adjusted dispensing pressure during the selected dispensing time. A bottle of adhesive is placed directly into the integrated reservoir, and the reservoir lid is clamped in place. It is then pressurized using clean, filtered dry air. Air within the reservoir will push down on the liquid in the bottle and force it through the product feed line to the dispensing valve. Power Supply 90/260 VAC; 47/63 Hz Air Input Minimum 30 psi Air Output 97007: 0 to 00 psi 9700: 0 to 5 psi 9707: 0 to 00 psi 97020: 0 to 5 psi Low Level Sensing 97007: No 9700: No 9707: Yes 97020: Yes Product Viscosity > 3,000 cp 0 to 3,000 cp Dimensions 3.8" H x 4.5" W x 9.2" D Reservoir Dimensions 4.75" diameter x 9.75" H Weight 6.5 lbs. (7.5 kg) Used to Dispense Gel Adhesives, Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers Package Types & Sizes Parts Included Additional Information 250 ml bottle / lb. bottle / L bottle 2 kg bottle / 200 g squeeze tube () Power Cord () Integrated Semi-Automatic Dispenser () Manual () Foot Switch (3) Drip Cups For Spare Parts and Accessories, see pages For Dispense Tips, see pages

22 Controllers & Reservoirs DISPENSING RESERVOIRS LOCTITE BOND-A-MATIC 3000 RESERVOIR Item Numbers: , 98272, , , and The Loctite Bond-A-Matic 3000 Reservoirs, our most versatile and popular units, can be used in a wide array of dispensing applications. These units are available in 2 dispensing pressure ranges for a wide range of product viscosities. The reservoir can also be equipped with low level sensors that send an electronic signal to a Loctite brand controller (items 970, 9723 or ), sold separately. User- friendly design Can accommodate a variety of Loctite brand product packages Available with optional low level sensor All pneumatic operation Operation of this unit is easy. An operator will place a bottle of product in the reservoir and tighten the three handles on the cover. The unit is then pressurized to the appropriate setting for optimal flow control. The product is dispensed through an applicator, which when actuated, allows material to flow. Flow rate of the product is dependent on the valve selected, pressure, product viscosity, and needle size. Air Output : 0 to 5 psi : 0 to 00 psi 98272: 0 to 5 psi : 0 to 00 psi : 0 to 5 psi : 0 to 00 psi Product Viscosity 0 to 3,000 cp > 3,000 cp : 24 VDC : 24 VDC Low Level Sensing 98272: 0 VAC : 0 VAC : N/A : N/A Dimensions 3.25" H x 9.875" W x 4.25" D Internal Reservoir 0" H x 5" Diameter Weight 8 lbs. unfilled Used to Dispense Gel Adhesives, Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers Package Types & Sizes 250 ml, lb., L, 2 kg bottles / 200 g squeeze tube Parts Included () Bond-A-Matic 3000 Reservoir with 4" Tank Fitting () 4" Feed Line and Spring Strain Relief () Anti-Bubble Tip and Sleeve () Squeeze Tube Adapter and Nut/Ferrule ( / only) () 3 8" Tank Fitting and Spring Strain Relief ( / only) () Manual () Tube of Silicone Grease Additional Information For Spare Parts and Accessories, see pages Additional Accessories Sold Separately Any Loctite Brand Dispensing Valve Reservoir Liner / Empty lb. HDPE Bottle 20

23 LOCTITE 300 ML CARTRIDGE PUSHER Item Number: The Loctite 300 ml Cartridge Pusher is designed for dispensing low to medium viscosity products. The cartridge pusher mechanically applies pressure to the cartridge plunger using a pneumatically driven ram, removing the possibility of air entrapment in the cartridge. There is a low level sensor that is compatible with Loctite brand controllers (items 970, 9723, or ). An automatic dispense valve will also be required for final application of the product. Controllers and valves are sold separately. Not recommended for high viscosity or paste materials. Mechanical ram provides product pressure, eliminating risk of inducing air into product, as is the case with pneumatic dispensers Equipped with a low level sensor that can be integrated to a PLC or any Loctite brand digital controller A grease reservoir is included which continually applies a thin film of grease to the plunger shaft to maintain free operation of the ram Integral air pressure regulator/gauge The cartridge retainer can be removed for easy maintenance Can be mounted vertically or horizontally The Loctite 300 ml Cartridge Pusher is a front-loaded, free- standing device that can be coupled with a Loctite Digital Dispense Controller, Loctite Digital Multi- Functional Controller, or integrated into an existing work cell. Pressurized air is supplied to the air regulator to control the air pressure that flows into the ram cylinder. A hand lever, pneumatic, three- way valve channels the pressurized air into the pneumatic cylinder. Moving the hand lever toward the cartridge sleeve causes the piston to move forward, pressing product out of the 300 ml cartridge through a product feed line. Moving the hand lever up toward the air cylinder causes the piston to retract. A reed switch assembly is located on the air cylinder, equipped with an LED indicator. Once activated, the LED indicator will light up and the switch will communicate a low level condition to a Loctite Digital Dispense Controller or Loctite Digital Multi- Functional Controller. The reed switch is activated by a permanent magnet located on the piston within the air cylinder. Air Inlet Air Input Product Viscosity Dimensions Weight 8" female NPT 50 psi maximum Low to Medium Gel Adhesives 8.375" H x 5.8" W x " Length 0.6 lbs. Used to Dispense Gel Adhesives, Anaerobic Gasketing, Light Cure/Acrylics, Low Viscosity Silicones Package Types & Sizes 250 ml tube / 300 ml cartridge Parts Included () 300 ml Cartridge Pusher () Fitting Kit () Manual Additional Information For Spare Parts, see pages For Cartridge Accessories, see page 8. For Dispense Tips, see pages DISPENSING Controllers & Reservoirs LOCTITE 2.25 GALLON PRESSURE RESERVOIR Item Number: The Loctite 2.25 Gallon Pressure Reservoir is our largest stand-alone reservoir designed for use with Loctite brand pressure-time dispense systems, sold separately, and will accommodate up to 2 kg packages. The unit is made of heavy, deep-drawn, one-piece steel construction and comes equipped with a pressure regulator, gauge, pressure safety relief valve, and product feed line connector. Rugged construction 0 to 60 psi regulator Pressure safety relief valve 4" NPT air line and 4" product feed line connectors Pressure Range / Capacity 0 to 60 psi / 2.25 gallons Product Viscosity Low to Medium Dimensions / Weight 8.5" H x 2.7" Diameter / 7 lbs. Internal Reservoir 9.5" H x 9.3" Diameter Used to Dispense Gel Adhesives, Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers Package Types & Sizes 250 ml, lb., L, 2 kg bottles / 200 g squeeze tube Parts Included () 2.25 Gallon Pressure Reservoir () Manual Additional Information For Spare Parts and Accessories, see pages

24 Controllers & Reservoirs DISPENSING LOCTITE SHOT MISER RESERVOIR Item Number: The Loctite Shot Miser Reservoir is an economical choice for bottle dispensing operations. It is suitable for a full range of product viscosities, up to 80,000 cp. The reservoir is limited to accept packages no larger than pound product bottles. liter internal capacity reservoir, directly accepts product bottles listed in chart Easy-to-read, 0 to 00 psi pressure regulator Pressure/vent valve and hand-tight knobs for easy, no tool bottle changeover 4" product feed line connector LOCTITE 4 LITER GRAVITY FEED RESERVOIR Item Number: The Loctite 4 Liter Gravity Feed Reservoir is used to gravity feed low to medium viscosity products to a dispensing system. This unit is typically used in rotospray systems, but could be used for any gravity feed application. It can feed one to four Loctite Positive Displacement Pumps (item ), sold separately. Low level sensing options are also available. For use with low to medium viscosity product feeding a dispensing system Feeds up to four Loctite Positive Displacement Pumps Refill on the Fly without stopping operation Low level sensing options for integration with other controls Visual level capability The reservoir is intended to be mounted above the point of use, thus allowing material to flow by gravity to a dispense pump. Material is poured into the reservoir and replenished as required without stopping the operation. Pressure Range / Capacity Product Viscosity Dimensions / Weight Internal Reservoir 0 to 00 psi / Liter Low to High 3.25" H x 8.5" Diameter / 8.5 lbs. 7.0" H x 3.75" Diameter Used to Dispense Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers Package Types & Sizes 250 ml bottle / lb. bottle / 200 g squeeze tube Parts Included () Shot Miser Liter Reservoir () 6' Product Supply Tube () Anti-Bubbler Adapter & Sleeve () Spring Guard () Manual Additional Information For Spare Parts and Accessories, see pages Additional Accessories Sold Separately Reservoir Liner Empty lb. HDPE Bottle Low Level Sensor Available as an option in 24 VDC or 20 VAC Size of Reservoir Four liters maximum Product Viscosity Low to Medium Dimensions 7.3" W x 8.7" Depth x 2.75" H (9.625" H with lid up) Internal Reservoir 2.0" H x 6.6" Diameter Weight 4.5 lbs. unfilled Used to Dispense Retaining Compounds, Threadlockers Package Types & Sizes Direct Fill Parts Included () Manual () 4 Liter Gravity Feed Reservoir () Wall Mounting Bracket () Reservoir Casement () Sensor Mounting Bracket () Parts Kit Containing: (3) Reservoir Plugs (4) Male Elbow Fittings () Tube of Loctite 565 PST Thread Sealant Additional Information For Spare Parts and Accessories, see pages Additional Accessories Sold Separately AC Level Sensor Kit DC Level Sensor Kit 22

25 Hand Held Applicators Loctite brand hand held applicators are ergonomically designed for the hand delivery of adhesives and fluids directly from their original package. Whether pneumatic or manual, each item is designed for the simple, clean, hand held dispensing of fluids, and to reduce waste and operator contact over other methods. Selection of a Loctite brand hand held applicator is based on product type, package configuration, and process requirements. DISPENSING Hand Held Applicators PRODUCT Item Numbers Used to Dispense Package Types & Sizes Viscosity Range BOTTLE DISPENSING The most popular hand held bottle top dispensers for Loctite brand threadlockers and other adhesive products. Loctite 50 ml / 250 ml Hand Pumps Retaining Compounds, Threadlockers 50 ml bottle 250 ml bottle Low to Medium Type Manual Loctite Liter Collapsible Bottle Holder Loctite Soft Squeeze Bottles 983 Retaining Compounds, Threadlockers All Fluids in 2 fl. oz. packages All Fluids in 4 fl. oz. packages All Fluids in 8 fl. oz. packages SYRINGE DISPENSING Simple manual dispensers for low volume syringe applications. Loctite 30 ml Manual Syringe Applicator Loctite 0 / 30 ml Syringe Manual Plungers Any fluid in a 30 ml syringe including 25 ml syringes Liter collapsible bottle N/A 9892 Any fluid in a 0 ml syringe 0 ml syringe (3 pack) 9893 Any fluid in a 30 ml syringe 30 ml syringe (3 pack) Low to Medium Low to Medium Manual Manual 30 ml syringe Low to High Manual Low to High TWO-PART DISPENSING Simple and effective two-part dispensers to meet your lower precision dual cartridge application needs. Manual Loctite 50 ml Dual Cartridge Manual Applicators Two-Component Epoxies, Urethanes, Methacrylates 50 ml dual cartridge Low to High Manual Loctite 50 ml Dual Cartridge Pneumatic Applicator Loctite Caulking Gun Conversion Kits for 50 ml Cartridges Loctite 200 ml / 400 ml Dual Cartridge Manual Applicators Loctite 200 ml / 400 ml Dual Cartridge Pneumatic Applicators Loctite Universal Metal Dispenser for 200 ml / 400 ml Cartridges Loctite Fixmaster Rapid Rubber Repair Dispenser Two-Component Epoxies, Urethanes, Methacrylates Two-Component Epoxies, Urethanes, Methacrylates Two-Component Epoxies, Urethanes, Methacrylates 200 ml dual cartridge 400 ml dual cartridge ml dual cartridge ml dual cartridge Two-Component Epoxies, Urethanes, Methacrylates 400 ml dual cartridge ml dual cartridge Two-Component Epoxies, Urethanes, Methacrylates Loctite Fixmaster Rapid Rubber Repair Urethanes CARTRIDGE DISPENSING Manual and pneumatic applications for 300 ml cartridges. Loctite 300 ml Pneumatic Cartridge Dispenser Loctite Foldable 300 ml Cartridge Applicator Loctite 300 ml Pneumatic Cartridge Dispensing Retainer A Gel Cyanoacrylates, Anaerobic Gasketing, Light Cure/Acrylics, Silicones Gel Cyanoacrylates, Anaerobic Gasketing, Light Cure/Acrylics, Silicones Gel Cyanoacrylates, Anaerobic Gasketing, Light Cure/Acrylics, Silicones 50 ml dual cartridge Low to High Pneumatic 50 ml dual cartridge Low to High Manual 200 ml and 400 ml dual cartridges 400 ml Loctite Fixmaster Rapid Rubber Repair dual cartridge 300 ml cartridges 250 ml tubes 300 ml cartridges 300 ml cartridges High to Paste High to Paste High to Paste Medium to High Medium to High Medium to High Low to Medium Manual Pneumatic Manual Manual Pneumatic Manual Pneumatic 23

26 DISPENSING BOTTLE DISPENSING LOCTITE 50 ML / 250 ML HAND PUMPS Item Numbers: 9700 and 9844 Hand Held Applicators The Loctite 50 ml and 250 ml Bottle Hand Pumps are portable, precision, bottle-top applicators that thread directly on any 50 or 250 ml bottle of anaerobic product. Item 9844 is also supplied with a stand to better balance the smaller 50 ml bottle. They are designed to dispense at any angle from 0.0 to 0.04 ml without leaks or product waste. Not suitable for cyanoacrylate adhesives, primers, or activators. Adjustable positive displacement, 0.0 ml to 0.04 ml of product Allows user to control amount and positioning of the adhesive Converts product package into a portable dispenser Applicator nozzle accepts a variety of dispensing needles Bottle stand greatly improves 50 ml bottle stability Each squeeze of the trigger will dispense single shots of Loctite brand threadlockers and retaining compounds from 0.0 to 0.40 ml, with viscosities up to 30,000 cp. This unit requires no flushing, electricity, or air source. Compatibility Product Viscosity Dimensions (9700) Dimensions (9844) Used to Dispense Parts Included 9844: () 50 ml Hand Pump and Stand () Needle Kit () Manual () Hand Pump Washers (3 pack) Additional Information Loctite brand 50 ml or 250 ml anaerobic product bottles Low to Medium 4" H x 5.75" W x.5" Diameter- Pump 4" H x 5.75" W x.5" Diameter- Pump 4.5" H x 3.75" W x 2.25" Diameter- Stand Low Viscosity Thread Sealants, Retaining Compounds and Threadlockers 9700: () 250 ml Hand Pump () Needle Kit () Manual () Hand Pump Washers (3 pack) For Dispense Tips, see pages For Spare Parts and Accessories, see pages LOCTITE LITER COLLAPSIBLE BOTTLE HOLDER Item Number: 983 The Loctite Liter Collapsible Bottle Holder is a lightweight holder designed to facilitate the transfer of anaerobics from our liter collapsible containers. Its nickel plated steel construction is rugged and durable. It resists corroding from moisture and adhesive buildup, allowing repeated use. Dimensions Weight Used to Dispense Parts Included 6.0" H x 5.3" W x 7." D 0.25 lbs. All approved liter collapsible bottles () Liter Collapsible Bottle Holder LOCTITE SOFT SQUEEZE BOTTLES Loctite Soft Squeeze Dispense Bottles are intended for use by customers who wish to download Loctite brand cyanoacrylate adhesives from large containers to smaller, hand held packages. These soft, thin walled polyethylene bottles are ideal for use at manual workstations. A variety of bottle sizes and cap styles are available. Bottles, caps,and dispense tips are sold separately. 5.5" PRODUCT Item Number Description oz. Soft Squeeze Bottle (50 pack) 4 oz. Soft Squeeze Bottle (50 pack) 8 oz. Soft Squeeze Bottle (50 pack) Product Viscosity Dimensions Low to Medium 98345: 3.3" H x.5" Diameter 98346: 4.3" H x.9" Diameter Dunce Cap with red sealer cap for 2 oz. bottle (50 pack) Dunce Cap with red sealer cap for 4 oz. and 8 oz. bottles (50 pack) Luer-Slip Cap for 2 oz. bottle (50 pack) Used to Dispense 98347: 5.4" H x 2.4" Diameter Cyanoacrylate Adhesives 9835 Luer-Slip Cap for 4 oz. and 8 oz. bottles (50 pack) 24

27 SYRINGE DISPENSING LOCTITE 30 ML MANUAL SYRINGE APPLICATOR Item Number: The Loctite 30 ml Manual Syringe Dispenser is a hand held, manually- operated dispenser for any product packaged in a standard 30 ml syringe. This dispenser provides a convenient, cost- effective method to apply product. Pistol configuration for ease of application Full-hand trigger minimizes operator fatigue Easy syringe loading Smooth dispensing Used to Dispense Any fluid in a 30 ml syringe including 25 ml net fill syringes Package Types & Sizes 30 ml syringes Viscosity Range Low to High Parts Included () 30 ml manual syringe applicator () Manual () Plunger Additional Information For Dispense Tips, see pages DISPENSING Hand Held Applicators LOCTITE 0 ML / 30 ML SYRINGE MANUAL PLUNGERS Item Numbers: 9892 and 9893 The Loctite 0 ml Manual Plunger (item 9892) is a plastic plunger for use with 0 ml syringes (2 pack). The Loctite 30 ml Manual Plunger (item 9893) is a plastic plunger for use with 30 ml syringes (3 pack). Place the front end of the plunger into the back of the syringe. Dispense product by manually pushing the back of the plunger. Used to Dispense All approved 0 ml and 30 ml syringes, including pre-packaged syringes with a 25 ml fill Package Types & Sizes 0 ml and 30 ml syringes Viscosity Range Low to High Additional Information For Syringe Accessories, see page 83. TWO-PART DISPENSING LOCTITE 50 ML DUAL CARTRIDGE MANUAL APPLICATORS Item Numbers: and The Loctite 50 ml Dual Cartridge Manual Applicators are hand held, manually- operated meter mix dispensers. These dispensers provide a convenient, cost- effective method to apply product with minimal waste. Item is compatible with : and :2 mix ratio products. Optional 4: plunger (item ) and 0: plunger (item ) are also available for standard cartridges. Item is used exclusively for products packaged in 0: S- 50 cartridges. Item Item Item Number Used to Dispense Two-Component Epoxies, Urethanes, Methacrylates Package Types & Sizes 50 ml dual manual cartridge S-50 cartridge Viscosity Range Low to High Mix Ratios : / 2: / 4: / 0: 0: Parts Included Additional Information Additional Accessories Sold Separately Replacement Plungers () 50 ml Dual Cartridge Manual Applicator () : Plunger () 2: Plunger () Manual () 50 ml, 0:-S Cartridge Manual Applicator () 0:-S Plunger For Additional Static Mix Nozzles and Accessories, see page : 4: Plunger : 0: Plunger : : Ratio : 2: Ratio Mix Nozzle available : 0:-S Mix Nozzle : 0: Ratio 25

28 DISPENSING Hand Held Applicators LOCTITE 50 ML DUAL CARTRIDGE PNEUMATIC APPLICATOR Item Number: The Loctite 50 ml Dual Cartridge Pneumatic Applicator (item 97042) is a hand held, pneumaticallyoperated dispenser. It provides a convenient, cost- effective method for applying two-part adhesive products with minimal effort and waste. The applicator can accept various 50 ml dual cartridge designs for both :, 2: and 0: mix ratios. Lightweight, well balanced design for easy use Pneumatic assist assures reduced operator fatigue and consistent adhesive application Integrated air pressure regulator Conveniently positioned thumb wheel with 5 pressure adjustments to control dispense rate Quick acting trigger insures precise bead control and minimizes product waste Versatile cartridge holder accepts dual 50 ml cartridges with :, 2: and 0: ratios Pneumatic air pressure is applied by pulling the trigger switch. This causes the dual pistons to move forward, discharging both adhesive components of the cartridge at the same rate. The adhesive is mixed as it travels through a static mix nozzle (available separately) to the working surface. The rate of adhesive application can be adjusted by changing the air pressure using the 5-position thumb wheel below the trigger. Dimensions 4.0" L x 7.6" H x 2.4" D (292 mm L x 9 mm H x 58 mm D) Weight.6 lbs. (725 g) Air Supply Air Supply Fitting Used to Dispense Package Types & Sizes 30 to 75 psi 4" NPT male Two-Component Epoxies, Urethanes, Methacrylates 50 ml dual cartridge Parts Included () 50 ml Dual Cartridge Pneumatic Applicator () Manual Viscosity Range Low to High Mix Ratios : / 2: Additional Information For Static Mix Nozzles and Accessories, see page 82. LOCTITE CAULKING GUN CONVERSION KITS FOR 50 ML CARTRIDGES Item Numbers: and 9845 The Loctite Caulking Gun Converters provide an inexpensive means of converting a household caulking gun into a hand held meter mix dispenser. Simply insert the converter into a household caulking gun, and you are ready to go. An ideal approach for the occasional user of :, 2: and 0: ratio two-part adhesives. Order Item for : or 2: ratio adhesives. Order Item 9845 for 0: ratio adhesives. Not recommended for high demand or production line applications. Household caulking gun not sold by Henkel. Viscosity Range Item Low to High Mix Ratios : / 2: / 0: Used to Dispense Package Types & Sizes Parts Included Item 9845 Two-Component Epoxies, Urethanes, Methacrylates 98466: () Instruction Sheet () Caulking Gun Converter () : Ratio Plunger () 2: Ratio Plunger (2) 50 ml Static Mix Nozzles (:, 2:) 50 ml dual cartridge 9845: () Caulking Gun Converter () 0: Ratio Plunger () Instruction Sheet (2) 50 ml Static Mix Nozzles (0:) Additional Information For Static Mix Nozzles and Accessories, see page

29 LOCTITE 200 ML / 400 ML DUAL CARTRIDGE MANUAL APPLICATORS Item Numbers: , and The Loctite 200 ml and 400 ml Dual Cartridge Manual Applicators are hand held, manually-operated meter mix dispensers. Ideally suited for production line applications, these applicators provide a convenient, cost-effective method of applying product with minimal waste. These applicators are available for :, 2: and 0: mix ratio products. A converter kit is also available for the 400 ml applicator to accommodate 4: mix ratio products (see part numbers below). Mix nozzles are sold separately. List of Applicators Loctite 200 ml Dual Cartridge Manual Applicator, : and 2: ratios Loctite 400 ml Dual Cartridge Manual Applicator, : and 2: ratios Loctite 400 ml Dual Cartridge Manual Applicator, 0: ratio Item Number Viscosity Range High to Paste Mix Ratios : / 2: : / 2: 0: Used to Dispense Package Types & Sizes Additional Information Two-Component Epoxies, Urethanes, Methacrylates 200 ml dual cartridge 400 ml dual cartridge 400 ml dual cartridge For Static Mix Nozzles and Accessories, see page 82. Additional Accessories Sold Separately 9842 Loctite 4: Conversion Kit DISPENSING Hand Held Applicators LOCTITE 200 ML / 400 ML DUAL CARTRIDGE PNEUMATIC APPLICATORS Item Numbers: , and The Loctite 200 ml and 400 ml Dual Cartridge Pneumatic Applicators are hand held, pneumatically-operated meter mix dispensers. Ideally suited for production line applications, these applicators provide a convenient, cost-effective method for applying product with minimal waste. The adjustable dispense rate is set via the integral air pressure regulator. The applicators are available for :, 2: and 0: mix ratio products. A converter kit is also available for the 400 ml applicator to accommodate 4: mix ratio products (see part numbers below). Mix nozzles are sold separately. List of Applicators Loctite 200 ml Dual Cartridge Pneumatic Applicator, : and 2: ratios Loctite 400 ml Dual Cartridge Pneumatic Applicator, : and 2: ratios Loctite 400 ml Dual Cartridge Pneumatic Applicator, 0: ratio Item Number Air Pressure Supply Viscosity Range 25 psi (8.5 bar) maximum High to Paste Mix Ratios : / 2: : / 2: 0: Adhesive Components Used to Dispense Package Types & Sizes Two-Component Epoxies, Urethanes, Methacrylates 200 ml dual cartridge 400 ml dual cartridge 400 ml dual cartridge Additional Information For Static Mix Nozzles and Accessories, see page 82. Additional Accessories Sold Separately Loctite 4: Conversion Kit 27

30 Hand Held Applicators DISPENSING LOCTITE UNIVERSAL METAL DISPENSER Item Number: The Loctite Universal Metal Dispenser is a hand held, manually- operated dispenser designed for use with two-part adhesives packaged in 200 ml and 400 ml dual cartridges. The dispenser is capable of handling cartridges with :, 2:, 4: and 0: mix ratios. This tool is ideally suited for users with a need to occasionally dispense an assortment of mix ratios or package sizes. Mix nozzles are sold separately. Accepts 200 ml and 400 ml two- component cartridges Mix ratios of :, 2:, 4:, and 0: Interchangeable plunger buttons allow application of all mix ratios Dispenses low, medium, and high viscosity materials Depress the thumb lever on the back of the dispenser and pull the plunger back. Insert the cartridge, equipped with a static mix nozzle, and push the plunger forward until it is seated onto the cartridge. Dispense product by squeezing the trigger. Dispense ratios are varied by changing the plunger buttons supplied with the tool. Viscosity Range High to Paste Adhesive Components 2 Used to Dispense Two-Component Epoxies, Urethanes, Methacrylates Package Types & Sizes 200 ml and 400 ml dual cartridges Additional Information For Static Mix Nozzles and Accessories, see page 82. LOCTITE FIXMASTER RAPID RUBBER REPAIR DISPENSER Item Number: The Loctite Fixmaster Rapid Rubber Repair Dispenser is a hand held, manually- operated dispenser designed specifically for use with Loctite Fixmaster Rapid Rubber Repair, a two- part adhesive packaged in 400 ml cartridges. Wide front opening to fit specific cartridges Dedicated : mix ratio 200 ml x 200 ml dual cartridges Bottom support straps provide secure cartridge location within frame Ability to handle high viscosity materials Depress the thumb lever on the back of the dispenser and pull the plungers back. Insert the cartridge, equipped with a static mix nozzle, and push the plungers forward until they seat onto the cartridge. Dispense product by squeezing the trigger. Viscosity Range Medium to High Adhesive Components 2 Used to Dispense Loctite Fixmaster Rapid Rubber Repair Urethanes Package Types & Sizes 400 ml dual cartridges Additional Information For Static Mix Nozzles and Accessories, see page

31 CARTRIDGE DISPENSING LOCTITE 300 ML PNEUMATIC CARTRIDGE DISPENSER Item Number: The Loctite 300 ml Pneumatic Cartridge Dispenser is a hand held unit for dispensing product packaged in 300 ml cartridges and 250 ml squeeze tubes. It is especially useful for applications where larger systems and packages, such as a 5 gallon pail pump system, are not desirable. Integrated pressure regulator Quick pressure relief Use with 300 ml cartridges and 250 ml squeeze tubes Typical Applications: The rate of application is controlled by the integrated air pressure regulator. The amount of product dispensed is controlled by the trigger. Air Inputs 25 psi max with 300 ml cartridge 22 psi max with 250 ml squeeze tubes Pneumatic Connection Thread Diameter: R 4" Pneumatic Hose: Inner Diameter - 6 mm Dimensions 8.0" H x 3.5" L x.5" D Weight.8 lbs. (800 g) Used to Dispense Gel Cyanoacrylates, Structural Acrylics, Silicones, Anaerobic Flange Sealants Package Types & Sizes 300 ml cartridges Parts Included () 300 ml Pneumatic Cartridge Dispenser (2) Spare Membranes () Manual Additional Information For Cartridge Accessories, see page 8. Additional Accessories Sold Separately Adapter for 250 ml Squeeze Tubes DISPENSING Hand Held Applicators LOCTITE FOLDABLE 300 ML CARTRIDGE APPLICATOR Item Number: The Loctite Foldable 300 ml Cartridge Applicator is a hand held, manually- operated dispenser designed for all products packaged in 300 ml cartridges. It has an innovative folding trigger assembly that allows it to be stored in less space or carried more conveniently than conventional household caulking guns. Foldable trigger assembly for easy storage Durable frame for heavy duty use Dispenses high viscosity silicones and lubricants with ease Dimensions Open: 8.0" H x 3.0" L x 2.5" D Trigger Folded: 4.0" H x 3.0" L x 2.5" D Weight 0.6 lbs. (275 g) Used to Dispense Gel Cyanoacrylates, Structural Acrylics, Silicones, Anaerobic Flange Sealants, Lubricants Package Types & Sizes 300 ml cartridges Parts Included () Foldable Cartridge Applicator () Manual Additional Information For Cartridge Accessories, see page 8. LOCTITE 300 ML PNEUMATIC CARTRIDGE DISPENSER RETAINER Item Number: 9839A The Loctite 300 ml Pneumatic Cartridge Dispensing Retainer provides controlled, pressure/time dispensing of adhesives in 300 ml cartridges when used in conjunction with the Loctite Analog Syringe Dispenser (item 9847), Loctite Precision Syringe Dispenser (item 97006), or the Loctite Foot Pedal Dispensers (items and 98050). Pressures up to 60 psi can be obtained to effectively dispense low to medium viscosity products and thixotropic gels. Quick twist open/close cap Use with 300 ml cartridges Air Inputs 70 psi max with 300 ml cartridge 22 psi max with 250 ml squeeze tubes Product Viscosity Low to Medium Dimensions 0.0" L x 2.5" D Weight.8 lbs. (800 g) Used to Dispense Gel Cyanoacrylates, Anaerobic Gasketing, Light Cure/Acrylics, Silicones Package Types & Sizes 300 ml cartridges Parts Included () 300 ml Pneumatic Cartridge Dispensing Retainer and Cap Additional Information For Cartridge Accessories, see page 8. 29

32 DISPENSING Two-Part Volumetric Dispensing Dual Cartridge Systems Two-Part Volumetric Dispensing Loctite Posi-Link Dispense System for Dual Cartridges When you need high precision dispensing from your prepackaged dual cartridge adhesive, the Loctite Posi-Link Dispense System is the solution. This system offers dispensing accuracy well beyond any pneumatic cartridge dispenser down to 0.00 ml drop size. This system specifically excels at eliminating dispense variability due to continuously changing viscosity (curing) in the mix nozzle. It can easily be integrated into any automated process and provide process feedback to a plant PLC. Select your system based on cartridge size and adhesive ratio requirements. You can choose 50, 200 or 400 ml packages for any :, 2: or 0: ratio product. the of Volumetric Control The END of wetted components AGE LOCTITE POSI-LINK CONTROLLER Item Number: Provides all operator interface and control signals to actuator. COMPLETE LOCTITE POSI-LINK DUAL CARTRIDGE SYSTEM For 50 ml Dual Cartridges: Controller + Actuator + Nest For 200/400 ml Dual Cartridges: Controller + Actuator + Nest + Pinch Tube (Each Item Sold Separately) Dose selection by volume Easy programming controller, with storage capacity for 25 user defined programs, reduces adhesive set-up waste Smallest footprint on the market to conserve benchtop space Automatic cartridge engagement to ensure easy and error-free cartridge changeover Adhesive level monitoring with low level visual and digital outputs Fault detection with visual and digital outputs for clogged nozzles, loss of pressure, and system faults In- cycle visual and digital outputs Foot switch, finger switch or PLC remote start activation LOCTITE POSI-LINK ACTUATORS Item Numbers: See chart Provides adhesive dispensing by effecting incremental movements of dual pistons and displacing programmable qualities of adhesive within the cartridge regardless of viscosity changes in the mix nozzle. PRODUCT Item Number Dual Cartridge Size Loctite Posi-Link 0-50 Actuator 98379* 50 ml Loctite Posi-Link Actuator , 400 ml * See pages 9-0 for use with syringes. Flexible orientation in any position Easily fits below an industrial workbench or wall mounts with brackets supplied to conserve benchtop space Lightweight remote dispense head has a positive link to actuator via a 7 foot tether, allowing ergonomic hand held dispensing or mounting directly on robotic arms Easily attaches to the dual cartridge nests (sold separately) to accommodate alternate cartridge barrel sizes Mechanically linked dual plungers guarantee proper ratios are achieved Positive shut- off pinch tube available, which directly attaches to the mix nozzle, eliminating dripping 30

33 LOCTITE POSI-LINK 50 ML DUAL CARTRIDGE NESTS Item Number: See chart Connects the actuator to the dual cartridge. Dual Cartridge Nest No tool cartridge changeover No contact with adhesive. Disposable syringes are the only component in contact with the adhesive Loctite Posi-Link Dual Cartridge Nest Selection LOCTITE POSI-LINK 200/400 ML DUAL CARTRIDGES NESTS Item Number: See chart Connects the actuator to the dual cartridge. : / 2: 50 ml Cartridge 0: 50 ml Cartridge : / 2: 200 ml Cartridge : / 2: 400 ml Cartridge 0: 400 ml Cartridge USED WITH DISPENSING Two-Part Volumetric Dispensing Dual Cartridge Systems N/A N/A N/A N/A N/A Loctite Posi-Link 0-50 Actuator Loctite Posi-Link Actuator A disposable dual cartridge is effectively used as a dual metering piston/cylinder. Because the individual chambers of a dual cartridge are of a known and constant diameter, a given incremental measurement of the dual pistons will displace a known volume of adhesive within each chamber at an exact ratio. This dual cartridge system functions identically to a Loctite Posi-Link Syringe System, except that it has 2 plungers within the dispense head. These plungers simultaneously act on 2 chambers within the dual cartridge. See Functionality Diagram on page 0. LOCTITE PINCH TUBE VALVE Item Number: 974 Valve attaches directly to the end of the square mix nozzle Provides positive no-drip shut off, using disposable pinch tube elements FOR 50 ML DUAL CARTRIDGES: OPTIONAL: 974 Valve pack Replacement Tube Inserts Solenoid Valve FOR 200/400 ML DUAL CARTRIDGES: REQUIRED: 974 Valve pack Replacement Tube Inserts (9867 Solenoid Valve included with actuator) Loctite Posi-Link 0-50 System, Integrated Robotic Solution using a 50 ml dual cartridge, and showing wall-mounted actuator. PRODUCT Loctite Posi-Link Controller Loctite Posi-Link 0-50 Actuator Loctite Posi-Link Actuator Item Number Power Source 9' communication cable 00/240 VAC; 47/60 Hz 00/240 VAC; 47/60 Hz Dimensions 5.375" H x 6" D x 6" W 34" H x 4" D x 5" W 34" H x 4" D x 5" W Total Weight 2 lbs. 3 lbs. 20 lbs. Dispense Head Weight (Includes Nest and N/A 2.0 lbs. 0.0 lbs. Pinch Tube Valve) Air Supply N/A 40 to 00 psi 40 to 00 psi Posi-Link Electro/Hydraulic N/A 7 feet 7 feet Tether Minimum Dispense Volume N/A 0.00 ml 0.0 ml Maximum Dispense Rate Maximum Cycle Rate Used to Dispense N/A 0.4 ml/second.0 ml/second N/A cycle per second cycle per second N/A Parts Included () Loctite Posi-Link Controller () Foot Switch Additional Information All dual 50 ml cartridge : / 2: / 0: ratio adhesives All dual 200 or 400 ml cartridge : / 2: / 0: ratio adhesives () Loctite Posi-Link Actuator () 9' Controller/Actuator Signal Cord () 0 Power Cord () Air Inlet Pressure Regulator Gauge () Wall or Table Mounting Bracket () Instruction Manual For Spare Parts and Accessories, see pages For Static Mix Nozzles and Accessories, see page 82. 3

34 DISPENSING Two-Part Volumetric Dispensing Two-Part Volumetric Dispensing Meter Mix Systems Loctite Meter Mix Systems When your Loctite two- part adhesive application takes on a larger dimension, Henkel has the two- part volumetric dispensing solution with our high precision Loctite Meter Mix Dispense Systems. You can choose either fixed and variable ratio units for any of our featured systems and, together with a wide selection of reservoir systems, hoses, valves and other accessories, customize your system to meet your application requirements. NEW NEW Loctite DuraPump PRODUCT Programmable Meter Mix System MACHINE RATIO CAPABILITIES/ITEM NUMBERS See page 33 for Fixed more information Loctite DuraPump Pneumatic Meter Mix System Loctite Meter Mix 000 Dispense System Loctite Meter Mix 2000 Dispense System Loctite Meter Mix 3000 Dispense System See page 34 for : Low Flow more information : High Fow Variable N/A N/A 98890: Low Flow : High Flow PERFORMANCE SPECIFICATIONS Dispense Range 0.40 cc to 28 cc 0.5 cc to 25 cc (Fixed), 0.5 cc to 2.37 cc (Variable) Cycle Rate Up to 20 per minute Up to 30 per minute Mix Ratio Range by Volume : to 0.0: : to 9.76: (Fixed), : to 4.56: (Variable) Maximum Product Feed Pressure 2000 psi 60 psi WETTED COMPONENT MAKEUP Abrasion Resistant Pumps Standard Standard Optional Optional Optional Mild Steel Pumps Not Required Not Required Standard Standard Standard Inert Pumps Standard Standard Optional Optional Optional DISPENSE VALVES Mix Manifold (accepts mix nozzle directly) Standard Standard N/A N/A N/A Hand Held Valve with Trigger Pistol Grip Optional Optional Optional Optional Optional Hand Held Valve with Lever Actuation N/A N/A Optional Optional Optional Adjustable Boom Mounted Valve N/A N/A N/A Optional Optional SHOT CONTROL CAPABILITIES Manual/Operator Controlled Shot Standard Standard Standard Standard Standard Mechanically Adjusted Limit Switch Shot Control N/A Standard N/A Standard Standard Pre-Programmed Electronic Shot Size Control Standard N/A N/A N/A Standard Multiple Pre-Programmed Shot Size Control Standard N/A N/A N/A Standard Touchscreen Machine Controls Standard N/A N/A N/A Standard OTHER MACHINE FEATURES Feed Accumulators for Bulk Package Pressure Feed Not Required Not Required Optional Optional Optional Maintenance Totalizer Standard N/A N/A N/A Standard Low/High Level Sensing Capable Optional Low Level Only N/A N/A N/A Standard Supervisor Machine Lock-Out Standard N/A N/A N/A Standard Pneumatically Adjustable Flow Control Standard Standard Standard Standard Standard Auto-Purge Capable Standard N/A N/A N/A Standard Foot Switch Controlled Standard Standard N/A Standard Standard 32

35 DISPENSING Two-Part Volumetric Dispensing Meter Mix Systems LOCTITE DURAPUMP PROGRAMMABLE METER MIX SYSTEM The Loctite DuraPump Meter Mix Systems offer superior operating performance and durability for a wide range of two component adhesive chemistries up to 0: ratios. These programmable models provide convenient touch screen digital control for shot size, choice of 3 operating modes, and can easily be integrated with a PLC. Its innovative rod displacement pump design insures excellent shot repeatability, low wear, and allows direct connection to high pressure feed systems. A static mix nozzle can also be mounted directly on the integrated mixing manifold, eliminating the need for a dispense valve in many applications. Optional reservoirs, level controls, hoses, and valves are also available to complete your specific process requirements. Programmable Loctite DuraPump Fixed Ratio Systems Item Number Mix Ratio Shot Size Range : 0.4 to 28 ml : 0.4 to 2 ml : 0.4 to 8 ml : 0.4 to 5.5 ml Custom* Will vary based on ratio selected * Custom ratios available from : up to 9.99:. NEW Includes 3 modes, including an incremental shot mode, where shots can be set and dispensed without recharging No requirement for pump phasing on start-ups; just start up and go Direct flow shut off, no check valves to repair or replace Accepts external feed systems up to 2000 psi without extraneous accumulators Superior pump wear life, especially well suited for highly filled materials Mixing manifold discharge accepts mix nozzles directly, Utilities eliminating the need for a valve in many applications Available with optional low level sensors Dimensions The Loctite DuraPump Programmable Meter Mix Systems accurately meter dual liquid or semi- solid materials throughout a wide range of viscosities and ratios. The Loctite DuraPump assembly ensures high precision volumetric displacement at the selected ratio. Shot size is controlled by a touch screen input. Both liquids move simultaneously and separately into a mixing manifold. A static mix nozzle is attached to the manifold for effective mixing of two components prior to being applied. Weight Dispense Range/Cycle Cycle Rate Used to Dispense Package Types Parts Included Additional Information Electric: 0/250 VAC; Hz Pneumatic: 80-0 psi 27" H x 2.5" W x 2.5" D 80 lbs. 0.4 to 28 ml (ratio dependent) see ratio chart Up to 20/minute Two-Part Epoxies, Two-Part Acrylics, Two-Part Polyurethanes Any, excluding dual cartridges ) Loctite DuraPump Programmable Meter Mix () Foot Switch () Night Cap () Ratio Cap Feed system options and accessories are sold separately. See page

36 Two-Part Volumetric Dispensing Meter Mix Systems DISPENSING LOCTITE DURAPUMP PNEUMATIC METER MIX SYSTEM The Loctite DuraPump Pneumatic Meter Mix Systems offer superior operating performance and durability for a wide range of two component adhesive chemistries, including MMA, up to 0: ratios. All of the pneumatic models provide operator shot size control with pneumatic foot pedal or optional hand held trigger controlled dispense valve. Its innovative rod displacement pump design insures excellent shot repeatability, low wear, and allows direct connection to high pressure feed systems. A static mix nozzle can also be mounted directly on the integrated mixing manifold, eliminating the need for a dispense valve in many applications. Optional reservoirs, level controls, hoses and valves are also available to complete your specific process requirements. NEW Pneumatic Loctite DuraPump Fixed Ratio Systems Item Number Mix Ratio Shot Size Range : 0.4 to 28 ml : 0.4 to 2 ml : 0.4 to 8 ml : 0.4 to 5.5 ml Custom* Will vary based on ratio selected For MMA Chemistry : 0.4 to 28 ml : 0.4 to 5.5 ml Custom* Will vary based on ratio selected * Custom ratios available from : up to 9.99:. No electrical power required. Ideal for flammable adhesives (MMAs) and remote locations where only compressed air is available No requirement for pump phasing on start-ups; just start up and go Direct flow shut off, no check valves to repair or replace Systems accept external feed systems up to 2000 psi without extraneous accumulators Superior pump wear life, especially well suited for highly filled materials Mixing manifold discharge accepts mixe nozzles directly, Utilities eliminating the need for a valve in many applications Dimensions The Loctite DuraPump Pneumatic Meter Mix Systems accurately meter dual liquid or semi- solid materials throughout a wide range of viscosities and ratios. The Loctite DuraPump assembly ensures high precision volumetric displacement at the selected ratio. Shot size is controlled by mechanical limit switches. Both liquids move simultaneously and separately into a mixing manifold. A static mixer is attached to the manifold for effective mixing of two components prior to being applied. Weight Dispense Range/Cycle Cycle Rate Used to Dispense Package Types Parts Included Additional Information Pneumatic: 80-0 psi 27.0" H x 2.5" W x 2.5" D 80 lbs. 0.4 to 28 ml (ratio dependent) see ratio chart Up to 20/minute Two-Part MMAs, Two-Part Epoxies, Two-Part Acrylics, Two-Part Polyurethanes Any, excluding dual cartridges ) Loctite DuraPump Pneumatic Meter Mix () Foot Switch () Night Cap () Ratio Cap Feed system options and accessories are sold separately. See page

37 DISPENSING Two-Part Volumetric Dispensing Meter Mix Systems LOCTITE METER MIX 000 DISPENSE SYSTEM OPERATOR TRIGGER CONTROL Item Numbers: , 98890, and The Loctite Meter Mix 000 Dispense Systems are versatile dispensing systems for two-part adhesive chemistries and incorporate a variety of feed system options. Available in fixed or variable ratio, the compact design of the systems allows benchtop dispensing. These machines come standard to accept a hand held dispense valve (sold separately). Flow rate is adjustable through the use of a pressure regulator. See technical specifications for shot size and mix ratio ranges. Variable mix ratio capability Ratio check valves Adjustable flow control Mild steel or abrasion resistance pumps available Operator controlled shot size The Loctite Meter Mix 000 Dispense Systems accurately meter dual liquid and semi-solid materials throughout a wide range of viscosities and ratios. They contain two high precision, volumetric displacement pump assemblies. Selectable paired pump diameters determine the ratio for a fixed system. The variable ratio unit utilizes a pneumatic cylinder to adjust a lever- beam drive link to automatically change ratio requirements. Dispensing is controlled using a pneumatically controlled valve to open (sold separately). Shot size is controlled using a manual vernier selector switch and 4- digit reference. Both liquids move simultaneously through two dispensing hoses, a dispense valve and mixing chamber/static mixer that provide the effective mixing of the two components just prior to being applied. Fixed Variable Utilities Dimensions Weight Dispense Range/Cycle Cycle Rate Mix Ratio Range by Volume Used to Dispense Low Flow System 000L High Flow System 000H Low Flow System 000L High Flow System 000H Pneumatic: 80 to 00 psi 20.0" H x 5.0" W x 28.0" D 75 to 00 lbs. FIXED 0.5 cc to 25 cc VARIABLE 0.5 cc to 2.37 cc Up to 30 or more per minute, depending on material viscosity, hose sizes, and mixer type FIXED : to 9.76: VARIABLE : to 4.56: Two-Part Epoxies, Two-Part Acrylics, Two-Part Polyurethanes Package Types Cans, pails, drums, totes Parts Included () Loctite 000 Meter Mix System Choice of either 8, 0, 5, 20, 25, 30 or 35 mm pump assemblies (depends on ratio and dispense rate requirements)* () Pump Mode Off/On pneumatic selector switch (0) Static Mixers () Night Cap () Ratio Cap Additional Information **Feed system options and accessories are sold separately and can be found on pages *See pages 4-42 to determine pump diameters required for your application. Additional Accessories Sold Separately** Material reservoirs Dispense valves Abrasive resistant Level sensors Follower plates wetted components Reservoir heaters Desiccant dryers All 36 stainless steel Hoses various sizes Lock down lid wetted components and lengths with agitator for MMAs 35

38 Two-Part Volumetric Dispensing Meter Mix Systems DISPENSING LOCTITE METER MIX 2000 DISPENSE SYSTEM MANUAL SHOT SIZE Item Numbers: and The Loctite Meter Mix 2000 Dispense Systems are versatile dispensing systems for two-part adhesive chemistries and incorporate a variety of feed system options. Available in fixed or variable ratio, the compact design of the systems allows benchtop dispensing along with a variety of feed systems and package sizes. These machines are capable of controlled shot size, dispensing through a pre- set mechanical stroke adjustment. Flow rate is also variable through the use of a pressure regulator. See technical specifications for shot size and mix ratio ranges. Variable mix ratio capability Manual vernier shot size selector with a 4- digit reference gauge Adjustable flow control Mild steel or abrasion resistant pumps available Emergency stop palm button Three position pump mode selector Three position dispense selector Foot switch activation The Loctite Meter Mix 2000 Dispense Systems accurately meter dual liquid and semi-solid materials throughout a wide range of viscosities and ratios. They contain two high precision volumetric displacement pump assemblies. Selectable paired pump diameters determine the ratio for a fixed system. The variable ratio unit utilizes a pneumatic cylinder to adjust a lever- beam drive link to automatically change ratio requirements. Shot size is controlled using a manual vernier selector switch and 4- digit reference. Both liquids move simultaneously through two dispensing hoses, a dispense valve and mixing chamber/ static mixer that provide the effective mixing of the two components just prior to being applied. Item Numbers Fixed Variable Utilities Pneumatic 80 to 0 psi Electric 20 VAC Dimensions 20.0" H x 5.0" W x 28.0" D Weight 75 to 00 lbs. Dispense Range/Cycle FIXED 0.5 cc to 25 cc VARIABLE 0.5 cc to 2.37 cc Cycle Rate Up to 30 or more per minute, depending on material viscosity, hose sizes, and mixer type Mix Ratio Range by Volume FIXED : to 9.76: VARIABLE : to 4.56: Used to Dispense Two-Part Epoxies, Two-Part Acrylics, Two-Part Polyurethanes Package Types Cans, pails, drums, totes Parts Included () Loctite 2000 Meter Mix System Choice of either 8 mm, 0 mm, 5 mm, 20 mm or 25 mm pump assemblies (depends on ratio and dispense rate requirements)* () Night Cap () Ratio Cap (0) Static Mixers Additional Information **Feed system options and accessories are sold separately and can be found on page *See pages 4-42 to determine pump diameters required for your application. Additional Accessories Sold Separately** Material reservoirs Dispense valves Follower plates Lock down lid with agitator Reservoir heaters Desiccant dryers Hoses various sizes Abrasive resistant Mounted trigger assembly and lengths wetted components for dispense valve 36

39 DISPENSING Two-Part Volumetric Dispensing Meter Mix Systems LOCTITE METER MIX 3000 DISPENSE SYSTEM PROGRAMMABLE SHOT SIZE Item Numbers: and The Loctite Meter Mix 3000 Dispense Systems are versatile dispensing systems for two- part adhesive chemistries and incorporate a variety of feed system options. Available in fixed or variable ratio, the systems offer programmable shot size and integrated PLC controls with convenient touch screen capability. These units come standard with mild steel pump components with optional abrasion resistant or 304 stainless steel. See technical specifications for shot size and mix ratio ranges for both units. Fixed and variable mix ratio capability Programmable shot size selection from touch screen Ratio check valves Adjustable flow control Mild steel or abrasion resistant pumps available 4.5" W x 3.4" H monochrome touch screen and PLC Cycle totalizer Maintenance totalizer Automatic purge controller Emergency stop palm button Foot switch activation The Loctite Meter Mix 3000 Dispense Systems accurately meter dual liquid and semi-solid materials throughout a wide range of viscosities and ratios. They contain two high precision volumetric displacement pump assemblies. Selectable paired pump diameters determine the ratio for a fixed system. The variable ratio unit utilizes a pneumatic cylinder to adjust a lever-beam drive link to automatically change ratio requirements. Shot size is controlled using a PLC interface for stroke adjustment. Both liquids move simultaneously through two dispensing hoses and a dispense valve and mixing chamber/static mixer that provide the effective mixing of the two components just prior to being applied. Item Numbers Fixed Variable Utilities Pneumatic 80 to 5 psi Electric 20 VAC Dimensions 20.0" H x 5.0" W x 28.0" D Weight 75 to 00 lbs. Dispense Range/Cycle FIXED 0.5 cc to 25 cc VARIABLE 0.5 cc to 2.37 cc Cycle Rate Up to 30 or more per minute, depending on material viscosity, hose sizes, and mixer type Mix Ratio Range by Volume FIXED : to 9.76: VARIABLE : to 4.56: Used to Dispense Two-Part Epoxies, Two-Part Acrylics, Two-Part Polyurethanes Package Types Cans, pails, drums, totes Parts Included () Loctite 3000 Meter Mix System Choice of either 8 mm, 0 mm, 5 mm, 20 mm or 25 mm pump assemblies (depends on ratio and dispense rate requirements)* () Night Cap () Ratio Cap (0) Static Mixers Additional Information **Feed system options and accessories are sold separately and can be found on pages *See pages 4-42 to determine pump diameters required for your application. Additional Accessories Sold Separately** Material reservoirs Dispense valves Follower plates Lock down lid with agitator Reservoir heaters Desiccant dryers Hoses various sizes Abrasive resistant Mounted trigger assembly and lengths wetted components for dispense valve 37

40 DISPENSING Loctite DuraPump Selector Guide Adhesive Feed Options Two-Part Volumetric Dispensing Meter Mix Systems Gravity Tanks (< 7,000 cps) PE Tank 36SS Tank Dispense Valve General Purpose MMA Pistol Grip Option Loctite DuraPump Meter Mix System Hose Options Pressure Reservoirs (7,000 to 70,000 cps) Various Lengths and Diameters Pail Pumps ( > 70,000 cps) Mix Nozzle Manifold Direct Mix Nozzle Attachment See page 39 for Loctite DuraPump Feed and Dispensing Options Loctite Meter Mix 000, 2000 and 3000 Dispense Systems Accessory- Option Selector Guide Dispense MMD Dispense Valve Valve Control Options Hose Configuration 2 Stainless Steel : Stainless Steel 0: Abrasion Resistant : Abrasion Resistant 0: Hand Held Valve Lever Actuated Valve Foot Pedal Actuated Length Diameter Pumps Pump Seals 3 Pump Sizes Pump Construction Material 4 Viton EP Sized for Dispense Volume Mild Steel Stainless Steel Abrasion Resistant System Options Heat Agitation 5 Precision Flow Vacuum System PLC Backup Control Drive Level Sensing Feed Package Gravity Feed Pressure Feed 6 Reservoir Materials Reservoir Size Mild Steel Stainless Steel Polyethylene 5 or 7.5 L 5 Gallon 55 Gallon Stainless steel is the standard material. Abrasion resistant should be used when abrasive fillers are present. Mix ratios from : to 5: require the : valve, mix ratios >5: require the 0: valve. 2 Viscosity and mix ratio are dependent. High mix ratios and viscosities = larger diameters, Low mix ratios and viscosities = smaller diameters. 3 Viton for epoxy resin, urethane resin and hardener, and silicone resin and hardener. EP for epoxy hardener and MMA resin and hardener. 4 Mild steel is standard. Stainless should be used for materials that are incompatible with mild steel. Abrasion resistant should be used when abrasive fillers are present. 5 Required for highly filled materials. Mixing suspends the filler in the fluid. 6 Require the use of an accumulator. Can be used for drums, pails, or reservoirs. 38

41 Loctite Brand Meter Mix System Options and Accessories All items sold separately, except where noted. Loctite DuraPump Models PRODUCT Item Number DURAPUMP DISPENSE VALVES Optional Description Dispense Valve General Purpose (All ratios) Dispense Valve MMA (All Ratios) 0566 Pistol Grip with Pneumatic Trigger (Converts Dispense Valve into a Hand-held Tool) DURAPUMP HOSE KIT 2 required for each dispense valve Hose for Dispense Valve 3 8" x 24" General Purpose Hose for Dispense Valve 3 8" x 96" General Purpose Hose for Dispense Valve 3 8" x 44" General Purpose Hose for Dispense Valve 3 8" x 24" MMA Hose for Dispense Valve 3 8" x 96" MMA Hose for Dispense Valve 3 8" x 44" MMA DuraPump Heated Hose Option 48" DuraPump Heated Hose Option 96" DuraPump Heated Hose Option 44" All Loctite DuraPump hose kits come complete with 2 fittings for connection to the DuraPump System and Dispense Valve. DURAPUMP RESERVOIR OPTIONS SHOWN: 2 Poly Tanks mounted on Dual Tank Stand L Poly Gravity Tank with Cover (Requires 0565) 7 L Stainless Steel Gravity Tank with Cover (Requires 0565) Dual Tank Stand ( Required for each pair pf Gravity Tanks) Disposable Desiccant Air Dryer Option DURAPUMP CONTROL OPTIONS Follower Plate with Handle (For Stainless Steel Tank Only) Agitator Assembly (For Stainless Steel Tank Only) Tank Heater and Controls Option (For Stainless Steel Tank Only) Low Level Sensing Option Stainless Steel Tank (Programmable DuraPump Only) Low Level Sensing Option Poly Tank (Programmable DuraPump Only) Hose Heat Controller For or 2 Heated Hoses Precision Hydraulic Flow Controller MMD 000, 2000 and 3000 Models Item PRODUCT Number DISPENSE VALVES HOSES All Braided Stainless Steel Description Pistol Grip, Pneumatic Switch Option, (MMD 000) Dispense Valve : Nose, Abrasion Resistant Dispense Valve : Nose, Stainless Steel Dispense Valve 0: Nose, Stainless Steel Dispense Valve 0: Nose, Abrasion Resistant Pistol Grip, Electric Switch Option, (MMD 2000, 3000) Lever Actuated, 4" Pneumatic Switch Option Lever Actuated, 3 8" Pneumatic Switch Option Lever Actuated, 3 8" Electric Switch Option VALVE MOUNTING BOOMS Valve Mounting Boom 5 or 7 L Tanks Valve Mounting Boom 5 gallon Tanks MMD Hose 3 6" x 24", Stainless Steel Fittings MMD Hose 3 6" x 72", Stainless Steel Fittings MMD Hose 3 6" x 20", Stainless Steel Fittings MMD Hose 4" x 24", Mild Steel Fittings MMD Hose 4" x 72", Mild Steel Fittings MMD Hose 4" x 20", Mild Steel Fittings MMD Hose 4" x 24", Stainless Steel Fittings MMD Hose 4" x 72", Stainless Steel Fittings MMD Hose 4" x 20", Stainless Steel Fittings MMD Hose 3 8" x 24", Mild Steel Fittings MMD Hose 3 8" x 72", Mild Steel Fittings MMD Hose 3 8" x 20", Mild Steel Fittings 9892 MMD Hose 3 8" x 24", Stainless Steel Fittings MMD Hose 3 8" x 72", Stainless Steel Fittings MMD Hose 3 8" x 20", Stainless Steel Fittings MMD Hose 2" x 24", Mild Steel Fittings MMD Hose 2" x 72", Mild Steel Fittings MMD Hose 2" x 20", Mild Steel Fittings MMD Hose 2" x 24", Stainless Steel Fittings MMD Hose 2" x 72", Stainless Steel Fittings MMD Hose 2" x 20", Stainless Steel Fittings STAINLESS STEEL 5 and 7.5 Liter Stainless Steel Reservoir Options L Stainless Steel Tank with Cover L Stainless Steel Tank with Cover L Tank High-Low & Vac. Ready Mild Steel (MMD 3000) L Tank High-Low & Vac. Ready SS (MMD 3000) Recirculation for 5 or 7.5 L Tanks Disposable Desiccant Air Dryer and Lock Down Lid Follower Plate with Handle Electric Agitator Assembly with Cover Heat Blanket (720 W) and Insulation for 5 or 7.5 L Tank Hose Heater (50 W) and Insulation for 2" or 3 8" x 2' long Low Level Sensor for one 7.5 L Tank L Tank, High-Low Sensor Ready (MMD 3000 only) High and Low Level Sensor for one 5 or 7.5 L Tank High and Low Level Sensors with Auto Refill Disposable Desiccant Air Dryer or 7.5 L Tank Vacuum Ready, Mild Steel DISPENSING Two-Part Volumetric Dispensing Meter Mix Systems 39

42 DISPENSING Loctite Brand Meter Mix Feed System Options and Accessories for Meter Mix 000, 2000 and 3000 Dispense Systems Only All items sold separately, except where noted. Two-Part Volumetric Dispensing Meter Mix Systems PRODUCT Item Number Description ACCUMULATOR FEED OPTIONS - (Accumulator Replaces the Tank on that Side) Aluminum Accumulator; High-Low Electric Controls Stainless Steel Accumulator; High-Low Electric Controls Aluminum Accumulator; High-Low Pneumatic Controls Stainless Steel Accumulator; High-Low Pneumatic Controls 5 GALLON TANK FEED OPTIONS CFM Vacuum Pump Assembly Pressure - Vacuum Tank Mild Steel Electric Agitator Tank Tank Support Stand Holds 2 Tanks Disposable Desiccant Dryer 5 gallon Nitrogen Harness Assembly Tank Nitrogen Harness Assembly 2 Tanks Polyethylene Tank Assembly Polyethylene Follower Plate Tank Air Pressure Assembly Low Level Control Sensor (MMD 3000 only) High & Low Level Control Sensors (MMD 3000 only) Pressure - Vacuum Tank Stainless Steel 9890 Pump Inlet Adapter Fitting Vacuum Valving Assembly.0", Mild Steel Vacuum Valving Assembly.0", Stainless Steel Heat Blanket Insulation 750 watts ELECTRICAL HEAT CONTROLS Electrical Enclosure and Controls for Heat Load Electrical Enclosure and Controls for 2 Heat Loads Electrical Enclosure and Controls for 3 Heat Loads Electrical Enclosure and Controls for 4 Heat Loads SYSTEM CONTROL OPTIONS Precision Flow Control Drive (MMD 3000 only) PLC Program Backup/Upgrade (MMD 3000 only) PLC Interface Cable (MMD 3000 only) Remote Operator Controls SHIPPING CRATES Shipping Crate 5 and 7.5 L Systems Shipping Crate 5 gallon Tank Systems PRODUCT PUMP MATERIAL OPTIONS RATIO CHECK VALVES Item Number PUMP PAIR CONFIGURATIONS All Mild Steel - (Standard sizes included in system pricing) Description Abrasion Resistant Pumps instead of Mild Steel 304 Stainless Steel Pumps instead of Mild Steel 3-way Stainless Steel Ratio Check Valve Upgrade mm High, 8 mm Low mm High, 0 mm Low mm High, 5 mm Low mm High, 20 mm Low mm High, 25 mm Low mm High, 8 mm Low mm High, 0 mm Low mm High, 5 mm Low mm High, 20 mm Low mm High, 25 mm Low mm High, 8 mm Low mm High, 0 mm Low mm High, 5 mm Low mm High, 20 mm Low mm High, 25 mm Low mm High, 8 mm Low mm High, 0 mm Low mm High, 5 mm Low mm High, 20 mm Low mm High, 25 mm Low mm High, 8 mm Low mm High, 0 mm Low mm High, 5 mm Low mm High, 20 mm Low mm High, 25 mm Low mm High, Custom Diameter Low mm High, Custom Diameter Low mm High, Custom Diameter Low mm High, Custom Diameter Low mm High, Custom Diameter Low mm High, Custom Diameter Low mm High, Custom Diameter Low Custom Diameter High, 8 mm Low Custom Diameter High, 0 mm Low Custom Diameter High, 5 mm Low Custom Diameter High, 20 mm Low Custom Diameter High, 25 mm Low Custom Diameter High, 30 mm Low Custom Diameter High, 35 mm Low 40

43 Meter Mix Dispensing Systems Pump Selector Guides Fixed Ratio Systems for Meter Mix 000, 2000 and 3000 Dispense Systems All Loctite brand MMD machines include two (2) standard pump sizes: 8, 0, 5, 20 and 25 mm. CHART - Fixed Ratio Pump Diameter Configuration and Corresponding Mix Ratio HIGH VOLUME PUMP (mm) LOW VOLUME PUMP (mm) Output CCs Pump sizes = WHITE; Maximum output per single pump = BLUE; Volumetric mix ratio (high volume component/low volume component) = BLACK DISPENSING Two-Part Volumetric Dispensing Meter Mix Systems SELECTION PROCESS. Determine the adhesive shot volume required per part in cubic centimeters (cc s; same as ml s), from production requirements. 2. From adhesive technical data sheet, determine the adhesive volumetric mix ratio (high volume component/low volume component). 3. Review the blue maximum outputs for a volume which is 50% to 90% of the maximum output volume of the combined pump size configuration. Be sure to combine a high volume and low volume pump for the corresponding maximum output volume of the combined pumps, see example. a. If the adhesive shot volume required is greater than that of the maximum possible output of the configurations, divide the required shot volume by the smallest number which makes the required shot volume less than the maximum possible output for that configuration. Then repeat step 4. The divisor is the number of cycles the machine must perform to meet the required shot volume, see example 2. b. Compare the maximum output volume of the combined pump configuration to the white mix ratio for that combination of pump sizes. If the corresponding mix ratio does not exactly match that of the adhesive, review the chart for other alternatives, or specify one pump from the chart, along with a Custom pump size, which will yield the exact pump configuration required for the adhesives mix ratio, see example 2 and see custom pump volume calculation example below**. EXAMPLE # FIXED RATIO STANDARD PUMP SIZES APPLY High volume = Low volume = Mix ratio = / = Per part shot size = 6 cc (6 ml) High volume pump = 5 mm Low volume pump = 5 mm Volumetric mix ratio = / Maximum pump combination output = cc (6 cc / cc) x 00% = 67% - o.k. Recommended pump configuration = 5 mm/5 mm 5 mm pumps are standard sizes; therefore no custom pump fee is required. ** CUSTOM PUMP VOLUME CALCULATION π x (Cylinder Radius) 2 EXAMPLE #2 FIXED RATIO CUSTOM PUMP SIZE AND 2 CYCLES REQUIRED FOR REQUIRED SHOT SIZE High volume = 2 Low volume = Mix ratio = 2/ = 2 Per part shot size = 22.5 cc (22.5 ml) Maximum output volume of 2: combination ~ 8.7 cc with a 25 mm/7.675 mm pump configuration Per part shot size divided by 2 =.25 cc (.25 ml) High volume pump = 25 mm Low volume pump = mm Volumetric mix ratio = 2/ Maximum pump combination output = 8.7 cc (.25 cc/8.7 cc) x 00% = 60% - o.k. Two (2) shots per part are needed to obtain 22.5 cc per part shot size requirement. Recommended pump configuration = 25 mm / mm 25 mm pump is standard; mm pump is special. One custom pump sizing fee applies. TO CALCULATE PUMP VOLUMES FOR CUSTOM PUMP SIZES USE THE FOLLOWING EXAMPLE (Note: All pump lengths are 2.54 cm) Volume of cylinder = (π x (Cylinder Radius) 2 x Cylinder Length) *(NOTE: Need to convert pump diameter to radius and pump size from mm to cm) *For a 6 mm diameter cylinder: Cylinder Radius = 6 mm /2 = 8 mm or 0.80 cm; Cylinder Length = 2.54 cm; π = Volume of 6 mm Pump = (3.459) x (0.80 cm) 2 x 2.54 cm = 5.07 cc 4

44 DISPENSING Variable Ratio Systems for Meter Mix 000, 2000 and 3000 Dispense Systems Variable ratio machines are capable of changing the mix ratio within the pump configurations capabilities. To specify a VARIABLE RATIO pump configuration, use chart 2. Variable ratio units have the same standard pump sizes; 8, 0, 5, 20 and 25 mm. CHART 2 - Variable Ratio Pump Diameter Configuration and Corresponding Mix Ratio Two-Part Volumetric Dispensing Meter Mix Systems HIGH VOLUME PUMP (mm) LOW VOLUME PUMP (mm) Output CCs MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN MAX MIN SELECTION PROCESS. Determine the adhesive shot volume required per part, in cubic centimeters (cc s; same as ml s), from production requirements. 2. From adhesive technical data sheet, determine the adhesive volumetric mix ratio (high volume component/low volume component). 3. Review the pump pair combination and corresponding blue maximum and minimum output and ratio range requirements within the white or gray grids and choose a configuration using the following parameters See examples 3 and 4. a. The required shot must be > 5% of the minimum output (cc s) of the combined pump pair configuration. The minimum pump configuration output is equal to the High Side Pump + minimum output for the Low Side Pump. b. The required shot should be < 85% of the of the maximum output (cc s) of the pump pair configuration. The maximum pump configuration output is equal to the (High Side pump CC maximum + maximum Low Side Pump). 4. As with fixed ratio, if required volumes are exceeded or mix ratios are not exact, repeat steps 3a or 3b in the fixed ratio selection process. EXAMPLE #3 VARIABLE RATIO EPOXY PRODUCT A High volume = 2 Low volume = Mix ratio = 2/ = 2 Per part shot size = 2.5 cc (2.5 ml) High volume pump = 5 mm Low volume pump = 3 mm 5% min pump combination output = cc (0.5 x cc cc) 85% max pump combination output = cc (4.489 cc cc) x 0.85) Mix ratio range =.88: 5.67: - pass Shot size of 2.5 cc within 5% rule Recommended configuration = 5 mm /3 mm 5 mm pump is standard; 3 mm pump is special. One special pump-sizing fee applies. EXAMPLE #4 VARIABLE RATIO EPOXY PRODUCT B High volume = 4 Low volume = Mix ratio = 4/ = 4 Per part shot size = 5.0 cc (5.0 ml) High volume pump = 5 mm Low volume pump = 3 mm 5% min pump combination output = cc (0.5 x cc cc) 85% max pump combination output = cc (4.489 cc cc) x 0.85) Mix ratio range =.88: 5.67: - pass Shot size of 2.5 cc within 5% rule Recommended configuration = 5 mm/3 mm 5 mm pump is standard; 3 mm pump is special. One special pump-sizing fee applies. 42

45 Hand Held Hot Melt Applicators Loctite Hysol hand held hot melt applicators are state-of-the -art dispensing units designed for the application of hot melt adhesives. These units combine ergonomics, userfriendly design, and reliability. Selection of a Loctite Hysol hot melt applicator should be based on the type of hot melt being used, stick diameter, and process requirements. DISPENSING Hand Held Hot Melt Applicators PRODUCT Item Number Stick Diameter Dispense Melt Rate Dispense Power Dispense Temperature Hot Melt Chemistry 2 INCH SUPERSTICK DISPENSERS NEW Loctite Hysol 050A lbs./hr. 95 C EVA/Polyolefin 2" Superstick Manual Loctite Hysol Sticks 3 lbs./hr. 95 C EVA/Polyolefin Loctite Hysol 050-HT lbs./hr. 25 C Polyamide NEW Loctite Hysol 050-GAS " Superstick Sticks 3 lbs./hr. Manual 95 C EVA/Polyolefin NEW 3 4 INCH MAXISTICK DISPENSERS Loctite Hysol 050-LITE " Superstick Sticks.5 lb./hr. Manual 204 C EVA/Polyolefin Loctite Hysol " 9 lb./hr. 82 C EVA Maxistick Manual Loctite Hysol 075-LT Sticks 5 lb./hr. 2 C CoolMelt 3 4 INCH SPRAYPAC AND POLYSHOT DISPENSERS Loctite Hysol 75-AIR " 95 C Polyshot 8 lbs./hr. Electric Loctite Hysol 75-AIR-HT Sticks 25 C Loctite Hysol 75-SPRAY " 95 C SprayPac 8 lbs./hr. Electric Loctite Hysol 75-SPRAY-HT 9804 Sticks 25 C EVA/Polyolefin Polyamide Loctite Hysol " Polyshot Sticks 6.6 lbs./hr. Manual 95 C and 25 C** EVA/Polyolefin and Polyamide URETHANE DISPENSER Loctite Hysol Reactive Urethane Cartridge Dispenser 980 N/A 3 lbs./hr. Air 2 C Reactive Urethane HOT MELT BENCH MOUNT AND CONTROLLER OPTIONS Loctite Hot Melt Bench Mount Kit Loctite Hot Melt Pneumatic Timer N/A N/A N/A N/A EVA/Polyamide ** The Loctite Hysol 75 Dispenser (manual electric) is supplied with both temperature modules. 43

46 DISPENSING Hand Held Hot Melt Applicators 2 INCH SUPERSTICK DISPENSERS LOCTITE HYSOL 050A / 050 / 050-HT Item Numbers: 96282, and Loctite industrial grade 2" stick EVA and polyolefin hot melt applicators are now available in two styles to meet your preferred grip and comfort. Loctite Hysol 050 and 050A are both lightweight and easy to use. Electrically heated, lightweight and each with their own ergonomic, easy pull triggers ensure operator comfort for long term high performance and reliability. The Loctite Hysol 050-HT model is also available for polyamide hot melts. Lightweight, well balanced, and ergonomically designed easy pull triggers for operator comfort and application control Fast heat up time for virtually immediate use Completely enclosed heater housing for maximum safety Fixed precision thermostat temperature control for consistent heating The dispense rate and timing are manually controlled with the trigger mechanism. Items and PRODUCT Loctite Hysol 050A Loctite Hysol 050 Loctite Hysol 050-HT Item Number Required Voltage 20 VAC; 60 Hz; single phase Utilities Power 250 watts 500 watts Nominal Stick Diameter 2" Superstick Size 2.0" W x 2.0" L x 6.5" H 3.25" W x 0.75" L x 7.5" H Weight.25 lbs..5 lbs. Dispense Power Manual Power Cord Length 6.0 feet (72") 6.5 feet (78") Warm-Up Time 3 to 5 minutes 4 to 5 minutes Dispense Melt Rate 4 lbs./hour 3 lbs./hour 4 lbs./hour Dispense Temperature 93 C 95 C 25 C Hot Melt Chemistry EVA and Polyolefin EVA and Polyolefin hot melts hot melts Polyamide hot melts Parts Included Additional Information () Hysol 050, 050-HT or 050A Hot Melt Applicator () Manual () Standard Nozzle () Plastic Stand () Wire Hanger For Hot Melt Nozzles and Accessories, see page 49. NEW NEW Item LOCTITE HYSOL 050-GAS Item Number: The Loctite Hysol 050- GAS Hot Melt Applicator is a hand held, cordless system. Commercially available butane gas canisters are used as the source of energy. The dispense quantity and timing are manually controlled with the ergonomic trigger mechanism. Well balanced and ergonomically designed for operator comfort and application control Low actuation force to reduce finger fatigue Regulated temperature control for consistent heating Gas powered for portability and versatility The dispense quantity and timing are manually controlled with the trigger mechanism. NEW Required Utilities (Fuel) Braun, Calibri, Ronson, Rowenta, or other high quality cigarette lighter fluids Nominal Stick Diameter 2" Superstick Size 2" W x 8" L x 7.5" H Weight 0.7 lbs. Dispense Power Manual Warm-Up Time 4 to 7 minutes Dispense Melt Rate up to 3 lbs./hour Dispense Temperature 95 C Hot Melt Chemistry EVA and Polyolefin hot melt sticks Parts Included () Hysol 050-GAS Hot Melt Applicator () Standard Nozzle () Plastic Stand () Manual Additional Information For Hot Melt Nozzles and Accessories, see page

47 LOCTITE HYSOL 050-LITE Item Number: 9628 The Loctite Hysol 050- LITE Hot Melt Applicator is a hand held, electrically heated dispenser. The dispense quantity and timing are manually controlled with the ergonomic trigger mechanism. This applicator weighs less than a pound, and is ideal for hobby, craft and light duty industrial applications. Lightweight, well balanced, and ergonomically designed for operator comfort and application control Completely enclosed heater housing for maximum safety State-of-the-art, self-regulating heater for accuracy in temperature control Electrically double insulated for additional safety The dispense rate and timing are manually controlled with the trigger mechanism. NEW Required Voltage 00/240 VAC; 50/60 Hz Utilities Power 400 W heat up, 45 W operating, 20 W rest Nominal Stick Diameter 2" Superstick Size.5" W x 8" L x 6.5" H Weight 0.8 lbs. Dispense Power Manual Power Cord Length 6.5 feet (78") Maximum Extension Cord 65 feet Warm-Up Time 5 to 7 minutes Dispense Melt Rate.5 lbs./hour Dispense Temperature 204 C Hot Melt Chemistry EVA and Polyolefin hot melt sticks Parts Included () Hysol 050-LITE Hot Melt Applicator () Standard Nozzle () Wire Stand () Manual Additional Information For Hot Melt Nozzles and Accessories, see page 49. DISPENSING Hand Held Hot Melt Applicators 3 4 INCH MAXISTICK DISPENSERS LOCTITE HYSOL 075 / 075-LT Item Numbers: and The Loctite Hysol 075 and LT (for CoolMelt ) are industrial grade, hand held, hot melt applicators. Electrically heated, both units are lightweight and easy to use. The Loctite Hysol 075 features a market leading dispense rate while both units offer extra large adhesive loading capacity. The dispense quantity and timing are manually controlled with the ergonomic trigger mechanism. Lightweight, well balanced, and ergonomically designed for operator comfort and application control Full-hand trigger for minimized operator fatigue Completely enclosed heater housing for maximum safety Fast heat up time for virtually immediate use Highest output, hand held dispenser in its class Fixed precision thermostat temperature control for consistent heating Thermal fuse protection for additional safety Multiple stick loading with a detachable top- mounted speed loader (included) The dispense rate and timing are manually controlled with the trigger mechanism. A high adhesive dispense rate, a large adhesive loading capacity and ease of application are the trademarks of this applicator. PRODUCT Loctite Hysol 075 Loctite Hysol 075-LT Item Numbers Required Voltage 20 VAC; 60 Hz; 20V; 3.3 amp single phase Utilities Power 400 watts Nominal Stick Diameter 3 4" Maxistick Size.94" W x 2.5" L x 8.25" H Weight.9 lbs. Power Cord Length 6.5 feet (78") Maximum Extension Cord 65 feet Warm-Up Time 5 minutes Dispense Power Manual Dispense Melt Rate 9 lbs./hour 9 lbs./hour Dispense Temperature 82 C 2 C Applicator Adhesive Capacity 0.2 lbs. Wire Cross-Section 6 a.w.g. minimum Hot Melt Chemistry EVA hot melt sticks Loctite Hysol CoolMelt EVA hot melt sticks Parts Included () Hysol 075 or 075-LT Applicator () Speed Loader () Plastic Dispenser Stand () Standard Nozzle (2) Stand-Off Wings () Manual Additional Information For Hot Melt Nozzles and Accessories, see page

48 DISPENSING Hand Held Hot Melt Applicators 3 4 INCH SPRAYPAC AND POLYSHOT APPLICATORS LOCTITE HYSOL 75-AIR / 75-AIR-HT PNEUMATIC APPLICATORS Item Numbers: and The Loctite Hysol 75-AIR and 75-AIR-HT (High Temperature for Polyamides) are industrial grade, electrically heated, hand held pneumatic hot melt applicators. These high capacity dispensers are rugged and designed for heavy duty work. The dispense quantity and timing are pneumatically controlled with the ergonomic trigger mechanism, greatly minimizing operator fatigue. Lightweight, well balanced, and ergonomically designed for operator comfort and application control Pneumatically powered actuation to reduce operator fatigue High melt rate for maximum output Completely enclosed heater housing for maximum safety Fixed precision thermostat temperature control for consistent heating The dispense rate is controlled by the air pressure, and the timing is controlled by the trigger mechanism. Pneumatically powered dispensing reduces operator fatigue. PRODUCT Loctite Hysol 75-AIR Loctite Hysol 75-AIR-HT Item Numbers Voltage 0/20 VAC; 50/60 Hz Required Utilities Power 500 watts Air Input 45 to 00 psi Nominal Stick Diameter 3 4" Polyshot Size 2.6" W x 2." L x 9.5" H Weight 3.89 lbs. Power Cord Length 0 feet (20") Maximum Extension Cord 65 feet Warm-Up Time 0 minutes Dispense Power Electric Dispense Melt Rate 8.8 lbs./hour Dispense Temperature 95 C 25 C Applicator Adhesive Capacity 0.25 lbs. Wire Cross-Section 6 a.w.g. minimum Hot Melt Chemistry EVA hot melt sticks Polyamide hot melts sticks Parts Included () Hysol 75-AIR or Hysol 75-AIR-HT Applicator () Plastic Stand () Valve Body Air Line Adapter () Standard Nozzle () Manual Additional Information For Hot Melt Nozzles and Accessories, see page 49. Additional Accessories Sold Separately Loctite Hot Melt Bench Mount Kit Loctite Hot Melt Pneumatic Timer Loctite Air Line Filter, Regulator, Gauge LOCTITE HYSOL 75-SPRAY / 75-SPRAY-HT PNEUMATIC APPLICATORS Item Numbers: and 9804 The Loctite Hysol 75-SPRAY and 75-SPRAY-HT (High Temperature for Polyamides) are industrial grade, electrically heated, hand held, pneumatic hot melt applicators. Fine to coarse spray pattern control is possible with a simple air rate adjustment knob. These high capacity dispensers are rugged and designed for heavy duty work. The dispense quantity and timing are pneumatically controlled with the ergonomic trigger mechanism, greatly minimizing operator fatigue. Adjustable flow control for tailoring the spray pattern Patented spray technology for small or large spray pattern Automatic end-of-cycle purge to prevent nozzle clogging Lightweight, well balanced, and ergonomically designed for operator comfort and application control Pneumatically powered actuation to reduce operator fatigue High melt rate for maximum output Completely enclosed heater housing for maximum safety Fixed precision thermostat temperature control for consistent heating By using the air flow control, the spray pattern can be varied from a narrow to a wide spiral pattern. The dispense rate is controlled by the air pressure, and the timing is controlled with the trigger mechanism. Pneumatically powered dispensing reduces operator fatigue. PRODUCT Hysol 75-SPRAY Hysol 75-SPRAY-HT Item Numbers Voltage 0/20 VA; 50/60 Hz Required Utilities Power 500 watts Air Input 45 to 00 psi Spray Pattern Ultra-wide spray nozzle:.5" minimum / 6" maximum Standard medium spray nozzle:.25" minimum / 5" maximum Narrow spray nozzle: 0.5" minimum /.25" maximum Nominal Stick Diameter 3 4" SprayPac Sticks Size 2.6" W x 2." L x 9.5" H Weight 4 lbs. Power Cord Length 0 feet (20") Maximum Extension Cord 65 feet Warm-Up Time 0 minutes Dispense Power Electric Dispense Melt Rate 8 lbs./hour Dispense Temperature 95 C 25 C Applicator Adhesive Capacity 0.25 lbs. Wire Cross-Section 6 a.w.g. minimum Hot Melt Chemistry EVA Spray hot melt sticks Polyamide Spray hot melt sticks Parts Included () Hysol 75-SPRAY or Hysol 75-SPRAY-HT Applicator () Plastic Stand () Valve Body Air Line Adapter () Manual () Standard Wide Spray Nozzle Additional Information For Hot Melt Nozzles and Accessories, see page 49. Additional Accessories Sold Separately Loctite Air Line Filter, Regulator, Gauge 46

49 LOCTITE Heading HYSOL 75 MANUAL APPLICATOR Epoxy & Urethane Adhesives Item Number: The Loctite Hysol 75 is an industrial grade, electrically heated, hand held, manual hot melt applicator. This unit comes with two plug-in thermostats for either EVA or polyamide adhesives. The dispense quantity and timing are manually controlled with the ergonomic trigger mechanism. The complete source on Loctite brand adhesives, Includes two plug-in modules for dispensing both sealants, polyamide lubricants, and EVA coatings, hot melts dispensing and curing equipment Lightweight, available well balanced, only from and ergonomically Henkel Corporation. designed for operator comfort and application control Completely enclosed heater housing for maximum safety Fast heat up time for virtually immediate use Advanced electronic controller provides power saving mode, when not in use for long periods of time Fixed precision thermostat (plug- in module) for consistent heating Thermal fuse protection for additional safety The dispense rate and timing are manually controlled with the trigger mechanism. Required Voltage 0/20 VAC; 50/60 Hz Utilities Power 400 watts Nominal Stick Diameter.75" Polyshot Sticks Size 2.67" W x 2.25" L x 9.63" H Weight 2.65 lbs. Power Cord Length 0 feet (20") Maximum Extension Cord 65 feet Warm-Up Time 5 to 7 minutes Dispense Power Manual Dispense Melt Rate 6.6 lbs./hour Dispense Temperature 95 C or 25 C Applicator Adhesive Capacity 0.25 lbs. Wire Cross-Section 6 a.w.g. minimum Hot Melt Chemistry EVA and polyamide hot melt sticks Parts Included () Hysol 75 Applicator () Plug-In Module (25 C) () Plastic Stand () Standard Nozzle () Plug-In Module (95 C) () Manual Additional Information For Hot Melt Nozzles and Accessories, see page 49. DISPENSING Hand Held Hot Melt Applicators URETHANE DISPENSER LOCTITE HYSOL REACTIVE URETHANE CARTRIDGE DISPENSER Item Number: 980 The Loctite Hysol Reactive Urethane Cartridge Dispenser is used to dispense reactive polyurethane hot melts from 300 ml cartridges. This electrically heated, pneumatic dispenser includes a pressure-regulating stand with optional vertical application stand and foot switch for hands- free application. To minimize cartridge change- over times, the Loctite Cartridge Pre- Heater (item 9802) is recommended. Required Utilities Voltage Power 20 VAC; 60 Hz; single phase 400 watts Lightweight, well balanced, and ergonomically designed for operator comfort and application control Low actuation force to reduce finger fatigue Electronic temperature control Rugged molded thermoset plastic housing for cool to the touch operation up to 250 F Fixed precision temperature: 250 F (2 C) Single cartridge loading Direct nozzle cartridge mounting for quick cartridge changeover Various nozzles for different dispense patterns This unit is used in the manual mode, where the operator manually begins and terminates the pneumatic dispense cycle by a hand trigger. Flow control is achieved by adjusting the regulator supplied on the base of the unit. Air Input 80 psi air, filtered to 40 micron Size 3." W x 2.5" L x 0.3" H Weight 3 lbs. Adhesive Dispenses 300 cc aluminum cartridge Air Output Maximum 90 psi Warm-Up Time 7 to 0 minutes Dispense Power Air Dispense Melt Rate 3.5 lbs./hour Dispense Temperature 2 C Applicator Adhesive Capacity 0.25 lbs. Hot Melt Chemistry Loctite Hysol Reactive Urethane hot melts Parts Included () Hysol Reactive Urethane Cartridge Dispenser () Base with Regulator and Gauge () Wire Stand () 300 cc Cartridge Adapter () Nozzle with Cap () Heat Resistant Gloves () Cartridge Piercer () Tubing Assembly () Manual Additional Information For Hot Melt Nozzles and Accessories, see page 49. Additional Accessories Sold Separately 9802 Loctite Cartridge Pre-Heater 47

50 Hand Held Hot Melt Applicators DISPENSING HOT MELT BENCH MOUNT AND CONTROLLER OPTIONS LOCTITE HOT MELT BENCH MOUNT KIT Item Number: LOCTITE HOT MELT PNEUMATIC TIMER Item Number: The Loctite Hot Melt Bench Mount Kit is used for converting the Loctite Hysol 75-AIR or 75-AIR-HT applicator into a hands-free, bench- top dispenser. The Loctite Hot Melt Pneumatic Timer is used in conjunction with the Loctite Hot Melt Bench Mount Kit and Loctite Hysol 75-AIR and 75-AIR-HT applicator for controlled dot dispensing. These units are used for any hot melt application where holding an applicator is not desirable. This is especially relevant to applications where the part itself must be moved. Typical applications include: cardboard boxes and related packaging materials, wood and plastic panels, furniture components, etc. Loctite Hot Melt Bench Mount Kit Ready-made bench-top stand easily attaches to the Loctite Hysol 75-AIR or 75-AIR-HT applicator, and includes a pneumatic actuator and foot switch Included right angle adapter accepts any Loctite brand hot melt nozzle Loctite Hot Melt Pneumatic Timer Directly accepts the Loctite Hot Melt Bench Mount Kit Programmable timer from 0 to second for controlled dot dispensing Internal pneumatic timing device requires no electrical connection Includes a manual mode for set-up and purging By simply pushing the included foot switch, an operator can dispense beads or dots of hot melt adhesives onto a part without the hindrance of holding the applicator. By using the preset timer, each push of the foot switch will dispense a single controlled dot of adhesive Loctite Hot Melt Bench Mount Kit. PRODUCT Loctite Hot Melt Bench Mount Kit Loctite Hot Melt Pneumatic Timer. Loctite Hot Melt Pneumatic Timer Item Number * Required Utilities Air Input: 60 to 00 psi Size 7.8" W x.9" Depth x 6.4" H 7.4" W x 7.8" L x 2.75" H Weight 5.4 lbs. 2.6 lbs. Hot Melt Chemistry EVA/Polyamide Parts Included () Stand with Pneumatic Actuator () Right Angle Adapter for Nozzle () Foot Switch () Manual () Pneumatic Timer () Manual Additional Information For Hot Melt Nozzles and Accessories, see page 49. * Note: Applicators are sold separately. 48

51 Loctite Brand Hot Melt Nozzles and Accessories PRODUCT Item Number (Single pack) 495 (Single pack) (5 pack) ANZ023N (5 pack) (5 pack) Description Adapter/Check Valves for Nozzles Standard Nozzle Adapter with Check Valve and Jam Nut -Hole Nozzle 0.08" Diameter Cone Tip (5 pack) -Hole Nozzle 0.09" Diameter Cone Tip 2-Hole Nozzle 0.06" diameter x 0.39" spacing 3-Hole Nozzle 0.06" diameter x 0.20" spacing Diagonal Extension Nozzle Tip = 0.4" diameter x.23" long Needle Extension Nozzle Tip = 0.05" diameter x.32" long Spreader Extension Nozzle Tip = (0.09" x 0.25") sq. x.32" long Used With 98544, , 9803, 98032, 98035, 98036, , , , 9803, 98032, 98033, 98034, 98035, 98036, , 9803, 98032, 98033, 98034, 98035, 98036, 98040, 98544, , 9803, 98032, 98033, 98034, 98035, 98036, 98040, 98544, , 9803, 98032, 98033, 98034, 98035, 98036, 98040, 98544, , 9803, 98032, 98033, 98034, 98035, 98036, 98040, 98544, , 9803, 98032, 98033, 98034, 98035, 98036, 98040, 98544, PRODUCT Item Number Description Cartridge Pre-Heater Holds (2) 300 ml cartridges Standard Adapter for 300 ml Cartridges Standard -Hole Nozzle 0.098" diameter cone tip, with integral check valve (Includes protective cap) Adapter/Check Valve for Specialty Nozzles Needle Jet Nozzle Tip = 0.05" diameter x.26" long (Requires adapter) Diagonal Extension Nozzle Tip = 0.23" diameter x.276" long (Requires adapter) Flat Spreader Nozzle Tip = (0.084" x.77") sq. x.237 long (Requires adapter) Used With DISPENSING Hand Held Hot Melt Applicators L-Nozzle 0.06" diameter x 0.85" offset T-Nozzle 0.06" diameter x.5" spacing Standard Medium Spray Nozzle.25" to 5" diameter pattern 98033, 98034, 98035, 98036, 98040, 98544, , 98034, 98035, 98036, 98040, 98544, , Hole Nozzle 0.06" diameter x 0.39" spacing (Requires adapter) 3-Hole Nozzle 0.06" diameter x 0.20" spacing (Requires adapter) Narrow Spray Nozzle 0.05" to.25" diameter pattern Ultra Wide Spray Nozzle.5" to 6.0" diameter pattern 98037, , Injection Needle Nozzle with Integral Check Valve Tip = 0.059" diameter x 0.97" long Standard -Hole Nozzle with Integral Check Valve Tip = 0.0" diameter x 0.6" long Spreader Nozzle with Integral Check Valve Tip = (0.08" x 0.25") sq. x 0.47" long Pencil Point Nozzle with Integral Check Valve Tip = 0.08" diameter x 0.24" long 98029, , , Heavy Duty Metal Stand for Bench Top or Wall Mounting Tool Hanger/Balancer 0 to.5 kg 98030, 9803, 98032, 98035, 98036, 98037, 98040, 9804 All Hot Melt Applicators Precision Nozzle with Integral Check Valve Tip = 0.05" diameter x 0.20" long Extension Nozzle with Integral Check Valve Tip = 0.0" diameter x 0.50" long 98029, , Air Line Filter, Regulator Gauge 0 to 50 psi All Pneumatic Applicators Silicone Rubber Safety Cap (2 pack) (for use with , , , 9628 For custom hot melt dispense nozzles, contact the Special Equipment Group of Henkel at -800-LOCTITE ( ). 49

52 DISPENSING Bulk Hot Melt Systems Bulk Hot Melt Systems Henkel s Loctite Hysol bulk hot melt systems offer high performance control and reliability for all of your hot melt dispensing needs. You can rely on Henkel to supply you with performance hot melt adhesives as well as an array of standard high volume hot melt dispensing equipment. Henkel offers true one stop shopping for your complete adhesive solution. These systems are rugged, compact and feature internal system diagnostics which monitor the temperatures and system settings. Loctite Hysol bulk hot melt systems accommodate all sizes of Loctite Hysol EVA, polyamide and polyolefin hot melt adhesives and share these performance features: PTFE coated reservoir reduces tank residue High surface area melt grid is integrated with tank walls to ensure fast and even heating, eliminating hot spots within the tank All systems are CE certified All system settings and system diagnostics are visible on front display for at a glance system status Gear pump for the most consistent product delivery pressure Bulk Systems PRODUCT Loctite Hysol PUR Hot Melt Dispenser Item Number Maximum Length of Hoses Voltage Amps Maximum Number of Hoses Maximum Dispense Rate feet 230 VAC 95 lbs./hr. Maximum Dispense Temperature 425 F (28 C) Maximum Tank Setting Temperature 395 F (202 C) Used to Dispense Reactive Polyurethane Hot Melts from 5 gallon pails Loctite Hysol Bulk-2 System feet 5 VAC 5 2 lbs./hr. 40 F (28 C) 395 F (202 C) EVA, Polyamide, Polyolefin feet 230 VAC 3 Loctite Hysol Bulk-4 System feet 5 VAC feet 230 VAC lbs./hr. 425 F (28 C) 395 F (202 C) EVA, Polyamide, Polyolefin Loctite Hysol Bulk-34 System feet 230 VAC lbs./hr. 425 F (28 C) 395 F (202 C) EVA, Polyamide, Polyolefin 50

53 DISPENSING Bulk Hot Melt Systems LOCTITE HYSOL PUR HOT MELT DISPENSER Item Number: The Loctite Hysol PUR Hot Melt dispenser is designed to effectively pump and apply reactive polyurethane hot melt adhesives directly from 5 gallon pails. This dispenser utilizes an innovative inflatable silicone seal design to insure moisture is kept separated from the reactive PUR Hot Melt. Product is dispensed using a rugged gear pump design, and with 3 separate heating zones (platen, hose, and applicator) to insure long term reliable dispensing. Fully enclosed pail unloading station with a rugged silicone seal designed to keep moisture out, and an elevator platform to ensure continuous seal/hot melt contact as the pail is emptied 3 zone heating with convenient digital control panel with component on/off LED displays and digital temperature read- outs Inflatable silicone pail seal design ensures reactive moisture is kept out of a 5 gallon pail during operation 3 zone heating controls, pail platen, hose, and applicator with no check valves to repair or replace Can be used on any standard hot melt adhesive in a 5 gallon pail Utilities A 5 gallon pail of PUR Hot Melt is positioned onto the elevator platform and raised to engage an inflatable silicone seal into the pail. The platen is heated to the desired temperature and melts the product which then flows towards the center of the platen. As the elevator maintains pressure on the pail, the liquefied product is channeled towards the gear pump around the bottom center of the platen. Utilizing the control panel, a temperature range is selected that is within the product s use temperature. Once the application temperature is reached, the equipment is ready to dispense product. When the applicator trigger is actuated, the gear pump turns on and forces the product down the heated hose and towards the dispense applicator. Gear pump speed can also be controlled to change the application rate. Dimensions Weight Dispense Rate Used to Dispense Packages Types Electric: 230 VAC; Single Phase, 30 amp maximum Pneumatic: 65 to 90 psi 52.5" H x 30" W x 22" D 375 lbs. Up to 95 lbs./hour Reactive Polyurethane Hot Melts 5 gallon pails Parts Included () Loctite PUR Hot Melt 5 Gallon Pail Pump Complete System () 8' Heated Hose Additional Information See pages to select from the wide assortment of applicators, hoses, nozzles, timers, controllers and accessories to complete your PUR hot melt dispense system. 46 5

54 Bulk Hot Melt Systems DISPENSING LOCTITE HYSOL BULK-2 SYSTEM Item Numbers: 983 and 9832 The Loctite Hysol Bulk-2 Hot Melt System is a compact and efficient bulk hot melt unit capable of manual or automatic product delivered up to 2 lbs./hr. The unit includes analog controls with simple modular connections for hoses, controllers and timers that are sold separately. These CE certified units have three independent temperature controls for the tank, hosing and dispense valves that will provide an effective extrusion or spray application for a wide range of hot melt adhesives. Adjustable pressure, all electric AC gear pump Three controllable temperature zones over six fine tuned ranges up to 40 F (20 C) PTFE coated reservoir with high surface area melt grid Internal system diagnostics automatically troubleshoot electrical connections and eliminate overheating Simple analog controls with high visibility LED indicator lamps for temperature range and diagnostic status Simple modular connections for hoses, controllers, timers and other optional interfaces CE Certified Compact footprint This unit is designed to melt and dispense hot melt adhesive when outfitted with optional hand held or mountable applicators, for either spray or extrusion applications. Appropriate dispense controllers, timers, hosing and nozzle accessories are also selected based on process needs to complete the system. Item Number Voltage 5 VAC 230 VAC Standard Tank Capacity 2 lbs. (5.4 kg) Used to Dispense All forms of Loctite Hysol EVA, Polyamide, Polyolefin Maximum Dispense Rate 2 lbs./hr. (5.4 kg/hr.) Maximum Temperature Tank Setting 395 F (202 C) Maximum Dispense Temperature 40 F (20 C) Temperature Control Zones 3 Controls Analog Maximum Number of Hoses Maximum Total Length of Hoses 6 feet 24 feet Available Dispense Patterns Extrude, Swirl Spray, Fan Spray, Cone Spray Pump Pressure 0 to 300 psi Dimensions (Lid Open) 5.9" L x 0.5" W x 20.0" H Weight (Empty) 4 lbs. (8.6 kg) System Power Consumption 700 watts 2780 watts Melt Tank Power Consumption 900 watts 700 watts Parts Included () Hysol Bulk-2 Hot Melt System () Temperature Range Adjustment Tool () 0 mm Hex Key for flow by-pass adjustment () Manual Additional Information See pages to select from the wide assortment of applicators, hoses, nozzles, timers, controllers and accessories to complete your bulk hot melt dispense system. 52

55 DISPENSING Bulk Hot Melt Systems LOCTITE HYSOL BULK-4 SYSTEM Item Numbers: 9833 and 9834 The Loctite Hysol Bulk-4 Hot Melt System is a compact and efficient bulk hot melt unit capable of manual or automatic product delivered up to 28 lbs./hr. The unit includes all digital controls and displays with simple modular connections for hoses, controllers and timers that are sold separately. These CE certified units have three independent temperature controls for the tank, hosing and dispense valves that will provide an effective extrusion or spray application for a wide range of hot melt adhesives. Two-channel controls on front panel with full digital display of set points, temperature ranges, and all diagnostic functions Highly reliable variable speed DC gear pump with integrated flow control offers consistent product delivery and extended service life Capable of two, independent and fully customizable dispense lines Up to five controllable temperature zones over six individual ranges for fine tuned temperature control User selectable standby mode automatically protects against overheating product. This extends product life, lowers energy consumption, and still allows for rapid restart of the unit PTFE coated reservoir with high surface area melt grid CE Certified Compact footprint This unit is designed to melt and dispense hot melt adhesive when outfitted with optional hand held or mountable applicators, for either spray or extrusion applications. Appropriate dispense controllers, timers, hosing and nozzle accessories are also selected based on process needs to complete the system. Item Number Voltage 5 VAC 230 VAC Standard Tank Capacity 4 lbs. (6.4 kg) Optional Tank Feed Hopper 70 lbs. (3.75 kg) Used to Dispense All forms of Loctite Hysol EVA, Polyamide, Polyolefin Maximum Dispense Rate 28 lbs./hr. (2.7 kg/hr.) Maximum Temperature Tank Setting 395 F (202 C) Maximum Dispense Temperature 425 F (28 C) Temperature Control Zones 5 Controls Digital Maximum Number of Hoses 2 Maximum Total Length of Hoses 20 feet 48 feet Available Dispense Patterns Extrude, Swirl Spray, Fan Spray, Cone Spray Pump Pressure 0 to 300 psi Dimensions (Lid Open) 20.2" L x.5" W x 22.5" H Weight (Empty) 5 lbs. (23.2 kg) System Power Consumption 2220 watts 3860 watts Melt Tank Power Consumption 900 watts 700 watts Parts Included () Hysol Bulk-4 Hot Melt System () Temperature Range Adjustment Tool () 0 mm Hex Key for flow by-pass adjustment () Manual Additional Information See pages to select from the wide assortment of applicators, hoses, nozzles, timers, controllers and accessories to complete your bulk hot melt dispense system. 53

56 Bulk Hot Melt Systems DISPENSING LOCTITE HYSOL BULK-34 SYSTEM Item Number: 9835 The Loctite Hysol Bulk-34 Hot Melt System is a compact and efficient bulk hot melt unit capable of manual or automatic product delivered up to 75 lbs./hr. The unit includes all digital controls and displays with simple modular connections for hoses, controllers and timers that are sold separately. These CE certified units have three independent temperature controls for the tank, hosing and dispense valves that will provide an effective extrusion or spray application for a wide range of hot melt adhesives. Two-channel controls on front panel with full digital display of set points, temperature ranges and all diagnostic functions Highly reliable variable speed DC gear pump with integrated flow control offers consistent product delivery and extended service life Capable of up to four, independent and fully customizable dispense lines Up to nine controllable temperature zones over six individual ranges for fine tuned temperature control User selectable standby mode automatically protects against overheating product. This extends product life, lowers energy consumption, and still allows for rapid restart of the unit PTFE coated reservoir with high surface area melt grid CE Certified Compact footprint This unit is designed to melt and dispense hot melt adhesive when outfitted with optional hand held or mountable applicators, for either spray or extrusion applications. Appropriate dispense controllers, timers, hosing and nozzle accessories are also selected based on process needs to complete the system. Voltage 230 VAC Standard Tank Capacity 34 lbs. (5.4 kg) Optional Tank Feed Hopper 00 lbs. (45.4 kg) Used to Dispense All forms of Loctite Hysol EVA, Polyamide, Polyolefin Maximum Dispense Rate 75 lbs./hr (34. kg/hr.) Maximum Temperature Tank Setting 395 F (202 C) Maximum Dispense Temperature 425 F (28 C) Temperature Control Zones 9 Controls Digital Maximum Number of Hoses 4 Maximum Total Length of Hoses 72 feet Available Dispense Patterns Extrude, Swirl Spray, Fan Spray, Cone Spray Pump Pressure 0 to 300 psi Dimensions (Lid Open) 22.0" L x 4.5" W x 27.0" H Weight (Empty) 86 lbs. (39.0 kg) System Power Consumption 6600 watts Melt Tank Power Consumption 3400 watts Parts Included () Hysol Bulk-34 Hot Melt System () Temperature Range Adjustment Tool () 0 mm Hex Key for flow by-pass adjustment () Manual Additional Information See pages to select from the wide assortment of applicators, hoses, nozzles, timers, controllers and accessories to complete your bulk hot melt dispense system. 54

57 Loctite Hysol Bulk Hot Melt System Applicators In any adhesive application, the accuracy of your dispense equipment can define the level of success of the process. Henkel offers four accurate and convenient styles of dispense applicators to suit any process requirement. Whichever dispense applicator you choose, it must match the voltage of the melt unit. The 2 hand and mounted styles also come in multiple coil voltages (24 VDC, 5 VAC, and 230 VAC) to match external control systems if employed. ) Loctite Hysol Hand Held Applicator Convenient, durable, fully insulated, and customizable Available in top or bottom inlet applicators 2) Loctite Hysol Mounted Applicator (for automatic or fixed position dispense) Excellent design for automated applications Select electrically controlled mounted applicators for dispensing products up to 5,000 cp Select pneumatically controlled mounted applicators for high cycle rates up to 2,400 cpm Compact design is easily mounted to a robot or incorporated into a workcell or fixture 3) Loctite Hysol 2 Hand Applicator Electrically controlled for precision dispense Vertical design allows direct positioning over the part DISPENSING Bulk Hot Melt Systems PRODUCT Item Number Compatible with these Melt Units Melt Unit Voltage Control Coil Voltage/Item # Loctite Hysol Hand Held Bottom Inlet Applicator , VAC N/A , 9834, VAC N/A Loctite Hysol Hand Held Top Inlet Applicator , VAC N/A , 9834, VAC N/A , VAC 24 VDC** Loctite Hysol Mounted Applicator (Electric Open/Close) , VAC 5 VAC , 9834, VAC 24 VDC** , 9834, VAC 5 VAC , 9834, VAC 230 VAC 24 VDC **/ , VAC 5 VAC/ Loctite Hysol Mounted Applicator (Pneumatic Open/Close) 230 VAC/ VDC **/ , 9834, VAC 5 VAC/ VAC/ , VAC 24 VDC ** Loctite Hysol 2 Hand Applicator* , VAC 5 VAC , 9834, VAC 24 VDC** , 9834, VAC 5 VAC , 9834, VAC 230 VAC *All of the Loctite Hysol 2 Hand Applicators require a separate applicator control cord and either an extrude or spray control module. Select between single switch (only requires one hand to actuate) or two switch (requires two hands to actuate) to control the unit Hand Applicator Cord, Switch Hand Applicator Cord, 2 Switch ** Choose 24 VDC for use with Event Timers. Solenoid Valve is required and sold separately. 55

58 DISPENSING Loctite Brand Extrusion Hoses Choose between 5 and 230 VAC to match your melt unit, then select the required length of hose. 4 feet 6 feet 8 feet 0 feet 2 feet 6 feet 8 feet 24 feet Voltage / /2 5 VAC Bulk Hot Melt Systems VAC Not available for Loctite Hysol Bulk-2 5 VAC System (983). 2 Not available for Loctite Hysol Bulk-4, 5 VAC when using dual hoses. Loctite Brand Extrusion Controllers For 2 Hand Applicator only. This unit allows the integration of the melt tank pump function and 2 Hand Applicator activation in a single control unit. Choose from 5 and 230 VAC to match your melt unit. Item Number Voltage VAC VAC Loctite Brand Spray Hoses Choose between 5 and 230 VAC to match your melt unit, then select the required length of hose. 4 feet 6 feet 8 feet 0 feet 2 feet 6 feet 8 feet 24 feet Voltage / /2 5 VAC VAC Not available for Loctite Hysol Bulk-2 5 VAC System (983). 2 Not available for Bulk-4, 5 VAC when using dual hoses. Loctite Brand Spray Controllers Loctite Hysol Spray Controllers utilize the latest in microprocessor technology to handle a multitude of adhesive patterns. A controller and appropriate nozzle are required for spray or swirl dispensing. See page 57 for a complete line of bulk hot melt system nozzles and accessories to meet all your dispensing requirements. Loctite Hysol Spray Controller Item Number Voltage VAC Timers Loctite Hysol Timers provide timed dispense control for all Loctite Hysol automatic bulk hot melt systems. Timers can be used in either 5 or 230 VAC systems. The Loctite Hysol Two and Four Event Timers contain independently selectable output channels that control 24 VDC or AC line voltage applicators. They feature separate high and low speed ranges to control delay and length of pattern. The Four Event Timer has an added stitch mode pattern application. These modular units can be used with foot switch, proximity or optical sensors. Loctite Hysol Two Event Timer Loctite Hysol Four Event Timer VAC Loctite Hysol 2 Hand Applicator Spray Controller Item Number Voltage VAC VAC If used with Bulk-34 System additional cable, Item Number is also required and sold separately. Loctite Brand Timer and External Interface Cords PRODUCT Loctite Hysol Bulk-2 System Loctite Hysol Bulk-4 System Loctite Hysol Bulk-34 System Two or With 24 VDC Output Four Event Timer With Line Voltage Output External PLC Interface Cords If multiple applicators are required, use either line voltage applicators or pneumatic applicators only. 2 Can not be used with multiple 24 VDC electric valves (Items 9843, 9844, 9845 or 9846). 56

59 Loctite Brand Bulk Hot Melt System Nozzles and Accessories Heading Epoxy & Urethane Adhesives PRODUCT Item Number Description PRODUCT Item Number Description Bulk-4 Hopper Upgrade to 40 lb. Capacity Proximity Sensor Assembly Optical Sensor Assembly Bulk-34 Hopper Upgrade to 78 lb. Capacity Sensor Cord Extension, 0 Feet Bulk Units Floor Stand 9860 Foot Switch Assembly Bulk-2 Applicator Hanger Arm Kit Valve Mount Bracket Kit Bulk-4 and 34 Applicator Hanger Arm Kit Feed Line Adapter, 45 Degrees Hose Cradle Tension Balancer Feed Line Adapter, 90 Degrees Hose Cradle and Tension Balancer DISPENSING Bulk Hot Melt Systems PRODUCT Item Number Description Extrusion Nozzle 2" 0.020" Diameter Extrusion Nozzle 2" 0.030" Diameter Extrusion Nozzle 2" 0.040" Diameter Extrusion Nozzle 2" 0.050" Diameter Extrusion Nozzle 2" 0.060" Diameter Extrusion Nozzle 2" 0.070" Diameter Extrusion Nozzle 2" 0.080" Diameter Extrusion Nozzle 2" 0.090" Diameter Extrusion Nozzle " 0.020" Diameter Extrusion Nozzle " 0.030" Diameter Extrusion Nozzle " 0.040" Diameter Extrusion Nozzle " 0.050" Diameter Extrusion Nozzle " 0.060" Diameter Extrusion Nozzle " 0.070" Diameter Extrusion Nozzle " 0.080" Diameter Extrusion Nozzle " 0.090" Diameter Extrusion Nozzle 2" 0.020" Diameter Extrusion Nozzle 2" 0.030" Diameter Extrusion Nozzle 2" 0.040" Diameter Extrusion Nozzle 2" 0.050" Diameter Extrusion Nozzle 2" 0.060" Diameter Extrusion Nozzle 2" 0.070" Diameter Extrusion Nozzle 2" 0.080" Diameter Extrusion Nozzle 2" 0.090" Diameter Extrusion Nozzle 3" 0.020" Diameter Extrusion Nozzle 3" 0.030" Diameter Extrusion Nozzle 3" 0.040" Diameter Extrusion Nozzle 3" 0.050" Diameter Extrusion Nozzle 3" 0.060" Diameter Extrusion Nozzle 3" 0.070" Diameter Extrusion Nozzle 3" 0.080" Diameter Extrusion Nozzle 3" 0.090" Diameter Extrusion Button Nozzle 0.02" Diameter Extrusion Button Nozzle 0.05" Diameter Extrusion Button Nozzle 0.025" Diameter Extrusion Button Nozzle 0.030" Diameter Extrusion Button Nozzle 0.040" Diameter Extrusion Button Nozzle 0.050" Diameter Extrusion Button Nozzle 0.060" Diameter Extrusion Button Nozzle 0.070" Diameter Extrusion Button Nozzle 0.080" Diameter Extrusion Button Nozzle 0.090" Diameter PRODUCT Item Number Description Swirl Nozzle Assembly without Nozzle Swirl Nozzle 0.030" Diameter Swirl Nozzle 0.045" Diameter Swirl Nozzle 0.060" Diameter Swirl Nozzle 0.080" Diameter Spray Nozzle Assembly with Fan Air Cap without nozzle Spray Nozzle Assembly with Cone Air Cap without Nozzle Spray Nozzle and O-ring 0.020" Diameter Spray Nozzle and O-ring 0.030" Diameter Spray Nozzle and O-ring 0.040" Diameter Spray Nozzle and O-ring 0.050" Diameter T-Bar Nozzle 2" x " T-Bar Nozzle 2" x 2" T-Bar Nozzle 2" x 3" Y-Bar Nozzle 2" x " Y-Bar Nozzle 2" x 2" Y-Bar Nozzle 2" x 3" Direction Nozzle 0.00" Diameter (2 pack) Direction Nozzle 0.020" Diameter (2 pack) Direction Nozzle 0.030" Diameter (2 pack) Direction Nozzle 0.040" Diameter (2 pack) Direction Nozzle Assembly 0.00" Diameter (2 pack) Direction Nozzle Assembly 0.020" Diameter (2 pack) Direction Nozzle Assembly 0.030" Diameter (2 pack) Direction Nozzle Assembly 0.040" Diameter (2 pack) Direction Nozzle Screw (5 pack) Direction Nozzle O-Ring (0 pack) Blank Screw Assembly (5 pack) 57

60 DISPENSING Hand Held Valves Hand Held Valves Loctite brand hand held dispensing valves are used where ergonomic design for hand dispensing of fluids is desired. Designed for use with Loctite brand controllers and reservoirs, these hand held valves utilize passive wetted components for universal compatibility with many fluids. Selection of a Loctite brand hand held valve is based on the desired dispensing controls, the dispense principal of the delivery system, and other process requirements. PRODUCT Item Number Type Viscosity Range Dispense Patterns Used to Dispense Stroke Adjustment Actuation LOW VISCOSITY CYANOACRYLATE APPLICATOR Loctite LV Hand Held Applicator 9730 Pneumatic Low Drop, Dot, Bead Instant Adhesives, Retaining Compounds, Threadlockers Yes Foot GENERAL PURPOSE APPLICATORS Loctite Manual Hand Held Applicator 97 Manual Low to Medium Drop, Dot, Bead Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers Yes Finger Loctite Pneumatic Hand Held Applicator 972 Pneumatic Low to Medium Drop, Dot, Bead Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers Yes Foot Loctite Pneumatic Hand Held Applicator 976 Pneumatic Low to Medium Drop, Dot, Bead Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers Yes Finger PINCH TUBE APPLICATORS Loctite Vari-Drop Applicator Pinch Tube Low to Medium Drop, Dot, Bead Instant Adhesives, Retaining Compounds, Threadlockers Yes Finger 58

61 Dispenser, Controller and Reservoir are required with these valves. DISPENSING Hand Held Valves LOW VISCOSITY CYANOACRYLATE APPLICATOR LOCTITE LV HAND HELD APPLICATOR Item Number: 9730 The Loctite LV Hand Held Applicator is a pneumatically operated, adjustable seat valve designed for accurate dispensing of low viscosity adhesives including cyanoacrylates. The valve body and stem are constructed of PTFE to prevent premature curing and together with the fine tuning stroke adjustment, this valve can deliver very small and repeatable drop sizes shot after shot. This valve must be used in conjunction with a Loctite brand controller and product Type reservoir, sold separately. Viscosity Range Dispenses low viscosity cyanoacrylates, anaerobic, and other adhesives under 0,000 cp Slim, ergonomic design greatly reduces hand fatigue Forward closing to avoid air entrapment and potential premature curing of cyanoacrylates Stroke adjustment for fine -tuning of dispense characteristics Dispenses repeatable drop sizes down to g Easy repair/replacement of wetted components When used in conjunction with a pressure-time controller and adhesive reservoir, the valve is opened by an internal, single - acting cylinder and piston rod. After initiating the control cycle, the piston is pulled, opening the PTFE flow channel, and allowing adhesive to pass. At the end of the controlled open time, pressure is released and the valve is closed via an internal spring mechanism, closing off the flow channel. The amount of dispensed adhesive is controlled by adjustment of air pressure, valve open time, size of dispensing needle, and piston stroke. NO FLOW FLOW The RED represents the fluid path. Pneumatic Low Size 7" L x.6" Maximum Diameter (70 mm L x 40 mm Maximum Diameter) Weight 5 oz. (40 g) Maximum Cycle 2 Shots per second Port Size Fluid Inlet 4" Tubing Air Inlet 5 32" Tubing Fluid Pressure 4 to 30 psi (0.25 to 2 bar) Pneumatic Supply Minimum: 60 psi (4.8 bar) / Maximum: 00 psi (7 bar) Dispense Patterns Drop, Dot, Bead Used to Dispense Instant Adhesives, Retaining Compounds, Threadlockers Stroke Adjustment Yes Actuation Foot Parts Included () 2 m Product Feed Line, PTFE lined, 4" OD () LV Hand Held Applicator () 2 m Pneumatic Tubing () Needle Variety Kit () Silicone Grease () Manual Additional Information Loctite Shot Miser Reservoir / 9700 Loctite Integrated Semi-Automatic Controllers Loctite Digital Multi-Functional Controller For Spare Parts and Accessories, see page 84. For Fluid Compatibility Selector Chart, see page 63. For Dispense Tips, see pages Additional Accessories Sold Separately Loctite Shot Miser Controller 9707 / Loctite Integrated Semi-Automatic Controllers with Low Level Sensor 970 Loctite Digital Dispense Controller Loctite Finger Switch for Loctite Single Channel Automatic Controller / / / / / Loctite Bond-A- Matic Reservoirs 9850 Loctite Applicator Holder 59

62 Hand Held Valves DISPENSING GENERAL PURPOSE APPLICATORS LOCTITE MANUAL HAND HELD APPLICATOR Item Number: 97 The Loctite Manual Hand Held Applicator is a consistent performing, highly reliable, adhesive dispense valve. It features a manual trigger actuator that is ergonomically designed for comfort, application control, and a low actuation force to reduce hand fatigue. It also incorporates a suck-back feature that prevents dripping or stringing. This valve must be used in conjunction with a Loctite Bond-A-Matic 3000 Reservoir (item for low viscosity, item for medium to high viscosity), sold separately. Since this valve is manually controlled, it is not capable of timed dispensing or compatible with low level sensing. Pistol grip provides comfort and control Low actuation force to reduce hand fatigue Suck- back feature ensures accuracy and control Dispenses products up to 5,000 cp with 4" feed line (standard) Dispenses products up to 80,000 cp with 3 8" feed line (optional) Operational with manually controlled pressure reservoirs The hand held applicator is a modular design made up of a product shut- off valve and valve actuator. This type of design provides quick on- line serviceability. The adjustable suck- back feature eliminates stringing and dripping. The shut- off of the Loctite Hand Held Applicator takes place mechanically with the spring return of the shutoff piston to the rest position. Choose from four optional Loctite Bond-A-Matic Reservoirs that can be used with the Loctite Hand Held Applicator. NO FLOW Type Manual Viscosity Range Low to Medium Size.2" D x 5.2" L x 2.74" W Weight 3.5 oz. (99.2 g) Air Input 60 psi minimum Product Inlet 4 inch Wetted Components Acetal Copolymer, PTFE, PTFE Coated Metal Dispense Patterns Drop, Dot, Bead Used to Dispense Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers Stroke Adjustment Yes Actuation Foot Parts Included () Hand Held Applicator () Applicator Grip () Trigger Lever () Needle Kit () Manual Additional Information For Spare Parts and Accessories, see page 84. For Fluid Compatibility Selector Chart, see page 63. For Dispense Tips, see pages Additional Accessories Sold Separately FLOW 9850 Loctite Applicator Holder / Loctite Bond-A-Matic Reservoirs The RED represents the fluid path " Feed Line Kit 60

63 LOCTITE PNEUMATIC HAND HELD APPLICATOR Item Number: 972 Foot Switch Activated The Loctite Pneumatic Hand Held Applicator (item 972) is a consistent performing, highly reliable, adhesive dispensing valve. It is ergonomically designed for comfortable, application control. It also incorporates a suck- back feature that prevents dripping or stringing. This valve must be used in conjunction with a Loctite brand controller and product reservoir that are foot switch activated. These are sold separately. DISPENSING Hand Held Valves LOCTITE PNEUMATIC HAND HELD APPLICATOR Item Number: 976 Finger Switch Activated The Loctite Pneumatic Hand Held Applicator (item 976) is a consistent performing, highly reliable, adhesive dispense valve. It features a pneumatic trigger actuator that is ergonomically designed for comfort, application control, and a low actuation force to reduce hand fatigue. It also incorporates a suck- back feature that prevents dripping or stringing. This valve must be used in conjunction with a Loctite brand controller and product reservoir, sold separately. Features of Pneumatic Hand Held Applicators: Pistol grip provides comfort and control Low actuation force to reduce hand fatigue Suck- back feature ensures accuracy and control Dispenses products up to 5,000 cp with 4" feed line (standard) Dispenses products up to 80,000 cp with 3 8" feed line (optional) Operational with manual, semi-automatic, and automatic controllers Both hand held applicators are a modular design made up of a product shut-off valve and valve actuator. This type of design provides quick on-line serviceability. The adjustable suck-back feature eliminates stringing and dripping. The shut-off of all hand held applicators takes place mechanically with the spring return of the shut-off piston to the rest position. Henkel offers a selection of Loctite brand product reservoirs that can be used with the Loctite Hand Held Applicators. The RED represents the fluid path. NO FLOW FLOW Type Pneumatic Viscosity Range Low to Medium Size.2" D x 5.2" L x 2.74" W Weight 972: 4.9 oz. (38.9 g) 976: 2 oz. (340 g) Air Input 60 psi min. Product Inlet 4 inch Wetted Components Acetal Copolymer, PTFE, PTFE Coated Metal Dispense Patterns Drop, Dot, Bead Used to Dispense Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers Stroke Adjustment No Actuation 972: Foot (Foot switch is not included with valve, but is 976: Finger (Finger switch is included) included with all controllers) Parts Included () Hand Held Applicator () Applicator Grip () Needle Kit () Manual Additional Information For Spare Parts and Accessories, see pages For Fluid Compatibility Selector Chart, see page 63. For Dispense Tips, see pages Additional Accessories Sold Separately Loctite 300 ml Cartridge Pusher / / / Loctite Bond-A-Matic Reservoirs with Low Level Sensing (976 only) Loctite Digital Multi-Functional Controller (972 only) / 9700 Loctite Integrated Semi-Automatic Controllers 970 Loctite Digital Dispense Controller (972 only) Loctite 3 8" Feed Line Kit 9707 / Loctite Integrated Semi-Automatic Controllers with Low Level Sensors / Loctite Bond-A-Matic Reservoirs (972 only) 9850 Loctite Applicator Holder 6

64 Hand Held Valves DISPENSING PINCH TUBE APPLICATOR LOCTITE VARI-DROP APPLICATOR Item Numbers: 973 and 9732 The Loctite Vari-Drop applicator is low cost, manually controlled pinch valve suitable for dispensing low to medium viscosity products. The adjusting screw allows repeatable dispense from drops to heavy beads. The quantity applied is dependent upon the stroke set for the trigger, and how long the operator holds down the trigger. Accepts a variety of dispensing needles to apply precise amounts of product Low cost Designed with light blocking materials for light curing adhesives Field serviceable The Loctite Vari-Drop Applicator is used to manually dispense Loctite brand products at a controlled rate of flow. The valve is capable of dispensing light to heavy beads or drops. The design is cost effective and user friendly. The operator manually pushes the finger switch down for flow, and releases the switch to discontinue flow. The RED represents the fluid path. NO FLOW FLOW Type Pinch Tube Viscosity Range Low to Medium Size 5 8" H x 5 8" W x 6 4" L Weight.5 oz. (42.5 g) Air Input 00 psi Fluid inlet 4" tube Fluid Pressure 00 psi maximum Fluid Viscosity Range 00 to 80,000 cp Wetted Components PTFE, polyethylene Tubing with PTFE 973: Yes 9732: No Used to Dispense Instant Adhesives, Light Cure/Acrylics, Retaining Compounds, Threadlockers Stroke Adjustment No Actuation Finger Parts Included 973: () Vari-Drop Applicator () 7' x 4" OD PTFE Lined Hose with Hose Guards () Needle Kit () Manual 9732: () Vari-Drop Applicator () Manual Additional Information For Spare Parts and Accessories, see pages For Fluid Compatibility Selector Chart, see page 63. For Dispense Tips, see pages Additional Accessories Sold Separately 9850 Loctite Applicator Holder / Loctite Bond-A- Matic 3000 Dispensers " Feed Line Kit Loctite 300 ml Cartridge Pusher 62

65 Dispense Controller and Reservoir are required with these valves. DISPENSING Hand Held Valves Loctite Brand Hand Held Dispensing Valve Fluid Capability Chart PRODUCT Loctite LV Hand Held Applicator Loctite Manual Hand Held Applicator Loctite Pneumatic Hand Held Applicator Loctite Pneumatic Hand Held Applicator Loctite Vari-Drop Applicator Item Number / 9732 Accelerators Acrylics Activators Anaerobics Cyanoacrylates Inks Oils Paints Primers Reagents Solvents UV & Light Cure Fluids UV Anaerobics Water 63

66 DISPENSING Valves & Pumps Valves & Pumps Loctite brand dispensing valves and pumps are value-added, robust, dispensing valves for adhesive or fluid delivery. Each valve is uniquely designed to meet different manufacturing needs. These valves should be combined with a reservoir and/or a controller. Selection of a Loctite brand valve or pump is based on the chemistry and viscosity of the adhesive or fluid being used and process requirements. PRODUCT Item Number Type Viscosity Range Dispense Patterns Used to Dispense Stroke Adjustment Suck-Back HIGH PRECISION VALVES Loctite Stationary Applicator Valve High Precision Low to Medium Drop, Dot, Bead Gel Instant Adhesives, Instant Adhesives, Retaining Compounds, Threadlockers Yes Yes Loctite Micro Needle Valve High Precision Low to Medium Drop, Dot, Bead, Microdots Light Cure/Acrylics Yes No HIGH PERFORMANCE DIAPHRAGM VALVES Loctite Light Cure Dispense Valve High Performance Diaphragm Low to Medium Drop, Dot, Bead Light Cure/Acrylics, Retaining Compounds, Threadlockers Yes No Loctite Cyanoacrylate Dispense Valve 9803 High Performance Diaphragm Low to Medium Drop, Dot, Bead, Microdots Instant Adhesives, Retaining Compounds, Threadlockers Yes No GENERAL DUTY DIAPHRAGM VALVES Loctite Diaphragm Valve General Duty Diaphragm 0 to 2,500 cp Drop, 2,500 to Dot, Bead 5,000 cp Light Cure/Acrylics Instant Adhesives, Retaining Compounds, Threadlockers No No SPRAY VALVES Loctite Spray Valve Spray Valve Low Spray Primers, Activators, Accelerators Yes No HIGH VISCOSITY FLUID AND PASTE VALVES Loctite Poppet Valve Loctite Stainless Steel Poppet Valve High Viscosity Fluid and Paste Valves Medium to High Drop, Bead Anaerobic Gasketing, Retaining Compounds, Threadlockers Paste Silicones Yes Yes PINCH TUBE VALVE Loctite Shot Miser Dispense Valve Pinch Tube Valve Low to Medium Drop, Dot, Bead Instant Adhesives, Retaining Compounds, Threadlockers No No POSITIVE DISPLACEMENT PUMP Loctite Positive Displacement Pump Positive Displacement Valve Low to Medium Drop Retaining Compounds, Threadlockers, Any single-component, non-moisture-curing, low to medium viscosity fluid (<00,000 cp) Yes No 64

67 DISPENSING Dispense Controller and Reservoir are required with these valves. Valves & Pumps HIGH PRECISION VALVES LOCTITE STATIONARY APPLICATOR VALVE Item Numbers: 973 and 974 The Loctite Stationary Applicator Valve is a slim, lightweight, patented, seal-less dispense valve. It utilizes double-acting, adjustable air to open and close cylinders which allows for precise valve sequencing to meet your most stringent pressure-time dispense requirements. This valve also features adjustable suck-back to eliminate stringing and dripping, and modular design providing for on-line serviceability. It is suitable with all low to medium adhesive viscosities. This valve must be Type used in conjunction with a Loctite brand controller, product Viscosity Range reservoir and dispense tip, sold separately. Size Weight Slim, lightweight, patented seal- less dispense valve Modular design of product shut-off valve and valve actuator provides on- line serviceability Fail safe spring assisted close Suck- back feature eliminates product stringing Double- acting cylinder allows adjustable opening and closing speed for process control Cycle rate exceeds 36 per minute Operational with pressure- time applications Dispenses fluids up to 5,000 cp (item 973) or 80,000 cp (item 974) Product flows to the dispense valve from the reservoir. Adjusting the double- acting cylinders allows control of the valve opening and closing rates. Use of the adjustable suck-back feature eliminates dripping and stringing. These valves can be used in both the stationary or advancing modes. NO FLOW The RED represents the fluid path. FLOW High Precision Low to Medium 7.6" L x 2.4" H 0.75 lbs. Maximum Fluid Pressure 80 psi Air Inlet Port 5 32" Tubing Fitting Air Inlet 60 to 80 psi minute Product Inlet 973: 4" OD Tube 974: 3 8" OD Tube Fluid Outlet 4" UNF, Tip Adapter, Luer-Lok Output Fitting Dispense Patterns Drop, Dot, Bead Used to Dispense Gel Instant Adhesives, Instant Adhesives, Retaining Compounds, Threadlockers Stroke Adjustment Yes Suck-Back Yes Valve Type Pressure-Time Dispense Wetted Components Acetal Copolymer, PTFE and PTFE Coated Metals Air Cylinder Double acting diaphragm cylinder / flow control of both ports / spring return for fail safe function Parts Included () Feed Line () Anti-Bubbler Adapter and Sleeve () Dispense Valve () Needle Kit () Manual Additional Information For Spare Parts and Accessories, see pages For Fluid Compatibility Selector Chart, see pages For Dispense Tips, see pages Additional Accessories Sold Separately 9723 Loctite Single Channel Automatic Controller 970 Loctite Digital Dispense Controller Loctite Digital Multi-Functional Controller / 9700 Loctite Integrated Semi-Automatic Controllers 9707 / Loctite Integrated Semi-Automatic Controllers with Low Level Sensors Loctite 300 ml Cartridge Pusher 975 Loctite Electric Rotorspray / Loctite Bond-A-Matic Reservoirs / Loctite Bond-A- Matic Reservoirs with Low Level Sensors Loctite Advancing Slide (2" Stroke) 65

68 DISPENSING Valves & Pumps LOCTITE MICRO NEEDLE VALVE Item Number: The Loctite Micro Needle Valve is a pneumatically-operated, needle and seat valve that is designed for very small adhesive drops in a pressure-time dispensing system. It is precise down to ml, and has an adjustable stroke control to pinpoint your exact dispense requirement. This valve features the convenience to directly attach filled product syringes ranging in size from 5 to 30 ml for dispensing. Only stainless steel cannula dispense needles should be used for proper dispensing and the valve must be used in conjunction with a Loctite brand controller, product reservoir and dispense tip, sold separately. Dispenses low to medium viscosity UV curing products down to a fraction of a microliter Short opening stroke provides extremely fast, positive shut- off External stroke control adjustment makes it easy for operator to fine tune shot sizes Compact design allows for mounting flexibility and easy integration into automated applications Capable of connecting to syringe barrels as small as 5 ml to 30 ml Type High Precision Change the luer fitting to a tube fitting Viscosity Range Low to Medium and any size pressure reservoir can be used Size 5" L x." D (27 mm L x 28.5 mm D) Designed to be used with high precision Weight 8 oz. (227 g) stainless steel needles Maximum Fluid Pressure 00 psi (7 bar) Application of adhesive using the Loctite Micro Needle Valve is achieved in conjunction with a pressure-time controller and adhesive reservoir system. The controller directs the pressurized air to the actuator of the valve through the inlet air port for a predetermined period of time. This causes the normally closed, needle rod assembly to retract from the seat inside the dispensing tip, allowing the adhesive to flow from the material inlet to the dispensing tip. At the end of the cycle, the controller releases the input air pressure, allowing the spring to return the needle rod back to its original closed position. NO FLOW Fluid Inlet 8" NPT Air Inlet 0-32 UNF-2B Male Luer-Lok Pneumatic Supply Minimum 60 psi (4.8 bar) Maximum 00 psi (7 bar) Product Inlet Fluid Outlet Dispense Patterns Used to Dispense Stroke Adjustment Suck-Back Valve Type Wetted Components 4" NPT 4" UNF Luer-Lok Tip Drop, Dot, Bead Light Cure/Acrylics Yes No Pressure-Time Dispense Acetal Copolymer, Stainless Steel, PTFE Parts Included () Needle Variety Kit Uses stainless steel needles only () Fluid Fitting, 8" NPT x 4" Tube () Product Feed Line, 4" () Air Line Tubing, 5 ft. () Micro Needle Valve () Manual Additional Information For Spare Parts and Accessories, see pages For Fluid Compatibility Selector Chart, see pages For Dispense Tips, see pages Additional Accessories Sold Separately 9723 Loctite Single Channel Automatic Controller / 9700 Loctite Integrated Semi-Automatic Controllers Loctite 0 ml Syringe Air Line Adapter 9707 / Loctite Integrated Semi-Automatic Controllers with Low Level Sensors Loctite 30 ml Syringe Air Line Adapter / / / / / Loctite Bond-A-Matic Reservoirs FLOW Loctite Digital Multi-Functional Controller 970 Loctite Digital Dispense Controller Loctite Advancing Slide (2" Stroke) The RED represents the fluid path Loctite Precision Filter and Regulator (required for use with all pressure-time dispense controllers, other than 9723) Loctite Bracket, Loctite Silicone Grease 66

69 HIGH PERFORMANCE DIAPHRAGM VALVES LOCTITE LIGHT CURE DISPENSE VALVE Item Number: The Loctite Light Cure Dispense Valve (item 98009) is a diaphragm valve that provides high-resolution stroke adjustment and consistent no - drip repeatable dispensing. It is suitable for all low to medium viscosity light curable adhesives, but can also be used for retaining compounds and threadlockers. It has a small profile and simple design that minimizes space requirements and facilitates routine preventative maintenance. This valve must be used in conjunction with a Loctite brand controller, product reservoir and dispense tip, sold separately. LOCTITE CYANOACRYLATE DISPENSE VALVE Item Number: 9803 The Loctite Cyanoacrylate Dispense Valve is a diaphragm valve that provides high-resolution stroke adjustment and consistent, no -drip, repeatable dispensing. It is suitable for all low to medium viscosity cyanoacrylate adhesives but can also be used for retaining compounds and threadlockers. It has a small profile and simple design that minimizes space requirements and facilitates routine preventative maintenance. This valve must be used in conjunction with a Loctite brand controller, product reservoir and dispense tip, sold separately. Features of Dispense Valves: Compact size and weight Adjustable fluid flow control Fail safe, air to open, spring close Positive shutoff, no seals Bubble - free, no- drip dispensing Field serviceable Easy cleaning without valve de-mounting Cycle rate exceeds 500 per minute Product flows to the dispense valve from the reservoir. Flow rate is adjusted by turning the flow control dial on top of the valve. The valves can be used in both the stationary or advancing modes. NO FLOW FLOW Loctite Light Cure Dispense Valve Type High Performance Diaphragm Viscosity Range Low to Medium Size 3.090" x.060" diameter Weight 4.5 oz. (28 g) Maximum Fluid Pressure 70 psi Fluid Inlet 8" NPT Fluid Outlet 4"-28 UNF, Tip Adapter, Luer-Lok Output Fitting Air Inlet Port 4" Tube Fitting Air Input 70 to 90 psi Air Cylinder Single Acting, Spring Return, Stroke Control, Aluminum, Hard Coated Finish Dispense Patterns Drop, Dot, Bead, Microdot Used to Dispense 98009: Light Cure/Acrylics, Retaining Compounds, Threadlockers 9803: Gel Instant Adhesives, Retaining Compounds, Threadlockers Stroke Adjustment Yes Suck-Back No Valve Type Diaphragm Wetted Components 98009: Chamber: Acetal Copolymer Diaphragm: Ultra High Molecular Weight Irradiated Polyethylene 9803: Chamber: Ultra High Molecular Weight Polyethylene Diaphragm: Ultra High Molecular Weight Irradiated Polyethylene Mounting Hole () 0-32 UNF Parts Included () 5 ft. Air Line Tubing (attached to valve) () Needle Kit () 6 ft. Product Tubing, 4" OD, PTFE Lined () Valve Mount Screw () Valve Assembly () Manual Additional Information For Spare Parts and Accessories, see pages For Fluid Compatibility Selector Chart, see pages For Dispense tips, see pages Additional Accessories Sold Separately 9723 Loctite Single Channel Automatic Controller 970 Loctite Digital Dispense Controller / 9700 Loctite Integrated Semi-Automatic Controllers 9707 / Loctite Integrated Semi-Automatic Controllers with Low Level Sensors 9803 Loctite Cyanoacrylate Dispense Valve / Loctite Bond-A- Matic Reservoirs / Loctite Bond-A- Matic Reservoirs with Low Level Sensors DISPENSING Valves & Pumps The RED represents the fluid path Loctite Digital Multi-Functional Controller Loctite 300 ml Cartridge Pusher Loctite Advancing Slide (2" Stroke) 67

70 DISPENSING Valves & Pumps GENERAL DUTY DIAPHRAGM VALVES LOCTITE DIAPHRAGM VALVE Item Numbers: 9735 and 9736 The Loctite Diaphragm Valve is a pneumatically-activated dispense valve that utilizes a floating PTFE diaphragm for consistent, trouble-free dispensing. It is suitable for all low to medium viscosity light curable adhesives, retaining compounds, and threadlockers. The valve has a simple design that minimizes space requirements and facilitates routine preventative maintenance. It is ideal to support automatic rotospray and electric rotorspray applications, and must be used in conjunction with a Loctite brand controller, product reservoir and dispense tip, sold separately. Cost effective valve for use with pressure- time dispense systems Modular design and floating diaphragm allow for easy cleaning or repair Fail safe, spring assisted close Internal components are made of PTFE to prevent premature curing Flow rates can be increased with use of a 3 8" feed line Available in low viscosity (item 9735) and medium viscosity (item 9736) versions Application of adhesive using the Loctite Diaphragm Valve is achieved in conjunction with a pressure-time controller and adhesive reservoir system. The opening of the diaphragm takes place by pressurizing the internal single -acting cylinder and piston. Initiating a dispense cycle causes the piston to lift from the diaphragm. The adhesive pressure then pushes the diaphragm away from the flow path, allowing the adhesive to flow to the dispense needle. At the end of the dispense time, pressure is released and an internal spring reseats the diaphragm over the flow path. The amount of adhesive applied is controlled by the dispense time, air pressure, and dispense needle gauge size. NO FLOW Type General Duty Diaphragm Viscosity Range 0 to 2,500 cp 2,500 to 5,000 cp Size 5" L x.25" D (27 mm L x 32 mm D) Weight 0.5 oz. (300 g) Maximum Fluid Pressure 7 to 58 psi (0.5 to 4 bar) Fluid Inlet 4" Tubing or upgrade to 3 8" (Item 97220) Air Inlet 5 32" Tubing Pneumatic Supply Minimum 73 psi (5 bar) Maximum 00 psi (7 bar) Product Inlet 9735: 4" OD 9736: 8" OD Fluid Outlet Dispense Patterns Used to Dispense Stroke Adjustment Suck-Back Valve Type Wetted Components 4" UNF Luer-Lok Tip Drop, Dot, Bead Light Cure/Acrylics, Retaining Compounds, Threadlockers No No Pressure-Time Dispense Acetal, Stainless Steel, PTFE Coated Metals () Diaphragm Valve () Product Feed Line, Parts Included 4" inch () Needle Variety Kit () Manual Additional Information For Spare Parts and Accessories, see pages For Fluid Compatibility Selector Chart, see pages For Dispense Tips, see pages Additional Accessories Sold Separately Loctite Shot Miser Reservoir Loctite Shot Miser Controller 9723 Loctite Single Channel Automatic Controller / / / / / Loctite Bond-A-Matic Reservoirs FLOW / 9700 Loctite Integrated Semi-Automatic Controllers 9707 / Loctite Integrated Semi-Automatic Controllers with Low Level Sensors The RED represents the fluid path Loctite Digital Multi-Functional Controller 970 Loctite Digital Dispense Controller 975 Loctite Electric Rotorspray 978 / 979 Loctite Advancing Slides 68

71 SPRAY VALVES LOCTITE SPRAY VALVE Item Number: LOCTITE SPRAY VALVE CONTROLLER Item Number: 9852 The Loctite Spray Valve (item 98520) provides an effective solution for automatic spraying of low viscosity primers, accelerators and activators up to,200 cp, with high precision and long term reliability. It features an external stroke adjustment, providing consistent performance over a wide range of operating conditions. The high performance needle and seat design ensures effective control of over-spray and nozzle dripping. This valve is most effectively controlled using the Loctite Spray Valve Controller (item 9852), providing digital pressure control of both on/off timing and atomization air, sold separately. Loctite Spray Valve High precision, short stroke, needle and seat design providing repeatable spray pattern performance Air pressure and stroke adjustment allow a wide range of spray pattern coverage control Full stainless steel body and wetted parts provide long term performance and durability Cycle rate up to 600 per minute Easy cleaning and servicing 0.046" nozzle diameter (standard) provides consistent round full cone pattern Optional 0.04" and 0.028" diameter nozzle kits for lower spray pattern applications Loctite Spray Valve Controller Microprocessor -based, timed controller Fully independent valve/open close and atomization air supply 3 separate timed sequences pre-spray, valve on, post- spray/ valve off Timed or manual mode with foot pedal control All time modes maintained in memory with AC power disconnected Product flows from a reservoir under air pressure as provided by the Loctite Spray Valve Controller. The controller also provides air to open/close the valve and a separate atomizing air source to the Loctite Spray Valve nozzle assembly. Timing and pressure controls for atomizing air, fluid line pressure, valve stroke adjustment, height from surface, and material viscosity can be adjusted to optimize required dispense quantity and coverage pattern. Atomizing Air OFF NO FLOW The RED represents the fluid path. Atomizing Air ON FLOW Loctite Spray Valve Type Spray Valve Viscosity Range Up to,200 cp Air Pressure Supply 60 to 00 psi Fluid Inlet Port 8" NPT Weight 0.8 lbs. (385 g) Spray Height / Pattern Diameter Dispense Pattern Used to Dispense Stroke Adjustment Suck-Back Valve Type Wetted Components Parts Included "/0.25", 2"/ 0.50", 3"/ 0.75", 4"/.5", 5"/3" (0.046 nozzle) Spray Circular Accelerators, Activators, Primers Yes No Pressure-Time Dispense 304 Stainless Steel () Valve Mounting Bracket with screw () Valve Assembly () Fluid Line Assembly () Air Line Assembly () Operation Manual () Hex Key () Seat Removal Tool 9852 Loctite Spray Valve Controller Power Source 20 VAC Air Supply 8" Tube Fitting 00 psi max Weight 5.5 lbs. Dimensions 2.5" H x 2.4" L x 7.6" D Parts Included () Controller Unit & Power Cord () Foot Pedal () Air Supply Line & Filter 4 ft. Additional Information For Spare Parts and Accessories, see pages For Fluid Compatibility Selector Chart, see pages Additional Accessories Sold Separately " Nozzle Kit " Nozzle Kit Loctite Replacement Foot Switch 9852 Loctite Spray Valve Controller. (See page 7) / Loctite Bond-A- Matic Reservoirs with Low Level Sensors Loctite Spray Valve / Loctite Bond-A-Matic Reservoirs DISPENSING Valves & Pumps 69

72 Valves & Pumps DISPENSING HIGH VISCOSITY FLUID AND PASTE VALVES LOCTITE POPPET VALVES Item Numbers: and LOCTITE STAINLESS STEEL POPPET VALVE Item Number: The Loctite Poppet Valves are designed to dispense Loctite brand high viscosity anaerobic form- in- place gasketing products, structural acrylics, and silicones. The valves are typically used in conjunction with a positive displacement pump or a pressure- time system. They feature a suck-back capability and can operate at fluid pressures up to 625 psi. Item uses dispense nozzles with a bayonet style mounting that improves nozzle end location and can withstand the high fluid pressures required of high viscosity fluid dispensing. Items and are equipped with a 8" NPT outlet for Luer-Lok and standard needle dispensing. All valves have stroke adjustment capability and are treated with a proprietary Loctite coating to prevent premature adhesive curing. Poppet design gives valve suck- back feature Bayonet type mounting of nozzles provides end location repeatability Handles product pressures up to 625 psi Positive mounting surface High strength plastic material versions are specially treated to be inert to Loctite brand products Stainless steel version is also specially treated and is recommended for abrasive and silicone products Loctite Stainless Steel Poppet Valve and Loctite Poppet Valves Use the Loctite Poppet Valve to apply product in drops and beads with a semi or fully automatic dispensing system. The valve can be used in both the stationary or advancing modes. They may be used with the Loctite Pump-A-Bead II or any other dispense system that can provide a source of pressurized product and a 4-way pneumatic valve. NO FLOW FLOW Type High Viscosity Fluids and Pastes Viscosity Range Medium to High anaerobics up to Low Viscosity silicone products Size 5.28" H x 2.00" D Weight.3 lb. (0.59 kg) valve plus fittings and tubing Maximum Fluid Pressure Should not exceed 625 psi Air Input 60 psi Inlet 4" NPT Dispense Tip Style : Bayonet Style and 98262: 8" NPT for Luer-Lok dispense tips Used to Dispense Anaerobic Gasketing, Retaining Compounds, Modified Silanes, Silicones Threadlockers Dispense Patterns Bead, Drop Stroke Adjustment Yes Suck-Back Yes Valve Type Pressure-Time Dispense Wetted Components Acetal Copolymer treated with a proprietary Loctite brand process Parts Included () Acetal Copolymer Body or Stainless Steel Poppet Valve with: (2) 4' Control Air Tubing () 4' Product Supply Tubing () Accessory Kit () Manual Additional Information For Spare Parts and Bayonet type needles, see pages For Fluid Compatibility Selector Chart, see pages For Luer-Lok Dispense Tips, see pages Additional Accessories Sold Separately The RED represents the fluid path Loctite Pump-A-Bead Loctite Advancing Slide (2" Stroke) 70

73 PINCH TUBE VALVE LOCTITE SHOT MISER DISPENSE VALVE Item Number: The Loctite Shot Miser Dispense Valve is an economical pinch tube style valve that features an adjustable stroke for enhanced shot size control. This valve has a disposable fluid path for fast, easy and low cost replacement. This valve must be used in conjunction with a Loctite brand controller and product reservoir, sold separately. Pneumatically- actuated automatic dispense valve Pinch- tube disposable fluid path for fast, easy and low cost maintenance Dispenses dots or beads 4" diameter product feed tube Adjustable valve stroke for enhanced shot size control Replaceable pneumatic actuator Integral Luer- Lok fitting accepts all Loctite brand dispense needles Application of adhesive using the Loctite Shot Miser Dispense Valve is achieved in conjunction with a pressure- time controller and adhesive reservoir system. The opening and closing of the valve is controlled by the system s timer controls. When the dispense cycle is initiated, the piston pulls away from the pinch tube channel in the valve, opening the flow path, and allowing adhesive to pass. At the end of the dispense cycle, pressure is then reapplied to the piston, closing the flow path. The amount of dispensed adhesive is controlled by adjustment of air pressure, valve open time, and the size of the dispensing needle. NO FLOW Type Viscosity Range Size Weight Maximum Fluid Pressure Fluid Inlet Outlet Dispense Patterns Used to Dispense Stroke Adjustment Suck-Back Valve Type Wetted Components Parts Included Pinch Tube Valve Low to Medium 5.2" W x.75" L x 6.4" H 0.5 lbs. 00 psi 4" Tube Luer-Lok Tip Dot, Drop, Bead Instant Adhesives, Retaining Compounds, Threadlockers No No Pressure-Time Dispense Acetal Copolymer, Stainless Steel, PTFE Coated Metals () Dispense Valve with 4" diameter Product Feed Tube () Dispense Needle Sample Kit () Valve Air Line () Manual Additional Information For Spare Parts and Accessories, see pages For Fluid Compatibility Selector Chart, see pages For Dispense Tips, see pages Additional Accessories Sold Separately 9723 Loctite Single Channel Automatic Controller / 9700 Loctite Integrated Semi-Automatic Controllers / Loctite Bond-A-Matic Reservoirs DISPENSING Valves & Pumps The RED represents the fluid path. FLOW 970 Loctite Digital Dispense Controller Loctite Digital Multi-Functional Controller 9707 / Loctite Integrated Semi-Automatic Controllers with Low Level Sensors Loctite 300 ml Cartridge Pusher / Loctite Bond-A- Matic Reservoirs with Low Level Sensors Loctite Advancing Slide (2" Stroke) 7

74 DISPENSING Valves & Pumps POSITIVE DISPLACEMENT PUMP LOCTITE POSITIVE DISPLACEMENT PUMP Item Number: The Loctite Positive Displacement Pump features a patented, seal-less design. It is specifically designed to dispense Loctite brand threadlockers and retaining compounds in rotospray applications with a high degree of precision. The dispense capability of this pump is 0.02 to 0.4 cc. It has a modular design for easy maintenance. For rotospray applications, it is normally used with the Loctite Digital Multi- Function Controller (item ). Positive displacement Pneumatically- operated Designed for compatibility with Loctite brand rotospray workstations Modular design of product shut- off valve and valve actuator provides on- line serviceability Cycle rate for low viscosity products exceeds 20 per minute Small, easy-to-use design Adjustable stroke to control the amount of material dispensed Compatible with a wide range of fluids Repeatable and consistent delivery of product Type Viscosity Range Use the Loctite Positive Displacement Pump for rotospraying low to medium viscosity fluids. Typically, this unit is used in conjunction with a gravity feed reservoir. The gravity feed reservoir will transfer the material from the storage tank to the pump, which supplies material to the dispensing area. Size Weight Air Input Product Line Feed Fluid Capacity Cycle Speed Dispense Patterns Used to Dispense Stroke Adjustment Suck-Back Valve Type Wetted Components Parts Included Positive Displacement Pump Low to Medium 9.5" H x.88" D (maximum) / 2.6" W (with connections).7 lbs. 60 to 90 psi 3 8" OD before pump, 4" OD after pump 0.02 to 0.40 cc per shot 2 cycles per second maximum (adjustable) Drop Retaining Compounds, Threadlockers, Any single-component, non-moisture-curing, low to medium viscosity fluid (<00,000 cp) Yes No Positive Displacement Acetal Copolymer, Stainless Steel, and PTFE Coated Metals () Positive Displacement Pump () Feed Line Accessory Kit () Mounting Bracket () Air Line Kit () Manual Additional Information For Spare Parts and Accessories, see pages For Fluid Compatibility Selector Chart, see pages For Dispense Tips, see pages Additional Accessories Sold Separately NO FLOW FLOW The RED represents the fluid path Loctite Digital Multi-Functional Controller Loctite 4 Liter Gravity Feed Reservoir Loctite Rotospray 9000 Applicator LOCTITE ROTOSPRAY 9000 APPLICATOR The Loctite Rotospray 9000 Applicator is a pneumatically- powered applicator used for applying 360 degree beads of a fluid on the inside diameter of any surface or threaded hole. Common materials applied are retaining compounds, threadlockers, activators/primers, and oils. Common applications are engine cup plug sealing, bearing retaining, and motor magnet bonding. Rotospray applicators can be used in a variety of applications and configurations, and are typically used in conjunction with the Loctite Positive Displacement Pump (item ) and Loctite 4 Liter Gravity Feed Reservoir (item ). If you have an application requiring an internal 360 degree bead, contact the Henkel technical information department at -800-LOCTITE, for the right rotospray applicator for your application. 72

75 DISPENSING Dispense Controller and Reservoir are required with these valves. Valves & Pumps Loctite Brand Valve & Pump Fluid Capability Chart PRODUCT Loctite Stationary Applicator Valve Loctite Micro Needle Valve Loctite Light Cure Dispense Valve Loctite Cyanoacrylate Dispense Valve Loctite Diaphragm Valve Item Numbers 973 / / 9736 Accelerators Acrylics Activators Anaerobics Anaerobic Gasketing Cyanoacrylates Inks Lubricants Modified Silanes Non-Abrasive Greases Oils One-Part Epoxies Paints Primers Reagents Silicones Solvents UV & Light Cure Fluids UV Anaerobics Water 73

76 Valves & Pumps DISPENSING Loctite Brand Valve & Pump Fluid Capability Chart PRODUCT Loctite Spray Valve Loctite Poppet Valve Loctite Stainless Steel Poppet Valve Loctite Shot Miser Dispense Valve Loctite Positive Displacement Pump Item Numbers / Accelerators Acrylics Activators Anaerobics Anaerobic Gasketing Cyanoacrylates Inks Lubricants Modified Silanes Non-Abrasive Greases Oils One-Part Epoxies Paints Primers Reagents Silicones Solvents UV & Light Cure Fluids UV Anaerobics Water 74

77 Pail Pumps Henkel offers Loctite brand pail pump systems to effectively dispense both low viscosity fluids and high viscosity pastes from 5 and 55 gallon containers. These systems are very durable and can be relied on for long term performance in the toughest working environments. These systems are typically integrated into a complete dispensing system for a single component product, or used as a feed system for multiple component products. DISPENSING Pail Pumps LOCTITE LOW VISCOSITY FLUID PUMPS The Loctite Low Viscosity Fluid Pumps are specifically designed to dispense self- leveling products packaged in 5 gallon pails up to 55 gallon drums or tanks. The various pump ratios are suited for pumping low to medium viscosity fluids. These pumps are air operated and deliver various product output volumes determined by the pump ratio and input pressure. Choice of two pump and seal materials Carbon steel with Viton seals or inert metal with EPR seals 5 gallon pail or 55 gallon drum or tank capability :, 3:, or 4: pump ratio versions (liquid to air pressure) These units, when configured with the necessary air and product hoses, air and fluid regulators, dispense valves, tips and fittings, will pump self-leveling, low to medium viscosity fluids from 5 gallon pails up to 55 gallon drums or tanks. Typical Fluids Handled and Parts Supplied Carbon Steel Systems: lubricants, epoxies, urethanes Inert Metal with EPR seals: lubricants, epoxies, anaerobics, acrylics, light cure acrylics, epoxy hardener, urethanes, water- based products Loctite Brand Parts Supplied (Highlighted in Purple in Component Diagram Below) Low Viscosity Fluid Pump with appropriate tube for either 5 gallon or 55 gallon as ordered E Additional Information See page 77 to select appropriate hosing, dispense valves, fluid regulators, air filters, dispense tips, and other accessories to complete your Loctite Low Viscosity Fluid Pump System. Loctite Low Viscosity Fluid Pump Component Diagram Number designation highlights item type in the accessories chart on page 77. A 3 6 2B 6 Item Number Ratio Output per Stroke Material Container Maximum Product Viscosity (cp) : 2.9 in 3 Carbon Steel 55 Gallon : 7.9 in 3 Carbon Steel 55 Gallon 50, : 7.9 in 3 Inert Metal 55 Gallon 50, : 7.9 in 3 Carbon Steel 5 Gallon 50, : 7.9 in 3 Inert Metal 5 Gallon 50, :.7 in 3 Carbon Steel 55 Gallon 250, :.7 in 3 Inert Metal 55 Gallon 250, :.7 in 3 Carbon Steel 5 Gallon 250, :.7 in 3 Inert Metal 5 Gallon 250, B Manual System Automatic System (Secondary Pressure Regulation) B

78 DISPENSING Pail Pumps LOCTITE HIGH VISCOSITY PASTE PUMP SYSTEMS The Loctite High Viscosity Paste Pump Systems are specifically designed to dispense paste products packaged in 5 gallon opentop pails up to 55 gallon drums. The various pump ratios are suited for pumping medium to high viscosity paste products. The high viscosity paste pump systems are fully assembled systems consisting of an air motor, pump tube, and pressure ram. Choice of three pump and seal materials Carbon steel with polyurethane seals, carbon steel with inert seals, or inert metal 5 gallon open-top pails or 55 gallon drum capability 22:, 44:, or 64: pump ratio versions (liquid to air pressure) These units, when configured with the necessary air and product hoses, air and fluid regulators, dispense valves, tips and fittings, will pump medium to high paste products from 5 gallon open-top pails up to 55 gallon drums. Typical Fluids Handled and Parts Supplied Carbon Steel Systems: lubricants, epoxies, urethanes Carbon Steel Systems (with inert seals): RTV silicones, lubricants, epoxy resins, epoxy hardeners, and urethanes Inert Metal Systems: lubricants, epoxies, anaerobics, acrylics, light cure acrylics, epoxy hardeners, urethanes, water- based products Loctite Brand Parts Supplied - (Highlighted in Purple in Component Diagram Below) () Air Motor A () Single Post Primer/Follower plate 5 gallon systems D () Twin Post Primer/Follower Plate 55 gallon systems C () High Viscosity Pump Tube B Additional Information See page 77 to select appropriate hosing, dispense valves, fluid regulators, air filters, dispense tips, and other accessories to complete your Loctite High Viscosity Paste Pump System. Loctite High Viscosity Paste Pump Component Diagram Number designation highlights item type in the accessories chart on page A 4 Item Number 3 2B 3 Ratio Output per Stroke 5 Material 6 Container Maximum Product Viscosity (cp) : 6.7 in 3 Carbon Steel 55 Gallon 500, : 6.7 in 3 Carbon Steel 5 Gallon 500, : 6.7 in 3 Inert Metal 55 Gallon 500, : 6.7 in 3 Inert Metal 5 Gallon 500, : 6.7 in 3 Carbon Steel w/inert Seals 5 Gallon 500, : 6.7 in 3 Carbon Steel w/inert Seals 55 Gallon 500, : 6.7 in 3 Carbon Steel 55 Gallon,000, : 6.7 in 3 Carbon Steel 5 Gallon,000, : 6.7 in 3 Inert Metal 55 Gallon,000, : 6.7 in 3 Inert Metal 5 Gallon,000, : 6.7 in 3 Carbon Steel w/inert Seals 5 Gallon,000, : 6.7 in 3 Carbon Steel w/inert Seals 55 Gallon,000, : 4.6 in 3 Carbon Steel 55 Gallon 4,000, : 4.6 in 3 Carbon Steel 5 Gallon 4,000, : 4.6 in 3 Inert Metal 55 Gallon 4,000, : 4.6 in 3 Inert Metal 5 Gallon 4,000, : 4.6 in 3 Carbon Steel w/inert Seals 5 Gallon 4,000, : 4.6 in 3 Carbon Steel w/inert Seals 55 Gallon 4,000, Manual System 6 A 3 2A 6 D B 4 5 2B 5 B A 3 3 Automatic System (Secondary Pressure Regulation) C NOTES:. Hoses have Female JIC Swivel Fittiings on both ends. 2. ALL Fittings are stainless steel unless otherwise noted. 76

79 Loctite Brand Pail Pump Accessories Item PRODUCT Number HIGH VISCOSITY PASTE PUMP COMPONENTS A B PUMP PRIMERS C D Description " Air Motor For 22: Systems, 30 to 00 psi " Air Motor For 44: and 64: Systems, 30 to 00 psi CS Pump Tube For 22: and 44: Systems Inert Pump Tube For 22: and 44: Systems CS Pump Tube For 64: Systems Inert Pump Tube For 64: Systems CS Pump Tube with Inert Seals For 22: and 44: Systems CS Pump Tube with Inert Seals For 64: Systems CS, 55 gallon Twin Post Primer Inert, 55 gallon Twin Post Primer CS, 5 gallon Single Post Primer Inert, 5 gallon Single Post Primer SYSTEM HOSES All Hoses have Female JIC Swivel Fittings 2A 2B HOSE FITTINGS Stainless Steel SYSTEM ACCESSORIES High Pressure 3/4" x 6' SS, PTFE Lined 5,000 psi max High Pressure 3/4" x 2' SS, PTFE Lined 5,000 psi max High Pressure 3/4" x 24' SS, PTFE Lined 5,000 psi max High Pressure " x 6' SS, PTFE Lined 5,000 psi max High Pressure " x 2' SS, PTFE Lined 5,000 psi max High Pressure " x 24' SS, PTFE Lined 5,000 psi max Medium Pressure Hose 3/8" x 6' 2,250 psi 9890 Medium Pressure Hose 3/8" x 2' 2,250 psi 989 Medium Pressure Hose 3/8" x 24' 2,250 psi 9892 Medium Pressure Hose /2" x 6' 2,000 psi 9893 Medium Pressure Hose /2" x 2' 2,000 psi 9894 Medium Pressure Hose /2" x 24' 2,000 psi 9895 Medium Pressure Hose 3/4" x 6',500 psi 9896 Medium Pressure Hose 3/4" x 2',500 psi 9897 Medium Pressure Hose 3/4" x 24',500 psi 9898 Medium Pressure Hose " x 6',500 psi 9899 Medium Pressure Hose " x 2',500 psi Medium Pressure Hose " x 24',500 psi 9892 " JIC M x 3/4" MNPT Connector /4" JIC M x 3/4" MNPT Connector /4" JIC M x /2" MNPT Connector /2" JIC M x 3/4" MNPT Connector /2" JIC M x /2" MNPT Connector /2" JIC M x /4" MNPT Connector /8" JIC M x /2" MNPT Connector /8" JIC M x 3/8" MNPT Connector /8" JIC M x /4" MNPT Connector /8" JIC M x 3/8" MNPT Elbow 9893 /2" JIC M x /4" MNPT Elbow /2" JIC M x /2" MNPT Elbow /4" JIC M x 3/4" MNPT Elbow /4" JIC M x /2" MNPT Elbow " JIC M x 3/4" MNPT Elbow /4" FNPT x /4" MNPT Reducing Adapter /4" FNPT x /2" MNPT Reducing Adapter /2" FNPT x /8" MNPT Reducing Adapter /2" FNPT x /4" MNPT Reducing Adapter /8" FNPT x /8" MNPT Reducing Adapter /8" FNPT x /4" MNPT Reducing Adapter Pump Hoist Pump Stop Gallon Drum Cover Gallon Pail Cover Low Level Cut-off 55 Gallon Microswitch Low Level Wall Mount Kit for Ball Valves Item PRODUCT Number DISPENSE VALVES Description Max. Inlet Pressure Operating Pressure Inlet/Outlet Fitting Size High Viscosity Valve Mountable 4000 psi 0 to 4,000 psi /4" FNPT x /4" FNPT High Viscosity Hand Gun Pistol Grip 4000 psi 0 to 4,000 psi /4" FNPT x /4" FNPT High Viscosity Hand Gun In Line 3400 psi 0 to 3,400 psi /4" FNPT x /4" FNPT Poppet Valve 625 psi 0 to 625 psi /4" Tube x /8" NPT Poppet Valve 625 psi 0 to 625 psi /4" Tube x Bayonet Needle Poppet Valve 625 psi 0 to 625 psi /4" Tube x /8" NPT 973 Stationary Valve 80 psi 0 to 80 psi /4" Tube x /4" Stationary Valve 80 psi 0 to 80 psi 3/8" Tube x /4" Light Cure Valve 70 psi 0 to 70 psi /8" FNPT x /4"-28 FLUID PRESSURE REGULATION AND ACCESSORIES 9896 Primary Fluid Regulator Assembly 5,000 psi 250 to 4,500 psi 3/4" FNPT x 3/4" FNPT 9896 INCLUDES THE FOLLOWING ITEMS THAT ARE AVAILABLE INDIVIDUALLY Primary Fluid Regulator 5,000 psi 250 to 4,500 psi 3/4" FNPT x 3/4" FNPT Gauge and Isolator Assembly 5,000 psi 0 to 5,000 psi 3/4" MNPT x 3/4" FNPT Secondary Fluid Regulator ,625 psi 0 to 725 psi /4" MNPT x /4" FNPT Assembly INCLUDES THE FOLLOWING ITEMS THAT ARE AVAILABLE INDIVIDUALLY Secondary Regulator 0 to,000 psi 3,625 psi 0 to 725 psi /4" BSPP Female Gauge and Isolator Assembly,000 psi 0 to,000 psi /8" MBSPP Low Viscosity Fluid Pump Regulator,250 psi 30 to 200 psi 3/8" FNPT x 3/8" FNPT Low Viscosity Fluid Pump Regulator & Gauge 750 psi 5 to 30 psi 3/8" FNPT x 3/8" FNPT Particle Filter Assembly Includes two high pressure 5,000 psi gauge assemblies Purge Tube Kit For Particle Filtration (Includes 2 isolation valves) 0 to 5,000 psi 3/4"FNPT x 3/4" FNPT 3/4" MNPT x 3/4"FNPT Mounting bracket 9896 to 5 gallon primer AIR SUPPLY FILTERS AND FITTINGS Airline Filter/Regulator psi 0 to 50 psi /8" FNPT x /8"FNPT with Pressure Gauge Fitting to Primer 3 Way Valve /8" MNPT x /4"MNPT FRL Air Filter Assembly psi 0 to 00 psi /2" FNPT x /2" FNPT For Air Motor Inlet Fitting FRL Outlet to Air Motor Inlet 3/4" MNPT x /2" MNPT Fitting FRL Inlet to External Air Supply /4" MNPT x /2" MNPT DISPENSE TIPS /4" MNPT, " long x 0.50" ID /4" MNPT, " long x 0.094" ID /4" MNPT, " long x 0.063" ID /4" MNPT, 2.5" long x 0.50" ID /4" MNPT, 2.5" long x 0.094" ID /4" MNPT, 2.5" long x 0.063" ID /8" MNPT, " long x 0.50" ID /8" MNPT, " long x 0.094" ID /8" MNPT, " long x 0.063" ID /8" MNPT, 2.5" long x 0.50" ID /8" MNPT, 2.5" long x 0.094" ID 9898 /8" MNPT, 2.5" long x 0.063" ID Adapter for /8" MNPT Tip Nozzles, /8" NPS x /4" NPS mm ID Tapered SS Nozzle, /8"-28 BSPP mm ID Tapered SS Nozzle, /8"-28 BSPP mm ID Tapered SS Nozzle, /8"-28 BSPP mm ID Tapered SS Nozzle, /8"-28 BSPP mm ID Tapered Acetal Copolymer Nozzle, /8"-28 BSPP mm ID Tapered Acetal Copolymer Nozzle, /8"-28 BSPP mm ID Tapered Acetal Copolymer Nozzle, /8"-28 BSPP mm ID Tapered Acetal Copolymer Nozzle, /8"-28 BSPP mm ID Tapered Aluminum Nozzle, /8"-28 BSPP mm ID Tapered Aluminum Nozzle, /8"-28 BSPP mm ID Tapered Aluminum Nozzle, /8"-28 BSPP mm ID Tapered Aluminum Nozzle, /8"-28 BSPP Adapter for /8"-28 BSPP Nozzles, /8" BSPP x /4" NPS DISPENSING Pail Pumps 77

80 DISPENSING Monitoring Systems Monitoring Systems These state-of- the- art detection systems allow real time process monitoring of dispense cycles. Whether you re looking to determine the presence of adhesive via fluorescence detection, or the amount of adhesive dispensed for an individual dispense nozzle, Henkel has the system that will get the job done with a high degree of precision and reliability. LOCTITE FLUORESCENCE DETECTOR Item Number: Designed for the detection of fluorescent adhesives, this unit connects to an in-house power supply and PLC for monitoring of dispense processes utilizing fluorescent adhesives and sealants. Three interchangeable lenses are available for various detection distances. A 00,000 hour LED life ensures consistent and long-term process monitoring. 00,000 hours LED life 250 microsecond maximum response time between detection points 3 lens options (sold separately) allow for various detection distances Common light output and fluorescence detection path Equipped with a learn mode feature, allowing the programming of part detection with minimal effort NPN and PNP output capability, allowing easy interface An internal Light Emitting Diode (LED) illuminates adhesives and sealants that contain fluorescent additives. When adhesive is not detected on the illuminated part, an analog or digital signal is transmitted to indicate an insufficient amount. The Loctite Fluorescence Detector is designed for easy interface with most analog or PNP and NPN digital detection systems. Dimensions Weight Input Voltage Output Voltage NPN/PNP: Response Time Switching Frequency Light Source Spot Size Parts Included 3." L x 2.3" W x.2" D 0.68 lbs. 0 to 30 volts DC current (80 to 300) ma Analog Output 0 to 5.5 volts into 2.2 ohms 0 ohms pull up/down resistance 250 microsecond maximum 2 khz LED 00,000 hours life 9802: 9 mm Lens mm Spot 9803: 28 mm Lens 0 mm Spot 980: 50 mm Lens 2 mm Spot () Fluorescence Detector (Lenses Sold Separately) () 4-Conductor Cable with M2 Connector () Manual Additional Accessories Sold Separately mm Lens mm Lens mm Lens Loctite 4-Conductor Cable with M2 connector 78

81 LOCTITE IN-LINE FLOW MONITOR Item Number: 972 The Loctite In-Line Flow Monitor (item 972), when integrated with the Loctite Single Channel Automatic Controller (item 9723), provides an economical, yet effective, approach to adhesive dispense monitoring. Pressure changes due to air entrapment, broken or blocked nozzles, or substrate contact can be effectively monitored by the system with a high degree of accuracy and repeatability. All out of tolerance dispense cycles result in error messages being displayed on the controller display. (When integrated with the Loctite Single Channel Controller 9723) Effective dispense monitoring to detect: Air bubbles Clogged or broken dispense tips, or tip-substrate contact Changes in amount of adhesive dispensed 3 pre-set dispense tolerances or Power Input customizable from to 99% Power Output PLC or PC integration to provide SPC data analysis Dimensions Weight Required System Components Sold Separately 24 VDC to 0 VDC 3" W x 5.5" H x 2.25" D 0.5 lbs. Additional Accessories Sold Separately DISPENSING Monitoring Systems 9723 Loctite Single Channel Automatic Controller Provides dispense control and tolerance monitoring Valve Adapter Valve body adapter for Loctite dispense valves (Item Numbers 973 / 974) Valve Adapter Valve body adapter for Loctite dispense valves (Item Numbers / 9803) Sensor and Cable Pressure sensor and cable for dispense valve interface Loctite Light Cure Dispense Valve / Loctite Bond-A-Matic Reservoirs 9803 Loctite Cyanoacrylate Dispense Valve 973 / 974 Loctite Stationary Applicator Valves / Loctite Bond-A-Matic Reservoirs with Low Level Sensors LOCTITE FLUID WAVEFORM ANALYZER,SIGNATURE SERIES Custom Equipment Loctite Fluid Waveform Analyzers are state- of- the- art fluid detection systems for use where high quality production and data inspection are desired. Available through the custom equipment group of Henkel, these dispense inspection systems use conclusive real time data acquisition to detect plugged and broken dispense nozzles, nozzle voids, no dispense, low pressure (under- sized beads), high pressure (over- sized beads), and air bubbles. The resulting output is a pressure waveform, which when compared to a pre-programmed standard waveform, determines whether the process is in or out of control. Data acquisition can be stored locally or to a LAN. The custom configured fluid waveform analyzers are available in a range of price and performance options to meet your specific dispensing process requirements. LOCTITE SIGNATURE SERIES Designed to monitor a single dispense point, the Loctite Signature Series is ideal for analyzing drop and Rotospray dispense cycles up to 3 seconds. Includes one dry-contact pass/ fail output relay. An optional remote display monitor is available separately. Not capable of internal data storage. LOCTITE SIGNATURE SERIES 4 Designed to monitor to 4 dispense points simultaneously, the Loctite Signature Series 4 is ideal for analyzing bead or drop dispense cycles up to 40 seconds. This ethernet-ready, industrial PC- based system comes standard with a hard drive for data storage. Capable of saving multiple dispense profiles, and can perform SPC analysis on data acquired. Types of Fluids Handled Any fluids ranging from water- thin liquids to thick pastes. Availability Series Detection of: Plugged and broken dispense tips Dispense tip voids No dispense Low pressure under- sized beads High pressure over- sized beads Series 4 Full detection of Series plus: Air bubbles Testing and data acquisition flexibility Mathematical processing Statistical data analysis and reporting using LAN & SQL technology Database archiving and network support Loctite Fluid Waveform Analyzers are available through our Custom Equipment Group in a range of price and performance options, custom configured to meet your specific requirements. For more information, contact the Technical Information Department at LOCTITE ( ). 79

82 CONSUMABLES Consumables Dispense Accessories Dispense Accessories Henkel offers a comprehensive line of Loctite brand dispense tips, static mix nozzles, and syringe barrel components. Our high precision stainless steel, tapered polyethylene and flexible polypropylene tips all feature a positive locking, helical thread design to ensure the tip will stay intact during the toughest applications. A wide variety of static mix nozzles are available to meet your two part adhesive dispensing needs. High quality syringe barrels and components will ensure consistent single component adhesive dispensing needs are met. High Precision Stainless Steel Dispense Tips 4" STAINLESS STEEL TIPS HELICAL THREAD 50 pack Item Number 000 pack Item Number Hub Color Gauge Olive Green Pink Purple Red Clear Lavender Yellow 32 2" STAINLESS STEEL TIPS HELICAL THREAD 50 pack Item Number 000 pack Item Number Hub Color Gauge White Amber Green Pink Purple Blue Orange Red Light Grey 27 2" STAINLESS STEEL TIPS HELICAL THREAD 50 pack Item Number 000 pack Item Number Hub Color Gauge Amber Green Pink Purple Blue Orange Red Lavender BY 2" STAINLESS STEEL TIPS HELICAL THREAD 50 pack Item Number 000 pack Item Number Hub Color Gauge White Amber Green Pink Purple Blue Orange Red Light Grey 27 " STAINLESS STEEL TIPS HELICAL THREAD 50 pack Item Number 000 pack Item Number Hub Color Gauge White Amber Green Pink Purple Blue Orange Red Light Grey BY 2" STAINLESS STEEL TIPS HELICAL THREAD 50 pack Item Number 000 pack Item Number Hub Color Gauge White Amber Green Pink Purple Blue Orange Red Light Grey 27 80

83 Tapered Dispense Tips 4" POLYETHYLENE TAPERED TIPS HELICAL THREAD AND UV LIGHT BLOCK ADDITIVE NEW 50 pack Item Number 000 pack Item Number Hub Color Gauge White Grey Green Pink Blue * 98659* Red * 9866* Clear 27 * New smaller gauge sizes. General Purpose Dispense Tips 2" STAINLESS STEEL TIPS 50 pack Item Number 000 pack Item Number Hub Color Gauge Olive Amber Green Pink Purple Blue Orange Red Clear 27 CONSUMABLES Dispense Accessories Flexible Dispense Tips 2" POLYPROPYLENE TIPS HELICAL THREAD 50 pack Item Number 000 pack Item Number Hub Color Gauge Amber Green Pink Red 25 General Purpose Tapered Dispense Tips 4" POLYETHYLENE TAPERED TIPS 50 pack Item Number 000 pack Item Number Hub Color Gauge Tan Grey Green Pink Blue 22 Additional Dispense Tips and Accessories Cartridge Accessories LOCTITE SHOWCASE NEEDLE VARIETY KIT Item Number: This kit contains 5 each of an assortment of high precision Stainless Steel tips in various lengths and gauges. Tapered and Flexible Dispense Tips are also included. All dispense tips have helical thread Luer- Lok hubs for reliable locking. PRODUCT Item # Description PRODUCT Item Numbers Description / SS, PTFE Lined, 25 Gauge (50/000 pack) Luer-Lok Adapter Kit, 20 Luer-Loks and 5 adapters / Tip caps (50/000 pack) 9726 / High Density Polyethylene, 5 Gauge, White (50/000 pack) 2 each of a variety of Helical Threaded 2" Stainless Steel, Tapered Tip, and Polypropylene tips Formable Dispense Tip, 2 Gauge (00 pack) Tri-Nozzle Helps eliminate bubbles in anaerobic gasket applications Light blocking shield for dispense tips (0 pack) Vari-Drop Applicator Brushes (0 pack) PRODUCT Item # Description Roller Assembly " wide band Roller Assembly 2" wide band Replacement Rollers " wide (3 pack) Replacement Rollers 2" wide (3 pack) " wide x 3 8" NPT Dispense nozzle (0 pack) Cartrige-Syringe Adapter: 4" Semco Thread x Female Luer. Used for downloading Cartridge-Tube Fitting Adapter: ( 4" FNPT x 4" male Semco Thread) Used for connecting tube fittings to cartridges ( or also required and sold separately) (3 pack) Tube Fitting: 4" male NPT x 4" feed tube (0 pack) Tube Fitting: 4" male NPT x 3 8" feed tube (0 pack) Aero Nozzle for Silicones in aerosol cans (0 pack) Cartridge Adapter: SS, ( 4" FNPT x 4" female Fischbach Thread), used for connecting tube fittings Cartridge Dispense Tip: 4" male Semco Thread (0 pack) Cartridge-Needle Adapter: (Female Luer x 4" male Semco Thread) Luer-Lok adapter for dispense needle attachment (5 pk) Cartridge-Needle Adapter: 4" NPT Thread x Female Luer - shown with for 4" Fischbach. For needle attachment ( 5 pack) Cartridge-Syringe Adapter: 4" MNPT x Female Luer. shown with for 4" Fischbach. Used for downloading (5 pack) 8

84 CONSUMABLES Dispense Accessories Loctite Brand Static Mix Nozzles and Accessories PRODUCT Item Numbers Package Quantity 0,000 0, , , ,000 0, ,000 0, ,000 0, , , , ,000 See description Description 50 ml Square Mix Nozzle, Luer/Stepped Combo Tip, 3.25" Overall Length, 5.3 mm 2, 6 elements, :, 2: mix ratios. 50 ml Square Mix Nozzle, Luer/Stepped Combo Tip, 4.5" Overall Length, 5.3 mm 2, 24 elements, :, 2:, 4: mix ratios. 50 ml Mix Nozzle, 5.9" Overall Length, 0.250" ID, Slip-Luer, 20 elements, :, 2: and 4: ratios. 50 ml Mix Nozzle, 5.9" Overall Length, 0.250" ID, Stepped Tip-Luer, 20 elements, :, 2: and 4: ratios. 50 ml Mix Nozzle, Luer Tip, 6.0" Overall Length, 6.0 mm diameter, 2 elements, :, 2:, 4: mix ratios. 50 ml Mix Nozzle, Stepped Tip, 6.0" Overall Length, 6.0 mm diameter, 2 elements, :, 2:, 4: mix ratios. 50 ml Mix Nozzle, Stepped Tip, Keyed, 5.9" Overall Length, 5.4 mm diameter, 28 elements, 0: mix ratio. 50 ml-s Mix Nozzle, Stepped Tip, 6.2" Overall Length, 6.5 mm ID, 20 elements, 0:-S cartridges only 200/400 ml Square Mix Nozzle, Luer/Stepped Combo Tip, 5.0" Overall Length, 5.3 mm 2, 24 elements, :, 2:, 4: mix ratios. 200/400 ml Square Mix Nozzle, Stepped Tip, 5." Overall Length, 7.5 mm 2, 24 elements, :, 2: mix ratios. 200/400 ml Square Mix Nozzle, Threaded Bell End 0.7 mm square, 87 mm Overall Length, 24 elements, :, 2: ratios. 200/400 ml Mix Nozzle, Stepped Tip, 7.3" Overall Length, 6.3 mm diameter, 24 elements, :, 2: mix ratios. 200/400 ml Mix Nozzle, Stepped Tip, 8.8" Overall Length, 8 mm diameter, 24 elements, :, 2: mix ratios. 200/400 ml Mix Nozzle, Stepped Tip, 0.9" Overall Length, 0 mm diameter, 24 elements, :, 2: mix ratios. 200/400 ml Mix Nozzle, 7.4" Overall Length, 0.88" ID, Stepped Tip, 32 Elements, :, 2: and 4: ratios. 200/400 ml Mix Nozzle, 9.0" Overall Length, 0.88" ID, Stepped Tip, 48 Elements, :, 2: and 4: ratios. 200/400 ml Mix Nozzle, Luer Tip, 9.5" Overall Length, 0.25" ID, Slip Luer, 32 Elements, : and 2: ratios. 200/400 ml Mix Nozzle,.44" Overall Length, 8 mm diameter, 32 elements, :, 2: mix ratios. 200/400 ml Mix Nozzle, Stepped Tip, Keyed, 9." Overall Length, 8 mm diameter, 24 elements, :, 2: ratios. 200/400 ml Mix Nozzle, Stepped Tip, Keyed, 0.8" Overall Length, 0 mm diameter, 24 elements, 4:, 0: mix ratios. 200/400 ml Mix Nozzle, Stepped Tip, 4.2" Overall Length, 9.3 mm diameter, 40 elements, :, 2: mix ratios. Luer-Lok Adapter for 6.3 and 8 mm Stepped Tip Mix Nozzles, Allows for Dispense Needle Attachment, (0 pack). Mix Nozzles and Dispense Needles sold separately. Ribbon Tip Adapter, allows Ribbon Tip use with 0 mm. Mix Nozzles 9846, and 98409, sold separately. 200/400 ml Snap Tip Mix Nozzle, 8.9" overall length, 8 mm diameter. 24 elements, :, 2: mix ratios. For use with Ribbon Tips. 200/400 ml Snap Tip Mix Nozzle, 9.3" overall length, 9.3 mm diameter., 24 elements, :, 2: mix ratios. For use with Ribbon Tips. Snap Tip Mix Nozzle and Ribbon Tip Sample Kit. Contains: 6 pieces each of: 2, 25, and 43 mm Ribbon Tips 3 pieces each of: 8 and 9.3 mm diameter Snap Tip Mix Nozzles 2 mm Ribbon Tip. Sold Separately. 25 mm Ribbon Tip. Sold Separately. 43 mm Ribbon Tip. Sold Separately. 82

85 Loctite Brand Syringe Accessories PRODUCT Item Numbers Description 3 ml Syringe Air Line Adapter 5 ml Syringe Air Line Adapter 0 ml Syringe Air Line Adapter 30 ml and 55 ml Syringe Air Line Adapter Contents 2 Air Line Adapters Common to all part numbers (syringe barrel sold separately) CONSUMABLES Dispense Accessories ml Syringe Starter Kit ml Syringe Starter Kit 5 Caps 5 Pistons 4 Clear Barrels Black Barrel 5 Tips Air Line Adapter ml Syringe Starter Kit ml Clear Syringe Barrel Kit ml Clear Syringe Barrel Kit ml Clear Syringe Barrel Kit 20 Barrel Caps, 40 Pistons, 40 Barrels, 40 Barrel Tips 0 Barrel Caps, 20 Pistons, 20 Barrels, 20 Barrel Tips 5 Barrel Caps, 0 Pistons, 0 Barrels, 0 Barrel Tips ml Black Syringe Barrel Kit for UV Adhesives 30 ml Black Syringe Barrel Kit for UV Adhesives 55 ml Black Syringe Barrel Kit for UV Adhesives 20 Barrel Caps, 40 Pistons, 40 Barrels, 40 Barrel Tips 0 Barrel Caps, 20 Pistons, 20 Barrels, 20 Barrel Tips 5 Barrel Caps, 0 Pistons, 0 Barrels, 0 Barrel Tips Various Clear or Black 3, 5, 0, 30, and 55 ml Piston/Syringe Combination Packages See page 85 for syringe and piston options and item numbers. Various Dark Amber Syringe and Piston options Available upon request. Please contact your Loctite Sales Representative or contact us at Air Line Filter for Syringe Dispensing to prevent product back flow Filter Assembly with 2 Hose Crimps Loctite Vertical Syringe Stand for 0 ml and 30 ml syringe barrels (Black) Stand (syringe barrel and air line adapter sold separately) 9850 Loctite Applicator Holder for 0 ml, 30 ml and 55 ml syringe barrels (Red) Holder (syringe barrel and air line adapter sold separately) 83

86 LOCTITE Dispense BRAND DISPENSING SPARE Accessories PARTS AND ACCESSORIES PARENT PRODUCT Accessory Item Numbers Description Package Quantity Loctite Fixmaster Rapid Rubber Repair Dispenser ml mix nozzle, stepped 8 mm end Loctite Hand Pump, 250 ml Loctite Digital Syringe Dispensing System Loctite Digital Syringe Dispensing System Loctite Integrated Semi-Automatic Controller Dispenser 0-00 psi 9700 Loctite Integrated Semi-Automatic Controller Dispenser 0-5 psi 9707 Loctite Integrated Semi-Automatic Controller Disp. with Low Level Sensor 0-00 psi Loctite Integrated Semi-Automatic Controller Disp. with Low Level Sensor 0-5 psi 97 Loctite Hand Held Applicator, Manual 972 Loctite Hand Held Applicator, Pneumatic, Foot 976 Loctite Hand Held Applicator, Pneumatic, Finger Switch 973 Loctite Stationary Applicator Valve with /4" Feed Line 974 Loctite Stationary Applicator Valve with 3/8" Feed Line Loctite Single Channel Automatic Controller Replacement tubing Replacement nozzle Replacement foot switch for Replacement foot switch Applicator holder Universal power cord Replacement rupture disc Tank feed line fitting Replacement reservoir lid o-ring 3/8" feed line conversion kit Luer-Lok adapter kit Replacement finger lever for 97 Replacement actuator for 972 Replacement actuator for 976 Replacement valve assembly, all applicators Replacement shut-off valve assembly for 973 Replacement shut-off valve assembly for 974 Mounting bracket Replacement actuator assembly Air filter and regulator Pneumatic tubing, 4 mm OD, 33 ft. Pneumatic tubing, 6 mm OD Threaded fitting for pneumatic supply and reservoir Threaded fitting dispensing valves and advancing slide 20 Luer-Lok, 5 adapters 9730 Loctite LV Hand Held Applicator Repair Kit for LV hand held valve N/A 9732 Loctite Vari-Drop Applicator, without Tubing Vari-Drop applicator repair kit Vari-Drop applicator brushes Loctite Diaphragm Valve with 4" Feed Line 9736 Loctite Diaphragm Valve with 3 8" Feed Line Loctite Light Cure Dispense Valve 9803 Loctite Cyanoacrylate Dispense Valve 980 Loctite Hysol Reactive Urethane Cartridge Dispenser Loctite 300 ml Cartridge Pusher Various Diaphragm valve actuator replacement Diaphragm valve shut-off 2 mm replacement Diaphragm Valve shut-off 3 mm replacement Diaphragm replacement kit Mounting bracket Valve rebuild kit Valve rebuild kit 9803 Pneumatic foot switch Vertical stand Replacement sleeve kit Fitting: /4" NPT x /4" tube, black plastic Fitting: /4" NPT x 3/8" tube, black plastic See Cartridge Accessories See additional Cartridge Accessories - page Loctite Digital Dispense Controller 9720 Replacement foot switch assembly Loctite Digital Multi-Functional Controller Loctite Shot Miser Valve Controller Advancing slide (2" stroke) Replacement foot switch assembly 2-Hand anti-tie-down switch set Foot pedal with fitting and tubing Solenoid valve, 4 way Loctite Micro Needle Valve 9809 Micro needle valve rod replacement kit N/A Loctite Shot Miser Dispense Valve Loctite Shot Miser Reservoir, Liter Loctite 2.25 Gallon Pressure Reservoir Loctite Posi-Link 5-25 Actuator Loctite Posi-Link 0-50 Actuator Vari-Drop without tubing and guards Vari-Drop repair kit Nut and sleeve sub-assembly Silicone grease, 6 gram tube Toggle valve 3 way Pressure regulator Pressure gauge Reservoir lid o-ring for acetone based primers Anti-bubbler kit Pressure safety relief valve Replacement reservoir lid o-ring Pressure safety relief valve Pressure regulator Pressure gauge Reservoir lid gasket; material: Buna N Reservoir lid gasket; material: EPR Loctite 5-25, 5 ml Barbed Piston Loctite 5-25, 0 ml Barbed Piston Loctite 5-25, 25 ml Barbed Piston Loctite 0-50, 0 ml Barbed Piston Loctite 0-50, 25 ml Barbed Piston 9864 Loctite Posi-Link 0-50, 50 ml Dual Cartridge Nest Cartridge cradle Loctite Posi-Link Actuator 974 Static mixer pinch valve Various 2 84

87 Accessory PARENT PRODUCT Item Numbers Loctite Spray Valve Loctite Benchtop Peristaltic Dispenser Description Spray nozzle kit 0.04 diameter Spray nozzle kit diameter Spray nozzle kit diameter Spray valve seal kit Spray valve hose and fitting kit Spray valve piston repair kit Feed line tubing 2.0 mm OD x.4 mm ID, clear Feed line tubing.6 mm OD x.0 mm ID, clear Feed line tubing.6 mm OD x.0 mm ID, black Feed line tubing 2.0 mm OD x.4 mm ID, black Feed line tubing 3.0 mm OD x.9 mm ID, clear Feed line tubing 3.0 mm OD x 2.4 mm ID, clear Feed line tubing 3.0 mm OD x 2.4 mm ID, black Feed line tubing 2.5 mm OD x.9 mm ID, black Applicator nozzle.2 mm ID Applicator nozzle.4 mm ID Applicator nozzle.9 mm ID Applicator nozzle 2.4 mm ID Applicator assembly Pump head Vari-Drop applicator Vari-Drop applicator repair kit Reservoir lid o-ring 200 g gel tube kit Package Quantity x 65.6' x 65.6' x 65.6' x 65.6' x 65.6' x 65.6' x 65.6' x 65.6' LOCTITE BRAND DISPENSING Dispense SPARE PARTS AND ACCESSORIES Accessories Loctite Bond-A-Matic 3000 Dispenser, 0-5 psi Loctite Bond-A-Matic 3000 Dispenser, 0-00 psi Loctite Bond-A-Matic 3000 Reservoir, 0-5 psi with Low Level Sensor DC Loctite Bond-A-Matic 3000 Reservoir, 0-5 psi with Low Level Sensor AC Loctite Bond-A-Matic 3000 Reservoir, 0-00 psi with Low Level Sensor DC Loctite Bond-A-Matic 3000 Reservoir, 0-00 psi with Low Level Sensor AC Loctite Bond-A-Matic 3000 Reservoir, 0-5 psi, No Applicator Loctite Bond-A-Matic 3000 Reservoir, 0-00 psi, No Applicator Replacement reservoir lid o-ring 200 g gel tube kit Replacement 0 VAC sensor, 98272, only Replacement 24 VDC sensor, , only Loctite 4 Liter Gravity Feed Reservoir Loctite Positive Displacement Pump Loctite Pump-A-Bead II Dispenser Loctite Poppet Valve, Acetal Copolymer Body Loctite Poppet Valve, Acetal Copolymer Body Loctite Dial-A-Seal Applicator Loctite Syringe Barrel and Piston Kits (Dark Amber Syringes are also available in the same packages. Call for special orders.) Syringe Barrel and Piston Syringe Barrel Only Pistons Only Loctite Tubing VDC sensor Replacement reservoir body Replacement actuator assembly Replacement pump assembly Pump replacement Nozzle: 0.025" diameter Nozzle: 0.035" diameter Nozzle: 0.060" diameter Replacement poppet valve Nozzle: 0.025" diameter Nozzle: 0.035" diameter Nozzle: 0.060" diameter Valve rebuild kit Tube adapter Pump rebuild kit Replacement turret Replacement cap liter bottle 3 ml syringe barrel and piston, natural 3 ml syringe barrel and piston, natural 3 ml syringe barrel and piston, black 3 ml syringe barrel and piston, black 5 ml syringe barrel and piston, natural 5 ml syringe barrel and piston, natural 5 ml syringe barrel and piston, black 5 ml syringe barrel and piston, black 0 ml syringe barrel and piston, natural 0 ml syringe barrel and piston, natural 0 ml syringe barrel and piston, black 0 ml syringe barrel and piston, black 30 ml syringe barrel and piston, natural 30 ml syringe barrel and piston, natural 30 ml syringe barrel and piston, black 30 ml syringe barrel and piston, black 55 ml syringe barrel and piston, natural 55 ml syringe barrel and piston, natural 55 ml syringe barrel and piston, black 55 ml syringe barrel and piston, black 3 ml syringe barrel, black 3 ml syringe barrel, natural 5 ml syringe barrel, black 5 ml syringe barrel, natural 0 ml syringe barrel, black 0 ml syringe barrel, natural 30 ml syringe barrel, black 30 ml syringe barrel, natural 55 ml syringe barrel, black 55 ml syringe barrel, natural 3 ml syringe piston 5 ml syringe piston 0 ml syringe piston 30 / 55 ml piston 3 8" black PTFE lined feed tube 4" black PTFE lined feed tube 4" clear polyethylene feed tube 3 8" clear polyethylene feed tube 4" clear nylon feed tube for Pump-A-Bead Silicone tubing for dispense valve purging (0 pack) 50,000 50,000 50,000 50,000 50,000 50, ,000,000,000,000,000, ,000,000,000, feet 33 feet 33 feet 33 feet 33 feet foot 85

88 MOTION CONTROL Motion Control Robot Dispense Systems Robot Dispense Systems Available in both Benchtop and SCARA model types, Loctite brand robots are designed to simplify the dispensing of adhesives and sealants onto complex surface configurations. They allow manufacturers to repeatedly and reliably dispense patterns of liquid material on a programmed basis, resulting in improved process efficiencies, minimal material waste, and reduced manufacturing costs. Robot Types Benchtop robots are beam or gantry style robots designed to be placed on a bench. These robots carry one or more parts that are captured in a fixture that is mounted on the work surface. Motion in the X axis is achieved by moving the work surface forward and backward. The Y and Z axes are achieved by moving the tool head left and right and up and down, respectively, on the beam or gantry. When applicable, the 4th axis (R axis) is achieved by rotating the mounting shaft that protrudes from the tool head. SCARA is an acronym for Selective Compliance Assembly Robot Arm. The robot is a multi- jointed arm that moves above the work surface. It must be mounted near the work surface by the user. The X and Y axes are achieved by changing the angles of the two arms. This creates a kidney shaped dispensing area that is approximately 880 mm (34.6") wide and 440 mm (7.3") tall at the center. The Z axis is achieved by moving both arms up and down. On the 4 axis models, the R axis is achieved by rotating the mounting shaft that protrudes from the end of the arm. For detailed dimension drawings of all benchtop robots, please visit the web at: Just search on the part number you are interested in and scroll down to the product documentation. PRODUCT Loctite 200 Benchtop Robot Station Loctite 300 Benchtop Robot Station Loctite 400 Benchtop Robot Station Loctite 500 Benchtop Robot Station Loctite S440 SCARA-N Robot Station Type Benchtop Benchtop Benchtop Benchtop SCARA Number of controllable axes 3 or 4 3 or 4 3 or 4 3 or 4 3 or 4 X axis 200 mm 300 mm 400 mm 50 mm Arm : 260 mm ± 90 Range of Y axis 200 mm 320 mm 400 mm 50 mm Arm 2: 80 mm ± 50 operation Z axis 50 mm 00 mm 50 mm 50 mm 00 mm R axis ± 360 ± 360 ± 360 ± 360 ± 360 Portable weight limitations Speed Work Surface 7.0 kg.0 kg.0 kg.0 kg N/A Tool Head 3.5 kg 6.0 kg 6.0 kg 6.0 kg 5.0 kg PTP (X, Y) 5 to 700 mm/s 8 to 800 mm/s 8 to 800 mm/s 8 to 800 mm/s 5 to 500 mm/s PTP (Z) 5 to 250 mm/s 3.2 to 320 mm/s 3.2 to 320 mm/s 3.2 to 320 mm/s 3.2 to 320 mm/s PTP (R) 6 to 600 /s 8 to 800 /s 8 to 800 /s 8 to 800 /s 0 to,000 /s CP (X, Y, Z) 0. to 500 mm/s 0. to 800 mm/s 0. to 800 mm/s 0. to 800 mm/s 0. to 800 mm/s 86

89 LOCTITE 200 BENCHTOP ROBOT STATION The Loctite 200 Series Benchtop Robot has a 200 by 200 mm range of operation. Eight different configurations, as shown in the chart, are available to meet your process requirements. This unit is fully compliant with RIA (Robotics Industry Association) safety guidelines. Programming accessories, dispensing equipment, integration cables and mounting hardware are sold separately. Robot Configurations Item Number 98279A 98280A 9828A 98282A 98283A 98284A 98285A 98286A Description 200 x 200 mm, 3 axis, 0 V 200 x 200 mm, 3 axis, 0 V CE Rated 200 x 200 mm, 3 axis, 220 V 200 x 200 mm, 3 axis, 220 V CE Rated 200 x 200 mm, 4 axis, 0 V 200 x 200 mm, 4 axis, 0 V CE Rated 200 x 200 mm, 4 axis, 220 V 200 x 200 mm, 4 axis, 220 V CE Rated MOTION CONTROL Robot Dispense Systems Integrated solution plug and play Low cost operation and ownership Compact size Application specific software Teach point programming 255 program, 30,000 point memory card A wide variety of mounting hardware is available, see page 95. Programming Simple to program using either a multi-line backlit teach pendant with user-friendly prompts or Windows XP software. The program allows for continuous path motion and automatically interpolates any line or arc in all axes. The manual provides step-by-step instructions for programming the robot. No previous experience is required. Programming Accessories The specially designed, easy-to-use Teach Pendant is the preferred device for programming and operating the robot. A laptop computer loaded with the Teach Point Software can also be used as an alternative Teach Pendant LR- C Teach Point Software Integration Accessories Loctite brand cables and junction boxes provide plug and play integration solutions for a variety of Loctite dispensing systems. Single or multiple systems functionality can be easily accommodated Interface Cable Benchtop Robots, 37 pin male D x multi. Use with all Loctite Robot single dispenser integration. Integrates Loctite Precision Syringe Dispenser (97006), Digital Syringe Dispenser (883976), Spray Controller (9852), Integrated Semi-Auto Controllers (97007, 9700, 9707, 97020), Benchtop Peristaltic Dispenser (98548), and Posi-Link Controller (98377) Robot Interface Junction Box. Provides convenient connection point between robots and up to 2 external devices including all Loctite dispensers, UV Wands, LED cure systems, and 3rd party solenoids, grippers, etc. The Junction Box accepts up to 7 inputs and 5 outputs, device status indicator lights with a view window, and a 500 ma/24 VDC power supply for powering 3rd party devices. Connection of the Junction Box to the Benchtop Robot requires one additional cable (sold separately) Junction Box Cable, Benchtop Robots, 37 pin male D x 37 pin male D Attribute Value Number of Controllable Axes 3 to 4 X axis 200 mm Range of Y axis 200 mm Operation Z axis 50 mm R axis ± 360 Portable Weight Work Surface 7.0 kg Tool Head 3.5 kg PTP (X,Y) 5 to 700 mm/s Speed PTP (Z) 2.5 to 250 mm/s PTP (R) 6 to 600 /s CP (X,Y, Z) 5 to 200 mm/s Repeatability X, Y, Z axis ± 0.0 mm Accuracy R axis ± 0.02 CPU 32 bit Control Method Point-to-Point or Continuous Path Drive Method 5-phase stepping motor I/O 6 Program Capacity 255 programs Data Memory Capacity 30,000 points Width, 3 axis 320 mm Width, 4 axis 330 mm Dimensions Depth 388 mm Height, 3 axis 536 mm Height, 4 axis 575 mm Weight 8 kg Power Source 0/220 VAC; 50/60 Hz Consumption Current 200 VA Working Temperature 0 to 40 C Environment Humidity 20 to 95% RH Parts Included () Teach Pendant By-Pass Connector () Robot () External Interlock By-Pass Connector () Power Cord () CD-ROM Manual and LR-C Points Limited Software Additional Information Additional Accessories Sold Separately Extensive Mounting Hardware Option Listing on page 95. See for Detailed Dimension drawings Solenoid Valve Module for pneumatic control by the robot PC Interface Cable Benchtop Robots, 9 pin female D x 9 pin female D 87

90 MOTION CONTROL Robot Dispense Systems LOCTITE 300 BENCHTOP ROBOT STATION The Loctite 300 Series Benchtop Robot has a 300 by 320 mm range of operation. Eight different configurations, as shown in the chart, are available to meet your process requirements. This unit is fully compliant with RIA (Robotics Industry Association) safety guidelines. Programming accessories, dispensing equipment, integration cables and mounting hardware are sold separately. Robot Configurations Item Number 98287A 98288A 98289A 98290A 9829A 98292A 98293A 98294A Description 300 x 320 mm, 3 axis, 0 V 300 x 320 mm, 3 axis, 0 V CE Rated 300 x 320 mm, 3 axis, 220 V 300 x 320 mm, 3 axis, 220 V CE Rated 300 x 320 mm, 4 axis, 0 V 300 x 320 mm, 4 axis, 0 V CE Rated 300 x 320 mm, 4 axis, 220 V 300 x 320 mm, 4 axis, 220 V CE Rated Integrated solution plug and play Low cost operation and ownership Compact size Application specific software Teach point programming 255 program, 30,000 point memory card A wide variety of mounting hardware is available, see page 95. Programming Simple to program using either a multi-line backlit teach pendant with user-friendly prompts or Windows XP software. The program allows for continuous path motion and automatically interpolates any line or arc in all axes. The manual provides step-by-step instructions for programming the robot. No previous experience is required. Programming Accessories The specially designed, easy-to-use Teach Pendant is the preferred device for programming and operating the robot. A laptop computer loaded with the Teach Point Software can also be used as an alternative Teach Pendant LR- C Teach Point Software Integration Accessories Loctite brand cables and junction boxes provide plug and play integration solutions for a variety of Loctite dispensing systems. Single or multiple systems functionality can be easily accommodated Interface Cable Benchtop Robots, 37 pin male D x multi. Use with all Loctite Robot single dispenser integration. Integrates Loctite Precision Syringe Dispenser (97006), Digital Syringe Dispenser (883976), Spray Controller (9852), Integrated Semi-Auto Controllers (97007, 9700, 9707, 97020), Benchtop Peristaltic Dispenser (98548), and Posi-Link Controller (98377) Robot Interface Junction Box. Provides convenient connection point between robots and up to 2 external devices including all Loctite dispensers, UV Wands, LED cure systems, and 3rd party solenoids, grippers, etc. The Junction Box accepts up to 7 inputs and 5 outputs, device status indicator lights with a view window, and a 500 ma/24 VDC power supply for powering 3rd party devices. Connection of the Junction Box to the Benchtop Robot requires one additional cable (sold separately) Junction Box Cable, Benchtop Robots, 37 pin male D x 37 pin male D Attribute Value Number of Controllable Axes 3 to 4 X axis 300 mm Range of Y axis 320 mm Operation Z axis 00 mm R axis ± 360 Portable Weight Work Surface.0 kg Tool Head 6.0 kg PTP (X,Y) 8 to 800 mm/s Speed PTP (Z) 3.2 to 320 mm/s PTP (R) 8 to 800 /s CP (X,Y, Z) 0. to 800 mm/s Repeatability X, Y, Z axis ± 0.0 mm Accuracy R axis ± 0.02 CPU 32 bit Control Method Point-to-Point or Continuous Path Drive Method 5-phase stepping motor I/O 6 Program Capacity 255 programs Data Memory Capacity 30,000 points Width 560 mm Dimensions Depth 529 mm Height, 3 axis 649 mm Height, 4 axis 690 mm Weight 35 kg Power Source 0/220 VAC; 50/60 Hz Consumption Current 200 VA Working Temperature 0 to 40 C Environment Humidity 20 to 95% RH Parts Included () Teach Pendant By-Pass Connector () Robot () External Interlock By-Pass connector () Power Cord () CD-ROM Manual and LR-C Points Limited Software Additional Information Additional Accessories Sold Separately Extensive Mounting Hardware Option Listing on page 95. See for Detailed Dimension drawings Solenoid Valve Module for pneumatic control by the robot PC Interface Cable Benchtop Robots, 9 pin female D x 9 pin female D

91 LOCTITE 400 BENCHTOP ROBOT STATION The Loctite 400 Series Benchtop Robot has a 400 by 400 mm range of operation. Eight different configurations, as shown in the chart, are available to meet your process requirements. This unit is fully compliant with RIA (Robotics Industry Association) safety guidelines. Programming accessories, dispensing equipment, integration cables and mounting hardware are sold separately. MOTION CONTROL Robot Configurations Item Number 98295A 98296A 98297A 98298A 98299A 98300A 9830A 98302A Description 400 x 400 mm, 3 axis, 0 V 400 x 400 mm, 3 axis, 0 V CE Rated 400 x 400 mm, 3 axis, 220 V 400 x 400 mm, 3 axis, 220 V CE Rated 400 x 400 mm, 4 axis, 0 V 400 x 400 mm, 4 axis, 0 V CE Rated 400 x 400 mm, 4 axis, 220 V 400 x 400 mm, 4 axis, 220 V CE Rated Robot Dispense Systems Integrated solution plug and play Low cost operation and ownership Compact size Application specific software Teach point programming 255 program, 30,000 point memory card A wide variety of mounting hardware is available, see page 95. Programming Simple to program using either a multi-line backlit teach pendant with user- friendly prompts or Windows XP software. The program allows for continuous path motion and automatically interpolates any line or arc in all axes. The manual provides step-by-step instructions for programming the robot. No previous experience is required. Programming Accessories The specially designed, easy-to-use Teach Pendant is the preferred device for programming and operating the robot. A laptop computer loaded with the Teach Point Software can also be used as an alternative Teach Pendant LR- C Teach Point Software Integration Accessories Loctite brand cables and junction boxes provide plug and play integration solutions for a variety of Loctite dispensing systems. Single or multiple systems functionality can be easily accommodated Interface Cable Benchtop Robots, 37 pin male D x multi. Use with all Loctite Robot single dispenser integration. Integrates Loctite Precision Syringe Dispenser (97006), Digital Syringe Dispenser (883976), Spray Controller (9852), Integrated Semi-Auto Controllers (97007, 9700, 9707, 97020), Benchtop Peristaltic Dispenser (98548), and Posi-Link Controller (98377) Robot Interface Junction Box. Provides convenient connection point between robots and up to 2 external devices including all Loctite dispensers, UV Wands, LED cure systems, and 3rd party solenoids, grippers, etc. The Junction Box accepts up to 7 inputs and 5 outputs, device status indicator lights with a view window, and a 500 ma/24 VDC power supply for powering 3rd party devices. Connection of the Junction Box to the Benchtop Robot requires one additional cable (sold separately) Junction Box Cable, Benchtop Robots, 37 pin male D x 37 pin male D PC Interface Cable Benchtop Robots, 9 pin female D x 9 pin female D Attribute Value Number of Controllable Axes 3 to 4 X axis 400 mm Range of Y axis 400 mm Operation Z axis 50 mm R axis ± 360 Portable Weight Work Surface.0 kg Tool Head 6.0 kg PTP (X,Y) 8 to 800 mm/s Speed PTP (Z) 3.2 to 320 mm/s PTP (R) 8 to 800 /s CP (X,Y, Z) 0. to 800 mm/s Repeatability X, Y, Z axis ± 0.0 mm Accuracy R axis ± 0.02 CPU 32 bit Control Method Point-to-Point or Continuous Path Drive Method 5-phase stepping motor I/O 6 Program Capacity 255 programs Data Memory Capacity 30,000 points Width 584 mm Dimensions Depth 629 mm Height, 3 axis 799 mm Height, 4 axis 840 mm Weight 42 kg Power Source 0/220 VAC; 50/60 Hz Consumption Current 200 VA Working Temperature 0 to 40 C Environment Humidity 20 to 95% RH Parts Included () Teach Pendant By-Pass Connector () Robot () External Interlock By-Pass Connector () Power Cord () CD-ROM Manual and LR-C Points Limited Software Additional Information Additional Accessories Sold Separately Extensive Mounting Hardware Option Listing on page 95. See for Detailed Dimension drawings Solenoid Valve Module for pneumatic control by the robot 89

92 MOTION CONTROL LOCTITE 500 BENCHTOP ROBOT STATION The Loctite 500 Series Benchtop Robot has a 50 by 50 mm range of operation. Eight different configurations, as shown in the chart, are available to meet your process requirements. This unit is fully compliant with RIA (Robotics Industry Association) safety guidelines. Programming accessories, dispensing equipment, integration cables and mounting hardware are sold separately. Robot Configurations Robot Dispense Systems Item Number Description x 50 mm, 3 axis, 0 V x 50 mm, 3 axis, 0 V CE Rated x 50 mm, 3 axis, 220 V x 50 mm, 3 axis, 220 V CE Rated x 50 mm, 4 axis, 0 V x 50 mm, 4 axis, 0 V CE Rated x 50 mm, 4 axis, 220 V x 50 mm, 4 axis, 220 V CE Rated Integrated solution plug and play Low cost operation and ownership Compact size Application specific software Teach point programming 255 program, 30,000 point memory card A wide variety of mounting hardware is available, see page 95. Programming Simple to program using either a multi-line backlit teach pendant with user-friendly prompts or Windows XP software. The program allows for continuous path motion and automatically interpolates any line or arc in all axes. The manual provides step-by-step instructions for programming the robot. No previous experience is required. Programming Accessories The specially designed, easy-to-use Teach Pendant is the preferred device for programming and operating the robot. A laptop computer loaded with the Teach Point Software can also be used as an alternative Teach Pendant LR- C Teach Point Software Integration Accessories Loctite brand cables and junction boxes provide plug and play integration solutions for a variety of Loctite dispensing systems. Single or multiple systems functionality can be easily accommodated Interface Cable Benchtop Robots, 37 pin male D x multi. Use with all Loctite Robot single dispenser integration. Integrates Loctite Loctite Precision Syringe Dispenser (97006), Digital Syringe Dispenser (883976), Spray Controller (9852), Integrated Semi-Auto Controllers, (97007, 9700, 9707, 97020), Benchtop Peristaltic Dispenser (98548), and Posi-Link Controller (98377) Robot Interface Junction Box. Provides convenient connection point between robots and up to 2 external devices including all Loctite dispensers, UV Wands, LED cure systems, and 3rd party solenoids, grippers, etc. The Junction Box accepts up to 7 inputs and 5 outputs, device status indicator lights with a view window, and a 500 ma/24 VDC power supply for powering 3rd party devices. Connection of the Junction Box to the Benchtop Robot requires one additional cable (sold separately) Junction Box Cable, Benchtop Robots, 37 pin male D x 37 pin male D PC Interface Cable Benchtop Robots, 9 pin female D x 9 pin female D Attribute Value Number of Controllable Axes 3 to 4 X axis 50 mm Range of Y axis 50 mm Operation Z axis 50 mm R axis ± 360 Portable Work Surface.0 kg Weight Tool Head 6.0 kg PTP (X,Y) 8 to 800 mm/s Speed PTP (Z) 3.2 to 320 mm/s PTP (R) 8 to 800 /s CP (X,Y, Z) 0. to 800 mm/s Repeatability X, Y, Z axis ± 0.0 mm Accuracy R axis ± 0.02 CPU 32 bit Control Method Point-to-Point or Continuous Path Drive Method 5-phase stepping motor I/O 6 Program Capacity 255 programs Data Memory Capacity 30,000 points Width 676 mm Dimensions Depth 728 mm Height, 3 axis 799 mm Height, 4 axis 840 mm Weight 42 kg Power Source 0/220 VAC; 50/60 Hz Consumption Current 200 VA Working Temperature 0 to 40 C Environment Humidity 20 to 95% RH Parts Included () Teach Pendant By-Pass Connector () Robot () External Interlock By-Pass Connector () Power Cord () CD-ROM Manual and LR-C Points Limited Software Additional Information Additional Accessories Sold Separately Extensive Mounting Hardware Option Listing on page 95. See for Detailed Dimension drawings Solenoid Valve Module for pneumatic control by the robot 90

93 LOCTITE Heading S440 SERIES SCARA-N ROBOT Epoxy & Urethane Adhesives The Loctite S440 Series SCARA-N Robot provides maximum flexibility for complex dispensing applications. The robot features a multi-jointed arm that moves above the work surface. The robot dispensing area is a kidney shaped area determined by the two arm lengths. Eight different configurations, as shown in the chart, are available to meet your process requirements. Programming accessories, dispensing equipment, cables and mounting hardware are sold separately. Robot Configurations The complete source on Loctite brand adhesives, sealants, lubricants, Item Number Description SCARA-N, 440 mm, 3 axis, 0 V SCARA-N, 440 mm, 3 axis, 0 V CE Rated coatings, dispensing and curing equipment SCARA-N, 440 mm, 3 axis, 220 V available only from SCARA-N, 440 mm, 3 axis, 220 V CE Rated Henkel SCARA-N, 440 mm, 4 axis, 0 V SCARA-N, 440 mm, 4 axis, 0 V CE Rated SCARA-N, 440 mm, 4 axis, 220 V SCARA-N, 440 mm, 4 axis, 220 V CE Rated MOTION CONTROL Robot Dispense Systems Integrated solution plug and play Low cost operation and ownership Compact size Application specific software Teach point programming 25 program, 30,000 point memory card A wide variety of mounting hardware is available, see page 95. Programming Simple to program using either a multi-line backlit teach pendant with user- friendly prompts or Windows XP software. The program allows for continuous path motion and automatically interpolates any line or arc in all axes. The manual provides step-by-step instructions for programming the robot. No previous experience is required. Programming Accessories The operations box is required. The specially designed, easy- touse Teach Pendant is the preferred device for programming and operating the robot. A laptop computer loaded with the Teach Point Software can also be used as an alternative Operations Box 0506 Teach Pendant LR-C Teach Point Software Integration Accessories Loctite brand cables and junction boxes provide plug and play integration solutions for a variety of Loctite dispensing systems. Single or multiple systems functionality can be easily accommodated Interface Cable SCARA Robots, 37 pin male D x multi. Use with all Loctite Robots single dispenser integration. Integrates Loctite Loctite Precision Syringe Dispenser (97006), Digital Syringe Dispenser (883976), Spray Controller (9852), Integrated Semi-Auto Controllers (97007, 9700, 9707, 97020), Benchtop Peristaltic Dispenser (98548), and Posi-Link Controller (98377) Robot Interface Junction Box. Provides convenient connection point between robots and up to 2 external devices including all Loctite dispensers, UV Wands, LED cure systems, and 3rd party solenoids, grippers, etc. The Junction Box accepts up to 7 inputs and 5 outputs, device status indicator lights with a view window, and a 500 ma/24 VDC power supply for powering 3rd party devices. Connection of the Junction Box to the SCARA Robot requires one additional cable (sold separately) Junction Box Cable, SCARA Robots, 37 pin male D x 25 pin female D PC Interface Cable Benchtop Robots, 9 pin female D x 9 pin female D Attribute Value Number of Controllable Axes 3 to 4 X axis 260 mm ± 90 Range of Y axis 80 mm ± 50 Operation Z axis 00 mm R axis ± 360 Portable Weight Tool Head 5.0 kg PTP (X,Y) 5 to,500 mm/s Speed PTP (Z) 3.2 to 320 mm/s PTP (R) to,000 /s CP (X,Y, Z) 0. to 800 mm/s Repeatability X, Y, Z axis ± 0.0 mm Accuracy R axis ± 0.02 CPU 32 bit Control Method Point-to-Point or Continuous Path Drive Method 5-phase stepping motor I/O Safety Program Capacity 255 programs Data Memory Capacity 30,000 points Width 290 mm Dimensions Depth 773 mm Height 840 mm Weight 4 kg Power Source 0/220 VAC; 50/60 Hz Consumption Current 200 VA Working Temperature 0 to 40 C Environment Humidity 20 to 95% RH Parts Included () Power Cord () Robot () I/O-S Short Plug () CD-ROM Manual and LR-C Points Limited Software Additional Information Additional Accessories Sold Separately Extensive Mounting Hardware Option Listing on page 95. See for Detailed Dimension drawings Solenoid Valve Module for pneumatic control by the robot 9

94 MOTION CONTROL Dispense Stations Dispense Stations When a circular dispense pattern or an advancing dispense valve is required, Loctite brand motion control systems offer robust performance at a lower cost than robotic dispense stations. They are simple to set up and operate and their rugged construction makes them well suited for harsh manufacturing environments. In less complex applications, when a circular dispense pattern or an advancing dispense valve is required, Loctite brand motion control systems offer robust performance at a lower cost than robotic dispense stations. PRODUCT Dispense Pattern Loctite Advancing Slide Dispense Station Loctite Single Rotary Dispense Station Loctite Dual Rotary Dispense Station Item Number Dots or Potting Circles, Arcs and/or Dots in a Circular Pattern Circles, Arcs and/or Dots in a Circular Pattern Number of Dispense Points 2 Minimum Dispense Time 0. seconds 0.0 seconds 0.0 seconds Adjustable Valve Angle Yes Yes Yes Slide Stroke 0 to 2" 0 to 2" 0 to 2" Fluid Pressure Regulation 0 to 90 psi 0 to 90 psi 0 to 90 psi Maximum Part Size N/A 8.5" Diameter 4" Diameter at 90 6" Diameter at 45 Maximum Part Height 2" 2" 8" Weight Capacity 2 N/A 30 lbs. 30 lbs. Rotating Speed N/A 0. to 00 RPM 0. to 00 RPM Programming Program Capacity 4 Adjustable Range Analog Timers N/A Multi-line Digital Control Panel with User Friendly Prompts 0 Programs, 20 Events per Program Multi-line Digital Control Panel with User Friendly Prompts 0 Programs, 20 Events per Program Width 2" 4.25" 4." Dimensions Depth 4.75".5625".6" Height 28" 28.7" 23.9" Weight 25 lbs. 26 lbs. 25 lbs. Power Source 0/220 VAC; 50/60 Hz 0/220 VAC; 50/60 Hz 0/220 VAC; 50/60 Hz The maximum part sizes are estimates and can vary depending on the specific part configuration and the size of the dispense syringe, cartridge or valve used. All units have 0 to 2" adjustable stroke. 2 The weight capacity of the rotary station can vary depending on the center of gravity of the part and the program s rotating speed and acceleration. 30 lb. was provided as a general indicator of the motor s capacity. At weights in this range, the equipment should be evaluated to confirm performance. 92

95 MOTION CONTROL LOCTITE ADVANCING SLIDE DISPENSE STATION Item Number: The Loctite Advancing Slide Dispense Station is used for repetitive dot dispensing or potting operations that require motion in the z-axis. It is a fully integrated system that will control any syringe, cartridge or dispense valve; no separate dispense controller is required. The rugged, allmetal construction is designed for tough manufacturing environments. Integrated solution plug and play Compact size Precision timers with accuracy to 0. second Robust slide design Stroke adjustment 0 to 2" Adjustable height, position and angle of dispense point Sturdy work surface with 4 mounting holes for part fixturing Rugged, all- metal enclosure Vacuum suck- back to eliminate drips when syringe dispensing Auto repeat mode cycles unit continuously without foot switch Wide variety of mounting hardware available Installation Overview A mounting bracket must be purchased separately to hold the syringe, cartridge, or valve. The mounting bracket simply slides over the 3 3 4" mounting rail that is attached to the bottom of the slide and is secured using a nylon screw. Once the dispenser is attached, the pneumatic dispense controls are pressed into the clearly labeled connections. The pneumatic dispense control fittings are 4" female NPT fittings and the most commonly required fittings to integrate a syringe, cartridge or valve are supplied. The height, position and angle of the dispense point can easily be adjusted using the stand clamps. The stand clamps are specifically designed to adjust effortlessly yet consistently hold their position during operation. The dispensing process is controlled using five variables that are easy to adjust, set, and monitor. All timers have adjustable ranges that yield good precision over a very wide range. VARIABLE Dispense pressure Delay time before dispense Dispense time Slide down time Auto cycle time Required Separate Purchases RANGE 0 to 90 psi 0. sec to 500 hours 0. sec to 500 hours 0. sec to 500 hours 0. sec to 500 hours Dispense valve, syringe adapter, or cartridge adapter Mounting bracket Dispense needles Fixture to locate part(s) Tubing for connecting valve(s) and air in Attribute Value Dispense Pattern Dots or potting Number of Dispense Points Slide Stroke 0 to 2" Maximum Part Height * 2" Width 2" Dimensions Depth 4.75" Height 28" Weight 25 lbs. Weight Capacity 2* 50 lbs. Vacuum Range to 5 inches Hg Air Input Clean, dry air not to exceed 25 psig and filtered with a maximum of 50 microns Air Output 0 to 00 psi Power Source 0/220 VAC; 50/60 Hz Programming 4 Adjustable Range Analog Timers Parts Included () Advancing Slide Dispense Station () Fitting Kit for Dispenser Connection () Foot Switch () Power Cord () Manual Additional Information For Valve Dispensing, see pages For Syringe Dispensing, see page 83. For Mounting Hardware, see page 95. For Dispensing Tips, see pages * For explanation of notes and 2, please refer to notes below the chart on page 92. Dispense Stations 93

96 MOTION CONTROL Dispense Stations LOCTITE SINGLE ROTARY DISPENSE STATION Item Number: The Loctite Single Rotary Dispense Station is used for repetitive dispensing of circles, arcs and/or dots in a circular pattern that also requires motion in the z-axis. It is a fully integrated system that will control a syringe, cartridge or dispense valve. No separate dispense controller is required. The programming is menu driven using a multi-line, back-lit display. The rugged, all- metal construction is designed for tough manufacturing environments. LOCTITE DUAL ROTARY DISPENSE STATION Item Number: The Loctite Dual Rotary Dispense Station is used for repetitive dispensing of circles, arcs and/or dots in a circular pattern on two simultaneously controlled stations. It is a fully integrated system that will control a syringe, cartridge or dispense valve. No separate dispense controller is required. The programming is menu driven using a multi-line, back-lit display. Installation and integration with a dispense syringe, cartridge or valve is very simple, only requiring a mounting bracket and several pneumatic connections. The rugged, all-metal construction is designed for tough manufacturing environments. Features for Rotary Dispense Stations: Integrated solution plug and play Compact size Easy to program with menu driven prompts Robust slide design Stroke adjustment 0 to 2" Adjustable height, position and angle of dispense point Rugged, all- metal enclosure Vacuum suck-back to eliminate drips when syringe dispensing Auto repeat mode cycles unit continuously without foot switch Wide variety of mounting hardware available Programming Simple to program using a multi- line, back- lit user interface panel with user friendly prompts. It is possible to enter 0 programs consisting of full circles, dots and/or arcs. Each of these dispense patterns is considered an event and there can be twenty events per program. For each event, the user specifies the start and end coordinates in degrees (determined in set up mode), the rotating speed, the delay after the slide advances but before dispensing starts, and the delay after dispensing before retracting the slide. Programs can be initiated using either a foot switch or the start button. When this occurs, a complete program cycle is executed. The table rotates using a stepper motor that allows the location to be specified within 0. degree. Required Separate Purchases Dispense valve, syringe adapter, or cartridge adapter Mounting bracket Dispense needles Fixture to locate part(s) Tubing for connecting valve(s) and air in Loctite Dual Rotary Dispense Station with a 90 set up Loctite Single Rotary Dispense Station Loctite Dual Rotary Dispense Station with a 45 set up Attribute Dispense Pattern Circles, Arcs and/or Dots in a Circular Pattern Number of Dispense Points 2 Rotating Speed 0. to 00 RPM 0. to 00 RPM Slide Stroke 0 to 2" 0 to 2" Maximum Part Height * 2" 8" at 90 Maximum Part Size * 8.5" Diameter 4" Diameter at 90 6" Diameter at 45 Width 4." 4." Dimensions Depth.6".6" Height 28.7" 23.9" Weight 26 lbs. 25 lbs. Weight Capacity 2* 30 lbs. 30 lbs. Air Input Clean, dry air not to exceed 25 psig and filtered with a maximum of 50 microns Air Output 0 to 00 psi 0 to 00 psi Power Source 0/220 VAC; 50/60 Hz Program Capacity 0 0 Programming Multi-Line Digital Control Panel with User Friendly Prompts Parts Included () Rotary Dispense Station () Fitting Kit for Dispenser Connection () Foot Switch () Power Cord () Manual Additional Information For Valve Dispensing, see pages For Syringe Dispensing, see page 83. For Mounting Hardware, see page 95. For Dispensing Tips, see pages * For explanation of notes and 2, please refer to notes below the chart on page

97 Loctite Brand Mounting Hardware, Workbenches, and Guarding Enclosures MOUNTING BRACKET KITS Mounting bracket kits are used to grasp syringe barrels, Loctite Posi-Link syringe and dual cartridge nests, 300 ml cartridges, dispense valves, and LEDs. Mounting rails or adapters are required to mount the brackets on the robot or dispense station. Item # Description ml syringe mounting bracket kit ml cartridge mounting bracket kit and 9803 valve mounting bracket kit and 974 valve mounting bracket kit and poppet valve mounting bracket kit spray and micro needle valve mounting bracket kit TIP LOCATOR BRACKETS* Tip locator brackets position the dispense tip to increase precision and are used to mechanically set the tip height during installation. A mounting bracket and rail, plate or adapter must be purchased separately. Item # Description Tip locator bracket for 30 ml syringes Tip locator bracket for 300 ml cartridges Tip locator bracket for and 9803 valves Tip locator bracket for 973 and 974 valves Tip locator bracket for and poppet valve * These are sized for ", 25 gauge stainless steel needles and must be modified by the user for larger gauge sizes. Z HEIGHT ADJUSTMENT PLATE FOR 3 AXIS BENCHTOP ROBOTS This plate allows you attach the mounting rails above or below the mounting bracket on the robot. MOTION CONTROL Dispense Stations Universal syringe bracket for Posi-Link ml dual cartridge bracket for Posi-Link and LED mounting bracket kit 3, 5 AND 0 ML SYRINGE ADAPTERS These adapters are inserted into the 30 ml syringe mounting bracket kit to adapt it for 3, 5 and 0 ml syringes. The 30 ml syringe mounting bracket (item 9836) must be purchased separately. Item # Description Z height adjustment plate Z height adjustment plate - Posi-Link Nests MOUNTING RAILS FOR 3 AXIS BENCHTOP ROBOTS AND DISPENSE STATIONS A mounting rail is required when using Loctite brand mounting hardware for all 3 axis Benchtop Robots and Dispense Stations. Item # Description Item # Description ml adapter for use with ml adapter for use with ml adapter for use with inch bar with two cap screws inch bar with two cap screws inch bar with two cap screws MOUNTING ADAPTER FOR ALL 4 AXIS ROBOTS A mounting adapter is required when using Loctite brand mounting hardware for all 4 axis robots. The mounting adapter includes a 360 degree rotation kit. Item # Description Mounting adapter for 4 axis robots 360 DEGREE ROTATION KIT This is used to allow for 360 degrees of rotation when using a mounting bracket kit or tip locator. A 360 degree rotation kit is already included with the mounting adapter for 4 axis robots. Item # Description degree rotation kit COMPLETE MOUNTING KITS FOR 3 AXIS SCARA ROBOTS* Complete mounting adapter kits hold the syringe, cartridge or valve, and position the dispense tip 60 mm from the end of the tool arm. Item # Description ml syringe holder ml cartridge holder and 9803 valve holder and 974 valve holder and poppet valve holder * These are sized for 25 gauge needles and must be modified by the user for larger gauge sizes. MOUNTING PLATE FOR 3 AXIS SCARA ROBOTS A mounting plate is required when using Loctite brand mounting hardware for all 3 axis SCARA Robots (except when using a complete mounting kit). Item # Description Mounting plate for SCARA robot WORKBENCHES Strong and sturdy workbenches Accomodate all Loctite brand robots GUARDING SYSTEMS For Plants requiring higher safety levels Light Curtain or Interlocked Sliding Door* on front Sturdy extruded aluminum frame Polycarbonate panels on left, right and rear Operator control panel mounted on front right Direct plug-in to robots * Interlocked door model for Benchtop units only Item # Description Dimensions Series Workbench 36" W x 24" D x 36" H Series Workbench 42" W x 30" D x 36" H /500 Series Workbench 48" W x 36" D x 36" H SCARA Series Workbench 48" W x 48" D x 36" H Series Slide Door 22" W x 24" D x 27" H Series Light Curtain 22" W x 24" D x 27" H Series Slide Door 30" W x 30" D x 30" H Series Light Curtain 30" W x 30" D x 30" H /500 Series Slide Door 32" W x 36" D x 35" H /500 Series Light Curtain 32" W x 36" D x 35" H SCARA Light Curtain 48" W x 48" D x 36" H 95

98 FUME FILTRATION Fume Filtration System System BENCHTOP FUME FILTRATION SYSTEM Item Number: The Benchtop Fume Filtration System is designed to remove dust particulate and fumes emitted by adhesives, sealants, cleaning solvents, and other chemicals. This compact system offers flexible operation in a small space and matches the airflow of many larger systems. It features quiet operation and a bi- colored LED light to indicate blocked filters. This unit can be operated as an open plenum for a working area up to 2" wide or can easily be converted into an arm system for more direct fume capture. The 2" x 24" flexible arm can be positioned to be unobtrusive to the operator, yet provide effective air filtration. It is equipped with a Deep Bed Activated Carbon Fume Filter. HEPA/Carbon Filters are available separately. High airflow rates Runs quietly LED light indicates blocked filter Efficient arm or plenum applications provide flexibility Compact, space- saving footprint UL, CSA, and CE compliant Installation Overview This filtration system filters fumes emitted from adhesives, sealants, cleaning solvents, and other chemicals, as well as dust particulate from other sources. Recommended Spare Parts Filter, Pre-Filter (set of 5) Filter, Deep Bed Carbon Air Inlet Ports Fan Capacity System Capacity Maximum Static Pressure Power Supply Motor Rating Power Consumption Noise Level, Approx. 2" Diameter x 24" Long or 2" Plenum 50 cfm 50 cf 5 inches of water 90/264 VAC; 50/60 Hz 0. HP; 85 watt amp 55 dba Dimensions (W x D x H) 2" x 0.4" x.75" Weight Power Approvals Parts Included Additional Accessories Sold Separately 5.4 lbs. On/off switch with power indicator light UL, CSA, CE () Fume Filtration System () Pleated Pre-Filter () Manual () Deep Bed Activated Carbon Fume Filter () Power Cable HEPA / Carbon Filter Exhaust Arm Arm Adapter Arm Nozzle, 40 mm 96

99 O-Ring Fabrication O-RING FABRICATION Henkel has introduced our new Loctite Precision O-Ring Cut and Splice Tool that turns industrial o-ring cord stock into precise o-rings that are ready for use in a matter of seconds. Digital calipers ensure accurate and repeatable measurement to ensure that you get a correctly sized o-ring every time. Precision O-Ring Kit LOCTITE PRECISION O-RING CUT AND SPLICE TOOL Item Number: 9863 The Loctite Precision O-Ring Cut and Splice Tool is a patent pending, industrial grade tool that provides precise measuring, cutting and bonding of both standard and metric o-ring cord stock. This tool offers a cost effective solution to creating custom o-rings from.05" to 4" (26 mm to 00 mm) in diameter. It incorporates a digital caliper for precise measurement with every o- ring you make. The scale displays either standard or metric dimensions. The cutting fixture is designed to ensure clean, square cuts, while rugged holding clamps provide seamless bonding of the cord stock. Digital caliper provides precise measurement down to 0.0 mm resolution Measurements can be either in inches or mm Convenient conversion chart provides cord stock length vs. required o- ring diameter Gold plated cutting blade ensures clean cuts and longer life Accommodates cord stock up to 4" (7 mm) in diameter Acetal Copolymer holding clamps are rugged and resist any adhesive build-up O-ring cord stock is placed through the cutting blade assembly and securely attached to the first holding clamp on the sliding digital caliper assembly. The caliper is then extended from a zero point away from the cutting face to the precise distance that will equate to the o-ring diameter required. The cutting blade is then manually engaged to cut the exact length of cord. The loose end of cord stock is now attached to the 2nd holding clamp that properly aligns both ends to each other. Loctite 404 Quick Set Instant Adhesive (available as part of kits and also sold separately) is applied and both ends are brought together making a perfect o-ring bond in just a few seconds. Dimensions Weight Power O-Ring Dimensions Parts Included The Starter Kit and Splice Tool are sold separately. 7.25" L x 6.25" W x 4.75" H 2.8 lbs. Digital Scale uses Button Cell SR44,.55 V Maximum Diameter Cord Stock Diameter: 4" (7 mm) O-Ring Diameter Range:.05" to 4.0" Scale Resolution: 0.0 mm () O-Ring Cut and Splice Tool () Manual () Instruction Sheet Additional Accessories Sold Separately Loctite Precision O-Ring Starter Kit Parts Included: ( each) 3' O-Ring Stock, 0.093", 0.25", 0.87" and 0.25" Diameter () Loctite Clean-Up Solvent () 7426 Loctite Water Proofing Solution () 4655 Loctite 404 Quick Set Instant Adhesive Loctite O-Ring Replacement Cord Stock (All Buna-N, 5 ft. length) " diameter " diameter " diameter " diameter 97

100 LIGHT CURE Light Cure Solutions Solutions Henkel offers the widest selection of light curing equipment available from any one company on the market today. Our Loctite brand insures you have the most innovative and dependable systems for all your light curing adhesive applications. Whether your process calls for a manual, semi- automatic or fully integrated automatic solution, you will find the Loctite brand light curing device to meet your specific requirements. Please see the charts below which summarize our complete line. PRODUCT Item Number Lamp Type LED CURING DEVICES High powered benchtop and portable systems for visible light cure adhesives, providing effective spot curing solutions for both manual or integrated automatic systems. Loctite 7700 LED Light Source 9859 Loctite 7700-HD LED Light Source 9860 LED nm Loctite 7703 LED Light Source Loctite 7703-HD LED Light Source LED - Proprietary Wavelength NEW Loctite CureJet 405 LED LED nm NEW Loctite CureJet Indigo LED LED - Proprietary Wavelength NEW Loctite LED Controller WAND SYSTEMS Four different spot curing systems. one visible light and three UV, each with its own range of curing intensity from to 20 W/cm 2. These systems are ideal for both manual or integrated automatic systems. Loctite Indigo 7720 Visible Light Wand System watt Metal Halide Loctite ZETA 7735 UV Wand System Loctite ZETA 7740 UV Wand System Loctite ZETA 7760 UV Wand System 9837A (Bulb Life Monitoring) 9857A (Bulb Life Monitoring) (Bulb Life Monitoring) 50 watt High Pressure Mercury Arc 00 watt High Pressure Mercury Arc 200 watt High Pressure Mercury Arc 98

101 LIGHT CURE Solutions PRODUCT Item Number Lamp Type PRODUCT Item Number Lamp Type ENCLOSED CHAMBER AND FLOOD SYSTEMS These systems are ideal for batch processing. UV and alternate visible light bulb options are available. CURE CONVEYORS Can be used for either continuous or batch processing of assemblies. NEW Loctite UVALOC 000 UV Cure Chamber watt Mercury Vapor Loctite ZETA 745 UV Benchtop Conveyor W/in. Electrodeless (Sold Separately) Loctite ZETA 760 UV Benchtop Conveyor 98588,800 watt Medium Pressure Mercury Arc Lamp Loctite ZETA 740 UV Chamber watt Metal Halide LIGHT SOURCES Can be used with our Loctite ZETA UV conveyors or integrated into a custom system with added shielding, cooling and venting (not included with these products). Loctite ZETA 74-S UV Flood System watt Metal Halide Loctite Electrodeless Lamp Assembly and Power Supply Loctite High Intensity Ultraviolet Sources (208 VAC) 300 W/in. Electrodeless (240 VAC) 98060,500 watt Medium Pressure Mercury Arc Lamp Loctite Indigo 748 Visible Flood System Loctite ZETA 7420 Visible Light Flood System (0 V) 9882 (220 V) 400 watt Visible Arc Lamp 500 watt Visible Arc Lamp PRODUCT Item Number Measurement Range LIGHT METERS UV and visible light cure systems. These meters provide precise and repeatable measurement of any Loctite brand light cure system to ensure your process remains in control. Loctite ZETA 70-A Dosimeter- Radiometer Loctite ZETA 70-V Dosimeter- Radiometer to 400 nm 350 to 500 nm For proper eye protection, use Loctite brand ultraviolet safety glasses. Loctite ZETA 702 Spot Radiometer to 400 nm / 3 and 5 mm wands Item 9720 Item

102 LED Light Sources LIGHT CURE LED Light Sources Henkel has introduced these new innovative and effective LED light curing devices. High power, portability, continuous duty cycles and long LED life are some of the key reasons that make Loctite brand LED light sources the optimal solution for many light curing adhesive applications. LOCTITE 7700 LED LIGHT SOURCE Item Number: 9859 LOCTITE 7703 LED LIGHT SOURCE Item Number: Light to medium duty use cycles: <50% on time. Light to medium duty use cycles: <50% on time. These high powered, fully portable, hand held light sources are capable of curing a variety of UV/visible adhesives in a matter of seconds. With the focused nature of this system s spectral output, IR output is negligible and part assembly heating is virtually eliminated. Lightweight and compact in size, these units provide extensive use flexibility for even the most crowded or hard- to- reach locations. Instant On/Off no warm up like traditional UV systems LED life lasts up to 5 times longer than typical UV bulb units Pinpoint tip allows close exposures even in the tightest locations Tested Loctite Brand Light Cure Adhesives Cured Tack Free: Item Number: 9859 Item Number: (33 ) All Loctite Loctite (332 ) Flashcure and 3553 Indigo 307 (334 ) Light Cure Visible Light Cure Adhesives 3525 Adhesives OPERATIONAL OPTIONS 9859 and operate on batteries or while plugged into AC power source. Optional timer or foot switch are also available Timer Foot Switch Item Number 9859 Loctite 7700 LED Light Source Loctite 7703 LED Light Source Dimensions 9" L x." W x 0.8" H Weight 0.5 lbs. Utilities Batteries or Universal V; Hz Light Source High Powered LED Typical Cure Area Up to 4" x 4" Typical Output* 0.5 to.0 W/cm to 3.5 W/cm 2 Spectral Output Range 385 to 425; Primary Peak 405 nm* Proprietary Additional Accessories Sold Separately Loctite ZETA 70-V Dosimeter * Exact output measurement is dependent on the brand and calibration method of the meter used. These measurements were made with a Loctite ZETA 70-V Dosimeter-Radiometer at a distance of 0.25" Loctite Safety Glasses (Removes all wavelengths 200 to 540 nm) Loctite LED Holder Replacement Battery Kit AC Battery Charger Loctite ZETA Dosimeter Adapter LED Protective Tip Covers (5 pack) XXX 00

103 LOCTITE 7700-HD LED LIGHT SOURCE Item Number: 9860 Heavy continuous duty cycles: Up to 00% on time. LOCTITE 7703-HD LED LIGHT SOURCE Item Number: Heavy continuous duty cycles: Up to 00% on time. LIGHT CURE LED Light Sources These heavy duty point light source LED models provide the same intensity and curing characteristics as the battery powered 9859 and units, but offer 00% on- time duty cycle capability. Ideal for process line integrations, these units also have alternate operational choices for cycle initiation to meet various processing requirements. Instant On/Off no warm up like traditional UV systems LED life lasts up to 5 times longer than typical UV bulb units Pinpoint tip allows close exposures even in the tightest locations Tested Loctite Brand Light Cure Adhesives Cured Tack Free: Item Number: 9860 Item Number: (33 ) All Loctite Loctite (332 ) Flashcure and 3553 Indigo 307 (334 ) Light Cure Adhesives Visible Light 3525 Cure Adhesives OPERATIONAL OPTIONS 9860 and require the choice of a foot switch, PLC cable, LED timer or pistol grip timer option in order to operate Foot Switch PLC Cable LED Timer Pistol Grip and Timer Additional Accessories Sold Separately Item Number 9860 Loctite 7700-HD LED Light Source Loctite 7703-HD LED Light Source Dimensions 8.9" L x.4" W x 2.0" H Weight 0.75 lbs. Utilities Universal V; Hz Light Source High Powered LED Typical Cure Area Up to 4" x 4" Typical Output* 0.5 to.0 W/cm to 3.5 W/cm 2 Spectral Output Range 385 to 425; Primary Peak 405 nm* Proprietary Loctite ZETA 70-V Dosimeter AC Charger for LED-HD Loctite Safety Glasses (Removes all wavelengths 200 to 540 nm) Loctite ZETA Dosimeter Adapter LED Protective Tip Covers (5 pack) LED-HD Pistol Grip Battery Kit (Kit Includes Replacement Battery, Cap and Charger) * Exact output measurement is dependent on the brand and calibration method of the meter used. These measurements were made with a Loctite ZETA 70-V Dosimeter-Radiometer at a distance of 0.25". 0

104 LED Light Sources LIGHT CURE LOCTITE CUREJET LED LIGHT SOURCES LOCTITE CUREJET 405 LED Item Number: LOCTITE CUREJET INDIGO LED Item Number: Our new Loctite CureJet LEDs are our highest power LED spot curing systems. This innovative design offers significantly wider cure area and curing intensity capability than our single point LED devices, providing the ultimate in processing speeds. Choose the system based on the adhesive systems that are in use. 00% on time duty cycle Highly focused LED with peak intensity at 0.25" from cure surface Instant on/off no warm up like traditional UV systems Manual or timed light exposures using an integrated control timer LED life lasts up to 5 times longer than typical UV bulb units Internal diagnostics and digital I/O port, connect via optional PLC interface cable Stackable with " center to center spacing NEW Loctite CureJet shown with LED Controller and cable sold separately Comparitive Cure Area versus Distance from Cure Surface Cure Area [cm 2 ] Distance [inches] CureJet 7700-HD Loctite CureJet 405 LED Comparative Irradiance versus Distance from Cure Surface Loctite CureJet Indigo LED Comparative Irradiance versus Distance from Cure Surface Irradiance [W/cm 2 ] Irradiance [W/cm 2 ] Distance [inches] CureJet HD Distance [inches] CureJet Indigo Indigo 7703-HD Tested Loctite Brand Light Cure Adhesives Cured Tack Free: 305 (33 ) All Loctite Loctite (332 ) Flashcure and 3553 Indigo 307 (334 ) Light Cure Adhesives Visible Light 3525 Cure Adhesives Item Number Loctite CureJet 405 LED Loctite CureJet Indigo LED Loctite LED Controller Dimensions " W x 2.5" H x 0.25" L " W x 2.5" H x 0.25" L 0" W x 4" H x 9.75" D Weight lbs. lbs. 8 lbs. Input Power 85/264 VAC; 50/60 Hz Maximum Current Typical Intensity*. W/cm W/cm 2 Cure Diameter at 0.25" Distance (Peak Intensity) 0.38" 0.38" Spectral Peak 405 nm Proprietary Additional Items Sold Separately REQUIRED ITEMS SOLD SEPARATELY Loctite LED Controller Loctite ZETA 70-V Dosimeter [Requires Adapter] Loctite CureJet LED Dosimeter Adapter m Interconnecting Cable m Interconnecting Cable Loctite Safety Glasses (Removes all wavelengths 200 to 540 nm) [Recommended] PLC Interface Cable * As measured with a Loctite 70-V at a distance of 0.25". 02

105 Wand Systems Loctite ZETA light cure wand systems are used for the continuous or batch processing of assemblies that require curing in small areas. These cost effective systems provide a variety of curing attributes. Selection of a Loctite ZETA wand system is based on the required lamp intensity and the number and length of the light guides needed as well as the need for continuous intensity monitoring or measuring. The time required to complete the curing process depends primarily on the offset distance from the end of the light guide to the surface of the adhesive, and the type of adhesive being used. LIGHT CURE Wand Systems PRODUCT Loctite Indigo 7720 Visible Light Wand System Loctite ZETA 7735 UV Wand Systems Loctite ZETA 7740 UV Wand Systems Loctite ZETA 7760 UV Wand Systems Item Number A / A / / Useful Curing Diameter 4" to " 4" to " 4" to " 4" to " Light Guides Specific guides are required for each wand. See individual wand descriptions on pages Lamp Type 00 watt Metal Halide 50 watt High Pressure Mercury Arc 00 watt High Pressure Mercury Arc 200 watt High Pressure Mercury Arc Typical Intensity*.0 to.5 W/cm 2 5 to 7 W/cm 2 9 to W/cm 2 6 to 20 W/cm 2 Optimized Spectral Output Range Visible UVA, B, C UVA, B, C UVA, B, C Spectral Wavelength 250 to 40 nm 250 to 40 nm 250 to 40 nm Replacement Bulb (Item Number / Type) Lamp / Reflector Module, 00 W Metal Halide Lamp / Reflector Module, 50 W (HPMA) Additional Accessories Sold Separately Lamp / Reflector Module, 00 W (HPMA) 9845 Lamp / Reflector Module, 200 W (HPMA) LOCTITE LIGHT INTENSITY MONITOR Item Number: Digital light lntensity monitoring option for Loctite UV Wands 95826, and only. LOCTITE ZETA 702 SPOT RADIOMETER Item Number: Effective monitoring of UV wand curing system performance. See page 4. * Exact output measurement is dependent on the brand and calibration method of the meter used. Spectral Output of Loctite ZETA Watt High Pressure Mercury Arc Lamp Spectral Output of Loctite ZETA Watt High Pressure Mercury Arc Lamp Relative Irradiance Wavelength in nm Relative Irradiance Wavelength in nm Relative Output % Spectral Output of Loctite ZETA 7760 Mercury Arc Bulb Spectral Output of Loctite ZETA 7760 Mercury Arc Bulb with Optional Filter Kit to Optimize Tack-Free Surface Cure Relative Output % Wavelength in nm Wavelength in nm 03

106 Wand Systems LIGHT CURE LOCTITE INDIGO 7720 VISIBLE LIGHT WAND SYSTEM Item Number: The Loctite Indigo 7720 Visible Light Wand Curing System provides effective curing for larger bead sizes of our new Loctite Indigo visible light curing adhesives. This curing system utilizes a 00 watt, fully visible metal halide lamp system and provides up to.5 W/cm 2 of visible light curing intensity. The system is designed to be constantly powered, providing for effective continuous duty service. This light source uses a long life fiber optic light guide that significantly outlasts liquid- filled light guides. The light guide is required and sold separately. Output exceeds W/cm 2 for up to 3 4" diameter cure areas Long life fiber optic light guide significantly outlasts liquid- filled light guides Light guide is highly flexible and enhances ability to reach tough location cure areas Contains a 00 watt, visible arc bulb that provides up to 2 times longer life than typical UV bulbs Emits light only in the visible light range Constant- on functionality ensures effective, continuous duty service When the unit is switched on, electrical power is immediately supplied to the lamp. It takes 3 to 5 minutes for the metal halide lamp to come up to full power. A fiber optic light guide, sold separately, is also required and inserted into the lamp iris opening. The light guide focuses the lamp intensity down to a specific diameter and provides the operator convenient and effective control of curing visible adhesive joints up to " diameter. The lamp system is designed to stay continuously on so there is no need for further on/off activation. INTENSITY VS. CURE AREA Distance Typical Cure Diameter Typical Intensity* 0.25" 0.56".6 W/cm 2 0.5" 0.75". W/cm 2 * Exact output measurement is dependent on the brand and calibration method of the UV meter, and the condition and straightness of the light guide used. Dimensions Weight Warm-Up Time Power Supply Main Fuse Replacement Parts Parts Included 4.6" H x 7.25" W x 9.5" D 2 lbs. 3 to 5 minutes 5 VAC; 50/60 Hz 5 A, 250 V watt Metal Halide Bulb () Indigo 7720 UV Wand System () Line Cord () 00 W Metal Halide Bulb () Manual Additional Accessories Sold Separately Loctite Safety Glasses (Removes all wavelengths 200 to 540 nm) mm D x 000 mm Fiber Optic Light Guide Loctite Fiber Optic Light Guide Radiometer Adapter 04

107 LOCTITE ZETA 7735 UV WAND SYSTEMS Item Numbers: 9837A and The Loctite ZETA 7735 UV Wand Systems utilize a 50 watt mercury arc lamp with a universal power supply. The state-of-the-art lamp with elliptical reflector and custom coating delivers unequaled spectral and optical performance in the 50 watt category. These wand systems bridge the gap between low intensity and high intensity spot curing products. They are ideally suited for the medium to low intensity requirements of the photo- optics and audiology industries. Other common uses are fillet curing, wire tacking, and shallow potting. The system can be operated manually or in the timed mode and is capable of interfacing with a PLC. Continuous lamp intensity monitoring is also available by selecting item and the required Light Intensity Monitor item The light guides are also sold separately from the base units. Light guide choices are highlighted below. 5 to 7 W/cm 2 UV output 50 watt high pressure mercury arc lamp 2,000 hours of expected UV lamp life with proper handling and maintenance Manual or timed shutter light exposure, 0 to 99.9 seconds Hour meter for monitoring accumulated lamp life Selector switch for either 0 or 230 VAC Additional Features for Item when used in conjunction with LED control display highlights relative intensity changes in 0% increments Minimum required intensity can be programmed for a warning or integrated to PLC for external alarm or shutdown condition LIGHT CURE Wand Systems When the unit is switched on, the proper electrical power is immediately supplied to the lamp. It will take approximately five minutes for the lamp to reach full power. Once the lamp has reached full power, the unit is ready to cure adhesive. The operator will present the part under the end of the UV light guide. Curing will take place when the UV light is directed at the liquid adhesive. Engaging the foot switch opens the shutter and UV energy produced by the lamp is immediately transmitted through the flexible light guide. The end of the wand can be manually operated or mounted in a fixed position. Light Guides Sold Separately Descriptions : Single end 5 mm diameter x,000 mm long Light Guide : Dual end 3 mm diameter x,000 mm long Light Guide (initial purchase requires Balancing Adapter) 9568: Single end 5 mm diameter x,500 mm long Light Guide Typical Light Guide Cure Areas : 4" to 2" diameter : 8" to 4" diameter 9568: 4" to 2" diameter LOCTITE LIGHT INTENSITY MONITOR Item Number: Power Supply Main Fuse Dimensions Weight Parts Included 90/265 VAC; 50/60 Hz input A, 250 V 5.5" H x 6." W x 6.8" D lbs. () Intensity Monitor () Sensor Input Cable () Power Cord () Manual Item Numbers 9837A / Power Supply 00/240 VAC; 50/60 Hz input Power Protection 5 A / 250 V fuse Auxiliary Control Voltage 2 VDC Entry Fuse 3 A, 250 V Dimensions 7.3" H x." W x 2.8" D Weight 9.5 lbs. Optimized Spectral Output Range UVA, B, C Replacement Bulb (Item Number and Type) UV Output Characteristics Parts Included Replacement Parts Typical UV Spectral Range Primary Peak Lamp/Reflector Module 50 watt HPMA UV Bulb 5 to 7 W/cm 2 (using 5 mm x,000 mm light guide)* 250 to 40 nm 365 nm () Loctite ZETA 7735 UV Wand System () Ultraviolet Protection Glasses () Line Cord () UV Lamp () Foot Pedal () Manual watt HPMA UV Bulb Additional Accessories Sold Separately Loctite ZETA 702 Spot Radiometer (See page 4) Loctite Light Intensity Monitor for only * Exact output measurement is dependent on the brand and calibration method of the UV meter, and the condition and straightness of the light guide used. 05

108 Wand Systems LIGHT CURE LOCTITE ZETA 7740 UV WAND SYSTEMS Item Numbers: 9857A and The Loctite ZETA 7740 UV Wand Systems utilize a 00 watt high-pressure mercury arc lamp with a universal power supply and a liquid-filled light wand. They can be operated manually or in the timed mode and are capable of interfacing with a PLC controlled circuit. Continuous lamp intensity monitoring is also available by selecting item and the required Light Intensity Monitor item The light guides are also sold separately from the base units. Light guide choices are highlighted below. Highest output light intensity; 9 to W/cm 2 Contains a high-pressure mercury arc lamp 2,000 hours of expected UV lamp life with proper handling and maintenance Manual or timed shutter light exposure, 0 to 99.9 seconds Hour meter for monitoring accumulated lamp life Self- test diagnostics display message when a problem exists Additional Features for Item when used in conjunction with LED control display highlights relative intensity changes in 0% increments Minimum required intensity can be programmed for a warning or integrated to PLC for external alarm or shutdown condition When the unit is switched on, the proper electrical power is immediately supplied to the lamp. It will take a few minutes for the lamp to reach full power. The operator will manually or automatically place the part under the end of the UV wand. Curing will take place when the UV light is directed at the liquid adhesive. Engaging the foot switch opens the shutter and UV energy produced by the lamp is immediately transmitted through the flexible light guide. The end of the wand can be manually operated or mounted in a fixed position. Light Guides Sold Separately Descriptions : Single end 5 mm diameter x,000 mm long Light Guide : Dual end 3 mm diameter x,000 mm long Light Guide (initial purchase requires Balancing Adapter) 9568: Single end 5 mm diameter x,500 mm long Light Guide Typical Light Guide Cure Areas : 4" to 2" diameter : 8" to 4" diameter 9568: 4" to 2" diameter LOCTITE LIGHT INTENSITY MONITOR Item Number: Power Supply Main Fuse Dimensions Weight Parts Included 90/265 VAC; 50/60 Hz input A, 250 V 5.5" H x 6." W x 6.8" D lbs. () Intensity Monitor () Sensor Input Cable () Power Cord () Manual Item Numbers 9857A / Power Supply 00/240 VAC; 50/60 Hz input Power Protection 4 A / 250 V fuse Auxiliary Control Voltage 2 VDC Lamp Life Approximately 2,000 hours Warm-Up Time 5 minutes Main Fuse 5 A, 250 V Dimensions 7.3" H x." W x 2.8" D Weight 9.5 lbs. Optimized Spectral Output Range UVA, B, C UV Output Characteristics Parts Included Replacement Parts Typical 9 to W/cm 2 (using 5 mm x,000 mm light guide)* UV Spectral Range 250 to 40 nm Primary Peak 365 nm () Loctite ZETA 7740 UV Wand System () Ultraviolet Protection Glasses () Line Cord () UV Lamp () Foot Pedal () Manual watt HPMA UV Bulb Additional Accessories Sold Separately Loctite ZETA 702 Spot Radiometer (See page 4) Loctite Light Intensity Monitor for only * Exact output measurement is dependent on the brand and calibration method of the UV meter, and the condition and straightness of the light guide used. 06

109 LOCTITE ZETA 7760 UV WAND SYSTEMS Item Numbers: and The Loctite ZETA 7760 UV Wand Systems utilize a 200 watt high pressure mercury arc lamp with a universal power supply and a liquid-filled light wand. These systems have the highest intensity output for a Loctite brand wand system by a factor of 2. The Loctite ZETA 7760 UV Wand Systems can be operated manually or in the timed mode and are capable of interfacing with a PLC controlled circuit. Continuous lamp intensity monitoring is also available by selecting item and the required Light Intensity Monitor item The light guides are also sold separately from the base units. Light guide choices are highlighted below. Our highest output light intensity wand. Typical initial Intensity is 6 to 20 W/cm 2 Contains a high pressure mercury arc lamp,000 hours of expected UV lamp life with proper handling and maintenance Manual or timed shutter light exposure, 0 to 99.9 seconds Hour meter for monitoring accumulated lamp life Self- test diagnostics displays message when a problem exists Additional Features for Item when used in conjunction with LED control display highlights relative intensity changes in 0% increments Minimum required intensity can be programmed for a warning or integrated to PLC for external alarm or shutdown condition When the unit is switched on, the proper electrical power is immediately supplied to the lamp. It will take a few minutes for the lamp to reach full power. The operator will manually or automatically place the part under the end of the UV wand. Curing will take place when the UV light is directed at the liquid adhesive. Engaging the foot switch opens the shutter and UV energy produced by the lamp is immediately transmitted through the flexible light guide. The end of the wand can be manually operated or mounted in a fixed position. Light Guide Options UV wands Description Dimensions Item Numbers Single Pole 2 Pole 3 Pole 4 Pole Standard 5 mm x 000 mm mm x 000 mm N/A mm x 500 mm 9568 Enhanced UVC 2 5 mm x 000 mm mm x 000 mm N/A mm x 500 mm Enhanced UVC wands require optional filter kit (98598) to optimize tack-free surface cure on the Loctite ZETA (sold separately) 2 Requires balancing adapter (95639) on initial setup. Multi-pole guides are only available with 3 mm diameter poles. Item Numbers / Power Supply 90/265 VAC; 50/60 Hz input Power Protection 4 A / 250 V fuse Auxiliary Control Voltage 24 VDC Lamp Life Approximately,000 hours Warm-Up Time 5 minutes Main Fuse 5 A, 250 V Dimensions 8.3" H x.5" W x 3.4" D Weight 9.5 lbs. Optimized Spectral Output Range UVA, B, C 6 to 20 W/cm Typical (using 5 mm x,000 mm light guide)* UV Output Characteristics UV Spectral Range 250 to 40 nm Primary Peak 365 nm Parts Included () Loctite ZETA 7760 UV Wand System () Ultraviolet Protection Glasses () Power Cord () UV Lamp () Foot Pedal () Manual Replacement Parts watt HPMA UV Bulb Additional Accessories Sold Separately Loctite ZETA 702 Spot Radiometer (See page 4) Loctite Light Intensity Monitor for only * Exact output measurement is dependent on the brand and calibration method of the UV meter, and the condition and straightness of the light guide used. LIGHT CURE Wand Systems LOCTITE LIGHT INTENSITY MONITOR Item Number: Power Supply Main Fuse Dimensions Weight Parts Included 90/265 VAC; 50/60 Hz input A, 250 V 5.5" H x 6." W x 6.8" D lbs. () Intensity Monitor () Sensor Input Cable () Power Cord () Manual 07

110 LIGHT CURE Cure Chambers & Flood Systems Cure Chambers & Flood Systems Loctite brand chamber and flood systems are modular low and medium intensity ultraviolet and high intensity visible light emitting units designed for the batch curing of light curing adhesives and coatings. Selection of a Loctite brand chamber and flood system is based on the required intensity of light and cure area. CURE CHAMBERS LOCTITE UVALOC 000 UV CURE CHAMBER Item Number: The Loctite UVALOC 000 UV Cure Chamber, item 80574, is a highperformance modular curing system consisting of a cure chamber, lamp housing, and controller. The chamber has four rack levels to accommodate a slide- in tray that allows for easy positioning of parts of various heights and level of optimum exposure. The lamp is shielded by a timed control shutter that eliminates UV exposure to operators during loading or unloading of parts. A door safety switch prevents opening while exposure is in progress. Typical UV irradiance is up to 0 mw/cm 2, depending upon selection of 4- position rack height Dual power setting of 500 or 000 watts permits curing of temperature- sensitive parts without damage by heat Lamp intensity is continually monitored Low-level output condition can be established to insure optimal curing performance and notification for lamp replacement Effective cure area of 6.3 inches wide by 6.3 inches deep (60 mm x 60 mm). Digital timer allows for setting exposure time from 3 seconds to 5 minutes in one- second increments Pneumatically-operated shutter prevents UV exposure to operators Input Voltage 240 VAC; 50/60 Hz Safety door interlock switch prevents opening of the door while the shutter is open Standard lamp included is mercury vapor lamp; 365 nm wavelength Pneumatic Supply Required Pneumatic Supply Tubing Power Consumption 60 to 90 psi 6 mm,200 watts Optional iron doped or gallium doped lamps available Dimensions Exterior of Unit Cure Chamber 2.0" W x 29 4" H x 7.0" D 9.0" W x 2" H x 3 3 4" D Cure Area 6.3" W x 6.3" D The operator places the part inside the chamber and sets the exposure time. This cure time is controlled by the built-in timer and can be operated in a continuous or timed mode. The operator then triggers the exposure cycle by a foot switch, panel- mount start button, or PLC interface. Upon completion of timer, the operator removes the part from the chamber. NEW Parts Included Replacement Bulb () Cure Chamber, Lamp Housing, and Controller () UV Intensity Sensor and Built-In Digital Intensity Display () Connecting Cable (from controller to lamp housing) () AC Power Cord with pig-tale wire ends () Foot Switch ,000 W Mercury Vapor Additional Accessories Sold Separately Loctite ZETA 70-A Dosimeter-Radiometer (See page 3) Safety Glasses (protects from 200 to 540 nm wavelengths) Iron Doped Lamp Gallium Doped Lamp 08

111 LOCTITE ZETA 740 UV CHAMBER Item Number: The Loctite ZETA 740 UV Chamber provides a reliable and economical design for UV curing and is well suited for most production operations. Excellent for use in confined bond line applications, this medium intensity light source can be used for adhesive applications where high intensity output is not necessary. Contains a 4", 400 watt metal halide bulb Designed to emit in the UVA region Curing area of 8" x 8", and a maximum part height of 4" Operator s hands have no direct exposure to UV energy,000 hours of expected UV bulb life with proper handling and maintenance Convenient pull- out drawer to process parts Viewing window to observe assemblies in process The work surface is covered by a special silicone rubber pad to resist UV deterioration and chemical attack The unit is operated by simply placing the assembly into the cure drawer, closing the drawer, and allowing exposure for the desired time. A viewing window allows monitoring of the curing process. Output Spectral Output of a UV Metal Halide Bulb Wavelength in nm Utilities Lamp Type, (Visible and UV enhanced) Dimensions Weight 20 VAC; 8 amps; 60 Hz 400 watt Metal Halide.5" H x 0.75" W x 20." D 39 lbs. Parts Included () ZETA 740 UV Chamber () Pair Cotton Gloves () UV Protective Eyewear () Power Cord () Manual UV Lamp watt Replacement Parts Loctite Silicone Work Surface Additional Accessories Sold Separately Loctite ZETA 70-A Dosimeter-Radiometer (See page 3) Loctite Visible Light Enhanced Metal Halide Bulb LIGHT CURE Cure Chambers & Flood Systems FLOOD SYSTEMS Shown with Optional Shutter Assembly PRODUCT Loctite ZETA 74-S UV Flood System Loctite Indigo 748 Visible Light Flood System Loctite ZETA 7420 Visible Light Flood System Item Number / 9882* Useful Cure Area 8" x 8" 2" x 4" 2" x 2" Typical Lamp Type Metal Halide Visible Arc Lamp Visible Arc Lamp Output Intensity Medium Low High Lamp Power 400 W 400 W,500 W Optional Shutter Assembly N/A N/A Optimized Spectral Output Range UVA Proprietary Visible Blue and Green Replacement Bulbs (Item Number / Type) Loctite UV Lamp Watt Metal Halide Loctite Visible Light Enhanced Metal Halide Bulb Visible Arc Lamp, 400 W Visible Arc Lamp,,500 W Replacement Filter Glass * 9882 Loctite ZETA 7420, is a 230 VAC/50 Hz system. 09

112 Cure Chambers & Flood Systems LIGHT CURE LOCTITE ZETA 74-S UV FLOOD SYSTEM Item Number: 9843 The Loctite ZETA 74-S UV Flood System is designed for use in a wide range of bonding, potting, tacking and sealing applications. Because of its reliability and simplicity, it is well suited for most production operations. The Loctite ZETA 74-S can accept multiple part sizes. An optional timed control shutter (as displayed) or visible enhanced metal halide lamp are also available. Contains a 4", 400 watt metal halide bulb** Optimized to emit in the UVA region Typical curing area of 8" x 8",000 hours of expected UV bulb life with proper handling and maintenance Power supply can be separated from the lamp base assembly Lamp height is adjustable to a maximum height of 3 4" from pad Contains a glass filter to reduce the short and medium wavelength lamp emissions The work surface is covered by a special silicone rubber pad to resist UV deterioration and chemical attack Shown with Optional Shutter Assembly The operator places the assembly to be bonded into the cure area, allows the assembly to be exposed for the proper time, and manually removes the cured assembly. In addition, the light source can be pulled from the power supply and mounted over a conveyor belt for a more automated use of the equipment. Utilities 20 VAC; 8 amps; 60 Hz ** See page 09 for spectral output chart for a metal halide bulb. Lamp Type, (Visible and UV enhanced) 400 watt Metal Halide Dimensions 27.0" H x 2.7" W x 4.0" D Weight 37 lbs. Parts Included () Reusable Shipping Box Foam Packaging For proper eye protection, use Item () Height Adjustment for Reflector Housing Loctite brand ultraviolet () Reflector Housing with Flexible UV safety glasses. Curtain Shield Attached () UV Protective Eyewear () Cotton Gloves () UV Power Supply () Power Cord () Manual Item 9720 Replacement Parts Loctite Replacement Silicone Work Surface Loctite Replacement Filter Glass Loctite Replacement Light Blocking Curtain Loctite UV Lamp watt Metal Halide * Loctite Visible Light Enhanced Metal Halide Bulb Additional Accessories Sold Separately Loctite ZETA 70-A Dosimeter-Radiometer (See page 3) Loctite Time Controlled Shutter Loctite Optional Head Extension Cable * Optional replacement bulb. 0

113 LIGHT CURE Cure Chambers & Flood Systems LOCTITE INDIGO 748 VISIBLE LIGHT FLOOD SYSTEM Item Number: 9703 The Loctite Indigo 748 Visible Light Flood System, item 9703, is a unique visible light flood system designed for curing Loctite 3552 and 3553 Indigo Visible Light Cure Adhesives. This can be used as a high intensity, benchtop modular light cure system. The lamp can be mounted over existing material handling systems such as conveyors. These units can also be stacked side-by-side to increase the effective curing area. This unit includes an operations manual, the lamp with reflector housing, and associated power cords. Contains a 4 inch, 400 watt visible arc bulb Optimized to emit in the visible region (greater than 400 nm) Typical curing area of 2" by 4" Average irradiance of 225 mw/cm 2 at a 2" distance 2000 hours of expected bulb life with proper handling Protective glass to shield the light source from direct contact Allows curing through colored substrates Can achieve cure through depths over 2" The operator places the part under the lamp for the pre- determined exposure time. Upon completion of the exposure time, the operator removes the part from under the lamp. Utilities Dimensions Lamp Weight Ballast Weight Lamp Type Parts Included Replacement Parts 5/230 VAC; 50/60 Hz 5.0" L x 5.25" x 8.0" H 8.5 lbs. 7.5 lbs. 400 watt Visible Arc () Operations Manual () Lamp with Reflector Housing () Power Cord () Ballast Connection Cord Loctite Replacement Ballast Loctite Replacement Filter Glass Loctite 400 Watt Visible Arc Bulb Additional Accessories Sold Separately Loctite ZETA 70-V Dosimeter (See page 3) Safety Glasses (protects from 200 to 540 nm wavelengths) Pair of Cotton Gloves

114 Cure Chambers & Flood Systems LIGHT CURE LOCTITE ZETA 7420 VISIBLE LIGHT FLOOD SYSTEM Item Numbers: and 9882 The Loctite ZETA 7420 Visible Light Flood Systems (98060 with 20 VAC and 9882 with 230 VAC) represent an innovative, extremely cost- effective approach to high-intensity curing. These systems are designed for use in a wide range of bonding, potting, tacking and sealing applications. Their reliability and simplicity are well suited to a variety of production operations. Most Loctite brand light cure adhesives with dual cure capability (UV/Visible) are compatible with these systems, including Loctite brand 303, 305, 306, 307, 3494, 3525, 3526, 4304 and 4305 Light Curing Adhesives. High intensity,500 watt bulb item number Optimized to emit in the visible blue and green region Typical curing area of 2" x 2",000 hours of expected bulb life with proper handling and maintenance Lamp and power supply are separate for installation flexibility Lamp includes mounting chains for easy attachment to customer fixtures Contains a glass filter to reduce the short and medium wavelength lamp emissions The operator places the bonded assembly into the cure area, allows the assembly to be exposed for the proper time, and manually removes the cured assembly. In addition, the light source can be pulled from the power supply and mounted over a conveyor belt for a more automated use of the equipment. Shielding for the high-intensity visible light must be provided by the customer. Utilities Lamp Type, (Visible and UV enhanced) Dimensions Weight Parts Included Replacement Parts VAC; 3.5 amps, 60 Hz Visible Arc Lamp VAC; 7.0 amps, 50 Hz Lamp Head: 9.5" H x 23.6" W x 20.75" D Power Supply: 8.95" H x 7.75" W x 4.9" D 80 lbs. () Lamp with Bulb and Filter Glass () Power Supply () Manual Loctite Replacement Ballast (20 VAC; 60 Hz) Loctite Visible Arc Bulb,,500 watt Loctite Replacement Safety Glass, Tempered Additional Accessories Sold Separately Loctite ZETA 70-V Dosimeter-Radiometer (See page 3) 2

115 Light Meters Decreased radiant power related to the degradation of UV lamps, light guides and reflectors results in declines in process efficiency or incomplete curing of UV light curing products. Loctite ZETA Light Meters are used to check the intensity of ultraviolet light emitted from a light source. These units are useful for quality measures, maintenance, and troubleshooting of ultraviolet emitting light sources. Selection of a Loctite ZETA Light Meter is based on the type of light source that is required to be measured. LIGHT CURE Light Meters LOCTITE ZETA 70-A DOSIMETER-RADIOMETER Item Number: LOCTITE ZETA 70-V DOSIMETER-RADIOMETER Item Number: The Loctite ZETA 70- A and 70- V Dosimeter-Radiometers are self-contained, electro-optic meters that measure and display total energy (J/cm 2 ) and irradiance (W/cm 2 ). They are designed to withstand the extremes of UV light and high temperature that are part of the UV curing environment. The carefully designed optical sensing system measures only certain wavelengths, rejecting those that are not relevant to the process. The output of the sensing system is converted to digital form and displays a liquid crystal readout. The Loctite ZETA 70- A measures across the ultraviolet spectrum from 320 to 400 nanometers (UVA region). The Loctite ZETA 70- V measures across the ultraviolet spectrum from 350 to 500 nanometers (UVV region). These units are designed to monitor the performance of a light curing system. Measures energy and irradiance lamp performance to determine lamp efficiency Establishes energy and irradiance level for proper curing when implementing a new process Calibration is required only once per year Meets ISO-9000 requirements by providing a device that will allow for recording of lamp performance data Dual display of energy and irradiance allows for convenient, same screen viewing Centrally located sensor allows for easy alignment Calibration is traceable to the National Institute of Standard Technology (NIST) Operating Temperature An operator will turn the radiometer on, reset the unit, and place the eye of the unit under the light source for no more than 5 seconds. The reading will be displayed on the liquid crystal readout. 0 C to 75 C internal temperature Note: tolerates much higher external temperatures for short periods; audible alarm indicates when temperature is too high. 5 minutes (if no buttons are pressed) 4 digit LCD Automatic Shut-off Display Measured Spectral ZETA 70-A Range 320 to 400 nm Dimensions 4" L x 4" W x 0.52" D Weight 8.6 oz. (245 g) Power Source Two AAA alkaline batteries (not included) Typical Battery Life 3,000 readings or 2,000 hours Case Material Aluminum, stainless steel Used To Measure Output of 98086: Chambers, Conveyors, Flood Systems ZETA 70-V 350 to 500 nm 98089: Chambers, Conveyors, Flood Systems, LED Light Sources () ZETA Parts Included 70-A or 70-V Dosimeter-Radiometer () Manual Additional Accessories Sold Separately Loctite CureJet LED Dosimeter Adapter [Requires 98089] (See page 02) Adapter for LED intensity measurement 3

116 Light Meters LIGHT CURE LOCTITE ZETA 702 SPOT RADIOMETER Item Number: The Loctite ZETA 702 Spot Radiometer is a self- contained, electro- optic instrument designed to measure and display the UV irradiance emitted by a UV spot curing system. The units displayed are watts per square centimeter (W/cm 2 ). Decreased radiant power related to the degradation of UV lamps, light guides, and reflectors can result in declines in process efficiency or incomplete curing of UV light curing products. The Loctite ZETA 702 is designed to provide the operator with instant feedback as to the performance of the spot curing system. It accepts both 3 mm and 5 mm diameter wands. The unique detachable sensor head requires re-calibration only once per year (vs. every 6 months for competitive models). Requires a 9 volt alkaline battery (not included). Measures UV wand curing system performance Measures UV lamp performance Measures light guide degradation Optimizes dual light guide balancing Determines proper UV intensity required for curing various materials Meets ISO requirements Calibration is traceable to the National Institute of Standard Technology (NIST) An operator will place the UV wand in the opening of the sensor head. The light to be measured will be emitted for approximately 2 to 4 seconds. The reading will immediately be displayed. Radiant Power Range 0 to 9.99 W/cm 2 Resolution 0.0 W/cm 2 Accuracy Display Reading Exposure Time Spectral Range Power Source Dimensions Weight Used to Measure Output of Parts Included ± 5% typical / ± 0% maximum.0" W x 0.5" H LCD 2 to 4 seconds 280 to 400 nm (UVA & B region) 9 volt alkaline battery (not included) 3.0" H x 2.5" W x.2" D 0.4 lbs. 3 mm and 5 mm diameter Wands () ZETA 702 Spot Radiometer () Manual Additional Accessories Sold Separately / 9837A / 9857A / Loctite ZETA or Indigo UV Wand Systems 4

117 Cure Conveyors Loctite brand cure conveyors are used for continuous or batch processing of assemblies. Each conveyor has a unique set of features designed to meet the challenges of benchtop curing of light curing adhesives and coatings. Selection of a Loctite brand cure conveyor is based on the part size, and the required lamp for optimum cure. LIGHT CURE Cure Conveyers LOCTITE ZETA 745 UV BENCHTOP CONVEYOR Item Number: The Loctite ZETA 745 UV Benchtop Conveyor offers variable speed adjustment for low to medium volume production and is designed for use with an electrodeless bulb and a parabolic reflector to create a uniform cure area. The lamp assembly, conveyor, and power supply are ordered separately. The system can be integrated into an automatic or semi- automatic production line for cure- on- demand assembly. Conveyor speeds from 3.3 to 23 feet per minute or 0.3 to 7.2 feet per minute Typical curing area width of 6 inches Lamp orientation and height are adjustable for variable cure focal points Integrated modular blower for lamp cooling An operator will assemble the desired parts with a light curing adhesive or sealant, place the assembly on the conveyor with a preset belt speed and lamp height, and allow the assembly to pass through the conveyor to the other side, where the assembly should be removed. Conveyor Utilities 7 VAC single phase, amp, 50 to 60 Hz or can be configured for 230 VAC single phase 98004* Power Supply Utilities 208 VAC single phase; 8 amps; 50/60 Hz 98005* Power Supply Utilities 240 VAC single phase; 8 amps; 50/60 Hz Maximum Part Size 7.5" W x 3" H Conveyor Size 27.4" H x 42" W x 20" D Conveyor Weight 85 lbs. Power Supply Size 8" H x 9.9" W x 23" D Useful Cure Area 6" x 6" Optimized Spectral Output Range UVA, B, C* Parts Included () Loctite ZETA 745 UV Benchtop Conveyor* () Ultraviolet Protection Glasses () Manual Additional Accessories Sold Separately Loctite ZETA 70-A Dosimeter-Radiometer Loctite ZETA 70-V Dosimeter-Radiometer Loctite Air Deflection Kit, High Grade Quartz Loctite Sight Shield, Snap In, Tunnel Style Loctite Sight Shield, Snap In, Box End Style Loctite Exhaust Plenum Loctite Fusion V Bulb W/in Loctite Fusion D Bulb W/in Loctite Fusion H Bulb W/in. * The lamp assembly is sold separately; see the Light Sources section for more details on pages

118 Cure Conveyers LIGHT CURE LOCTITE ZETA 760 UV BENCHTOP CONVEYOR Item Number: The Loctite ZETA 760 is a benchtop, ultraviolet curing conveyor used to cure light cure adhesives and coatings. This conveyor has a medium pressure mercury arc lamp which produces high- intensity ultraviolet energy in the UVA, UVB, and UVC spectral region. This system can be integrated into an automatic or semi- automatic production line for cure- on- demand assembly. 6 inch, medium pressure mercury arc lamp Lamp height can be adjusted to vary intensity Variable bulb wattage: 50 or 300 watts per inch to accommodate heat sensitive applications Optimized to emit in the UVA, UVB, and UVC regions Typical curing width 6 5 8" with 6" maximum part height,000 hours of expected UV bulb life with proper handling and maintenance Variable conveyor speed up to 56 feet per minute Vacuum hold down for lightweight substrates The Loctite ZETA 760 is a benchtop, ultraviolet curing conveyor used to cure light cure adhesives and coatings. This conveyor has a medium pressure mercury arc lamp which produces high- intensity ultraviolet energy in the UVA, UVB, and UVC spectral region. This system can be integrated into an automatic or semi- automatic production line for cure- ondemand assembly. Gamma Rays The Electromagnetic Spectrum / ev UV UV Visible Light nm Visible Light Radiation Energy Infra-Red Microwaves Radiowaves Wavelength VUV UVC UVB UVA Blue Green Yellow Red nm Input Power Required Power Consumption at 300 W/in. Setting Belt Maximum Part Weight: Belt speed range (Minimum to Maximum) Lamp Maximum Part Cross Section Dimensions Weight Parts Included Replacement Bulb 20 VAC; phase; 50/60 Hz; fused for 2 amps Approximately 2,200 watts 304 stainless steel wire 3 pounds to 20.0 inch/second 60 to,200 inch/minute 0 to 56 feet/minute,800 watt Medium Pressure Mercury Arc Lamp 6" H x 6.625" W 3.6" H x 3.8" W x 23.8" D 45 lbs. () Loctite ZETA 760 UV Benchtop Conveyor () Ultraviolet Lamp () Ultraviolet Protection Glasses () Pair of Cotton Gloves () Manual Replacement 6" UV Bulb W/in. Additional Accessories Sold Separately Loctite ZETA 70-A Dosimeter-Radiometer 6

119 Light Sources Our light sources and power supplies provide high intensity ultraviolet light for curing light cure adhesives and coatings. These units are designed to be integrated into a Loctite brand conveyor system, or used when the end user provides the conveyor and shielding requirements. Selection of a light source and power supply is based on the bulb type, electrical requirements, and the desired part movement. LIGHT CURE Light Sources LOCTITE ELECTRODELESS LAMP ASSEMBLY AND POWER SUPPLY Item Numbers: VAC single phase, 0 amps, 50/60 Hz Item Numbers: VAC single phase, 0 amps, 50/60 Hz The Loctite Electrodeless Lamp Assembly comes equipped with a long life 6 inch H bulb. The light source is compatible with D, V, H and H+ bulbs to tailor the spectral output of the light to the application. Selection of the or is based on the electrical capabilities available to the end user. The Loctite Electrodeless Lamp Assembly is typically used with the Loctite ZETA 745 UV Benchtop Conveyor. Designed for use with the Loctite ZETA 745 UV Benchtop Conveyor Electrodeless bulb technology provides high intensity output The system is shipped standard with an H bulb, but will accept D, V or H+ bulbs to fine tune lamp spectral output 5,000 hours of expected UV bulb life of the H bulb, with proper handling and maintenance High UV output with low IR output results in less heat to the substrate An operator will assemble parts with a light curing adhesive or coating and manually or automatically place the part under the lamp for cure. Shielding is obtained through the use of this assembly with a Loctite ZETA 745 Benchtop Conveyor. If used elsewhere, shielding must be provided by the customer. 20 Spectral Output of H Bulb Power Supply VAC single phase; 8 amps; 50/60 Hz VAC single phase; 8 amps; 50/60 Hz Lamp Fusion H Bulb W/in. Dimensions 9.9" H x 6.6" W x 0.3" D Parts Included () Fusion Lamp Assembly and Power Supply () Manual Replacement Bulb Fusion H Bulb W/in. Additional Accessories Sold Separately Watts per inch Wavelength in nm Loctite ZETA 70-A Dosimeter- Radiometer Fusion V Bulb W/in Fusion D Bulb W/in Fusion H Bulb W/in. 7

120 Light Sources LIGHT CURE LOCTITE HIGH INTENSITY ULTRAVIOLET SOURCES Item Numbers: and The Loctite High Intensity Ultraviolet Sources are designed for a wide range of applications using ultraviolet curing adhesives and coatings. With the proper shielding, cooling and venting (not included with this product), this light source can be integrated into both prototype and production applications. This unit is designed specifically for the user who wants to integrate their own shielding, cooling, venting and mounting systems into a production line. A 220 VAC, 50 Hz unit is available as item Contains a 5 inch, 300 watts/inch medium pressure mercury vapor bulb Item Number 9806 Variable bulb wattage: 200 or 300 watts/inch Designed to emit in the UVA and UVB regions Typical curing area of 4.5" x 6",000 hours of expected UV bulb life with proper handling and maintenance To assemble a component with a UV curing adhesive or coating, place and remove the part manually or automatically under the light source. The customer will provide their own mounting, shielding, cooling, and venting for this unit. Spectral Output of a Medium Pressure Mercury Arc Bulb Output UV in W Wavelength in nm For proper eye protection, use Loctite brand ultraviolet safety glasses. Item 9720 Item Power Supply Power Consumption Lamp Lamp Unit Size Power Supply Size Lamp Unit Weight Power Supply Weight Parts Included Replacement Bulb VAC; 60 Hz; 5 amp VAC; 50 Hz; 7.5 amp 2,000 Watts 300 watt Medium Pressure Mercury Arc Lamp 5.8" L x 8.7" W x 7.4" H 5.0" L x 4.7" W x 2." H 9 lbs. 45 lbs. () High Intensity UV Source () Ultraviolet Protection Glasses () Manual 9806 Replacement 5" UV Bulb W/in. Additional Accessories Sold Separately Loctite ZETA 70-A Dosimeter-Radiometer 8

121 Index 9 INDEX ITEM NUMBER PRODUCT NAME PAGE NUMBER ITEM NUMBER PRODUCT NAME PAGE NUMBER Loctite 400 ml Mix Nozzle for Dispenser Loctite Fixmaster Rapid Rubber Repair Dispenser , Loctite 404 Quick Set Instant Adhesive, General Purpose Loctite Water Proofing Solvent Loctite Clean-Up Solvent Loctite 250 ml Hand Pump , Loctite 300 ml Pneumatic Cartridge Dispenser , Loctite Precision Syringe Dispensing System ,, 2, 87, 88, 89, 90, Loctite Integrated Semi-Automatic Dispenser, 0 to 00 psi , 9, 59, 6, 65, 66, 67, 68, 7, 87, 88, 89, 90, Loctite Integrated Semi-Automatic Dispenser, 0 to 5 psi , 9, 59, 6, 65, 66, 67, 68, 7, 87, 88, 89, 90, Loctite Integrated Semi-Automatic Dispenser with Low Level Sensor, 0 to 00 psi , 9, 59, 6, 65, 66, 67, 68, 7, 87, 88, 89, 90, Loctite Integrated Semi-Automatic Dispenser with Low Level Sensor, 0 to 5 psi.....5, 6, 9, 59, 6, 65, 66, 67, 68, 7, 87, 88, 89, 90, Loctite 50 ml Dual Cartridge Pneumatic Applicator , Loctite Digital Dispense Controller , 8, 59, 6, 65, 66, 67, 68, 7 97 Loctite Hand Held Manual Applicator , 60, Loctite Hand Held Pneumatic Applicator , 6, Loctite Stationary Applicator Valve , 65, 73, 77, Loctite Stationary Applicator Valve , 65, 73, 77, Loctite Electric Rotorspray for use with , 6, 65, Loctite Hand Held Pneumatic Applicator , 6, Loctite Advancing Slide for use with 9723, 50 mm stroke , 6, Loctite Advancing Slide for use with 9723, 00 mm stroke , 6, Loctite Air Filter and Regulator for Loctite Single Channel Automatic Controller , 6, 59, 65, 66, 67, 68, 7, Loctite LV Hand Held Applicator , 59, Loctite Vari-Drop Applicator with Tubing , 62, Loctite Vari-Drop Applicator without Tubing , 62, 63, 84, Loctite Diaphragm Valve, 2 mm Orifice , 68, Loctite Diaphragm Valve, 3 mm Orifice , 68, Loctite Posi-Link Static Mixer Pinch Valve , Loctite Valve Body Adapter - for and 9803 dispense valves Loctite Replacement Foot Switch , Loctite 0 ml Clear Syringe Barrel Kit Loctite 0 ml Syringe Air Line Adapter , 2, 66, Loctite Ultraviolet Safety Glasses, Grey , 03, Loctite In-Line Flow Monitor , Loctite Cartridge-Syringe Adapter Loctite 0 ml Syringe Starter Kit , 2, Loctite 3/8" Feed Line Conversion Kit , 6, 62, Loctite 6 Gauge, Grey, Taper Tips Loctite 8 Gauge, Green, Taper Tips Loctite 20 Gauge, Pink, Taper Tips Loctite 22 Gauge, Blue, Taper Tips Loctite 5 Gauge, /2", Stainless Steel, Amber Loctite 8 Gauge, /2", Stainless Steel, Green Loctite 20 Gauge, /2", Stainless Steel, Pink Loctite 25 Gauge, /2", Stainless Steel, Red Loctite 5 Gauge, Amber, Helical Thread, flexible polypropylene Loctite 8 Gauge, Green, Helical Thread, flexible polypropylene Loctite 20 Gauge, Pink, Helical Thread, flexible polypropylene Loctite 25 Gauge, Red, Helical Thread, flexible polypropylene Loctite Luer-Lok Adapter Kit , Loctite Replacement Finger Level for Loctite Replacement Actuator for Loctite Replacement Actuator for Loctite 25 Gauge, Stainless Steel, PTFE Lined, ID 0.58 mm, Pink Loctite Replacement Shut-Off Valve Assembly for Loctite Replacement Shut-Off Valve Assembly for Loctite Mounting Bracket Loctite 30 ml Clear Syringe Barrel Kit , 2, Loctite 55 ml Syringe Air Line Adapter , 2, 66, Loctite Replacement UV Lamp for or W/in , Loctite Dispense Needle Tip Caps Loctite Vari-Drop Applicator Repair Kit , Loctite Replacement Rupture Disc Loctite Diaphragm Valve Actuator Replacement Loctite 5 Gauge, High Density Polyethylene, I.D..25 mm, White Loctite Needle Assortment Kit , Loctite 0 ml Black Syringe Barrel Kit for UV Adhesives Loctite 30 ml Black Syringe Barrel Kit for UV Adhesives Loctite Diaphragm Valve Shut-Off 2 mm replacement Loctite Diaphragm Valve Shut-Off 3 mm replacement Loctite Diaphragm Replacement Kit Loctite Replacement Actuator Assembly Loctite Finger Switch, LV Hand Held Applicator Loctite 30 ml Syringe Starter Kit , 2, Loctite Valve Body Adapter - for 973 and 974 dispense valves Loctite UV Single Light Guide, Enhanced UVC, 5 mm x 000 mm Loctite UV DUAL Light Guide, Enhanced UVC, 3 mm x 000 mm Loctite Tri-Nozzle Loctite Replacement Tube Inserts (0 pack) Loctite Repair Kit for LV Hand Held Applicator Loctite Pneumatic Tubing, 4 mm OD Loctite 3/8" Black PTFE Lined Feed Tube Loctite /4" Black PTFE Lined Feed Tube Loctite Pneumatic Tubing, 6 mm OD Loctite Replacement Valve Assembly Loctite ZETA 745 UV Benchtop Conveyor , Fusion 208V Lamp Assembly and Power Supply , Fusion 240V Lamp Assembly and Power Supply , Loctite Light Cure Dispense Valve , 67, 73, 77, Loctite Hysol Reactive Urethane Cartridge Dispenser , Loctite Cartridge Pre-Heater , Loctite Cyanoacrylate Dispense Valve , 67, 73, Loctite 300 ml Cartridge Pusher , 2, 6, 62, 65, 67, Loctite 30 ml Manual Syringe Applicator , Loctite Hysol 075 Hot Melt Applicator , Loctite Hysol 075-LT Hot Melt Applicator , Loctite Hysol 75 Hot Melt Applicator , Loctite Hysol 75-AIR Hot Melt Applicator , Loctite Hysol 75-SPRAY Hot Melt Applicator , Loctite ZETA 740 UV Chamber , Loctite Hysol 75-AIR-HT Hot Melt Applicator , Loctite Hysol 75-SPRAY-HT Hot Melt Applicator , Loctite Hot Melt Bench Mount Kit , 46, Loctite Hot Melt Pneumatic Timer , 46, Loctite ZETA 702 Spot Radiometer , 03, 05, 06, 07, Loctite Foot Pedal Dispenser , Loctite Foot Pedal Dispenser , Loctite ZETA 7420 Visible Light Flood System, 20 VAC , 09, Loctite 6 Gauge, Grey, Taper Tips Loctite 8 Gauge, Green, Taper Tips Loctite 20 Gauge, Pink, Taper Tips Loctite 22 Gauge, Blue, Taper Tips Loctite 5 Gauge, 2", Stainless Steel, Amber Loctite 8 Gauge, /2", Stainless Steel, Green Loctite 20 Gauge, /2", Stainless Steel, Pink Loctite 25 Gauge, /2", Stainless Steel, Red Loctite 5 Gauge, Amber, Helical Thread, Flexible Polypropylene Loctite 8 Gauge, Green, Helical Thread, Flexible Polypropylene Loctite 20 Gauge, Pink, Helical Thread, Flexible Polypropylene Loctite 25 Gauge, Red, PTFE Lined, Helical Thread Loctite 5 Gauge, White, HD Polyethylene Loctite Shot Miser Valve Controller , 5, 8, 59, Loctite 22 Gauge, /2", Stainless Steel, Blue Loctite 25 Gauge, Red, Helical Thread, Flexible Polypropylene Loctite Fluorescence Detector Loctite Micro Needle Valve , 66, Loctite Shot Miser Dispense Valve , 64, 7, Loctite ZETA 70-A Dosimeter-Radiometer , 08, 09, 0, 3, 5, 6, 7, Loctite ZETA 70-V Dosimeter-Radiometer , 00, 0, 02,, 2, 3, Loctite Shot Miser Liter Reservoir, 0 to 00 psi , 5, 22, 59, Loctite Micro Needle Valve Rod Replacement kit Loctite Toggle Valve for Loctite Precision Filter and Regulator for use with Loctite 22 Gauge, /2", Stainless Steel, Blue Loctite Lens, 50 mm Distance, for use with Loctite Lens, 9 mm Distance, for Loctite Lens, 28 mm Distance, for Loctite 30 Gauge, /2", Stainless Steel, Lavender, Helical Thread Loctite 30 Gauge, /2", Stainless Steel, Lavender, Helical Thread Loctite 32 Gauge, /4", Stainless Steel, Yellow, Helical Thread Loctite 32 Gauge, /4", Stainless Steel, Yellow, Helical Thread Loctite 30 ml Syringe Barrel, Black (500 pack) Loctite 3 ml Syringe Piston (,000 pack) Loctite Foot Pedal for Loctite 0 ml Syringe Piston (,000 pack) Loctite Cartridge Dispense Tip (0 pack) Loctite Pressure Regulator for Loctite Pressure Gauge for Loctite Hysol Bulk-2 Hot Melt System, 5V , Loctite Hysol Bulk-2 Hot Melt System, 230V , Loctite Hysol Bulk-4 Hot Melt System, 5V , Loctite Hysol Bulk-4 Hot Melt System, 230V , Loctite Hysol Bulk-34 Hot Melt System, 230V , Loctite Hysol Hand Held Top Inlet Applicator, 5 VAC Loctite Hysol Hand Held Top Inlet Applicator, 230 VAC Loctite Hysol Hand Held Bottom Inlet Applicator, 5 VAC Loctite Hysol Hand Held Bottom Inlet Applicator, 230 VAC Loctite Hysol 2 Hand Applicator, 5 VAC / 5 VAC Loctite Hysol 2 Hand Applicator, 230 VAC with 230 VAC Control Coil Loctite Hysol 2 Hand Applicator, 230 VAC with 5 VAC Control Coil Loctite Hysol 2 Hand Applicator, 5 VAC with 24 VDC Control Coil Loctite Hysol 2 Hand Applicator, 230 VAC with 24 VDC Control Coil Loctite Hysol Mounted Applicator, 230 VAC with 24 VDC Control Coil Loctite Hysol Mounted Applicator, 5 VAC with 24 VDC Control Coil

122 20 INDEX ITEM NUMBER PRODUCT NAME PAGE NUMBER ITEM NUMBER PRODUCT NAME PAGE NUMBER 9847 Loctite Hysol Mounted Applicator, 5 VAC with 5 VAC Control Coil Loctite Hysol Mounted Applicator, 230 VAC with 230 VAC Control Coil Loctite Hysol Mounted Applicator, 230 VAC with 5 VAC Control Coil A Loctite ZETA 7740 Light Cure Wand System , 03, 06, Loctite Hysol 2 Event Timer, 5/230 VAC Loctite Hysol 4 Event Timer, 5/230 VAC Loctite Foot Switch, Bulk Hot Melt System Loctite Hysol Spray Controller, 5 VAC Loctite Hysol Spray Controller, 230 VAC Loctite 4 Gauge,.5", Stainless Steel, White, Helical Thread Loctite 4 Gauge,.5", Stainless Steel, White, Helical Thread Loctite 5 Gauge,.5", Stainless Steel, Amber, Helical Thread Loctite 5 Gauge,.5", Stainless Steel, Amber, Helical Thread Loctite 8 Gauge,.5", Stainless Steel, Green, Helical Thread Loctite 8 Gauge,.5", Stainless Steel, Green, Helical Thread Loctite 20 Gauge,.5", Stainless Steel, Pink, Helical Thread Loctite 20 Gauge,.5", Stainless Steel, Pink, Helical Thread Loctite 2 Gauge,.5", Stainless Steel, Purple, Helical Thread Loctite 2 Gauge,.5", Stainless Steel, Purple, Helical Thread Loctite 22 Gauge,.5", Stainless Steel, Blue, Helical Thread Loctite 22 Gauge,.5", Stainless Steel, Blue, Helical Thread Loctite 23 Gauge,.5", Stainless Steel, Orange, Helical Thread Loctite 23 Gauge,.5", Stainless Steel, Orange, Helical Thread Loctite 25 Gauge,.5", Stainless Steel, Red, Helical Thread Loctite 25 Gauge,.5", Stainless Steel, Red, Helical Thread Loctite 27 Gauge,.5", Stainless Steel, Grey, Helical Thread Loctite 27 Gauge,.5", Stainless Steel, Grey, Helical Thread Loctite 300 ml Cartridge Tube Fitting Adapter, for / (3 pack) Loctite ZETA 7420 Visible Light Flood System, 230 VAC , 09, Loctite Manual Plunger for 0 ml Syringe , Loctite Manual Plunger for 30 ml Syringe , Loctite 8 Gauge, /4", Stainless Steel, Green, Helical Thread Loctite 8 Gauge, /4", Stainless Steel, Green, Helical Thread Loctite 20 Gauge, /4", Stainless Steel, Pink, Helical Thread Loctite 20 Gauge, /4", Stainless Steel, Pink, Helical Thread Loctite 2 Gauge, /4", Stainless Steel, Purple, Helical Thread Loctite 2 Gauge, /4", Stainless Steel, Purple, Helical Thread Loctite 4 Gauge, /2", Stainless Steel, Olive Loctite 4 Gauge, /2", Stainless Steel, Olive Loctite 2 Gauge, /2", Stainless Steel, Purple Loctite 2 Gauge, /2", Stainless Steel, Purple Loctite 23 Gauge, /2", Stainless Steel, Orange Loctite 23 Gauge, /2", Stainless Steel, Orange, Loctite 27 Gauge, /2", Stainless Steel, Clear Loctite 27 Gauge, /2", Stainless Steel, Clear Loctite 4 Gauge, ", Stainless Steel, White, Helical Thread Loctite 4 Gauge, ", Stainless Steel, White, Helical Thread Loctite 5 Gauge, ", Stainless Steel, Amber, Helical Thread Loctite 5 Gauge, ", Stainless Steel, Amber, Helical Thread Loctite 8 Gauge, ", Stainless Steel, Green, Helical Thread Loctite 8 Gauge, ", Stainless Steel, Green, Helical Thread Loctite 20 Gauge, ", Stainless Steel, Pink, Helical Thread Loctite 20 Gauge, ", Stainless Steel, Pink, Helical Thread Loctite 2 Gauge, ", Stainless Steel, Purple, Helical Thread Loctite 2 Gauge, ", Stainless Steel, Purple, Helical Thread Loctite 22 Gauge, ", Stainless Steel, Blue, Helical Thread Loctite 22 Gauge, ", Stainless Steel, Blue, Helical Thread Loctite 23 Gauge, ", Stainless Steel, Orange, Helical Thread Loctite 23 Gauge, ", Stainless Steel, Orange, Helical Thread Loctite 25 Gauge, ", Stainless Steel, Red, Helical Thread Loctite 25 Gauge, ", Stainless Steel, Red, Helical Thread Loctite 27 Gauge, ", Stainless Steel, Grey, Helical Thread Loctite 27 Gauge, ", Stainless Steel, Grey, Helical Thread Loctite 4 Gauge, 45, /2", Stainless Steel, White, Helical Thread Loctite 4 Gauge, 45, /2", Stainless Steel White, Helical Thread Loctite 4 Gauge, 90, /2", Stainless Steel, White, Helical Thread Loctite 4 Gauge, 90, /2", Stainless Steel, White, Helical Thread Loctite 5 Gauge, 45, /2", Stainless Steel, Amber, Helical Thread Loctite 5 Gauge, 45, /2", Stainless Steel, Amber, Helical Thread Loctite 5 Gauge, 90, /2", Stainless Steel, Amber, Helical Thread Loctite 5 Gauge, 90, /2", Stainless Steel, Amber, Helical Thread Loctite 8 Gauge, 45, /2", Stainless Steel, Green, Helical Thread Loctite 8 Gauge, 45, /2", Stainless Steel, Green, Helical Thread Loctite 8 Gauge, 90, /2", Stainless Steel, Green, Helical Thread Loctite 8 Gauge, 90, /2", Stainless Steel, Green, Helical Thread Loctite 20 Gauge, 45, /2", Stainless Steel, Pink, Helical Thread Loctite 20 Gauge, 45, /2", Stainless Steel, Pink, Helical Thread Loctite 20 Gauge, 90, /2", Stainless Steel, Pink, Helical Thread Loctite 20 Gauge, 90, /2", Stainless Steel, Pink, Helical Thread Loctite 2 Gauge, 45, /2", Stainless Steel, Purple, Helical Thread Loctite 2 Gauge, 45, /2", Stainless Steel, Purple, Helical Thread Loctite 2 Gauge, 90, /2", Stainless Steel, Purple, Helical Thread Loctite 2 Gauge, 90, /2", Stainless Steel, Purple, Helical Thread Loctite 22 Gauge, 45, /2", Stainless Steel, Blue, Helical Thread Loctite 22 Gauge, 45, /2", Stainless Steel, Blue, Helical Thread Loctite 22 Gauge, 90, /2", Stainless Steel, Blue, Helical Thread Loctite 22 Gauge, 90, /2", Stainless Steel, Blue, Helical Thread Loctite 23 Gauge, 45, /2", Stainless Steel, Orange, Helical Thread Loctite 23 Gauge, 45, /2", Stainless Steel, Orange, Helical Thread Loctite 23 Gauge, 90, /2", Stainless Steel, Orange, Helical Thread Loctite 23 Gauge, 90, /2", Stainless Steel, Orange, Helical Thread Loctite 25 Gauge, 45, /2", Stainless Steel, Red, Helical Thread Loctite 25 Gauge, 45, /2", Stainless Steel, Red, Helical Thread Loctite 25 Gauge, 90, /2", Stainless Steel, Red, Helical Thread Loctite 25 Gauge, 90, /2", Stainless Steel, Red, Helical Thread Loctite 27 Gauge, 45, /2", Stainless Steel, Grey, Helical Thread Loctite 27 Gauge, 45, /2", Stainless Steel, Grey, Helical Thread Loctite 27 Gauge, 90, /2", Stainless Steel, Grey, Helical Thread Loctite 27 Gauge, 90, /2", Stainless Steel, Grey, Helical Thread Loctite 4 Gauge, Tan, Taper Tips Loctite 4 Gauge, Tan, Taper Tips Benchtop Fume Filtration System with Arm A Loctite 203 Benchtop Robot, 200 x 200 mm, 3 axis, 0V , A Loctite 203 Benchtop Robot, 200 x 200 mm, 3 axis, 0V, CE Rated , A Loctite 203 Benchtop Robot, 200 x 200 mm, 3 axis, 220V , A Loctite 203 Benchtop Robot, 200 x 200 mm, 3 axis, 220V, CE Rated , A Loctite 204 Benchtop Robot, 200 x 200 mm, 4 axis, 0V , A Loctite 204 Benchtop Robot, 200 x 200 mm, 4 axis, 0V, CE Rated , A Loctite 204 Benchtop Robot, 200 x 200 mm, 4 axis, 220V , A Loctite 204 Benchtop Robot, 200 x 200 mm, 4 axis, 220V, CE Rated , A Loctite 303 Benchtop Robot, 300 x 320 mm, 3 axis, 0V , A Loctite 303 Benchtop Robot, 300 x 320 mm, 3 axis, 0V, CE Rated , A Loctite 303 Benchtop Robot, 300 x 320 mm, 3 axis, 220V , A Loctite 303 Benchtop Robot, 300 x 320 mm, 3 axis, 220V, CE Rated , A Loctite 304 Benchtop Robot, 300 x 320 mm, 4 axis, 0V , A Loctite 304 Benchtop Robot, 300 x 320 mm, 4 axis, 0V, CE Rated , A Loctite 304 Benchtop Robot, 300 x 320 mm, 4 axis, 220V , A Loctite 304 Benchtop Robot, 300 x 320 mm, 4 axis, 220V, CE Rated , A Loctite 403 Benchtop Robot, 400 x 400 mm, 3 axis, 0V , A Loctite 403 Benchtop Robot, 400 x 400 mm, 3 axis, 0V, CE Rated , A Loctite 403 Benchtop Robot, 400 x 400 mm, 3 axis, 220V , A Loctite 403 Benchtop Robot, 400 x 400 mm, 3 axis, 220V, CE Rated , A Loctite 404 Benchtop Robot, 400 x 400 mm, 4 axis, 0V , A Loctite 404 Benchtop Robot, 400 x 400 mm, 4 axis, 0V, CE Rated , A Loctite 404 Benchtop Robot, 400 x 400 mm, 4 axis, 220V , A Loctite 404 Benchtop Robot, 400 x 400 mm, 4 axis, 220V, CE Rated , Loctite Liter Collapsible Bottle Holder , Loctite 55 ml Clear Syringe Barrel Kit Loctite 55 ml Black Syringe Barrel Kit for UV Adhesives Loctite 30 ml Mounting Bracket Kit A Loctite ZETA 7735 UV Wand System , 03, 05, Loctite 300 ml Cartridge Mounting Bracket Kit A Loctite 300 ml Pneumatic Cartridge Dispensing Retainer , Loctite 0 ml Adapter Loctite 5 ml Adapter Loctite 3 ml Adapter Loctite 360 Rotation Conversion Kit Loctite Mounting Bracket Kit for and Loctite Mounting Bracket Kit for 973 and Loctite Mounting Rail, 3 3/4" Loctite Mounting Rail, 8 3/4" Loctite Mounting Rail, 2" Loctite Tip Locator Bracket for 30 ml Loctite Tip Locator Bracket for 300 ml Loctite Tip Locator Bracket for Valve Loctite Tip Locator for 973 Valve Loctite 4 Axis Robot Mounting Adapter Loctite SCARA Robot Mounting Plate Replacement 50W Lamp/Reflector Module , Loctite 30 ml Syringe Holder for SCARA Loctite 300 ml Syringe Holder for SCARA Loctite Valve Holder for SCARA Loctite Valve Holder for SCARA Loctite Ribbon Tip Adapter 0 mm mix nozzles (0 pack) Loctite Soft Squeeze Bottle, 2 oz , Loctite Soft Squeeze Bottle, 4 oz , Loctite Soft Squeeze Bottle, 8 oz , Loctite Dunce Cap, 2 oz. Bottle Loctite Dunce Cap, 4 to 8 oz. Bottles Loctite Luer-Slip Cap, 2 oz. Bottle Loctite Luer-Slip Cap, 4 to 8 oz. Bottle Loctite Robot Z-Height Adjustment Plate Loctite 2.25 Gallon Pressure Reservoir , Loctite Pressure Relief Valve Kit for Loctite Pressure Regulator for Reservoir Loctite Pressure Gauge for Reservoir Loctite Lid Gasket for Reservoir Buna N Loctite Stepped Tip-Luer, 50 ml, 20 elements (2,000 pack) Loctite 50 ml Square Mix Nozzle, 6 elements (,000 pack) Loctite 200 / 400 ml Mix Nozzle, Snap Tip, 9.3 mm (,000 pack) Loctite Cartridge Needle Luer-Lok Adapter Loctite 200 / 400 ml Sq Mix Nozzle, Luer/Stepped Combo, 5.0 mm (0 pack) Loctite 200 / 400 ml Sq Mix Nozzle, Luer/Stepped Combo, 5.0 mm (,000 pack) Loctite Lid Gasket for Reservoir EP Loctite Posi-Link Controller , 0, 30, 3, 87, 88, 89, 90, Loctite Posi-Link 5-25 Actuator , Loctite Posi-Link 0-50 Actuator , 0, 30, Loctite Posi-Link Actuator , 3

123 2 INDEX ITEM NUMBER PRODUCT NAME PAGE NUMBER ITEM NUMBER PRODUCT NAME PAGE NUMBER Loctite 4 Gauge, White, Helical Thread, Taper Tips Loctite 4 Gauge, White, Helical Thread, Taper Tips Loctite 6 Gauge, Grey, Helical Thread, Taper Tips Loctite 6 Gauge, Grey, Helical Thread, Taper Tips Loctite 8 Gauge, Green, Helical Thread, Taper Tips Loctite 8 Gauge, Green, Helical Thread, Taper Tips Loctite 20 Gauge, Pink, Helical Thread, Taper Tips Loctite 20 Gauge, Pink, Helical Thread, Taper Tips Loctite 22 Gauge, Blue, Helical Thread, Taper Tips Loctite 22 Gauge, Blue, Helical Thread, Taper Tips Loctite Benchtop Interface Cable for Benchtop Robots , 88, 89, 90, Loctite 5 Gauge, /2", Stainless Steel, Amber, Helical Thread Loctite 5 Gauge, /2", Stainless Steel, Amber, Helical Thread Loctite 8 Gauge, /2", Stainless Steel, Green, Helical Thread Loctite 8 Gauge, /2", Stainless Steel, Green, Helical Thread Loctite 20 Gauge, /2", Stainless Steel, Pink, Helical Thread Loctite 20 Gauge, /2", Stainless Steel, Pink, Helical Thread Loctite 22 Gauge, /2", Stainless Steel, Blue, Helical Thread Loctite 22 Gauge, /2", Stainless Steel, Blue, Helical Thread Loctite 25 Gauge, /2", Stainless Steel, Red, Helical Thread Loctite 25 Gauge, /2", Stainless Steel, Red, Helical Thread Loctite Poppet Valve Mounting Bracket Kit Loctite Tip Locator Bracket Loctite Poppet Valve Holder for SCARA Loctite 200 / 400 ml Mix Nozzle, Stepped, 0 mm (,000 pack) Loctite 2 mm Ribbon Tip (500 pack) Loctite 25 mm Ribbon Tip (500 pack) Loctite 43 mm Ribbon Tip (500 pack) Loctite ZETA 74-S UV Flood System , 09, Loctite 50 ml Hand Pump , Loctite Caulking Gun Converter Kit, 50 ml, 0: , Loctite 55 ml Syringe Starter Kit , 2, Loctite Optional Shutter for Loctite 2 Gauge /2" Stainless Steel, Purple Helical Thread Loctite 2 Gauge /2" Stainless Steel, Purple Helical Thread Loctite Advancing Slide Dispense Station , Loctite Single Rotary Dispense Station , Loctite Dual Rotary Dispense Station , Loctite 200 / 400 ml Mix Nozzle, 40 elements, Threaded Bell End (500 pack) Loctite Showcase Needle Variety Kit Loctite LED 7700 On/Off Foot Switch Loctite Micro Needle Valve Mounting Bracket Kit for and Loctite Control Timer Loctite 50 ml Square Mix Nozzle, 6 elements (0 pack) Loctite Light Cure Acrylic Adhesive Dispensing system , Loctite Roller Assembly, " wide band Loctite Replacement Rollers, " wide Loctite Roller Assembly, 2" wide band Loctite Replacement Rollers, 2" wide Loctite ZETA 7760 UV Wand , 03, 07, Loctite Lamp / Reflector Module, 200 W for ZETA , Loctite UV Safety Glasses, Orange , 00, 0, 02, 04, 08, 0, Loctite Dosimeter Adapter for Intensity Measurement , 0, Loctite 50 ml Mix Nozzle, Luer Tip, 6.0 mm (0 pack) Loctite 50 ml Mix Nozzle, Stepped, 6.0 mm (0 pack) Loctite 200 / 400 ml Mix Nozzle, Stepped, 6 mm (0 pack) Loctite 200 / 400 ml Mix Nozzle, Stepped, 8 mm Loctite Luer-Lok Adapter for 6.0 mm and 8 mm Mix Nozzles Loctite 200 / 400 ml Mix Nozzle, Stepped, 0 mm (0 pack) Loctite 200 / 400 ml Mix Nozzle, Stepped, 8 mm (0 pack) Loctite 200 / 400 ml Mix Nozzle, Stepped, 0 mm (0 pack) Loctite 50 ml Mix Nozzle, Stepped, 6.0 mm (4,000 pack) Loctite 50 ml Mix Nozzle, Stepped, 5.4 mm (0 pack) Loctite 200 / 400 ml Mix Nozzle, Stepped, 8 mm (,500 pack) Loctite Caulking Gun Converter Kit for 50 ml Cartridges , Loctite 200 / 400 ml Snap Tip Mix Nozzle (0 pack) Loctite 200 / 400 ml Snap Tip Mix Nozzle (0 pack) Loctite Snap Tip Mix Nozzle and Ribbon Tip Sample Kit Loctite 50 ml Dual Cartridge Manual Applicator , Loctite 50 ml Square Mix Nozzle, 5.3 mm (0 pack) Loctite 200 / 400 ml Square Mix Nozzle, 7.5 mm (0 pack) Loctite 2 mm Ribbon Tip (0 pack) Loctite 25 mm Ribbon Tip (0 pack) Loctite 43 mm Ribbon Tip (0 pack) Loctite 3 ml Syringe Barrel and Piston, Natural (50 pack) Loctite 3 ml Syringe Barrel and Piston, Natural (,000 pack) Loctite 3 ml Syringe Barrel and Piston, Black (50 pack) Loctite 3 ml Syringe Barrel and Piston, Black (,000 pack) Loctite 5 ml Syringe Barrel and Piston, Natural (50 pack) Loctite 5 ml Syringe Barrel and Piston, Natural (50 pack) Loctite 5 ml Syringe Barrel and Piston, Natural (50 pack) Loctite 5 ml Syringe Barrel and Piston, Natural (50 pack) Loctite 0 ml Syringe Barrel and Piston, Natural (50 pack) Loctite 0 ml Syringe Barrel and Piston, Natural (,000 pack) Loctite 0 ml Syringe Barrel and Piston, Black (50 pack) Loctite 0 ml Syringe Barrel and Piston, Black (,000 pack) Loctite 30 ml Syringe Barrel and Piston, Natural (50 pack) Loctite 30 ml Syringe Barrel and Piston, Natural (500 pack) Loctite 30 ml Syringe Barrel and Piston, Black (50 pack) Loctite 30 ml Syringe Barrel and Piston, Black (500 pack) Loctite 55 ml Syringe Barrel and Piston, Natural (250 pack) Loctite 55 ml Syringe Barrel and Piston, Natural (50 pack) Loctite 55 ml Syringe Barrel and Piston, Black (50 pack) Loctite 55 ml Syringe Barrel and Piston, Black (250 pack) Loctite Dispense Needle Tip Caps Loctite Foldable 300 ml Cartridge Applicator , Loctite Applicator Holder , 0,, 2, 59, 60, 6, 62, 83, Loctite Spray Valve , 69, Loctite Spray Valve Controller , 7, 69, 87, 88, 89, 90, Loctite LED Holder Loctite Light Guide, 5 mm x 500 mm, Enhanced UVC Loctite Hysol 050 Hot Melt Applicator , Loctite Hysol 050-HT Hot Melt Applicator , Loctite Benchtop Peristaltic Dispenser , 6, 87, 88, 89, 90, Loctite Robot Interface Box , 88, 89, 90, Loctite 3 ml Syringe Barrel, Natural (,000 pack) Loctite 5 ml Syringe Barrel, Natural (,000 pack) Loctite 0 ml Syringe Barrel, Natural (,000 pack) Loctite 30 ml Syringe Barrel, Natural (500 pack) Loctite 55 ml Syringe Barrel, Natural (250 pack) Loctite 5 ml Syringe Barrel, Black (,000 pack) Loctite 0 ml Syringe Barrel, Black (,000 pack) Loctite 55 ml Syringe Barrel, Black (250 pack) Loctite 5 ml Syringe Piston (,000 pack) Loctite 30 / 55 ml Syringe Piston (,000 pack) Loctite ZETA 760 UV Benchtop Conveyer , Loctite 7700 Hand Held LED , 00, Loctite Light Guide, 3 mm x 000 mm, 3 POLE, Enhanced UVC Loctite Light Guide, 3 mm x 000 mm, 4 POLE, Enhanced UVC Loctite 7703 LED Light Source , 00, Loctite Light Guide, 3 mm x 000 mm, 3 POLE, Loctite Light Guide, 3 mm x 000 mm, 4 POLE, Loctite IR Filter Kit , Loctite 7700-HD LED Light Source , Loctite 500 Benchtop Robot, 50 mm x 50 mm, 3 axis, 0V , Loctite 500 Benchtop Robot, 50 mm x 50 mm, 3 axis, 0V CE Rated , Loctite 500 Benchtop Robot, 50 mm x 50 mm, 3 axis, 220V , Loctite 500 Benchtop Robot, 50 mm x 50 mm, 3 axis, 220V CE Rated , Loctite 500 Benchtop Robot, 50 mm x 50 mm, 4 axis, 0V , Loctite 500 Benchtop Robot, 50 mm x 50 mm, 4 axis, 0V CE Rated , Loctite 500 Benchtop Robot, 50 mm x 50 mm, 4 axis, 220V , Loctite 500 Benchtop Robot, 50 mm x 50 mm, 4 axis, 220V CE Rated , Loctite 3/4" wide x /4" NPT Dispense Nozzle Loctite Needle, 23 gauge, Helix, /2" Stainless Steel (50 pack) Loctite Needle, 23 gauge, Helix, /2" Stainless Steel (,000 pack) Loctite Precision O-Ring Cut and Splice Tool Loctite 50 ml Mix Nozzle, 20 elements, Luer (0 pack) Loctite 50 ml Mix Nozzle, 20 elements, Step (0 pack) Loctite Needle, 25 gauge, /4" Stainless Steel, Red (50 pack) Loctite Needle, 25 gauge, /4" Stainless Steel, Red (,000 pack) Loctite Needle, 27 gauge, /4" Stainless Steel, Clear (50 pack) Loctite Needle, 27 gauge, /4" Stainless Steel, Clear (,000 pack) Loctite Needle, 30 gauge, /4" Stainless Steel, Lavender (50 pack) Loctite Needle, 30 gauge, /4" Stainless Steel, Lavender (,000 pack) Loctite 50 ml Square Mix Nozzle, 24 elements, 5.3 mm2 (,000 pack) Loctite ZETA 7720 Visible Light Wand System , 03, 04, Loctite 6 mm D x 000 mm Fiber Optic Light Guide Loctite Replacement Lamp Reflector Module, 00 W for Loctite Indigo , Loctite SCARA Interface Cable Loctite Formable Dispense Tip, 2 Gauge, White Loctite Posi-Link 0-50 Syringe Nest, 0 ml Loctite Posi-Link 0-50 Syringe Nest, 25 ml Loctite Posi-Link ml Dual Cartridge Nest, : and 2: Loctite Posi-Link ml Dual Cartridge Nest, 0: Loctite Posi-Link 5-25 Syringe Nest, 5 ml Loctite Posi-Link 5-25 Syringe Nest, 0 ml Loctite Posi-Link 5-25 Syringe Nest, 25 ml Loctite Universal Syringe Bracket for Loctite Posi-Link Loctite 50 ml Dual Cartridge Bracket for Loctite Posi-Link Loctite PC Interface Cable for Loctite Benchtop Robots , 88, 89, 90, Replacement Bulb, 6" UV for Loctite ZETA 760 Conveyor Loctite Light Blocking Shield Loctite 200 / 400 ml Square Mix Nozzle, 7.5 mm Loctite 3 ml Syringe Barrel, Black (,000 pack) Loctite 3 ml Syringe Air Line Adapter , 2, Loctite 5 ml Syringe Air Line Adapter , 2, Loctite Dispense Tip, 25 gauge, Taper Tip, Helix Thread (50 pack) Loctite Dispense Tip, 25 gauge, Taper Tip, Helix Thread (,000 pack) Loctite Dispense Tip, 27 gauge, Taper Tip, Helix Thread (50 pack) Loctite Dispense Tip, 27 gauge, Taper Tip, Helix Thread (,000 pack) Loctite Posi-Link ml Dual Cartridge Nest, : and 2: Loctite Posi-Link ml Dual Cartridge Nest, : and 2: Loctite Posi-Link ml Dual Cartridge Nest, 0: Loctite 200 / 400 ml Square Mix Nozzle, 24 elements, Threaded Bell End Loctite 200 / 400 ml Square Mix Nozzle, 24 elements, Threaded Bell End Loctite LED Mounting Bracket Loctite Solenoid for 974 Loctite Pinch Tube Valve Loctite 200 / 400 ml Mix Nozzle, 40 elements, Threaded Bell End (0 pack) Loctite Adapter Check Valve Loctite Empty lb. HDPE Bottle , 20,22

124 22 INDEX ITEM NUMBER PRODUCT NAME PAGE NUMBER ITEM NUMBER PRODUCT NAME PAGE NUMBER 495 Loctite Standard Adapter/Check Valve for Nozzles (Single pack) Loctite 50 ml Mix Nozzle, Stepped, 5.4 mm (,000 pack) Loctite UVALOC 000 UV Cure Chamber , Loctite 4 Gauge, /4", Stainless Steel, Olive, Helical Thread (50 pack) Loctite 4 Gauge, /4", Stainless Steel, Olive, Helical Thread (,000 pack) Loctite Feed Line Tubing, Clear, 2.0 mm OD x.4 mm ID, 20 Meters Loctite Feed Line Tubing, Clear,.6 mm OD x.0 mm ID, 20 Meters Loctite UV Bulb, Gallium, UVALOC Loctite UV Bulb, Iron, UVALOC Loctite UV Bulb, Mercury, UVALOC Loctite Digital Syringe Dispensing System , 2, 84, 87, 88, 89, 90, Loctite 7703-HD LED Light Source , Loctite Light Intensity Monitor , 05, 06, Loctite Replacement Foot Switch Loctite O-Ring Replacement Cord Stock, 0.250" diameter Loctite O-Ring Replacement Cord Stock, 0.25" diameter Loctite O-Ring Replacement Cord Stock, 0.093" diameter Loctite O-Ring Replacement Cord Stock, 0.87" diameter Loctite Black Tubing.6 mm OD x.0 mm ID x 20 m Loctite Hysol 050A, Nozzle Loctite Hysol 050 Gas Hot Melt Applicator , Loctite Hysol 050-Lite Hot Melt Applicator , Loctite Hysol 050A Hot Melt Applicator , Loctite 200 / 400 ml Mix Nozzle, 32 Elements Loctite Z Plate Robot Adapter; Posi-Link 200 / 400 Dual Cartridge Feed line tubing 2.0 mm OD x.4 mm ID, black, x 65.6' Loctite Clear Tubing, 3.0 mm OD x.9 mm ID x 20 m Loctite Clear Tubing, 3.0 mm OD x 2.4 mm ID x 20 m Loctite Feed Line Tubing, 3.0 mm OD x 2.4 ID, Black, 20 Meters Loctite Feed Line Tubing, 2.5 mm OD x.9 ID, Black, 20 Meters Loctite Dual Light Guide Balancing Adapter Loctite Single Light Guide,.5 m Long x 5 mm Diameter , 06, Loctite ZETA 7735 UV Wand IM , 03, Loctite ZETA 7740 UV Wand IM , 03, Loctite ZETA 7760 UV Wand IM , 03, Loctite LED Cure Timer , Loctite LED Tip Covers (5 pack) , Loctite Static Mixer-Luer Adapter (2,000 pack) Loctite Replacement Ballast Loctite Replacement Filter Glass , Loctite 748 Replacement Bulb MH , 9703 Loctite Indigo 748 Flood Unit , 09, Loctite CureJet Indigo LED , Loctite LED Controller for CureJet Indigo LED , Loctite CureJet 405 LED , Loctite High Intensity UV Source, 5 VAC , Replacement 5" UV Bulb 300 W/in Loctite /4", Clear, Polyethylene Feed Tube Loctite 3/8", Clear, Polyethylene Feed Tube Loctite Replacement Reservoir Lid O-Ring Loctite /4", Clear, Nylon Feed Tube for Pump-A-Bead Loctite High Intensity UV Source, 220 VAC , Loctite 200 g Gel Tube Kit Loctite Universal Power Cord , Loctite Stainless Steel Poppet Valve , 70, 74, Loctite Fishbach Cartridge Adapter Loctite AC Level Sensor Kit , Loctite Bond-A-Matic 3000 Dispenser , 7, Loctite Bond-A-Matic 3000 Reservoir, 0 to 5 psi with Low Level Sensor , 6, 7, 20, 59, 6, 65, 66, 67, 68, 69, 7, Loctite Bond-A-Matic 3000 Reservoir, 0 to 5 psi with Low Level Sensor , 20, 59, 6, 66, Loctite Bond-A-Matic 3000 Dispenser , 7, Loctite Bond-A-Matic 3000 Reservoir, 0 to 00 psi with Low Level Sensor , 6, 7, 20, 59, 6, 65, 66, 67, 68, 69, 7, Loctite Bond-A-Matic 3000 Reservoir, 0 to 00 psi with Low Level Sensor , 20, 59, 6, 66, Loctite Bond-A-Matic 3000 Reservoir, 0 to 5 psi , 7, 20, 59, 60, 6, 65, 66, 67, 68, 69, 7, Loctite Bond-A-Matic 3000 Reservoir, 0 to 00 psi , 7, 20, 59, 60, 6, 65, 66, 67, 68, 69, 7, 72, Loctite Replacement 24 VDC Sensor for and Only , Loctite 4 Liter Gravity Feed Reservoir , 22, Loctite Replacement Reservoir Body Loctite Visible Lamp for 98027, 9843 or W/in , Loctite Reservoir Lid O-Ring for Loctite Tube Adapter Loctite Replacement Actuator Assembly Loctite Replacement Pump Assembly Loctite Replacement Pump Loctite Positive Displacement Pump , 64, 72, Loctite 200 ml Dual Cartridge Manual Applicator, : and 2: , Loctite 200 ml Dual Cartridge Pneumatic Applicator, : and 2: , Loctite 400 ml Dual Cartridge Manual Applicator, : and 2: , Loctite 400 ml Dual Cartridge Pneumatic Applicator, : and 2: , Loctite Exhaust Plenum Loctite Sight Shield Loctite Sight Shield Loctite Air Deflection Kit Fusion D Bulb 300 W/in , Fusion H Bulb 300 W/in , Fusion V Bulb 300 W/in , Loctite 50 ml Mix Nozzle, 20 elements, Luer (2,000 pack) Loctite 50 ml Replacement Applicator Plunger, : ratio Loctite 50 ml Replacement Applicator Plunger, 2: ratio Loctite Single Light Guide, m Long x 5 mm Diameter , 06, Loctite Dual Light Guide, m Long x 3 mm Diameter , 06, Loctite Poppet Valve (0 to 625 psi) , 70, 74, Loctite Cotton Gloves Loctite Optional 50 ml Applicator Plunger, 4: Ratio Loctite 4: Conversion Kit for Loctite 4: Conversion Kit for Loctite Standard Adapter for 300 ml Cartridge Loctite Standard -Hole Nozzle with Cap Loctite Adapter/Check Valve for Specialty Nozzles Loctite Needle Jet Nozzle Loctite Diagonal Extension Nozzle Loctite Flat Spreader Nozzle Loctite 2-Hole Spreader Nozzle Loctite 3-Hole Spreader Nozzle Loctite Injection Needle Nozzle Loctite Pneumatic Foot Switch Loctite Vertical Stand Loctite Applicator Hanger Arm for Bulk-4 and Bulk Loctite Applicator Hanger Arm for Bulk Loctite Reservoir Liner , Loctite High Viscosity Dispense Valve Machine Mount (0 to 4,000 psi) Loctite Replacement Foot Switch for , Loctite Vertical Syringe Stand , 2, Loctite Syringe Air Line Filter for Syringe Dispensing Loctite Valve Rebuild Kit for Loctite Valve Rebuild Kit for Loctite Anti-Bubbler Kit for Loctite Silicone Tubing for Dispense Valve Purging Loctite Advancing Slide, 2" Stroke , 7, 65, 66, 67, 70, 7, Loctite Replacement 00W Lamp Module , Loctite Replacement Sleeve Kit Loctite Fitting, /4" NPT x /4" Tube, Black, Plastic , Loctite Fitting, /4" NPT x 3/8" Tube, Black, Plastic , Loctite Standard -Hole Nozzle, 0" Diameter x 6" L Loctite Spreader Nozzle (0.08" x 25" sq.) x 47" L Loctite Pencil Point Nozzle, 0.08" Diameter x 24" L Loctite Precision Nozzle, 0.05" Diameter x 20" L Loctite Extension Nozzle, 0.0" Diameter x 50" L Loctite Silicone Rubber Safety Cap Loctite Optional Head Extension Cable for Loctite Heavy Duty Metal Stand Loctite 2-Hole Nozzle Loctite 3-Hole Nozzle Loctite Diagonal Extension Nozzle, 0.0" Diameter x.32" Long Loctite Needle Extension Nozzle, 0.05 Diameter x.32 Long Loctite Spreader Extension Nozzle, (0.09 x 25" sq.) x.22 Long Loctite L-Nozzle (Ideal for Overlap Carton Sealing) Loctite T-Nozzle (Ideal for Center Flap Carton Sealing) Loctite Standard Medium Spray Nozzle Loctite Narrow Spray Nozzle Loctite Ultra Wide Spray Nozzle Loctite Replacement Standard Nozzle, 0.08" Diameter Cone Tip Loctite Tool Hanger/Balancer Loctite Universal Metal Dispenser for 200 / 400 ml Cartridges , Loctite 400 ml Dual Cartridge Manual Dispenser, 0: , Loctite 400 ml Dual Cartridge Pneumatic Applicator, 0: , Loctite Mounting Bracket , Loctite Replacement Silicone Work Surface for Loctite Air Line Filter/Regulator with Pressure Gauge (0 to 50 psi) , 49, Loctite.5 mm ID Tapered Aluminum Nozzle, Straight Thread Loctite Replacement Ballast Visible Arc Bulb, 500 W , Loctite Replacement Filter Glass, Tempered , Loctite Pump-A-Bead II Dispenser , 3, Loctite Nozzle, 0.025" Diameter Loctite Nozzle, 0.035" Diameter Loctite Nozzle, 0.060" Diameter Loctite Optional 50 ml Applicator Plunger, 0: Ratio Loctite 4 Conductor Cable with M-2 Connector Loctite 4-Way Solenoid for Loctite Poppet Valve /4" Tube , 70, 74, 77, Loctite Valve Rebuild Kit Loctite Air Operated Mounted Applicator, 230 VAC Loctite 4-Way Solenoid Valve Kit, 24 VDC Loctite Valve Mount Bracket Kit Loctite Extrusion Hose, 4', 5 VAC Loctite Extrusion Hose, 4', 230 VAC Loctite Extrusion Hose, 6', 5 VAC Loctite Extrusion Hose, 6', 230 VAC Loctite Extrusion Hose, 8', 5 VAC Loctite Extrusion Hose, 8', 230 VAC Loctite Extrusion Hose, 0', 5 VAC

125 23 INDEX ITEM NUMBER PRODUCT NAME PAGE NUMBER ITEM NUMBER PRODUCT NAME PAGE NUMBER Loctite Extrusion Hose, 0', 230 VAC Loctite Extrusion Hose, 2', 5 VAC Loctite Extrusion Hose, 2', 230 VAC Loctite Extrusion Hose, 6', 5 VAC Loctite Extrusion Hose, 6', 230 VAC Loctite Extrusion Hose, 8', 5 VAC Loctite Extrusion Hose, 8', 230 VAC Loctite Extrusion Hose, 24', 5 VAC Loctite Extrusion Hose, 24', 230 VAC Loctite Spray Hose, 4', 5 VAC Loctite Spray Hose, 4', 230 VAC Loctite Spray Hose, 6', 5 VAC Loctite Spray Hose, 6', 230 VAC Loctite Spray Hose, 8', 5 VAC Loctite Spray Hose, 8', 230 VAC Loctite Spray Hose, 0', 5 VAC Loctite Spray Hose, 0', 230 VAC Loctite Spray Hose, 2', 5 VAC Loctite Spray Hose, 2', 230 VAC Loctite Spray Hose, 6', 5 VAC Loctite Spray Hose, 6', 230 VAC Loctite Spray Hose, 8', 5 VAC Loctite Spray Hose, 8', 230 VAC Loctite Spray Hose, 24', 5 VAC Loctite Spray Hose, 24', 230 VAC Loctite Bead Nozzle /2" x 0.020" Orifice Loctite Bead Nozzle " x 0.020" Orifice Loctite Bead Nozzle 2" x 0.020" Orifice Loctite Bead Nozzle 3" x 0.020" Orifice Loctite Bead Nozzle /2" x 0.030" Orifice Loctite Bead Nozzle " x 0.030" Orifice Loctite Bead Nozzle 2" x 0.030" Orifice Loctite Bead Nozzle 3" x 0.030" Orifice Loctite Bead Nozzle /2" x 0.040" Orifice Loctite Bead Nozzle " x 0.040" Orifice Loctite Bead Nozzle 2" x 0.040" Orifice Loctite Bead Nozzle 3" x 0.040" Orifice Loctite Bead Nozzle /2" x 0.050" Orifice Loctite Bead Nozzle " x 0.050" Orifice Loctite Bead Nozzle 2" x 0.050" Orifice Loctite Bead Nozzle 3" x 0.050" Orifice Loctite Bead Nozzle /2" x 0.060" Orifice Loctite Bead Nozzle " x 0.060" Orifice Loctite Bead Nozzle 2" x 0.060" Orifice Loctite Bead Nozzle 3" x 0.060" Orifice Loctite Bead Nozzle /2" x 0.070" Orifice Loctite Bead Nozzle " x 0.070" Orifice Loctite Bead Nozzle 2" x 0.070" Orifice Loctite Bead Nozzle 3" x 0.070" Orifice Loctite Bead Nozzle /2" x 0.080" Orifice Loctite Bead Nozzle " x " Orifice Loctite Bead Nozzle 2" x 0.080" Orifice Loctite Bead Nozzle 3" x 0.080" Orifice Loctite Bead Nozzle /2" x 0.090" Orifice Loctite Bead Nozzle " x 0.090" Orifice Loctite Bead Nozzle 2" x 0.090" Orifice Loctite Bead Nozzle 3" x 0.090" Orifice Loctite Bulk-4 Hopper Upgrade, 40 lbs Loctite Bulk-34 Hopper Upgrade, 78 lbs Loctite Floor Stand Kit For Bulk Units Loctite Hose Cradle Loctite Tension Balancer Loctite Cradle and Tension Balancer Loctite Feed Line Adapter, Loctite Feed Line Adapter, Loctite Button Nozzle, 0.02" Orifice Loctite Button Nozzle, 0.05" Orifice Loctite Button Nozzle, 0.025" Orifice Loctite Button Nozzle, 0.030" Orifice Loctite Button Nozzle, 0.040" Orifice Loctite Button Nozzle, 0.050" Orifice Loctite Button Nozzle, 0.060" Orifice Loctite Button Nozzle, 0.070" Orifice Loctite Button Nozzle, 0.080" Orifice Loctite Button Nozzle, 0.090" Orifice Loctite Proximity Sensor Assembly Loctite Optical Sensor Assembly Loctite Sensor Cord Extension, 0 Feet Loctite Direction Nozzle O-Ring (0 pack) Loctite Direction Nozzle Screw (5 pack) Loctite Blank Screw Assembly (5 pack) Loctite Direction Nozzle Assembly, 0.00" Diameter (2 pack) Loctite Direction Nozzle Assembly, 0.020" Diameter (2 pack) Loctite Direction Nozzle Assembly, 0.030" Diameter (2 pack) Loctite Direction Nozzle Assembly, 0.040" Diameter (2 pack) Loctite Timer Cord, 24 VDC Application Loctite Timer Cord, Single Line Voltage Loctite Timer Cord, 2 Line Voltage Loctite Timer Cord Bulk 34 Line Voltage Loctite Timer Cord Bulk 34, 24 VDC Voltage Loctite Direction Nozzle, 0.00" Diameter (2 pack) Loctite Direction Nozzle, 0.020" Diameter (2 pack) Loctite Direction Nozzle, 0.030" Diameter (2 pack) Loctite Direction Nozzle, 0.040" Diameter (2 pack) Loctite T-Bar Nozzle, 2" x " Loctite T-Bar Nozzle, 2" x 2" Loctite T-Bar Nozzle, 2" x 3" Loctite Y-Bar Nozzle, 2" x " Loctite Y-Bar Nozzle, 2" x 2" Loctite Y-Bar Nozzle, 2" x 3" Loctite Swirl Nozzle, 0.030" Orifice Loctite Swirl Nozzle, 0.045" Orifice Loctite Swirl Nozzle, 0.060" Orifice Loctite Swirl Nozzle, 0.080" Orifice Loctite Spray Nozzle and O-Ring, 0.020" Orifice Loctite Spray Nozzle and O-Ring, 0.030" Orifice Loctite Spray Nozzle and O-Ring, 0.040" Orifice Loctite Spray Nozzle and O-Ring, 0.050" Orifice Loctite 2 Hand Applicator Cord, Switch Control Loctite 2 Hand Applicator Cord, 2 Switch Control Loctite Hysol 2 Hand Extrusion Controller, 5 VAC Loctite Hysol 2 Hand Spray Controller, 5 VAC Loctite Swirl Nozzle Assembly Loctite Spray Nozzle Assembly Fan Air Cap Loctite Timer Cord, Single Line, 24 VDC Loctite External Interface Cable for Bulk Loctite External Interface Cable for Bulk Loctite Spray Nozzle Assembly Cone Air Cap Pre-Filter for Benchtop Filters Carbon Bed Filter for Benchtop Filters HEPA / Carbon Filter Exhaust Arm Damper Exhaust Arm Exhaust Arm Nozzle 40 mm Loctite Operation Box for SCARA Loctite Hysol 2 Hand Extrusion Controller, 230 VAC Loctite Hysol 2 Hand Spray Controller, 230 VAC Loctite External Interface Cable for Bulk Loctite Solenoid Valve Module , 88, 89, 90, Loctite Nozzle Adapter/Check Valve for Loctite Hysol 050 Hot Melt Applicator Loctite -Hole Nozzle, 0.08" Diameter, for Loctite Hysol 050 Hot Melt Applicator (5 pack) Loctite Replacement Filter Glass for Loctite Replacement Light Blocking Curtain for Hand Pump Washers (3 pack) Loctite Low Viscosity Fluid Pump System, : ratio, 55 gallon Loctite Low Viscosity Fluid Pump System, 3: ratio, 55 gallon Loctite Low Viscosity Fluid Pump System, 3: ratio, 55 gallon Loctite Low Viscosity Fluid Pump System, 3: ratio, 5 gallon Loctite Low Viscosity Fluid Pump System, 3: ratio, 5 gallon Loctite Low Viscosity Fluid Pump System, 4: ratio, 55 gallon Loctite Low Viscosity Fluid Pump System, 4: ratio, 55 gallon Loctite Low Viscosity Fluid Pump System, 4: ratio, 5 gallon Loctite Low Viscosity Fluid Pump System, 4: ratio, 5 gallon Loctite 4 /4" Air Motor Loctite 6" Air Motor Loctite CS Pump Tube Loctite Inert Pump Tube Loctite CS Pump Tube Loctite Inert Pump Tube Loctite CS, 55 Gallon Twin Post Primer Loctite CS, 5 Gallon Single Post Primer Loctite Inert, 55 Gallon Twin Post Primer Loctite Inert, 5 Gallon Single Post Primer Loctite Pump Hoist Loctite Pump Stop Loctite 55 Gallon Drum Cover Loctite 5 Gallon Pail Cover Loctite Low Level Cut-off 55 Gallon Loctite Microswitch (Low Level) Loctite Wall Mount Kit for Ball Valves Loctite High Viscosity Paste Pump System, 22: ratio, 55 gallon Loctite High Viscosity Paste Pump System, 22: ratio, 5 gallon Loctite High Viscosity Paste Pump System, 22: ratio, 55 gallon Loctite High Viscosity Paste Pump System, 22: ratio, 5 gallon Loctite High Viscosity Paste Pump System, 44: ratio, 55 gallon Loctite High Viscosity Paste Pump System, 44: ratio, 5 gallon Loctite High Viscosity Paste Pump System, 44: ratio, 55 gallon Loctite High Viscosity Paste Pump System, 44: ratio, 5 gallon Loctite High Viscosity Paste Pump System, 64: ratio, 55 gallon Loctite High Viscosity Paste Pump System, 64: ratio, 5 gallon Loctite High Viscosity Paste Pump System, 64: ratio, 55 gallon Loctite High Viscosity Paste Pump System, 64: ratio, 5 gallon Loctite CS Pump Tube with Inert Seals Loctite CS Pump Tube with Inert Seals Loctite High Viscosity Paste Pump System, 22: ratio, 5 gallon Loctite High Viscosity Paste Pump System, 44: ratio, 5 gallon Loctite High Viscosity Paste Pump System, 64: ratio, 5 gallon

126 24 INDEX ITEM NUMBER PRODUCT NAME PAGE NUMBER ITEM NUMBER PRODUCT NAME PAGE NUMBER Loctite High Viscosity Paste Pump System, 22: ratio, 55 gallon Loctite High Viscosity Paste Pump System, 44: ratio, 55 gallon Loctite High Viscosity Paste Pump System, 64: ratio, 55 gallon Loctite Syringe Finger Switch ,, Loctite Meter Mix 000L Dispense System Fixed Ratio , Loctite Meter Mix 000L Dispense System Variable Ratio , Loctite Meter Mix 000H Dispense System Fixed Ratio , Loctite Meter Mix 000H Dispense System Variable Ratio , Loctite Meter Mix 2000 Dispense System Fixed Ratio , Loctite Meter Mix 2000 Dispense System Variable Ratio , Loctite Meter Mix 3000 Dispense System Fixed Ratio , Loctite Meter Mix 3000 Dispense System Variable Ratio , Loctite Abrasion Resistant Pumps Instead of Mild Steel Loctite 304 Stainless Steel Pumps Instead of Mild Steel Loctite 8 mm High, 8 mm Low MMD Pump Pair Loctite 8 mm High, 0 mm Low MMD Pump Pair Loctite 8 mm High, 5 mm Low MMD Pump Pair Loctite 8 mm High, 20 mm Low MMD Pump Pair Loctite 8 mm High, 25 mm Low MMD Pump Pair Loctite 0 mm High, 8 mm Low MMD Pump Pair Loctite 0 mm High, 0 mm Low MMD Pump Pair Loctite 0 mm High, 5 mm Low MMD Pump Pair Loctite 0 mm High, 20 mm Low MMD Pump Pair Loctite 0 mm High, 25 mm Low MMD Pump Pair Loctite 5 mm High, 8 mm Low MMD Pump Pair Loctite 5 mm High, 0 mm Low MMD Pump Pair Loctite 5 mm High, 5 mm Low MMD Pump Pair Loctite 5 mm High, 20 mm Low MMD Pump Pair Loctite 5 mm High, 25 mm Low MMD Pump Pair Loctite 20 mm High, 8 mm Low MMD Pump Pair Loctite 20 mm High, 0 mm Low MMD Pump Pair Loctite 20 mm High, 5 mm Low MMD Pump Pair Loctite 20 mm High, 20 mm Low MMD Pump Pair Loctite 20 mm High, 25 mm Low MMD Pump Pair Loctite 25 mm High, 8 mm Low MMD Pump Pair Loctite 25 mm High, 0 mm Low MMD Pump Pair Loctite 25 mm High, 5 mm Low MMD Pump Pair Loctite 25 mm High, 20 mm Low MMD Pump Pair Loctite 25 mm High, 25 mm Low MMD Pump Pair Loctite Custom Diameter High, 8 mm Low MMD Pump Pair Loctite Custom Diameter High, 0 mm Low MMD Pump Pair Loctite Custom Diameter High, 5 mm Low MMD Pump Pair Loctite Custom Diameter High, 20 mm Low MMD Pump Pair Loctite Custom Diameter High, 25 mm Low MMD Pump Pair Loctite Custom Diameter High, 30 mm Low MMD Pump Pair Loctite Custom Diameter High, 35 mm Low MMD Pump Pair Loctite 8 mm High, Custom Diameter Low MMD Pump Pair Loctite 0 mm High, Custom Diameter Low MMD Pump Pair Loctite 5 mm High, Custom Diameter Low MMD Pump Pair Loctite 20 mm High, Custom Diameter Low MMD Pump Pair Loctite 25 mm High, Custom Diameter Low MMD Pump Pair Loctite 30 mm High, Custom Diameter Low MMD Pump Pair Loctite 35 mm High, Custom Diameter Low MMD Pump Pair Loctite 5 L Stainless Steel Tank with Cover Loctite 7.5 L Stainless Steel Tank with Cover Loctite 7.5 L Tank High-Low and Vac. Ready Mild Steel (MMD 3000) Loctite 7.5 L Tank High-Low and Vac. Ready Stainless Steel (MMD 3000) Loctite Recirculation for 5 or 7.5 L Tanks Loctite 6.9 CFM Vacuum Pump Assembly Loctite Remote Operator Controls Loctite Pressure-Vacuum Tank Mild Steel Loctite Electric Agitator (5 gallon) Tank Loctite Tank Support Stand Holds 2 Tanks Loctite Disposable Desiccant Dryer 5 Gallon Loctite Nitrogen Harness Assembly Tank Loctite Nitrogen Harness Assembly 2 Tanks Loctite Polyethylene Tank Assembly Loctite Polyethylene Follower Plate Loctite Tank Air Pressure Assembly Loctite Low Level Control Sensor (MMD 3000 only) Loctite High & Low Level Control Sensors (MMD 3000 only) Loctite Pressure-Vacuum Tank Stainless Steel Loctite Pump Inlet Adapter Fitting Loctite Disposable Desiccant Air Dryer and Lock Down Lid Loctite Follower Plate with Handle Loctite Electric Agitator Assembly with Cover Loctite Aluminum Accumulator; High-Low Electric Controls Loctite Stainless Steel Accumulator; High-Low Electric Controls Loctite Precision Flow Control Drive (MMD 3000 only) Loctite Electrical Enclosure and Controls for Heat Load Loctite Electrical Enclosure and Controls for 2 Heat Loads Loctite Electrical Enclosure and Controls for 3 Heat Loads Loctite Electrical Enclosure and Controls for 4 Heat Loads Loctite Heat Blanket (720W) and Insulation for 5 or 7.5 L Tank Loctite Hose Heater (50W) and Insulation for /2" or 3/8" x 2' long Loctite Pistol Grip - Pneumatic Switch Option (MMD 000) Loctite Dispense Valve : Nose, Abrasion Resistant Loctite Dispense Valve : Nose, Stainless Steel Loctite 3 Way Stainless Steel Ratio Check Valve Upgrade Loctite Low Level Sensor for one 7.5 L Tank Loctite Vacuum Valving Assembly.0" Mild Steel Loctite Vacuum Valving Assembly.0" Stainless Steel Loctite Shipping Crate - 5 and 7.5 L Systems Loctite 7.5 L Tank, High-Low Sensor Ready (MMD 3000 only) Loctite LCA Tubing Applicator, 2 mm Loctite LCA Tubing Applicator, 3 mm Loctite LCA Tubing Applicator, 4 mm Loctite LCA Tubing Applicator, 5 mm Loctite LCA Tubing Applicator, 6 mm Loctite 3/4" MNPT x /2" MNPT Hex Nipple, Brass Loctite Fitting to Primer 3 Way Valve Loctite Secondary Regulator (0 to 725 psi) Loctite Dispense Valve 0: Nose, Stainless Steel Loctite Dispense Valve 0: Nose, Abrasion Resistant Loctite High Pressure 3/4" x 6' Stainless Steel, PTFE Lined 5,000 psi max Loctite High Pressure 3/4" x 2' Stainless Steel, PTFE Lined 5,000 psi max Loctite High Pressure 3/4" x 24' Stainless Steel, PTFE Lined 5,000 psi max Loctite High Pressure " x 6' Stainless Steel, PTFE Lined 5,000 psi max Loctite High Pressure " x 2' Stainless Steel, PTFE Lined 5,000 psi max Loctite High Pressure " x 24' Stainless Steel, PTFE Lined 5,000 psi max Loctite Medium Pressure Hose 3/8" x 6' 2,250 psi Loctite Medium Pressure Hose for Dispense Valve 3/8" x 2' 2,250 psi Loctite Medium Pressure Hose 3/8" x 24' 2,250 psi Loctite Medium Pressure Hose /2" x 6' 2,000 psi Loctite Medium Pressure Hose for Dispense Valve /2" x 2' 2,000 psi Loctite Medium Pressure Hose /2" x 24' 2,000 psi Loctite Medium Pressure Hose 3/4" x 6',500 psi Loctite Medium Pressure Hose 3/4" x 2',500 psi Loctite Medium Pressure Hose 3/4" x 24',500 psi Loctite Medium Pressure Hose " x 6',500 psi Loctite Medium Pressure Hose " x 2',500 psi Loctite Medium Pressure Hose " x 24',500 psi Loctite " JIC M x 3/4" MNPT Connector Loctite 3/4" JIC M x 3/4" MNPT Connector Loctite 3/4" JIC M x /2" MNPT Connector Loctite /2" JIC M x 3/4" MNPT Connector Loctite /2" JIC M x /2" MNPT Connector Loctite /2" JIC M x /4" MNPT Connector Loctite 3/8" JIC M x /2" MNPT Connector Loctite 3/8" JIC M x 3/8" MNPT Connector Loctite 3/8" JIC M x /4" MNPT Connector Loctite 3/8" JIC M x 3/8" MNPT Elbow Loctite /2" JIC M x /4" MNPT Elbow Loctite /2" JIC M x /2" MNPT Elbow Loctite 3/4" JIC M x 3/4" MNPT Elbow Loctite 3/4" JIC M x /2" MNPT Elbow Loctite " JIC M x 3/4" MNPT Elbow Loctite 3/4" FNPT x /4" MNPT Reducing Adapter Loctite 3/4" FNPT x /2" MNPT Reducing Adapter Loctite /2" FNPT x /8" MNPT Reducing Adapter Loctite /2" FNPT x /4" MNPT Reducing Adapter Loctite 3/8" FNPT x /8" MNPT Reducing Adapter Loctite 3/8" FNPT x /4" MNPT Reducing Adapter Loctite High Viscosity Hand Gun Pistol Grip (0 to 4,000 psi) Loctite High Viscosity Hand Gun In-Line (0 to 3,400 psi) Loctite Primary Fluid Regulator Assembly (250 to 4,500 psi) Loctite Air Operated Fluid Regulator (250 to 4,500 psi Loctite Optional Gauge and Isolator Assembly (0 to 5,000 psi) Loctite Secondary Fluid Regulator Assembly (0 to 725 psi) Loctite Optional Gauge & Isolator Assembly (0 to,000 psi) Loctite Particle Filter Assembly (0 to 5,000 psi) Loctite Particle Filter Purge Tube Upgrade Kit Loctite FLR (Filter, Lubricator, Regulator) Assembly, /2 inch ports (0 to 00 psi) Loctite /4" MNPT, " Long x 0.50" ID Loctite /4" MNPT, " Long x 0.094" ID Loctite /4" MNPT, " Long x 0.063" ID Loctite /4" MNPT, 2.5" Long x 0.50" ID Loctite /4" MNPT, 2.5" Long x 0.094" ID Loctite /4" MNPT, 2.5" Long x 0.063" ID Loctite /8" MNPT, " Long x 0.50" ID Loctite /8" MNPT, " Long x 0.094" ID Loctite /8" MNPT, " Long x 0.063" ID Loctite /8" MNPT, 2.5" Long x 0.50" ID Loctite /8" MNPT, 2.5" Long x 0.094" ID Loctite /8" MNPT, 2.5" Long x 0.063" ID Loctite.5 mm ID Tapered Stainless Steel Nozzle, Straight Thread Loctite 2 mm ID Tapered Stainless Steel Nozzle, Straight Thread Loctite 3 mm ID Tapered Stainless Steel Nozzle, Straight Thread Loctite 4 mm ID Tapered Stainless Steel Nozzle, Straight Thread Loctite.5 mm ID Tapered Acetal Copolymer Nozzle, Straight Thread Loctite 2 mm ID Tapered Acetal Copolymer Nozzle, Straight Thread Loctite 3 mm ID Tapered Acetal Copolymer Nozzle, Straight Thread Loctite 4 mm ID Tapered Acetal Copolymer Nozzle, Straight Thread Loctite 2 mm ID Tapered Aluminum Nozzle, Straight Thread Loctite 3 mm ID Tapered Aluminum Nozzle, Straight Thread Loctite 4 mm ID Tapered Aluminum Nozzle, Straight Thread Loctite Adapter for Straight Thread Nozzles Loctite MMD Hose 3/6" X 24", Stainless Steel

127 25 INDEX ITEM NUMBER PRODUCT NAME PAGE NUMBER ITEM NUMBER PRODUCT NAME PAGE NUMBER Loctite MMD Hose 3/6" X 72", Stainless Steel Loctite MMD Hose 3/6" X 20", Stainless Steel Loctite MMD Hose /4" X 24", Mild Steel Loctite MMD Hose /4" X 72", Mild Steel Loctite MMD Hose /4" X 20", Mild Steel Loctite MMD Hose /4" X 24", Stainless Steel Loctite MMD Hose /4" X 72", Stainless Steel Loctite MMD Hose /4" X 20", Stainless Steel Loctite MMD Hose 3/8" X 24", Mild Steel Loctite MMD Hose 3/8" X 72", Mild Steel Loctite MMD Hose 3/8" X 20", Mild Steel Loctite MMD Hose 3/8" X 24", Stainless Steel Loctite MMD Hose 3/8" X 72", Stainless Steel Loctite MMD Hose 3/8" X 20", Stainless Steel Loctite MMD Hose /2" X 24", Mild Steel Loctite MMD Hose /2" X 72", Mild Steel Loctite MMD Hose /2" X 20", Mild Steel Loctite MMD Hose /2" X 24", Stainless Steel Loctite MMD Hose /2" X 72", Stainless Steel Loctite MMD Hose /2" X 20", Stainless Steel Loctite High and Low Level Sensor for one 5 or 7.5 L Tank Loctite High and Low Level Sensors with Auto Refill Loctite Disposable Desiccant Air Dryer Loctite Aluminum Accumulator; High-Low Pneumatic Controls Loctite Stainless Steel Accumulator; High-Low Pneumatic Controls Loctite Shipping Crate 5 Gallon Tank Systems Loctite Low Pressure Fluid Regulator (30 to 200 psi) Loctite Low Pressure Fluid Regulator (5 to 30 psi) Loctite Spray Nozzle Kit 0.04 Diameter , 69, Loctite Spray Nozzle Kit Diameter , 69, Loctite Spray Nozzle Kit Diameter Loctite Spray Valve Seal Kit Loctite Spray Valve Hose and Fitting Kit Loctite Spray Valve Piston Repair Kit Loctite PLC Program Backup/Upgrade (MMD 3000 only) Loctite 5 or 7.5 L Tank Vacuum Ready, Mild Steel Loctite Heat Blanket Insulation 750 watts Loctite 250 ml Squeeze Tube Adapter Loctite Pail Pump Fitting, 3/4" MNPT x /4" MNPT Loctite Pistol Grip, Electric Switch Option, (MMD 2000, 3000) Loctite Lever Actuated, /4" Pneumatic Switch Option Loctite Lever Actuated, 3/8" Pneumatic Switch Option Loctite Lever Actuated, 3/8" Electric Switch Option Loctite Air Operated Mounted Applicator, 5 VAC Loctite 4-Way Solenoid Valve Kit, 5 VAC Loctite 4-Way Solenoid Valve Kit, 230 VAC Loctite Mounting Bracket for Loctite Applicator Assembly Loctite Standard Pump Head Loctite Applicator Nozzle,.4 mm ID Loctite Applicator Nozzle,.9 mm ID Loctite Applicator Nozzle, 2.4 mm ID Loctite Valve Mounting Boom 5 or 7 Liter Tanks Loctite Valve Mounting Boom 5 Gallon Tanks Loctite Cable, Loctite SCARA Robot for use with Junction Box, 25 Pin, M-F Loctite Junction Box Cable for Benchtop Robots, 37 Pin MD x 25 Pin FD , 88, 89, 90, Loctite 200 / 400 ml Mix Nozzle, Stepped, 32 elements (50 pack) Loctite 200 / 400 ml Mix Nozzle, Stepped, 48 elements (0 pack) Loctite AC Battery Charger Loctite Teach Point Software for Loctite Benchtop Robots , 88, 89, 90, Loctite Teach Pendant for Loctite Benchtop Robots , 88, 89, Loctite PLC Interface Cable (MMD 3000 only) Loctite Posi-Link 0-50 Cartridge Cradle Loctite Posi-Link 0-50, 0 ml Barbed Piston Loctite Posi-Link 0-50, 25 ml Barbed Piston Loctite Posi-Link 5-25, 5 ml Barbed Piston Loctite Posi-Link 5-25, 0 ml Barbed Piston Loctite Posi-Link 5-25, 25 ml Barbed Piston Loctite 200 Series Light Curtain Loctite 300 Series Light Curtain Loctite 400 / 500 Series Light Curtain Loctite 200 Series Workbench Loctite 300 Series Workbench Loctite 400 / 500 Series Workbench Loctite 200 Series Slide Door Loctite 300 Series Slide Door Loctite 400 / 500 Series Slide Door Loctite SCARA Light Curtain Loctite SCARA Series Workbench Loctite AC Charger for LED-HD Loctite Applicator Nozzle,.2 mm ID Loctite Pressure Safety Relief for Loctite Replacement Tubing for Loctite Replacement Nozzle for Loctite Nut and Sleeve for Loctite Reservoir Lid Sub-Assembly O-Ring for Loctite Silicone Grease 6 gram , Loctite Reservoir Liner for Shot Miser Reservoir Loctite Vari-Drop Applicator Brushes , Loctite Dial-A-Seal Applicator , Loctite Pump Rebuild Kit Loctite Replacement Turret Loctite Replacement Cap for Liter Bottle Loctite LED-HD Timer Handle Loctite CureJet LED Dosimeter Adapter , Loctite SCARA-N Robot, 444A, 4A 220V CE , Loctite SCARA-N Robot, 444A, 4A, 220V , Loctite SCARA-N Robot, 444A 4A, 0V CE , Loctite SCARA-N Robot, 444A, 4A,0V , Loctite SCARA-N Robot, 443A, 3A 220V , Loctite SCARA-N Robot, 443A, 3A, 0V CE , Loctite SCARA-N Robot, 443A 3A, 0V , Loctite Interconnecting Cable for CureJet Controller 3 m Loctite Interconnecting Cable for CureJet Controller m Loctite SCARA-N Robot, 443A, 3A 220V CE , Loctite Hysol PUR Hot Melt Dispenser , Loctite Teach Pendant for Loctite S440 Series SCARA-N Robot Loctite Muti-Function Digital Controller , 7, 59, 6, 65, 66, 67, 68, 7, Loctite Fiber Optic Light Guide Radiometer Adapter Loctite Static Mix Nozzle 8mm x 32E (0 pack) Loctite Static Mix Nozzle 8mm x 32E (,000 pack) Loctite 50 ml-s 0: Spare Plunger Loctite 50 ml-s 0: Dual Cartridge Manual Applicator , Loctite Static Mixer 50 ml, 0:-S (0 pack) , Loctite DuraPump Pneumatic MMA Custom system Loctite DuraPump Pneumatic Custom GP system Loctite DuraPump Programmable Custom Ratio System Loctite DuraPump Pneumatic MMA 0: system Loctite DuraPump Pneumatic 0: GP system Loctite DuraPump Programmable 0: GP System Loctite DuraPump Programmable 4: GP System Loctite DuraPump Pneumatic 4: GP system Loctite DuraPump Pneumatic 2: GP system Loctite DuraPump Programmable 2: GP System Loctite DuraPump Pneumatic MMA : system Loctite DuraPump Pneumatic : GP system Loctite DuraPump Programmable : GP System Loctite Nozzle, Aero Gasket Cartridge, 0 PK Loctite Cartridge-Syringe Adapter, /4" NPT Loctite 2-Hand Anti-Tie-Down Switch Set , Loctite Cable Connector Plug Kit Loctite LED-HD Pistol Grip Battery Kit Loctite Needle-Cartridge Adapter, /4" NPT Loctite Hose Heat Controller for or 2 Heated Zones Loctite Low Level Sensing Option Poly Tank Loctite Low Level Sensing Option Stainless Steel Tank Loctite Dual Tank Stand Loctite Tank Heater and Controls Option (For Stainless Steel Tank Only) Loctite Agitator Assembly (For Stainless Steel Tank Only) Loctite Follower Plate with Handle (For Stainless Steel Tank Only) Loctite Disposable Desiccant Air Dryer Option Loctite 7 L Stainless Steel Gravity Tank with Cover Loctite 9.5 L Poly Gravity Tank with Cover Loctite DuraPump Pistol Grip, Pneumatic Switch (All ratios) Loctite DuraPump Dispense Valve MMA with Snuffback (All ratios) Loctite DuraPump Dispense Valve MMA (All ratios) Loctite DuraPump Dispense Valve with Snuff back (All ratios) Loctite DuraPump Dispense Valve (All ratios) Loctite DuraPump Heated Hose Option, 44" Loctite DuraPump Heated Hose Option, 96" Loctite DuraPump Heated Hose Option, 48" Loctite Hose for Dispense Valve 3/8" x 96" MMA Loctite Hose for Dispense Valve 3/8" x 24" MMA Loctite Hose for Dispense Valve 3/8" x 96" General Purpose Loctite Hose for Dispense Valve 3/8" x 24" General Purpose Loctite Hose for Dispense Valve 3/8" x 44" General Purpose Loctite Hose for Dispense Valve 3/8" x 96" MMA Loctite Precision Hydraulic Flow Controller Loctite Spray Timer Cable Bulk Loctite 200 / 400 ml Mix Nozzle, Stepped, 6 mm (2,000 pack) Loctite Adapter for /8"-28 BSPP Nozzles, /8" BSPP x /4" NPS Loctite Tank Feed Line Fitting Loctite Replacement Battery Kit for Loctite LED Light Sources Loctite Precision O-Ring Kit Loctite PLC Cable , Loctite Replacement Reservoir Lid O-Ring Loctite Pneumatic Supply Fitting for Loctite Valves and Advancing Slide Pneumatic Fitting for Loctite Pressure Sensor and Cable for In-line Flow Monitor ANZ023N0 Loctite Standard Adapter / Check Valve / Jam Nut for Nozzles